600-8,000 LBS. CAPACITY

Size: px
Start display at page:

Download "600-8,000 LBS. CAPACITY"

Transcription

1 00 -,000 LS. CAPACITY TRAILER RUNNING GEAR

2 Introduction This information is intended as a guide for the proper specification and application of Dexter Axle running gear, associated components and accessories. Dexter offers a full line of trailer axles that can be used in many different applications. When specifying any pre-engineered components such as axles, it is the responsibility of the trailer designer to insure compatibility with the vehicle and all of its sub systems. Important Information The information presented is meant to assist trailer manufacturers in the specification of their running gear components. Dexter Axle does not warrant that the information given constitutes an approved trailer design or application. Dynamic loading, travel requirements unique to the trailer design, unusual service conditions, trailer configurations, unequal load distribution, hitch or coupler arrangements and towing vehicle suspension characteristics can significantly affect the performance of any trailer axle and/or suspension systems. It remains the responsibility of the trailer manufacturer to evaluate, specify and test their trailer/running gear combination before production and to certify it as such. While the information presented at the time of this writing is current, it is subject to change as designs and components evolve over time. Disclaimer of Warranty and Limitation of Liability All users of this product catalog acknowledge that the information presented is significantly affected by factors within the exclusive knowledge of the user including, among other things, service conditions, trailer configurations, load distributions, hitch and coupler arrangements and tow vehicle suspension characteristics, that the users have independently investigated these factors and have solely relied on those investigations when using this catalog, and that it is the responsibility of the user to adequately specify, evaluate and test its trailer/running gear combinations. DEXTER AXLE DISCLAIMS ALL WARRANTIES, WHETHER WRITTEN, ORAL OR IMPLIED, IN FACT OR IN LAW (INCLUDING ANY WARRANTY OF MERCHANTAILITY OR FITNESS FOR A PARTICULAR PURPOSE), ASSOCIATED WITH THE USE OF THE CATALOG AND WITH ANY INFORMATION PRESENTED Y THIS CATALOG. Dexter Axle shall not be liable in damages (whether compensatory, punitive, direct, indirect, special, incidental or consequential) to any user of this catalog under contract, tort, strict liability or any other theory of liability, and any user agrees to indemnify and hold Dexter Axle harmless from any and all claims, actions or other proceedings (including attorney fees and court costs) arising out of the use of this catalog to the extent said claims, actions or other proceedings do not arise out of the sole and exclusive negligence of Dexter Axle. Load Ratings The maximum load carrying capacity of any assembly is limited to the lowest load rating of any individual component selected. For instance, the load rating of a pair of wheels may be lower than other axle components selected. If this is the case, the load carrying capacity of the axle assembly is reduced accordingly. As a specific example, if a pair of wheels is rated at 100 pounds each and is used with other components rated at 4000 pounds per axle, the maximum load capacity is limited to 3000 pounds. If two tires are rated at 1400 pounds each and are used on this assembly, the maximum load carrying capacity is limited to 00 pounds. Axle Orientation When working with trailer running gear, it is important to understand the various features and descriptions of the equipment. Most trailer axles are directional by nature, that is, it is imperative that they be installed onto the trailer in the proper manner to ensure brake functioning and correct wheel alignment. The front of the axle must be oriented toward the front of the trailer. The convention used to define right and left is based on viewing the trailer from the rear and facing in the direction of forward travel.

3 Introduction Features to help identify the front of the axle: Electric brake wires exit brake backing plates toward the rear of the axle. 1¹ ₄" hydraulic brakes have view ports through the dust shield on the back of the assembly. Where the brake lining is visible in the view port, that will indicate the rear or secondary shoe which is always oriented toward the rear of the axle. Slipper springs have the spring eye at the front of the axle. Leaf spring axles with inner wiring have the wires exit the tube toward the rear of the axle. Torflex axles have the wheel center trailing behind the axle tube. Axles using ³ ₄" spherical ball seat wheel nuts will have right and left handed threads. The right handed thread must be on the right end or curb side of the axle while the left handed thread will be on the left end or road side of the axle. Stub Axle Disclaimer A stub axle is described as a trailer axle spindle, welded to a short length of tubing. Stub axles may be specified and purchased as plain spindle/tube weldments or they may be fully assembled wheel end units, with or without trailer brakes. These incomplete axles are sold to manufacturers who wish to incorporate them into a variety of applications such as specialty vehicular axles, belt tensioning devices, machinery pivot points, etc. Dexter Axle has no control of the design intent of these special applications and therefore cannot apply a rating or capacity to these components. The spindle/tube connection has been designed for suitable stress levels when used in a trailer axle, mounted to an approved suspension system and loaded to no more than the stated capacity. The use of all or part of the product for applications other than its intended purpose may not be appropriate. It is the customers responsibility to determine the efficacy and safety of their particular application. Torflex axles can also be purchased as stub axles. This type of axle incorporates a self-contained suspension system. They can be specified as stub assemblies that will be rated for capacity when fitted with approved mounting brackets. The stated capacity will be based on the lowest rated component in each assembly. These stub assemblies are essentially half axles that are intended to be mounted to the trailer chassis independent of each other. The trailer manufacturer must assume responsibility for the integrity of the attachment as well as the final wheel alignment since independent mounting puts these critical aspects out of Dexter s control. If used in pairs of unequal capacity, the trailer manufacturer should assign a Gross Axle Weight Rating of not more than two times the capacity of the lower rated sub assembly.

4 Table of Contents Lbs. Capacity... # Torflex... 4 Torflex Application Information... Hub Groups... rakes Lbs. Capacity... # Torflex / D0 Leaf Spring Torflex Application Information... 1 Leaf Spring Application Information Hub Groups... 1 rakes Lbs. Capacity... #10, #10F & #10L Torflex / D30 & D3 Leaf Spring... 1 Torflex Application Information... 0 Leaf Spring Application Information... Hub Groups... 4 rakes Lbs. Capacity... #11 Torflex / D44, D, & D0 Leaf Spring Torflex Application Information Leaf Spring Application Information Hub Groups... 4 rakes Lbs. Capacity... #1 & #1T Torflex / D0 & D0 Leaf Spring... Torflex Application Information... Leaf spring Application Information... 3 Hub Groups... rakes... Airflex Suspension System Lbs. Capacity... #1V Torflex / D Leaf Spring... 3 Torflex Application Information... 4 Leaf Spring Application Information... Hub Groups... rakes... 0 Airflex Suspension System Lbs. Capacity...#13 & #13T Torflex / D0 Leaf Spring... 4 Torflex Application Information... Leaf Spring Application Information... Hub Groups... rakes Airflex Suspension System Miscellaneous Wheels and Tires Hanger and Attaching Parts Kits Torflex Installation Dexter Axle Limited Warranty Video Gallery Dexter Axle Video Gallery... 10

5 General Applications lbs. capacity Axle Types Lbs. Capacity Ideal application for light utility, for hauling personal watercraft and motorcycles Complete service manual Heavy duty 1¹ ₁₆" spindle design Precision machined steel spindles and integral cast iron hub/drums Short version spindle for trailers with extremely short overhangs " x 1¹ ₄" electric and " x 1³ ₄" hydraulic brakes Electric brakes are available with and without parking feature Standard grease lubrication; E-Z Lube option Lower cost CAUTION: Triple axle assemblies are NOT recommended for # Torflex axles. Totally rubber-cushioned for smooth, quiet, independent ride Easy installation with less maintenance Less transfer of road shock which insulates cargo from road shocks and vibration Rubber cords compounded for maximum dependability and durability Load-carrying cross member Self-damping action Independent wheel suspension system year limited warranty on suspension system Low profile for maximum road clearance Various starting angles to control trailer height Low profile brackets available Rubber cushioning eliminates metal-to-metal contact Shock absorption provided by the natural hysteresis of rubber Single or tandem axle assemblies Durable, wear-resistant components 4

6 Torflex Application Information Start Angle Articulation Dimensions Dimensions are for low profile, top mount only. Side mount is.1" higher. Allow 3" bump clearance from full load. racket Profile Forward No Load Full Load Shock Load H L H L H L Left Hand Assembly Shown Arm Length DEXTER Axle Location L H Top of racket Center of Spindle Start Angle lbs. capacity 4 Down 3 Down. Down 10 Down Low Low Low Low # Overhang Per Side Spindle Min. Max. Short 4.".04" Standard.00".04" 0 Low Up. Up Low Low Note: Positive numbers in the H column indicate the spindle is ELOW the top of the bracket. Conversely, negative numbers are AOVE the top of the bracket. Full Load Dimensions Dimensions are for low profile, top mount only. Side mount is.1" higher. Allow 3" bump clearance from full load. C Top of racket H E D C Top of racket H E D 10 Dn, 0, 10 Up,. Up. Dn, 4 DN Start Angle * * * 4 Down. Down 10 Down 0 10 Up. Up Tire D E H C H C H C H C H C H C ST1/0R x Columns D and E are dimensional examples only: * D Static Loaded Radius ** E Inflated Radius

7 Torflex Application Information lbs. capacity racket Dimensions Forward For Wiring Access olt Size J A G A E D Low Profile Right Hand Side of Axle Shown C F 1/ G Side Mount Hanger # racket Dimensions Low A C.00 D. E F. G.00 J 1. olt Size ¹ ₂" bolt Tube Size 1.

8 440 and 4 Hub Group Exp00_ A 4 0 A& A& 11A 11 A 4 A lbs. capacity E-Z Lube axles with spindle washer prior to mid 00 Grease Lube Parts Item Part No. Description Grease Seal 1A Grease Seal for E-Z Lube L444 Inner earing Cone L4410 Inner earing Cup L4410 Outer earing Cup L444 Outer earing Cone Spindle Nut Cotter Pin (not used with E-Z Lube ) Grease Cap A Grease Cap for E-Z Lube Rubber Plug for E-Z Lube Wheel olt Tang Washer for E-Z Lube (before 00) 11A Spindle Washer for E-Z Lube (before 00) Spindle Washer for E-Z Lube (after 00) Spindle Nut Retainer for E-Z Lube (after 00) Special Jam Nut for E-Z Lube (after 00) rakes Item Part No. Description 0 K /K LH/RH "x1¼" Electric ns K /K LH/RH "x1¼" Electric w/park ns K3-3-00/K LH/RH "x1¾" Hydraulic Uni-servo ns - not shown Note: Spindle is not available for resale. Hubs Item Part No. Description olt Circle Hubs and Drums ns ½" Studs, elec. brakes ONLY 4 on 4.00 ns ½" Studs, hyd. brakes ONLY 4 on 4.00 A ½" Studs, elec. brakes ONLY on ½" Studs, hyd. brakes ONLY on ½" Tapped, elec. brakes ONLY 4 on 4.00 ns ½" Tapped, elec. brakes ONLY on 4.0 ns ½" Tapped, hyd. brakes ONLY on 4.0 Plain Hubs ns ½" Studs 4 on ½" Tapped 4 on 4.00 A ½" Studs, "-1" wheels ONLY on ½" Studs, 13"-1" wheels ONLY on 4.0 ns ½" Tapped, "-1" wheels ONLY on 4.0 ns ½" Tapped, 13"-1" wheels ONLY on 4.0 Studs & Wheel Nuts Item Part No. Description ½-0 Wheel olt ½-0 0 Cone Nut ½-0 Press-in Stud

9 " x 1¹ ₄" Electric rake lbs. capacity 1 14 X1E_ Torflex CSA approved at 000#/11.3 SLR; 00#/10. SLR Sprung CSA approved at 000#/1. SLR; 00#/10. SLR Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate Assembly (includes items #11, 13) Shoe Hold Down Clip 3 K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining # Secondary Shoe & Lining Retractor spring LH Actuating Lever Arm RH Actuating Lever Arm Anchor Post Clip Wire Clip For brakes manufactured after 4/1/0 K Magnet Kit Contains: 1 # Magnet 1 # Magnet Clip 1 # Magnet Spring Adjusting Screw Spring Adjusting Screw rake Mounting olt - Press-in * rake Mounting Nut Stabilizer racket Adjuster Slot Plug For brakes manufactured after /1/ Shoe Centering Spring * Not included with complete brake assembly. Item sold separately. This brake is rated to a maximum capacity of 00 lbs. / pair

10 " x 1¹ ₄" Electric rake With Parking Feature X1EPF_ CSA approved at 000#/11.3 SLR; 00#/10. SLR lbs. capacity Electric Parking rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly Shoe Hold Down Clip 3 K Shoe & Lining Kit Contains: 1 # Primary Shoe &Lining # Secondary Shoe &Lining Retractor spring For brakes manufactured after 4/1/0 K Magnet Kit Contains: 1 # Magnet 1 # Magnet Clip 1 # Magnet Spring Adjusting Screw Spring Adjusting Screw rake Mounting olt - Press-in * rake Mounting Nut Stabilizer racket Adjuster Slot Plug For brakes manufactured after /1/ Shoe Centering Spring * Not included with complete brake assembly. Item sold separately. Electric Parking rake LH acking Plate & Lever Arm (includes items #-30,, 11, 13) RH acking Plate & Lever Arm (includes items #-30,, 11, 13) LH Pivot Pin & Cam Sub-Assembly RH Pivot Pin & Cam Sub-Assembly Lever Self Locking Nut Washer Anchor Pin Self Locking Nut Spacer LH Lever Arm & Cam Assembly RH Lever Arm & Cam Assembly Lever Stop Wire Clip This brake is rated to a maximum capacity of 00 lbs. / pair

11 " x 1³ ₄" Hydraulic rake lbs. capacity 1 1 X1-H_ CSA approved at 00#/11. SLR Note: Uni-Servo brakes to be used with surge actuator 1 1 Hydraulic rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate rake Mounting olt - Press-in Wheel Cylinder Assembly - LH (includes item #1) Wheel Cylinder Assembly - RH (includes item #1) Anchor Post Lock Washer Counter Sunk Cap Screw Hex Nut Socket Head Cap Screw K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Spring 4 # Shoe Hold Down Spring Cup # Shoe Hold Down Pin Retractor spring Adjusting Screw Spring Adjuster Screw Assembly Adjuster Slot Plug leeder Screw mm Thread (brakes before 1/) leeder Screw mm Thread (brakes after 1/) * rake Mounting Nut * Not included with complete brake assembly. Item sold separately. This brake is rated to a maximum capacity of 00 lbs. / pair 10

12 General Applications Axle Types lbs. capacity Lbs. Capacity Complete service manual Heavy duty 1¹ ₁₆" spindle design Precision machined steel spindles and integral cast iron hub/drums CSA approved " x 1¹ ₄" electric and " x 1³ ₄" hydraulic brakes Electric brakes are available with and without parking feature Standard grease lubrication; E-Z Lube option Press-in wheel studs Inner wiring system for easier installation and protection of brake wiring d0 leaf spring Designed for light-capacity trailers Designed for travel trailers being towed by smaller automobiles High strength 1³ ₄" diameter tube for straight axles and ³ ₈" for drops Straight or Drop spindles (4" drop only) High quality alloy steel springs in a variety of capacities Single, tandem, or triple axle assemblies with equalized suspensions Slipper spring or double eye leaf spring suspension Optional hanger and attaching parts kits available Durable, wear-resistant components year limited warranty Designed for fold-down campers, light utility, boat trailer applications Totally rubber-cushioned for smooth, quiet, independent ride Easy installation with less maintenance Less transfer of road shock which insulates cargo from road shocks and vibration Rubber cords compounded for maximum dependability and durability Load-carrying cross member Self-damping action Independent wheel suspension system year limited warranty on suspension system Low profile for maximum road clearance Various starting angles to control trailer height High and low profile brackets with optional mounting brackets available Rubber cushioning eliminates metal-to-metal contact Shock absorption provided by the natural hysteresis of rubber Single or tandem axle assemblies Durable, wear-resistant components CAUTION: Triple axle assemblies are NOT recommended for # Torflex axles. 11

13 Torflex Application Information lbs. capacity Start Angle 4 Down 3 Down. Down 10 Down Articulation Dimensions Dimensions are for top mount only. Side mount is.1" higher. Allow 3" bump clearance from full load. racket Profile Forward No Load Full Load Shock Load H L H L H L Low High Low High Low High Low High Left Hand Assembly Shown DEXTER Arm Length Axle Location L # Overhang Per Side Spindle Min. Max. Short.00" 10.0" Standard.0" 10.0" H Top of racket Center of Spindle Start Angle 0 Low High Up. Up Low High Low High Note: Positive numbers in the H column indicate the spindle is ELOW the top of the bracket. Conversely, negative numbers are AOVE the top of the bracket. Full Load Dimensions Dimensions are for low profile, top mount only. High profile brackets are." higher. Side mount is.1" higher. Allow 3" bump clearance from full load. C Top of racket H E D C Top of racket H E D 10 Dn, 0, 10 Up,. Up. Dn, 4 DN 1 Start Angle * * * 4 Down. Down 10 Down 0 10 Up. Up Tire D E H C H C H C H C H C H C ST1/0R x Columns D and E are dimensional examples only: * D Static Loaded Radius ** E Inflated Radius

14 Torflex Application Information racket Dimensions Forward For Wiring Access olt Size J A G Right Hand Side of Axle Shown C A E D Low Profile F 1/ G lbs. capacity Side Mount Hanger # racket Dimensions Low High A C D.. E F. 3. G J N P.4.4 Q olt Size ¹ ₂" bolt Tube Size.1.1 P E F High Profile N Q 13

15 Leaf Spring Application Information lbs. capacity Double Eye Springs For Standard 33" Axle Spacing Single A/P-1-00 Tandem A/P Triple A/P Spring Length 1" 4" " A C D E For Optional 3" Axle Spacing Tandem A/P-4-00 Triple A/P Spring Length 1" 4" " C D E D0 Overhang Per Side Min. Max. Straight."." Drop.".00" A,, E Hanger Spacing C Axle Spacing D Axle Location H Center of Spindle Y Frame Height Z Top of Tire to ottom of Frame SLR Static Load Radius To determine these values, contact your local sales engineer or distributor to run ProSpec. Z Y SLR Z Y H SLR Forward D E Z Y SLR H C D A H D C C Double Eye Axle Assemblies Hanger Kits Quantity Per Kit Part No. Description Height HGR HGR HGR-4-00 HGR-4-00 HGR Hanger 3." Front Hanger 1.44" Front Hanger.0" Center Hanger 3." Rear Hanger.1" Attaching Parts Kits Part No. Description A/P-1-00 A/P A/P-4-00 A/P A/P Flange Locknut Shackle olt Equalizer Equalizer Equalizer Equalizer Shackle Link Shackle Link, Long Shackle Link Assembly Shackle Link Assembly, Long For 3" axle spacing using " springs Slipper Spring Axle Assemblies Hanger Kits Part No. Description Ht. HGR Front Hanger 3." Rear Hanger 1.44" Attaching Parts Kits Part No. Description A/P Locknut Shackle olt Slipper Springs A/P / DIA. H Z SLR Y Some combinations of hangers and spring mountings may result in insufficient bump clearance. Refer to the Miscellaneous section for additional hanger kits, A/P kits, or other tires Forward 14

16 440 and 4 Hub Group Exp00_ A 4 0 A& A& 11A 11 A 4 A lbs. capacity E-Z Lube axles with spindle washer prior to mid 00 Grease Lube Parts Item Part No. Description Grease Seal 1A Grease Seal for E-Z Lube L444 Inner earing Cone L4410 Inner earing Cup L4410 Outer earing Cup L444 Outer earing Cone Spindle Nut Cotter Pin (not used with E-Z Lube ) Grease Cap A Grease Cap for E-Z Lube Rubber Plug for E-Z Lube Wheel olt Tang Washer for E-Z Lube (before 00) 11A Spindle Washer for E-Z Lube (before 00) Spindle Washer for E-Z Lube (after 00) Spindle Nut Retainer for E-Z Lube (after 00) Special Jam Nut for E-Z Lube (after 00) rakes Item Part No. Description 0 K /K LH/RH "x1¼" Electric ns K /K LH/RH "x1¼" Electric w/park ns K3-3-00/K LH/RH "x1¾" Hydraulic Uni-servo ns - not shown Note: Spindle is not available for resale. Hubs Item Part No. Description olt Circle Hubs and Drums ns ½" Studs, elec. brakes ONLY 4 on 4.00 ns ½" Studs, hyd. brakes ONLY 4 on 4.00 A ½" Studs, elec. brakes ONLY on ½" Studs, hyd. brakes ONLY on ½" Tapped, elec. brakes ONLY 4 on 4.00 ns ½" Tapped, elec. brakes ONLY on 4.0 ns ½" Tapped, hyd. brakes ONLY on 4.0 Plain Hubs ns ½" Studs 4 on ½" Tapped 4 on 4.00 A ½" Studs, "-1" wheels ONLY on ½" Studs, 13"-1" wheels ONLY on 4.0 ns ½" Tapped, "-1" wheels ONLY on 4.0 ns ½" Tapped, 13"-1" wheels ONLY on 4.0 Studs & Wheel Nuts Item Part No. Description ½-0 Wheel olt ½-0 0 Cone Nut ½-0 Press-in Stud 1

17 " x 1¹ ₄" Electric rake lbs. capacity 1 14 X1E_ CSA approved at 000#/11.3 SLR; 00#/10. SLR Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate Assembly (includes items #11, 13) Shoe Hold Down Clip 3 K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining # Secondary Shoe & Lining Retractor spring LH Actuating Lever Arm RH Actuating Lever Arm Anchor Post Clip Wire Clip For brakes manufactured after 4/1/0 K Magnet Kit Contains: 1 # Magnet 1 # Magnet Clip 1 # Magnet Spring Adjusting Screw Spring Adjusting Screw rake Mounting olt - Press-in * rake Mounting Nut Stabilizer racket Adjuster Slot Plug For brakes manufactured after /1/ Shoe Centering Spring * Not included with complete brake assembly. Item sold separately. This brake is rated to a maximum capacity of 00 lbs. / pair 1

18 " x 1¹ ₄" Electric rake With Parking Feature X1EPF_ CSA approved at 000#/11.3 SLR; 00#/10. SLR lbs. capacity Electric Parking rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly Shoe Hold Down Clip 3 K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining # Secondary Shoe & Lining Retractor spring For brakes manufactured after 4/1/0 K Magnet Kit Contains: 1 # Magnet 1 # Magnet Clip 1 # Magnet Spring Adjusting Screw Spring Adjusting Screw rake Mounting olt - Press-in * rake Mounting Nut Stabilizer racket Adjuster Slot Plug For brakes manufactured after /1/ Shoe Centering Spring * Not included with complete brake assembly. Item sold separately. Electric Parking rake LH acking Plate & Lever Arm (includes items #-30,, 11, 13) RH acking Plate & Lever Arm (includes items #-30,, 11, 13) LH Pivot Pin & Cam Sub-Assembly RH Pivot Pin & Cam Sub-Assembly Lever Self Locking Nut Washer Anchor Pin Self Locking Nut Spacer LH Lever Arm & Cam Assembly RH Lever Arm & Cam Assembly Lever Stop Wire Clip This brake is rated to a maximum capacity of 00 lbs. / pair 1

