Parts for Arbor Shaft Assembly

Transcription

1 Parts for Arbor Shaft Assembly ITEM PART DESCRIEPTION 1 P Key, 3/8 x 2-3/4 2 P Arbor nut RH thread 3 P Bushing SK x 1-11/ (14, 18, 20, 26 ) 4 P Sheave 6 GR - 3V [35 HP] (14,18",20 ) P Sheave 6GR - 3V [35 HP] (26") P Sheave 6GR - 3V [35 HP] (30") 5 P Pillow block 1-11/16 (2) 6 P Arbor wrench 1-1/2 Hex 7 P Blade shaft 8 P Replacement bearing 9 P Key ¼ x 1-3/4 10 P Drive Pin 3/8 x 1-3/8 11 P Inside collar 4-1/2 12 P Arbor nut left hand thread 13 P Outside collar 4-1/2 30

2 Parts for Engine Drive Assembly ITEM PART # DESCRIPTION 1 P HHCS 5/8 x 6 full thread (2 req'd) 2 P Soc. head cap screw 3/8 x 2 3 P Key 3/8 x 2 4 P Belt 3VX/ P Belt A-57 6 P Engine Pulley Bushing SK 1-7/16 S/N P Engine Pulley Bushing SK 1-7/16 S/N 28 UP 7 P Idler pulley 8 P Sheave 6 Gr / 3V / 5.3 Dia. (14,18", 20 sawing) P Sheave 6 Gr / 3V/ 4.75 Dia. (26" sawing) S/N P Sheave 6 Gr / 3V/ 4.75 Dia. (26" sawing) S/N 28 UP P Sheave 6 Gr / 3V/ 4.12 Dia. (30" sawing) 9 P Idler spring 11 P Disengage bar P Extension free wheel 12 P Idler bar w/stud 13 P Disengage bracket & Lifting Bail 14 P Hyd engine pulley 15 P Belt guard 35 (not shown) 18 P Engine Wisconsin Model W Spec # 31

3 Parts for Front Axle ITEM PART DESCRIPTION 1 P Set collar 1 (2 req'd) 2 P Bearing retainer (2 reqd) 3 P Split babbit bearing /4 (2 req'd) 4 P Solenoid 5 P Wheel w/bearing 10 x 2-1/2) 6 P Wheel bearing w/sleeve (2 req'd) 7 P Grease zerk (2 req'd) 8 P Breather cap 9 P Cartridge 10 P Check valve (not shown) 11 P Flow control 3/8 12 P Hyd. cylinder 2 x 6 13 P Hyd. fitting 6-6 x P Hyd. fitting 8-6 x P Hyd. hose 3/8 x 18 (2 req'd) 16 P Hydraulic Power Unit w/solenoid 17 P Relief valve (not shown) 18 P Front axle 19 P Retaining pin 20 P Seal kit for hyd. cylinder (not shown) 32

4 Parts for Rear Axle ITEM PART DESCRIPTION 1 P Adjust. bolt 1/2 x 4 1/2 full thread 2 P Spur gear 80T 1 1/4 3 P Key 3/8 x 13/4 4 P Key 3/8 x 2 3/4 5 P Pillow block - TB 1 1/4 (2 reqd) 6 P Axle adjuster 7 P Wheel w/bushing 10 (2 req'd) 8 P Axle shim 9 P Mount angle 1 10 P Mount angle 2 11 P Rear axle 33

5 Parts for Depth Control ITEM PART DESCRIPTION 1 P Bushing 3/8 x 1/4 (2 req'd) 2 P Cable Assembly 3 P Cable guide 4 P Bolt 3/8 x 1-1/2 5 P Indicator knob 6 P Indicator pulley 7 P Tension spring 8 P Indicator mount 34

