June COIL Handling & Processing Equipment

Transcription

1 June 2018 COIL Handling & Processing Equipment

2 MECON INDUSTRIES LTD Mecon is a leading manufacturer of coil processing and handling equipment, brake press tooling and special purpose machines. From our beginning in 1962, Mecon has provided rugged designs, quality workmanship, quality materials and reliable products. Our designers, welders, machinists millwrights, assemblers and inspectors, work together to create the best combination of function, price, quality and service. MECON INDUSTRIES LTD q In house engineering and design with licensed professional engineers q Fully equipped factory q Large assembly and testing area We take pride in offering the finest in equipment and workmanship. FRONT COVER NO Marks Allowed Cut to Length Line Coil car, Uncoiler with Overarm, NO MARK threading table, Straightener with Shear, Pick and drop with NO MARK stacking system, Adjustable stacking table. Index: COIL LINE ARRANGEMENTS THE MATERIAL TYPES OF SYSTEMS REEL SYSTEMS-SINGLE -DUAL CRADLE UNCOILER CRADLE STRAIGHTENER POWERED STRAIGHTENERS STRAIGHTENERS FOR HIGH STRENGTH STEEL THREADING SYSTEMS - OPTIONS ROLL FEEDS AND FEEDER-STRAIGHTENERS SIDE SHIFTING FEEDERS COIL HANDLING SYSTEMS SOLVING PROBLEMS OTHER PRODUCTS AND SERVICES OPTIONS INHOUSE MANUFACTURING LOOPS AND PITS MATERIAL PROPERTIES Copyright c Mecon Industries Page 1

3 COIL LINE ARRANGEMENTS SUGGESTED SYSTEM ARRANGEMENTS Mecon Industries Limited manufactures a variety of coil processing systems. Many factors should be considered when determining the optimum arrangement. q Budget q Coil Weight q Plant space available q Crane capacity q Lift truck capacity q Mark sensitivity q Material thickness q Material width q Material strength q Coil handling: loading and unloading partial coils, or run full coils to end q Coil inside diameter q Coil outside diameter q Production required: feed length, speed, feed angle, feed time q Duty Cycle: hours per day / days per year q Process type: progressive stamping, blanking, blank and transfer, cut to length, pre-punch, etc. LINE 1 BACK TENSION UNCOILER POWERED STRAIGHTENER PRESS-MOUNTED SERVO ROLL FEED LINE 2 MOTORIZED UNCOILER POWERED STRAIGHTENER SERVO ROLL FEEDER LINE 3 POWERED TRAVEL & LIFT COIL CAR BACK TENSION UNCOILER (WITH JOG MOTOR) THREADING STAND POWERED STRAIGHTENER SERVO ROLL FEEDER LINE 4 MOTORIZED UNCOILER HOLD-DOWN ARM SERVO FEEDER-STRAIGHTENER LINE 5 MOTORIZED UNCOILER UNDER PADDLE LOOP CONTROL SERVO FEEDER-STRAIGHTENER LINE 6 POWERED TRAVEL & LIFT COIL CAR WITH IDLE ROLLS MOTORIZED UNCOILER WITH LOOP CONTROL OVERARM WITH COIL GUARD SERVO FEEDER-STRAIGHTENER (WITH THREADING OPTION) LINE 7 POWERED TRAVEL & LIFT COIL CAR WITH IDLE ROLLS BACK TENSION UNCOILER (WITH JOG MOTOR & SIDE SHIFT) POLL-OFF PINCH STAND WITH OVER-ARM COIL GUARD FEEDER-STRAIGHTENER (WITH THREADING OPTION) LINE 8 COIL CRADLE COIL THREADING AND PREBENDER SERVO FEEDER STRAIGHTENER LINE 9 COIL STORAGE RAMP COIL CRADLE STRAIGHTENER SERVO ROLL FEEDER LINE 10 COIL CRADLE STRAIGHTENER (WITH THREADING OPTION) FLOOR-MOUNTED SERVO ROLL FEED COIL LINE ARRANGEMENTS LINE 11 SERVODRIVEN COIL-CRADLE-STRAIGHTENER-FEEDER HEAVY DUTY DEKINKER AND COIL THREADER WITH COIL STAGING RAMP SIDE SHIFT BASE Page 2