19 " x 1³ ₄" Hydraulic rake lbs. capacity 1 1 X1-H_ CSA approved at 00#/11. SLR Hydraulic rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate rake Mounting olt - Press-in Wheel Cylinder Assembly - LH (includes item #1) Wheel Cylinder Assembly - RH (includes item #1) Anchor Post Lock Washer Counter Sunk Cap Screw Hex Nut Socket Head Cap Screw K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Spring 4 # Shoe Hold Down Spring Cup # Shoe Hold Down Pin Retractor spring Adjusting Screw Spring Adjuster Screw Assembly Adjuster Slot Plug leeder Screw mm Thread (brakes before 1/) leeder Screw mm Thread (brakes after 1/) * rake Mounting Nut * Not included with complete brake assembly. Item sold separately. This brake is rated to a maximum capacity of 00 lbs. / pair 1

20 General Applications Axle Types Lbs. Capacity Complete service manual Precision machined steel spindles and integral cast iron hub/drums Press-in wheel studs 10" x 1¹ ₂" and 10" x ¹ ₄" CSA approved electric brakes, CSA approved uni-servo and free backing hydraulic brakes Electric and hydraulic brakes are available with and without parking feature Hydraulic free backing brakes available Hydraulic disc brakes available Standard grease lubrication; E-Z Lube option Inner wiring system for easier installation and protection of brake wiring d30 & D3 leaf spring lbs. capacity 10 10F 10L Totally rubber-cushioned for smooth, quiet, independent ride Easy installation with less maintenance Less transfer of road shock which insulates cargo from road shocks and vibration Rubber cords compounded for maximum dependability and durability Load-carrying cross member Self-damping action Independent wheel suspension system year limited warranty on suspension system Low profile for maximum road clearance Various starting angles to control trailer height High and low profile brackets with optional mounting brackets available Rubber cushioning eliminates metal-to-metal contact Shock absorption provided by the natural hysteresis of rubber Single or tandem axle assemblies Durable, wear-resistant components Straight or Drop spindles (3") D30 Straight or Drop spindles (4" and " drop) D3 High strength ³ ₈" diameter tube High quality alloy steel springs in a variety of capacities Single, tandem, or triple axle assemblies with equalized suspensions Slipper spring or double eye leaf spring suspension Optional hanger and attaching parts kits available Durable, wear-resistant components year limited warranty CAUTION: Triple axle assemblies are NOT recommended for #10, #10F and #10L Torflex axles. 1

21 Torflex Application Information lbs. capacity 10 Start Angle 4 Down 3 Down. Down 10 Down 0 10 Up. Up 10 10F racket Profile 10F 10L Articulation Dimensions Dimensions are for top mount only. Side mount is.1" higher. Allow 3" bump clearance from full load. Forward No Load Full Load Shock Load H L H L H L Low High Low High Low High Low High Low High Low High Low High L Left Hand Assembly Shown DEXTER Arm Length Axle Location L Note: Positive numbers in the H column indicate the spindle is ELOW the top of the bracket. Conversely, negative numbers are AOVE the top of the bracket. Full Load Dimensions Dimensions are for low profile, top mount only. High profile brackets are." higher. Side mount is.1" higher. Allow 3" bump clearance from full load. H Top of racket Center of Spindle Start Angle Overhang Per Side Spindle Min. Max. Max. Capacity #10 Standard w/drum.30" 11.0" 300 #10 w/disc rake." 11.0" 300 #10F w/drum.30" 10.0" 4000 #10L w/drum." 13." 3000 C Top of racket H E D C Top of racket H E D 10 Dn, 0, 10 Up,. Up. Dn, 4 DN Start Angle * * * 4 Down. Down 10 Down 0 10 Up. Up Tire D E H C H C H C H C H C H C ST1/0R ST0/R ST/R Columns D and E are dimensional examples only: * D Static Loaded Radius ** E Inflated Radius 0

22 Torflex Application Information 10 10F 10L racket Dimensions Forward For Wiring Access olt Size J A G Right Hand Side of Axle Shown C A E D Low Profile F 1/ G lbs. capacity Side Mount Hanger #10 racket Dimensions Low High A C D E F G.0.0 J N P Q olt Size ⁵ ₈" bolt Tube Size.. P E F High Profile N Q 1

23 Leaf Spring Application Information lbs. capacity Double Eye Springs For Standard 33" Axle Spacing Single A/P-1-00 Tandem A/P Triple A/P Spring Length 1" 4" " A C D E For Optional 3" Axle Spacing Tandem A/P-4-00 Triple A/P Spring Length 1" 4" " C D E D3 Overhang Per Side Min. Disc* Max. Straight.".".00" 4" Drop.00".".00" " Drop.".".00" 3" Dia. Straight."." 11.0" 3" Dia. Drop.00"." 11.0" * Minimum overhang with disc brakes D30 Overhang Per Side Min. Max. Straight.3".00" 3" Drop.00".00" Z Y SLR Forward H Z Y SLR D E H Z Y SLR C D A H D C C Double Eye Axle Assemblies Hanger Kits Quantity Per Kit Part No. Description Height HGR HGR HGR-4-00 HGR-4-00 HGR Hanger 3." Front Hanger 1.44" Front Hanger.0" Center Hanger 3." Rear Hanger.1" Attaching Parts Kits Part No. Description A/P-1-00 A/P A/P-4-00 A/P A/P Flange Locknut Shackle olt Equalizer Equalizer Equalizer Equalizer Shackle Link Shackle Link, Long Shackle Link Assembly Shackle Link Assembly, Long For 3" axle spacing using " springs

24 Leaf Spring Application Information Z Y Z Y Z Y SLR SLR SLR D D A H H H C Forward E Slipper Springs Single Tandem Triple A/P A/P-0-00 A/P-1-00 A/P A/P A C D E Note: All " wide slipper springs For 33." axle spacing For 3" axle spacing A,, E Hanger Spacing C Axle Spacing D Axle Location H Center of Spindle Y Frame Height Z Top of Tire to ottom of Frame SLR Static Load Radius To determine these values, contact your local sales engineer or distributor to run ProSpec lbs. capacity D C E Slipper Spring Axle Assemblies Hanger Kits Quantity Per Kit Part No. Description Height HGR HGR-0-00 HGR Front Hanger 4." Center Hanger 3.0" Rear Hanger 4.00" Attaching Parts Kits Part No. Description A/P A/P-0-00 A/P-1-00 A/P A/P ⁹ ₁₆-1 Locknut Keeper Nut Equalizer Nut Equalizer olt Keeper olt Spring Eye olt Equalizer Equalizer For 33." axle spacing For 3" axle spacing Some combinations of hangers and spring mountings may result in insufficient bump clearance. Refer to the Miscellaneous section for additional hanger kits, A/P kits, or other tires. 3

25 D30 and #10L 4 Hub Group lbs. capacity ExpD30_ A Grease Lube Parts Item Part No. Description Grease Seal for E-Z Lube LM04 Inner earing Cone LM010 Inner earing Cup L4410 Outer earing Cup L444 Outer earing Cone Spindle Nut Cotter Pin Grease Cap A Grease Cap for E-Z Lube Rubber Plug for E-Z Lube Spindle Washer Special Jam Nut for E-Z Lube (after 00) Spindle Nut Retainer for E-Z Lube (after 00) Hubs Item Part No. Description olt Circle Hubs and Drums ½" Stud on 4.0 Studs & Wheel Nuts Item Part No. Description ½-0 Pressed Wheel Stud ½-0 0 Cone Nut 10" x 1¹ ₂" rakes Item Part No. Description 0 0 K3-4-00/K K3-4-00/K LH/RH Electric LH/RH Nev-R-Adjust Note: Spindle is not available for resale. 4

26 D3, #10 4 and Other Hub Group ExpD3_ A lbs. capacity Grease Lube Parts Item Part No. Description Grease Seal for E-Z Lube L14 Inner earing Cone L111 Inner earing Cup L4410 Outer earing Cup L444 Outer earing Cone Spindle Nut Cotter Pin Grease Cap A Grease Cap for E-Z Lube Rubber Plug for E-Z Lube Spindle Washer Special Jam Nut for E-Z Lube (after 00) Spindle Nut Retainer for E-Z Lube (after 00) 10" x ¹ ₄" rakes Item Part No. Description ns K3-4-00/K LH/RH Electric Nev-R-Adjust 0 K3-0-00/K LH/RH Electric ns K3-0-00/K LH/RH Electric w/park ns K /K LH/RH Hydraulic Uni-servo ns K /K LH/RH Hydraulic Uni-servo w/park ns K /K LH/RH Hydraulic Duo-servo ns K /K LH/RH Hydraulic Duo-servo w/park ns K /K LH/RH Hydraulic Free acking ns K /K LH/RH Hydraulic F Corrosion Resistant ns - not shown Note: Spindle is not available for resale. Hubs Item Part No. Description olt Circle Hubs and Drums ½" Stud on ½" Stud on ½" Stud on ½" Stud on ½" Stud on.0 Plain Hubs ½" Stud on ½" Stud on ½" Stud on ½" Stud on ½" Stud on.0 Studs & Wheel Nuts Item Part No. Description ½-0 Pressed Wheel Stud ½-0 0 Cone Nut

27 #10F 4 Hub Group lbs. capacity Exp4400_ A Grease Lube Parts Item Part No. Description Grease Seal for E-Z Lube L14 Inner earing Cone L111 Inner earing Cup L4410 Outer earing Cup L444 Outer earing Cone Spindle Nut Cotter Pin (not used with E-Z Lube ) Grease Cap A Grease Cap for E-Z Lube Rubber Plug for E-Z Lube Spindle Washer Special Jam Nut for E-Z Lube (after 00) Spindle Nut Retainer for E-Z Lube (after 00) Hubs Item Part No. Description olt Circle Hubs and Drums ½" Stud on 4.0 Studs & Wheel Nuts Item Part No. Description ½-0 Pressed Wheel Stud ½-0 0 Cone Nut 10" x ¹ ₄" rakes Item Part No. Description 0 K LH Electric 0 K RH Electric ns K LH Electric Nev-R-Adjust ns K RH Electric Nev-R-Adjust ns - not shown Note: Spindle is not available for resale.

28 Nev-R-Lube Hub Group Service Parts Only Exp300nvr_ lbs. capacity Nev-R-Lube Parts 3MM Item Part No. Description Spindle Washer Spindle Nut Washer, Torque Label Snap Ring * Grease Cap 10" x ¹ ₄" rakes Item Part No. Description ns K3-4-00/K LH/RH Electric Nev-R-Adjust 0 K3-0-00/K LH/RH Electric ns K3-0-00/K LH/RH Electric w/park ns K /K LH/RH Hydraulic Uni-servo ns K /K LH/RH Hydraulic Uni-servo w/park ns K /K LH/RH Hydraulic Duo-servo ns K /K LH/RH Hydraulic Duo-servo w/park ns K /K LH/RH Hydraulic Free acking ns K /K LH/RH Hydraulic F Corrosion Resistant ns - not shown Note: Spindle is not available for resale. Hubs With earing & Wheel Studs Item Part No. Description olt Circle * Hub and Drum includes: on ¹ ₂-0 Press-in Stud * 3mm Cartridge earing * earing Retainer Wheel Nuts Item Part No. Description ½-0 0 Cone Nut * Available for service parts only.

29 D30, #10L 10" x 1¹ ₂" Electric rake lbs. capacity XE_ CSA approved at 3000#/1. SLR 3 Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate Assembly LH Actuating Lever Arm RH Actuating Lever Arm Washer Wire Clip Retractor Spring K Shoe & Lining Kit Contains: # Shoe Hold Down Cup 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Spring # Shoe Hold Down Pin *T* Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (green wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet rake Mounting olt - Press-in * rake Mounting Nut * Not included with complete brake assembly. Item sold separately.

30 D30, #10L 10" x 1¹ ₂" Nev-R-Adjust Electric rake xE_D44_Nev-R-Adj_-11 CSA approved at 3000#/1. SLR lbs. capacity Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate Assembly LH Actuating Lever Arm RH Actuating Lever Arm Washer Wire Clip Retractor Spring K LH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin T # Shoe Hold Down Spring K RH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin T # Shoe Hold Down Spring & Cup K LH & RH rake Adjuster Kit Contains: # Adjusting Screw Spring 1 # LH Lever Spring 1 # RH Lever Spring 1 # LH Adjuster Assembly 1 # RH Adjuster Assembly # Hook for Cable 1 # LH Adjusting Lever 1 # RH Adjusting Lever # Adjuster Cable 1 # LH Cable Lever 1 #01--0 RH Cable Lever # Adjuster Cable K Magnet Kit Contains: 1 # Magnet (green wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet rake Mounting olt - Press-in * rake Mounting Nut * Not included with complete brake assembly. Item sold separately.

31 D3, #10 10" x ¹ ₄" Electric rake lbs. capacity XE_ CSA approved at 300#/13.3 SLR 3 Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate Assembly LH Actuating Lever Arm RH Actuating Lever Arm Washer Wire Clip Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (green wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet rake Mounting olt - Press-in * rake Mounting Nut * Not included with complete brake assembly. Item sold separately. 30

32 D3, #10 10" x ¹ ₄" Electric rake With Parking Feature XEPF_ CSA approved at 300#/13.3 SLR lbs. capacity Electric Parking rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly LH Actuating Lever Arm RH Actuating Lever Arm Wire Clip K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (green wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet rake Mounting olt - Press-in * rake Mounting Nut LH acking Plate Assembly (includes items #1, -) RH acking Plate Assembly (includes items #1, -) LH Pivot Pin & Cam Sub-Assembly LH Pivot Pin & Cam Sub-Assembly LH Actuating Cam RH Actuating Cam Anchor Post & ushing Assembly Anchor Post Locknut Washer Pivot Pin Locknut Actuating Lever Retractor Spring * Not included with complete brake assembly. Item sold separately. 31

33 lbs. capacity D3, #10 10" x ¹ ₄" Nev-R-Adjust Electric rake CSA approved at 300#/13.3 SLR 10 10XE_Nev-R-Adj_ Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate Assembly LH Actuating Lever Arm RH Actuating Lever Arm Washer Wire Clip Retractor Spring K LH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K RH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K LH & RH rake Adjuster Kit Contains: # Adjusting Screw Spring 1 # LH Lever Spring 1 # RH Lever Spring 1 # LH Adjuster Assembly 1 # RH Adjuster Assembly # Hook for Cable 1 # LH Adjusting Lever 1 # RH Adjusting Lever # Adjuster Cable 1 # LH Cable Lever 1 #01--0 RH Cable Lever # Adjuster Cable K Magnet Kit Contains: 1 # Magnet (green wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet rake Mounting olt - Press-in * rake Mounting Nut * Not included with complete brake assembly. Item sold separately.

34 #10F 10" x ¹ ₄" Electric rake Manual Adjust XE_ lbs. capacity Note: rake mounting is not the same as a standard #10. It will not fit on a #10. Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate Assembly LH Actuating Lever Arm RH Actuating Lever Arm Washer Wire Clip Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (black wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet rake Mounting olt - Press-in * rake Mounting Nut * Not included with complete brake assembly. Item sold separately. 33

35 lbs. capacity #10F 10" x ¹ ₄" Nev-R-Adjust Electric rake xE_D44_Nev-R-Adj_-11 CSA approved at 4000#/13.0 SLR Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate Assembly LH Actuating Lever Arm RH Actuating Lever Arm Washer Wire Clip Retractor Spring K LH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K RH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K LH & RH rake Adjuster Kit Contains: # Adjusting Screw Spring 1 # LH Lever Spring 1 # RH Lever Spring 1 # LH Adjuster Assembly 1 # RH Adjuster Assembly # Hook for Cable 1 # LH Adjusting Lever 1 # RH Adjusting Lever # Adjuster Cable 1 # LH Cable Lever 1 #01--0 RH Cable Lever # Adjuster Cable K Magnet Kit Contains: 1 # Magnet (black wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet rake Mounting olt - Press-in * rake Mounting Nut * Not included with complete brake assembly. Item sold separately. This brake will not fit axles produced prior to /1/0.

36 D3, #10 10" x ¹ ₄" Hydraulic rake XH_1-0 Uni-Servo CSA approved at 300#/14.0 SLR; Uni-Servo lbs. capacity Note: Uni-Servo brakes to be used with surge actuator Hydraulic rake 0 K LH Complete rake Assembly-DS 0 K RH Complete rake Assembly-DS 0 K LH Complete rake Assembly-US 0 K RH Complete rake Assembly-US (shown) acking Plate Assembly (includes item #11) LH rake Cylinder Duo-Servo RH rake Cylinder Duo-Servo LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo or Cylinder Push Rod US (1) DS () Sems (screw & washer assembly) Anchor Post Washer Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Spring & Cup # Shoe Hold Down Pin # Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug rake Mounting olt - Press-in * rake Mounting Nut ns leeder Screw (included with item #) ns - not shown * Not included with complete brake assembly. Item sold separately. 3

37 D3, #10 10" x ¹ ₄" Hydraulic rake With Parking Feature lbs. capacity XHPF_ Uni-Servo Note: Uni-Servo brakes to be used with surge actuator CSA approved at 300#/14.0 SLR; Uni-Servo 1 1 Hydraulic Parking rake 0 K LH Complete rake Assembly-w/park-US 0 K RH Complete rake Assembly-w/park-US (shown) 0 K LH Complete rake Assembly-w/park-DS 0 K RH Complete rake Assembly-w/park-DS (shown) acking Plate Assembly (includes item #11) LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo LH rake Cylinder Duo-Servo RH rake Cylinder Duo-Servo or Cylinder Push Rod US (1) DS () Sems (screw & washer assembly) Anchor Post Washer Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Spring & Cup # Shoe Hold Down Pin # Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug rake Mounting olt - Press-in * rake Mounting Nut LH Parking Lever & Pin Assembly RH Parking Lever & Pin Assembly Parking Strut Parking Strut Spring Spring Tension Washer Retainer ns leeder Screw (included with item #) *ns Park rake Cable ns - not shown * Not included with complete brake assembly. Item sold separately. 3

38 D3, #10 10" x ¹ ₄" Hydraulic rake Free acking XHF_ CSA approved at 300#/14.0 SLR; Uni-Servo 13 1 A lbs. capacity Note: Uni-Servo brakes to be used with surge actuator Hydraulic Free acking rake 0 K LH Complete rake Assembly-F 0 K RH Complete rake Assembly-F (shown) acking Plate Assembly (includes item #11) LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo Cylinder Push Rod Sems (screw & washer assembly) Travel Link Retractor Spring A Shoe Lever Return Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Spring & Cup # Shoe Hold Down Pin # Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug rake Mounting olt - Press-in * rake Mounting Nut Shoe Lever Washer Primary Shoe Return ns leeder Screw (included with item #) *ns Park rake Cable ns - not shown * Not included with complete brake assembly. Item sold separately. Hydraulic Free acking rake Corrosion Resistant 0 K LH Complete rake Assembly-F 0 K RH Complete rake Assembly-F acking Plate Assembly (includes item #11) LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo Cylinder Push Rod Sems (screw & washer assembly) Travel Link Retractor Spring A Shoe Lever Return Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Spring & Cup # Shoe Hold Down Pin # Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug rake Mounting olt - Press-in * rake Mounting Nut Shoe Lever Washer Primary Shoe Return Spring ns leeder Screw (included with item #) 3

39 D3, #10 Disc rake for 3,00 Lb. Axles lbs. capacity 4 EXP300_Disc_ Disc rake 300# Anchor Yoke Assembly (includes item #) rake Mounting olt - Press-in 3 K Caliper Assembly Kit (includes items #, ) Caliper Mounting olt K rake Pad Kit (axle set) K Rotor Kit Yoke Mounting Nut ns leed Screw & Adapter (service part only) Disc rake Hubs & Studs ¹ ₂" Stud on ¹ ₂-0 x.0" Wheel Stud ns leeder Screw (included with items #3, 4) ns - not shown 3

40 Recommended Wheel Clearance for 3,00 Lb. Disc rake Dia. 1.4 Dia. Hubface Wheel Mounting Surface Dia lbs. capacity CAUTION: The above hub/rotor profile shows the minimum clearance needed to insure that no part of the wheel makes contact with any brake component. Make sure the wheel is in full contact with the hub face and does not drag against the brake caliper. If there is not full contact with the hub face, you may experience a dangerous wheel separation. 3

41 General Applications lbs. capacity 40 Axle Types Lbs. Capacity Complete service manual Precision machined steel spindles and integral cast iron hub/drums Press-in wheel studs 10" x ¼" CSA approved electric brakes 1" x " CSA approved electric brakes 1" x " hydraulic brakes Electric and hydraulic brakes are available with and without parking feature Hydraulic free backing brakes are available Inner wiring system for easier installation and protection of brake wiring Standard grease lubrication; E-Z Lube or Nev-R-Lube option 11 Totally rubber-cushioned for smooth, quiet, independent ride Easy installation with less maintenance Less transfer of road shock which insulates cargo from road shocks and vibration Rubber cords compounded for maximum dependability and durability Load-carrying cross member Self-damping action Independent wheel suspension system year limited warranty on suspension system Low profile for maximum road clearance Various starting angles to control trailer height High and low profile brackets with optional mounting brackets available Rubber cushioning eliminates metal-to-metal contact Shock absorption provided by the natural hysteresis of rubber Single or tandem axle assemblies Durable, wear-resistant components CAUTION: Triple axle assemblies are NOT recommended for #11 Torflex axles. D44, D & D0 leaf spring High strength 3" diameter tube Straight or Drop spindles (4" drop only) High quality alloy steel springs in a variety of capacities Single, tandem, or triple axle assemblies with equalized suspensions Slipper spring or double eye leaf spring suspension Optional hanger and attaching parts kits available Durable, wear-resistant components year limited warranty

42 Torflex Application Information 11 Start Angle 4 Down 3 Down. Down 10 Down Articulation Dimensions Dimensions are for top mount only. Side mount is." higher. Allow 3" bump clearance from full load. racket Profile Forward No Load Full Load Shock Load H L H L H L Low High Low High Low High Low High Left Hand Assembly Shown DEXTER Arm Length Axle Location L H Top of racket Center of Spindle #11 Overhang Per Side Spindle Min. Disc.* Max. Short.00".0" 10." Standard.0".0" 10." * Minimum overhang with disc brakes Start Angle lbs. capacity 0 Low High Up Low High Up Low High Note: Positive numbers in the H column indicate the spindle is ELOW the top of the bracket. Conversely, negative numbers are AOVE the top of the bracket. 11 Full Load Dimensions Dimensions are for low profile, top mount only. High profile brackets are." higher. Side mount is." higher. Allow 3" bump clearance from full load. C Top of racket H E D C Top of racket H E D C Top of racket H E D 10 Dn, 0 10 Up,. Up. Dn, 4 DN Start Angle * * * 4 Down. Down 10 Down 0 10 Up. Up Tire D E H C H C H C H C H C H C ST/R LT3/R LT/R R1.LT Columns D and E are dimensional examples only: * D Static Loaded Radius ** E Inflated Radius 41

