HERGOTT Julien & MOISY Alexandre EHRS modelling with GT-Suite European GT Conference 2015

Size: px
Start display at page:

Download "HERGOTT Julien & MOISY Alexandre EHRS modelling with GT-Suite European GT Conference 2015"

Transcription

1 HERGOTT Julien & MOISY Alexandre EHRS modelling with GT-Suite European GT Conference 2015

2 Reduce CO2 by more than 50% in Europe, USA and China between 2005 and 2025 Average CO2 emissions from new passenger cars g/km Mid term Longer term Long term 95? 89? 68-75? Time (year) USA CHN EUR Strong short-term and long-term pressure on CO 2 will create demand for fuel-saving technologies

3 While about one third of the fuel s energy is lost as heat through exhaust gas support the thermal system : Heat to Heat Fuel Power Friction reduction engine & gearbox Exhaust Heat Recovery Manifold (EHRM) Cabin heating in cold weather Mechanical Power Cooling heat Exhaust heat Exhaust Heat Recovery System (EHRS) generate on-board electricity: Heat to Power Seebeck effect Thermo-Electric Generation (TEG) Rankine cycle Exhaust Heat Power Generation (EHPG) Recovering Exhaust Heat to... * indicative values

4 Why EHRS improves fuel economy on an FHEV? On Hybrid vehicles, typical strategies will trigger Combustion engine start on : Wheel power demand Coolant temperature Typically 50 to 60 C Typical FHEV ICE Strategy Battery State of Charge 4

5 By improving engine warm-up on FHEVs, EHRS enables earlier and more frequently the pure Electric mode, thus improves significantly the fuel economy. Inputs WITHOUT EHRS Inputs WITH EHRS EV mode EV mode EV mode EV mode EV mode Coolant temperature C Coolant temperature C EHRS allows Coolant loop to reach temperature threshold quicker Combustion engine running time is decreased Fuel mass consumed is lowered 5

6 How to estimate EHRS Benefits on customer vehicles? Evaluate EHRS Design Performance Estimate Impact on vehicle Requirement Measured on Component bench Predicted using CFD Measured on roller bench on prototype Problem Complex Expensive Not flexible Solution Build 1D Model of EHRS component for EHRS Performance prediction Build 1D model of EHRS environnent on vehicle for Impact prediction 6

7 Overview of System model Inputs Input Engine Exhaust EHRS Outputs Driving conditions Coolant Temperature ICE Trigger strategy Combustion heat Cooling Recovered heat Ambient conditions Cabin Engine running duty cycle Heating demand Cabin heat EHRS Configuration Ambient losses Ambient Fuel economy Simplified thermal model to assess EHRS impact on vehicle thermal behavior and fuel economy 7

8 Generating Engine outputs by using 1D Engine model 1D Engine Model with Cylinder Twall Solver allows to use Vehicle Inputs to estimate Combustion to Cooling heat transfer Engine Fuel efficiency Exhaust Enthalpy Engine - Input Engine Model Output Vehicle data (SCx, Mass, Gear ratio) Speed vs. Time (NEDC, FTP, Steady ) Hybrid strategy Heat rejected Power Air Mass flow Fuel Mass flow Exhaust Enthalpy 1D Engine model can be used Directly into the System Model as FRM Engine model To feed EngineState model with Heat, Fuel & Enthalpy Maps

9 Generating Engine outputs by using Customer data 1D Engine Model generates engine Outputs based on Vehicle data but Requires time to be built Not suitable for quick system evaluation (evaluation for customer) Bench data Analysis : engine outputs based on 0D Engine model Drawbacks Based on test data Not predictive Advantages Estimates EHRS Impact with customer data Uses widely available data Principle Calculation of Fuel to Heat efficiency & Calibration of Ambient Losses from bench transient profiles Data Analysis Engine Mass flow Coolant Temperature Material Masses Coolant Volume Ambient Temperature 9 Combustion Heat transfer Ambient Losses transfer

10 Cooling system Cooling Model Data Measured data Fluid & Components masses Pipes geometry Bench Data Radiator Heat power CAD estimated data Fluid mass distribution Heat transfer Area Cooling Model Ambient Losses TWall Solver on each pipe + Engine Case HT Area Cabin Model Cabin Volume Cabin ambient losses Engine Model Combustion Heat Rejection Engine Speed Pump flow 1D Cooling model is the key of Vehicle Model : translates EHRS design to understandable values From EHRS Gas To Coolant heat transfer to Coolant temperature improved heating Fuel economy through earlier combustion engine shut-off Cabin Comfort with higher increase in cabin temperature profile

11 EHRS 1D model Component Overview EHRS = liquid / gas heat exchanger Counter-flow Shell / Tube heat exchanger Integrated bypass to avoid engine coolant overheating when coolant reach control temperature Heat Recovery mode Bypass mode Coolant outlet Gas inlet Coolant inlet Bypass valve Gas outlet Bypass valve is closed Exhaust gases enters tubes and are cooled down by the engine coolant in the shell Bypass valve is opened Exhaust gases do not enter exchanger 11

12 EHRS 1D model Component Overview FECT build up complete exchanger specifications Type of tubes Corrugated Internal fins Number of tubes wax vacuum electric Bypass actuator type Wax actuator (opens when wax melts) Vacuum actuator (use vacuum network of engine) Electric actuator (use electrical command) For this study, we will use Finned tubes + vaccum actuator Title - Place - Date 12

13 EHRS 1D Model Thermal / mass balance Q U tttt Steady thermal balance Q cccc,ii Q bbbb Q cccc,ooo Q BB,ii : Inlet bypass heat losses Q BB,ooo : Outlet bypass heat losses Q cccc,ii : Inlet cone heat losses Q cccc,ooo : outlet cone heat losses Q U tttt : U-turn heat losses Q bbbb : Exchanger body heat losses Q ggg = Q cccc + ΣQ Steady mass balance llllll m eee m hx m llll m eee : exhaust inlet mass flow m HH : effective exchanger mass flow m llll : gas leakage through bypass m hh = m eee m llllll Q BB,ii Q BB,ooo The more accurate the assumptions, the easiest the calibration process 13