4 The Material It helps to understand the nature of the input material and how it got that way. Most strip or coiled material begins its final processing phase as a slab. The slab was reduced to the final gauge by rolling, then wound into a large coil. It has grown greatly in length and nominally in width. High internal stresses in the material are often created during the rolling process. The internal stresses often vary from the outer wraps to the inner wraps and from the center to the edges. The strip is unwound, slit to width and rewound. Center slit material often yields the best material, edge cuts often yield the worst. When the internal stresses are not balanced, the slit material will have camber. The greater the stress imbalance, the worse the camber. In some instances, additional processing will be necessary to balance the internal stresses and eliminate camber. Poor material is a leading cause of difficulty in tracking the strip through the entire system. Camber problems will consume your profits! The Material To avoid many coil-handling problems, insist on quality material, reject that which does not meet your standards, and use the proper uncoiling system. Productivity Selecting the proper options for your system will provide big paybacks in productivity gains. q Eliminate waiting time for overhead cranes or lift trucks by installing coil cars and coil storage ramps. Coils can be staged when convenient and are ready when the system needs them q Reduce handling time and increase safety with coil clamping arms and threading equipment q Use dual spindle uncoilers when feeding high demand systems like rolling mills or systems using partial coils q Use variable speed loop controls to smooth the uncoiling - straightening process, maintain proper loop geometry, and deliver more consistent material to the feeder q Use a side shift base on the uncoiler to allow easy coil alignment and adapting for camber during processing q Purchase the best material possible to ensure good quality, consistent parts Page 3

5 TYPES OF UNCOILERS WHICH UNCOILING METHOD IS BEST?... REEL OR CRADLE Both types of uncoiler have advantages and limitations. In general, a reel works best with thin to medium-thick material, the cradle works well with thicker materials. Consider the Reel if: q Material is sometimes thinner than q Rewinding full or partial coils q Precise tension control is necessary q Material marking is critical q Straightener is pulling the material off the coil q Powered uncoiling of materials thinner than 0.150" Consider the Cradle if: q Material is always thicker than q Rewinding is not important q Tension control is not important q Material marking is not critical q Powered uncoiling of materials thicker than TYPES OF UNCOILERS Page 4

6 REELS - SINGLE and DUAL SPINDLE UNCOILER REELS - Single and Dual Spindle The reel is used in most uncoiling, recoiling applications. It can be fitted with a variety of drive and braking systems, combined with coil cars. pinch rolls, power straighteners, overarms, rolling mills or configured as a stand alone machine. Reels are the best choice for thin, prefinished and other mark sensitive materials. They support the coil on the inside diameter and thus avoid stock deformation problems. REELS - SINGLE and DUAL SPINDLE UNCOILER Advantages q Suited to wide ranges of material q Give precise control of the material q Can unwind or rewind q Available as single or dual spindle q Quick coil change times using dual spindle versions q Available with various drive and brake systems q Prevents damage to soft, prefinished, and mark sensitive materials Page 5

