OUNCES PRESSURE REGULATOR
|
|
|
- Suzan Summers
- 5 years ago
- Views:
Transcription
1 OUNCES PRESSURE REGULATOR BACK PRESSURE TO VACUUM APPLICATIONS: To maintain ounces of positive pressure on systems flowing into a downstream vacuum, such as vapor recovery systems. PRESSURE RANGE: Upstream: 0.5 ounces to 2.5 psig Downstream: 6 Hg. Vacuum, minimum OPERATION: Assume the PILOT SPRING is compressed with the ADJUSTING SCREW for a set pressure greater than the Upstream Pressure (Red). The Pilot Assembly is forced downward by the PILOT SPRING. The lower seat for the PILOT PLUG (Yellow to Blue) is closed and the upper seat for the PILOT PLUG (Red to Yellow) is open. This lets full Upstream Pressure (Red) load the MOTOR VALVE DIAPHRAGM to close the valve. Additional closing effort is provided by Downstream Vacuum (Blue) under the MOTOR VALVE DIAPHRAGM. As the Upstream Pressure (Red) increases to the set pressure, the Pilot Assembly moves upward against the PILOT SPRING to first close the upper seat (Red to Yellow) and open the lower seat (Yellow to Blue). Motor Valve Diaphragm Pressure (Yellow) is vented to the Downstream Vacuum (Blue). As the Motor Valve Diaphragm Pressure (Yellow) is decreased the Upstream Pressure (Red) acting under the motor valve seat and the Downstream Vacuum (Blue) acting on top of the motor valve seat, opens the valve. With relief of the Upstream Pressure (Red) through the valve, the Pilot Assembly assumes a position in which both seats of the PILOT PLUG are closed. Motor Valve Diaphragm Pressure (Yellow) is regulated by the intermittent vent pilot three-way valve action of the PILOT PLUG to reposition the Motor Valve Stem Assembly for changes in flow rate. The rapid but stable repositioning produces a true throttling action. Kimray is an ISO certified manufacturer. Change Diaphragm numbers Bulletin No. A07043 Issued 12/17
2 OUNCES PRESSURE REGULATOR BACK PRESSURE TO VACUUM * Gasket 242, 4 Req'd. Adjusting Screw 897 Nut SS6 (2.5 lbs. Std.) Spring Plate 636SS6 (5 lbs. Opt.) Bonnet 1336D 7148S6 (20 lbs. Opt.) Nut (2.5 lbs. Std.) Spring 3061 (5 lbs. Opt.) 4379 (20 lbs. Opt.) Stem 1339 * O Ring 265 Diaphragm 1212 * Spring 1360 Gasket 1216 * Screw 1449, 6 Req'd. Pilot Plug 112 Lower Diaph. Plate 1340 Spring 566 Housing 1206D Diaphragm Plate 1208 Breather Plug 147 * Diaphragm 110 Nut 241, 10 Req'd. Screw 191, 4 Req'd. Plug 699 Plug 699 Seat 565 * Gasket 196 to 199 Housing 4211 to 4214 * Gasket * Diaphragm Seat Disc 2493, 2" 2494, 3" 2495, 4" 2961, 6" Plug , 2" 277, 3" 196, 4" 279, 6" Seat , 2" 1640, 3" 2015, 4" 2140, 6" Nut 241, 4 Req'd. * Gasket 118 Base 4995 Nipple 2516 Ell 875, 2", 3", & 6" Conn. 874, 4" 965, 8 Req'd. 2" 907, 10 Req'd. 3" Screw907, 12 Req'd. 4" 2142, 16 Req'd. 6" Screw 236, 10 Req'd. 648, 2", 3", & 6" Nipple 76, 4" Lower Housing 1356D 4050SS6, 2" 2505SS6, 3" Tubing 2505SS6, 4" 4312SS6, 6" Ell 875 Plate Ell 877 Stem 138 to 141 Removable Seat Gauge 4080 Filter 1/4" F , 2" 2491, 3" 2492, 4" 2958, 6" Ell , 2" 4128, 3" Tubing 4129, 4" 4136, 6" 2487, 2" 2488, 3" Bonnet 2489, 4" 2956, 6" 2496SS6, 2" 2497SS6, 3" 2498SS6, 4" 3075SS6, 6" * Seat 164HSN to 167HSN * Nut THRU VALVES AVAILABLE: 173, 2" 906, 3" & 4" 175, 6" Body 2468, 2" 2469, 3" 2470, 4" 2959, 6" NOTES: Ratio Plug 177SS6, 2" 178, 3" 179, 4" 3079SS6, CAT. SIZE OPER. MAX NO. TYPE REG. NO PRES. W.P. KIT AHA2.5 2 FLGD. 2.2 FGT OBPV-S AHA5 2 FLGD. 2.5 FGT OBPV-S AHA20 2 FLGD. 202 FGT OBPV-S AHB2.5 3 FLGD. 3.2 FGT OBPV-S AHB5 3 FLGD. 3.5 FGT OBPV-S AHB20 3 FLGD. 302 FGT OBPV-S AHC2.5 4 FLGD. 4.2 FGT OBPV-S AHC5 4 FLGD. 4.5 FGT OBPV-S AHC20 4 FLGD. 402 FGT OBPV-S AHD2.5 6 FLGD. 6.2 FGT OBPV-S AHD5 6 FLGD. 6.5 FGT OBPV-S AHD20 6 FLGD. 602 FGT OBPV-S Bulletin No. A07043 Issued 12/17 *These parts are recommended spare parts and are stocked as repair kits. The number of a series assigned to a part indicated different line sizes. For example: Diaphragm 164H-2, 165H-3, 166H-4 and 167H-6. Kimray is an ISO certified manufacturer. Change Diaphragm numbers