14 EHRS 1D model Way to model heat exchanger within GT Master/Slave Built-in template + Easy to build with experimental data + Scaling capability - Heat transfer maps include all losses - Out of range behavior? - No internal finned tube template Detailed Primitive flow & thermal components + Complete thermal balance + Better bypass modelling (can include leak) + Could be used for acoustic modeling - Require more time to build - Require CAD data Detailed model is well adapted for our application 14

15 EHRS 1D model Detailed model Detail model discretize heat exchanger using primitive template Flow pipes: gas and coolant path Thermal masses: wall / fins Thermal connections: convection / conduction / radiation FlowSplits: cones / fluid distribution Example of discretized exchanger A custom PipeFin template was created to avoid a (very) long model building task Simplified 1D thermal layout 1x gas + fin element Custom PipeFin template 15

16 EHRS 1D model Complete Layout External losses Exchanger Coolant flow Inlet cone Outlet cone Gas flow Bypass Thanks to user compounds, model map looks quite simple 16

17 EHRS 1D model Calibration workflow 3D to 1D geometry simplification Heat transfer area Hydraulic diameter CFD Calibration Gas and coolant HTM calibration Gas and coolant pressure drop calibration Synthetic gas bench Valve leakages calibration : gas pressure drop matching Engine bench: Driving cycle Transient / global validation 17

18 Experimental vs simulation NEDC: Temperature HEAT RECOVERY MODE BYPASS MODE High mass flow = low ΔT better consider heat rate Detailed model better predict gas temperature, especially in bypass mode 18

19 Experimental vs simulation NEDC: Heat rate Gas heat rate Detailed model better predict coolant and gas heat rate Detailed model can predict some «parasitic losses» (heat transfer into coolant when bypassed) Detailed model is more reliable in out of range mode 19 Coolant heat rate Experimental 1000 W 515 W Detailed 938 W 593 W Hx Master/Slave 657 W 647 W

20 System Model outputs & Results EHRS Heating Power Quicker Coolant heating Lower ICE Request Faster Cabin Heating Lower Fuel consumption Cabin Heating is improved with noticeable reduced time to reach target temperature Electric Load of Auxilliary heaters could be decreased : SOC savings Fuel Consumption is decreased by up to 8% on cold conditions In line with OEM claims & experimental test resuls 20

21 Conclusion A method has been developed to build a Transient 1D EHRS model under GT suite It can be used for various purpose Using customer input, predict how much heat can be extracted It can be embedded in a vehicle model to perform system model Comparison can be made with other exchanger model to compare performances This model can generate maps to feed an HxSlave model to perform scaling studies Simulation plateform is valuable to Simulate any powertrain and thermal management strategies Simulate any exhaust configuration and EHRS architectures Estimate benefits of our component on customer systems Title - Place - Date 21

22 THANK YOU FOR YOUR ATTENTION!!

THERMAL MANAGEMENT SYNERGY THROUGH INTEGRATION PETE BRAZAS

THERMAL MANAGEMENT SYNERGY THROUGH INTEGRATION PETE BRAZAS THERMAL MANAGEMENT SYNERGY THROUGH INTEGRATION PETE BRAZAS 1 Propulsion System Trends Evolution of the TMM A Closer Look at Electrification System Integration Approach Outlook Powertrain Technology Roadmap

More information

Prediction of Engine Warm-up and Fuel Economy utilizing GT s Customized FE Cylinder Structure Objects

Prediction of Engine Warm-up and Fuel Economy utilizing GT s Customized FE Cylinder Structure Objects Prediction of Engine Warm-up and Fuel Economy utilizing GT s Uliana Bryakina Gerald Seider Frankfurt, October 16, 2016 European GT Conference 2016 InDesA GmbH Carl-Zeiss-Ring 19a D-85737 Ismaning Phone

More information

Engine Warm-up Prediction of Combustion Engines for Fuel Economy Drive Cycles

Engine Warm-up Prediction of Combustion Engines for Fuel Economy Drive Cycles Engine Warm-up Prediction of Combustion Engines for Fuel Economy Drive Cycles Gerald Seider Fabiano Bet Uliana Bryakina Prague, March 8, 2016 InDesA GmbH Carl-Zeiss-Ring 19a D-85737 Ismaning Phone +49

More information

MODELING ENGINE FRICTION WITH TEMPERATURE DEPENDENCE FOR VEHICLE THERMAL MANAGEMENT

MODELING ENGINE FRICTION WITH TEMPERATURE DEPENDENCE FOR VEHICLE THERMAL MANAGEMENT MODELING ENGINE FRICTION WITH TEMPERATURE DEPENDENCE FOR VEHICLE THERMAL MANAGEMENT Roberto Rastelli, Xiaobing Liu BorgWarner Inc. Brad Tillock EngSim Corporation Objective and Approach Simulation and

More information

Balancing operability and fuel efficiency in the truck and bus industry

Balancing operability and fuel efficiency in the truck and bus industry Balancing operability and fuel efficiency in the truck and bus industry Realize innovation. Agenda The truck and bus industry is evolving Model-based systems engineering for truck and bus The voice of

More information

European GT-SUITE Conference 2009 page 1. European GT-SUITE Conference Frankfurt, State-of-the-art and Future Requirements for

European GT-SUITE Conference 2009 page 1. European GT-SUITE Conference Frankfurt, State-of-the-art and Future Requirements for page 1 European GT-SUITE Conference Frankfurt, 09.11.2009 State-of-the-art and Future Requirements for Vehicle Dr. Gerald Seider Dr. Fabiano Bet InDesA VTM GmbH InDesA GmbH page 2 Key Applications Design

More information

DOC design & sizing using GT-SUITE European GT Conference Gauthier QUENEY 09/10/2017

DOC design & sizing using GT-SUITE European GT Conference Gauthier QUENEY 09/10/2017 DOC design & sizing using GT-SUITE European GT Conference 2017 Gauthier QUENEY 09/10/2017 Background Simulation tool target Predict exhaust outlet emissions Thermal modeling Chemical modeling This presentation

More information

Integrated Powertrain Simulation for Energy Management of Hybrid Electric Vehicles

Integrated Powertrain Simulation for Energy Management of Hybrid Electric Vehicles Integrated Powertrain Simulation for Energy Management of Hybrid Electric Vehicles October 24 th, 2011 Kentaro Watanabe Nissan Motor Co., Ltd. 1 Outline 1. Motivation 2. Simulation technology 3. Recent

