Vane motor high performance hydraulic series M5B - M5BS - M5BF

Size: px
Start display at page:

Download "Vane motor high performance hydraulic series M5B - M5BS - M5BF"

Transcription

1 Vane motor high performance hydraulic series M5B - M5BS - M5BF Publ. 2 - AM172 - B 1 / 25 / FB Replaces : 2 - AM172 - A L

2 CHARACTERISTICS - M5B* SERIES LOW NOISE MOTOR 12 vanes and a patented cartridge design allow a very low noise level, whatever the speed. HIGH PERFORMANCE MOTOR The M5B series has been designed especially for severe duty applications wich require high pressure, high speed and low fluid lubricity. Max. pressure (intermittent) M5B* 12 to 36: 465 PSI M5B* 45 : 46 PSI Max. speed (intermittent, low loaded cond.) M5B* : 6 RPM M5B* : 4 RPM M5B* 45 : 3 RPM HIGH EFFICIENCY Up to 9 % overall at 465 PSI. Vane motors begin life with a high volumetric efficiency, and maintain that efficiency throughout their operating life. Vane pin holdout design improves the mechanical efficiency at low pressure. HIGH STARTING TORQUE The high starting torque efficiency of the vane type motors allows them to start under high load without pressure overshoots, jerks and high instantaneous horsepower loads. LOW TORQUE RIPPLE This 12 vane type motor exhibits a very low torque ripple (typical ± 1,5%), even at low speeds. HIGH LIFETIME The vane, rotor and cam ring are pressure balanced to increase life over the full speed range. Double lip vanes reduce the sensitivity to fluid pollution. INTERCHANGEABLE ROTATING GROUPS Our precise manufacturing allows any component to be interchangeable. Rotating groups may be easily replaced to renew the motor or change the displacement to suit altered requirements for speed or torque. ROTATION AND DRAIN The M5B-M5BS are bi-directional motors, externally drained. The M5BF, externally drained, is available in three types of rotation : bi-directional, clockwise, counter-clockwise. The M5BF1, internally drained, is available in two types of rotation : clockwise, and counter-clockwise. CROSS PORT CHECK VALVE MOUNTING The uni-directional M5BF and M5BF1 are designed with an internal valve that allows smooth dynamic braking, with a very simple hydraulic circuit and without risk of motor cavitation. M5B - M5BS : Cylindrical keyed or splined shaft according to SAE J744, ISO or J498b. These products are designed primarily for coaxial drives which do not impose axial or side loading on the shaft. M5BF : A stiff taper or cylindrical keyed shaft and a high load capacity double ball bearing allow the direct mounting on shaft (fan,...). M5B M5BS M5BF. Mounting flange Ports Drain Shaft ends ISO A2/B4 HW SAE 3/4" M18 x.6 (2/4 bolts DIA) 4 bolts SAE "B" J744c UNC or (2/4 bolts - 4. DIA) metric threads M18 x.6 (ISO/DIS 6162 or SAE J518c) SAE 9/16" Special mounting (2 bolts DIA) Keyed cyl. SAE "B" or Keyed cyl. ISO E 25M or Splined SAE "B" Keyed taper non SAE Keyed cyl. SAE "C" Keyed cyl. ISO G32N 2

3 DESCRIPTION - M5B* SERIES The cartridge is a replaceable assembly including the cam ring, rotor, vanes, pins and springs. The floating side plate contains a shuttle valve which passes a higher pressure signal to the clamping area. M5BF M5B - M5BS The side feed holes supply inlet pressure to pin cavity. Port A ramp where unloaded vane moves outward for CW rotation Major arc where fluid works to push vane. The vane is urged outward by the pin force, spring force and centrifugal force. Minor arc where vane works to seal inlet pressure from outlet port. Port B ramp unloaded vane moves inward for CW rotation. The rotation is changed by reversing the flow. The cam ring is interchangeable with others of different displacement. It has lub coating on inner surface. The rotor is of through-hardened high alloy steel. The side grooves and radial holes cause undervane and overvane pressure to be equal. The pin cavity is at a steady pressure equal to that at inlet port. Section A-A OPERATION - SINGLE CARTRIDGE The motor shaft is driven by the rotor. Vanes, closely fitted into the rotor slots move radially to seal against the cam ring. The ring has two major and two minor radial sections joined by transitional sections called ramps. These contours and the pressures exposed to them are balanced diametrically. Hydraulic pins and light springs urge the vanes radially against the cam contour assuring a seal at zero speed so that the motor can develop starting torque. The springs and pins are assisted by centrifugal force at higher speeds. Radial grooves and holes through the vanes equalize radial hydraulic forces on the vanes at all times. Fluid enters and leaves the motor cartridge through opening in the side plates at the ramps. Each motor port connects to two diametrically opposed ramps. Pressurized fluid entering at Port A torques the rotor clockwise. The rotor transports it to the ramp openings which connect to Port B from which it returns to the low pressure side of the system. Pressure at Port B torques the rotor counter-clockwise. The rotor is separated axially from the sideplate surfaces by the fluid film. The front sideplate is clamped against the cam ring by the pressure, maintains optimum clearance as dimensions change with temperature and pressure. A 3-way shuttle valve in the sideplate causes clamping pressure in Port A or B, whichever is the highest. Materials are chosen for long life efficiency. The vanes, rotor and cam ring are made out of hardened high alloy steels. Cast semi-steel sideplates are chemically etched to have a fine crystalline surface for good lubrication at start-up. 3

4 PORTS AND HYDRAULIC FLUIDS - M5B* SERIES EXTERNAL DRAIN MOTOR This motor may be alternately pressurized on ports A and B to 465 PSI max. Whichever port is at low pressure, it should not be subjected to more than 6% of the high pressure, eg : When 465 PSI in A, B is limited to 29 PSI. This motor must have a drain line connected to the center housing drain connection of sufficient size to prevent back pressure in excess of 5 PSI, and returned to the reservoir below the surface of the oil as far away as possible from the suction pipe of the pump. INTERNAL DRAIN MOTOR RECOMMENDED FLUIDS FIRE RESISTANT FLUIDS ACCEPTABLE ALTERNATE FLUIDS This unidirectional motor may be pressurized only on the port corresponding to its rotation type. The outlet pressure must not be higher than 5 PSI. Petroleum base anti-wear R & O fluids (covered by DENISON HF- and HF-2 specifications). Maximum catalog ratings and performance data are based on operation with these fluids. They are easily used in the M5B* motor. These include phosphate or organic ester fluids and blends, water-glycol solutions and water-oil invert emulsions. The use of fluids other than petroleum base anti-wear R & O fluids requires that the maximum ratings of the motor will be reduced. In some cases, the minimum replenishment pressure must be increased. HF-1 : non antiwear petroleum base. HF-3 : water in oil emulsion. HF-4 : water glycols. HF-5 : synthetic fluids. Max. press. int. : 35 PSI (HF-1, HF-4, HF-5) 25 PSI (HF-3) Max. press. cont. : 3 PSI (HF-1, HF-4, HF-5) 2 PSI (HF-3) Max. speed : 18 RPM (HF-3, HF-4, HF-5) VISCOSITY VISCOSITY INDEX TEMPERATURE FLUID CLEANLINESS WATER CONTAMINATION IN FLUID Max. (cold start, low speed and pressure) 4 SUS Max. (full speed and pressure) 5 SUS Optimum (max. lifetime) 14 SUS Min. (full speed and pressure, HF-1 fluid) 9 SUS Min. (full speed and pressure, HF- & HF-2 fluids) 6 SUS For cold starts, the motor should operate at low speed and pressure until fluid warms up to an acceptable viscosity for full power operation. 9 min. Higher values extend the range of operating temperatures and lifetime. Max. fluid temperature (HF-, HF-1 & HF-2) F Min. fluid temperature (HF-, HF-1 &HF-2) -.4 F The fluid must be cleaned before and during operation to maintain a contamination level of NAS 1638 class 8 (or ISO 18/14) or better. Filters with 25 micron (or better, ß1 1) nominal ratings may be adequate but do not guarantee the required cleanliness levels. Maximum acceptable content of water is :,1 % for mineral base fluids,5 % for synthetic fluids, crankcase oils, biodegradable fluids. If amount of water is higher, then it should be drained off the circuit. MINIMUM REPLENISHMENT PRESSURE (PSI ABSOLUTE) Speed [RPM] - Oil viscosity = 15 SUS M5B* The inlet port of the motor must be supplied with replenishment pressure as listed above to prevent cavitation during dynamic braking. This pressure should be multiplied by a coefficient of 1,5 when used with fire resistant fluids (HF-3, HF-4, HF-5). 4