7 REEL and CRADLE UNCOILERS q Light to heavy duty braking systems q Hydraulic or mechanical mandrel expansion q Outboard spindle supports for heavy, wide coils with, small inside diameters q Traveling or fixed position q Coil clamping arms with idle or driven wheels q Combination with coil car, or coil elevator q Quick release coil keepers q Laser loop controls REEL UNCOILER OPTIONS MODELS D - Dual spindle B - Overrun brake BT - Back tension brake BTJ - Back tension brake with jog motor for threading M - Motorized CR -Cradle style uncoiler Coil REEL SERIES CAPACITY (LBS.) Width 1,500 2,500 4,000 6,000 10,000 15,000 20,000 25,000 30,000 40,000 50,000 60,000 16" STD 18" O STD STD 24" O O O STD STD 30" N O O O O STD 36" N N N O O O STD STD STD STD 48" N N N O O O O O O O STD STD 60" N N N N N D D D D O O O 72" N N N N N D D D D D D D N = not available, O = optional, D=derate to next lower weight Easy, fast loading of coils is the single most important benefit offered by cradle-type uncoilers. Page 6 CRADLE UNCOILER q Rugged heavy duty steel construction q Self centering coil keeper plates q Lifting points for crane q Forklift truck lifting tubes q Motor driven cradle rolls q All rolls hardened to 55RC q All lubrication points marked and easily accessible q Capacities from to mild steel, 12 to 72 (larger sizes call for quote) q Standard payout speed of 0 to 80 fpm. Rewind of unused material may be difficult q Not recommended for use with thin, prefinished, or mark sensitive REEL and CRADLE UNCOILERS

8 CRADLE-STRAIGHTENERS The combined cradle-straightener offers easy handling of medium to thick materials, great use of space. and a simple design. Combining the straightening and uncoiling function in one machine simplifies the control and the drive system, reduces the number of components and is less costly than a combination reel and power straightener. The material flows from the coil, through the straightener and into the loop, The straightener is inclined downward to shorten the loop distance and improve material flow. PROS: q Simple control and drive system q Confinement of coil helps control of thick materials q Easy and safe coil loading CONS: q Rewinding of unused material may be difficult q Not recommended for use with thin, prefinished, or mark sensitive materials CRADLE-STRAIGHTENERS q Rugged heavy duty steel construction q Self centering coil keeper plates q Lifting points for crane q Forklift truck lifting tubes q Driven cradle and straightener rolls q All rolls hardened to 55 RC Features of Mecon Cradle-Straighteners: q All lubrication points marked and easily accessible q Capacities from.060" to.375" mild steel. 12" to 72 q Standard payout speed of 0 to 80 fpm q Digital indicators show straightener roll position q Standard straightener head with entry and exit pinch rolls, and 7 straightening rolls q Other sizes available to suite application Page 7

9 CRADLE-STRAIGHTENERS OPTIONS: q Combine with coil staging ramp q Laser loop control q Automatic lubrication systems q Coil clamping and threading q End pivot threading tables q Drive Upgrades q Straightener Upgrades q 60 or 72" maximum coil outside diameter CRADLE-STRAIGHTENERS **Max thickness in steel, Yield Strength less than 30,000 psi Use maximum material thickness for guidance only. Provide Mecon with application data. Actual capacity is dependent on process requirements (speed, range of materials, material hardness, system response time, etc Upgraded drives, straightener support rolls and other features are available. Page 8

10 POWERED STRAIGHTENERS Power straighteners are selected on the basis of the material to be processed, The thickness, width, material type, hardness, and other factors. For most materials and flatness requirements, use straightener with five to seven rolls. For some materials, and high flatness requirements, more rolls may be necessary. POWERED STRAIGHTENERS Features of Mecon Cradle-Straighteners: q Smooth operation. no sudden stops and starts q Automatically match process demand q Rugged heavy duty steel construction. q Driven pinch and lower straightener rolls q All rolls hardened to 55 RC q Standard payout speed of 0 to 80 fpm q Entry side guide rolls q Entry and exit support rollers q Capacities in mild steel from.010" to.450", 12" to 72" wide q All lubrication points marked and easily accessible q Digital indicators show straightener roll position q Standard straightener head with entry and exit pinch rolls, and 7 straightening rolls q Lifting points for crane q Forklift truck lifting tubes Options: q Entry and exit threading systems q Laser loop control q Automatic lubrication systems q Drive upgrades q Straightener support rolls q 9, 11, or more straightener rolls q Power roll adjustment q Inclined or horizontal material flow Machine Roll MACHINE and MATERIAL WIDTH Diameter Thickness** str Call for capacity 3str str str str Use maximum material thickness, for guidance only. Provide Mecon with application data. Actual capacity is dependent on process requirements (speed, range of materials, material hardness, system response time. Etc.). Upgraded drives, straightener support rolls and other features are available. Page 9