More information

Study of a hybrid cooling system using GT-Suite

Study of a hybrid cooling system using GT-Suite PAYET-BURIN Thomas (Alten) Direction de la Qualité et de l Ingénierie Agenda Introduction Hydraulic studies Overview of the architecture of a hybrid cooling system Hydraulic correlation Architecture choices

More information

Modeling the Electrically Assisted Variable Speed (EAVS) Supercharger

Modeling the Electrically Assisted Variable Speed (EAVS) Supercharger Modeling the Electrically Assisted Variable Speed (EAVS) Supercharger Eaton Corporation Vehicle Group Brian Smith Brandon Biller Overview of EAVS Technology 2 EAVS System Development at Eaton Hardware

More information

GT-Suite European User Conference

GT-Suite European User Conference GT-Suite European User Conference E-Charging on a High Performance Diesel engine D. Peci, C. Venezia EMEA Region - Powertrain Engineering Powertrain Research&Technology Frankfurt, Germany October 26th,

More information

Component and System Level Modeling of a Two-Phase Cryogenic Propulsion System for Aerospace Applications

Component and System Level Modeling of a Two-Phase Cryogenic Propulsion System for Aerospace Applications Component and System Level Modeling of a Two-Phase Cryogenic Propulsion System for Aerospace Applications J. LoRusso, B. Kalina, M. Van Benschoten, Roush Industries GT Users Conference November 9, 2015

More information

Thermoelectric Network Meeting Engineering Challenges and the Thermoelectric Roadmap Market Applications and Future Activities

Thermoelectric Network Meeting Engineering Challenges and the Thermoelectric Roadmap Market Applications and Future Activities Thermoelectric Network Meeting Engineering Challenges and the Thermoelectric Roadmap Market Applications and Future Activities Dr Cedric Rouaud, Chief Engineer, Engines Product Group 2 Content Key market

More information

State of the art cooling system development for automotive applications

State of the art cooling system development for automotive applications State of the art cooling system development for automotive applications GT Conference 2017, Frankfurt A. Fezer, TheSys GmbH P. Sommer, A. Diestel, Mercedes-AMG GmbH Content Introduction Cooling system

More information

Virtual Testing for Automotive Components and its Integration into the OEM s Product Creation Process. Dr. Gerald Seider Dr.

Virtual Testing for Automotive Components and its Integration into the OEM s Product Creation Process. Dr. Gerald Seider Dr. Virtual Testing for Automotive Components and its Integration into the OEM s Product Creation Process Dr. Gerald Seider Dr. Fabiano Bet Orlando, 18 March, 2013 Company Profile Consulting, Engineering Services

More information

Engine encapsulation. A synergic approach to exterior noise and CO 2 emissions reduction. Brussels, 18th December 2012 Maurizio Mantovani - Autoneum

Engine encapsulation. A synergic approach to exterior noise and CO 2 emissions reduction. Brussels, 18th December 2012 Maurizio Mantovani - Autoneum Engine encapsulation A synergic approach to exterior noise and CO 2 emissions reduction Brussels, 18th December 2012 Maurizio Mantovani - Autoneum Agenda 1. Who is Autoneum 2. Benefits of encapsulation

More information

Exhaust line simulations using Star-CCM+ and automation Yohann Perrot

Exhaust line simulations using Star-CCM+ and automation Yohann Perrot Exhaust line simulations using Star-CCM+ and automation Yohann Perrot 22-March-2010 Agenda Faurecia Emissions Control Technologies Exhaust line components Some correlations and investigations Enhancements

More information

LITENS ADVANCED THERMAL MANAGEMENT SOLUTIONS FOR IMPROVING ENGINE WARM-UP AND FUEL ECONOMY

LITENS ADVANCED THERMAL MANAGEMENT SOLUTIONS FOR IMPROVING ENGINE WARM-UP AND FUEL ECONOMY LITENS ADVANCED THERMAL MANAGEMENT SOLUTIONS FOR IMPROVING ENGINE WARM-UP AND FUEL ECONOMY Jason Zheng, Noel Abreu, Bin Cheng Litens Automotive Partnership Company Logo Here Outline Introduction Litens

More information

Simulation Model for a Gasoline Engine with Advanced Thermal Control

Simulation Model for a Gasoline Engine with Advanced Thermal Control page 1 Vehicle Thermal Management Systems Conference and Exhibition Gaydon, UK 15-19 May 2011 A High-Resolution Warm-Up Simulation Model for a Gasoline Engine with Advanced Thermal Control Dr. Gerald Seider,

More information

Emissions and Fuel Consumption Trade-offs of a Turbocharged Diesel Engine Equipped with Electrically Heated Catalyst

Emissions and Fuel Consumption Trade-offs of a Turbocharged Diesel Engine Equipped with Electrically Heated Catalyst Emissions and Fuel Consumption Trade-offs of a Turbocharged Diesel Engine Equipped with Electrically Heated Catalyst 2012 CLEERS Wen Wang 1, Jon Brown 1, Dominik Artukovic 2, Enrico Pautasso 3, and Emanuele

More information

THE FKFS 0D/1D-SIMULATION. Concepts studies, engineering services and consulting

THE FKFS 0D/1D-SIMULATION. Concepts studies, engineering services and consulting THE FKFS 0D/1D-SIMULATION Concepts studies, engineering services and consulting r e s e a r c h i n m o t i o n. VEHICLE IN MOTION On the basis of constant engine speeds and loads, the combustion engine

More information

Integrated Engine and Coolant Circuit Modeling with GT-SUITE. Oliver Roessler Vincenzo Bevilacqua, Raymond Reinmann

Integrated Engine and Coolant Circuit Modeling with GT-SUITE. Oliver Roessler Vincenzo Bevilacqua, Raymond Reinmann Integrated Engine and Coolant Circuit Modeling with GT-SUITE Oliver Roessler Vincenzo Bevilacqua, Raymond Reinmann 1 Overview Objective Simulation Steps Model build-up & Variants Integration Conclusion

More information

MODULAR WATER CHARGE AIR COOLING FOR COMBUSTION ENGINES

MODULAR WATER CHARGE AIR COOLING FOR COMBUSTION ENGINES DEVELOPMENT Thermal management MODULAR WATER CHARGE AIR COOLING FOR COMBUSTION ENGINES Valeo shows which considerations were taken into account with the development of a modular water charge air cooling

