Polaris General 60 Rackzilla Instructions
|
|
- Jonah Wright
- 5 years ago
- Views:
Transcription
1 Polaris General 60 Rackzilla Instructions Kit Numbers: Wicked Bilt offers a limited warranty against all manufacturer defects of their kits and supplied parts. Wicked Bilt will not honor any warranty on any parts that have been modified or improperly installed. Full refund will NOT be granted to any kits that are damaged, scratched, or altered in any fashion. Wicked Bilt will not reimburse any labor money to the customer to change out the part even under a warranty repair. Remember before beginning installation, to insure that you are in a well lit, organized work area. Engage the parking brake, disconnect the battery until power is needed and chock or block the rear wheels to insure the vehicle is stable. pg
2 : General 1000 PS (60 ) General P MD General P PS General 1000 EPS General 1000 EPS # Part # Description Qty Rack & Pinion Assembly D.S. Outer End P.S. Outer End /16-18 Locknut /16-18 x ¾ Hex Bolt /16-18 x 3 ¾ Cap Screw 3 Installation: 1. Park vehicle on a flat surface. Center the steering wheel. With a tape measure, measure the distance between the 2 front wheels from the same spot on the tread. Measure the front of the tires and the rear of the tires. The difference is your total toe. Record that measurement. You may need to reset it there when the new rack is installed. NOTE the Rackzilla is preset to factory length. 2. Lift the vehicle so that the wheels are off the ground and secure with jackstands. NOTE you can remove wheels for eaiser installation but not nessasary. pg
3 3. Remove the outer tie rod end bolts from the steering arms on both sides of the vehicle. Note: You may require a mallet for this. 4. Next if a winch is installed remove the 4 bolts from the winch the two power wires and control plug. Locate the hook and remove from cable. Gently take out the winch. Note take pictures or mark the two power wires on the winch. 5. Now remove the winch mounting plate and set aside. pg
4 6. Remove the pinch bolt on the U-Joint connecting the steering shaft to the rack and pinion. 7. Remove the 5 bolts that hold the rack housing to the frame. 8. To make removal of the OEM rack easier remove the four bolts securing the front differential and slide it forward. pg
5 9. Now remove the two sway bar bolts and let it hang. 10.With all the fasteners disconnected you can now pull down on the rack to disengage the u-joint from the pinion and remove the rack from the vehicle. pg
6 10. Install the new rack assembly in place of the old, making sure that your rack is centered. This can be seen by the mark on the pinion. Spline the u-joint onto the pinion and secure the rack into position using the hardware provided. Tighten the bolts to 40 ft lbs. 11. Install the thru bolt into the U- Joint connecting the lower shaft assembly and tighten to 40 ft lbs. Note: The steering shaft and the pinion spline have a blind tooth. They must be lined up in order to go together. pg
7 12. Place the new tie rod end on the steering arm making sure to mimic the old setup coming in from the top of the spindle. Install the rod end nut, and torque it to 35 ft lbs. 13. Reinstall winch plate and winch. Make sure the two power wires are on the correct posts and the controller plug is plugged in. 14. Measure from the same spots on your front tires and set your toe to what you had previously recorded. To adjust the toe, loosen the jam nut and turn the inner tie rod in or out as needed. Tighten the jam nut and make sure the steering wheel is centered. It may be necessary to remove the steering wheel and re-center it. You are now ready to drive. 15. Congratulations! Your Rackzilla is now installed! 1555 Enterprise Parkway Twinsburg OH /3/15 Copyright 2015 by Wicked Bilt. All rights reserved. No part of these materials can be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from Wicked Bilt. pg
