Remote Oil Filter Mount with Integrated Thermostat

Size: px

Start display at page:

Download "Remote Oil Filter Mount with Integrated Thermostat"

Allan Jones
5 years ago
Views:

1 Remote Oil Filter Mount with Integrated Thermostat Part No. ENV-170 Made in USA Important: Read these instructions in their entirety prior to installation. Rev

2 Parts List ITEM QUANTITY PART # DESCRIPTION 1 1 ENV-170 Thermostatic Remote Oil Filter Mount 2 1 HSC-1039 M22x1.0 Oil Filter Screw 3 1 ENV Mounting Bracket 4 2 HSC-1040 Mounting Bracket Screw 4 OM-10-XX -10AN O-ring Adapter Fitting (Optional)* * Available in -6AN, -8AN, -10AN, -12AN, 3/8 Hose-Barb, 1/2 Hose-Barb Product Information Temperature Rating Information Part Number ENV-170-T1 ENV-170-T2 ENV-170-T4 ENV-170-T7 Typical Stabilization Temperature (At Outlet) 14 F +/- 2 F (63 C +/- 1 C) 16 F +/- 2 F (74 C +/- 1 C) 18 F +/- 2 F (8 C +/- 1 C) 21 F +/- 2 F (101 C +/- 1 C) Activation Temperature (At Outlet) 140 F +/- 2 F (60 C +/- 1 C) 160 F +/- 2 F (71 C +/- 1 C) 180 F +/- 2 F (82 C +/- 1 C) 212 F +/- 2 F (100 C +/- 1 C) 2

3 Technical Information Max. Operating Temperature Min. Operating Temperature Max. Recommended Pressure 302 F (10 C) -22 F (-30 C) 300 PSI (20.68 bar) Max. Oil Filter Gasket O.D. 3.2 Dimensions (W x H x D) 3.2 x 2.1 x 4.37 (8.26 cm x.33 cm x cm) Fitting Ports -10AN SAE J Weight (no adapter fittings) 18.3 oz (18.8 g) Housing Material Housing Finish Oil Filter Screw Material Oil Filter Screw Finish Oil Filter Screw Thread Spec. Bracket Material Bracket Finish CNC-Machined 6061-T6 Billet Aluminum MIL-A-862 Type II Anodizing, Black 410 Stainless Steel Plain M22x1.0, 6h Thread Class 8-Gauge 02 Aluminum MIL-A-862 Type II Anodizing, Black Bracket Hardware Material Zinc-Plated Alloy Steel, Grade 10.9 Bracket Hardware Thread Valve Material Valve Finish Spring Material Spring Finish Thermal Actuator Material Estimated Service Life Product Notes M6x1.00, 6g Thread Class CNC-Machined 6061-T6 Billet Aluminum Plain 316 Stainless Steel Ultrasonic Citric Acid Passivation Brass Body, Zinc-Plated Steel Ram > 10,000 Heat Cycles Not recommended for use with corrosive fluids. The integrated thermostat accelerates warm-up and prevents overcooling when used with an oil cooler. Under no circumstances can the thermostat fail in such a way that oil flow to the engine or transmission is blocked. Thermostat is re-buildable. Should the unit fail, it can be shipped back to Improved Racing for a rebuild with a new thermal element and seals. For a list of compatible filters, turn to Appendix A, located on Page 7 of this manual. 3

4 Flow Diagram and Operation 1. The thermostat bypasses the oil cooler until the fluid reaches the rated activation temperature. 2. At the activation temperature, the bypass valve gradually begins to close, forcing oil through the cooler and allowing it to cool. If the oil cooler s heat extraction rate is sufficient, the fluid will tend to stabilize at the rated stabilization temperature at the outlet. COOL OIL 94-98% OF OIL FLOW BYPASSES THE OIL OIL ALWAYS FLOWS THROUGH FILTER FIRST HOT OIL 100% OF OIL FLOW NOW FLOWS THROUGH OIL Figure 1 - Oil Flow Diagram 4

5 Flow Configurations The standard flow configuration (Figure 2) or alternate flow configuration (Figure 3) may be used. Select the configuration that best suits your setup. Tip: The standard flow configuration is recommended. ENV F THERMOSTAT PAT. PENDING MADE IN USA ENV F THERMOSTAT PAT. PENDING MADE IN USA OIL Figure 2 - Standard Flow Configuration Mounting the Filter Mount OIL Figure 3 - Alternate Flow Configuration Attach the bracket to the filter mount in one of the configurations shown below in Figure 4. Secure the remote filter mount to a sturdy part of the vehicle such as the frame or firewall using M8 or /16 screws and hardware. Figure 4 - Mounting Bracket Configurations

6 Installation Instructions 1. Install the AN adapter fittings into the filter mount. Tip: Lubricate the -AN fitting O-rings with engine oil to prevent O-ring damage. Tip: Use aluminum -AN fitting wrenches to avoid damaging the fittings. 2. Secure the filter mount to the vehicle with the mounting bracket provided. 3. Configure and assemble the oiling system lines for the vehicle. 4. Fill the oil cooler with oil prior to connecting the lines.. Connect and tighten the system lines. DO NOT overtighten. Tip: Use aluminum -AN fitting wrenches to avoid damaging the fittings. 6. Secure the oil cooler to the vehicle. 7. Refill the engine oiling system and install a new oil filter. Tip: Pre-fill the oil filter with engine oil and lubricate the oil filter seal with engine oil. 8. Remove the fuel pump fuse(s) or disconnect the ignition circuit. 9. Crank the engine over to build oil pressure. 10. Replace any fuse(s) removed and/or reconnect the ignition circuit. 11. Start the vehicle and inspect for leaks. 12. Turn-off the vehicle and inspect the engine oil level. Add oil if necessary. 13. Re-inspect the oil lines and fittings for leaks after 100 miles of driving. Installation is now complete. Thank you for purchasing an Improved Racing product! 6

7 Appendix A Recommended M22x1.0 Oil Filters For the most up-to-date list of compatible filters, visit the product page at Brand Part Number By-Pass Relief Valve (PSI) Anti- Drain Back Valve Height x OD (in) Approximate Volume (in³) Wix WL7421 No No 6.69 x Wix WL Yes.61 x Fram PH3616 Yes No.14 x AC-Delco PF Purolator L Wix No.21 x Royal Purple Yes Yes 4.00 x K&N HP-2010 Yes Yes 4.00 x Fram PH2 12 Yes 3.98 x Purolator L Yes 3.73 x microgreen MG421-8 Yes Yes 3.76 x AC-Delco PF Wix Yes 3.84 x Wix Yes 3.74 x Mobil 1 M1-210 Yes Yes 3.7 x Mobil 1 M1-212 Yes Yes 4.87 x Royal Purple Yes Yes 4.87 x Bosch 302 No Yes 4.08 x Purolator L Yes 4.08 x Fram PH107 Yes Yes 4.06 x Mobil 1 M1-113 Yes Yes 3.62 x Royal Purple Yes Yes 3.62 x Wix Yes 4.09 x

Remote Oil Filter Mount

Remote Oil Filter Mount Part No. ENV-140 Made in USA Important: Read these instructions in their entirety prior to installation. Rev 170925 Parts List 1 x ENV-140 remote filter mount 1 x M22x1.50 oil filter