More information

Early Stage Vehicle Concept Design with GT-SUITE

Early Stage Vehicle Concept Design with GT-SUITE 1/18 Early Stage Vehicle Concept Design with GT-SUITE Katsuya Minami Honda R&D Co., Ltd., Automotive R&D Center, Japan Benefits of 1D-Simulation 2/18 How each component is operating during legislative

More information

Investigation of Radiators Size, Orientation of Sub Cooled Section and Fan Position on Twin Fan Cooling Packby 1D Simulation

Investigation of Radiators Size, Orientation of Sub Cooled Section and Fan Position on Twin Fan Cooling Packby 1D Simulation Investigation of Radiators Size, Orientation of Sub Cooled Section and Fan Position on Twin Fan Cooling Packby 1D Simulation Neelakandan K¹, Goutham Sagar M², Ajay Virmalwar³ Abstract: A study plan to

More information

OPTIMIZATION STUDIES OF ENGINE FRICTION EUROPEAN GT CONFERENCE FRANKFURT/MAIN, OCTOBER 8TH, 2018

OPTIMIZATION STUDIES OF ENGINE FRICTION EUROPEAN GT CONFERENCE FRANKFURT/MAIN, OCTOBER 8TH, 2018 OPTIMIZATION STUDIES OF ENGINE FRICTION EUROPEAN GT CONFERENCE FRANKFURT/MAIN, OCTOBER 8TH, 2018 M.Sc. Oleg Krecker, PhD candidate, BMW B.Eng. Christoph Hiltner, Master s student, Affiliation BMW AGENDA

More information

Integrated Simulation of a Truck Diesel Engine with a Hydraulic Engine Braking System

Integrated Simulation of a Truck Diesel Engine with a Hydraulic Engine Braking System Integrated Simulation of a Truck Diesel Engine with a Hydraulic Engine Braking System N. Brinkert, K. Kanning GT-Suite Users Conference 2008 I want to give you a short presentation about a project we work

More information

MODELING ELECTRIFIED VEHICLES UNDER DIFFERENT THERMAL CONDITIONS

MODELING ELECTRIFIED VEHICLES UNDER DIFFERENT THERMAL CONDITIONS MODELING ELECTRIFIED VEHICLES UNDER DIFFERENT THERMAL CONDITIONS Namwook Kim, Neeraj Shidore, Dominik Karbowski, Aymeric Rousseau Argonne National Laboratory Electrical consumption (wh/milie) Temperature

More information

Integration of Lubrication and Cooling System GT-SUITE Models

Integration of Lubrication and Cooling System GT-SUITE Models Integration of Lubrication and Cooling System GT-SUITE Models North American GT Conference 2017 Presenter: Robert Fry Agenda Introduction Cooling System Model Development Lubrication System Model Development

More information

Seeing Sound: A New Way To Reduce Exhaust System Noise

Seeing Sound: A New Way To Reduce Exhaust System Noise \ \\ Seeing Sound: A New Way To Reduce Exhaust System Noise Why Do You Need to See Sound? Vehicle comfort, safety, quality, and driver experience all rely on controlling the noise made by multiple systems.

More information

Performance analysis of TEGs applied in the EGR path of a heavy duty engine for a Transient Drive Cycle

Performance analysis of TEGs applied in the EGR path of a heavy duty engine for a Transient Drive Cycle Performance analysis of TEGs applied in the EGR path of a heavy duty engine for a Transient Drive Cycle Thermo-electric Group Department of Aeronautical and Automotive Engineering Prof. Richard Stobart

More information

Thermal influence on engine intake air

Thermal influence on engine intake air Fabiano Bet Gerald Seider Marcel Hülssiep Berlin, March 7, 2017 InDesA GmbH Carl-Zeiss-Ring 19a D-85737 Ismaning Phone +49 (89) 552 7978-10 Fax +49 (89) 552 7978-29 www.indesa.de Consulting, Engineering

More information

EFFICIENZA E ANALISI TERMICA. Ing. Ivan Saltini Italy Country Manager

EFFICIENZA E ANALISI TERMICA. Ing. Ivan Saltini Italy Country Manager EFFICIENZA E ANALISI TERMICA Ing. Ivan Saltini Italy Country Manager How to get most realistic efficiency calculation for gearboxes? Topics Motivation / general calculation Industrial bevel-helical gearbox

More information

Calibration. DOE & Statistical Modeling

Calibration. DOE & Statistical Modeling ETAS Webinar - ASCMO Calibration. DOE & Statistical Modeling Injection Consumption Ignition Torque AFR HC EGR P-rail NOx Inlet-cam Outlet-cam 1 1 Soot T-exhaust Roughness What is Design of Experiments?

More information

Engine Encapsulation for Increased Fuel Efficiency of Road Vehicles

Engine Encapsulation for Increased Fuel Efficiency of Road Vehicles Engine Encapsulation for Increased Fuel Efficiency of Road Vehicles A project within the program: Energy and Environment Start: July 2013 End: June 2017 Blago Minovski Department of Mechanics and Maritime

More information

UNIAIR Variable Valve Actuation System Modelling and Integration to the Engine in the GT-SUITE environment

UNIAIR Variable Valve Actuation System Modelling and Integration to the Engine in the GT-SUITE environment 2008 European Conference Frankfurt am Main October, 20th Variable Valve Actuation System Modelling Integration to the Engine in the environment Paolo Ferreri - Caterina Venezia FPT Research & Mechanical

More information

GT-Suite Users International Conference Frankfurt a.m., October 22 nd 2012

GT-Suite Users International Conference Frankfurt a.m., October 22 nd 2012 GT-Suite Users International Conference Frankfurt a.m., October 22 nd 2012 Computational Analysis of Internal and External EGR Strategies combined with Miller Cycle Concept for a Two Stage Turbocharged

More information

Gas exchange and fuel-air mixing simulations in a turbocharged gasoline engine with high compression ratio and VVA system

Gas exchange and fuel-air mixing simulations in a turbocharged gasoline engine with high compression ratio and VVA system Third Two-Day Meeting on Internal Combustion Engine Simulations Using the OpenFOAM technology, Milan 22 nd -23 rd February 2018. Gas exchange and fuel-air mixing simulations in a turbocharged gasoline

More information

Research Report. FD807 Electric Vehicle Component Sizing vs. Vehicle Structural Weight Report