Yamaha Viking Rackzilla Install/Removal
2014-15 Yamaha Viking Rackzilla Install/Removal Kit Numbers: 8001850, 8001790 Full refund will NOT be granted to any kits that are damaged, scratched, or altered in any fashion. Kit Contents: Part Number
More information60-72 Chevrolet C10 Power Rack & Pinion Kit Instructions # , , &
60-72 Chevrolet C10 Power Rack & Pinion Kit Instructions # 8011740-01, 8011900-01, & 8011920-01 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer
More informationFord Fairlane Rack & Pinion Kit Instructions #
1963-1965 Ford Fairlane Rack & Pinion Kit Instructions # 8011570 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any warranty
More informationWHEEL DRIVE GM S-SERIES TRUCKS & SUV S ( 82-95) & ( 96-04) &
1982-2004 2-WHEEL DRIVE GM S-SERIES TRUCKS & SUV S ( 82-95) 8000990-01 & 8000990-02 ( 96-04) 8001020-01 & 8001020-02 Unisteer offers a limited warranty against all manufacturer defects of their kits and
More informationFord Full-Size Rack & Pinion Kit Instructions #
1949-1951 Ford Full-Size Rack & Pinion Kit Instructions # 8011660 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any warranty
More information58-62 Corvette Manual Rack & Pinion Kit Instructions #
58-62 Corvette Manual Rack & Pinion Kit Instructions # 8001550 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any warranty
More informationFord Torino Small Block Rack Kit Instructions
1968-69 Ford Torino Small Block Rack Kit Instructions 8012290-01 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any warranty
More information*USE ONLY POWER STEERING FLUID IN SYSTEM. DO NOT USE ATF. YOU MUST USE THE SUPPLIED HEADERS, MODIFY EXHAUST PIPES, AND WELD FLANGES.
1949-1951 Ford Full-Size Rack & Pinion Kit Instructions # 8011660 Full refund will NOT be granted to any kits that are damaged, scratched, or altered in any fashion. *USE ONLY POWER STEERING FLUID IN SYSTEM.
More information67-70 Cougar Rack Kit Instructions # &
67-70 Cougar Rack Kit Instructions # 8011950-01 & 8011940-01 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any warranty on
More informationTRANS-AM POWER RACK AND PINION INSTALLATION INSTRUCTION MANUAL
1970-81 TRANS-AM POWER RACK AND PINION INSTALLATION INSTRUCTION MANUAL 8011160-01 & 8011110-01 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer
More informationG-Body Rack & Pinion Kit Instructions
1977-82 G-Body Rack & Pinion Kit Instructions 8012400-01 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any warranty on any
More informationPart # Description Qty Inspected By Rack & Pinion Pump Kit Remote Reservoir Line Kit Shaft Kit
58-62 Corvette Power Rack & Pinion Kit Instructions # 8011530 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any warranty
More information67-69 Camaro / Nova Power Rack & Pinion # ,
67-69 Camaro / 68-74 Nova Power Rack & Pinion # 8010540-01, 8010540-02 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any
More informationUNISTEER Performance Products
UNISTEER Performance Products 1965-Early 1967 Manual Mustang Install Manual 8001110-01 & 8001120-01 *ALTHOUGH THIS KIT IS FAIRLY SIMPLE TO INSTALL, SOME MODIFICATIONS MAYBE NECESSARY. *BEFORE STARTING
More informationUNISTEER Performance Products UNIVERSAL HOT ROD ELECTRA-STEER KIT
UNISTEER Performance Products UNIVERSAL HOT ROD ELECTRA-STEER KIT 8051500 BEFORE YOU START PLEASE READ! Designing steering systems requires an understanding of steering function and design. If you are
More information2. Remove front wheels.