5 MOTOR SELECTION - M5B* SERIES Motor performances required Torque T [in.lbf] 97 Speed n [RPM] 15 Pump available data Flow q Ve [GPM] Check if available power is greater than required power (.85 estimated overall efficiency). q Ve xp.85 x Txn 14.5 x x x > 23.1 HP Two ways of calculation : Calculate V i from T required torque, or from q Ve available flow 2a. V i = 2 π x T = p 2 π x 97 = 1.5 in 3 rev. 46 3a. Choose motor from V i immediately greater M5B* 28 : V i = 1.71 in 3 /rev. 4a. Check theoretical motor pressure p = 2 π x T = 2 π x 97 = 356 PSI V i 1.71 Torque loss at this pressure = 85 in.lbf (See page 6) Calculate real pressure 2 π x (T + Tl) p = = V i 2 π x 155 = 388 PSI a. Flow loss at this pressure : 1.3 GPM (See page 6) Real flow used by the motor : = 13.2 GPM 6a. Real speed of the motor : qv x x 231 n = = = 178 RPM V i b. V i = 231 xq Ve = n 231 x 14.5 = 2.23 in 3 rev. 15 3b. Choose motor from V i immediately smaller M5B* 36 : V i = 2.2 in 3 /rev. 4b. Check theoretical motor press. with T = 97 in.lbf p = 2 π x T = 2 π x 97 = 277 PSI V i 2.2 Torque loss at this pressure = 7 in.lbf (See page 6) Calculate real pressure 2 π x (T + Tl) p = = V i 2 π x 14 = 297 PSI 2.2 5b. Flow loss at this pressure : 1.1 GPM (See page 6) Real flow used by the motor : = 13.4 GPM 6b. Real speed of the motor : qv x x 231 n = = = 141 RPM V i 2.2 Real performances V i = 1.71 in 3 /rev. n = 178 RPM T = 97 in.lbf p = 388 PSI Real performances V i = 2.2 in 3 /rev. n = 141 RPM T = 97 in.lbf p = 297 PSI In each case always choose the smallest motor which will operate at the highest speed and pressure, and will offer the most efficient solution. FLUID POWER FORMULAS Volumetric efficiency Mechanical efficiency Fluid motor speed RPM 1 total leakage x speed x displacement 1 torque loss x 2 π Δ pressure x displacement 231 x flow rate displacement x volumetric eff. Speed Displacement Δ pressure Flow rate Leakage Torque Torque loss [RPM] [in 3 /rev] [PSI] [GPM] [GPM] [in.lbf] [in.lbf] Fluid motor torque Fluid motor power in.lbf HP HP Δ pressure x displacement xmech. eff. 2 π speedx displacementx Δ pressure x overall eff torque xspeed 63 5

6 PERFORMANCE DATA - M5B* SERIES Series M5B* Cartridge Theoretical displacement Theoretical torque Theoretical power at 1 RPM Typical data 2 RPM PSI in 3 /rev in-lbf/psi HP/1 PSI in/lbf HP 12.73,116, ,175, ,272, ,35, ,437, ) ) OVERALL LEAKAGE (internal + external) Overall leakage qs [GPM] SUS 115 SUS TORQUE LOSS SUS 1 6 SUS 8 Torque T (in.lbf) LP NOISE M5BF - 36 Lp. Noise level [db(a)] 1m ISO RPM 15 RPM 75 1 RPM 5 RPM STARTING PERFORMANCES Typical data at 115 SUS / 113 F Maximum cross-flow 145 PSI :.47 GPM 29 PSI : 2.6 GPM 465 PSI : 3.3 GPM Minimum stalled torque efficiency 145 PSI : 78.3 % 29 PSI : 81. % 465 PSI : 8.8 % 6

7 MAX RATINGS - M5B* SERIES 12 & Intermittent Continuous Operating speed n [RPM] Kurzzeitig 5 Dauernd Operating speed n [RPM] Kurzzeitig Dauernd Operating speed n [RPM] - These are running condition limits ; for starting performances see page 6. - Intermittent conditions : do not exceed 6 seconds per minute of rotation. - Typical curves, at 115 SUS / 113 F. - For higher specifications or for operating speed under 1 RPM, please consult our technical department. 7

8 ORDERING CODE - M5B - M5BS SERIES Model No. M5B* N 2 - A 1 M 3 - Series M5B : Mounting flange ISO A2/B4HW Series M5BS : Mounting flange SAE "B" - J744 Cam ring Volumetric displacement 12 =.73 in 3 /rev 18 = 1.1 in 3 /rev 23 = 1.4 in 3 /rev 28 = 1.71 in 3 /rev 36 = 2.2 in 3 /rev 45 = 2.75 in 3 /rev Type of shaft 1 = keyed (SAE B - J744) 2 = keyed ( ISO E25M ) 3 = splined (SAE B - J498) 4 = splined (SAE BB - J498) Direction of rotation (view on shaft end) N = bi-directional Modifications Drain variables M5B : 3 = M18 x.6 metric drain M5BS : 2 = 9/16" SAE drain 3 = M18 x.6 metric drain Port variables = 3/4" SAE 4 bolts - J518c - UNC thread M =3/4" SAE 4 bolts - J518c - metric thread Seal class 1 = S1 BUNA N 5 = S5 VITON Design letter Porting combination See hereunder View from shaft end : CW rotation A = inlet B = outlet CCW rotation A = outlet B = inlet PERMISSIBLE AXIAL AND RADIAL LOADS Load F [Lbs] Speed n [RPM] 8