Research Report. FD807 Electric Vehicle Component Sizing vs. Vehicle Structural Weight Report RD.9/175.3 Ricardo plc 9 1 FD7 Electric Vehicle Component Sizing vs. Vehicle Structural Weight Report Research Report Conducted by Ricardo for The Aluminum Association 9 - RD.9/175.3 Ricardo plc 9 2 Scope

More information

Vehicle simulation with cylinder deactivation

Vehicle simulation with cylinder deactivation Vehicle simulation with cylinder deactivation Potential analysis of cylinder deactivation using a detailed Cyrille Frottier, Lars Böttcher, GT-SUITE Users Conference, October 2011 Vehicle simulation with

More information

Put Paper Number Here

Put Paper Number Here Proceedings of 2003 Diesel Engine Emissions Reduction Conference Newport, Rhode Island, August 24-28, 2003 Put Paper Number Here THERMOELECTRICAL ENERGY RECOVERY FROM THE EXHAUST OF A LIGHT TRUCK Madhav

More information

Design and evaluate vehicle architectures to reach the best trade-off between performance, range and comfort. Unrestricted.

Design and evaluate vehicle architectures to reach the best trade-off between performance, range and comfort. Unrestricted. Design and evaluate vehicle architectures to reach the best trade-off between performance, range and comfort. Unrestricted. Introduction Presenter Thomas Desbarats Business Development Simcenter System

More information

Cooling System Simulation for Indian Utility Vehicle using COOL3D

Cooling System Simulation for Indian Utility Vehicle using COOL3D Indian GT SUITE Conference 2013 Cooling System Simulation for Indian Utility Vehicle using COOL3D Paper presented by Rishabh Pandey, M&M Gopakishore Gummadi, M&M Copyright 2012 Mahindra & Mahindra Ltd.

More information

Case study on Selective catalytic reduction(scr) performance improvement over legislative engine cycles using 1D simulation

Case study on Selective catalytic reduction(scr) performance improvement over legislative engine cycles using 1D simulation Case study on Selective catalytic reduction(scr) performance improvement over legislative engine cycles using 1D simulation Presented by Mohak Samant & Hitesh Chaudhari Under the guidance of Dr. N. H.

More information

Modelling of Diesel Vehicle Emissions under transient conditions

Modelling of Diesel Vehicle Emissions under transient conditions Modelling of Diesel Vehicle Emissions under transient conditions Dr. Gavin Dober Combustion and Hydraulics Manager, Davide Del Pozzo Delphi Trainee 216-217 Advanced Injection & Combustion Center Delphi

More information

Mobile Air Conditioning (MAC)

Mobile Air Conditioning (MAC) Mobile Air Conditioning (MAC) Working paper No. MACTP-1-3 (Geneva, 8 June 21) Test procedure development Progress update 8-6-21 Contents Project overview Progress made so far Identification of major influential

More information

Part Load Engine Performance prediction for a gasoline engine using Neural Networks. Sreekanth R, Sundar S, Rangarajan S, Anand G -System Simulation

Part Load Engine Performance prediction for a gasoline engine using Neural Networks. Sreekanth R, Sundar S, Rangarajan S, Anand G -System Simulation Part Load Engine Performance prediction for a gasoline engine using Neural Networks Sreekanth R, Sundar S, Rangarajan S, Anand G -System Simulation CAE-2 System Simulation GT-SUITE User Conference Feb

More information

Integrated Simulation Technologies Pvt Ltd

Integrated Simulation Technologies Pvt Ltd UHC System Sizing to Eliminate Engine Overheating when Grill and Radiator Fronts are Partially Blocked by Mud & Dirt Integrated Simulation Technologies Pvt Ltd Subir Mandal IST India GT-SUITE Conference

More information

Well-to-Wheel Analysis of Electrified Drivetrains under Realistic Boundary Conditions and User Behaviour

Well-to-Wheel Analysis of Electrified Drivetrains under Realistic Boundary Conditions and User Behaviour Well-to-Wheel Analysis of Electrified Drivetrains under Realistic Boundary Conditions and User Behaviour Benedikt Hollweck European GT Conference, Frankfurt am Main, 17 th October 2016 Agenda 1. What is

More information

USE OF 1D SIMULATION IN THE COOLING SYSTEMS DESIGN PROCESS

USE OF 1D SIMULATION IN THE COOLING SYSTEMS DESIGN PROCESS Dr. Bernhard Zuck; 24.10.2011 USE OF 1D SIMULATION IN THE COOLING SYSTEMS DESIGN PROCESS FROM SYSTEM CONCEPT TO FINAL VALIDATION CONTENT 1. Demands and challenges facing Simulation 2. Considered System

More information

Modeling and thermal simulation of a PHEV battery module with cylindrical LFP cells

Modeling and thermal simulation of a PHEV battery module with cylindrical LFP cells Modeling and thermal simulation of a PHEV battery module with cylindrical LFP cells Paolo Cicconi, Michele Germani, Daniele Landi Università Politecnica delle Marche, Ancona, Italy Outline Research context

More information

Modelling and Simulation Specialists

Modelling and Simulation Specialists Modelling and Simulation Specialists Multi-Domain Simulation of Hybrid Vehicles Multiphysics Simulation for Autosport / Motorsport Applications Seminar UK Magnetics Society Claytex Services Limited Software,

More information

Optimising Aeristech FETT (Fully Electric Turbocharger Technology) for Future Gasoline Engine Requirements

Optimising Aeristech FETT (Fully Electric Turbocharger Technology) for Future Gasoline Engine Requirements Optimising Aeristech FETT (Fully Electric Turbocharger Technology) for Future Gasoline Engine Requirements Dr Sam Akehurst, Dr Nic Zhang 25 th April 2017 1 Contents Introduction to the Fully Electric Turbocharging

More information

VT2+: Further improving the fuel economy of the VT2 transmission

VT2+: Further improving the fuel economy of the VT2 transmission VT2+: Further improving the fuel economy of the VT2 transmission Gert-Jan Vogelaar, Punch Powertrain Abstract This paper reports the study performed at Punch Powertrain on the investigations on the VT2