1 PARTS DIAGRAM 2 Installation Instructions: (PASSENGER SIDE) 1. Place jack under center of RUV front end and lift until front wheels clear the ground. Be careful to support the RUV properly so that it
More information2014 F /6 LIFT KIT
92157500 2014 F-150 4 /6 LIFT KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions,
More information&
UNISTEER Performance Products 1968-72 CHEVROLET CHEVELLE POWER RACK AND PINION KIT INSTALLATION INSTRUCTION MANUAL 8010700-01 & 8010700-02 Thank you for purchasing Unisteer Performance Products for your
More informationOn-Vehicle Service Hub and Drum Assembly. Remove or Disconnect (Figures 1, 3-5) 1 of 8 11/25/2016 2:47 PM
1 of 8 11/25/2016 2:47 PM On-Vehicle Service Hub and Drum Assembly Remove or Disconnect (Figures 1, 3-5) Tools Required: J-35012 Rear Hub Bearing Nut Wrench J-35013 Rear Hub Remover 1. Remove the drain
More informationPRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Ford F150 4WD 4" Suspension Lift Kit
2015 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front Brake Line
More informationLIFT-506 BMF Lift Kit Club Car DS Gas & Electric Installation Instructions
LIFT-506 BMF Lift Kit Club Car DS Gas & Electric 2003.5-09 Installation Instructions Contents of LIFT-506 Club Car DS BMF Lift Kit: a (1 ea.) BMF Front Suspension b (1 ea.) Driver Side Upper A-Arm c (1
More informationRear Sway Bar for XC90 ( ) 2.5T and T6 ipd mounting kit SBK42
Dedicated to improving vehicle fun, safety & performance Installation Instructions Rear Sway Bar for XC90 (2003-0) 2.5T and T6 ipd mounting kit SBK2 PI-298 08/06 Thank you for purchasing this anti-sway
More information3.5 inch A-Arm Lift Kit
16-010 3.5 inch A-Arm Lift Kit will fit CLUB CAR PRECEDENT installation instructions included: Main Suspension Assembly 2 Spindles 2 A-Arms 2 Rear Shock Mounting Plates 2 Rear Lift Blocks 2 U-Bolts 1 2
More informationOnBoard Drum Major Podium
Assembly and Owner s Manual OnBoard Drum Major Podium CONTENTS CONTENTS................................................................................. 1 SAFETY...................................................................................
More informationINSTALLATION INSTRUCTIONS FOR FORD 4WD SUPER DUTY 6 SUSPENSION SYSTEM
INSTALLATION INSTRUCTIONS FOR 1999-2004 FORD 4WD SUPER DUTY 6 SUSPENSION SYSTEM Requires the following parts for a complete installation: Front Leaf Springs P/N 60SD6 Hardware Kit P/N 6000H Vehicle specific
More information05 12 TOYOTA TACOMA 2WD
MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714 630 0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: PARTS LIST K756864 6" LIFT KIT 05 12 TOYOTA TACOMA 2WD QTY SPINDLE,
More informationLIFT-507 BMF Lift Kit E-Z-Go RXV Gas or Electric Installation Instructions
LIFT-507 BMF Lift Kit E-Z-Go RXV Gas or Electric Installation Instructions Contents of LIFT-507 E-Z-Go RXV BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger
More information64-67 Chevelle. Power Rack & Pinion Cradle Kit
64-67 Chevelle Power Rack & Pinion Cradle Kit 64-67 Chevelle Note: For safety disconnect battery cables and ensure that the vehicle is properly supported by jack stands. Before painting or powder coating
More information*1557BAG12* 1557BAG F /5 /6 LIFT KIT G THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS.
2015-18 F-150 4 /5 /6 LIFT KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. 92155700G *1557BAG12* 1557BAG12 Rough Country recommends a certified technician install this system. In addition
More informationLIFT Standard A-Arm Lift Kit Club Car Precedent Installation Instructions
LIFT-563 6 Standard A-Arm Lift Kit Club Car Precedent Installation Instructions Contents of LIFT-563 Club Car Precedent Lift Kit: a (1 ea.) Front Suspension b (1 ea.) Driver Side Upper A-Arm c (1 ea.)