11 STRAIGHTENERS FOR HIGH STRENGTH STEELS New Rules New Tools Stronger thinner materials are becoming more common. The stronger materials frequently may have more complex stress conditions such as: crossbow, twist, wrinkle edge and pocketing. The standard coil feed systems are designed to remove coilset that is curvature in the material from being wound into a coil. The presence of crossbow indicates that stresses also exist in the across the width direction. In order to remove these issues, the straightener must be constructed to allow deeper work roll settings. Solutions may involve: q More work rolls q Variable Geometry q Closer roll centers q Support rolls Consult Mecon Engineering for the best configuration for your material STRAIGHTENERS FOR HIGH STRENGTH STEELS Example Straightener with 11 work rolls for High Strength Steel Page 10

12 THREADING SYSTEMS-OPTIONS Mecon offers a variety of systems to make threading safer, easier and quicker. Coil overarms clamp the coil to prevent "clock springing" when the retaining bands are cut. Peelers extend out to the coil to direct the start of the material toward the straightener. Deflectors guide the material into the straightener pinch rolls. Prebenders flatten the leading edge of thicker materials to allow better flow into the straightener. Exit threading tables pivot up to span the space between the straightener and the feeder and direct the material into the feeder. THREADING SYSTEMS-OPTIONS Standard Arrangements: q Medium duty system includes straightener mounted overarm, peeler and deflector. q Heavy duty system includes straightener mounted overarm with power driven wheel, peeler, deflector, and prebender. q Consult Mecon when selecting a threading system. Threading Table extended to guide Material over the pit to feeder OPTIONS: COIL ELEVATORS, CARS AND STORAGE RAMPS Allows the material handler to load the next coil as the current coil is in process. The new coil is held in position and as soon as the current coil runs out, the new coil is ready for loading. Available in width capacities matching the uncoiler from 2,500 lbs to 60,000 lbs Page 11

13 ROLL FEEDS and FEEDER-STRAIGHTENERS ROLL FEEDS and FEEDER-STRAIGHTENERS Mecon feeders use Servo motors and controls, precision drive systems, and heavy-duty Components to provide quick, accurate indexing of material. They are designed to pull from an Accumulation loop (not directly off the coil), and accurately position the material each feed cycle. Fast, Flexible,Operation q The controls are located on a console or pedestal for convenient entry of job settings. Set up time is reduced to seconds, just enter the values using the keypad. q Very accurate roll positioning can be achieved with Mecon servo driven roll feeds. (The drives provide precise control of position, speed, acceleration, and deceleration.) q Diagnostic display of operating status and faults q Feed before press or press before feed modes q Both feed rolls are driven using a constant mesh 4 gear train, gears are hardened 4140 steel q Hardened vertical side guide rolls align the strip to the tooling q Entry ramp rolls support material to ensure smooth flow from loop into feeder ROLL FEEDS and FEEDER STRAIGHTENERS Optional Mountings include: q Press mounting q Floor base q Rolling base q Powered jack q Self centering guide rolls, Etc. Page 12