More information

ELECTRICAL 48 V MAIN COOLANT PUMP TO REDUCE CO 2 EMISSIONS

ELECTRICAL 48 V MAIN COOLANT PUMP TO REDUCE CO 2 EMISSIONS ELECTRICAL 48 V MAIN COOLANT PUMP TO REDUCE CO 2 EMISSIONS Mahle has developed an electrical main coolant pump for the 48 V on-board net. It replaces the mechanical pump and offers further reductions in

More information

Development of Variable Geometry Turbocharger Contributes to Improvement of Gasoline Engine Fuel Economy

Development of Variable Geometry Turbocharger Contributes to Improvement of Gasoline Engine Fuel Economy Development of Variable Geometry Turbocharger Contributes to Improvement of Gasoline Engine Fuel Economy 30 MOTOKI EBISU *1 YOSUKE DANMOTO *1 YOJI AKIYAMA *2 HIROYUKI ARIMIZU *3 KEIGO SAKAMOTO *4 Every

More information

Electrical 48-V Main Coolant Pump to Reduce CO 2 Emissions

Electrical 48-V Main Coolant Pump to Reduce CO 2 Emissions DEVELOPMENT Cooling Electrical 48-V Main Coolant Pump to Reduce CO 2 Emissions Mahle has developed an electrical main coolant pump for the 48-V on-board net. It replaces the mechanical pump and offers

More information

Vehicle Simulation for Engine Calibration to Enhance RDE Performance

Vehicle Simulation for Engine Calibration to Enhance RDE Performance Vehicle Simulation for Engine Calibration to Enhance RDE Performance IPG Apply & Innovate 2018 11st and 12nd of September, Karlsruhe, Germany Dr. Yutaka Murata Yui Nishio Dr. Yukihisa Yamaya Masato Kikuchi

More information

Dongfeng Commercial Vehicle

Dongfeng Commercial Vehicle Automotive and transportation Dongfeng Commercial Vehicle Product Simcenter Leading truck manufacturer optimizes engine cooling controls strategies with Simcenter Amesim Business challenges Cut truck development

More information

Truck Cooling Package Optimization. Reducing the size of a cooling package thanks to 1-D Transient simulations

Truck Cooling Package Optimization. Reducing the size of a cooling package thanks to 1-D Transient simulations Truck Cooling Package Optimization Reducing the size of a cooling package thanks to 1-D Transient simulations VOLVO group presentation What we do ON THE ROAD IN THE CITY We employ almost 100,000 PEOPLE,

More information

Transmission Technology contribution to CO 2 roadmap a benchmark

Transmission Technology contribution to CO 2 roadmap a benchmark Transmission Technology contribution to CO 2 roadmap a benchmark Martin Bahne Director Attribute System Engineering Ulrich Frey Technical specialist Agenda Introduction Transmission Technology Benchmark

More information

Utilizing a Small Efficient DCT for the Chinese Market

Utilizing a Small Efficient DCT for the Chinese Market Utilizing a Small Efficient DCT for the Chinese Market Drivetrain Forum 2016, Untergruppenbach Sascha K. Mierbach GETRAG, Platform Director Small DCT, Magna Powertrain Utilizing a Small Efficient DCT for

More information

Electrified Vehicles as Platforms for Complex System Control

Electrified Vehicles as Platforms for Complex System Control Electrified Vehicles as Platforms for Complex System Control Technical Research Department Hasan Esen 03.09.2012 HYCON2 WORKSHOP ON ENERGY AGENDA 2 / 16 1. DENSO Corporation Company Profile 2. Increasing

More information

Predicting Oil Flow Distribution in a High Performance NASCAR Engine

Predicting Oil Flow Distribution in a High Performance NASCAR Engine Predicting Oil Flow Distribution in a High Performance NASCAR Engine GT-SUTE Conference Birmingham-MI, November 7, 2011 Paul Bolton Earnhardt-Childress Racing Presentation Overview Introduction Why model

More information

elektronik Designing vehicle power nets A single simulation tool from initial requirements to series production

elektronik Designing vehicle power nets A single simulation tool from initial requirements to series production www.atzonline.de elektronik 04 April 2013 Volume 8 Offprint from ATZelektronik 4/2013 Springer Automotive Media Springer Fachmedien Wiesbaden GmbH for Bosch Engineering Designing vehicle power nets A single

More information

Vehicle and Drive Cycle Simulation of a Vacuum Insulated Catalytic Converter

Vehicle and Drive Cycle Simulation of a Vacuum Insulated Catalytic Converter Vehicle and Drive Cycle Simulation of a Vacuum Insulated Catalytic Converter Rohil Daya 9 th November 2015 Introduction The drive to control automobile emissions began with the enactment of the first emissions

More information

COOLING SYSTEM - V8. Cooling system component layout DESCRIPTION AND OPERATION

COOLING SYSTEM - V8. Cooling system component layout DESCRIPTION AND OPERATION Cooling system component layout 26-2-2 DESCRIPTION AND OPERATION 1 Heater matrix 2 Heater return hose 3 Heater inlet hose 4 Heater inlet pipe 5 Throttle housing 6 Connecting hose 7 Throttle housing inlet

More information

Determination of a turbocharged gasoline engine for hybrid powertrains. F. Kercher,

Determination of a turbocharged gasoline engine for hybrid powertrains. F. Kercher, Determination of a turbocharged gasoline engine for hybrid powertrains F. Kercher, 26.10.2015 Determination of a turbocharged gasoline engine for hybrid powertrains Agenda Introduction Hybrid Electric

More information

12V / 48V Hybrid Vehicle Technology Steven Kowalec

12V / 48V Hybrid Vehicle Technology Steven Kowalec 12V / 48V Hybrid Vehicle Technology Steven Kowalec www.continental-corporation.com Powertrain Division Powertrain Electrification Technology Sy ystem Costs CO2 Reduction Potenttial Mi Micro-hybrids h b

More information

Heat Transfer in Engines. Internal Combustion Engines

Heat Transfer in Engines. Internal Combustion Engines Heat Transfer in Engines Internal Combustion Engines Energy Distribution Removing heat is critical in keeping an engine and lubricant from thermal failure Amount of energy available for use: Brake thermal

More information

Use of Flow Network Modeling for the Design of an Intricate Cooling Manifold

Use of Flow Network Modeling for the Design of an Intricate Cooling Manifold Use of Flow Network Modeling for the Design of an Intricate Cooling Manifold Neeta Verma Teradyne, Inc. 880 Fox Lane San Jose, CA 94086 neeta.verma@teradyne.com ABSTRACT The automatic test equipment designed