More information2014 F /6 LIFT KIT
92157500 2014 F-150 4 /6 LIFT KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions,
More informationPRORYDE ADJUSTABLE FRONT LIFT KIT INSTALLATION PATENTED
PRORYDE ADJUSTABLE FRONT LIFT KIT INSTALLATION CHEVROLET/GMC 2007-Up W/JL4 Electronic Suspension PATENTED IMPORTANT! Read ALL WARNINGS and information contained in these instructions PRIOR to installing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767 3100-3200 3 DROPPED FRONT SPINDLE 73-87 1/2 TON C-10 PICK-UP / 1/2 TON BLAZER
More information,
UNISTEER Performance Products 67-69 Camaro/ 68-74Nova Power Rack & Pinion 8010540-01, 8010540-02 (OPTIONAL -02 CHROME KIT SHOWN ABOVE) ALTHOUGH THIS KIT IS FAIRLY SIMPLE TO INSTALL SOME MODIFICATIONS ARE
More informationPARTS LIST: VIEWPOINT RUNNING BOARD NISSAN MURANO EXCLUDES 2dr CROSSCABRIOLET CONVERTIBLE
PARTS LIST: VIEWPOINT RUNNING BOARD Qty Description Qty Description 1 Driver/Left Running Board 14 10-1.5mm x 35mm Bolt Plates 1 Passenger/Right Running Board 6 10-1.50mm x 30mm Hex Bolt 1 Driver/Left
More informationINSTALLATION INSTRUCTIONS FOR FORD 4WD SUPER DUTY 2-1/2 SUSPENSION SYSTEM
INSTALLATION INSTRUCTIONS FOR 1999-2004 FORD 4WD SUPER DUTY 2-1/2 SUSPENSION SYSTEM Requires the following parts for a complete installation: Front Leaf Springs P/N 60SD25 Vehicle specific Box Kit depending
More informationSafety - Installation and Operation:
4x4 or 4x2 Instructions EZGO Electric Cars Thank you for purchasing your 4x4 or 4x2 conversion kit. Safety at all times whether during installation or operation is utmost importance. Before After!!!!!!!!!!!!!!
More informationFRONT DRIVELINE MODIFICATION MAY BE NECESSARY!!!!
INSTALLATION INSTRUCTIONS FOR 2009 DODGE 2500/3500 4WD & 1500 Mega Cab 6 SUSPENSION SYSTEM PART NUMBER 7206 Requires the following parts (sold separately) for a complete installation: Front Coil Spring
More informationCognito Motorsports, Inc., GM 2011-present 8-Lug truck Pitman/Idler Arm Support Kit SKU# PISK3008 **UTILITY PATENT US 7,475,891 B2**
Cognito Motorsports, Inc., GM 2011-present 8-Lug truck Pitman/Idler Arm Support Kit SKU# PISK3008 **UTILITY PATENT US 7,475,891 B2** Introduction - This application is for stock and lifted applications
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationUNISTEER Performance Products
UNISTEER Performance Products 1960-65 FALCON MANUAL RACK AND PINION INSTALLATION INSTRUCTION MANUAL 8001050-01 & 8001050-02 Thank you for purchasing Unisteer Performance Products for your 1960-65 Falcon/Comet.
More informationSteering Gear Replacement
Page 1 of 7 Steering Gear Replacement Removal Procedure Notice: With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column
More informationNISSAN TITAN XD NISSAN TITAN (LD) PATENTED
PRORYDE ADJUSTABLE FRONT LIFT KIT INSTALLATION 2016 + NISSAN TITAN XD 2017 + NISSAN TITAN (LD) PATENTED IMPORTANT! Read ALL WARNINGS and information contained in these instructions PRIOR to installing
More informationINSTRUCTION BULLETIN
INSTRUCTION BULLETIN No. 328288 Machine: M20/T20/M30/ S30 Published: 05-2011 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in
More informationParts List. Item Qty. Part # Description Item Qty. Part # Description Torque. 1 1 Bumper Replacement Shell 10 4 ½ x 1 ½ Hex Bolt 65 Ft.
Installation Instructions BR20 Rear Bumper Replacement Part # 28371T 2011-2016 Ford F-250 & F-350 Super Duty 2/4WD Do not attempt to install this product on any vehicle other than the one listed above!
More information58-62 Impala. Rack & Pinion Cradle Kit
58-62 Impala Rack & Pinion Cradle Kit 58-62 Impala Note: For safety disconnect battery cables and ensure that the vehicle is properly supported by jack stands. Before painting or powder coating of the
More information04-08 FORD F150 4 KIT
9257700 04-08 FORD F50 4 KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions, professional
More informationParts List ILLUSTRATION #1
Installation Instructions BR20 Rear Bumper Replacement Part Number 28171T 2014-2016 Chevrolet Silverado 1500 2/4WD Do not attempt to install this product on any vehicle other than the one listed above!