9 DIMENSIONS - Weight : 4.8 lbs - M5B - M5BS SERIES C D Ø E Port code Ø A Drain code Ø B C D Ø E F Ø G H J K Ø L M5BS M5B M M 3/8-16 UNC 2 SAE 9/ ,8 44,9 14,3 9,7 11,6 1,5 73, 146, 14,3 M1 3 M18 x 1,5 3/8-16 UNC M1 3 M18 x 1,5 88,4 44,2 11, 9, 1, 2, 7, 14, 14, D C K 6.85 J Ø L B M A KEY.248 / DIA MAXI Ø G H x 45.6 x 45 F.96.6 x 45 SHAFT CODE 3 SAE B INVOLUTE SPLINE DATA CLASS 1-FLAT ROOT SIDE FIT J498b - PITCH 16/32 13 TEETH - 3 PRESSURE ANGLE DIA ± MAX Ø G DRAIN PORT Ø B DEEP.53 MAX SPOT FACE Ø 29 DEEP.8 MAX.87 SHAFT CODE 1 KEYED SAE-B H x 45 F KEY x 45 SHAFT CODE 2 KEYED ISO E25M Ø B A MOUNTING TORQUE :.885 in.lbf Ø A DEEP.75 ( 8 PLACES ) x 45 SHAF AFT CODE 4 SAE BB INVOLUTE SPLINE DATA CLASS 1-FLAT ROOT SIDE FIT J498b - PITCH 16/32 15 TEETH - 3 PRESSURE ANGLE 9

10 ORDERING CODE - M5BF SERIES Model No. M5BF N 2 - A 1 M 3 - Series external drain Series internal drain Cam ring Volumetric displacement 12 =.73 in 3 /rev 18 = 1.1 in 3 /rev 23 = 1.4 in 3 /rev 28 = 1.71 in 3 /rev 36 = 2.2 in 3 /rev 45 = 2.75 in 3 /rev Type of shaft 1 = keyed taper (non SAE) 2 = keyed (SAE C - J744c) W = keyed (ISO G32N) Direction of rotation (view on shaft end) M5BF : N = bi-directional R = clockwise L = counter-clockwise M5BF1 : R = clockwise L = counter-clockwise Modifications Drain variables M5BF : 2 = 9/16" SAE drain 3 = M18 x.6 metric drain M5BF1 : X = no drain connection Port variables M5BF : = 3/4" SAE 4 bolts - J518c - UNC thread M =3/4" SAE 4 bolts - J518c - metric thread M5BF1 : M =3/4" SAE 4 bolts - J518c - metric thread Seal class 1 = S1 BUNA N 5 = S5 VITON Design letter Porting combination See hereunder PORTING COMBINATION ROTATIONS View from shaft end : CW rotation A = inlet B = outlet CCW rotation A = outlet B = inlet PERMISSIBLE AXIAL AND RADIAL LOADS 1 - Max. axial load : Fa max. = 135 lbs 2 - Max. radial load cylindrical shaft : Fr max. = 18 lbs taper shaft : Fr max. = 125 lbs 3 - Theoretical lifetime [hour] : L 1 H [Hour] = 4 - Theoretical lifetime [1 6 rev] : L N [rpm] x L Eg of theoretical life time calculation Axial load Fa = 45 lbs Radial load Fr = 225 lbs Operating speed N = 2 RPM L 1 = 2 [1 6 rev] (see on curve) L 1 H = 2 x 2 L 1H = hours. 1 Radial load Fr [lbs] L1= 25 L1= 5 L1= 1 L1=2 L1= Axial load Fa [lbs] 1

11 DIMENSIONS - Weight : 4.8 lbs - M5BF SERIES 1.97 KEY.392 / DIA DIA DIA 1.38 M16 x.6 * 2.12 ± DIA ±.1.25 KEY B A A -.75 DEEP ( 8 PLACES ).75 DIA DRAIN PORT Ø B -.53 DEEP MAX SPOT FACE 1.14 DIA -.8 DEEP MAX DIA DIA DIA.12 ± ± KEY.311 /.312 SHAFT CODE 2 SAE "C" - J744 WITH M1-2 DEEP 5.26 B A 5.4 R3.3 MOUNTING TORQUE : 885 in.lbf Ø SHAFT CODE 1 SAE "BB" - J 744 ( MODIFIED * ) WITH M16 TAPER 125:1 SHAFT CODE W ISO 319/2 - G32N WITH M1-2 DEEP Ø * This torque is for a steel coupling and a nut of at least grade 8.8 quality. It is compulsory to install a castle nut and cotter pin for right-hand rotation - bi-rotational. B DIA R2 Ø C Port code ØA Drain code ØB M5BF M5BF1 M M 3/8-16 UNC M1 M1 2 3 X SAE 9/16-18 M18 x 1,5 no drain connection L R1 125 ±.67 : 1 Torque of the nut : 8 Nm * Shaft DIA Ø C L Code 1 25,27/25,4 53,5/54,5 34,8/35,2 11

Vane motors Single & double zm21 M3B - M4 / M4S series

Vane motors Single & double zm21 M3B - M4 / M4S series Vane motors Single & double zm21 M3B - M4 / M4S series Publ. 2 - AM 157 - B 07 / 97 / FB Replaces : 2 - AM 157 - A CHARACTERISTICS - M3* AND M4* SERIES HIGH STARTING TORQUE EFFICIENCY HIGH VOLUMETRIC EFFICIENCY

More information

Vane motors Single & double M3B - M4 / M4S series

Vane motors Single & double M3B - M4 / M4S series Vane motors Single & double M3B - M4 / M4S series Publ. 2 - AM 157 - B 07 / 97 / FB Replaces : 2 - AM 157 - A CONTENTS - M3* AND M4* SERIES GENERAL General characteristics... 3 Technical data... 4 General

More information

Mobile Hydraulic Pumps T6G, T67G, T6ZC. Denison Vane Technology, fixed displacement

Mobile Hydraulic Pumps T6G, T67G, T6ZC. Denison Vane Technology, fixed displacement Mobile Hydraulic Pumps T6G, T67G, T6ZC Denison Vane Technology, fixed displacement aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing

More information

Vane pumps single, double & triple T6 mobile application zp20

Vane pumps single, double & triple T6 mobile application zp20 Vane pumps single, double & triple T6 mobile application zp20 Publ. 1 - AM0701 - A 11 / 98 / 2000 / FB Replaces : 1 - AM 075 - A FEATURES - T6 SERIES MOBILE APPLICATION GREATER FLOW HIGHER PRESSURE BETTER

More information

Vane pumps single, double & triple T6 mobile application zp20

Vane pumps single, double & triple T6 mobile application zp20 Vane pumps single, double & triple T6 mobile application zp20 Publ. 1 - AM0701 - A 11 / 98 / 2000 / FB Replaces : 1 - AM 075 - A FEATURES - T6 SERIES MOBILE APPLICATION GREATER FLOW HIGHER PRESSURE BETTER

More information

DENISON HYDRAULICS vane pumps - single, double, triple T6 mobile application.