3 FLOW COEFFICIENT Table 1 - Flow Coefficient(Cv) at % stem travel for Pilot Operated Regulators 1" Pressure Regulator in.(mm) 1/2 in (12mm) Reduced in (25mm) Full Port " Pressure Regulator 1 1/4 in (31 mm) Reduced in Removable Full Port * in (50 mm) Full Port * " Pressure Regulator 1 5/8 in (66 mm) Reduced in (76 mm) Full Port " Pressure Regulator 2 in (50 mm) Reduced in (100 mm) Full Port " Pressure Regulator 3 in (76 mm) Reduced in (152 mm) Full Port Kimray flow equations conform to ANSI/ISA Kimray inherent flow characteristics conform to ANSI/ISA * Use "2 inch Removable Full Port" values for regulators with operating pressure ranges of psig, psig & psig A:I
4 DIMENSIONS FOR: BACK PRESSURE UPSTREAM DIFFERENTIAL PRESSURE PRESSURE REDUCING-BALANCED PRESSURE REDUCING VACUUM PRESSURE DIFFERENTIAL PRESSURE REDUCING BACK PRESSURE VACUUM LIQUID BACK PRESSURE G DUCTILE 250 S/FGT-BP-S FOR: LOW PRESSURE BACK PRESSURE OUNCES BACK PRESSURE TO VACUUM OUNCES PRESSURE REDUCING OUNCES PRESSURE REDUCING VACUUM VACUUM BACK PRESSURE TO VACUUM DUCTILE LINE SIZE BODY SIZE A B C D * E F G H * I 1" NPT 4 3/8" 1 1/8" 7 1/2" 11 5/8" 3 1/4" 2" 250 S/FGT 3" 4" NPT 8 1/2" 2 1/8" 11 1/2" 10 1/2" 6 1/2" FLANGED 9" 3" 11 1/2" 10 1/2" 6 1/2" 9 1/8" 14 1/2" 14" GROOVED 8 3/4" 2 1/8" 11 1/2" 10 1/2" 6 1/2" NPT 10 1/2" FLANGED 10 3/8" NPT 12 1/16" 3 1/16" 13" 12" 8 1/2" FLANGED 12 3/16" 3 3/4" 13" 12" 8 1/2" 12 3/8" 16 1/2" 15 1/2" NPT 15" 1/16 4" 14 1/2" 13 3/16" 10 1/2" FLANGED 15 1/16" 4 1/2" 14 1/2" 13 3/16" 10 1/2" 15 1/16" 18 1/2" 16 11/16" 6" FLANGED 22" 5 1/2" 17" 17 7/8" 16" 21 15/16" 20 1/2" 18 3/8" FLANGE DIMENSIONS ARE ANSI 125/150 STANDARD. *Add 7/8" to Pressure Reducing Balanced and Up Stream Differential Pressure Regulators for this dimension. A:II Configuration of Back Pressure Valve is a trademark of Kimray, Inc.
5 SEALS Table 2 - Seal Options Part Standard Material Optional Material Pilot Diaphragm Seat Nitrile FKM, HSN, AFLAS, Gylon O-rings Nitrile FKM, HSN, AFLAS, Gylon All Diaphragms Except Pilot Diaphragm Nitrile FKM, HSN, AFLAS, Gylon Diaphragm Pilot Diaphragm Polyurethane FKM, HSN, AFLAS, Gylon Diaphragm O Ring Seat Resistance Properties Table 3 - Seal Specifications NITRILE HIGHLY POLY- SATURATED FKM AFLAS URETHANE NITRILE GYLON Kimray Suffix - HSN V AF P GY Abrasion G G G GE E E Acid F E E E P E Chemical FG FG E E FG E Cold G G PF P G E Flame P P E E P P Heat G E E E F E Oil E E E E G E Ozone P G E E E E Set GE GE E PF F P Tear FG FG F PF GE E Water/Steam FG E P GE P E Weather F G E E E E CO2 FG GE PG GE G E H2S P FG P E G E Methanol G E PF PF P E Dynamic GE GE GE GE E P Electrical F F F E FG E Impermeability G G G G G E Tensile Strength GE E GE FG E E Temp. Range ( F) -40 to +220 F -15 to +300 F -10 to +350 F +25 to +450 F -40 to +220 F -350 to +500 F Temp. Range ( C) -40 to +105 C -26 to +149 C -23 to +177 C 0 to +232 C -40 to +104 C -212 to +260 C Form O,S,D O,S,D O,S,D O,S,D S,D S,D RATINGS: P-POOR, F-FAIR, G-GOOD, E-EXCELLENT Configuration of Back Pressure Valve is a trademark of Kimray, Inc. A:III