More informationMOTOALLIANCE WINCH MOUNT
, / 1-866-527-7637 www.motoalliance.com MOTOALLIANCE WINCH MOUNT Polaris Sportsman 600 & 700 Thank you for purchasing our MotoAlliance winch mount(s). You now own a premium custom winch mount to allow
More informationPRORYDE ADJUSTABLE FRONT LIFT KIT INSTALLATION 2014 CHEV/GMC. Patent Pending
PRORYDE ADJUSTABLE FRONT LIFT KIT INSTALLATION 2014 CHEV/GMC 2007-Up W/JL4 Electronic Suspension Patent Pending IMPORTANT! Read ALL WARNINGS and information contained in these instructions PRIOR to installing
More information5 inch Drop Axle Lift Kit
Revised December 2015 PART# 18143 included: 5 inch Drop Axle Lift Kit will fit E-Z-GO TXT installation instructions 1 2 Main Axle Assembly 2 Rear Lift Blocks 2 Rear Shock 2 Spacers 4 U-Bolts Mounting Plates
More information73-87 Chevy C-10 Rack and Pinion Conversion Kit
73-87 Chevy C-10 Rack and Pinion Conversion Kit For safety, disconnect battery cables and ensure that vehicle is properly supported by jack stands. NOTE: Power Steering Line Kit (FR1610) is sold separately
More informationSPECIAL TOOLS REQUIRED:
INSTALLATION INSTRUCTIONS FOR 2010-15 TOYOTA 4RUNNER WITH XREAS SUSPENSION 3 SUSPENSION LIFT KIT PART NUMBER 432X WARNING!!! READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE PROCEEDING. MAKE SURE THAT YOU HAVE
More informationWINCH MOUNT KIT FOR POLARIS RANGER P/N ASSEMBLY / OWNERS MANUAL. Application WINCH KIT NO. 25-9xxx
WINCH MOUNT KIT FOR POLARIS RANGER P/N 25-3300 ASSEMBLY / OWNERS MANUAL Application WINCH KIT NO. 25-9xxx Before you begin, please read these instructions and check to be sure all parts and tools are accounted
More informationINSTALLATION INSTRUCTIONS MKIV Toyota Supra Manual Rack Conversion
INSTALLATION INSTRUCTIONS MKIV Toyota Supra Manual Rack Conversion 1 Removal of Stock Rack 1.1 With your steering wheel centered, remove the pinch bolt from the factory intermediate shaft. This is located
More informationINSTALLATION INSTRUCTIONS FOR FORD 4WD SUPER DUTY F /2 COIL SPRING SUSPENSION SYSTEM
INSTALLATION INSTRUCTIONS FOR 2005-07 FORD 4WD SUPER DUTY F250-350 4 1/2 COIL SPRING SUSPENSION SYSTEM Requires the following parts (sold separately) for a complete installation: KIT PART NUMBER (6345
More informationINSTALLATION INSTRUCTION 88148
INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION
More information(800) MON-FRI 7AM-5PM PST OR WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times**
IF YOUR ReadyLIFT PRODUCT IS MISSING A OR HAS A DAMAGED PART, PLEASE CONTACT CUSTOMER SERVICE DIRECTLY. For warranty issues please return to the place of installation and contact ReadyLIFT. A NEW REPLACEMENT
More informationAlpha Series Front Bumper Installation Manual
1 K Alpha Series Front Bumper Installation Manual - 2003-2009 GM 4500-5500 2 Kelderman Alpha Series Front Bumper Winch Pre-Runner Bar Not Available - Contents - Kit Numbers. (3) - Introduction. (4) - Safety...