14 ROLL FEEDS and FEEDER-STRAIGHTENER ROLL FEEDS and FEEDER-STRAIGHTENERS Series F q Standalone Feeder q Suited to wide range of materials and process speeds q Highest output speeds q Full pilot release of pinch rolls q Dual air pressure pinch system allows gentle touch on sensitive materials to firm grip for difficult materials q Feed rolls are hardened, precision ground, surface treated and chrome coated for a hard, high friction surface giving excellent grip and long life q Rolls are supported by precision, permanently sealed and lubricated ball bearings Machine Roll MACHINE and MATERIAL WIDTH Diameter 12" 18" 24" 30" 36" 48" 60" 72" 250f 2.500" f-hd 2.500" f 3.250" f-hd 3.250" , f 4,000" f-hd 4,000" f-hdg 4.000" f 5.000" f 6.000" f 8.000" Call for capacity Max. Thickness at full width Series F-S q F series feeder with a 5 or 7 roll pull-thru straightener q Suited to materials needing limited correction q Lower capacity and performance than series FS q P225str pull-thru straightener for thin materials Max, thickness in steel, Yield Strength less than 30,000 psi. Use maximum material thickness for guidance. Provide Mecon engineering with application data. Actual capacity is dependent on process requirements (spm, feed length. range of materials) MACHINE and MATERIAL WIDTH Machine P225STR P3STR 12" 18" 24" 30" 36" 12" 18" 24" 30" 36" 48" 250f-hd-s f-s f-hd-s f-s f-hd-s f-hdg-s s Call for capacity Page 13

15 SERVO ROLL FEEDS and FEEDER-STRAIGHTENER Series FS and FSP q Combined feeder and straightener q Straightener rolls and entry pinch rolls are driven q 6 roll straightener with support rolls *** q Higher capacity than F-S q Better flatness than F-S ** *straightener support rolls on all machines except: 325fs series 400fs12 400fs18 400fs24 Series FSP q FS feeder-straightener with full pilot release of straightener q Same thru-put as FS series q Pilot release improves feeding performance and reduces die problems q Optional servo driven pilot release Machine Roll Diameter Mild steel-yield strength less than 30,000 psi min. Example 600FSP48 with Servo Pilot Release MACHINE and MATERIAL WIDTH Feed Stnr thick fs fs fs-hd fs fs-hd fs fs-hd SERVO ROLL FEEDS and FEEDER-STRAIGHTENERS ** Page 14

16 SIDE SHIFTING FEEDERS Side Shifting Feeders Mecon offers roll feeds with servo driven shift base to allow optimum use of material. The standard control has 3 pre-prograrnmed patterns. Shift and Feed distance are simply keyed in at the operator's console. Select the pattern, press start and the machine is ready to run. SIDE SHIFTING FEEDERS Pattern 1 Pattern 2 Pattern 3 1 X Center 1.87 X Center 2.74 X Center Distance Distance Distance Center Distance Center Distance Strip Width Feed Value Shift Value Material Use Material Scrap Pattern1 Pattern 2 Pattern 3 1 X C.D. 1 X C.D. 0 78% 22% 1.87 X C.D..5 X C.D..44 X C.D. 84% 16% 2.74 X C.D..5 X C.D..87 X C.D. 86% 14% Center Distance CL CL CL Page 15

17 COIL HANDLING SYSTEMS Coil car, Side shift uncoiler, Peeler-Deflector, Straightener, Threading table, Floor mount Feeder. COIL HANDLING SYSTEMS Combination Cradle-Straightener-Feeder model 200csfx42 Coil staging ramp, Cradle, Threading system, Feeder-Straightener with Servo pilot release, Worm screw jack lift systems Page 16

18 COIL HANDLING SYSTEMS Main features are: q Single operator q Easy to load q High capacity - high performance q Compact - save floor space q With Coil Roller keepers SPACE SAVER The choice when plant space is limited, Requires far less overall floor area than conventional systems. COIL HANDLING SYSTEMS Complete Press Feed System: Coil Car, Motorized Uncoiler with Over arm, Laser loop control, Threading system, Floor mount Servo Feeder-Straightener, Control console, Safety fencing Page 17