DENISON HYDRAULICS vane pumps - single, double, triple T6 mobile application. DENISON HYDRAULICS vane pumps - single, double, triple T6 mobile application. Publ. 1 - AM0701 - A 11 / 98 / 2000 / FB Replaces : 1 - AM 075 - A CONTENTS - T6 SERIES MOBILE APPLICATION GENERAL Features...

More information

Hydraulic Motor M5A*/M5B* Series Vane Motors

Hydraulic Motor M5A*/M5B* Series Vane Motors Hydraulic Motor M5*/M5* Series Pressure up to 32 bar Fixed Displacement from 6 to 45 ml/rev. Catalogue HY29-18/UK December 26 Catalogue HY29-18/UK Content General M5* / M5* Warning... 2 General characteristics...

More information

KT6 Series Variable Displacement Vane Pumps

KT6 Series Variable Displacement Vane Pumps Care in Application 1. Check speed range, pressure, temperature, fluid quality, viscosity and pump rotation. 2. Check inlet conditions of the pump, if it can accept application requirment. 3. Type of shaft

More information

Hydraulic Pumps T7 for variable speed drives

Hydraulic Pumps T7 for variable speed drives FC Hydraulic Pumps T7 for variable speed drives Denison Vane Technology Catalogue HY29-11/UK Content General Information Introduction and product key features 3 Main Technical Data Main table for single

More information

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BV

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BV FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BV BV FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BV SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps.

More information

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BV SERIES

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BV SERIES BV FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BV SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained

More information

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps.

More information

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps.

More information

Industrial Hydraulic Pumps T7DBB, T7DBBS. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement

Industrial Hydraulic Pumps T7DBB, T7DBBS. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement Industrial T7DBB, T7DBBS Denison Vane Technology, fixed displacement Hydraulic Motors Hydraulic Valves Hydraulic Cylinders Hydraulic Filtration Hydraulic Accumalators We are doing our parts to keep you

More information

Vickers 45. VMQ Series 30 Vane Pumps. Fixed Displacement, For Industrial and Mobile Applications (4.188)

Vickers 45. VMQ Series 30 Vane Pumps. Fixed Displacement, For Industrial and Mobile Applications (4.188) [ (4.188) 49,4 (1.94) /21,8 /.86) 174,7/172,3 (6.88/6.78) 332,9/33,5 (13.11/13.1) "M" is marked if metric port threads No marking if inch port threads AS-568-152 O-ring Vickers 45 65,3 (2.57) 13 (5.1 VMQ

More information

Vickers. Vane Pumps. Double Thru-drive Vane Pumps. High speed, high pressure VQT Series for mobile equipment. Released 7/93

Vickers. Vane Pumps. Double Thru-drive Vane Pumps. High speed, high pressure VQT Series for mobile equipment. Released 7/93 Vickers Vane Pumps Double Thru-drive Vane Pumps High speed, high pressure VQT Series for mobile equipment Released 7/93 612 Introduction Double VQT high performance pumps are fixed displacement units that

More information

Vickers. Piston Motors. Inline Piston Motors. Fixed and Variable Displacement. Revised 5/99 691

Vickers. Piston Motors. Inline Piston Motors. Fixed and Variable Displacement. Revised 5/99 691 Vickers Piston Motors Inline Piston Motors Fixed and Variable Displacement Revised 5/99 691 Table of Contents Introduction........................................................................................

More information

Hydraulic Motors M3B - M4* Denison Vane Technology, fixed displacement

Hydraulic Motors M3B - M4* Denison Vane Technology, fixed displacement Hydraulic Motors M3B - M4* Denison Vane Technology, fixed displacement General Series M3B - M4*, Denison Vane Motors GENERAL M3B M4C - M4SC M4D - M4SD M4E - M4SE M4DC - M4SDC General characteristics...

More information

Vane Pumps. VMQ Series Vane Pumps For Industrial and Mobile Applications Displacements to 215 cm 3/ r (13.12 in 3 /r) Pressures to 260 bar (3800 psi)

Vane Pumps. VMQ Series Vane Pumps For Industrial and Mobile Applications Displacements to 215 cm 3/ r (13.12 in 3 /r) Pressures to 260 bar (3800 psi) Vickers Vane Pumps VMQ Series Vane Pumps For Industrial and Mobile Applications Displacements to 215 cm 3/ r (13.12 in 3 /r) Pressures to 260 bar (3800 psi) 5008.00/EN/0596/A A.25 Introduction From the

More information

HYDRAULIC MOTORS EPMT

HYDRAULIC MOTORS EPMT HYDRAULIC APPLICATION Conveyors; Metal working machines; Machines for agriculture; Road building machines; Mining machinery; Food industries; Special vehicles; Plastic and rubber machinery etc. CONTENTS

More information

Mobile Hydraulic Pumps T6DCM, T6DCP, T6DCMW. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement

Mobile Hydraulic Pumps T6DCM, T6DCP, T6DCMW. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement Mobile Hydraulic Pumps T6DCM, T6DCP, T6DCMW Denison Vane Technology, fixed displacement Hydraulic Pumps Hydraulic Motors Hydraulic Valves Hydraulic Cylinders Hydraulic Filtration Hydraulic Accumalators

More information

6000 Series Highlights

6000 Series Highlights Highlights Features 9 displacements available Presents a multitude of options that make this motor very smart and flexible to apply Benefits Very tough motor for demanding applications Can be used in a

More information

Vickers. Vane Pumps. V Series - Low Noise Vane Pumps High Performance Intravane Pumps For Industrial Applications.

Vickers. Vane Pumps. V Series - Low Noise Vane Pumps High Performance Intravane Pumps For Industrial Applications. Vickers Vane Pumps V Series - Low Noise Vane Pumps High Performance Intravane Pumps For Industrial Applications Revised 6/95 560 Introduction Vickers offers the most complete line of hydraulic intravane

More information

Instructions for Use and Repairs (DT61Series) Cartridge identification, change of rotation, guidelines for repairs

Instructions for Use and Repairs (DT61Series) Cartridge identification, change of rotation, guidelines for repairs SINGLE AND MULTIPLE VANE PUMPS & VANE MOTORS Introduction General Information BH* & V* General Information DT6* Single Vane Pumps BH*, V* and DT6* single vane pumps Thru Drive Single Vane Pumps V**T thru

More information

Disc Valve Hydraulic Motors 4000 Compact Series

Disc Valve Hydraulic Motors 4000 Compact Series Disc Valve Hydraulic Motors 10.2014 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.2014 EN EATON_Motoren english Port B Port A Features Shuttle Valve with Back- Pressure Relief Valve Highlights

More information

MINING FORESTRY MOBILE TRUCK AGRICULTURE MATERIAL HANDLING OPTIMUM

MINING FORESTRY MOBILE TRUCK AGRICULTURE MATERIAL HANDLING OPTIMUM MINING FORESTRY MOBILE TRUCK AGRICULTURE MATERIAL HANDLING OPTIMUM Muncie Power Products OPTIMUM Series gear pumps/motors offer premier performance for a wide variety of applications across several industries.