More informationLIFT-304 (3 ) and LIFT-104 (6 ) Drop Spindle Lift Kits Yamaha G22, Gas or Electric Installation Instructions
LIFT-304 (3 ) and LIFT-104 (6 ) Drop Spindle Lift Kits Yamaha G22, Gas or Electric Installation Instructions LIFT-304 LIFT-104 Contents of LIFT-304/104 Yamaha G22 Lift Kit: a (1 ea.) Passenger Side Spindle
More information5481 FRONT ANTI-SWAY BAR 10+ CHEVROLET CAMARO
INSTALLATION INSTRUCTIONS 5481 FRONT ANTI-SWAY BAR 10+ CHEVROLET CAMARO CONGRATULATIONS! You were selective enough to choose a BELLTECH PRODUCT. We have spent many hours developing our line of products
More informationSUBJECT: Radio Speaker Misdiagnosis - Rattle/Buzz Sounds in Door Modules
NUMBER: GROUP: DATE: Body March 20, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval
More informationINSTALLATION INSTRUCTIONS BULL BAR DODGE RAM 1500 PART # B-D1091;B-D2091
INSTALLATION INSTRUCTIONS PART # B-D1091;B-D2091 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Brackets (for trucks without tow hooks only) 8 12-1.75mm Hex Nuts
More informationINSTRUCTION S G-Comp Front Suspension: Chevy Camaro Speedway Motors, Inc Kit Contents:
INSTRUCTION S 350-500 G-Comp Front Suspension: 70-81 Chevy Camaro Speedway Motors, Inc. 2017 Kit Contents: 350500.1 G-Comp Subframe, Camaro 350500.2 G-Comp Sway Bar Kit, Camaro 350500.3 Hardware Kit, G-Comp
More informationInstallation Notes: #86000-R Race Series +3.5 L/T Kit
159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation
More information(800) MON-FRI 7AM-5PM PST OR WEBSITE: ReadyLIFT.COM **Please retain this document in your vehicle at all times**
IF YOUR ReadyLIFT PRODUCT IS MISSING A PART OR HAS A DAMAGED PART, PLEASE CONTACT CUSTOMER SERVICE DIRECTLY. A NEW REPLACEMENT PART WILL BE SENT TO YOU IMMEDIATELY (800)549-4620 MON-FRI 7AM-5PM PST OR
More informationLIFT-504. BMF Lift Kit. Yamaha G22 Gas or Electric. Installation Instructions
LIFT-504 BMF Lift Kit Yamaha G22 Gas or Electric Installation Instructions Contents of LIFT-504 Yamaha G22 BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger
More information04-08 FORD F150 6 KIT
957600 THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. 0-08 FORD F50 6 KIT Rough Country recommends a certified technician install this system. In addition to these instructions, professional
More informationWheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles
Rear Suspension Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles All-Wheel Drive (AWD) Vehicles Front Wheel Drive (FWD) Vehicles Removal All vehicles NOTICE: Suspension fasteners are critical
More informationParts List. Item Qty. Part # Description Item Qty. Description Torque
Installation Instructions BR20 Rear Bumper Replacement Part Number 28171T Chevrolet Silverado 1500 2/4WD Parts List Item Qty. Part # Description Item Qty. Description Torque 1 1 28171T0AA Bumper Replacement
More informationInstallations Instructions for Maier Racing Front Coilover Kit MS Ford Mustang
22215 Meekland Avenue Hayward, CA 94541 Phone: (510) 581-7600 Fax: (510) 581-2406 Installations Instructions for Maier Racing Front Coilover Kit MS-02-001 1964-1973 Ford Mustang Contents Front Coilover
More informationVibrator Kit. Stainless Steel & Poly Hopper Spreaders with FLEET FLEX Electrical System
October 1, 2016 Lit. No. 95098, Rev. 01 PARTS LIST Vibrator Kit Stainless Steel & Poly Hopper Spreaders with FLEET FLEX Electrical System 5 7 6 9 8 4 1 10 2 3 99504 1 Vibrator Kit Item Part Qty Description
More informationPart # GM F-Body Front TruTurn System GM F-Body TruTurn System. Table of contents. Installation Instructions
Part # 1119599-190-191 GM F-Body Front TruTurn System Recommended Tools 190-191 GM F-Body TruTurn System Installation Table of contents Page... Included components Page... Upper Control Arm Components
More information'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS
1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures
More informationInstallation manual. 4.5 suspension system June 2007 Dodge Ram 2500 / Part # Part # Important customer information:
Installation manual 4.5 suspension system 2003 - June 2007 Dodge Ram 2500 / 3500 Part # 34003 sj11407rev.03 Part # 34003 2003 - June 2007 Dodge Ram 2500 / 3500 4.5 suspension system Part # Description
More informationINSTALLATION INSTRUCTION 88581
INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES! WARNING: This suspension
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2100 DROPPED FRONT SPINDLE CHEVROLET 2WD S-10 / S-15 PICKUP / BLAZER / JIMMY, including models with ABS General Motors G-Body Rear Wheel Drive Cars CONGRATULATIONS! You were selective
More informationAlpha Series Front Bumper Installation Manual
1 K Alpha Series Front Bumper Installation Manual - 2017 Ford Super Duty 2 Kelderman Alpha Series Front Bumper Light Winch - Contents - Kit Numbers. (3) - Introduction. (4) - Safety... (5) - Bumper Removal......