More information

James Goss, Mircea Popescu, Dave Staton. 11 October 2012, Stuttgart, Germany

James Goss, Mircea Popescu, Dave Staton. 11 October 2012, Stuttgart, Germany Implications of real-world drive cycles on efficiencies and life cycle costs of two solutions for HEV traction: Synchronous PM motor vs Copper Rotor - IM James Goss, Mircea Popescu, Dave Staton 11 October

More information

Validation and Optimization of Front End Cooling Module for Commercial Vehicle using CFD Simulation

Validation and Optimization of Front End Cooling Module for Commercial Vehicle using CFD Simulation Validation and Optimization of Front End Cooling Module for Commercial Vehicle using CFD Simulation Ashok Patidar, Umashanker Gupta, Nitin Marathe VE Commercial Vehicles Ltd. INDIA (A VOLVO GROUP AND EICHER

More information

VEHICLE ELECTRIFICATION INCREASES EFFICIENCY AND CONSUMPTION SENSITIVITY

VEHICLE ELECTRIFICATION INCREASES EFFICIENCY AND CONSUMPTION SENSITIVITY VEHICLE ELECTRIFICATION INCREASES EFFICIENCY AND CONSUMPTION SENSITIVITY Henning Lohse-Busch, Ph.D. Argonne National Laboratory Argonne s Center for Transportation Research Basic & Applied Combustion Research

More information

Performance Prediction of Automotive Air Conditioning System for Different Driving Cycle Conditions

Performance Prediction of Automotive Air Conditioning System for Different Driving Cycle Conditions Performance Prediction of Automotive Air Conditioning System for Different Driving Cycle Conditions Rangarajan S a, Yamamuro Tsuyoshi b, SasiKumar M a, Kubo Masaaki b, Anand G a a Renault Nissan Technology

More information

Thermoelectric Vehicular Applications Status Mid 2009

Thermoelectric Vehicular Applications Status Mid 2009 Thermoelectric Vehicular Applications Status Mid 2009 John W. Fairbanks Department of Energy Vehicle Technologies August 12, 2009 MIT-NESCAUM Symposium on Energy Dedham, MA International Thermoelectric

More information

GT-Power Report. By Johan Fjällman. KTH Mechanics, SE Stockholm, Sweden. Internal Report

GT-Power Report. By Johan Fjällman. KTH Mechanics, SE Stockholm, Sweden. Internal Report GT-Power Report By Johan Fjällman KTH Mechanics, SE- 44 Stockholm, Sweden Internal Report Presently in the vehicle industry full engine system simulations are performed using different one-dimensional

More information

Experience the Hybrid Drive

Experience the Hybrid Drive Experience the Hybrid Drive MAGNA STEYR equips SUV with hybrid drive Hybrid demo vehicle with dspace prototyping system To integrate components into a hybrid vehicle drivetrain, extensive modification

More information

SuperGen - Novel Low Cost Electro-Mechanical Mild Hybrid and Boosting System. Jason King, Chief Engineer

SuperGen - Novel Low Cost Electro-Mechanical Mild Hybrid and Boosting System. Jason King, Chief Engineer SuperGen - Novel Low Cost Electro-Mechanical Mild Hybrid and Boosting System Jason King, Chief Engineer FPC2015 Quick overview of Integral Powertrain (IPT) SuperGen concept Analysis results Test results

More information

INTEGRATED HYDRO-MECHANICAL SIMULATION OF A CAM-ROCKER ARM-UNIT INJECTOR SYSTEM TO ADDRESS NOISE AND VIBRATION ISSUES

INTEGRATED HYDRO-MECHANICAL SIMULATION OF A CAM-ROCKER ARM-UNIT INJECTOR SYSTEM TO ADDRESS NOISE AND VIBRATION ISSUES GT-Suite Users Conference Frankfurt, Germany, October 10 th 2005 INTEGRATED HYDRO-MECHANICAL SIMULATION OF A CAM-ROCKER ARM-UNIT INJECTOR SYSTEM TO ADDRESS NOISE AND VIBRATION ISSUES R. HAM, H. FESSLER

More information

Greenhouse gas Emission Model (GEM) A Compliance Vehicle Model for Certification

Greenhouse gas Emission Model (GEM) A Compliance Vehicle Model for Certification Greenhouse gas Emission Model (GEM) A Compliance Vehicle Model for Certification Dr. Houshun Zhang Environmental Protection Agency January 22, 2018 GEM Background Outline Technology Assessment in GHG Phase

More information

Addressing performance balancing in fuel economy driven vehicle programs

Addressing performance balancing in fuel economy driven vehicle programs EAEC-ESFA 2015 Presenter: Dr. Filip Deblauwe Addressing performance balancing in fuel economy driven vehicle programs Smarter decisions, better products. Introduction Performance balancing Application

More information

FLUID DYNAMICS TRANSIENT RESPONSE SIMULATION OF A VEHICLE EQUIPPED WITH A TURBOCHARGED DIESEL ENGINE USING GT-POWER

FLUID DYNAMICS TRANSIENT RESPONSE SIMULATION OF A VEHICLE EQUIPPED WITH A TURBOCHARGED DIESEL ENGINE USING GT-POWER GT-SUITE USERS CONFERENCE FRANKFURT, OCTOBER 20 TH 2003 FLUID DYNAMICS TRANSIENT RESPONSE SIMULATION OF A VEHICLE EQUIPPED WITH A TURBOCHARGED DIESEL ENGINE USING GT-POWER TEAM OF WORK: A. GALLONE, C.

More information

Sreekanth R, Rangarajan S, Anand G -System Simulation

Sreekanth R, Rangarajan S, Anand G -System Simulation Passenger Car baseline Fuel Economy Validation with Test data on IDC & FE Improvement Strategies Prediction to improve CAFE Ratings Sreekanth R, Rangarajan S, Anand G -System Simulation PWT CAE System

More information

VIPER Vehicle Integrated Powertrain Energy Recovery LCV12 IDP4 Strengthening the UK Supply Chain

VIPER Vehicle Integrated Powertrain Energy Recovery LCV12 IDP4 Strengthening the UK Supply Chain VIPER Vehicle Integrated Powertrain Energy Recovery LCV12 IDP4 Strengthening the UK Supply Chain Meeting Location: Millbrook POWERTRAIN ADVANCED ENGINEERING Bob Gilchrist September 2012 Project Overview

More information

Toyota s Hybrid Technology. Yoshihiro Onomura General Manager, Planning & Administration Dept. Hybrid Vehicle Engineering Management Div.