More information

Disc Valve Hydraulic Motors 2000 Series

Disc Valve Hydraulic Motors 2000 Series Disc Valve Hydraulic Motors 10.2014 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.2014 EN EATON_Motoren english Highlights Port A Features Three zone design for longer life and true bi-directionality.

More information

GM SERIES TECHNICAL CATALOG. Crankshaft Design Radial Piston Hydraulic Motors

GM SERIES TECHNICAL CATALOG. Crankshaft Design Radial Piston Hydraulic Motors www.saihyd.com info@saihyd.com Crankshaft Design Radial Piston Hydraulic Motors GM SERIES TECHNICAL CATALOG CONTENTS PAGE Motor Displacement Table 2 Motor Characteristics & Technical Data 3 GM05 Series

More information

FIXED DISPLACEMENT VANE PUMPS

FIXED DISPLACEMENT VANE PUMPS FIXED DISPLACEMENT VANE PUMPS Single Vane Pumps Double Vane Pumps Thru-Drive Vane Pumps HS - HQ - VH - SERIES Working pressure: up to 210 bar Displacements: from 3 cc to 200 cc Pumps, cartridges and spare

More information

6000 Series. Highlights C-5. Description With torque up to 15,000 in-lb and 40 gpm continuous, this motor is packed with power operates very smoothly.

6000 Series. Highlights C-5. Description With torque up to 15,000 in-lb and 40 gpm continuous, this motor is packed with power operates very smoothly. Highlights Features 9 displacements available Presents a multitude of options that make this motor very smart and flexible to apply Benefits Very tough motor for demanding applications Can be used in a

More information

Veljan Gear Pumps. E' Series Features:-

Veljan Gear Pumps. E' Series Features:- E' Series Features:- Heavy duty sleeve bushing design in a small frame size Displacements from 43.5cc/rev to 146.5cc/rev Working pressures up to 240bar Speeds up to 3500rpm Flows up to 38.7gpm High strength

More information

Gear Housing Widths 1.00" 1.25" 1.50" 1.75" 2.00" 2.25" 2.50" Gear Housing Widths / Flow Rate [ VGP - D Series ]

Gear Housing Widths 1.00 1.25 1.50 1.75 2.00 2.25 2.50 Gear Housing Widths / Flow Rate [ VGP - D Series ] 'D' Series Features:- Heavy duty sleeve bushing design in a small frame size Displacements from 20.6cc/rev to 104.2cc/rev Working pressures up to 240bar Speeds up to 3500rpm Flows up to 27.5gpm High strength

More information

Disc Valve Hydraulic Motors Series 6000

Disc Valve Hydraulic Motors Series 6000 Disc Valve Hydraulic Motors Series 6000 10.2014 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.2014 EN EATON_Motoren english Highlights Features 9 displacements available Presents a multitude

More information

Variable displacement axial piston pumps,

Variable displacement axial piston pumps, Variable displacement axial piston pumps, Edition: 04/04.2000 Replaces: 04/10.99 DISPLACEMENTS From To PRESSURE Max. continuous Max. intermittent Max. peak 29 cm 3 /rev 73 cm 3 /rev 280 bar 315 bar 350

More information

Series 20 Axial Piston Pumps. Technical Information

Series 20 Axial Piston Pumps. Technical Information Series 20 Axial Piston Pumps Technical Information General Description INTRODUCTION Sauer-Danfoss a world leader in hydraulic power systems has developed a family of axial piston pumps. DESCRIPTION Sauer-Danfoss

More information

Mobile Hydraulic Pumps T6DCCM. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement

Mobile Hydraulic Pumps T6DCCM. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement Mobile Hydraulic Pumps T6DCCM Denison Vane Technology, fixed displacement Hydraulic Pumps Hydraulic Motors Hydraulic Valves Hydraulic Cylinders Hydraulic Filtration Hydraulic Accumalators We are doing

More information

US version. Drain connection

US version. Drain connection Versions OMT Versions Mounting flange Standard flange Shaft Port size Europea n version US version Drain connection Check valve Low pressure release High pressure release Cyl. 4 mm G 3/4 X Yes Yes OMT

More information

Industrial Hydraulic Pumps T7E, T7ES. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement

Industrial Hydraulic Pumps T7E, T7ES. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement Industrial T7E, T7E Denison Vane Technology, fixed displacement Hydraulic Motors Hydraulic Valves Hydraulic Cylinders Hydraulic Filtration Hydraulic Accumalators We are doing our parts to keep you moving!

More information

HYDRAULIC MOTORS MLHH

HYDRAULIC MOTORS MLHH HYDRAULIC APPLICATION» Conveyors» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries» Mining machinery etc. CONTENTS Specification

More information

Series 20 Axial Piston Pumps. Technical Information

Series 20 Axial Piston Pumps. Technical Information Series 20 Axial Piston Pumps Technical Information General Description INTRODUCTION Sauer-Danfoss a world leader in hydraulic power systems has developed a family of axial piston pumps. DESCRIPTION Sauer-Danfoss

More information

PVX-11 VANE PUMPS. See pages 12 thru 14 for PVX-11 dimensions. VARIABLE DISPLACEMENT, PRESSURE COMPENSATED PERFORMANCE SPECIFICATIONS

PVX-11 VANE PUMPS. See pages 12 thru 14 for PVX-11 dimensions. VARIABLE DISPLACEMENT, PRESSURE COMPENSATED PERFORMANCE SPECIFICATIONS PVX-11 VANE PUMPS VARIABLE DISPLACEMENT, COMPENSATED NOTE: See pages thru 14 for PVX-11 dimensions. PERFORMANCE SPECIFICATIONS Displacement (Nominal) 1.5 in 3 /rev. (25 cm 3 /rev.) Displacement (Actual)

More information

HYDRAULIC MOTORS EPMS - series 3

HYDRAULIC MOTORS EPMS - series 3 HYDRAULIC EPMS - series APPLICATION» Conveyors» Metal working machine» Machines for agriculture» Road building machines» Mining machinery» Food industries» Special vehicles etc. CONTENTS Specification

More information

» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries

» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries HYDRAULIC HW APPLICATION» Conveyors» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries» Grass cutting machinery etc. CONTENTS

More information

HPVR-10 AXIAL PISTON PUMPS

HPVR-10 AXIAL PISTON PUMPS The HPVR series of inline axial piston variable displacement pumps, are available in five displacements and three compact frame sizes. These pumps feature medium-high working pressure capabilities that

More information

HYDRAULIC MOTORS EPMS

HYDRAULIC MOTORS EPMS HYDRAULIC EPMS APPLICATION» Conveyors;» Metal working machines;» Machines for agriculture;» Road building machines;» Mining machinery;» Food industries;» Special vehicles etc. CONTENTS Specification data...