More informationINSTALLATION INSTRUCTION 88094
INSTALLATION INSTRUCTION 88094 FOR RANCHO SUSPENSION SYSTEM RS6594B 4WD & 2WD NISSAN TITAN READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev D IMPORTANT NOTES! WARNING:
More informationHopper and Drive Components
Fisher Engineering 50 Gordon Drive, Rockland, Maine 04841 213 www.fisherplows.com 8001 1, 8004 1, 800 1 January 1, 201 Lit. No. 54, Rev. 02 Hopper and Drive Components POLY CASTER Hopper Spreader Parts
More informationINSTALLATION INSTRUCTIONS *When referring to left and right positions during the installation process, it is from the seated position*
1 PARTS DIAGRAMS 2 3 4 INSTALLATION INSTRUCTIONS *When referring to left and right positions during the installation process, it is from the seated position* FRONT LIFT INSTALLATION 1. Place a jack under
More informationInstallation Instructions BR20 Rear Bumper Replacement Part # 28178T Toyo ta Tundra 2/4WD
Installation Instructions BR20 Rear Bumper Replacement Part # 28178T 2014-2016 Toyo ta Tundra 2/4WD Excludes Models with B lind Spot Monitoring & Cross Traffic Alert Parts List Item Qty. Part # Description
More informationLIFT-503. BMF Lift Kit. Club Car Precedent. Installation Instructions
LIFT-503 BMF Lift Kit Club Car Precedent Installation Instructions Contents of LIFT-503 Club Car Precedent BMF Lift Kit: a (1 ea.) BMF Front Suspension b (1 ea.) Driver Side Upper A-Arm (Shipped Loose)
More informationMarlon Xplore SxS Deck Owner s Manual Assembly & Installation Instructions
Marlon Xplore SxS Deck Owner s Manual Assembly & Installation Instructions 2850lbs load max on deck 2500lbs load max on ramps Marlon Recreational Products www.marlonproducts.com 1-800-663-7367 IMPORTANT
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2505 Lowering Spindle Assembly Installation Instructions ½ TON SILVERADO
More informationSpreader and Vehicle Battery Kits
March 1, 2013 Lit. No. 94879, Rev. 11 and Vehicle Battery Kits Hopper s Parts Lists and Installation Instructions Read this document before installing the and Vehicle Battery Kit. Use standard methods
More informationINSTALLATION MANUAL 4 I.F.S. SUSPENSION CURR. CHEVY SUBURBAN / YUKON XL (WITH 5 LINK REAR END) PART # 14965
PART NUMBER : 14965 2000 CURR. SUBURBAN W/ REAR COIL SPRINGS 4 SUSPENSION SYSTEM WITH FRONT SPINDLES PARTS LIST: Part # Description Qty. C4I1SN-07 Passenger Side Differential Drop 1 C4I1SN-23 Driver Side
More informationFlaming River Ind. 800 Poertner Dr Berea, OH Impala Rack and Pinion Conversion Kit
Flaming River Ind. 800 Poertner Dr Berea, OH 44017 800-648-8022 58-64 Impala Rack and Pinion Conversion Kit For safety, disconnect battery cables and ensure that vehicle is properly supported by jack stands.