6 MATERIAL SPECIFICATION Table 5 - Materials of Construction Part Description Valve Size Standard Material Optional Material(s) Ratio Plug Seat Disc 1" & 2" 316 Powdered Metal SS-316NI-25 N/A 1" & 2" Reduced Trim Steel, ASTM A Stainless Steel ASTM A-479 3" Powdered Metal F Stainless Steel ASTM A-479 4" & 6" Ductile, ASTM A Stainless Steel ASTM A-479 1" Powdered Metal F Stainless Steel ASTM A-479 2", 3" & 4" Ductile, ASTM A-395 Stainless Steel ASTM A-351 CF8M 6" Ductile, ASTM A-395 Stainless Steel ASTM A-240 Stem 1" thru 6" 303 Stainless Steel, ASTM A Stainless Steel ASTM A-479 Body 1" thru 6" Ductile, ASTM A-395 N/A Body 2" thru 6" Steel, ASTM A-216 WCB Stainless Steel ASTM A-351 CF8M Tubing Removable Seat 175 W.P. or Less Copper Tubing ASTM B-380 UNS C Stainless Steel ASTM A-213 Copper Tubing ASTM B-280 UNS C Stainless Steel ASTM A-213 Greater Than 175 W.P. 304 Stainless Steel ASTM A Stainless Steel ASTM A-213 2" thru 6" Ductile Body Ductile, ASTM A-395 Stainless Steel ASTM A-351 CF8M 2" thru 6" Steel Body Stainless Steel ASTM A-351 CF8M N/A Stem Tubing Seat Disc Ratio Plug Body Table 4 - Material Specification Body Inner Parts CAST CAST DUCTILE 303 STAINLESS 316 STAINLESS 17-4 PH STAIN- LESS KIMRAY SUFFIX CS CD SS6 SS6 PH ASTM GROUP ASTM A-216 ASTM A-395 ASTM A-582 ASTM A-479 ASTM A-564 GRADE WCB UNS J03002 F32800 S30300 S31600 S17400 NACE Compliant Yes Yes No Yes Yes A:IV Configuration of Back Pressure Valve is a trademark of Kimray, Inc.
7 TEMPERATURE Table 6 - Temperature vs. Pressure Rating Flange Class ASTM Class 150 RF Temperature F ( C) Static Test Pressure (psig) 450 (31 bar) Maximum Allowable Non-Shock Pressure (psig) CAST DUCTILE ASTM A-395 Flange Class 150 RF -20 to 100 (-28 to 37) 250 (17.2 bar) 200 (93) 235 (16.2 bar) 300 (148) 215 (14.8 bar) 400 (204) 200 (13.7 bar) 500 (260) 170 (11.7 bar) 600 (315) 140 (9.6 bar) 650 (343) 125 (8.6 bar) 700 (371) CAST ASTM A WCB Flange Class 150 RF -20 to 100 (-28 to 37) 285 (20.0 bar) 200 (93) 260 (17.9 bar) 300 (148) 230 (15.9 bar) 400 (204) 200 (13.8 bar) 500 (260) 170 (11.7 bar) 600 (315) 140 (9.7 bar) 650 (343) 125 (8.6 bar) 700 (371) 110 (7.6 bar) FLANGED (150RF) SCREWED (NPT) GROOVED Kimray valves conform to ASME B for working pressure vs working temperature & ASME B for flanges and flanged fittings. Configuration of Back Pressure Valve is a trademark of Kimray, Inc. A:V
PRESSURE REGULATORS PRESSURE REDUCING. APPLICATION: Regulation of inlet pressure to gas compressors. Control of supply or distribution system pressure
PRESSURE REDUCING APPLICATION: Regulation of inlet pressure to gas compressors. Control of supply or distribution system pressure PRESSURE RANGE: Upstream: 10 psig to 300 psig Downstream: 10 psig to 300
PRESSURE REGULATORS LIQUID BACK PRESSURE
LIQUID BACK PRESSURE APPLICATION: Control back pressure in liquid packed systems where an auxiliary source of supply gas pressure is available. SUPPLY PRESSURE: Equal to or not less than 60% of controlled
PRESSURE REGULATORS LIQUID BACK PRESSURE
LIQUID BACK PRESSURE APPLICATION: Control back pressure in liquid packed systems where an auxiliary source of supply gas pressure is available. SUPPLY PRESSURE: Equal to or not less than 60% of controlled
PRESSURE REGULATORS GAS BACK PRESSURE. APPLICATION: Vent lines on oil separators, flow treaters, compressor stations, gas gathering systems.
GAS BACK PRESSURE APPLICATION: Vent lines on oil separators, flow treaters, compressor stations, gas gathering systems. CERTIFICATIONS: Canadian Registration Number (CRN): 0C16234.24567890NTY (Ductile)
OUNCES PRESSURE REGULATOR
OUNCES PRESSURE REGULATOR VACUUM BACK PRESSURE TO VACUUM APPLICATIONS: Vacuum distribution systems, compressor suction regulation to prevent excessive vacuum on wells. A minimum of 10 psi instrument gas
OIL & WATER VALVES DIAPHRAGM MOTOR VALVE DUCTILE IRON VALVES AVAILABLE: ITEM QTY. DESCRIPTION PART NO.
DIAPHRAGM MOTOR VALVE DUCTILE IRON * 1 2 4 3 5 6 * 15 * 15 14 * 30 29 28 31 16 1 18 13 1 * 19 20 21 8 9 * 10 * 11 12 * ITEM QTY. DESCRIPTION PART NO. 1 2 Gasket * 364 2 1 Stuffing Box Nut 345 3 1 Follower
MECHANICAL LEVEL CONTROLS
PISTON BALANCED LEVER OPERATED APPLICATIONS: As oil or water dump valves on separators, treaters, knockouts, and other similar accumulators where higher pressures may occur FEATURES: Balanced, single soft
LEVER OPERATED LIQUID LEVEL CONTROLS
PISTON BALANCED THROTTLING LEVER OPERATED APPLICATIONS: As oil or water dump valves on separators, treaters, knockouts, and other similar liquid accumulators. Designed for high pressure erosive service.
OIL & WATER VALVES TREATER VALVE
TREATER VALVE APPLICATIONS: As oil or water valve for emulsion treaters, water knockouts and gunbarrels. Can be used for pressure, atmospheric, or vacuum operation. Ideal for discharging salt water to
LOW PRESSURE MOTOR VALVES
LOW MOTOR S MT BP SPRING LOADED BACK PRESS. w/reduced INNER APPLICATIONS: Liquid or gas systems where a 0 to psig adjustable back pressure is desired, such as treaters, free water knockouts, pressure vessels,
PRESSURE REGULATORS PILOT OPERATED. Configuration of Back Pressure Valve is a trademark of Kimray, Inc.
PRESSURE REGULATORS PILOT OPERATED Configuration of Back Pressure Valve is a trademark of Kimray, Inc. NOTE: We reserve the right to modify or change, without prior notice, any statement or information
BALANCED MOTOR VALVES
PISTON BALANCED PRESSURE CLOSE APPLICATIONS: Pilot operated oil or water valve for separators, meters, and water knockouts where a reduced signal pressure is available, and where freezing occurs due to
HIGH PRESSURE CONTROL VALVES
1 & 2 HPCV APPLICATIONS: For discharge of liquid or gas from vessels, separators, treaters, knockouts and other similar liquid accumulators. For back pressure or pressure reducing applications with pressure
HIGH PRESSURE CONTROL VALVES
1 & 2 HPCV APPLICATIONS: For discharge of liquid or gas from vessels, separators, treaters, knockouts and other similar liquid accumulators. For back pressure or pressure reducing applications with pressure
HIGH PRESSURE CONTROL VALVES
1 & 2 HPCV APPLICATIONS: For discharge of liquid or gas from vessels, separators, treaters, knockouts and other similar liquid accumulators. For back pressure or pressure reducing applications with pressure
SPRING LOADED VENTS. Set Points of 3 PSIG and Above PROTECTOSEAL
SPRING LOADED VENTS Set Points of 3 PSIG and Above PROTECTOSEAL SERIES STYLE 9540 End-of-Line Pressure/Vacuum Breather Vent 19540 Pipe-Away Pressure/Vacuum Breather Vent 9240 End-of-Line Vacuum Relief
P99 Pressure Reducing Regulator
P99 Pressure Reducing Regulator Applications City / District gate operation Commercial buildings Boilers, furnace, oven Plant air service Features 5 Pilot choices for low to extra high pressure Up to 1,000
550 Series Back Pressure, Low Pressure Valve
Application: The are used on any installation where the pressure upstream must be kept in a preset range. These valves can be used as a pressure relief valve, custody transfer dump valve to hold a certain
Ball Valves. Seal Welded Style BVS2...2 Carbon Steel Technical Data 2200 PSI ¼ Stainless Steel Technical Data 2160 PSI ¼
Ball Valves Seal Welded Style BVS2...2 Carbon Steel Technical Data 2200 PSI ¼ - 4...3 316 Stainless Steel Technical Data 2160 PSI ¼ - 4...3 Style BVSC...4 Carbon Steel Technical Data 2200 PSI ¼ - 2...5
P630 High Flow Gas Regulator
High Flow Gas Regulator Stainless Steel Internals are Standard Steel Units comply with NACE MR0175 Durable Powder Coated Exterior Wide of Flow Capacities The is a spring loaded, direct-operated regulator
Series 2200 and 2220 Control Valves
Series 2200 and 2220 Control Valves Space-Saving Solution: Yokeless design fits tight separator and scrubber applications Series 2200 Series 2220 Norriseal Series 2200 and 2220 control valves have been
P627 High Flow Gas Regulator
P627 High Flow Gas Regulator Wide of Flow Capacities Durable Powder Coated Exterior Installation Versatility NACE Construction Available The P627 is a spring loaded, direct-operated regulator for both
310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve
310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve Features and Benefits Uninterrupted gasket surfaces help eliminate problems associated with seat retaining screws
Keystone Figures 310/312 K-LOK Butterfly Valves
310 - Wafer high performance butterfly valve 312 - Lugged high performance butterfly valve Features General Application High performance applications such as steam, chill water, water, utility lines, gasoline,
High Capacity Direct Operated Pressure Reducing Valve. Features
MK608UBAN Series High Capacity Direct Operated Pressure Reducing Valve The MK608UBAN series are spring loaded, direct-operated, pressure reducing regulators. Their main function is to regulate the outlet
Types 1808 and 1808A Pilot-Operated Relief Valves or Backpressure Regulators