More information

Disc Valve Hydraulic Motors Series 4000

Disc Valve Hydraulic Motors Series 4000 Disc Valve Hydraulic Motors Series 0 10.20 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.20 EN EATON_Motoren english Highlights Features 10 displacements, a variety of mounting flanges

More information

HPV-15 AXIAL PISTON PUMPS

HPV-15 AXIAL PISTON PUMPS SPECIFICATIONS Variable Displacement, Pressure Compensated OVERALL EFFICIENCY EFFICIENCY - % 1 9 8 7 6 bar 34 69 13 138 172 27 241 TYPICAL PERFORMANCE SPECIFICATIONS VOLUMETRIC cu. in./rev. 2.9 DISPLACEMENT

More information

Catalog HY /NA. Catalog HY /NA. Parker Hannifin Corporation Hydraulic Pump Division Marysville, Ohio USA

Catalog HY /NA. Catalog HY /NA. Parker Hannifin Corporation Hydraulic Pump Division Marysville, Ohio USA Catalog HY28-6/NA PV, PVT Series Piston Pumps Variable Volume Catalog HY28-6/NA 1 Catalog HY28-6/NA Notes Series PV 2 Catalog HY28-6/NA Introduction Series PV Quick Reference Data Chart Pump Delivery Approx.

More information

Kawasaki Motors Corp., U.S.A. Precision Machinery Division HMC 045. Staffa Fixed Displacement Hydraulic Motor

Kawasaki Motors Corp., U.S.A. Precision Machinery Division HMC 045. Staffa Fixed Displacement Hydraulic Motor Kawasaki Motors Corp., U.S.A. Precision Machinery Division HMC 045 Staffa Fixed Displacement Hydraulic Motor CONTENTS Page 1. General Description... 2 2. Functional Symbols... 2 3. Model Code... 3 4. Performance

More information

10,000 Series. Highlights C-6

10,000 Series. Highlights C-6 Highlights Features higher flows Benefits demanding mobile and industrial applications from Applications Description This is the biggest disc valve motor of our line with up to 45 GPM and 24,000 in-lb

More information

OMS Technical Information. Versions OMS. Versions

OMS Technical Information. Versions OMS. Versions Versions Versions Mounting flange Shaft Port size European version US version Drain connection Check valve Main type designation Yes Yes Yes Yes Yes Yes Standard Yes Yes Yes Yes Yes Yes P.t.o. Yes Yes

More information

SCM M2. Other advantages:

SCM M2. Other advantages: Sunfab s SCM 025-108 M2 is a range of robust axial piston motors with cartridge flange especially suitable for winch-, slewing-, wheel- and track drives. SCM 025-108 M2 is of the bent-axis type with spherical

More information

SCM SAE. Other advantages: Sunfab s SCM SAE is a range of robust axial piston motors especially suitable for mobile hydraulics.

SCM SAE. Other advantages: Sunfab s SCM SAE is a range of robust axial piston motors especially suitable for mobile hydraulics. Sunfab s SCM 010-130 SAE is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 SAE is of the bent-axis type with spherical pistons. The design results in a compact

More information

Veljan Gear Pumps. 'B' Series Features:

Veljan Gear Pumps. 'B' Series Features: '' Series Features: Self-priming pumps Heavy duty sleeve bushing design in a small frame size Displacements from 9.8cc/rev to 39.9cc/rev Working pressures up to bar Speeds up to rpm Flows up to 10.5gpm

More information

PowrFlow PVX Vane Pumps

PowrFlow PVX Vane Pumps PowrFlow PVX Vane Pumps POWRFLOW PVX VANE PUMPS YOUR SOURCE FOR VANE PUMPS FOR THE MOST DEMANDING APPLICATIONS What Makes PowrFlow PVX Vane Pumps Your Best Buy? Continental Hydraulics PowrFlow PVX Vane

More information

Disc Valve Hydraulic Motors

Disc Valve Hydraulic Motors Disc Valve Hydraulic Motors State of the art motors benefiting from years of experience and inovating constantly to fit your demands. C-i Disc Valve Hydraulic Motors Highlights Product Description In the

More information

HPV-15 AXIAL PISTON PUMPS

HPV-15 AXIAL PISTON PUMPS SPECIFICATIONS Variable Displacement, Pressure Compensated OVERALL EFFICIENCY EFFICIENCY - % 100 90 80 70 60 bar 0 34 69 103 138 172 207 241 TYPICAL PERFORMANCE SPECIFICATIONS VOLUMETRIC cu. in./rev. 2.09

More information

OMP Hydraulic Motor Versions

OMP Hydraulic Motor Versions Versions VERSIONS Mounting flange Shaft Port size European version US version Side port version End port version Flange port version G 1 /2 X X X No No OMP Cyl. 25 mm G 1 /2 X X X Yes No OMP G 1 /2 X X

More information

Kawasaki Motors Corp., U.S.A. Precision Machinery Division. Staffa Fixed Displacement Hydraulic Motor

Kawasaki Motors Corp., U.S.A. Precision Machinery Division. Staffa Fixed Displacement Hydraulic Motor Kawasaki Motors Corp., U.S.A. Precision Machinery Division HM(HD)B 270 Staffa Fixed Displacement Hydraulic Motor CONTENTS Page 1. General Description... 2 2. Functional Symbols... 2 3. Model Code... 3

More information

Mobile Hydraulic Pumps T6EM, T6EP. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement

Mobile Hydraulic Pumps T6EM, T6EP. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement Mobile Hydraulic Pumps T6EM, T6EP Denison Vane Technology, fixed displacement Hydraulic Pumps Hydraulic Motors Hydraulic Valves Hydraulic Cylinders Hydraulic Filtration Hydraulic Accumalators We are doing

More information

IFP VTM42 POWER STEERING PUMPS

IFP VTM42 POWER STEERING PUMPS IFP VTM42 POWER STEERING PUMPS * Compact Power Source for Steering Assemblies * Integral Relief and Flow Control * High Efficiency * Balanced Cartridge Design * Quiet Operation IFP Power Steering Pump

More information

5.2 MEDIUM HEAVY DUTY SERIES SIZE 3

5.2 MEDIUM HEAVY DUTY SERIES SIZE 3 .2 MEDIUM HEAVY DUTY SERIES SIZE 3 CONTENTS PGI101 Ordering Code.2.1 Medium Heavy Duty Series Technical Information.2.2 Specifications.2.3 Hydraulic fluids.2.4 Viscosity range.2. Temperature range.2.6

More information

Catalog PowrFlowTM PVX Vane Pumps

Catalog PowrFlowTM PVX Vane Pumps Catalog PowrFlowTM PVX Vane Pumps Your source for vane pumps for the most demanding applications. What Makes PowrFlow PVX Vane Pumps Your Best Buy? Continental Hydraulics PowrFlow PVX Vane Pumps deliver

More information

Kawasaki Motors Corp., U.S.A. Precision Machinery Division HMB 325. Staffa Fixed Displacement Hydraulic Motor

Kawasaki Motors Corp., U.S.A. Precision Machinery Division HMB 325. Staffa Fixed Displacement Hydraulic Motor Kawasaki Motors Corp., U.S.A. Precision Machinery Division HMB 325 Staffa Fixed Displacement Hydraulic Motor CONTENTS Page 1. General Description... 2 2. Functional Symbols... 2 3. Model Code... 3 4. Performance