43 Torflex Application Information lbs. capacity 11 racket Dimensions Forward For Wiring Access olt Size J A G Right Hand Side of Axle Shown C A D Low Profile E 1/ G F Side Mount Hanger #11 racket Dimensions Low High A C.0.0 D E F G.0.0 J N P Q olt Size ⁵ ₈" bolt Tube Size P E F High Profile N Q 4

44 Leaf Spring Application Information Double Eye Springs For Standard 33" Axle Spacing Single A/P-1-00 Tandem A/P Triple A/P Spring Length 1" 4" " A C D E For Optional 3" Axle Spacing Tandem A/P-4-00 Triple A/P Spring Length 1" 4" " C D E D44 Overhang Per Side Min. Max. Straight.00".0" D Overhang Per Side Min. Disc.* Max. Straight.3".00".0" 4" Drop." N/A.0" Nev-R-Lube.1".00".0" * Minimum overhang with disc brakes D0 Overhang Per Side Min. Disc.* Max. Straight.3".00" 10.00" 4" Drop." N/A 10.00" Nev-R-Lube.1".00" 10.00" * Minimum overhang with disc brakes Forward Z Y H Z Y SLR D A H lbs. capacity SLR D C E Z Y SLR H D C C Double Eye Axle Assemblies Hanger Kits Quantity Per Kit Part No. Description Height HGR HGR HGR-4-00 HGR-4-00 HGR Hanger 3." Front Hanger 1.44" Front Hanger.0" Center Hanger 3." Rear Hanger.1" Attaching Parts Kits Part No. Description A/P-1-00 A/P A/P-4-00 A/P A/P Flange Locknut Shackle olt Equalizer Equalizer Equalizer Equalizer Shackle Link Shackle Link, Long Shackle Link Assembly Shackle Link Assembly, Long For 3" axle spacing using " springs 43

45 Leaf Spring Application Information lbs. capacity Z Y Z Y Z Y SLR SLR SLR D D A H H H C Forward E Slipper Springs Single Tandem Triple A/P A/P-0-00 A/P-1-00 A/P A/P A C D E Note: All " wide slipper springs For 33." axle spacing For 3" axle spacing A,, E Hanger Spacing C Axle Spacing D Axle Location H Center of Spindle Y Frame Height Z Top of Tire to ottom of Frame SLR Static Load Radius To determine these values, contact your local sales engineer or distributor to run ProSpec. D C E Slipper Spring Axle Assemblies Hanger Kits Quantity Per Kit Part No. Description Height HGR HGR-0-00 HGR Front Hanger 4." Center Hanger 3.0" Rear Hanger 4.00" Attaching Parts Kits Part No. Description A/P A/P-0-00 A/P-1-00 A/P A/P ⁹ ₁₆-1 Locknut Keeper Nut Equalizer Nut Equalizer olt Keeper olt Spring Eye olt Equalizer Equalizer For 33." axle spacing For 3" axle spacing Some combinations of hangers and spring mountings may result in insufficient bump clearance. Refer to the Miscellaneous section for additional hanger kits, A/P kits, or other tires. 44

46 D44 Hub Group Exp4400_ A lbs. capacity Grease Lube Parts Item Part No. Description Grease Seal for E-Z Lube L14 Inner earing Cone L111 Inner earing Cup LM010 Outer earing Cup LM04 Outer earing Cone Spindle Nut Cotter Pin (not used with E-Z Lube ) Grease Cap A Grease Cap for E-Z Lube Rubber Plug for E-Z Lube Spindle Washer Special Jam Nut for E-Z Lube (after 00) Spindle Nut Retainer for E-Z Lube (after 00) Hubs Item Part No. Description olt Circle Hubs and Drums ½" Stud on.0 Studs & Wheel Nuts Item Part No. Description ½-0 Pressed Wheel Stud ½-0 0 Cone Nut Item Part No. Description ns K LH Electric ns K RH Electric 10" x ¹ ₄" rakes Old Style efore /1/0 10" x ¹ ₄" rakes New Style After /1/0 Item Part No. Description 0 K LH Electric 0 K RH Electric ns - not shown Note: Spindle is not available for resale. 4

47 D, D0 Hub Group lbs. capacity Exp00_ A Grease Lube Parts Item Part No. Description Grease Seal, E-Z Lube Seal Oil Seal Inner earing cone Inner earing Cup LM010 Outer earing Cup (for 00#) LM04 Outer earing Cone (for 00#) Outer earing Cup (for 000#) Outer earing Cone (for 000#) Spindle Nut Cotter Pin (not used with E-Z Lube ) Grease Cap A Grease Cap for E-Z Lube Rubber Plug for E-Z Lube Spindle Washer Special Jam Nut for E-Z Lube (after 00) Spindle Nut Retainer for E-Z Lube (after 00) Hubs Item Part No. Description olt Circle Hubs and Drums ½" Stud for 00# on ½" Stud 113 bearing for 000# on.0 Plain Hubs ½" Stud for 00# on ½" Stud 113 bearing for 000# on.0 Studs & Wheel Nuts Item Part No. Description ½-0 x 1. Long Press-in Stud* ½-0 x.0 Long Press-in Stud* (hub-drum after /0) ½-0 0 Cone Nut * Stud length measured under head to end of stud. on. hubs are available on these axles. See section in lbs. capacity. 4 1" x " rakes Item Part No. Description 0 K /K LH/RH Electric ns K /K LH/RH Electric w/park ns K3-3-00/K LH/RH Electric K CSA ns K3-3-00/K LH/RH Electric K CSA w/park ns K /K LH/RH Hydraulic Uni-servo ns K /K LH/RH Hydraulic Uni-servo w/park ns K3-3-00/K LH/RH Hydraulic Duo-servo ns K /K LH/RH Hydraulic Duo-servo w/park ns K /K LH/RH Hydraulic Free acking ns K /K LH/RH Hydraulic Free acking w/park ns K /K LH/RH Hydraulic F Corrosion Resistant ns K /K LH/RH Hydraulic F Corrosion Resistant w/park ns K3-4-00/K LH/RH Electric Nev-R-Adjust ns K3-4-00/K LH/RH Electric K CSA Nev-R-Adjust ns - not shown Note: Spindle is not available for resale.

48 D, D0 Nev-R-Lube Hub Group Exp00nvr_ lbs. capacity Nev-R-Lube Parts 4MM & 0MM Item Part No. Description Spindle Washer, 4mm Spindle Nut Washer, Torque Label Snap Ring Hub Cap, 4mm 1" x " rakes Item Part No. Description 0 K /K LH/RH Electric, K ns K /K LH/RH Electric w/park, K ns K /K LH/RH Hydraulic Uni-servo,.K ns K /K LH/RH Hydraulic Uni-servo w/park,.k ns K3-3-00/K LH/RH Hydraulic Duo-servo,.K ns K /K LH/RH Hydraulic Duo-servo w/park,.k ns K /K LH/RH Hydraulic Uni-servo, K ns K /K LH/RH Hydraulic Uni-servo w/park, K ns K /K LH/RH Hydraulic Duo-servo, K ns K /K LH/RH Hydraulic Duo-servo w/park, K ns K /K LH/RH Hydraulic Free acking, K ns K /K LH/RH Hydraulic Free acking w/park, K ns K3-4-00/K LH/RH Electric Nev-R-Adjust ns K3-4-00/K LH/RH Electric K CSA Nev-R-Adjust ns - not shown Note: Spindle is not available for resale. Hubs With earing and Wheel Studs Item Part No. Description olt Circle Hub and Drum includes: ¹ ₂-0 Press-in Studs mm earing Cartridge earing Retainer on.0 Wheel Nuts Item Part No. Description ½-0 0 Cone Nut on. hubs are available on these axles. See section in lbs. capacity. 4

49 SAVE TIME, SAVE MONEY WITH NEV-R-LUE Nev-R-Lube Features No more inner and outer bearings to repack Pre-lubricated and resistant to contamination Sealed for life, no bearing maintenance Increased durability and reliability No replacing seals when checking brakes Pre-set adjustment allows for easy installation Human error is virtually eliminated in bearing adjustment Five-year or 100,000 mile limited warranty What is Nev-R-Lube? Dexter s Nev-R-Lube bearings are comprised of opposed tapered roller bearing cones sealed inside of a precision ground, one piece double cup arrangement. These bearings are designed with a small amount of axial end play. The end play is essential to the longevity of the bearing s service life. Nev-R-Lube is not designed for immersion in water, such as boat trailer use. 4mm SEALED CARTRIDGE EARINGS D and D0 leaf spring axles #11 and #1 Torflex axles Straight spindles only Up to,000 lbs. capacity on.0" bolt circle hub-drums 1" x " brakes Use only zero offset wheels 0mm SEALED CARTRIDGE EARINGS D0, D, and D0 leaf spring axles #1, #1V, and #13 Torflex axles Straight spindles only Up to,000 lbs. capacity on.0" bolt circle hub-drums 1" x ", 1¹ ₄" x ¹ ₂", and 1¹ ₄" x 3³ ₈" brakes Can be used with zero to ¹ ₂" inset wheels at,000 lb. ratings Zero offset or 0.1" inset wheels only at,000 lbs. capacity Nev-R-Lube is subject to the maintenance and inspection procedures as outlined in the Dexter Operation Maintenance Service Manual. 4

50 D44 10" x ¹ ₄" Electric rake Manual Adjust XE_ CSA approved at 4400#/13.0 SLR lbs. capacity Electric rake Old Style efore /1/0 ns K LH Complete rake Assembly ns K RH Complete rake Assembly acking Plate Assembly LH Actuating Lever Arm RH Actuating Lever Arm Washer Wire Clip Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (black wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet rake Mounting olt - Press-in * rake Mounting Nut ns - not shown * Not included with complete brake assembly. Item sold separately. Electric rake New Style After /1/0 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate Assembly LH Actuating Lever Arm RH Actuating Lever Arm Washer Wire Clip Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (black wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet rake Mounting olt - Press-in * rake Mounting Nut * Not included with complete brake assembly. Item sold separately. 4

51 lbs. capacity D44 10" x ¹ ₄" Nev-R-Adjust Electric rake xE_D44_Nev-R-Adj_-11 CSA approved at 4400#/13.0 SLR Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly acking Plate Assembly LH Actuating Lever Arm RH Actuating Lever Arm Washer Wire Clip Retractor Spring K LH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K RH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K LH & RH rake Adjuster Kit Contains: # Adjusting Screw Spring 1 # LH Lever Spring 1 # RH Lever Spring 1 # LH Adjuster Assembly 1 # RH Adjuster Assembly # Hook for Cable 1 # LH Adjusting Lever 1 # RH Adjusting Lever # Adjuster Cable 1 # LH Cable Lever 1 #01--0 RH Cable Lever # Adjuster Cable K Magnet Kit Contains: 1 # Magnet (black wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet rake Mounting olt - Press-in * rake Mounting Nut * Not included with complete brake assembly. Item sold separately. This brake will not fit axles produced prior to /1/0.

52 D, D0 1" x " Electric rake X_K_ CSA approved at 00#/14. SLR CSA approved at 000#/14. SLR lbs. capacity Electric rake 000# (CSA 00#) 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) acking Plate Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet Anchor Post Washer * Nut Washer Assembly * Not included with complete brake assembly. Item sold separately. Electric rake 000# (CSA 000#) 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly acking Plate Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet Anchor Post Washer * Nut Washer Assembly 1

53 D, D0 1" x " Electric rake With Parking Feature lbs. capacity XEPF_ CSA approved at 00#/14. SLR CSA approved at 000#/14. SLR 3 Electric Parking rake 000# (CSA 00#) 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet * Nut Washer Assembly LH acking Plate Assembly Complete (includes #1-) RH acking Plate Assembly Complete (includes #1-) LH acking Plate Assembly RH acking Plate Assembly LH Pivot Pin & Cam Sub-Assembly RH Pivot Pin & Cam Sub-Assembly LH Actuating Cam RH Actuating Cam Anchor Post & ushing Sub-Assembly Anchor Post Locknut Washer Pivot Pin Locknut Parking rake Lever Retractor Spring * Not included with complete brake assembly. Item sold separately. Electric Parking rake 000# (CSA 000#) 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet * Nut Washer Assembly LH acking Plate Assembly Complete (includes #1-) RH acking Plate Assembly Complete (includes #1-) LH acking Plate Assembly RH acking Plate Assembly LH Pivot Pin & Cam Sub-Assembly RH Pivot Pin & Cam Sub-Assembly LH Actuating Cam RH Actuating Cam Anchor Post & ushing Sub-Assembly Anchor Post Locknut Washer Pivot Pin Locknut Parking rake Lever Retractor Spring

54 D, D0 1" x " Nev-R-Adjust Electric rake 1 1x_Nev-R-Adj_ CSA approved at 00#/14. SLR CSA approved at 000#/14. SLR lbs. capacity Electric rake 000# (CSA 00#) 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) acking Plate Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip Retractor Spring K LH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K RH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K LH & RH rake Adjuster Kit Contains: # Adjusting Screw Spring 1 # LH Lever Spring 1 # RH Lever Spring 1 # LH Adjuster Assembly 1 # RH Adjuster Assembly # Adjuster Cable # Hook for Cable 1 # LH Adjusting Lever 1 # RH Adjusting Lever K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet Anchor Post Washer * Nut Washer Assembly * Not included with complete brake assembly. Item sold separately. Electric rake 000# (CSA 000#) 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) acking Plate Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip Retractor Spring K LH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K RH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K LH & RH rake Adjuster Kit Contains: # Adjusting Screw Spring 1 # LH Lever Spring 1 # RH Lever Spring 1 # LH Adjuster Assembly 1 # RH Adjuster Assembly # Adjuster Cable # Hook for Cable 1 # LH Adjusting Lever 1 # RH Adjusting Lever K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet Anchor Post Washer * Nut Washer Assembly 3

55 D, D0 1" x " Hydraulic rake lbs. capacity XH_ Uni-Servo Note: Uni-Servo brakes to be used with surge actuator Hydraulic rake 00# 0 K LH Complete rake Assembly-DS 0 K RH Complete rake Assembly-DS (shown) 0 K LH Complete rake Assembly-US 0 K RH Complete rake Assembly-US (shown) acking Plate Assembly LH rake Cylinder Duo-Servo RH rake Cylinder Duo-Servo LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo or Cylinder Push Rod US (1) DS () Sems (screw & washer assembly) Anchor Post Washer Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Spring & Cup # Shoe Hold Down Pin # Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug * Nut Washer Assembly ns leeder Screw (included with item #) ns - not shown * Not included with complete brake assembly. Item sold separately. 4

56 D, D0 1" x " Hydraulic rake With Parking Feature 1 4 1XHPF_ Uni-Servo lbs. capacity Note: Uni-Servo brakes to be used with surge actuator Hydraulic Parking rake 00# 0 K LH Complete rake Assembly-DS 0 K RH Complete rake Assembly-DS (shown) 0 K LH Complete rake Assembly-US 0 K RH Complete rake Assembly-US (shown) LH acking Plate Assembly RH acking Plate Assembly LH rake Cylinder Duo-Servo RH rake Cylinder Duo-Servo LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo or Cylinder Push Rod US (1) DS () Sems (screw & washer assembly) Anchor Post Washer Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Spring & Cup # Shoe Hold Down Pin # Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug * Nut Washer Assembly LH Parking Lever and Pin RH parking Lever and Pin Parking Strut Parking Strut Spring Spring Tension Washer Retainer ns leeder Screw (included with item #) *ns Park rake Cable ns - not shown * Not included with complete brake assembly. Item sold separately.

57 D, D0 Disc rake for,000 Lb. Axles lbs. capacity 1 CSA approved at 000#/14.3 SLR 4 Exp000disc_ Disc rake 000# LH Anchor Yoke RH Anchor Yoke (shown) K Caliper Assembly Kit for LH or RH Contains: Caliper Mounting Nut Caliper Mounting olt Cotter Ring Tube Clamp Anti-Rattle Spring leeder Screw Adapter Fitting Pad Retaining Pin Cross Over Hydraulic Line (yokes without notch) Cross Over Hydraulic Line (yokes with notch) Hex olt Assembled Caliper Half 3 K rake Pad Kit (axle set) 4 K Rotor Kit ³ ₈" rake Mounting Nut-Washer Assembly Disc rake Hubs & Studs Grease ¹ ₂" Studs on ¹ ₂-0 x.0" Press-in Stud (hubs after /0) Disc rake 000# With 4MM Nev-R-Lube LH Anchor Yoke RH Anchor Yoke K Caliper Assembly Kit for LH or RH Contains: Caliper Mounting Nut Caliper Mounting olt Cotter Ring Tube Clamp Anti-Rattle Spring leeder Screw Adapter Fitting Pad Retaining Pin Cross Over Hydraulic Line (yokes without notch) Cross Over Hydraulic Line (yokes with notch) Hex olt Assembled Caliper Half 3 K rake Pad Kit (axle set) 4 K Rotor Kit ³ ₈" rake Mounting Nut-Washer Assembly Nev-R-Lube Disc rake Hubs ¹ ₂" Studs, 4mm on ¹ ₂-0 x.0" Press-in Stud (hubs after /0)

58 Recommended Wheel Clearance for,000 Lb. Disc rake Hubface Wheel Mounting Surface Dia Dia lbs. capacity CAUTION: The above hub/rotor profile shows the minimum clearance needed to insure that no part of the wheel makes contact with any brake component. Make sure the wheel is in full contact with the hub face and does not drag against the brake caliper. If there is not full contact with the hub face, you may experience a dangerous wheel separation.

59 lbs. capacity General Applications Axle Types Lbs. Capacity Complete service manual Precision machined, forged steel spindles Precision machined integral cast iron hub/drums -bolt and bolt (UTG) hubs available Standard grease; optional oil bath; E-Z Lube or Nev-R-Lube option Press-in wheel studs (-bolt) 1" x " electric brakes, CSA approved at 000 lbs, 1" x " hydraulic brakes rakes are available with and without parking feature Hydraulic free backing brakes available Hydraulic brakes - uni-servo and duo-servo available d0 & D0 leaf spring High quality alloy steel springs in a variety of capacities Single, tandem, or triple axle assemblies with equalized suspensions Slipper spring or double eye leaf spring suspension Optional hanger and attaching parts kits available Durable, wear-resistant components Inner wiring system for easier installation and protection of brake wiring Heavy wall 3" diameter tube Straight or Drop spindles (4" drop only) year limited warranty 1 1T Totally rubber-cushioned for smooth, quiet, independent ride Easy installation with less maintenance Less transfer of road shock which insulates cargo from road shocks and vibration Self-damping action Load-carrying cross member Rubber cords compounded for maximum dependability and durability Independent wheel suspension system year limited warranty on suspension system Low profile for maximum road clearance Various starting angles to control trailer height High and low profile brackets with optional mounting brackets are available Rubber cushioning eliminates metal-to-metal contact Shock absorption provided by the natural hysteresis of rubber Single or tandem axle assemblies Durable, wear-resistant components CAUTION: Triple axle assemblies are NOT recommended for #1 Torflex axles, however the #1T Torflex axle is designed for triple applications.