More informationPRORYDE ADJUSTABLE FRONT LIFT KIT INSTALLATION 2014 CHEV/GMC PATENTED
PRORYDE ADJUSTABLE FRONT LIFT KIT INSTALLATION 2014 CHEV/GMC 2007-Up W/JL4 Electronic Suspension PATENTED IMPORTANT! Read ALL WARNINGS and information contained in these instructions PRIOR to installing
More informationINSTALLATION INSTRUCTION 88146
INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING
More informationINSTALLATION MANUAL TOYOTA TACOMA 5 SUSPENSION SYSTEM PART # 54900
PART NUMBER : 54900 1996 2004 TOYOTA TACOMA 5 SUSPENSION SYSTEM PARTS LIST: Part # Description Qty. 55900-01 Driver Side Spindle 1 55900-02 Passenger Side Spindle 1 54900-01 Rear brake proportioning valve
More informationINSTALLATION INSTRUCTIONS PART # 9B048803SS/9B048803A SIDE BAR FOR FORD ESCAPE 2013
INSTALLATION INSTRUCTIONS PART # 9B048803SS/9B048803A SIDE BAR FOR FORD ESCAPE 2013 PARTS LIST: - Qty Description Qty Description 1 Driver / Left Sidebar 2 12mm Plastic Retainers 1 Passenger / Right Sidebar
More informationInstruction set # 7068 Cognito Motorsports, Inc. Upper Control Arm Leveling Kit for GM 8-Lug #UCAK (Boxed Style)
Cognito Motorsports, Inc. Upper Control Arm Leveling Kit for 2001-2010 GM 8-Lug #UCAK100010 (Boxed Style) Introduction - These control arms will not affect the height of the truck, the height is determined
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationINSTALLATION INSTRUCTIONS 88518
INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:
More information6 inch a-arm lift kit
PART# 18144 included: 6 inch a-arm lift kit WILL FIT YAMAHA DRIVE installation instructions Main Bracket Tie Rod Extensions Shock Mount Brackets Stiffener Bracket Rear Bracket Sway Bar Bracket WARNING:
More informationPARTS LIST INCLUDED IN KIT TORQUE SPECIFICATIONS PRODUCT SAFETY LABEL MUST BE INSTALLED INSIDE CAB IN PLAIN VIEW OF ALL OCCUPANTS.
INSTALLATION INSTRUCTIONS FOR 2010-15 TOYOTA 4RUNNER SR5 AND SPORT (Non-Air Leveling & Non-X-REAS) AND FOR 2010-14 TOYOTA FJ CRUISER 2WD & 4WD 3 SUSPENSION LIFT KIT PART NUMBER 432 WARNING!!! READ AND
More informationINSTALLATION INSTRUCTIONS FOR 2016 TOYOTA TACOMA 4 X 4 AND PRE RUNNER 3 SUSPENSION LIFT KIT PART NUMBER
INSTALLATION INSTRUCTIONS FOR 2016 TOYOTA TACOMA 4 X 4 AND PRE RUNNER 3 SUSPENSION LIFT KIT PART NUMBER 427 WARNING!!! READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE PROCEEDING. MAKE SURE THAT YOU HAVE ALL
More informationWINCH MOUNT KIT FOR POLARIS RANGER P/N ASSEMBLY / OWNERS MANUAL. Application WINCH KIT NO. 25-9xxx
WINCH MOUNT KIT FOR POLARIS RANGER P/N 25-3370 ASSEMBLY / OWNERS MANUAL Application WINCH KIT NO. 25-9xxx Before you begin, please read these instructions and check to be sure all parts and tools are accounted
More informationINSTALLATION INSTRUCTIONS. FD3S RX7 Manual Rack Conversion
INSTALLATION INSTRUCTIONS FD3S RX7 Manual Rack Conversion 1 Removal of Stock Rack 1.1 With your steering wheel centered, remove the pinch bolt from the factory intermediate shaft lower knuckle. If you
More information