Bulletin 71.4 D0163X012 Type 1808 February 17 Types 1808 and 1808A Pilot-Operated Relief Valves or Backpressure Regulators Type 1808 Type 1808A Figure 1. Types 1808 and 1808A Pilot-Operated Relief Valves
KEYSTONE FIGURES 310/312 K-LOK BUTTERFLY VALVES
310 - Wafer high performance butterfly valve 312 - Lugged high performance butterfly valve FEATURES GENERAL APPLICATION High performance applications such as steam, chill water, water, utility lines, gasoline,
HIGH PRESSURE CONTROL VALVES
HIGH PRESSURE CONTROL VALVES SECTIONE1 Configuration of High Pressure Control Valve is a trademark of Kimray, Inc. NOTE: We reserve the right to modify or change, without prior notice, any statement or
PRESSURE REGULATOR BACK PRESSURE TO ATMOSPHERE WITH OUTSIDE SUPPLY
PRESSURE REGULATOR BACK PRESSURE TO ATMOSPHERE WITH OUTSIDE SUPPLY All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been
310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve
310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve Features and Benefits Uninterrupted gasket surfaces help eliminate problems associated with seat retaining screws
P627 High Flow Gas Regulator
P627 High Flow Gas Regulator Wide of Flow Capacities Durable Powder Coated Exterior Installation Versatility NACE Construction Available The P627 is a spring loaded, direct-operated regulator for both
Design D4 Control Valve
Product Bulletin Design D4 Control Valve D4 Valve The Design D4 control valve is a compact, rugged globe valve designed primarily for high-pressure throttling applications. This valve is ideal for use
Model TB TECHNICAL BULLETIN. Pressure / Vacuum Vent with Pipe-Away
TECHNICAL BULLETIN 3200 - TB 04-16 Pallet Diaphragm Material: FEP TFE - Standard. Also available in FKM, EPDM and Buna-N. ISO Registered Company Model 3200 Pressure / Vacuum Vent with Pipe-Away OBJECTIVE
Fisher D4 Control Valve Assembly
Product Bulletin D103039X012 Fisher D4 Control Valve Assembly D4 Valve The Fisher D4 control valve is a compact, rugged globe valve designed primarily for high-pressure throttling applications. This valve
MK508MM Series. Back Pressure Regulators Mark 508MM Self-Operated Back Pressure Regulators. Self-Operated Back Pressure Regulators.
MK508MM Series Self-Operated Back Pressure Regulators The MK508MM series are spring loaded, self actuated, direct-operated valves. The Mark 508MM Back Pressure Regulating Valves regulate upstream pressure
P200 Pressure Regulator
P200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P202 has internal relief valve for overpressure protection The P200 series pressure regulator is a manual, direct acting,
FLOAT OPERATED LEVEL CONTROLLER
GEN II ELECTRONIC BACK MOUNT APPLICATIONS: Liquid level controller f oil and gas separats, water knockouts, gas scrubbers and accumulats. Liquid interface control in fluids of 0.20 minimum differential
Repair Manual MECHANICAL OIL VALVE
MECHANICAL OIL VALVE Repair Manual This Manual for Mechanical Oil Valves purchased before December 2017 INDEX Introduction... 1 Elastomer Materials... 2 Repair Kit Contents... 3 Disassembly... 4 Appendix
Type 310A-32A Pressure Reducing Regulator
Bulletin 71.2 D102066X012 Type 310A February 2017 Type 310A-32A Pressure Reducing Regulator Figure 1. Type 310A Regulator with Type 32A Pilot Introduction The Type 310A pilot-operated high-pressure regulator
P200 Pressure Regulator
P200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P202 has internal relief valve for overpressure protection The P200 series pressure regulator is a manual, direct acting,
Type MR108 Direct-Operated Backpressure Regulators
August 2013 Type MR108 Direct-Operated Backpressure Regulators P1202 P1203 TYPE MR108 WITH LOW- ACTUATOR TYPE MR108 WITH HIGH- ACTUATOR Figure 1. Type MR108 Direct-Operated Backpressure Regulators Contents
Types 1808 and 1808A Pilot-Operated Relief Valves or Backpressure Regulators
Instruction Manual Form 5116 Types 1808 and 1808A July 2010 Types 1808 and 1808A Pilot-Operated Relief Valves or Backpressure Regulators! Warning Failure to follow these instructions or to properly install
BERMAD Fire Protection
Differential-Pressure Sustaining Valve Description The Model FP-436 Differential-Pressure Sustaining Valve is a hydraulically-operated, diaphragm-actuated, control valve that sustains minimum pre-set,
Type MR108 Direct-Operated Backpressure Regulators
July 2016 Type MR108 Direct-Operated Backpressure Regulators P1202_1 P1203_1 Type mr108 with low-pressure Actuator Type mr108 with high-pressure actuator Figure 1. Type MR108 Direct-Operated Backpressure
627 Series Pressure Reducing Regulators
627 Series Pressure Reducing Regulators Introduction The 627 Series direct-operated reducing regulators (Figure 1) are for low and high systems. These regulators can be used with natural gas, air, or a
88A-100 Series. Carbon Steel ANSI Class 150 Flanged Std. Port Ball Valve - 1-1/2 through 2 STANDARDS COMPLIANCE STANDARD FEATURES
Carbon Steel ANSI Class 150 Flanged Std. Port Ball Valve - 1-1/2 through 2 2. Retainer ASTM A108 Type 1215 3. Ball ASTM A108 Type 1215 Chrome Plated 9. Gland Plate 302 or 304 SS 10. Stem Nut 316 SS 11.