60 Torflex Application Information 1 Start Angle 4 Down 3 Down. Down 10 Down Articulation Dimensions Dimensions are for top mount only. Side mount is.31" higher. Allow 3" bump clearance from full load. racket Profile Forward No Load Full Load Shock Load H L H L H L Low High Low High Low High Low High Left Hand Assembly Shown DEXTER Arm Length Axle Location L #1 Overhang Per Side Spindle Min. Max. Short.00" 1.0" Standard.0" 1.0" H Top of racket Center of Spindle Start Angle lbs. capacity 0 Low High Up. Up Low High Low High Note: Positive numbers in the H column indicate the spindle is ELOW the top of the bracket. Conversely, negative numbers are AOVE the top of the bracket. 1 Full Load Dimensions Dimensions are for low profile, top mount only. High profile brackets are." higher. Side mount is.31" higher. Allow 3" bump clearance from full load. Top of racket C H E D Top of racket C H E D C Top of racket H E D 10 DN, 0 10 Up,. Up. Dn, 4 Dn Start Angle * * * 4 Down. Down 10 Down 0 10 Up. Up Tire D E H C H C H C H C H C H C LT3/R LT LT Columns D and E are dimensional examples only: * D Static Loaded Radius ** E Inflated Radius

61 Torflex Application Information lbs. capacity 1T Start Angle 4 Down 3 Down. Down 10 Down Articulation Dimensions Dimensions are for top mount only. Side mount is.31" higher. Allow 3" bump clearance from full load. racket Profile Forward No Load Full Load Shock Load H L H L H L Low High Low High Low High Low High Left Hand Assembly Shown DEXTER Arm Length Axle Location L #1T Overhang Per Side Spindle Min. Max. Short.00" 1.0" Standard.0" 1.0" H Top of racket Center of Spindle Start Angle 0 Low High Up. Up Low High Low High Note: Positive numbers in the H column indicate the spindle is ELOW the top of the bracket. Conversely, negative numbers are AOVE the top of the bracket. 1T Full Load Dimensions Dimensions are for low profile, top mount only. High profile brackets are." higher. Side mount is.31" higher. Allow 3" bump clearance from full load. Top of racket C H E D Top of racket C H E D C Top of racket H E D 10 DN, 0 10 Up,. Up. Dn, 4 Dn 0 Start Angle * * * 4 Down. Down 10 Down 0 10 Up. Up Tire D E H C H C H C H C H C H C 10R1.HC /R LT LT R 1.HC Columns D and E are dimensional examples only: * D Static Loaded Radius ** E Inflated Radius

62 Torflex Application Information 1 racket Dimensions Forward For Wiring Access olt Size J A G Right Hand Side of Axle Shown C A D E Low Profile F 1/ G lbs. capacity Side Mount Hanger #1 racket Dimensions Low High A C.0.0 D E F G.0.0 J.0.0 N P Q olt Size ⁵ ₈" bolt Tube Size P E F N High Profile Q 1

63 Torflex Application Information lbs. capacity 1T racket Dimensions Forward For Wiring Access olt Size J A G Right Hand Side of Axle Shown L C A D E Low Profile F 1/ G Side Mount Hanger #1T racket Dimensions Low High A C D E F G.0.0 J.. L.. P Q olt Size ⁵ ₈" bolt Tube Size P E F Q High Profile

64 Leaf Spring Application Information Double Eye Springs For Standard 33" Axle Spacing Single A/P-1-00 Tandem A/P Triple A/P Spring Length 1" 4" " A C D E For Optional 3" Axle Spacing Tandem A/P-4-00 Triple A/P Spring Length 1" 4" " C D E D0 Overhang Per Side Min. Disc* Max. Straight.3".00" 10.00" 4" Drop." N/A.0" Nev-R-Lube.1".00" 10.00" * Minimum overhang with disc brakes D0 Overhang Per Side Min. Max. Straight.3".00" 4" Drop.".00" Nev-R-Lube.3".00" Disc.00".00" Z Y SLR Forward H Z Y SLR D E H Z Y SLR C D A H lbs. capacity D C C Double Eye Axle Assemblies Hanger Kits Quantity Per Kit Part No. Description Height HGR HGR HGR-4-00 HGR-4-00 HGR Hanger 3." Front Hanger 1.44" Front Hanger.0" Center Hanger 3." Rear Hanger.1" Attaching Parts Kits Part No. Description A/P-1-00 A/P A/P-4-00 A/P A/P Flange Locknut Shackle olt Equalizer Equalizer Equalizer Equalizer Shackle Link Shackle Link, Long Shackle Link Assembly Shackle Link Assembly, Long For 3" axle spacing using " springs 3

65 Leaf Spring Application Information lbs. capacity Z Y Z Y Z Y SLR SLR SLR D D A H H H C Forward E Slipper Springs Single Tandem Triple A/P A/P-0-00 A/P-1-00 A/P A/P A C D E Note: All " wide slipper springs For 33." axle spacing For 3" axle spacing A,, E Hanger Spacing C Axle Spacing D Axle Location H Center of Spindle Y Frame Height Z Top of Tire to ottom of Frame SLR Static Load Radius To determine these values, contact your local sales engineer or distributor to run ProSpec. D C E Slipper Spring Axle Assemblies Hanger Kits Quantity Per Kit Part No. Description Height HGR HGR-0-00 HGR Front Hanger 4." Center Hanger 3.0" Rear Hanger 4.00" Attaching Parts Kits Part No. Description A/P A/P-0-00 A/P-1-00 A/P A/P ⁹ ₁₆-1 Locknut Keeper Nut Equalizer Nut Equalizer olt Keeper olt Spring Eye olt Equalizer Equalizer For 33." axle spacing For 3" axle spacing Some combinations of hangers and spring mountings may result in insufficient bump clearance. Refer to the Miscellaneous section for additional hanger kits, A/P kits, or other tires. 4

66 and Demountable Hub Group Exp000_ A A A Grease Lube Parts 3 1 Item Part No. Description E-Z Lube Seal." Inner earing Cone Inner earing Cup Outer earing Cup - Hub 4A Outer earing Cup - Demountable A Outer earing Cone - Hub A Outer earing Cone - Demountable Spindle Nut Cotter Pin (not used with E-Z Lube ) Grease Cap - Hub A Grease Cap - Demountable Grease Cap for E-Z Lube - Hub Grease Cap E-Z Lube Chrome Option - Hub C Grease Cap for E-Z Lube - Demountable C Grease Cap for E-Z Lube Chrome Option - Dem. D E-Z Lube Rubber Plug Spindle Washer ⁹ ₁₆-1 Nut for Rim Clamp Rim Clamp Special Jam Nut for E-Z Lube (after 00) Spindle Nut Retainer for E-Z Lube (after 00) Oil Lube Parts Item Part No. Description Oil Seal." Inner earing cone Inner earing Cup Outer earing Cup - Hub Outer earing Cup - Demountable Outer earing Cone A Outer earing Cone Spindle Nut Cotter Pin E Oil Cap - Hub ns Oil Cap - Demountable F Oil Cap Plug Spindle Washer Oil Filler Plug - and Demountable ns Oil Cap Plug ⁹ ₁₆-1 Nut for Rim Clamp Rim Clamp O Ring ns Demountable O Ring Note: Spindle is not available for resale. on. hubs are available on these axles. See section in lbs. capacity. C D E F D Hubs rakes 11 Item Part No. Description olt Circle Hubs/Drums Grease ⁹ ₁₆" Stud Demountable Oil ⁹ ₁₆" Stud Demountable Grease ¹ ₂" Stud on Grease ⁹ ₁₆" Stud on Grease ⁵ ₈" Stud on Oil ¹ ₂" Stud on Oil ⁹ ₁₆" Stud on Oil ⁵ ₈" Stud on.0 Plain Hubs Grease ¹ ₂" Stud on Grease ⁹ ₁₆" Stud on Grease ⁵ ₈" Stud on Oil ¹ ₂" Stud on.0 Item Part No. Description 0 K /K LH/RH Electric K ns K /K LH/RH Electric w/park ns K3-3-00/K LH/RH Electric K CSA ns K3-3-00/K LH/RH Electric K CSA w/park ns K /K LH/RH Electric K ns K /K LH/RH Hydraulic Uni-servo K ns K /K LH/RH Hydraulic Uni-servo K w/park ns K /K LH/RH Hydraulic Duo-servo K ns K /K LH/RH Hydraulic Duo-servo K w/park ns K /K LH/RH Hydraulic Uni-servo K F ns K /K LH/RH Hydraulic Uni-servo K F w/park ns K /K LH/RH Hydraulic Uni-servo K F ns K /K LH/RH Hydraulic Uni-servo K F w/park ns K3-4-00/K LH/RH Electric Nev-R-Adjust ns K3-4-00/K LH/RH Electric K CSA Nev-R-Adjust Studs & Wheel Nuts Item Part No. Description ⁹ ₁₆-1 Stud - UTG ½-0 x 1.4 Long Press-in Stud* (hubs before 1/04) ½-0 x.0 Long Press-in Stud* (hubs after 1/04) ½-0 0 Cone Nut ns ⁹ ₁₆-1 Press-in Stud ns ⁹ ₁₆-1 0 Cone Nut ns ⁵ ₈-1 Press-in Stud ns ⁵ ₈-1 0 Cone Nut ns - not shown * Stud length measured under head to end of stud lbs. capacity

67 and Nev-R-Lube Hub Group lbs. capacity Exp000nvr_ Nev-R-Lube Parts Item Part No. Description ns Spindle Washer, 4mm Spindle Washer, 0mm Spindle Nut Washer, Torque Label Snap Ring ns Grease Cap, 4mm Grease Cap, 0mm 1" x " rakes Item Part No. Description 0 K /K LH/RH Electric ns K /K LH/RH Electric K ns K /K LH/RH Hydraulic Uni-servo, K ns K /K LH/RH Hydraulic Uni-servo w/park, K ns K /K LH/RH Hydraulic Duo-servo, K ns K /K LH/RH Hydraulic Duo-servo w/park, K ns K /K LH/RH Hydraulic Free acking, K ns K /K LH/RH Hydraulic K F w/park ns K3-3-00/K LH/RH Electric K CSA ns K3-4-00/K LH/RH Electric Nev-R-Adjust ns K3-4-00/K LH/RH Electric K CSA Nev-R-Adjust ns - not shown Note: Spindle is not available for resale. Hubs With earing and Wheel Studs Item Part No. Description olt Circle ns Hub and Drum includes: on ¹ ₂-0 Press-in Studs mm earing Cartridge earing Retainer Hub and Drum includes: on ¹ ₂-0 Press-in Studs mm earing Cartridge earing Retainer ns Hub and Drum includes: on ⁹ ₁₆-1 Press-in Studs mm earing Cartridge earing Retainer ns Hub and Drum includes: ⁵ ₈-1 Press-in Studs mm earing Cartridge earing Retainer on.0 Wheel Nuts Item Part No. Description ½-0 0 Cone Nut ns ⁹ ₁₆-1 0 Cone Nut ns ⁵ ₈-1 0 Cone Nut

68 1" x " Electric rake X_K_ CSA approved at 000#/14. SLR lbs. capacity Electric rake 000# (CSA 00#) 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) acking Plate Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet Anchor Post Washer * Nut Washer Assembly * Not included with complete brake assembly. Item sold separately. Electric rake 000# (CSA 000#) 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly acking Plate Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet Anchor Post Washer * Nut Washer Assembly These brakes are rated to a maximum capacity of 000 lbs. / pair

69 1" x " Electric rake With Parking Feature lbs. capacity XEPF_ CSA approved at 000#/14. SLR 3 Electric Parking rake 000# (CSA 00#) 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet * Nut Washer Assembly LH acking Plate Assembly Complete (includes #1-) RH acking Plate Assembly Complete (includes #1-) LH acking Plate Assembly RH acking Plate Assembly LH Pivot Pin & Cam Sub-Assembly RH Pivot Pin & Cam Sub-Assembly LH Actuating Cam RH Actuating Cam Anchor Post & ushing Sub-Assembly Anchor Post Locknut Washer Pivot Pin Locknut Parking rake Lever Retractor Spring * Not included with complete brake assembly. Item sold separately. Electric Parking rake 000# (CSA 000#) 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet * Nut Washer Assembly LH acking Plate Assembly Complete (includes #1-) RH acking Plate Assembly Complete (includes #1-) LH acking Plate Assembly RH acking Plate Assembly LH Pivot Pin & Cam Sub-Assembly RH Pivot Pin & Cam Sub-Assembly LH Actuating Cam RH Actuating Cam Anchor Post & ushing Sub-Assembly Anchor Post Locknut Washer Pivot Pin Locknut Parking rake Lever Retractor Spring These brakes are rated to a maximum capacity of 000 lbs. / pair

70 1" x " Nev-R-Adjust Electric rake 1 1x_Nev-R-Adj_ CSA approved at 000#/14. SLR lbs. capacity Electric rake 000# 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) acking Plate Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip Retractor Spring K LH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K RH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K LH & RH rake Adjuster Kit Contains: # Adjusting Screw Spring 1 # LH Lever Spring 1 # RH Lever Spring 1 # LH Adjuster Assembly 1 # RH Adjuster Assembly # Adjuster Cable # Hook for Cable 1 # LH Adjusting Lever 1 # RH Adjusting Lever K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet Anchor Post Washer * Nut Washer Assembly * Not included with complete brake assembly. Item sold separately. Electric rake 000# (CSA 000#) 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) acking Plate Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip Retractor Spring K LH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K RH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K LH & RH rake Adjuster Kit Contains: # Adjusting Screw Spring 1 # LH Lever Spring 1 # RH Lever Spring 1 # LH Adjuster Assembly 1 # RH Adjuster Assembly # Adjuster Cable # Hook for Cable 1 # LH Adjusting Lever 1 # RH Adjusting Lever K Magnet Kit Contains: 1 # Magnet (white wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet Anchor Post Washer * Nut Washer Assembly

71 1" x " K Electric rake lbs. capacity X_K_ CSA approved at 000#/13. SLR 11 4 Electric rake 000# 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) acking Plate Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip Retractor Spring K Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup Adjuster Assembly Adjusting Screw Spring K Magnet Kit Contains: 1 # Magnet (black wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet Anchor Post Washer * Nut Washer Assembly * Not included with complete brake assembly. Item sold separately. 0

72 1" x " K Nev-R-Adjust Electric rake 1 1x_Nev-R-Adj_oval mag_ CSA approved at 000#/13. SLR lbs. capacity Electric rake 000# 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) acking Plate Assembly LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip Retractor Spring K LH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K RH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Pin # # Shoe Hold Down Spring & Cup K LH & RH rake Adjuster Kit Contains: # Adjusting Screw Spring 1 # LH Lever Spring 1 # RH Lever Spring 1 # LH Adjuster Assembly 1 # RH Adjuster Assembly # Adjuster Cable # Hook for Cable 1 # LH Adjusting Lever 1 # RH Adjusting Lever K Magnet Kit Contains: 1 # Magnet (black wire) 1 # Magnet Clip 1 # Magnet Spring Adjuster Slot Plug Wire Grommet Anchor Post Washer * Nut Washer Assembly * Not included with complete brake assembly. Item sold separately. 1

73 1" x " Hydraulic rake lbs. capacity XH_ Uni-Servo Note: Uni-Servo brakes to be used with surge actuator Hydraulic rake 000# 0 K LH Complete rake Assembly-US 0 K RH Complete rake Assembly-US (shown) 0 K LH Complete rake Assembly-DS 0 K RH Complete rake Assembly-DS (shown) acking Plate Assembly LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo LH rake Cylinder Duo-Servo RH rake Cylinder Duo-Servo or Cylinder Push Rod US (1) DS () Sems (screw & washer assembly) Anchor Post Washer Retractor Spring K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining # Shoe Hold Down Spring & Cup # Shoe Hold Down Pin #4 K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining # Shoe Hold Down Spring & Cup # Shoe Hold Down Pin # Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug * Nut Washer Assembly ns leeder Screw (included with item #) ns - not shown * Not included with complete brake assembly. Item sold separately.

74 1" x " Hydraulic rake With Parking Feature 1 4 1XHPF_ Uni-Servo lbs. capacity Note: Uni-Servo brakes to be used with surge actuator Hydraulic Parking rake 000# 0 K LH Complete rake Assembly-DS 0 K RH Complete rake Assembly-DS (shown) 0 K LH Complete rake Assembly-US 0 K RH Complete rake Assembly-US (shown) LH acking Plate Assembly RH acking Plate Assembly LH rake Cylinder Duo-Servo RH rake Cylinder Duo-Servo LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo or Cylinder Push Rod US (1) DS () Sems (screw & washer assembly) Anchor Post Washer Retractor Spring K LH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Spring & Cup # Shoe Hold Down Pin #4 K RH Shoe & Lining Kit Contains: 1 # Primary Shoe & Lining 1 # Secondary Shoe & Lining # Shoe Hold Down Spring & Cup # Shoe Hold Down Pin # Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug * Nut Washer Assembly LH Parking Lever and Pin RH parking Lever and Pin Parking Strut Parking Strut Spring Spring Tension Washer Retainer ns leeder Screw (included with item #) *ns Park rake Cable ns - not shown * Not included with complete brake assembly. Item sold separately. 3

75 1" x " Hydraulic rake Free acking lbs. capacity XHF_ A Note: Uni-Servo brakes to be used with surge actuator 4 Hydraulic Free acking rake 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) acking Plate Assembly LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo Cylinder Push Rod Sems (screw & washer assembly) Travel Link Retractor Spring A Shoe Lever Return Spring K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining 1 # Shoe Hold Down Spring & Cup-Sec. # Shoe Hold Down Cup-Primary 1 # Shoe Hold Down Spring-Primary 1 # Shoe Hold Down Pin #1-Primary 1 # Shoe Hold Down Pin #-Sec. K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining 1 # Shoe Hold Down Spring & Cup-Sec. # Shoe Hold Down Cup-Primary 1 # Shoe Hold Down Spring-Primary 1 # Shoe Hold Down Pin #1-Primary 1 # Shoe Hold Down Pin #-Sec Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug * Nut Washer Assembly Shoe Lever Locknut Screw Washer Primary Shoe Return Spring ns leeder Screw (included with item #) ns - not shown * Not included with complete brake assembly. Item sold separately. Hydraulic Free acking rake Corrosion Resistant 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly acking Plate Assembly LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo Cylinder Push Rod Sems (screw & washer assembly) Travel Link Retractor Spring A Shoe Lever Return Spring K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining 1 # Shoe Hold Down Spring & Cup-Sec. # Shoe Hold Down Cup-Primary 1 # Shoe Hold Down Spring & Cup-Prim. 1 # Shoe Hold Down Pin #1-Primary 1 # Shoe Hold Down Pin #-Sec. K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining 1 # Shoe Hold Down Spring & Cup-Sec. # Shoe Hold Down Cup-Primary 1 # Shoe Hold Down Spring & Cup-Prim. 1 # Shoe Hold Down Pin #1-Primary 1 # Shoe Hold Down Pin #-Sec Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug * Nut Washer Assembly Shoe Lever Locknut Screw Washer Primary Shoe Return Spring ns leeder Screw (included with item #)

76 1" x " Hydraulic rake Free acking With Parking Feature 4 1XHFP_ Note: Uni-Servo brakes to be used with surge actuator A lbs. capacity Hydraulic Free acking Parking rake 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly (shown) LH acking Plate Assembly RH acking Plate Assembly LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo Cylinder Push Rod Sems (screw & washer assembly) Travel Link Retractor Spring A Shoe Lever Return Spring K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining 1 # Shoe Hold Down Spring & Cup-Sec. # Shoe Hold Down Cup-Primary 1 # Shoe Hold Down Spring-Primary 1 # Shoe Hold Down Pin #1-Primary 1 # Shoe Hold Down Pin #-Sec. K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining 1 # Shoe Hold Down Spring & Cup-Sec. # Shoe Hold Down Cup-Primary 1 # Shoe Hold Down Spring-Primary 1 # Shoe Hold Down Pin #1-Primary 1 # Shoe Hold Down Pin #-Sec Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug * Nut Washer Assembly Shoe Lever Locknut Screw Washer Primary Shoe Return Spring Retainer LH Parking Lever and Pin RH Parking Lever and Pin Strut for Parking rake Washer ns leeder Screw (included with item #) *ns Park rake Cable ns - not shown * Not included with complete brake assembly. Item sold separately. Hydraulic Free acking Parking rake Corrosion Resistant 0 K LH Complete rake Assembly 0 K RH Complete rake Assembly LH acking Plate Assembly RH acking Plate Assembly LH rake Cylinder Uni-Servo RH rake Cylinder Uni-Servo Cylinder Push Rod Sems (screw & washer assembly) Travel Link Retractor Spring A Shoe Lever Return Spring K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining 1 # Shoe Hold Down Spring & Cup-Sec. # Shoe Hold Down Cup-Primary 1 # Shoe Hold Down Spring-Primary 1 # Shoe Hold Down Pin #1-Primary 1 # Shoe Hold Down Pin #-Sec. K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining 1 # Shoe Hold Down Spring & Cup-Sec. # Shoe Hold Down Cup-Primary 1 # Shoe Hold Down Spring-Primary 1 # Shoe Hold Down Pin #1-Primary 1 # Shoe Hold Down Pin #-Sec Adjuster Assembly Adjusting Screw Spring Adjuster Slot Plug * Nut Washer Assembly Shoe Lever Locknut Screw Washer Primary Shoe Return Spring Retainer LH Parking Lever and Pin RH Parking Lever and Pin Strut for Parking rake Washer ns leeder Screw (included with item #)

77 Disc rake for,000 Lb. Axles lbs. capacity 1 CSA approved at 000#/14.3 SLR 4 Exp000disc_ Disc rake 000# LH Anchor Yoke RH Anchor Yoke (shown) K Caliper Assembly Kit for LH or RH Contains: Caliper Mounting Nut Caliper Mounting olt Cotter Ring Tube Clamp Anti-Rattle Spring leeder Screw Adapter Fitting Pad Retaining Pin Cross Over Hydraulic Line (yokes without notch) Cross Over Hydraulic Line (yokes with notch) Hex olt Assembled Caliper Half 3 K rake Pad Kit (axle set) 4 K Rotor Kit ³ ₈" rake Mounting Nut-Washer Assembly Disc rake Hubs & Studs Grease ¹ ₂" Studs on ¹ ₂-0 x.0" Press-in Stud (hubs after /0) Disc rake 000# With 4MM Nev-R-Lube LH Anchor Yoke RH Anchor Yoke K Caliper Assembly Kit for LH or RH Contains: Caliper Mounting Nut Caliper Mounting olt Cotter Ring Tube Clamp Anti-Rattle Spring leeder Screw Adapter Fitting Pad Retaining Pin Cross Over Hydraulic Line (yokes without notch) Cross Over Hydraulic Line (yokes with notch) Hex olt Assembled Caliper Half 3 K rake Pad Kit (axle set) 4 K Rotor Kit ³ ₈" rake Mounting Nut-Washer Assembly Nev-R-Lube Disc rake Hubs ¹ ₂" Studs, 4mm on ¹ ₂-0 x.0" Press-in Stud (hubs after /0)

78 Recommended Wheel Clearance for,000 Lb. Disc rake Hubface Wheel Mounting Surface Dia Dia lbs. capacity CAUTION: The above hub/rotor profile shows the minimum clearance needed to insure that no part of the wheel makes contact with any brake component. Make sure the wheel is in full contact with the hub face and does not drag against the brake caliper. If there is not full contact with the hub face, you may experience a dangerous wheel separation.

79 Disc rake for,000 Lb. Axles lbs. capacity 1 4 CSA approved at 000#/14.0 SLR Exp000disc_ Disc rake 000# LH Anchor Yoke RH Anchor Yoke (shown) K Caliper Assembly Kit for LH or RH Contains: Caliper Mounting Nut Caliper Mounting olt Cotter Ring Tube Clamp Anti-Rattle Spring leeder Screw Adapter Fitting Pad Retaining Pin Cross Over Hydraulic Line (yokes with notch) Hex olt Assembled Caliper Half 3 K rake Pad Kit (axle set) ³ ₈" rake Mounting Nut-Washer Assembly Disc rake Hubs & Studs Grease ¹ ₂" Studs on Oil ¹ ₂" Studs on Grease ⁹ ₁₆" Studs on Oil ⁹ ₁₆" Studs on Grease ⁵ ₈" Studs on Oil ⁵ ₈" Studs on ¹ ₂-0 x 1.4" Press-in Stud ⁹ ₁₆-1 x.01" Press-in Stud ⁵ ₈-1 x.0" Press-in Stud

80 Recommended Wheel Clearance for,000 Lb. Disc rake Hubface Wheel Mounting Surface Dia Dia Dia lbs. capacity CAUTION: The above hub/rotor profile shows the minimum clearance needed to insure that no part of the wheel makes contact with any brake component. Make sure the wheel is in full contact with the hub face and does not drag against the brake caliper. If there is not full contact with the hub face, you may experience a dangerous wheel separation.