Toyota s Hybrid Technology. Yoshihiro Onomura General Manager, Planning & Administration Dept. Hybrid Vehicle Engineering Management Div. Toyota s Hybrid Technology Yoshihiro Onomura General Manager, Planning & Administration Dept. Hybrid Vehicle Engineering Management Div. 1 1. Birth of the world s first mass produced hybrid: the Prius

More information

Validation of a simulation model for the assessment of CO 2 emissions of passenger cars under real-world conditions

Validation of a simulation model for the assessment of CO 2 emissions of passenger cars under real-world conditions Validation of a simulation model for the assessment of CO 2 emissions of passenger cars under real-world conditions The gap between real-world fuel consumption and manufacturers figures has been increasing

More information

Model-Based Design and Hardware-in-the-Loop Simulation for Clean Vehicles Bo Chen, Ph.D.

Model-Based Design and Hardware-in-the-Loop Simulation for Clean Vehicles Bo Chen, Ph.D. Model-Based Design and Hardware-in-the-Loop Simulation for Clean Vehicles Bo Chen, Ph.D. Dave House Associate Professor of Mechanical Engineering and Electrical Engineering Department of Mechanical Engineering

More information

Real-world to Lab Robust measurement requirements for future vehicle powertrains

Real-world to Lab Robust measurement requirements for future vehicle powertrains Real-world to Lab Robust measurement requirements for future vehicle powertrains Andrew Lewis, Edward Chappell, Richard Burke, Sam Akehurst, Simon Pickering University of Bath Simon Regitz, David R Rogers

More information

MODELLING OF MOBILE AIR- CONDITIONING SYSTEMS FOR ELECTRIC VEHICLES

MODELLING OF MOBILE AIR- CONDITIONING SYSTEMS FOR ELECTRIC VEHICLES MODELLING OF MOBILE AIR- CONDITIONING SYSTEMS FOR ELECTRIC VEHICLES 4th European Workshop MAC and Vehicle Thermal Systems 2011 B. Torregrosa, J. Payá, J.M. Corberán Torino, December 2 nd, 2011 Content

More information

1D/3D Computational Analysis of a V6 S.I. Variable Intake Manifold

1D/3D Computational Analysis of a V6 S.I. Variable Intake Manifold V6 S.I. Variable Intake Manifold Christof Schernus, Thorsten Märtens, Werner Willems, FEV Motorentechnik GmbH & Co. KG Martin Hopp, Lehrstuhl für Verbrennungskraftmaschinen, RWTH Aachen Heijo Oehlschlegel,

More information

V-CAP TM A FEV VIRTUAL POWERTRAIN CALIBRATION PLATFORM

V-CAP TM A FEV VIRTUAL POWERTRAIN CALIBRATION PLATFORM V-CAP T A FEV VITUAL POWETAIN CALIBATION PLATFO V-CAP T TEST CENTES VITUAL POWETAIN CALIBATION PLATFO V-CAP T VITUAL POWETAIN CALIBATION PLATFO VITUAL TEST BED, EAL ESULTS: A SOLUTION FO PASSENGE CA AND

More information

Module 7: Cooling System Components

Module 7: Cooling System Components  Â  Basic Cooling System Components Radiators Common Types of Radiators Coolant Hoses Water Pumps Centrifugal Force Types of Drives for Water Pumps Types of Drive Belts Basic Cooling System Components

More information

Combining Optimisation with Dymola to Calibrate a 2-zone Predictive Combustion Model.

Combining Optimisation with Dymola to Calibrate a 2-zone Predictive Combustion Model. Combining Optimisation with Dymola to Calibrate a 2-zone Predictive Combustion Model. Mike Dempsey Optimised Engineering Design Conference 2016 Claytex Services Limited Software, Consultancy, Training

More information

Heat Transfer Modeling using ANSYS FLUENT

Heat Transfer Modeling using ANSYS FLUENT Lecture 7 Heat Exchangers 14.5 Release Heat Transfer Modeling using ANSYS FLUENT 2013 ANSYS, Inc. March 28, 2013 1 Release 14.5 Outline Introduction Simulation of Heat Exchangers Heat Exchanger Models

More information

Thermal management of a li-ion battery in a hybrid passenger car within the development process. Dr. Florence Michel, Daimler AG

Thermal management of a li-ion battery in a hybrid passenger car within the development process. Dr. Florence Michel, Daimler AG Thermal management of a li-ion battery in a hybrid passenger car within the development process Dr. Florence Michel, Daimler AG 19.03.2013 Outline 1. Thermal management of HEV battery 2. Numerical process

More information

Hybrid Powertrain Development for Straightforward Vehicle Integration

Hybrid Powertrain Development for Straightforward Vehicle Integration Hybrid Powertrain Development for Straightforward Vehicle Integration Patrick Debal - Punch Powertrain Integrating Electrical & Electronic Vehicle Systems Hethel 20101005 Presentation Overview Punch Powertrain

More information

Efficient and Effective bearing performance evaluation

Efficient and Effective bearing performance evaluation Efficient and Effective bearing performance evaluation The right software platform for dedicated technical questions, based on the right knowledge and design criteria A typical design process Changes SKF

More information

Low Carbon Vehicle Technology Project Benchmarking and Teardown Activities Undertaken on Nissan Leaf and Chevrolet Volt

Low Carbon Vehicle Technology Project Benchmarking and Teardown Activities Undertaken on Nissan Leaf and Chevrolet Volt Low Carbon Vehicle Technology Project Benchmarking and Teardown Activities Undertaken on Nissan Leaf and Chevrolet Volt Johnathan Breddy, Tata Motors European Technical Centre (TMETC) plc Agenda Benchmarking

More information

Chapter 7: Thermal Study of Transmission Gearbox

Chapter 7: Thermal Study of Transmission Gearbox Chapter 7: Thermal Study of Transmission Gearbox 7.1 Introduction The main objective of this chapter is to investigate the performance of automobile transmission gearbox under the influence of load, rotational

More information