More information

THRU DRIVE HYDRAULIC VANE PUMP TQ/TV SERIES

THRU DRIVE HYDRAULIC VANE PUMP TQ/TV SERIES THRU DRIVE HYDRAULIC VANE PUMP TQ/TV SERIES TQ/TV THRU-DRIVE HYDRAULIC VANE PUMPS TQ/TV SERIES Thru-drive pumps save installation space and cost by eliminating double shaft extension electric motors or

More information

Kawasaki Motors Corp., U.S.A. Precision Machinery Division HMB 100. Staffa Fixed Displacement Hydraulic Motor

Kawasaki Motors Corp., U.S.A. Precision Machinery Division HMB 100. Staffa Fixed Displacement Hydraulic Motor Kawasaki Motors Corp., U.S.A. Precision Machinery Division HMB 100 Staffa Fixed Displacement Hydraulic Motor CONTENTS Page 1. General Description... 2 2. Functional Symbols... 2 3. Model Code... 3 4. Performance

More information

Hydraulic Motor/Pump Series F11/F12 zp12

Hydraulic Motor/Pump Series F11/F12 zp12 Hydraulic Motor/Pump zp12 Fixed Displacement zp11 Catalogue HY17-8249/US March 2004 Conversion factors 1 kg... 2.20 lb 1 N... 0.225 lbf 1 Nm... 0.738 lbf ft 1 bar...14.5 psi 1 l...0.264 US gallon 1 cm

More information

RA / Radial Piston Motor Model MR, MRE Fixed Displacement. Table of Contents. Replaces: RA /10.95

RA / Radial Piston Motor Model MR, MRE Fixed Displacement. Table of Contents. Replaces: RA /10.95 Radial Piston Motor Model MR, MRE Fixed Displacement Sizes 160 to 9500 6100 PSI (up to 420 bar) 582 in 3 (up to 9542 cm 3 ) 25,075 lb-ft (up to 34000 Nm) RA 15 228/10.95 Replaces: 12.94 Wide range of displacements

More information

HPV-10 AXIAL PISTON PUMPS

HPV-10 AXIAL PISTON PUMPS SPECIFICATIONS Variable Displacement, Pressure Compensated OVERALL EFFICIENCY EFFICIENCY - % 1 9 8 7 6 bar 34 69 13 138 172 27 241 TYPICAL PERFORMANCE SPECIFICATIONS VOLUMETRIC cu. in./rev. 1.26 DISPLACEMENT

More information

1500 Series. Roller Bearing Gear Pumps and Motors (Bi-Rotational) High Performance Features: Hydreco

1500 Series. Roller Bearing Gear Pumps and Motors (Bi-Rotational) High Performance Features: Hydreco Roller Bearing Gear Pumps and Motors (Bi-Rotational) High Performance Features: The 1500K Series Pump/Motor utilizes the many design and application features of the widely accepted HYDRECO Series modern

More information

Series TMM Axial Piston Motor. Technical Information

Series TMM Axial Piston Motor. Technical Information Series TMM Axial Piston Motor Technical Information General Description GENERAL DESCRIPTION These motors are designed primarily to be combined with other products in closed circuit systems to transfer

More information

HYDRAULIC MOTORS HP APPLICATION GENERAL. » Conveyors» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines

HYDRAULIC MOTORS HP APPLICATION GENERAL. » Conveyors» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines HYDRAULIC HP APPLICAION» Conveyors» Feeding mechanism of robots and manipulators» Metal working machines» extile machines» Agricultural machines» Food industries» Grass cutting machinery etc. CONENS Specification

More information

Quality Products for Mechanical & Fluid Power. TQ & TV Series VANE PUMPS

Quality Products for Mechanical & Fluid Power. TQ & TV Series VANE PUMPS 1 Quality Products for Mechanical & Fluid Power 1 TQ & TV Series VANE PUMPS TQ/TV THRU-DRIVE HYDRAULIC VANE PUMPS TQ/TV SERIES Thru-drive pumps save installation space and cost by eliminating double shaft

More information

HEAVY DUTY HYDRAULIC MOTORS

HEAVY DUTY HYDRAULIC MOTORS HEAVY DUTY HYDRAULIC MTRS CNTENTS Page Hydraulic Motors Series MSWM... 4 Hydraulic Motors Series MTK... 8 Hydraulic Motors Series MTM... 17 Hydraulic Motors Series TMF... 9 Hydraulic Motors Series MVM...

More information

SCM SAE. Other advantages: Sunfab s SCM SAE is a range of robust axial piston motors especially suitable for mobile hydraulics.

SCM SAE. Other advantages: Sunfab s SCM SAE is a range of robust axial piston motors especially suitable for mobile hydraulics. Sunfab s SCM 010-130 SAE is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 SAE is of the bent-axis type with spherical pistons. The design results in a compact

More information

Gear Pumps. Series PGP Fixed Displacement Pumps, Cast-Iron Designs

Gear Pumps. Series PGP Fixed Displacement Pumps, Cast-Iron Designs Gear Pumps Series PGP Fixed Displacement Pumps, Cast-Iron Designs aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Table

More information

VARIABLE DISPLACEMENT AXIAL PISTON PUMPS

VARIABLE DISPLACEMENT AXIAL PISTON PUMPS VARIABLE DISPLACEMENT AXIAL PISTON PUMPS FEATURES Variable displacement axial piston pumps swash plate design ideally suited for medium and high pressure open circuit applications. The compact design allows

More information

Fixed Displacement Motor AA2FM (A2FM)

Fixed Displacement Motor AA2FM (A2FM) Fixed Displacement Motor 2FM (2FM) Series 6, for Open and Closed Circuits xial Piston, ent xis Design 5800 psi 6500 psi rueninghaus Hydromatik Sizes 5 1000 Nominal Pressure up to Peak Pressure up to (400

More information

VIS (Valve-In-Star) Hydraulic Motor

VIS (Valve-In-Star) Hydraulic Motor VIS (Valve-In-Star) Hydraulic Motor VIS 30 Series VIS 40 Series VIS 45 Series The next step in the evolution of low speed high torque (LSHT) hydraulic motors. EATON Low Speed High Torque Motors E-MOLO-MC001-E5

More information

UŽSISAKYKITE internetu telefonu el. paštu

UŽSISAKYKITE internetu  telefonu el. paštu Features Axial piston pump MA10VO in swashplate design is used in open loop circuits. Flow is proportional to drive speed and displacement. By adjusting the position of the swashplate it is possible to

More information

» Feeding mechanism of robots and manipulators;» Metal working machines;» Textile machines;» Machines for agriculture;» Food industries;

» Feeding mechanism of robots and manipulators;» Metal working machines;» Textile machines;» Machines for agriculture;» Food industries; HYDRAULIC HYDRAULIC APPLICATION» Conveyors;» Feeding mechanism of robots and manipulators;» Metal working machines;» Textile machines;» Machines for agriculture;» Food industries;» Grass cutting machinery

More information

Vickers. Vane Pumps. Single and Double Vane Pumps. Model Series V10, V20, V2010, and V2020 for Industrial Equipment.