6 Gauges and Misc. Parts ITEM PART DESCRIPTION 1 P Cable mount 2 P Amp gauge (35 & 65 HP) 3 P Ignition switch (not shown) 4 P Switch knob 5 P Hour meter / Tachometer 6 P Decal set 7 P Wear strip [2] 8 P Switch assembly 9 P Univ. bushing 7/8 - (not shown) 10 P Blind cover 11 P Choke cable 12 P Depth knob 13 P Gas cap w/gauge 14 P Securing L-bolt 3/8 (2 req'd) 15 P Throttle cable 16 P Wire Harness Primary P Wire Harness Auxiliary Switches 17 P Decal Instrument panel 18 P Instrument enclosure 35

7 Parts for Blade Guard and Water System ITEM PART DESCRIPTION 1 P Elbow, male 8MP x 8MT - 90' 2 P Hose clamp # 6 (4 req'd) 3 P Hose barb 8NT x 6HB (3 req'd) 4 P Ball valve 1/2 x 90' 5 P Return spring 6 P Spray flap 7 P Rivet 3/16 (2 reqd) 8 P Water hose 3/8 9 P Tee, pipe 8NT@ x 8FP x 817P 10 P Bushing, hex 1/2 x 1/8 11 P Water safety switch 12 P Hose coupling w/gasket Part # P " Blade Guard Assembly Part # P " Blade Guard Assembly Part # P " Blade Guard Assembly Part # P " Blade Guard Assembly 36

8 Electric Water Pump Option - Part # ITEM PART DESCRIPTION 1 P Hose coupler x 3/4 2 P Hyd. elbow 3/ P Barb. connector 3/ P Barb. connector 1/2 x 3/4 5 P Hose clamp #12 (2 req'd) 6 P Water hose 3/ Water pump 12VDC 9 P Spacer (not shown) 11 P Switch 37

9 Parts for Drive Assembly ITEM PART # DESCRI[PTION 1 P Sq. head set screw 3/8 x 2 2 P Key 3/16 x 1 1/2 (2 req'd w/dbl reduction) 3 P Chain #40 x 29 5 P Bearing ER12 6 P Key 1/8 x 1/2 Woodruff (2 req'd) 7 P Pillow block 3/4 (2 req'd) 8 P Transmission pulley 9 P Rod end F 10 P Rod end M 11 P Friction spring 12 P Trans. sprocket P Sprocket P Sprocket 40B P Sprocket 40B28 16 P Push button switch (2 req'd) 17 P Ball plunger 1/2 18 P Transmission fan 19 P Friction washer 20 P Wear strip x 8.75 (2 req'd) 21 P Wire harness 22 P Hyd. transmission 23 P Bearing housing 24 P Control mount 25 P Directional control arm 26 P Transmission frame 27 P Speed control arm 28 P Arm extension 29 P Jack shaft 30 P Bell crank 31 P Drive gear* 15T 32 P Gear shaft 33 P Linkage rod 34 P Switch mount 35 P Control cover 36 P Key 33/16 x I 37 P Foam Grip 38

10 Parts for Drive Assembly 39

11 Miscellaneous Parts ITEM PART # DESCRIPTION 1 P Air cleaner P Air filter element OUTER 2 P Muffler 35 WD-72 3 P Pre-cleaner (35 HP) 4 P Caster wheel 3 5 P Connection hose P Pulley 5/16 rope (2 reqd) 7 P /16 Nylon rope 8 P Handle grip 1 (2 req'd) 9 P Guide adjuster. 10 P Guide frame 11 P Rear line pointer 12 P Retractable handle 13 P Securing L bolt 3/8 14 P Guard plate 15 P Oil filter 35 (not shown) 16 P Lifting Bail 17 P Battery 12V (not shown) 18 P Fuel Tank (35 HP) (not shown) 19 P Decal Kit (not shown) 20 P Arbor Cover (not shown) 40

12 Parts for Night Light Assembly - Part # P ITEM PART DESCRIPTION 1 P Light 12V 2 P Light mount tube 3 P L Bolt.38 4 P Light mount bracket 5 P Switch Assembly 41