Solenoid interlocks AZM 161 range Schmersal. a 5,5. Pg11/M16x1,5

Transcription

1 .1 AZM 11 range Features Thermoplastic enclosure Manual and emergency release Long life Double insulated X High holding force, N N latching force Wiring compartment Actuation on de-energisation or energisation cable entries Actuating play. mm in direction of actuation Voltage variants 4 VAC/DC 11 VAC/DC VAC/DC Always state required supply voltage when ordering a, b 9 Pg11/M1x 1 Manual release Emergency release For manual release using M triangular key, available as accessory For maintenance, setting-up, etc. For cases of danger Fitting only within the guarded area Approvals H C D D USA CAN 9 Schmersal

2 .1 AZM 11 range Info The applicable ordering suffix is added at the end of the part number of the interlock. Available with connector on enquiry With M 1 x 1. cable entry, ordering suffix -M1 Actuation on de-energisation NO 4 NC NO NC Contacts/ Switch travel,4 1,, ,4 1,, With screw terminals With cage clamps AZM 11SK-4rk AZM 11CC-4rk AZM 11SK-rk AZM 11CC-rk Actuation on energisation NO 4 NC NO NC Contacts/ Switch travel,4 1,, ,4 1,, With screw terminals With cage clamps AZM 11SK-4rka AZM 11CC-4rka AZM 11SK-rka AZM 11CC-rka Notes Schmersal The contacts 1- and -4 are solenoid locking principle or de-energisation of the coil A1-A. Circuit diagrams show de-energised condition with actuator inserted ( in switch travel diagram). Interlocks with actuation on energisation may only be used in special cases after a thorough evaluation of the accident risk, since the guarding device can immediately be opened on failure of the electrical power supply or when the main switch is opened. Actuators must be ordered separately. A selection of suitable actuators can be found in.. 9

3 . Actuators Straight actuator AZM 11-B1 On hinged guards, minimum actuating radius 1 mm at 9 to the plane of the actuator Similarly, minimum actuating radius 1 mm in line with the plane of the actuator Rmin ø, 1 The axis of the hinge should be mm above the top edge of the solenoid interlock and in the same plane,7 7 Straight actuator AZM 11-B1E On hinged guards, minimum actuating radius 1 mm at 9 to the plane of the actuator Similarly, minimum actuating radius 1 mm in line with the plane of the actuator 14 Rmin.1 ø, ø The axis of the hinge should be mm above the top edge of the solenoid interlock and in the same plane Mounting details as for AZM 1-B1S 7 a b 11 Rmin.9 11 Rmin ,7 Adjustable actuator AZM 11-B Adjustable actuator for very small actuating radii. On hinged guards, minimum actuating radius 9 mm at 9 to the plane of the actuator, adjustable using an hexagonal key wrench. mm A/F (b) Similarly, minimum actuating radius 9 mm in line with the plane of the actuator, adjustable using an hexagonal key wrench. mm A/F (a) ø, The axis of the hinge should be 11 mm above the top edge of the solenoid interlock and in the same plane 4 a b 94 Schmersal

4 . Accessories Tamperproof screws Screw lengths Countersunk-head screws with unidirectional slots M x 1, Id. No.: 4 M x 1, Id. No.: 4 1 M x, Id. No.: 4 Supplied in sets of screws To mount the actuator Higher protection against tampering with interlock Protect against unauthorised removal of actuator Available in various lengths Slot sealing plug AZM 11 To cover unused actuator slots For protection against the ingress of course dirt Simple clip-in fitting Quantity required: per interlocking device Schmersal 9

5 . Accessories Mounting set MS AZM 11 For simple mounting on profile systems Mounting of the solenoid interlock parallel or right-angled to the safety guard Mounting plate AZ 1/AZM 11 7, 7 Hinweis Legend The mounting sets can only be used in conjunction with actuator AZM 11-B. Solenoid interlock and actuator are not included in delivery. 1 Roundhead screw M x 1 per ISO 7 Washer per DIN 1-, Counter sunk screw M x 1 per DIN Mounting plate AZ 1/AZM 11 U-profile AZM 11 Mounting angle AZM 11 7 Roundhead screw M x 1 per ISO 7 Not provided: Solenoid Interlock AZM 11 9 Actuator AZM 11-B U-profile AZM , xm , 1 1, 7 1 MS AZM 11 P Mounting parallel to safety guard 11,4 7, M 4 7 4,7 4 4, 4 9, 11, , MS AZM 11 R/P Mounting right-angled to safety guard 9 1 Mounting angle AZM x M Schmersal

6 .7 Technical data AZM 11 AZM 17 AZM 17-ST AZM 17i AZM 17i-ST AZM 17 SK Standards: IEC/EN /DIN VDE-; EN 1; BG-GS-ET-19 Enclosure material: Glass-fibre reinforced thermoplastic, self-extinguishing Actuator and latching bolt: Stainless steel 1.41 Protection class: IP 7 to IEC/EN 9/DIN VDE 47-1 Contact material: Silver Contact type: Changeover with double break Zb, or NC Changeover with double break Zb, or NC or 4 NC contacts, with galvanically with galvanically separated contact separated contact bridges bridges Switching system: A IEC ; B BG-GS-ET-19; slow action, NC contacts with positive break Termination: Screw terminals or Cut clamp terminals Connector M 1 x 1, cage clamps (IDC method) four pole max. 1. mm.7 1. mm flexible (incl. conductor ferrules) Ordering suffix SK: Screw terminals 1. mm flexible Rated impulse withstand voltage U imp : 4 kv Rated insulation voltage U i : V Thermal test current rating I th : 1 A Utilisation category: AC-1; DC-1 AC-1 Rated operating current/voltage I e /U e :. A/4 VDC; 4 A/ V 4 A/ VAC Max. fuse rating: A gl/gg D-fuse Positive break travel:. mm 11 mm Positive break force: 1 N for each NC N for each NC contact fitted contact fitted (depending on the setting of the ball latch) Solenoid duty rating: Continuous operation Rated control voltage U S : 4 VAC/DC 4 VAC/D or 11 VAC/DC, / Hz or 11 VAC/DC, / Hz or VAC/DC, / Hz or VAC/DC, / Hz Consumption: Max. 1 W Ambient temperature: C + C Mechanical life: > 1 million operations Holding force F max. :, N 1, N Holding force of integral ball latch: Latching force: N for Ordering Suffix r 1 Schmersal