Vickers. Vane Pumps. Single and Double Vane Pumps. Model Series V10, V20, V2010, and V2020 for Industrial Equipment. Vickers Vane Pumps Single and Double Vane Pumps Model Series V10, V20, V2010, and V2020 for Industrial Equipment Revised 1/95 698 Introduction Series V10, V20, V2010, and V2020 fixed displacement pumps

More information

Variable displacement axial piston pumps,

Variable displacement axial piston pumps, ariable displacement axial piston pumps, for open circuit DISPLACEMENTS From To 2.75 in 3 /rev (45 cm 3 /rev) 5.12 in 3 /rev (84 cm 3 /rev) MAX SPEED 3000 min -1 PRESSURE Max. continuous Max. intermittent

More information

OMEW Hydraulic Motor Versions

OMEW Hydraulic Motor Versions Versions VERSIONS Mounting flange Wheel Shaft Port size European version US version Clockwise shaft rotation (CW version) 1) Counter clockwise shaft rotation (CCW version) 1) Tapered 35 mm G 1 /2 X X X

More information

SPECIAL HYDRAULIC MOTORS AND MOTOR-BRAKES

SPECIAL HYDRAULIC MOTORS AND MOTOR-BRAKES SPECIAL HYDRAULIC AND MTRBRAKES CNTENTS Page Hydraulic Motors Series HP... Hydraulic Motors Series HR...11 Hydraulic Motors Series MLHRW...1 Hydraulic Motors Series...2 Hydraulic Motorbrakes Series BHR...3

More information

J Series (129-) Highlights

J Series (129-) Highlights Highlights Features: Constant clearance Geroler set Integrated check valves Thrust Bearing Bushing Port B Port A Self-lubricating shaft bushing High-strength rigid components Increased valve seal lands

More information

SCM ISO. SCM ISO is a range of robust axial piston motors especially suitable for mobile hydraulics.

SCM ISO. SCM ISO is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 ISO is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 ISO is of the bent-axis type with spherical pistons. The design results in a compact motor

More information

Solutions. We Manufacture. H y d r a u l i c s. Eaton Medium Duty Piston Pump. h y d r a u l i c s

Solutions. We Manufacture. H y d r a u l i c s. Eaton Medium Duty Piston Pump. h y d r a u l i c s H y d r a u l i c s ydraulics Eaton Medium Duty Piston Pump h y d r a u l i c s Model 70122, 70422, 70423, and 70523 or -Flow Compensated Piston Pumps We Manufacture April 1997 Solutions S o l u t i o

More information

Spool Valve Hydraulic Motors. Spool Valve motors incorporate the proven orbit motor principle to provide high torque at low speeds.

Spool Valve Hydraulic Motors. Spool Valve motors incorporate the proven orbit motor principle to provide high torque at low speeds. Spool Valve Hydraulic Motors Spool Valve motors incorporate the proven orbit motor principle to provide high torque at low speeds. B-i Spool Valve Motors Highlights Product Description Char-Lynn spool

More information

Variable displacement axial piston pumps,

Variable displacement axial piston pumps, LVP 04 T E Variable displacement axial piston pumps, Edition: 04/04.2000 Replaces: 04/10.99 DISPLACEMENTS From To PRESSURE Max. continuous Max. intermittent Max. peak 29 cm 3 /rev 73 cm 3 /rev 280 bar

More information

VHO Vane Pumps ENGINEERING DATA. Single, Double, Triple & Thru Drive Available Multiple Displacements Low Cost Alternative Proven Performance

VHO Vane Pumps ENGINEERING DATA. Single, Double, Triple & Thru Drive Available Multiple Displacements Low Cost Alternative Proven Performance ENGINEERING DATA VHO Vane Pumps Single, Double, Triple & Thru Drive Available Multiple Displacements Low Cost Alternative Proven Performance www.fluidynefp.com Table of Contents Performance Data...2 Model

More information

MOTOR SCM ISO

MOTOR SCM ISO MOTOR SCM 012-130 ISO SCM 012-130 ISO is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 012-130 ISO is of the bent-axis type with spherical pistons. The design results

More information

HYDRAULIC OIL PUMPS AND MOTORS PRODUCT CATALOG. Hybel - Hydraulic Oil Pumps and Motors

HYDRAULIC OIL PUMPS AND MOTORS PRODUCT CATALOG. Hybel - Hydraulic Oil Pumps and Motors HYDRAULIC OIL PUMPS AND MOTORS PRODUCT CATALOG Hybel Hydraulic Oil Pumps and Motors HYDRAULIC OIL PUMPS AND MOTORS Contents CONTENTS About us.... 04 Products Line.... 06 Configure your product.... 08 Aluminibeta

More information

Gear Motors. Series PGM Fixed Displacement Motors, Aluminium Designs

Gear Motors. Series PGM Fixed Displacement Motors, Aluminium Designs Gear Motors Series PGM Fixed Displacement Motors, Aluminium Designs aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding

More information

» Feeding mechanism of robots and manipulators;» Metal working machines;» Textile machines;» Machines for agriculture;» Food industries;

» Feeding mechanism of robots and manipulators;» Metal working machines;» Textile machines;» Machines for agriculture;» Food industries; HYDRAULIC APPLICATION» Conveyors;» Feeding mechanism of robots and manipulators;» Metal working machines;» Textile machines;» Machines for agriculture;» Food industries;» Grass cutting machinery etc. CONTENTS

More information

Hydraulic Pump T7AS/T7ASW Series Vane Pumps

Hydraulic Pump T7AS/T7ASW Series Vane Pumps Hydraulic ump T7A/T7AW eries Vane umps ressure up to 3 bar Fixed Displacement from 6 to 4 ml/rev. Catalogue HY29-8/UK April 26 Catalogue HY29-8/UK General Characteristics General T7A T7AW Vane umps T7A

More information

CONTINENTAL HYDRAULICS PVER VANE PUMPS

CONTINENTAL HYDRAULICS PVER VANE PUMPS CONTINENTAL HYDRAULICS PVER VANE PUMPS 5505 WEST 123RD STREET SAVAGE, MN 55378-1299 / PH: 952.895.6400 / WWW.CONTINENTALHYDRAULICS.COM PVER PUMPS FEATURES AND BENEFITS The PVER series vane pumps are variable

More information

OMEW Standard and with Low Speed Option. Orbital Motors. Technical Information

OMEW Standard and with Low Speed Option. Orbital Motors. Technical Information Standard and with Low Speed Option Orbital Motors Technical Information Contents Revision History Table of Revisions Date Page Changed Rev Jan 2009 Many major change BA Mar 2010 16 Japan location BB Contents

More information

1. Axial Piston Pumps

1. Axial Piston Pumps Axial Piston Pumps 1. Axial Piston Pumps Series Model Maximum Operating Pressure Maximum Displacement Remarks Page PSI In 3 /rev PV & PVM & PVR Premier Worldcup Goldcup PV6 4500 0.88 PV10 4500 1.26 PV15

More information

Torque. Motor model R

Torque. Motor model R MA series motors CHARACTERISTICS OF THE MA SERIES MOTORS (SAE Motor model Displacement Continuous max. speed (1 Intermittent max. speed (1 Max. flow absorbed Torque Torque at 350 bar (5100 psi Theoretical

More information