P95H Regulator Applications P95H Part Matrix Specifi cations Materials of Construction P95H Flow Coeffi cients Wide Open Coeffi cients
PH Regulator Large Capacity Working Media Include ir, Steam and Liquids ll Vents are Tapped The PH is a direct operating pressure reducing regulator with large capacity. Ideally suited for uses in oil
R627 High Flow Gas Regulator with Internal Relief
High Flow Gas Regulator with Internal Relief The Relieving Regulator has an internal relief valve that provides protection against over pressurization. As output pressure builds up above the start-to-discharge
Masoneilan * Pressure Regulators Steam, Gas or Liquid Service Models 525 and 526
GE Oil & Gas Technical Specifications 05/2013 Masoneilan * Pressure Regulators Steam, Gas or Liquid Service Models 525 and 526 Pressure Reducing, Back Pressure and Differential Pressure Control 2 GE Oil
* Contact your sales representative for compliance to NACE MR or later requirements.
VALVES & CONTROLS crosby SERIES 00, 00 OMNI-TRIM, AND BP OMNI-TRIM Crosby s Series 00 adjustable blowdown, Series 00 fixed blowdown OMNI-TRIM, and BP OMNI-TRIM full nozzle pressure relief valves have a
Carbon Steel ANSI Class 150 Flanged Full Port Ball Valve -
Description (1/2 & 3/4 Valves) Material 2. Retainer ASTM A108 Type 1215 3. Ball ASTM A108 Type 1215 8. Stem Nut 300 Series Stainless Steel 9. Lever 300 Series Stainless Steel w/vinyl Grip 10. Stem Bearing
General Specifications
General Specifications GS 22B01C06-01EN-A C13ST Manifolds for Traditional Mount Differential Pressure Transmitters Designed and manufactured by AS-Schneider, Yokogawa C13ST-3 and C13ST-5 manifolds are
LOW PRESSURE BALANCED VALVE DIAPHRAGM BALANCED
DIAPHRAGM BALANCED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to
F300 Pressure Regulator
F300 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P302 has Internal Relief Valve for Overpressure Protection Ideal for Fix Factor Billing The F300 series pilot operated
P627 High Flow Gas Regulator
P627 High Flow Gas Regulator Wide of Flow Capacities Durable Powder Coated Exterior Installation Versatility NACE Construction Available The P627 is a spring loaded, direct-operated regulator for both
Applications. T98H Part Matrix. Specifications. Spring Range. Materials of Construction. T98H Regulator Rebuild Kits. marshbellofram.
TH Back Regulator / Valve The TH monitors upstream pressure and opens to relieve excess pressure increases above setpoint. s a Back Regulator, the upstream pressure is monitored and released downstream
TRUNNION BALL VALVES. TBV 7.10
TRUNNION BALL VALVES WWW.VALVE.COM TBV 7.10 ABOUT US Our mission at Universal Flow (), is to provide a quality product at a competitive price and to meet the needs and requirements of our customers in
T205VB Series Tank Blanketing Vacuum Breakers
February 2014 T205VB Series Tank Blanketing Vacuum Breakers Figure 1. Typical T205VB Series Vacuum Breaker Introduction The T205VB Series vacuum breakers (Figure 1) are used for precise control of small
Direct-operated, Back Pressure Regulating Valve. Features
MK508BPM Series Direct-operated, Back Pressure Regulating Valve The MK508BPM series are spring loaded, self actuated, direct-operated, valves. Pressure relief valves are used to protect the system from
D I V I S I O N O F M A R S H B E L L O F R A M
PH Regulator Large Capacity Working Media Include ir, Steam and Liquids ll Vents are Tapped The PH is a direct operating pressure reducing regulator with large capacity. Ideally suited for uses in oil
SECTION Pressure & Temperature Control
16 Pressure & Temperature Control ARMSTRONG PRODUCT CATALOGUE 70 Pressure Reducing s Pressure Reducing s Armstrong pressure reducing valves (PRVs) and temperature regulators help you manage steam, air
Type 441 CATALOG. Flanged Safety Relief Valves. The-Safety-Valve.com
Type 441 Flanged Safety Relief Valves CATALOG The-Safety-Valve.com General Information LESER India Safety Relief Valves The safety valve Type 441 represents High capacity related to the safety valve size
P200 Pressure Regulator
P200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P202 has internal relief valve for overpressure protection The P200 series pressure regulator is a manual, direct acting,
PRESSURE REDUCING CONTROL VALVE
PRESSURE REDUCING CONTROL VALVE 06/08 Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Reducing setpoint is adjustable 2 (AOS) X P/L Standard Components 1 Main
R627 High Flow Gas Regulator with Internal Relief
High Flow Gas Regulator with Internal Relief The Relieving Regulator has an internal relief valve that provides protection against over pressurization. As output pressure builds up above the start-to-discharge
MODEL 106/206-PG POWER OPERATED GLOBE VALVE Sizes 1/2" to 8" (106-PG) 3" to 10" (206-PG) Installation, Operating and Maintenance Instructions
MODEL 106/206-PG POWER OPERATED GLOBE VALVE Sizes 1/2" to 8" (106-PG) 3" to 10" (206-PG) Installation, Operating and Maintenance Instructions DESCRIPTION: This valve is the basic component used for most
* Contact your sales representative for compliance to NACE MR or later requirements.
VALVES & CONTROLS crosby SERIES 800, 900 OMNI-TRIM, AND BP OMNI-TRIM Crosby s Series 800 adjustable blowdown, Series 900 fixed blowdown OMNI-TRIM, and BP OMNI-TRIM full nozzle pressure relief valves have
MODEL 5540 CONTENTS. Installation, Operation and Maintenance Instructions 1.0 GENERAL
Installation, Operation and Maintenance Instructions MODEL 5540 Sep 20 CONTENTS.0 GENERAL. Model Number---------------------------------------------------------------------------------------------------------------
627 Series Pressure Reducing Regulators
627 Series Pressure Reducing Regulators Introduction The 627 Series direct-operated pressure reducing regulators (Figure 1) are for low and high pressure systems. These regulators can be used with natural
Condensed Valve Guide Gate Globe Check Ball Strainer. Warren Valve - Quality Since 1963
800.231.6969 Condensed Valve Guide Gate Globe Check Ball Strainer Warren Valve - Quality Since 1963 Gate, Globe & Check Valves #1156 #2156 #3156 Gate Globe Check Pressures Class Figure 150 - #1156 300
Control Valve. 3-Piece 30, 60, or 1/8" Slotted Port. General Chemical. Industrial. Power INLINE BALLVALVE.COM
324 Control 3-Piece 30, 60, or 1/8" Slotted General Chemical Industrial Power INLINE BALLVALVE.COM The 324 Series Control The 324 series control valve incorporates several innovative design features for
PRESSURES TO 740 PSIG (51 BARG) TEMPERATURES TO 800 F (427 C) MODELS. 300Y Series Ordering Code. Add l Inlet Size Model Body Dash Perf Mesh Require-
APPLICATIONS Steam, liquid, gas and oil service Power industry Pulp and paper Chemical industry Process Equipment Metal & Mining Water & Waste OPTIONS Other perforated screens and mesh liners Other drain
High Performance Butterfly Valves
Tech Bulletin Page 500-11 MAX SEAL HP SERIES High Performance Butterfly Valves Available with Soft and Metal Seating MODEL BL630 Size Range 2 thru 24, optional thru 120 ANSI Class 150//600/900 20 Lug 6
Mustang Series PRESSURE REDUCING CONTROL VALVE. M115 (Globe) M1115 (Angle) Schematic. Standard Components. Options & Accessories.
PRESSURE REDUCING CONTROL VALVE 02/09 Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Reducing setpoint is adjustable 2 (AOS) P/L Standard Components 1 Main Valve
Jordan Control Valve Series
Jordan Control Valve Series Control Valves A control valve is used to manipulate flowing fluids like, gas, water, steam or process solutions. It compensates for changes in flow or pressure and regulates
MK508UBS Series. Back Pressure Regulator MK508UBS. Threaded or Flanged Connections Carbon Steel, Stainless Steel & Alloy Construction.
MK508UBS Series Threaded or Flanged Connections Carbon Steel, Stainless Steel & Alloy Construction The MK508UBS Series are spring loaded, direct-operated, pressure relief valves used downstream of pressure
See Water Pressure Reducing Valves Catalog (PHBRWPRV) for more detailed information about the products in this section.
See Catalog (PHBRWPRV) for more detailed information about the products in this section. Water pressure reducing valves PR (36LF) Series Residential and commercial applications The Apollo 36LF pressure
Model DF100 Control Valve
FEATURES NACE Service Ready Standard construction for the DF100 control valve features NACE trim. The valve bonnet and body also conform to NACE MR0175 (National Association of Corrosion Engineers) recommendations.
HD Series. Pilot-Operated Regulating Valves. HD Series features & benefits
Watson McDaniel reserves the right to change the designs and/or materials of its products out notice. 2004 Watson McDaniel Company features & benefits Ductile Iron body for higher pressures Full port strainer
Type EZR Relief Valve or Backpressure Regulator
Instruction Manual Form 5476 Type EZR Relief 03/01 Type EZR Relief Valve or Backpressure Regular W7347 Introduction Figure 1. Type EZR Relief Valve or Backpressure Regular Scope of Manual This instruction
See Water Pressure Reducing Valves Catalog (PHBRWPRV) for more detailed information about the products in this section.
See Catalog (PHBRWPRV) for more detailed information about the products in this section. WATER PRESSURE REDUCING VALVES PR (36LF) SERIES RESIDENTIAL AND COMMERCIAL APPLICATIONS The Apollo 36LF pressure
Series FS50 Fire Safe API 607 4th Edition Full Port Flanged Ball Valves
USA 800-766-0076 Fax 33-890-4456 www.smithcooper.com www.sharpevalves.com Los Angeles, CA Chicago, IL Atlanta, GA Vancouver, WA Houston, TX Design Features Fire Safe API 607 4TH Edition flanged valves
Type EZR Relief Valve or Backpressure Regulator
Instruction Manual Form 5476 Type EZR Relief May 2012 Type EZR Relief Valve or Backpressure Regulator Introduction Scope of the Manual W7347 This instruction manual provides installation, startup, shutdown,
BIRKETT SAFESET SERIES PILOT OPERATED SAFETY RELIEF VALVES
Pop action and modulating pilot operated safety valves with a unique full nozzle design and dimensions to API 526 FEATURES GENERAL APPLICATION Safeset valves are self-contained pilot operated safety relief
PRESSURE REDUCING VALVE
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING VALVE with LOW-FLOW BY-PASS FEATURE Main Line valve
Crosby Series 800 and 900 OMNI-TRIM Pressure Relief Valves. Flow Control
Crosby s Series 800 adjustable blowdown and Series 900 fixed blowdown OMNI-TRIM full nozzle pressure relief valves have a simplified, single trim design with superior application versatility. Features
PRESSURE REDUCING VALVE
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Closes quickly when downstream pressure exceeds reduced pressure setpoint 3 PRESSURE REDUCING VALVE with SURGE
MODEL 345 HIGH PRESSURE REDUCING REGULATOR TECHNICAL BULLETIN 345-TB FEATURES High inlet and outlet pressures; high pressure drops.
TECHNICAL BULLETIN 02-16 ISO Registered Company MODEL 345 HIGH PRESSURE REDUCING REGULATOR The Model 345 is a piston style, heavy duty, high pres sure reducing regulator that can include bal anced trim
High CATALOG. Efficiency. Pilot Operated Safety Valves Series 810 Pop Action Series 820 Modulate Action. The-Safety-Valve.com
High Efficiency Pilot Operated Safety Valves Series 10 Pop Action Series 20 Modulate Action CATALOG The-Safety-Valve.com Valve finder How to find the right product group High operating to set pressure
T205 Series Tank Blanketing Regulators
T205 Series Tank Blanketing Regulators Bulletin 74.1:T205 September 2013 Figure 1. Type T205 Tank Blanketing Regulator Contents Features...1 Introduction...2 Specifi cations...2 Principle of Operation...2
T200 Pressure Regulator
T200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges T202 has internal relief valve for overpressure protection The T200 series pressure regulator is a manual, direct acting,
P600 Pressure Regulator
P600 Pressure Regulator The BelGAS P600 series is a direct operated, pressure reducing regulator that can be used as a pressure loaded regulator, switching valve, or monitoring regulator. Available with
MERCER VALVE SERIES Flanged THINK...MERCER FIRST MERCER VALVE CO., INC. AUTO SEAT TECHNOLOGY
9100 SERIES Flanged THINK...MERCER FIRST MERCER VALVE MERCER VALVE CO., INC. AUTO SEAT TECHNOLOGY 9100 Series Product Overview The Mercer Valve 9100 Series Pressure Relief Valve is State of the Art in
High pressure valves. Inspired By Challenge
Inspired By Challenge Floating Valves High pressure General Series 7 Series 8 Series Introduction Ordering code system The Habonim high pressure valve series is based on a floating ball valve technology,
KF Valves Check Valves
Check Valves Excellence In Flow Control High Performance By Design Applicable Standards KF check valves conform to ANSI, API and NACE specifications to meet your application requirements. ANSI- American
General Specifications
General Specifications GS 22B01C05-00EN-A C13ST Manifolds for Traditional Mount Gauge and Absolute Pressure Transmitters Designed and manufactured by AS-Schneider, Yokogawa C13ST-2 2-Valve manifolds are
Built-in Slam-Shut Valve. Independent pneumatic control Accuracy class: ±5% Response time: 1 second. 1/2, 11/16, and 3/4-inch (13, 18, and 19 mm)
RP Series Regulators Introduction The RP Series regulators are direct-operated with non-balanced trim. Normally they are fitted with a built-in filter. They are produced in the following versions: Types
GE Oil & Gas. Technical Specifications 07/ Series. Masoneilan * High Performance Butterfly Valves (HPBV)
GE Oil & Gas Technical Specifications 07/2014 39003 Series Masoneilan * High Performance Butterfly Valves (HPBV) 2 GE Oil & Gas Table of Contents Foreword...3 Features...4 Numbering System...5 General
627 Series Pressure Reducing Regulators
627 Series Pressure Reducing Regulators Introduction The 627 Series direct-operated pressure reducing regulators (Figure 1) are for low and high-pressure systems. These regulators can be used with natural
Baumann Corrosion Resistant Control Valve
Product Bulletin D103337X012 Baumann 26000 Corrosion Resistant Control Valve The Baumann 26000 (figures 1 and 2) is a unique corrosion resistant control valve featuring a flangeless wafer valve body and