81 AIRFLEX Light Trailer Suspension System lbs. capacity Smooth Out the Roughest Roads Soft Ride New hybrid suspension combines air and rubber torsion for an excellent ride Independent Ride and stability improve with independent wheel action Equalizing Axle-to-axle load equalization allows use on triple axle trailers Reliable Rubber cushions ride even if air is not available Maintains constant ride height for the ultimate ride Fully assembled for easy installation Adjustable axle alignment feature Available for single, tandem or triple axle applications Optional ride height control valve and air generation kits are available year limited warranty 0

82 AIRFLEX for,000 Lb. Axles efore May 010 Service Parts Only lbs. capacity ExpAIRFLEX_-0 AIRFLEX Suspension Components 000# Item Part No. Qty/Axle Description LH Suspension Assembly (shown) (incl. items #-11) RH Suspension Assembly (incl. items #-11) Air Spring & Mounting Hardware Air Spring ¾"-1 Jam Nut ¾" Lock Washer ½"-13 Hex Nut ½" Lock Washer ½"-13 Hex olt Suspension Mounting Hardware Side Mount racket ⁵ ₈" Mounting olt ⁵ ₈" Locknut ⁵ ₈" Washer Axle Attaching Hardware ³ ₄" U-olt ³ ₄" Locknut Tie Plate Air Supply Kits ns K Tandem Plumbing Kit with Ride Height Control Valve ns K Air Generation Kit (includes compressor and tank) ns K Manual Dump Valve Kit ns K Tri-Axle Conversion Plumbing Kit ns - not shown 1

83 AIRFLEX for,000 Lb. Axles After May lbs. capacity 3 LH Torsion Axle Height Control Valve Kit See Kit Instructions Ordered with Suspension RH ExpAirflex_-10 Note: All dimensions are shown at the design height position. Tube Cross Member 3½" x 3½" olt Torque Chart Size Ft. Lbs. ⅜-1 ¾ FORWARD AIRFLEX Suspension Components 000# Item Part No. Qty/Axle Description 1 n/a 1 Torsion Axle with Suspension rackets RH Frame racket LH Frame racket Channel, Air Spring Support W Firestone Air Spring Pivot ushing Kit ushing Spacer/Liner n/a ³ ₄-10 UNC x 4." LG HHCS n/a ³ ₄-10 UNC Stover Lock Nut 10 n/a ³ ₈-1 UNC x 1." LG HHCS 11 n/a ³ ₈ Regular Split Lock Washer 1 n/a ³ ₈-1 UNC x 1" LG HHCS 13 n/a ¹ ₄ NPTM x ¹ ₄ T 0 Elbow, Swivel 14 n/a ¹ ₄ x." LG Nylon Tube 1 n/a Grommet 1 n/a ¹ ₄ T Union Tee 1 n/a ¹ ₄ T Plug Air Supply Kits ns K Ride Height Control Kit ns K Air Supply and Control Kit ns K Air Control Kit Without Air Supply ns Installation Instructions (available on Dexter website) n/a - not available ns - not shown

84 General Applications 00 lbs. capacity Axle Types 00 Lbs. Capacity Complete service manual Precision machined steel spindles and integral cast iron hub/drums Finned brake drums for better heat dissipation Press-in wheel studs, ⁹ ₁₆" or ⁵ ₈" Improved bearing package; unitized seals Standard grease lubrication; optional oil bath; E-Z Lube option 1¹ ₄" x ¹ ₂" electric brakes, CSA approved at 100 lbs. Inner wiring system for easier installation and protection of brake wiring d leaf spring Heavy wall 3" diameter tube Straight or Drop spindles (4" drop only) High quality alloy steel springs in a variety of capacities Single, tandem, or triple axle assemblies with equalized suspensions Slipper leaf spring suspension Heavy duty suspension parts available Optional rubber bushed suspension Optional hanger and attaching parts kits available Durable, wear-resistant components year limited warranty 1V Totally rubber-cushioned for smooth, quiet, independent ride Easy installation with less maintenance Less transfer of road shock which insulates cargo from road shocks and vibration Rubber cords compounded for maximum dependability and durability Load-carrying cross member Self-damping action Independent wheel suspension system year limited warranty on suspension system Low profile for maximum road clearance Various starting angles to control trailer height High and low profile brackets with optional mounting brackets are available Rubber cushioning eliminates metal-to-metal contact Shock absorption provided by the natural hysteresis of rubber Single or tandem axle assemblies Durable, wear-resistant components CAUTION: Triple axle assemblies are NOT recommended for #1V Torflex axles. 3

85 Torflex Application Information 00 lbs. capacity 1V Start Angle Articulation Dimensions Dimensions are for top mount only. Side mount is.31" higher. Allow 3" bump clearance from full load. racket Profile Forward No Load Full Load Shock Load H L H L H L Left Hand Assembly Shown DEXTER Arm Length Axle Location L H Top of racket Center of Spindle Start Angle 4 Down Low High Down. Down Low High Low High #1V Overhang Per Side Spindle Min. Max. Standard.00" 14." 10 Down Low High Low High Up. Up Low High Low High Note: Positive numbers in the H column indicate the spindle is ELOW the top of the bracket. Conversely, negative numbers are AOVE the top of the bracket. 1V Full Load Dimensions Dimensions are for low profile, top mount only. High profile brackets are." higher. Side mount is.31" higher. Allow 3" bump clearance from full load. Top of racket C H E D Top of racket C H E D C Top of racket H E D 10 DN, 0 10 Up,. Up. Dn, 4 Dn Start Angle * * * 4 Down. Down 10 Down 0 10 Up. Up Tire D E H C H C H C H C H C H C LT3/R LT LT Columns D and E are dimensional examples only: * D Static Loaded Radius ** E Inflated Radius 4

86 Torflex Application Information 1V racket Dimensions Forward For Wiring Access olt Size J A G A D E Low Profile 00 lbs. capacity C 1/ G Right Hand Side of Axle Shown F Side Mount Hanger #1V racket Dimensions Low High A C.0.0 D E F G.0.0 J.0.0 N P Q olt Size ⁵ ₈" bolt Tube Size P E F N High Profile Q

87 Leaf Spring Application Information 00 lbs. capacity Double Eye Springs For Standard 33" Axle Spacing Single A/P-1-00 Tandem A/P Triple A/P Spring Length 1" 4" " A C D E For Optional 3" Axle Spacing Tandem A/P-4-00 Triple A/P D Overhang Per Side Min. Max. Straight.00".00" 4" Drop.".00" Nev-R-Lube.00".00" Forward Z Y SLR D H Z Y SLR C D A H Spring Length 1" 4" " C D E Z Y SLR H E D C C Double Eye Axle Assemblies Hanger Kits Quantity Per Kit Part No. Description Height HGR HGR-1-00 HGR-4-00 HGR Hanger 4." Front Hanger 1.44" Hanger.00" Rear Hanger.1" Attaching Parts Kits Part No. Description A/P-1-00 A/P A/P-4-00 A/P A/P Flange Locknut Shackle olt Equalizer Equalizer Equalizer Equalizer Shackle Link Shackle Link, Long Shackle Link Assembly Shackle Link Assembly, Long For 3" axle spacing using " springs

88 Leaf Spring Application Information Slipper Spring Axle Assemblies Hanger Kits Quantity Per Kit Part No. Description Height HGR HGR-3-00 HGR Front Hanger.00" Center Hanger 4.0" Rear Hanger.3" Attaching Parts Kits Part No. Description A/P A/P-0-00 A/P-1-00 A/P A/P ⁹ ₁₆-1 Locknut Keeper Nut Equalizer Nut Equalizer olt Keeper olt Spring Eye olt Equalizer Equalizer For 33." axle spacing For 3" axle spacing 00 lbs. capacity A Slipper Springs Single Tandem Triple A/P A/P-0-00 A/P-1-00 A/P A/P A C D E Note: All " wide slipper springs For 33." axle spacing For 3" axle spacing Z Y SLR D H Z A,, E Hanger Spacing C Axle Spacing D Axle Location H Center of Spindle Y Frame Height Z Top of Tire to ottom of Frame SLR Static Load Radius To determine these values, contact your local sales engineer or distributor to run ProSpec. Z Forward Y SLR D E C Some combinations of hangers and spring mountings may result in insufficient bump clearance. Refer to the Miscellaneous section for additional hanger kits, A/P kits, or other tires. Y SLR D C E D Overhang Per Side Min. Max. Straight.00".00" 4" Drop.".00" Single Axles require 1 HAP kit Tandem Axles require 1 HAP kit and 1 HAP-0-01 kit Triple Axles require 1 HAP kit and HAP-0-01 kits Rubber ushed Suspension Part No. Description Height HAP HAP Front Hanger.0" Center Hanger 4.0" Rear Hanger 4." ⁵ ₁₆-1 UNC Locknut ⁵ ₈-11 UNC Locknut UNC Locknut Keeper olt Spring Eye olt Equalizer olt Equalizer Decal Instruction Sheet

89 Hub Group 00 lbs. capacity Exp00_ A C D Grease Lube Parts Item Part No. Description Seal Inner earing Cone Inner earing Cup Outer earing Cup Outer earing Cone Spindle Nut Cotter Pin (not used with E-Z Lube ) Grease Cap A Grease Cap for E-Z Lube E-Z Lube Rubber Plug Spindle Washer Special Jam Nut for E-Z Lube (after 00) Spindle Nut Retainer for E-Z Lube (after 00) Oil Lube Parts Item Part No. Description Seal (Unitized) Inner earing cone Inner earing Cup Outer earing Cup Outer earing Cone Spindle Nut Cotter Pin Spindle Washer C Oil Cap D Oil Cap Plug ns Oil Filler Plug (service part only) O Ring for Oil Lube Studs & Wheel Nuts Item Part No. Description ¹ ₂-0 Press-in Stud ⁵ ₈-1 Press-in Stud ⁹ ₁₆-1-1 Press-in Stud ⁹ ₁₆-1 0 Cone Nut ⁵ ₈-1 0 Cone Nut ns ⁵ ₈-1 Flange Nut Note: Spindle is not available for resale. Hubs (After May 000 for cast backing plate brakes) Item Part No. Description olt Circle Grease ¹ ₂" Stud on Grease ⁹ ₁₆" Stud on Grease ⁵ ₈" Stud on Oil ¹ ₂" Stud on Oil ⁹ ₁₆" Stud on Oil ⁵ ₈" Stud on.0 rakes (After May 000 with cast backing plate brakes) Item Part No. Description Dust Shield not included with brake assembly 0 K RH 1¼" x ½" Electric rakes 0 K LH 1¼" x ½" Electric rakes Service Parts Not Interchangeable With Cast Parts Hubs (efore May 000 for stamped backing plate brakes) Item Part No. Description olt Circle Grease ⁹ ₁₆" Stud on Grease ⁵ ₈" Stud on Oil ⁹ ₁₆" Stud on Oil ⁵ ₈" Stud on.0 rakes (efore May 000 with stamped backing plate brakes) Item Part No. Description Dust Shield (top) included with brake assembly Dust Shield (bottom) included with brake assembly RH 1¼" x ½" Electric rakes LH 1¼" x ½" Electric rakes ns - not shown

90 Nev-R-Lube Hub Group Exp00nvr_ lbs. capacity Nev-R-Lube Parts 0MM Item Part No. Description Spindle Washer Spindle Nut Washer, Torque Label Snap Ring Grease Cap 1¹ ₄" x ¹ ₂" rakes Item Part No. Description Dust Shield 0 K3-4-00/K LH/RH Manual Adjust Electric rake Note: Spindle is not available for resale. Wheel Nuts Item Part No. Description ⁹ ₁₆-1 0 Cone Nut ns ⁵ ₈-1 0 Cone Nut ns ⁵ ₈-1 Flange Nut ns - not shown Hubs With earing and Wheel Studs Item Part No. Description olt Circle Hub and Drum includes: on ⁹ ₁₆" Press-in Studs mm earing Cartridge earing Retainer ns Hub and Drum includes: ⁵ ₈" Press-in Studs mm earing Cartridge earing Retainer on.0

91 1¹ ₄" x ¹ ₂" Electric rake Cast acking Plate 00 lbs. capacity xECast_ CSA approved at 100#/14. SLR Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly 1 K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining 1 K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining acking Plate Shoe Return (gray) LH Actuating Lever Arm Assembly RH Actuating Lever Arm Assembly Wire Clip LH Lever Arm Retainer RH Lever Arm Retainer Flange Nut K Magnet Kit Contains: 1 # Magnet 1 # Magnet Retainer 1 # Magnet Spring Centering Spring Adjuster Spring (red) Adjuster Assembly * Dust Shield (sold separately) * Adjuster Slot Plug * Magnet Wire Grommet * rake Mounting olt * Hex Nut * Lock Washer Washer * Not included with complete brake assembly. Item sold separately. rakes manufactured after May 000 use the cast backing plate 0

92 1¹ ₄" x ¹ ₂" Electric rake Stamped acking Plate Service Parts Only 1xEStamped_-0 1 CSA approved at 100#/14. SLR lbs. capacity Electric rake Service Parts Only RH Complete rake Assembly (obsolete-no longer available) LH Complete rake Assembly (obsolete-no longer available) 1 K Shoe & Lining Kit Contains: 1 # RH Primary S&L or LH Secondary S&L 1 # LH Primary S&L or RH Secondary S&L # Shoe Hold Down Washer # Locknut K Magnet Kit Contains: 1 # Magnet 1 # Magnet Retainer 1 # Magnet Spring 3 K Adjusting Screw Kit Contains: 1 # Adjuster Spring (red) 1 # Adjuster Assembly 4 K rake Spring Kit Contains: 1 # Shoe Return (gray) 1 # Magnet Spring # Centering Spring 1 # Adjuster Spring (red) Wire Clip LH Lever Arm Retainer RH Lever Arm Retainer Flange Nut Adjuster Slot Plug Magnet Wire Grommet Washer Note: Only numbered items are available. rakes manufactured before May 000 use the stamped backing plate 1

93 AIRFLEX Light Trailer Suspension System 00 lbs. capacity Smooth Out the Roughest Roads Soft Ride New hybrid suspension combines air and rubber torsion for an excellent ride Independent Ride and stability improve with independent wheel action Equalizing Axle-to-axle load equalization allows use on triple axle trailers Reliable Rubber cushions ride even if air is not available Maintains constant ride height for the ultimate ride Fully assembled for easy installation Adjustable axle alignment feature Available for single, tandem or triple axle applications Optional ride height control valve and air generation kits are available year limited warranty

94 AIRFLEX for,00 Lb. Axles After May LH Torsion Axle Height Control Valve Kit See Kit Instructions Ordered with Suspension RH 00 lbs. capacity ExpAirflex_-10 Note: All dimensions are shown at the design height position. Tube Cross Member 3½" x 3½" olt Torque Chart Size Ft. Lbs. ⅜-1 ¾ FORWARD AIRFLEX Suspension Components 00# Item Part No. Qty/Axle Description 1 n/a 1 Torsion Axle with Suspension rackets RH Frame racket LH Frame racket Channel, Air Spring Support W Firestone Air Spring Pivot ushing Kit ushing Spacer/Liner n/a ³ ₄-10 UNC x 4." LG HHCS n/a ³ ₄-10 UNC Stover Lock Nut 10 n/a ³ ₈-1 UNC x 1." LG HHCS 11 n/a ³ ₈ Regular Split Lock Washer 1 n/a ³ ₈-1 UNC x 1" LG HHCS 13 n/a ¹ ₄ NPTM x ¹ ₄ T 0 Elbow, Swivel 14 n/a ¹ ₄ x." LG Nylon Tube 1 n/a Grommet 1 n/a ¹ ₄ T Union Tee 1 n/a ¹ ₄ T Plug Air Supply Kits ns K Ride Height Control Kit ns K Air Supply and Control Kit ns K Air Control Kit Without Air Supply ns Installation Instructions (available on Dexter website) n/a - not available ns - not shown 3

95 General Applications 000 lbs. capacity Axle Types 000 Lbs. Capacity Complete service manual Precision machined steel spindles and integral cast iron hub/drums Standard oil bath lubrication; grease or Nev-R-Lube option Press-in wheel studs, ⁹ ₁₆" or ⁵ ₈" Hydraulic brakes are available with and without parking feature Hydraulic brakes uni-servo and duo-servo available Hydraulic disc brakes available 1¹ ₄" x 3³ ₈" self adjusting electric and hydraulic brakes Inner wiring system for easier installation and protection of brake wiring Heavy wall 3½" diameter tube Straight or Drop spindles (4" drop only) High quality alloy steel springs in a variety of capacities Single, tandem or triple axle assemblies with equalized suspensions d0 leaf spring Slipper leaf spring suspension Heavy duty suspension parts available Optional rubber bushed suspension Optional hanger and attaching parts kits available Durable, wear-resistant components year limited warranty 13 13T Totally rubber-cushioned for smooth, quiet, independent ride Easy installation with less maintenance Less transfer of road shock which insulates cargo from road shocks and vibration Rubber cords compounded for maximum dependability and durability Load-carrying cross member Self-damping action Independent wheel suspension system year limited warranty on suspension system Low profile for maximum road clearance Various starting angles to control trailer height High and low profile brackets with optional mounting brackets are available Rubber cushioning eliminates metal-to-metal contact Shock absorption provided by the natural hysteresis of rubber Single or tandem axle assemblies Durable, wear-resistant components CAUTION: Triple axle assemblies are NOT recommended for #13 Torflex axles, however the #13T axle is designed for triple applications. 4

96 Torflex Application Information 13 13T Articulation Dimensions Dimensions are for top mount only. Side mount is.31" higher. Allow 3" bump clearance from full load. Note: #13T is not available with low profile. Start Angle 4 Down 3 Down. Down 10 Down 0 racket Profile Forward No Load Full Load Shock Load H L H L H L Low High Low High Low High Low High Low High Left Hand Assembly Shown DEXTER Arm Length Axle Location #13 Overhang Per Side Spindle Min. Max. Short.0" 1.0" Standard.00" 1.0" L H Top of racket Center of Spindle #13T Overhang Per Side Spindle Min. No racket Zone Max. Short." 10.13" - 10." 11." Standard." 10.3" - 11." 1." Start Angle 000 lbs. capacity 10 Up. Up 13 Low High Low High T Note: Positive numbers in the H column indicate the spindle is ELOW the top of the bracket. Conversely, negative numbers are AOVE the top of the bracket. Full Load Dimensions Dimensions are for low profile, top mount only. High profile brackets are." higher. Side mount is.31" higher. Allow 3" bump clearance from full load. Top of racket C H E D Top of racket C H E D C Top of racket H E D 10 DN, 0 10 Up,. Up. Dn, 4 Dn Start Angle * * * 4 Down. Down 10 Down 0 10 Up. Up Tire D E H C H C H C H C H C H C 10R1.HC /R LT LT R 1.HC Columns D and E are dimensional examples only: * D Static Loaded Radius ** E Inflated Radius

97 Torflex Application Information 000 lbs. capacity 13 13T racket Dimensions Forward For Wiring Access olt Size J A G A D E Low Profile L C 1/ G Right Hand Side of Axle Shown F Side Mount Hanger #13 racket Dimensions Low High A C D E F G.0.0 J.. L.. P Q olt Size ⁵ ₈" bolt Tube Size P E F Q High Profile

98 Leaf Spring Application Information Double Eye Springs For Standard 33" Axle Spacing Single A/P-1-00 Tandem A/P Triple A/P Spring Length 1" 4" " A C D E For Optional 3" Axle Spacing Tandem A/P-4-00 Triple A/P D0 Overhang Per Side Min. Max. Straight.00".0" 4" Drop.00".0" Nev-R-Lube.00".0" * Minimum overhang with disc brakes Forward Z Y SLR D H Z Y SLR C D A H 000 lbs. capacity Spring Length 1" 4" " C D E Z Y SLR H E D C C Double Eye Axle Assemblies Hanger Kits Quantity Per Kit Part No. Description Height HGR HGR-1-00 HGR-4-00 HGR Hanger 4." Front Hanger 1.44" Front Hanger.00" Rear Hanger.1" Attaching Parts Kits Part No. Description A/P-1-00 A/P A/P-4-00 A/P A/P Flange Locknut Shackle olt Equalizer Equalizer Equalizer Equalizer Shackle Link Shackle Link, Long Shackle Link Assembly Shackle Link Assembly, Long For 3" axle spacing using " springs

99 Leaf Spring Application Information 000 lbs. capacity Slipper Spring Axle Assemblies Hanger Kits Quantity Per Kit Part No. Description Height HGR HGR-3-00 HGR Front Hanger.00" Center Hanger 4.0" Rear Hanger.3" Attaching Parts Kits Part No. Description A/P A/P-0-00 A/P-1-00 A/P A/P ⁹ ₁₆-1 Locknut Keeper Nut Equalizer Nut Equalizer olt Keeper olt Spring Eye olt Equalizer Equalizer For 33." axle spacing For 3" axle spacing A Slipper Springs Single Tandem Triple A/P A/P-0-00 A/P-1-00 A/P A/P A C D E Note: All " wide slipper springs For 33." axle spacing For 3" axle spacing Z Y SLR D H Z A,, E Hanger Spacing C Axle Spacing D Axle Location H Center of Spindle Y Frame Height Z Top of Tire to ottom of Frame SLR Static Load Radius To determine these values, contact your local sales engineer or distributor to run ProSpec. Z Forward Y SLR D E C Some combinations of hangers and spring mountings may result in insufficient bump clearance. Refer to the Miscellaneous section for additional hanger kits, A/P kits, or other tires. Y SLR D C E D0 Overhang Per Side Min. Max. Straight.00".0" 4" Drop.00".0" Single Axles require 1 HAP kit Tandem Axles require 1 HAP kit and 1 HAP-0-01 kit Triple Axles require 1 HAP kit and HAP-0-01 kits Rubber ushed Suspension Part No. Description Height HAP HAP Front Hanger.0" Center Hanger 4.0" Rear Hanger 4." ⁵ ₁₆-1 UNC Locknut ⁵ ₈-11 UNC Locknut UNC Locknut Keeper olt Spring Eye olt Equalizer olt Equalizer Decal Instruction Sheet

100 Hub Group Exp000_ D C 1 1 A 000 lbs. capacity 13 Grease Lube Parts Item Part No. Description Seal Inner earing Cone Inner earing Cup Outer earing Cup Outer earing Cone Spindle Nut Cotter Pin (not used with E-Z Lube ) ns Grease Cap A Grease Cap for E-Z Lube E-Z Lube Rubber Plug Spindle Washer Special Jam Nut for E-Z Lube (after 00) Spindle Nut Retainer for E-Z Lube (after 00) Oil Lube Parts Item Part No. Description Seal (Unitized) Inner earing Cone Inner earing Cup Outer earing Cup Outer earing Cone Spindle Nut Cotter Pin C Oil Cap D Oil Cap Plug Spindle Washer ns Oil Filler Plug (service part only) O Ring for Oil Lube AS Components Part No. Description Sensor, Straight Sensor lock, Screw-In Sensor Retainer Clip Sensor Tone Ring Note: Spindle is not available for resale. 1¹ ₄" x 3³ ₈" rakes Item Part No. Description Dust Shield Dust Shield for brakes with park 0 K /K LH/RH Electric Self-Adjust ns K /K LH/RH Electric Manual Adjust ns K /K LH/RH Hydraulic Self-Adjust Duo-Servo ns K /K LH/RH Hyd. Self-Adj Duo-Servo w/park ns K /K LH/RH Hydraulic Uni-Servo ns K3--00/K LH/RH Hydraulic Uni-Servo w/park ns K /K LH/RH Self Adj. DS Corrision Resistant ns K3-3-00/K LH/RH Hyd. Manual Adjust Duo-Servo Hubs Item Part No. Description olt Circle Hubs and Drums Grease ⁵ ₈" Stud on Grease ⁵ ₈" Stud AS on Grease ⁹ ₁₆" Stud on Grease ⁹ ₁₆" Stud AS on Oil ⁵ ₈" Stud on Oil ⁵ ₈" Stud AS on Oil ⁹ ₁₆" Stud on Oil ⁹ ₁₆" Stud AS on.0 Plain Hubs ns Grease ⁵ ₈" Stud on.0 ns Grease ⁹ ₁₆" Stud on.0 ns Oil ⁹ ₁₆" Stud on.0 ns Oil ⁵ ₈" Stud on.0 Studs & Wheel Nuts Item Part No. Description Nut Torque ⁹ ₁₆-1 0 Cone Nut * ⁵ ₈-1 0 Cone Nut 00 lbs.-ft * Clamp Ring ⁹ ₁₆-1 Press-in Stud ⁵ ₈-1 Press-in Stud ns ⁵ ₈-1 Flange Nut ns - not shown * Must use the 0 cone nut with the clamp ring. Alternate fastener is just the flange nut.

101 Nev-R-Lube Hub Group 000 lbs. capacity Exp000nvr_ Nev-R-Lube Parts 0MM Item Part No. Description Spindle Washer Spindle Nut Washer, Torque Label Snap Ring Grease Cap 1¹ ₄" x 3³ ₈" rakes Item Part No. Description Dust Shield Dust Shield for brakes with park 0 K /K LH/RH Electric Self-Adjust ns K /K LH/RH Hydraulic Self-Adjust Duo-Servo ns K /K LH/RH Hyd. Self-Adj Duo-Servo w/park ns K /K LH/RH Hydraulic Uni-Servo ns K3--00/K LH/RH Hydraulic Uni-Servo w/park AS Hubs Without earing Item Part No. Description olt Circle Grease ⁵ ₈" Stud AS on Grease ⁹ ₁₆" Stud AS on.0 Note: Spindle is not available for resale. Hubs With earing and Wheel Studs Item Part No. Description olt Circle Hub and Drum includes: on ⁹ ₁₆" Press-in Studs mm earing Cartridge earing Retainer ns Hub and Drum includes: on ⁵ ₈" Press-in Studs mm earing Cartridge earing Retainer Wheel Nuts Item Part No. Description ⁹ ₁₆-1 0 Cone Nut ns ⁵ ₈-1 0 Cone Nut AS Components Part No. Description Sensor, Straight Sensor lock, Screw-In Sensor Retainer Clip ns - not shown 100

102 1¹ ₄" x 3³ ₈" K Electric rake FSA Cast acking Plate 1 1 1x4efsacast_ CSA approved at 000#/14. SLR lbs. capacity Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly 1 K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining 1 K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining acking Plate Assembly LH Actuating Arm Assembly RH Actuating Arm Assembly Wire Clip LH Arm/Shoe Retainer RH Arm/Shoe Retainer Flange Nut K Magnet Kit Contains: 1 # Magnet 1 # Magnet Retainer Clip 1 # Magnet Spring Centering Spring Adjuster Cable LH Adjuster Lever RH Adjuster Lever Adjuster Spring LH Adjuster Assembly (silver) RH Adjuster Assembly (gold) * Dust Shield * rake Mounting olt * Adjuster Slot Plug * Wire Grommet Adjuster Clip (barrel end) Adjuster Clip (thread end) * rake Mounting Nut * Lock Washer Return Spring * Not included with complete brake assembly. Item sold separately. rakes manufactured after April 000 use the cast backing plate 101

103 1¹ ₄" x 3³ ₈" K Electric rake Manual Adjust 000 lbs. capacity Cast acking Plate x3EManCast_ CSA approved at 000#/14. SLR Electric rake 0 K LH Complete rake Assembly (shown) 0 K RH Complete rake Assembly 1 K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining 1 K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining acking Plate Assembly LH Actuating Arm Assembly RH Actuating Arm Assembly Wire Clip LH Arm/Shoe Retainer RH Arm/Shoe Retainer Flange Nut K Magnet Kit Contains: 1 # Magnet 1 # Magnet Retainer Clip 1 # Magnet Spring Centering Spring Washer Adjuster Spring Adjuster Assembly * Dust Shield * rake Mounting olt * Adjuster Slot Plug * Wire Grommet Adjuster Clip (thread end) Adjuster Clip (barrel end) * rake Mounting Nut * Lock Washer Return Spring * Not included with complete brake assembly. Item sold separately. rakes manufactured before April 000 use the stamped backing plate 10

104 1¹ ₄" x 3³ ₈" K Hydraulic rake FSA 1x3hydfsa_ A E C D AS Parts Available lbs. capacity Hydraulic rake +0 K LH Complete rake Assembly FSA US +0 K RH Complete rake Assembly FSA US 0 K LH Complete rake Assembly FSA DS (shown) 0 K RH Complete rake Assembly FSA DS * Dust Shield Retainer 3 K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut 3 K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut Shoe Hold Down Screw Adjuster Cable K Wheel Cylinder Kit (1.00" ore) Contains: 1 # Spring # oot # Piston # Cup 1 # leeder Screw or Cylinder Push Rod US (1) DS () LH Spider Assembly US (incl. items #4,, ) RH Spider Assembly US (incl. items #4,, ) Spider Assembly (incl. items #4,, ) DS Retractor Spring LH Adjuster Lever RH Adjuster Lever LH Adjuster Spring RH Adjuster Spring Cable Attachment racket Extension Spring LH Adjuster Assembly RH Adjuster Assembly * rake Mounting olt Piston Stop Adjuster Clip (thread end) Adjuster Clip (barrel end) * Adjuster Slot Plug * rake Mounting Nut * Lock Washer * Not included with complete brake assembly. Item sold separately. + Uni-Servo version not shown. Hydraulic rake Corrosion Resistant Duo-Servo Only 0 K LH Complete rake Assembly FSA 0 K RH Complete rake Assembly FSA * Dust Shield Retainer 3 K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut 3 K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut Shoe Hold Down Screw Adjuster Cable A Spring leeder Screw C Cup D Piston E oot Cylinder Push Rod Spider Assembly (incl. items #4,, ) DS Retractor Spring LH Adjuster Lever RH Adjuster Lever LH Adjuster Spring RH Adjuster Spring Cable Attachment racket Extension Spring LH Adjuster Assembly RH Adjuster Assembly * rake Mounting olt Piston Stop Adjuster Clip (thread end) Adjuster Clip (barrel end) * Adjuster Slot Plug * rake Mounting Nut * Lock Washer 103

105 000 lbs. capacity 1¹ ₄" x 3³ ₈" K Hydraulic rake Manual Adjust 1x3HydMan_1-0 Shown With AS Parts Hydraulic rake 0 K LH Complete rake Assembly-DS (shown) 0 K RH Complete rake Assembly-DS * Dust Shield Retainer 3 K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut 3 K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut Shoe Hold Down Screw K Wheel Cylinder Kit (1.00" ore) Contains: 1 # Spring # oot # Piston # Cup 1 # leeder Screw Cylinder Push Rod Spider Assembly (incl. items #4,, ) Retractor Spring Adjuster Spring Adjuster Assembly * rake Mounting olt * Not included with complete brake assembly. Item sold separately. Hydraulic rake Piston Stop Adjuster Clip (thread end) Adjuster Clip (barrel end) * AS Sensor Mounting lock * AS Sensor Retaining Clip * Adjuster Slot Plug * AS Sensor (straight) Washer * rake Mounting Nut * Lock Washer 104

106 1¹ ₄" x 3³ ₈" K Hydraulic rake With Parking Feature (Manual Adjust) x3HydManPark_ AS Parts Available lbs. capacity Hydraulic rake LH Complete rake Assembly-US, w/park RH Complete rake Assembly-US, w/park LH Complete rake Assembly-DS SA, w/park, RSA RH Complete rake Assembly-DS SA, w/park, RSA * Dust Shield 3 K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut 3 K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut Shoe Hold Down Screw Snap Ring K Wheel Cylinder Kit (1.00" ore) Contains: 1 # Spring # oot # Piston # Cup 1 # leeder Screw Cylinder Push Rod-US LH Spider Assembly (incl. items #4,,,) US RH Spider Assembly (incl. items #4,,,) US ns LH or RH Spider Assembly (incl. items #4,,) US Retractor Spring * Not included with complete brake assembly. Item sold separately. + Uni-servo version not shown. ns - not shown Hydraulic rake Spacer Adjuster Spring Adjuster Assembly * rake Mounting olt * rake Mounting Nut * Lock Washer Adjuster Clip (thread end) Adjuster Clip (barrel end) Hold Down Lever olt Star Washer Hold Down Lever Washer Hold Down Lever Spring Parking Cam LH Parking Cam RH Parking Lever LH Parking Lever RH * Parking Cable racket 10

107 1¹ ₄" x 3³ ₈" K Hydraulic rake RSA With Parking Feature 000 lbs. capacity x3HydRSAPark_ AS Parts Available Hydraulic rake LH Complete rake Assembly-DS SA, w/park, RSA RH Complete rake Assembly-DS SA, w/park, RSA * Dust Shield K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut Shoe Hold Down Screw Snap Ring (for Uni-servo only) K Wheel Cylinder Kit (1.00" ore) Contains: 1 # Spring # oot # Piston # Cup 1 # leeder Screw Cylinder Push Rod-US ns LH Spider Assembly (incl. items #4,,,) US ns RH Spider Assembly (incl. items #4,,,) US LH or RH Spider Assembly (incl. items #4,,,) DS Retractor Spring * Not included with complete brake assembly. Item sold separately. ns - not shown Hydraulic rake Adjuster Spring 10 K LH & RH rake Adjuster Kit Contains: 1 # LH Adjustment Lever Spring 1 # RH Adjustment Lever Spring 1 # LH Adjusting Screw 1 # RH Adjusting Screw # Adjuster Cable- 1 # LH Adjusting Lever 1 # RH Adjusting Lever * rake Mounting olt rake Mounting Nut Lock Washer Adjuster Clip (thread end) Adjuster Clip (barrel end) Hold Down Lever olt Star Washer Hold Down Lever Washer Hold Down Lever Spring Parking Cam LH Parking Cam RH Parking Lever LH Parking Lever RH 10

108 1¹ ₄" x 3³ ₈" K Hydraulic rake Uni-Servo With Parking Feature (Manual Adjust) x3HydManPark_ lbs. capacity Note: Uni-Servo brakes to be used with surge actuator Hydraulic rake 0 K LH Complete rake Assembly-US, w/park (shown) 0 K RH Complete rake Assembly-US, w/park * Dust Shield 3 K LH Shoe & Lining Kit Contains: 1 # LH Primary Shoe & Lining 1 # LH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut 3 K RH Shoe & Lining Kit Contains: 1 # RH Primary Shoe & Lining 1 # RH Secondary Shoe & Lining # Shoe Hold Down Washer # Locknut Shoe Hold Down Screw Snap Ring K Wheel Cylinder Kit (1.00" ore) Contains: 1 # Spring # oot # Piston # Cup 1 # leeder Screw Cylinder Push Rod-US LH Spider Assembly (incl. items #4,,,) US RH Spider Assembly (incl. items #4,,,) US Retractor Spring * Not included with complete brake assembly. Item sold separately. Hydraulic rake Spacer Adjuster Spring Adjuster Assembly * rake Mounting olt * rake Mounting Nut * Lock Washer Adjuster Clip (thread end) Adjuster Clip (barrel end) * Adjuster Slot Plug Hold Down Lever olt Star Washer Hold Down Lever Washer Hold Down Lever Spring Parking Cam LH Parking Cam RH Parking Lever LH Parking Lever RH ns Parking Cable ns - not shown 10

109 Disc rake for,000 Lb. Axles 000 lbs. capacity 1 10 CSA approved at 000#/14.0 SLR 11 Exp000disc_ Disc rake 000# Anchor Yoke K Caliper Assembly Kit for LH or RH Contains: Caliper Mounting Nut Caliper Mounting olt Cotter Ring Tube Clamp Anti-Rattle Spring leeder Screw Adapter Fitting Pad Retaining Pin Cross Over Hydraulic Line (yokes without notch) Cross Over Hydraulic Line (yokes with notch) Hex olt Assembled Caliper Half 3 K rake Pad Kit (axle set) 4 K Rotor Kit ¹ ₂" Lock Washer ¹ ₂" Hex Nut ¹ ₂" rake Mounting olt AS Sensor Retaining Clip AS Sensor (straight) Disc rake Hubs & Studs Grease ⁹ ₁₆" Studs on Oil ⁹ ₁₆" Studs on Grease ⁵ ₈" Studs on Oil ⁵ ₈" Studs on ⁹ ₁₆-1 x.0" Press-in Stud ⁵ ₈-1 x 3.1" Press-in Stud Disc rake 000# With 0MM Nev-R-Lube Anchor Yoke K Caliper Assembly Kit for LH or RH Contains: Caliper Mounting Nut Caliper Mounting olt Cotter Ring Tube Clamp Anti-Rattle Spring leeder Screw Adapter Fitting Pad Retaining Pin Cross Over Hydraulic Line (yokes without notch) Cross Over Hydraulic Line (yokes with notch) Hex olt Assembled Caliper Half 3 K rake Pad Kit (axle set) 4 K Rotor Kit ¹ ₂" Lock Washer ¹ ₂" Hex Nut ¹ ₂" rake Mounting olt AS Sensor Retaining Clip AS Sensor (straight) Nev-R-Lube Disc rake Hubs ⁹ ₁₆" Studs, 0mm on ⁵ ₈" Studs, 0mm on ⁹ ₁₆-1 x.0" Press-in Stud ⁵ ₈-1 x 3.1" Press-in Stud 10

110 Recommended Wheel Clearance for,000 Lb. Disc rake Hubface Wheel Mounting Surface Dia. 14. Dia Dia. 000 lbs. capacity CAUTION: The above hub/rotor profile shows the minimum clearance needed to insure that no part of the wheel makes contact with any brake component. Make sure the wheel is in full contact with the hub face and does not drag against the brake caliper. If there is not full contact with the hub face, you may experience a dangerous wheel separation. 10

111 AIRFLEX Light Trailer Suspension System 000 lbs. capacity Smooth Out the Roughest Roads Soft Ride New hybrid suspension combines air and rubber torsion for an excellent ride Independent Ride and stability improve with independent wheel action Equalizing Axle-to-axle load equalization allows use on triple axle trailers Reliable Rubber cushions ride even if air is not available Maintains constant ride height for the ultimate ride Fully assembled for easy installation Adjustable axle alignment feature Available for single, tandem or triple axle applications Optional ride height control valve and air generation kits are available year limited warranty 110

112 AIRFLEX for,000 Lb. Axles efore May 010 Service Parts Only lbs. capacity ExpAIRFLEX_-0 AIRFLEX Suspension Components 000# Item Part No. Qty/Axle Description LH Suspension Assembly (shown) (incl. items #-11) RH Suspension Assembly (incl. items #-11) Air Spring & Mounting Hardware Air Spring ¾"-1 Jam Nut ¾" Lock Washer ½"-13 Hex Nut ½" Lock Washer ½"-13 Hex olt Suspension Mounting Hardware Side Mount racket ⁵ ₈" Mounting olt ⁵ ₈" Locknut ⁵ ₈" Washer Axle Attaching Hardware ³ ₄" U-olt ³ ₄" Locknut Tie Plate Air Supply Kits ns K Tandem Plumbing Kit with Ride Height Control Valve ns K Air Generation Kit (includes compressor and tank) ns K Manual Dump Valve Kit ns K Tri-Axle Conversion Plumbing Kit ns - not shown 111

113 AIRFLEX for,000 Lb. Axles After May lbs. capacity 3 LH Torsion Axle Height Control Valve Kit See Kit Instructions Ordered with Suspension RH ExpAirflex_-10 Note: All dimensions are shown at the design height position. Tube Cross Member 3½" x 3½" olt Torque Chart Size Ft. Lbs. ⅜-1 ¾ FORWARD AIRFLEX Suspension Components 000# Item Part No. Qty/Axle Description 1 n/a 1 Torsion Axle with Suspension rackets RH Frame racket LH Frame racket Channel, Air Spring Support W Firestone Air Spring Pivot ushing Kit ushing Spacer/Liner n/a ³ ₄-10 UNC x 4." LG HHCS n/a ³ ₄-10 UNC Stover Lock Nut 10 n/a ³ ₈-1 UNC x 1." LG HHCS 11 n/a ³ ₈ Regular Split Lock Washer 1 n/a ³ ₈-1 UNC x 1" LG HHCS 13 n/a ¹ ₄ NPTM x ¹ ₄ T 0 Elbow, Swivel 14 n/a ¹ ₄ x." LG Nylon Tube 1 n/a Grommet 1 n/a ¹ ₄ T Union Tee 1 n/a ¹ ₄ T Plug Air Supply Kits ns K Ride Height Control Kit ns K Air Supply and Control Kit ns K Air Control Kit Without Air Supply ns Installation Instructions (available on Dexter website) n/a - not available ns - not shown 11

114 Wheels and Tires Wheel Dia. Rim Width Contour Tire Size Description SLR Tire Radius Width Capacity PSI 1 4JA 4.0-1, JA.30-1, C JJ ST1/0R13, JJ ST1/0R13, C wheels & tires 14.JJ ST0/R14, C JJ ST1/R14, C MH -14.LT, E MH -14.LT, F MH -14.LT, E MH -14.LT, F JJ ST0/R1, JJ ST0/R1, C JJ LT1/R1, C JJ ST/R1, D JJ LT3/R1, E K LT/R1, E K LT3/R1, E K LT3/R1, G LT, E LT, F HC 1/R HC 3/R

115 hanger & ap kits Hanger and Attaching Parts Kits Double Eye Leaf Springs Hanger Heights Hanger Kit Axle Combination Front Height Center Height Notes HGR N/A K Max. HGR N/A K Max. HGR N/A.K Max. HGR K Max. HGR K Max. HGR K Max. HGR K Max. HGR Max. HGR K Max. HGR K Max. HGR K Max. HGR K Max. HGR K Max. HGR K Max. Attaching Parts Kits 33" Axle Spacing 3" Axle Spacing Capacity Single Tandem Triple Tandem Triple D0 A/P-1-00 A/P A/P N/A N/A D3 A/P-1-00 A/P A/P A/P-4-00 N/A D A/P-1-00 A/P A/P A/P-4-00 A/P D0 A/P-1-00 A/P A/P A/P-4-00 A/P D0 A/P-1-00 A/P A/P A/P-4-00 A/P D A/P-1-00 A/P A/P A/P-4-00 A/P D0 A/P-1-00 A/P A/P A/P-4-00 A/P Tube Diameter & Spring Pad Height DE and SS Capacity Tube Dia. Standard Tube Dia. Optional Pad Ht. Standard Pad Ht. Optional D D D 3.00 N/A 0.0 N/A D N/A 0.0 N/A D D D0 3.0 N/A 0.0 N/A N/A - not applicable Stack & Loaded Arch Heights Capacity Part Number Stack Height Length (Inches) Axle Location Loaded Arch Height Length Loaded Arch Stack Shackle Link Center Hanger Front Hanger Tie Plate Equalizer U-olt Shackle olts Rear Hanger Underslung Shown 114

116 Hanger and Attaching Parts Kits Slipper Leaf Springs Hanger Heights Hanger Kit Axle Combination Front Height Center Height Notes HAP K Max. HGR N/A.K Max. HGR N/A K Max. HGR N/A K Max. HGR K Max. HAP K Max. HGR K Max. HGR K Max. HGR K Max. Attaching Parts Kits 33." Axle Spacing 3" Axle Spacing Capacity Single Tandem Triple Tandem Triple D0 A/P N/A N/A N/A N/A D3 A/P A/P-0-00 A/P N/A N/A D A/P A/P-0-00 A/P A/P-1-00 A/P D0 A/P A/P-0-00 A/P A/P-1-00 A/P D0 A/P A/P-0-00 A/P A/P-1-00 A/P D A/P A/P-0-00 A/P A/P-1-00 A/P D0 A/P A/P-0-00 A/P A/P-1-00 A/P Tube Diameter & Spring Pad Height DE and SS Capacity Tube Dia. Standard Tube Dia. Optional Pad Ht. Standard Pad Ht. Optional D D D 3.00 N/A 0.0 N/A D N/A 0.0 N/A D D D0 3.0 N/A 0.0 N/A N/A - not applicable Stack & Loaded Arch Heights Capacity Part Number Stack Height Width (Inches) Axle Location Loaded Arch Height * * Rubber ushed hanger & ap kits Loaded Arch Stack Equalizer Center Hanger Front Hanger Tie Plate U-olt U-olt Tie Plate Rear Hanger Spring Eye olts Keeper olts Overslung Shown 11

117 Torflex Installation torflex installation The following instructions describe methods that can be used to attach your Torflex axles to the vehicle frame. Step 1: The user must first decide where to place the axle(s) on the trailer. The position of the wheel center relative to the CG (center of gravity) will determine the final axle loading as well as the hitch load. Step : Determine the method of attachment you wish to use. a. For structural tube type frame rails, refer to Figure 1 for the recommended attachment. b. For C channel or I beam type frame, refer to Figure. Step 3: Once the method of attachment is decided, the axle(s) must be carefully aligned on the trailer frame. The axle(s) centerline must be perpendicular to the longitudinal centerline of the trailer. See figure 3. CAUTION: Misalignment of the axle(s) can cause poor tracking and accelerated tire wear. Attachment to Structural Tube Type Frame a. Dexter Axle recommends the use of side mounting hangers when mounting axles to tubular type frames. These hangers provide a convenient means for bolting the axles in place. All of the necessary components are included in the Side Mount A/P Kits listed in Chart 1. b. Refer to Chart to find the mounting bracket dimensions of your axles. This chart shows the dimensions from the wheel center to the bolt holes of the brackets. c. The preferred way to use the side mount hanger is to pre assemble the hangers to the axle using the hardware provided in the A/P kit. Make sure the hangers are clamped firmly against the axle brackets and the bolts are tightened to the torque specifications shown in Chart 1. Position the axle assembly on the frame rails in the desired location and weld the side mount hangers to the frame. d. Axle bracket position is the distance as measured over the outboard edges of the brackets. This dimension is usually matched to the outside measurement of the frame members but depending on the type of frame may not always be suitable. The preferred arrangement should place the longest vertical section of the axle bracket directly under the most rigid section of the frame member. Side Mount Installation OUTSIDE FRAME OUTSIDE RACKET DIMENSION Washer(s) must be placed against the slotted hole in the axle bracket. NOTE: Low profile brackets have plain round holes. Figure 1 Side mount hangers should be welded to frame with three (3) ¹ ₄" fillet welds, ¹ ₂" long on each side of the hanger and a fillet weld on each end. Welds should meet the quality standards of the American Welding Society, D1.1, Structural Welding Code. 11

118 Torflex Installation Axle Size A/P Kit Top Mount Chart 1 Attaching Parts Kits and Torque Specifications A/P Kit Side Mount A/P Kit Side Mount Aluminum olt Size Torque Lb-Ft. # A/P A/P-1-00 A/P /" 0-0 # A/P A/P-1-00 A/P /" 0-0 #10 A/P A/P-1-00 A/P /" 10-1 #10L A/P A/P-1-00 A/P /" 10-1 #10F A/P A/P-1-00 A/P /" 10-1 #11 A/P A/P-1-00 A/P-1-00 /" 10-1 #1 A/P A/P-1-00 A/P /" 10-1 #1T A/P A/P-1-00 /" 10-1 #1V A/P A/P-1-00 /" 10-1 #13 A/P A/P-1-00 /" 10-1 #13T A/P A/P-1-00 /" 10-1 Side mount hangers and fasteners for mounting axle are provided in the A/P Attaching Parts Kits shown in Chart 1. Torque fasteners to levels specified in Chart 1. Attachment to Structural Tube Type Frame a. Refer to Chart to find the mounting bracket dimensions of your axles. This chart shows the dimensions from the wheel center to the bolt holes of the brackets. b. Lay out the bolt hole locations on the bottom flanges of the frame rails. Make sure the hole pattern matches the mounting brackets of your axles and is properly oriented to allow proper alignment of the axle(s). c. An alternate method for determining hole location is to position the axle assembly on the frame rails, align it perpendicular to the trailer centerline, clamp in place and transfer the holes directly from the brackets. d. Drill the holes through the frame rails and attach the axle using the hardware provided in the A/P kit. Tighten the bolts to the torque specified in Chart 1. CAUTION: When bolting to structural shapes that have tapered flanges, bevel washers must be used to prevent uneven clamping and bending of the fasteners. Note: In the unlikely event a Torflex axle must be replaced during the warranty period, Dexter Axle cannot assume responsibility for additional costs incurred for removal and reinstallation of axles that have been welded directly to the frame. torflex installation Top Mount Installation C channel frames should be reinforced in the area over the axle(s). Use bevel washers when bolting to structural steel. Figure CAUTION: C channel and I beam type frame sections should be reinforced in the area over the axle mounting brackets. It is recommended that the vertical leg of the axle bracket be positioned directly under the vertical segment or reinforcement of the frame member. 11

119 torflex installation Torflex Installation Chart racket Dimensions E Side Holes D Top Holes X Fender Clearance: allow 3" over the tire at full load. Torflex Axle Model Start Angle of Trailing Arm Mounting Hole to Wheel Center - Dimension "X" (Inches) 4 Down 3 Down. Down 10 Down 0 10 Up. Up No Load Full Load No Load Full Load No Load Full Load No Load Full Load No Load Full Load No Load Full Load No Load Full Load Mounting Hole Spacing (Inches) Dim "D" (Top) # (4" arm) # (" arm) #10 (" arm) #10L (" arm) #10F (" arm) #11 (" arm) #1 (" arm) #1T (" arm) #1V (" arm) #13 (" arm) #13T (" arm) Dim "E" (Side) Axle Alignment Dimensions To insure proper tracking, the axle must be placed on the frame perpendicular to the centerline of the vehicle. The accuracy must be within plus or minus one half degree. For multiple axle applications, each axle must be parallel with the others within one sixteenth of an inch when measured at the wheel centers. CAUTION: When laying out the position for the axle(s), measuring from the front cross member should only be done if the cross member has been checked for squareness to the frame centerline. Any error in the cross member will be transferred to the axle and can result in poor tracking and excessive tire wear. Figure 3 11

120 Dexter Axle Limited Warranty WHAT PRODUCTS ARE COVERED All Dexter Axle Company ( Dexter Axle ) trailer axles, suspensions, and brake control systems excluding Dexter 000 series Manufactured Housing Axles. LIMITED 1 YEAR WARRANTY As specified in Dexter Axle s current publication Operation Maintenance Service Manual, grease and oil seals FOR ALL PRODUCTS have a one (1) year limited warranty from the date of first sale of the trailer incorporating such components.except as to grease and oil seals, the following four other warranties are available. LIMITED YEAR WARRANTY Dexter Axle warrants to the original purchaser that its axles, suspension systems, and E/H hydraulic brake actuators shall be free from defects in material and workmanship for a period of two () years from the date of first sale of the trailer incorporating such components. Dexter Axle warrants to the original purchaser that its Genuine Replacement Parts shall be free from defects in material and workmanship for a period of two () years from the date parts were installed and serviced. LIMITED 3 YEAR WARRANTY FOR PARTICIPATING OEMS Dexter Axle warrants to the original purchaser of a trailer equipped with axle models D0, D100GD, D100HD, D10, or D10 and installed with properly matched Genuine Dexter Hanger and Attaching Parts Kits (HAP Kits) or Dexter Heavy Duty Suspension System (HDSS), that this combination of components shall be free from defects in material and workmanship for a period of three (3) years. The warranty period shall begin from the date of the original purchase of the trailer. LIMITED YEAR WARRANTY Dexter Axle warrants to the original purchaser that its Nev R-Lube bearings and the suspension components only, of its Torflex axles shall be free from defects in material and workmanship for a period of five () years from the date of first sale of the trailer incorporating such components. LIMITED YEAR WARRANTY Dexter Axle warrants to the original purchaser that its Predator Series electric brake controllers shall be free from defects in material and workmanship for a period of seven () years from the date of purchase. EXCLUSIVE REMEDY Dexter Axle will, at its option, repair or replace the affected components of any defective axle, repair or replace the entire defective axle, or refund the then-current list price of the axle. In all cases, a reasonable time period must be allowed for warranty repairs to be completed. Allowance will only be made for installation costs specifically approved by Dexter Axle. WHAT YOU MUST DO In order to make a claim under these warranties: 1. You must be the original purchaser of the vehicle in which the spring suspension axles or Torflex axles were originally installed.. You must promptly notify us within the warranty period of any defect, and provide us with the axle serial number and any substantiation which may include, but is not limited to, the return of part(s) that we may reasonably request. 3. The axles or suspensions must have been installed and maintained in accordance with good industry practice and any specific Dexter Axle recommendations, including those specified in Dexter Axle s current publication Operation Maintenance Service Manual. EXCLUSIONS These warranties do not extend to or do not cover defects caused by: 1. The connecting of brake wiring to the trailer wiring or trailer wiring to the towing vehicle wiring.. The attachment of the running gear to the frame. 3. Hub imbalance, or any damage caused thereby. 4. Parts not supplied by Dexter Axle.. Any damage whatever caused by or related to any alteration of the axle including welding supplemental brackets to the axle.. Use of an axle on a unit other than the unit to which it was originally mounted.. Normal wear and tear.. Alignment.. Improper installation. 10. Unreasonable use (including failure to provide reasonable and necessary maintenance as specified in Dexter Axle s current publication Operation Maintenance Service Manual including required maintenance after Prolonged Storage ). 11. Improper wheel nut torque. 1. Cosmetic finish or corrosion. LIMITATIONS 1. In all cases, Dexter Axle reserves the right to fully satisfy its obligations under the Limited Warranties by refunding the then-current list price of the defective axle (or, if the axle has been discontinued, of the most nearly comparable current product).. Dexter Axle reserves the right to furnish a substitute or replacement component or product in the event an axle or any component of the axle is discontinued or is otherwise unavailable. 3. These warranties are nontransferable. GENERAL THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXCEPT THAT OF TITLE, WHETHER WRITTEN, ORAL OR IMPLIED, IN FACT OR IN LAW (INCLUDING ANY WARRANTY OF MERCHANTAILITY OR FITNESS FOR A PARTICULAR PURPOSE). These warranties give you specific legal rights, and you may also have other rights which vary from state to state. DEXTER AXLE HEREY EXCLUDES INCIDENTAL AND CONSEQUENTIAL DAMAGES, INCLUDING LOSS OF TIME, INCONVENIENCE, LOSS OF USE, TOWING FEES, TELEPHONE CALLS OR COST OF MEALS, FOR ANY REACH OF ANY EXPRESS OR IMPLIED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. Inquiries regarding these warranties should be sent to: Dexter Axle Company P.O. ox 0 Elkhart, Indiana 41 Note: Current publication Operation Maintenance Service Manual can be found at LIMITED WARRANTY 11

121 Dexter Axle Video Gallery In keeping with our continual commitment to industry safety and the development of innovative products, please feel free to view our ongoing video gallery at or scan the following QR codes with your smart phone. We are confident these videos will help educate and promote the Dexter product line that you, as our customer, are investing in. earing Maintenance Genuine rakes E/H Actuator Installation E-Z Flex Suspension E-Z Lube System Genuine Replacement Parts Leaf Spring Axles Nev-R-Adjust rakes Removable Spindle Torflex Suspension Axles 10

122 Genuine Dexter axles and components are available nationwide from our plant locations listed below or through our network of distributors. Check our web site for the distributor nearest you. Visit us online at Dexter Axle 301 West Pearl Street Fremont, IN 43 Fax (0) Ph (0) Dexter Axle 00 South th Street Albion, IN 401 Fax (0) Ph (0) 3-1 Company Headquarters 00 Industrial Parkway East Elkhart, IN 41 Fax (4) - Ph (4) - Dexter Axle 00 Southeast th Street El Reno, OK 303 Fax (40) -0 Ph (40) -00 Dexter Axle 1 Perimeter Road Monticello, GA 3104 Fax (0) 4- Ph (0) 4-4 No part of this catalog may be reproduced without Dexter Axle s permission. All part numbers, dimensions and specifications in this catalog are subject to change without notice.

123 GEARED FOR INNOVATION SINCE Industrial Parkway East n Elkhart, IN 41 Phone: 4-- n Fax: 4-- ISO 001 Certified / Dexter Axle Company. LIT-1-00

600-8,000 LBS. CAPACITY

600-8,000 LBS. CAPACITY www.dexteraxle.com 00 -,000 LS. CAPACITY TRAILER RUNNING GEAR Introduction This information is intended as a guide for the proper specification and application of Dexter running gear, associated components

More information

General Applications. Axle Types. d30 & D35 leaf spring lbs. capacity 10 10F 10L Lbs. Capacity

General Applications. Axle Types. d30 & D35 leaf spring lbs. capacity 10 10F 10L Lbs. Capacity General Applications Axle Types 300-000 Lbs. Capacity Complete service manual Precision machined steel spindles and integral cast iron hub/drums Press-in wheel studs " x ¹ ₂" and " x ¹ ₄" CSA approved

More information

General Applications. Axle Types LBS. CAPACITY Lbs. Capacity

General Applications. Axle Types LBS. CAPACITY Lbs. Capacity General Applications Axle Types 600-1100 Lbs. Capacity Ideal application for light utility, for hauling personal watercraft and motorcycles Complete service manual Heavy duty 1¹ ₁₆" spindle design Precision

More information

General Applications. Axle Types. d60 & D70 leaf spring lbs. capacity Lbs. Capacity

General Applications. Axle Types. d60 & D70 leaf spring lbs. capacity Lbs. Capacity General Applications Axle Types 00-000 Lbs. Capacity Complete service manual Precision machined, forged steel spindles Precision machined integral cast iron hub/drums -bolt and bolt (UTG) hubs available

More information

General Applications. Axle Types D44, D52 & D60 LEAF SPRING LBS. CAPACITY Lbs. Capacity

General Applications. Axle Types D44, D52 & D60 LEAF SPRING LBS. CAPACITY Lbs. Capacity General Applications 400-000 LS. CAPACITY 40 Axle Types 400-000 Lbs. Capacity Complete service manual Precision machined steel spindles and integral cast iron hub/drums Press-in wheel studs 0" x ¼" CSA

More information

General Applications. Axle Types. d20 leaf spring lbs. capacity Lbs. Capacity

General Applications. Axle Types. d20 leaf spring lbs. capacity Lbs. Capacity General Applications Axle Types 1000-2200 Lbs. apacity omplete service manual eavy duty 1¹ ₁₆" spindle design Precision machined steel spindles and integral cast iron hub/drums SA approved 7" x 1¹ ₄" electric

More information

General Applications. Axle Types D20 LEAF SPRING LBS. CAPACITY Lbs. Capacity

General Applications. Axle Types D20 LEAF SPRING LBS. CAPACITY Lbs. Capacity General Applications Axle Types 1000-2200 Lbs. apacity omplete service manual eavy duty 1¹ ₁₆" spindle design Precision machined steel spindles and integral cast iron hub/drums SA approved 7" x 1¹ ₄" electric

More information

General Applications. Axle Types D20 LEAF SPRING LBS. CAPACITY Lbs. Capacity

General Applications. Axle Types D20 LEAF SPRING LBS. CAPACITY Lbs. Capacity General Applications Axle Types 1000-2200 Lbs. apacity omplete service manual eavy duty 1¹ ₁₆" spindle design Precision machined steel spindles and integral cast iron hub/drums SA approved 7" x 1¹ ₄" electric

More information

General Applications. Axle Types. D44, D52 & D60 leaf spring lbs. capacity Lbs. Capacity

General Applications. Axle Types. D44, D52 & D60 leaf spring lbs. capacity Lbs. Capacity General Applications Axle Types 300-000 Lbs. apacity omplete service manual Precision machined steel spindles and integral cast iron hub/drums Press-in wheel studs 0" x ¼" SA approved electric brakes "

More information

General Applications. Axle Types. d72 leaf spring lbs. capacity Lbs. Capacity 12V

General Applications. Axle Types. d72 leaf spring lbs. capacity Lbs. Capacity 12V General Applications Axle Types 7200 Lbs. apacity omplete service manual Precision machined steel spindles and integral cast iron hub/drums Finned brake drums for better heat dissipation Press-in wheel

More information

2,000 LB. CAPACITY S-20 - BTR HUB GROUP

2,000 LB. CAPACITY S-20 - BTR HUB GROUP 2,000 LB. CAPACITY S-20 - BTR HUB GROUP STANDARD GREASE LUBE PARTS HUBS Item Part # Description Item Part # Description Bolt Circle 602 Bearing Kit - 1 Hub 25 8-441 Plain Hub - tapped 4 on 4.00 1 10-9

More information

AXLES TABLE OF CONTENTS

AXLES TABLE OF CONTENTS A1 AXLES TABLE OF CONTENTS Our typical axle part number is a seven digit number with the axle nomenclature definition comprised of several groups of digits representing available options on that part number.

More information

12¹ ₄" x 2¹ ₂" Electric Brake Cast Backing Plate

12¹ ₄ x 2¹ ₂ Electric Brake Cast Backing Plate ¹ ₄" x ¹ ₂" Electric Brake Cast Backing Plate 00 lbs. capacity xecast_-0 CSA approved at 00#/. SLR 0 Electric Brake 0 K--00 LH Complete Brake Assembly (shown) 0 K--00 RH Complete Brake Assembly K--00 LH

More information

Sudden Stop Ahead! Is Your Trailer Equipped with Nev-R-Adjust Brakes?

Sudden Stop Ahead! Is Your Trailer Equipped with Nev-R-Adjust Brakes? www.dexteraxle.com Sudden Stop Ahead! Is Your Trailer Equipped with Nev-R-Adjust Brakes? Road hazards appear suddenly without warning. With a trailer behind you there s no time to second guess your ability

More information

9,000-15,000 lbs. Capacity

9,000-15,000 lbs. Capacity HEAVY DUTY UTILITY AXLES 9,000-5,000 lbs. Capacity www.dexteraxle.com Introduction This information is intended as a guide for the proper specification and application of Dexter Axle running gear, associated

More information

9,000-15,000 LBS. CAPACITY

9,000-15,000 LBS. CAPACITY www.dexteraxle.com 9,000-5,000 LBS. CAPACITY HEAVY DUTY UTILITY AXLES Introduction This information is intended as a guide for the proper specification and application of Dexter Axle running gear, associated

More information

Parts & Service Manual

Parts & Service Manual New 2017 Edition Parts & Service Manual SK6, SK7, SK8, SK9 B6DOW, B9DOW (Tridem) B8 & B9DOW (Tandem) ORDER GENUINE General Engines Co., Inc., 548 Swedesboro Ave., Mickleton, NJ 08056 Parts (800) 338-7088

More information

Y COMPLETE LIGHT TRAILER

Y COMPLETE LIGHT TRAILER Order NLINE CATALOG NUMBER 27 www.midwestwheel.com Order NLINE www.midwestwheel.com r u o Y COMPLETE LIGHT TRAILER e c r ou S Trailer Wheels & Tire Assemblies...2 Brake Controllers & Accessories...20 Torflex

More information

22,500-27,500 LBS. CAPACITY

22,500-27,500 LBS. CAPACITY www.dexteraxle.com 22,500-27,500 LBS. CAPACITY HEAVY DUTY D200 SERIES Introduction This information is intended as a guide for the proper specification and application of Dexter Axle running gear, associated

More information

DEXTER AXLE LBS. CAPACITY SUSPENSION SYSTEM

DEXTER AXLE LBS. CAPACITY SUSPENSION SYSTEM 5500-7000 LBS. CAPACITY AIRFLEX LIGHT L IGHT TRAILER SUSPENSION SYSTEM Suspension and axle come fully assembled for easy installation The suspension maintains a constant trailer floor height regardless

More information

700 2,200 lb. Spring Axles

700 2,200 lb. Spring Axles 700 2,200 lb. Spring Axles 700 2,200 SA Typical Industries & Applications include: Marine Trailers Personal Water Craft Boat Open Utility Trailers Landscape Sport Utility motorcycle, quad and tri wheel

More information

PREMIER, MARINE, & STANDARD

PREMIER, MARINE, & STANDARD INSTA LLATION INSTRUCTION AND SERVICE MANUAL I TITAN 12" x 2" BRAKES FREE BACKING. UNI-SERVO. DUO-SERVO PREMIER, MARINE, & STANDARD Limited Warranty TITAN Inc. ("TITAN') warrants its products to be free

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTION AND SERVICE MANUAL Actuator/Trailer Dealer - Please provide these instructions to the consumer. Consumer - Read and follow these instructions. Keep them with the trailer for future

More information

Axle Components. 12,000 lbs. Capacity

Axle Components. 12,000 lbs. Capacity 12,000 lbs. Heavy Duty Components 27-358 Unitized Oil Seal - disc or drum (Dimensions are 3.125 x 4.506 x.605) 2 010-056-00 27-342 3984 Inner Bearing (Inside diameter 2.625 ) 3 031-020-02 27-343 3920 Inner

More information

FOR LIGHT AND MEDIUM TRAILER AXLES

FOR LIGHT AND MEDIUM TRAILER AXLES COPYRIGHT 2008 SIRCO INDUSTRIES, INC. CATALOG LMT-1 COMPONENT PARTS L MT FOR LIGHT AND MEDIUM TRAILER AXLES TABLE OF CONTENTS PAGE ATTACHING FASTENERS 24-26 ATTACHING PARTS KITS 27-28 BEARINGS.. 5-7 BRAKE

More information

TITAN 13 x 2½ BRAKES DUO-SERVO AND FREE BACKING

TITAN 13 x 2½ BRAKES DUO-SERVO AND FREE BACKING INSTALLATION INSTRUCTION AND SERVICE MANUAL Actuator/Trailer Dealer - Please provide these instructions to the consumer. Consumer - Read and follow these instructions. Keep them with the trailer for future

More information

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains Trailer Parts Brake Components Axle Components Suspensions Lights & Electrical Wheels & Tires Loading Ramps Couplers & Safety Chains Trailer Jacks Fenders Dump Trailer Parts Tilt SST Parts Decal Kits Brake

More information

Brakes & Running Gear

Brakes & Running Gear Brakes & Running Gear 2018 Brake Assemblies / Parts...1-8 Chrome Turndown... 9 1 517-278-8521 approducts.net AP 517.278.8521 Fax: 517.278.2457 www.approducts.net 200 Jay Street Coldwater, MI 49036 Nuts

More information

CATALOGUE INDEX. Profiles & Dimensions - Non Braked Profiles & Dimensions - Braked. Dimensions - Non Braked Dimensions - Braked

CATALOGUE INDEX. Profiles & Dimensions - Non Braked Profiles & Dimensions - Braked. Dimensions - Non Braked Dimensions - Braked Page: Warranty CATALOGUE INDEX 8 9 0 8 9 0 Australian Design Rules Calculating Pitch Circles Non Braked Hubs & Stubs Non Braked Hubs & Stubs Non Braked Hubs & Stubs Non Braked Hubs & Stubs Disc Braked

More information

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains Trailer Parts Brake Components Axle Components Suspensions Lights & Electrical Wheels & Tires Loading Ramps Couplers & Safety Chains Trailer Jacks Fenders Dump Trailer Parts Tilt SST Parts Decal Kits Brake

More information

1970 Trans-Am Mustang Front Suspension Instructions. Manual, Volume One, Chassis. Special instructions and precautions will be given

1970 Trans-Am Mustang Front Suspension Instructions. Manual, Volume One, Chassis. Special instructions and precautions will be given 1970 Trans-Am Mustang Front Suspension Instructions 1. This kit was designed to be used in conjunction with the Rear Suspension kit. 2. This conversion follows standard procedures as described in the 1970

More information

12-1/4 x 3-1/2 Electric Wheel Brake

12-1/4 x 3-1/2 Electric Wheel Brake 12-1/4 x 3-1/2 Electric Wheel Brake A-216 819-0244 Installation Instructions An Altra Industrial Motion Company Contents Dimensions.... 2 Technical Specifications.... 3 Installation Instructions General....

More information

INSTRUCTION MANUAL. with ILLUSTRATED PARTS LIST. for TRAILER AND ACCESSORIES. Part Number (10,000 Pound Capacity)

INSTRUCTION MANUAL. with ILLUSTRATED PARTS LIST. for TRAILER AND ACCESSORIES. Part Number (10,000 Pound Capacity) TO-37 0079 0884 07586 INSTRUCTION MANUAL with ILLUSTRATED PARTS LIST for TRAILER AND ACCESSORIES Part Number 48388- (0,000 Pound Capacity) manufactured by HOBART BROTHERS COMPANY POWER SYSTEMS DIVISION

More information

This page intentionally left blank.