19 SOLVING PROBLEMS Mecon Industries is equipped to help solve your challenging production problems. Our objective is to design and build equipment which maximizes productivity, ensures operator safety, and improves return on investment. Reduced downtime for coil change overs may make the difference between profit and loss. Fast loading, easy operation make for a streamlined, safe and profitable operation. No space for side loading No space for traditional loop Top loading, space saver solution SOLVING PROBLEMS Cradle with Coil staging ramp for HSLA material 90KSI at 72 WIDE,.190 thick. 6STR72, 9 roll straightener with exit table. Page 18

20 OTHER PRODUCTS OTHER PRODUCTS Servo Feeder-Straightener with Servo Pilot release for HSLA 4 adjustable over 4 roll geometry with backup rolls to minimize roll deflection Servo Pilot release for low maintenance High performance No Mark Cut to Length system Coil Car, Motorized Uncoiler with Over arm, Laser loop control, Threading system, Floor mount Servo Feeder-Straightener, Shear with no mark glide and drop stacking system Page 19

21 OTHER PRODUCTS Mecon offers many other products and services. q Coil upenders q Tube Handling systems q Crop shears q Punching Systems q Edge conditioners q Cut to length systems q Special purpose machines q Brake press tooling q Fabrication & machining services q Machine rebuilding & updating 20,000lbs Pipe Uncoiler Straightener System OTHER PRODUCTS 400F18HDG Feeder system, 75 Ton press with 12 Punch locations Shear for.25 HSLA Steel Page 20

22 OTHER PRODUCTS High Speed C channel punching machine 3,000+ ft/hr process speed OTHER PRODUCTS Heavy, Bulky, Irregular Object Manipulators Multi degree of motion Load, Lift, Tilt, Rotate and Move Page 19

23 OPTIONS Upenders 6,000lbs to 60,000;bs Shears Overarms OPTIONS Coil cars 20 and 24 lift End Pivot Threading Table Multifunction pendant Stacking systems See all available options: Material guidance systems Page 20

24 IN-HOUSE WARRANTY MANUFACTURING Mecon has the facility, equipment and workforce capable of handling large or small projects. In-house design and manufacturing allows Mecon to maintain control of the production schedule and completion dates. Mecon manufacturing combines fabricating, conventional and CNC machining, grinding and material handling up to 15 tons. All design, cutting, machining, and assembly is done to Mecon's exacting standards. IN-HOUSE MANUFACTURING In-house Fabrication: Weld Shop In-house Assembly area Page 21

25 IN-HOUSE MANUFACTURING Machine designs are constantly reviewed to incorporate the best methods and technology. Modern electrical control systems. variable speed and servo systems are integrated with rugged mechanical components to achieve long service life and high uptime. Mecon's large assembly area allows setup and complete operational testing of the system. All machines are inspected and tested before being released to the customer. With a fully equipped factory and successful experience in many fields we are able to offer solid designs, and economical hard working equipment. Mecon offers a variety of services and materials for your metal handling needs: Engineering, General Machining, Fabrication, Brake Press Tooling, Coil Processing Machines, and Custom Build/Rebuild Machinery. IN-HOUSE MANUFACTURING Page 22

26 ACCUMULATION LOOPS AND PITS Most systems require an accumulation loop. The accumulation loop is used to allow the uncoiling process to payout at a nearly continuous rate while the feeding equipment stops and starts. Ideally the loop will accumulate at least 2 feed lengths of material. Thickness, material yield strength, and feed length are important factors to consider when determining loop geometry. The loop must store sufficient material to allow smooth operation. The material must not be curved smaller than the minimum bend radius to ensure that the proper loop shape is maintained and kinking does not occur. q Ramamp rolls should support the material as it enters and exits the loop. q The loop length should be 1000 to 1400 times the material thickness. ACCUMULATION LOOPS AND PITS Loop Height (H) Process Height Pit Depth A pit is recommended if the required LOOP HEIGHT, is greater than the process height MAXIMUM FEED LENGTH (INCHES) Loop Length (L) 1000 to 1400 x Thickness Max Feed Length Empty Full Accumulation Loop Height (H) MINIMUM LOOP HEIGHT (INCHES) 135" " 120" " " 105" " " 90" " " 75" " " 60" " " 45" " " 30" " " 15" " 120" 150" 180" 210" 240" 270" 90" 120" 150" 180" 210" 240" 270" LENGTH OF LOOP (L) LENGTH OF LOOP (L) Page 23