This page intentionally left blank. Owner's Manual for CZ PoleTrailers CZ Engineering, Inc. 33863 Highway E Dixon, MO 65459 (573) 759-2144 www.cze.com This page intentionally left blank. Thank-you for purchasing a CZ trailer. Many man-hours

More information

Model ET 5000W Operation and Service Manual

Model ET 5000W Operation and Service Manual Model ET 5000W Operation and Service Manual Patented 5/16 BALL Load Capacity: 5000 lbs The ET 5000W ESCALATE TRAILER offers ground level roll-on loading and roll-off unloading of equipment with non-tilting

More information

TEREX Woodsman 730 BRUSH CHIPPER

TEREX Woodsman 730 BRUSH CHIPPER Woodsman 730 BRUSH CHIPPER Parts Manual Customer Dealer S/N Frame # Date Woodsman 150 Commerce Drive, Farwell MI 486 Phone: (800) 953-553 Fax: (989) 588-487 Flipper Discharge Chute Hand Crank Belt Shield

More information

HR24TS Rotary Rake. Serial Numbers and higher. Illustrated Parts Breakdown. Guards and Guard Arm, Front Hay Curtain Mount.

HR24TS Rotary Rake. Serial Numbers and higher. Illustrated Parts Breakdown. Guards and Guard Arm, Front Hay Curtain Mount. HRTS Rotary Rake Serial Numbers 00 and higher Illustrated Parts Breakdown Page Page Page Page Page Page Page Page Page Page 0 Page Page Page Page Page Page Page Page Page Page 0 Tongue Front Frame Guards

More information

Technical Support Line: (952) Hanover Ave. Lakeville, MN

Technical Support Line: (952) Hanover Ave. Lakeville, MN Technical Support Line: (952) 985-5675 Email: Sales@QA1.net 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net INSTALLATION INSTRUCTIONS QA1 1967-1979 Mopar A-Body Rear 6 link Conversion System QA1 p/n

More information

PARTS MAN UAL SDA-1200 STEER ABLE DRIVE AXLE SDA-1400 STEER ABLE DRIVE AXLE SDA-1600 STEER ABLE DRIVE AXLE

PARTS MAN UAL SDA-1200 STEER ABLE DRIVE AXLE SDA-1400 STEER ABLE DRIVE AXLE SDA-1600 STEER ABLE DRIVE AXLE PARTS MAN UAL SDA-1200 STEER ABLE DRIVE AXLE SDA-1400 STEER ABLE DRIVE AXLE SDA-1600 STEER ABLE DRIVE AXLE WITH EX TENDED SERV ICE BRAKES AND ABS PRO VI SIONS Fabco Automotive Corporation, Livermore, CA

More information

Packaged Parts Overview

Packaged Parts Overview Overview The Nuera product line features the same parts used to build and maintain the highest quality and hardest working trailers in the industry. Manufacturer-grade repair parts and accessories, designed

More information

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL

More information

TITAN MODEL 6 SURG-O-MATIC ACTUATOR FOR TRAILER BRAKES

TITAN MODEL 6 SURG-O-MATIC ACTUATOR FOR TRAILER BRAKES INSTALLATION INSTRUCTION AND SERVICE MANUAL Actuator/Trailer Dealer - Please provide these instructions to the consumer. Consumer - Read and follow these instructions. Keep them with the trailer for future

More information

Installation Instructions and Service Manual

Installation Instructions and Service Manual Installation Instructions and Service Manual Model 80 Actuator* for Trailer Brakes 8,00 lbs Capacity Drum Brake Ready Disc Brake Ready US Patents: 6,37,2 and 8,342,9 *Model 80 - Manufactured after March

More information

Axle Attaching Parts. 29 years. Round Axle U-bolt Kits. Square Axle U-bolt Kits. Spring Seats. Heavy Duty Axle U-bolt Kits. Hardware for 1¾" Spring

Axle Attaching Parts. 29 years. Round Axle U-bolt Kits. Square Axle U-bolt Kits. Spring Seats. Heavy Duty Axle U-bolt Kits. Hardware for 1¾ Spring 29 years Axle Attaching Parts Round Axle U-bolt Kits Square Axle U-bolt Kits Includes 4 U-bolts, 8 Hex nuts, & 2 Tie plates ITEM# Axle Diameter Threads Spring width Fits Most... Price TAP175 1¾" 3 /8"

More information

UFP PRODUCTS. Unique Functional Products. 1. Actuator. 2. Couplers. 3. Stainless Steel Bearing Protectors, Buddy Brake

UFP PRODUCTS. Unique Functional Products. 1. Actuator. 2. Couplers. 3. Stainless Steel Bearing Protectors, Buddy Brake 1. Actuator 2. Couplers 3. Stainless Steel Bearing Protectors, Buddy Brake 4. Wheel Bearing Kits, Grease Seals 5. Spindo Seal Kits 6. Trailer Buddy Products 7. Hubs & Hub/Drums 8. Disc Brakes 9. Springs

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY TRUTRACK TRUNNION BAR WEIGHT DISTRIBUTION SYSTEM MAINTENANCE Keep the socket-mounted ends of the

More information

Heavy Duty Front-Drive Steer Axles MX-140 and MX-160 Series

Heavy Duty Front-Drive Steer Axles MX-140 and MX-160 Series Revised 11/2009 Heavy Duty Front-Drive Steer Axles MX-140 and MX-160 Series Catalog PB-0349 Strength Power Speed Agility MERITOR PARTS. RIGHT FROM THE START. TABLE OF CONTENTS MX-17/19/21-140 and MX-21/23-160

More information

Disc Brake & Components

Disc Brake & Components Disc Brake & Components DISC BRAKES Disc Brake Kits ( * All Silver Cadmium Kits are available with either Silver Cadmium or Stainless Steel Calipers.) Capacity Description CSA Certified 1,750 lbs. 3,000

More information

STANDARD DANA REAR ELECTRIC AXLE & BRAKES

STANDARD DANA REAR ELECTRIC AXLE & BRAKES 37 30 29 31 33 34 36 4 5 6 3 7 9 5 4 8 39 8 4 5 9 21 25 27 23 1 24 21 20 22 30 28 23 26 22 10 12 11 11 13 14 13 1 2 1 15 37 33 31 2 16 34 35 17 36 38 18 19 (10x) 26m 50 62 63 SHOE ID: INKED ID 4070FF 55

More information

Model 80 & 80E Actuator* for Trailer Brakes 8000 lbs Capacity Part #47206/ Drum Brake Ready Part #47208/ Disc Brake Ready

Model 80 & 80E Actuator* for Trailer Brakes 8000 lbs Capacity Part #47206/ Drum Brake Ready Part #47208/ Disc Brake Ready Installation Instructions and Service Manual For Serial Numbers 6020 and above. Model 80 & 80E Actuator* for Trailer Brakes 8000 lbs Capacity Part #47206/47207 - Drum Brake Ready Part #47208/47209 - Disc

More information

Spohn Performance, Inc. 494 E Lincoln Ave Myerstown, PA

Spohn Performance, Inc. 494 E Lincoln Ave Myerstown, PA Spohn Performance, Inc. 494 E Lincoln Ave Myerstown, PA 17067 1-888-365-6064 www.spohn.net Part# D94-02-TB-DS Adjustable Front Track Bar Dodge Ram 4x4 with 0-4" Lift 1994-2001 1500 & 1994-2002 2500 & 3500

More information

Drive End Bracket & Bearing. Drive End Bracket. Tandem Axle # #865733

Drive End Bracket & Bearing. Drive End Bracket. Tandem Axle # #865733 Drive End Bracket & Bearing #865089 1 06409700 1" Lock Collar 2 865733 Drive Bracket w/ Bearing 3 310037 End Drive Shaft Drive End Bracket #865733 1 03003100 Bearing 1" w/snap Ring 2 957795 Drive End Bracket

More information

What should be standard on today s trailer axle? Rustinhibitive surfaces? Waterproof electric connections?

What should be standard on today s trailer axle? Rustinhibitive surfaces? Waterproof electric connections? TRAILER AXLES RETHINK STANDARD IN TODAY S TRAILER INDUSTRY What should be standard on today s trailer axle? Rustinhibitive surfaces? Waterproof electric connections? Automotive-strength axle tubing? Believe

More information

LIMITED WARRANTY DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES

LIMITED WARRANTY DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES Published 08/15 LIMITED WARRANTY Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material

More information

OWNER S / OPERATOR S 1

OWNER S / OPERATOR S 1 OWNER S / OPERATOR S 1 DURALITE TRAILERS, LLC Duralite Aluminum Livestock Trailer Introduction To our customer: This manual has been prepared to help you operate and maintain your new Duralite Trailer

More information

Axle Components. Demand the original. Axle Components Driveshaft Components Repair Kits

Axle Components. Demand the original. Axle Components Driveshaft Components Repair Kits Axle Components Driveshaft Components Repair Kits Axle Components OE Quality Driveline Components Designed for Chrysler RAM Products www.demand.com Axle Components Driveshaft Components Repair Kits Only

More information

OWNER S GUIDE 8A DURALIFT II 13,200 LB. CAPACITY. Link Mfg. Ltd th St. N.E. Sioux Center, IA USA

OWNER S GUIDE 8A DURALIFT II 13,200 LB. CAPACITY. Link Mfg. Ltd th St. N.E. Sioux Center, IA USA OWNER S GUIDE 8A000715 DURALIFT II 13,200 LB. CAPACITY Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 www.linkmfg.com QUESTIONS? CALL CUSTOMER SERVICE 1-800-222-6283 DEALER / INSTALLER:

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill Short & Long Bed All Megacabs 9464/9474 HIDE-A-GOOSE HITCH INSTALLATION WARNING: Under no circumstances do we

More information

Product Catalogue. Version 8.0. Section. Arvin Meritor (ROR) Axle Components

Product Catalogue. Version 8.0. Section. Arvin Meritor (ROR) Axle Components Product Catalogue Section E Version 8.0 Arvin Meritor (ROR) Axle Components PRODUCT CATALOGUE 8.0 ArvinMeritor (ROR) Axle Type Capacity Wheel Fixing 300-0003-1D0F5 TM/T25010/ZMX 11,690 kg 10 stud M22 x

More information

TransLift TL 2550K Parts Manual

TransLift TL 2550K Parts Manual TransLift TL 2550K Parts Manual Tink, I nc. 2361 D urham Dayton H w y D urham, C A 95938 Toll Free 888-367-8465 Fax 530-895-0751 w w w.tink inc.co ṁ Table of Contents Full Assembly View... 2 Tank View...

More information

Installation Instructions and Service Manual

Installation Instructions and Service Manual Installation Instructions and Service Manual Model 66 Actuator* for Trailer Brakes 6600 lbs Capacity Part #47210/86167 - Drum Brake Ready Part #47211/86165 - Disc Brake Ready *US Patent No. 6,375,211 MODEL

More information

INSTALLATION, INSTRUCTION AND SERVICE MANUAL

INSTALLATION, INSTRUCTION AND SERVICE MANUAL INSTALLATION, INSTRUCTION AND SERVICE MANUAL Actuator/Brake/Trailer Dealer Please provide to consumer. Consumer Read and follow instructions. Keep with trailer for reference. Page 1 of 7 1. Introduction...

More information

Model 66/660* Actuator for Trailer Brakes 6,600 lbs Capacity Drum Brake Ready or Disc Brake Ready US Patent No. 6,375,211

Model 66/660* Actuator for Trailer Brakes 6,600 lbs Capacity Drum Brake Ready or Disc Brake Ready US Patent No. 6,375,211 Installation Instructions and Service Manual Model 66/660* Actuator for Trailer Brakes 6,600 lbs Capacity Drum Brake Ready or Disc Brake Ready US Patent No. 6,375,211 *Model 660 - Manufactured after March

More information

ISO 9001:2015 Certified 2900 Industrial Parkway East n Elkhart, IN Phone: n Fax:

ISO 9001:2015 Certified 2900 Industrial Parkway East n Elkhart, IN Phone: n Fax: www.dexteraxle.com 2900 Industrial Parkway East n Elkhart, IN 46516 Phone: 574-295-7888 n Fax: 574-295-8666 ISO 9001:2015 Certified 06/17 1997-2017 Dexter Axle Company. LIT-008-00 Introduction This information

More information

PARTS MANUAL THIS PAGE INTENTIONALLY LEFT BLANK. Ag-Bag International, Ltd. G7000 June Appendix A

PARTS MANUAL THIS PAGE INTENTIONALLY LEFT BLANK. Ag-Bag International, Ltd. G7000 June Appendix A The parts manual is organized into groups, it is designed to make the locating of parts easier. The exploded drawings also show assembly paths. All parts listed are available from your authorized Ag-Bag

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers recommended vehicle

More information

Replacement Parts, Service Manual and Operating Instructions

Replacement Parts, Service Manual and Operating Instructions Replacement Parts, Service Manual and Operating Instructions This manual covers the following models: BE-3.5 BE-5A BE-5 BE-6 BE-7 BE-5BL BE-6BL B-3.5P B-5P B-5 B-6B B-7 B-8 B-7B B-9B BE-5P BE-6P B-8PRS

More information

Installation Instructions

Installation Instructions Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 8mm, 13mm, 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw, File WARNING: Under no circumstances do we recommend

More information

HENRY & WRIGHT CORPORATION. Leading Manufacturer of Utility Trailers and Related Capital Equipment.

HENRY & WRIGHT CORPORATION. Leading Manufacturer of Utility Trailers and Related Capital Equipment. HENRY & WRIGHT CORPORATION Leading Manufacturer of Utility Trailers and Related Capital Equipment. 739 East 140 th Street Cleveland, Ohio 44110 Phone 216-851-3750 Fax 216-851-3970 utilitytrailers@henrywright.com

More information

TT4100 Rotary Tedder

TT4100 Rotary Tedder TT0 Rotary Tedder Serial numbers 0 and higher Illustrated Parts Breakdown Page Page Tongue Assembly S/N - Tongue Assembly S/N to Page Page Page Page Page Tongue Assembly S/N to Tongue Assembly S/N + Main

More information

ALUMINUM & STEEL CAR CARRIERS

ALUMINUM & STEEL CAR CARRIERS OWNER'S MANUAL ALUMINUM & STEEL CAR CARRIERS INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice All ratings specified are based on structural

More information

Installation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab

Installation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab GOOSENECK MOUNTING KIT Equipment Required: Fastener Kit: F Wrenches: 3/4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers

More information

SuperTrac. Axle. Service & Maintenance. Manual

SuperTrac. Axle. Service & Maintenance. Manual SuperTrac Axle Service & Maintenance Manual Table of Contents Page Exploded Views Section 1: General Information General Warnings Description of Axle Models Identifications Section 2: Installation Axle

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers

More information

Spring Axle Owner s Manual

Spring Axle Owner s Manual Spring Axle Owner s Manual Spring/Hub Axles for Marine and Utility Trailers Table of Contents Page Slipper Springs 2 Double Eye Springs 3 Inspecting Springs 4 Replacing Springs 5 Tire Tread Wear 6-7 Super

More information

Detroit Speed, Inc. Detroit Speed Control Arm and Spindle Kit A-Body P/N: &

Detroit Speed, Inc. Detroit Speed Control Arm and Spindle Kit A-Body P/N: & Detroit Speed, Inc. Detroit Speed Control Arm and Spindle Kit 1964-72 A-Body P/N: 030104 & 030105 The Detroit Speed A-Body front suspension kit is a bolt-on package that addresses the shortcomings of the

More information

FERTILIZER ELEVATOR SERIAL #

FERTILIZER ELEVATOR SERIAL # FERTILIZER ELEVATOR SERIAL # TABLE OF CONTENTS SAFETY FIRST... IMPORTANT ORDERING INFORMATION... FERTILIZER ELEVATOR BREAKDOWN... LOWER SECTION... '-" & '-" HITCH ASSEMBLY... TRANSITION SECTION... DRIVE

More information

Brake Kit Turf Sweeper

Brake Kit Turf Sweeper Form Number 3352-712 Brake Kit Turf Sweeper Model No. 07086 Parts Catalog Ordering Replacement Parts To order replacement parts, please supply the part number, the quantity, and the description of each

More information

STOP. with confidence!

STOP. with confidence! STOP with confidence! It is with great pleasure we introduce to you the Quality Trailer Products High-Performance Electric Brake assembly. With years of research and experience behind the development,

More information

HR930 Rotary Rake. Illustrated Parts Breakdown. Tongue & Main Frame. Gearbox & Tine Arm

HR930 Rotary Rake. Illustrated Parts Breakdown. Tongue & Main Frame. Gearbox & Tine Arm HR0 Rotary Rake Illustrated Parts Breakdown Page Page Page Page Page Page Tongue & Main Frame Guards Gearbox & Tine Arm Axle Assembly Rotary Gearbox PTO Shaft 0//0 Tongue & Main Frame 0 0 0 0 Ref# Description

More information

JK 8 Lug Front Locking Hub Conversion Kit

JK 8 Lug Front Locking Hub Conversion Kit JK 8 Lug Front Locking Hub Conversion Kit Kit #3034411 w/ Performance Rotors Kit #3034410 w/ Performance Slotted Rotors Kit #3034412 w/ Big Brake Kit Kit #3034413 w/ Big Brake Kit and Slotted Rotors Important

More information

ASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH

ASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH ASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH DEALER/INSTALLER: (1) Provide this Manual to end user. (2) Physically demonstrate procedures in this Manual to end user. (3) Have end user

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 15/16, 15/16 Crowfoot Adaptor Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw Optional, Raise Bed: 18mm socket, 15 extension As an option you can loosen

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16, 10mm, 18mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw 9465/9475 HIDE-A-GOOSE HITCH INSTALLATION All Fasteners Typical, Both Sides WARNING:

More information

MEX (55) QRO (442) Web Controls

MEX (55) QRO (442) Web Controls Web Controls SINGLE AND DUAL ROTOR TENSION CONTROL BRAKES MODELS:,,,, AND INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS Read this manual carefully, making full use of its explanations and instructions.

More information

4050A. Tire Changer. Parts Identification. For servicing single piece automotive and most light truck tire/wheel assemblies

4050A. Tire Changer. Parts Identification. For servicing single piece automotive and most light truck tire/wheel assemblies 4050A Tire Changer For servicing single piece automotive and most light truck tire/wheel assemblies Parts Identification READ these instructions before placing unit in service KEEP these and other materials

More information

Stellar 4 Clutch Manual

Stellar 4 Clutch Manual INSTRUCTIONS Stellar 4 Clutch Manual Thank you for choosing Tomar products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and

More information

Brake Actuation Systems. Brake BREAKAWAY KITS HYDRAULIC SURGE COUPLER

Brake Actuation Systems. Brake BREAKAWAY KITS HYDRAULIC SURGE COUPLER Systems BREAKAWAY KITS 20-236-7 Dexter s 9 amp breakaway kit features a rechargecable, sealed 34-285-00 maintenance-free battery and charger, for double free towing. The kit is compact in design and exceeds

More information

Product Catalogue. Version 8.0. Section. FUWA Axle Components

Product Catalogue. Version 8.0. Section. FUWA Axle Components Product Catalogue Section E Version 8.0 FUWA Section E Fuwa - Cam and Brake Assembly E:48 PRODUCT CATALOGUE 8.0 Fuwa - Cam and Brake Assembly Part List - 6 axle tube (square) - 5 axle tube (round) TL-11-427-800045

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 15/16, 10 mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw 9464/9474 HIDE-A-GOOSE HITCH INSTALLATION All Fasteners Typical, Both Sides WARNING: Under

More information

Part s Catalog. GT2100 Garden Tractor. Model No. 14AP80RP744. Original Instructions (EN) (01/31/06)

Part s Catalog. GT2100 Garden Tractor. Model No. 14AP80RP744. Original Instructions (EN) (01/31/06) Part s Catalog GT0 Garden Tractor Model No. AP0RP Original Instructions (EN) -0 (0//0) Model P0RP -0-00 Turf Tire, x. x -0-00 Rim,.0 x.0-00 Lug Nut, /- -00A-0 Wheel Assembly, x. x -00-00 Rim Assembly,.0

More information

MODEL EF Full Circle Tire Spreader

MODEL EF Full Circle Tire Spreader MODEL EF Full Circle Tire Spreader Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV. 062917 P/N: 81-0050C CAUTION

More information

TT4101 Rotary Tedder

TT4101 Rotary Tedder TT Rotary Tedder 0//0 Illustrated Parts Breakdown Page Page Page Page Page Page Page Page Page Page Page Tongue Assembly S/N S/N - Tongue Assembly S/N + Main Frame S/N - Main Frame S/N to Main Frame S/N

More information

JOHN DEERE 9970 COTTON PICKERS

JOHN DEERE 9970 COTTON PICKERS PARTS CATALOG FOR Mud Hog System II Rear Wheel Drive FOR JOHN DEERE 9970 COTTON PICKERS Mud Hog Model Numbers Tread Center OEM Aftermarket JD40005 JD47655 82, 90, 94, 106 TUTHILL Drive Systems 9098 West

More information

ROTARY RAKE PARTS BOOK MODEL E

ROTARY RAKE PARTS BOOK MODEL E ROTARY RAKE PARTS BOOK MODEL 1150 17.00803E This parts book is furnished for your convenience only. All parts must be purchased through an authorized dealer. Call us for a dealer near you. Issue Date:

More information

ACTUATOR ASSEMBLY EXPLODED VIEW - ALL SERIAL NUMBERS

ACTUATOR ASSEMBLY EXPLODED VIEW - ALL SERIAL NUMBERS Distributed by Ergonomic Partners sales@ergonomicpartners.com 314-884-8884 www.ergonomicpartners.com ACTUATOR ASSEMBLY EXPLODED VIEW - ALL SERIAL NUMBERS 1 UNI-B8001677 RIGHT LINKAGE ASSEMBLY 1 2 UNI-B8001678

More information

AIRFLEX Light Trailer Suspension System

AIRFLEX Light Trailer Suspension System AIRFLEX Light Trailer Suspension System 00-7000 lbs. capacity Smooth Out the Roughest Roads Soft Ride New hybrid suspension combines air and rubber torsion for an excellent ride Independent Ride and stability

More information

Installation / Owners Manual

Installation / Owners Manual DEALER/INSTALLER: (1) Provide this Manual to end user END USER: Part Number: 94621 94622* *Packaged for Individual sale. (1) Read and follow this Manual for Reese Installation. (2) Save this Manual for

More information

Part s Catalog. LX500 Lawn Tractor. Model No. 13AP60RP744. Original Instructions (EN) (01/31/06)

Part s Catalog. LX500 Lawn Tractor.   Model No. 13AP60RP744. Original Instructions (EN) (01/31/06) Part s Catalog For Parts Call 0-- or 0-- LX00 Lawn Tractor Model No. AP0RP Original Instructions (EN) -0 (0//0) For Parts Call 0-- or 0-- Model P0RP NUMBER --00 Turf Tire, 0 x 0.0 x -000-00 Rim,.0 x.0-0-0

More information

LSC 3052 PCW LANDSCAPE CART ASSEMBLY INSTRUCTIONS

LSC 3052 PCW LANDSCAPE CART ASSEMBLY INSTRUCTIONS VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665 7586 or Toll Free (800) 348 0868 Fax: (260) 665 339 www.vestilmfg.com e mail: sales@vestil.com LSC

More information