27 MATERIAL PROPERTIES STEEL COIL WEIGHT CALCULATOR coil weight LBS / INCH 72" Outside diameter of Coil 66" " " " " " " " " 20" 24" INSIDE DIAMETER OF COIL Typical Tensile Strengths Common Metals Steel Coil Weight Calculator Material weight factors Aluminum x 0.35 Brass x 1.08 Copper x 1.14 Stainless x 1.00 multiply CHART VALUE by COIL WIDTH eg: 714 lbs/in x 10" wide coil = 7,140 lbs Yield Strength Ultimate Yield Strength Density PSI Mpa PSI Mpa lb/in 3 g/cm 3 Aluminium alloy 6061-T6 35K K Aluminium alloy 2014-T6 60K K Brass 29K K Copper 99.9% Cu 10K 70 32K Cupronickel 10% Ni, 1.6% Fe, 1% Mn, balance Cu 19K K Steel, 1090 mild 36K K Steel, 2800 Maraging steel 380K K Steel, AerMet K K Steel, AISI 4130, water quenched 855 C 138K K Steel, API 5L X65 65K K Steel, high strength alloy ASTM A K K Steel, stainless AISI cold-rolled 75K K Steel, structural ASTM A36 steel 36K K-80K Tungsten 136K K MATERIAL PROPERTIES Page 24

28 WARRANTY WARRANTY Mecon Industries warrants to the purchaser, the design and manufacture of standard equipment for the following periods, from the date of delivery; q Frame and Chassis components, the sooner of 24 months or 4000 production hours. q Moving components produced by Mecon, the sooner of 12 months or 2000 production hours. q Electrical, hydraulic, or pneumatic components, the sooner of 12 months, or 2000 production hours. q Components not produced or modified by Mecon, per individual manufacturers' warranty. Mecon promises to repair or, at Mecon's option, replace any component which, during normal use, proves to be defective in material or workmanship during the warranty period. The original purchaser will be responsible for all shipping costs, and the cost of dismantling and reassembling the warranted equipment as necessary for the repair or replacement. This warranty shall not extend to any equipment which has been improperly installed, subjected to misuse, neglect, accidents, modified, or repaired by unauthorized personnel. This warranty is not transferable. In the case of equipment sold through a dealer the warranty is extended to the initial user only. EXCEPT AS EXPRESSLY PROVIDED HEREIN, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING A WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. In no event shall Mecon Industries Limited be liable for special, indirect, incidental or consequential damages, however arising. Page25

29 Mecon Industries Ltd is a leading designer and manufacturer of Coil Handling Equipment, Tooling for Press Brakes, and Custom equipment. With a wide range of experience in many fields, we are able to create cost effective designs and long lasting equipment. Mecon offers a variety of services (and materials) for your projects and manufacturing challenges: Engineering, Custom Build, General Machining, Custom Fabrication, Brake Press Tooling, Coil Handling Systems (Processing), and Rebuild of Machinery. Coil Handling - Press Brake Tools - Custom Equipment Call us today at +1 (416) to find out more information about Coil Handling, Press Brake tooling or Custom Equipment design.

30 runcoilers rcradle STRAIGHTENERS rservo ROLL FEEDS rhsla STRAIGHTENERS rcomplete PRESS FEED LINES rcustomized COMBINATIONS rcustom MACHINE DESIGN rin-house MANUFACTURING Mecon Industries Limited 17 Malley Road Scarborough, Ontario M1L 2E4 Canada Tel.: (416) Fax: (416) Website: