Pressure. Pressure. Mechanical. Press. Switches

Transcription

1 Pressure Pressure Mechanical Press. Switches

2 Contents Mechanical Pressure Switches 4 Introduction 4 Metal Diaphragm 6 Bourdon Tube 7 Compact 8 Diaphragm Seal Piston Summary Mechanical Pressure Switches 12 Metal Diaphragm Pressure Switches 18 Type D1S-.../D2S Type D1T-.../D2T Type D1X-.../D2X Metal Diaphragm Diff. Press. Switches 24 Type DPD1T-.../DPD2T Bourdon Tube Pressure Switches 26 Type B1S-.../B2S Type B1T-.../B2T Type B1X-.../B2X-... 0

3 Contents Pressure Diaphragm Seal Piston Press. Switches 2 Type E1S Type E1H Type P1H Type P1X Type MSPS Compact Pressure Switches 42 Type 9671X / 9681X 42 Type 9692X 44 Type Series Type Series Type KLK-.../KLM Type KD Mechanical Pressure Switches 54 ccessories 54 Certificates 55

4 Mechanical Pressure Switches Introduction pplications Mechanical pressure switches, also known as hydro-electric pressure monitors, are used to connect or disconnect electric circuits. pressure switch can serve as a control unit and as an optical or acoustic monitor or indicator. pressure switches are chiefly used in hydraulic systems for monitoring minimum pressures, such as protecting pumps from dry operation or as protection for oil lubrication systems. They can also be used for monitoring maximum pressures, such as automatic switch-off or warning device before a pressure relief valve reaches its limit pressure (fig. 1). nother application for pressure switches is the control of storage loading processes. fter the storage capacity is reached (Pmax) the flow is stopped and the pump shuts down. When the storage pressure drops below a defined minimum value (Pmin), the pump is automatically started again. The switch hysteresis (Pmax Pmin) can be freely selected with two pressure switches and one solenoid valve (fig. 2). Within certain pressure ranges the storage process can be controlled with only one pressure switch, the KD1 compact pressure switch which specifically designed for this application. The pressure set points Pmax and Pmin are factory set according to your requirements. Life Span and ccuracy The life span and accuracy of pressure switches depend on the frequency and peaks of pressure changes, the number of load cycles and temperature influences. For proportional operation pressure switches the highest accuracy is achieved above 70 %, the longest life span below 0 % of the performance range (fig. ). The best combination of life span and accuracy is, however, between 0% and 70% of the performance range. Contact Materials pressure switches have silver contact micro switches. On request we also supply micro switches with gold-plated contacts. Gold-plated are almost exclusively used on micro switches that are only exposed to low electrical loads. Fig. 4 depicts the standard values for the use of silver or goldplated contacts. We are happy to assist you in the selection of the material best suited for your application. Summary: The product of current and voltage should not exceed 0.12 V. Recommended values: current should range at < 400 m and voltage at < 0 V. If operated on alternating current the above values are peak values. Contact Protection The micro switches (MS) used in the pressure switches are normally suitable for both direct and alternating current operation. Inductive, capacitive and lamp loads may, however, considerably reduce the life span of a micro switch and, under extreme circumstances, even damage the contacts. Fig. 1 Fig. 2 Pressure ccuracy Life Span Fig. V Pmax + xbar Pmax Pmin Pmin Pmax Pmin p Pmax p +24V K1 K1 K1 djustment ranges 0% 70% 0% satisfactory good excellent excellent good satisfactory Silver contacts Gold-plated contacts m 00m Fig. 4: Range of application of the various contact materials

5 Pressure Mechanical Pressure Switches Introduction Capacitive Loads and Lamp Loads Capacitive and lamp loads may be accompanied by very high discharge rates or start-up current rushes 15 times higher than the rated value. Under such circumstances, current limiters (for instance a protective resistance) should be used (fig. 5 and 6). Inductive Loads High inductive peak loads during disconnection may considerably reduce the life span of a micro switch. The electric circuit can be protected by following the wiring diagram in figure 7 and 8. The ratings of the individual elements (diode, varistor etc.) are determined by the corresponding application. Pulsation and Vibrations within the System? How to remedy the problem: Pulsation and vibrations within the system can affect the function of the pressure switch. There are two different types of pressure switches: one type is sufficiently protected against pulsation and vibrations occurring during operation due to its solid design, the others are designed for precision adjustment which, consequently, makes them more sensitive to such influences. Please refer to the summary for compact pressure switch values regarding vibration resistance. To ensure proper functioning of the pressure switch, please observe the following recommendations: Mechanical Vibrations Use rubber buffers between units and wall for wall mounted units. Pulsation/Vibration of the Medium Use flexible hoses instead of pipes. If this is technically not possible, place "pulsation restrictors" in front of the pressure switch, for example: helical pipes commercial pulsation snubbers diaphragm accumulators s air pockets can enhance pulsation, please ensure that the hydraulic system is properly vented. R1 MS C cable Fig. 5: Protection in case of capacitive loads R1 - Protection against start-up current rushes R2, R - Protection against high discharge currents MS R R2 Load MS Fig. 6: Lamp load provided with resistance in parallel or series connection to switch U = Fig. 7: Protection in case of continuous current and inductive load by recovery diode U ~ MS MS Diode R R Load C R Load Fig. 8: Protection in case of alternating current and inductive load by RC-link

6 Mechanical Pressure Switches Metal Diaphragm Metal diaphragm pressure switches with direct-acting pressure sensor and the snap-acting micro switch provide very high accuracy and long life span. pplications Machine and tool engineering, utoclave, Pump control, Refrigerant monitoring, Petrochemical industry, Process technology, Filter monitoring, Hydraulic power units djustment ranges bar Summary of main components Item 1: Item 2: Item : Item 4: Item 5: Item 6: Item 7: pprovals Fine-pitch screw allows precise set point adjustment Various housing types allow many applications in normal and hazardous installations; also Exi, Exd and UL Large variety of micro switches with different accuracy and switching voltages Wetted parts: DT: /1.4564/14568* DPDT: luminium/1.4504/1.4564/1.4568* * = (17.7-PH) Pressure connections with NPT thread Stainless steel diaphragm Differential pressure switches: two bellows for sealing without friction For approvals and options please refer to the summary below. D-Series 6 5 DPD-Series

7 Pressure Mechanical Pressure Switches Bourdon Tube Bourdon tube pressure switches with direct-acting pressure sensor and the snap-acting micro switch provide very high accuracy and long life span. pplications Pump control, Die-casting machines, Press control, Power plants, Petrochemical industry, Process technology djustment ranges bar Summary of main components Item 1: Item 2: Item : Item 4: Item 5: pprovals Various housing types allow many applications in normal and hazardous installations; also Exi, Exd and UL Large variety of micro switches with different accuracy and switching voltages Fine-pitch screw allows precise set point adjustment Several pressure ranges allow set points between 4.8 and 950 bar Pressure connections with NPT thread, for proof pressure > 500 bar; high pressure thread Wetted parts made of stainless steel For approvals and options please refer to the summary below. B-Series

8 Mechanical Pressure Switches Compact Pressure switches with a diaphragm or piston-type springloaded pressure element and snap-acting micro switch are characterized by their compact design. pplications OEM applications, Mobile and industrial hydraulic and pneumatic systems, Test bed and apparatus engineering, Heavy industry djustment ranges Series 8000: bar Series 9000: bar Summary of main components Item 1: Item 2: Item : Item 4: Item 5: pprovals High-accuracy micro switch. Silver or gold-plated contacts dependent on the application-specific requirements. pprovals: Exi Housing parts made of stainless steel and aluminium. Elastomer diaphragm or low-friction piston seal Same housing design for diaphragm and piston types allow many applications. Various pressure ranges allow precise setting between 0.6 and 600 bar or bar respectively. djustment of set points through hexagon socket (5mm). Option: factory set individual set points. For approvals and options please refer to the summary below. Series Serie

9 Pressure Mechanical Pressure Switches Compact Pressure switches with a diaphragm or piston-type springloaded pressure element and snap-acting micro switch are characterized by their compact design. pplications Mobile hydraulics, Motor control, Hydraulic clamping, Building and agricultural machines, Brake system control, Hydraulic accumulator control djustment ranges KLM: bar KLK: bar KD1: bar Summary of main components Item 1: Item 2: Item : Item 4: Item 5: pprovals KD1 and KL series only available with factory setting, unauthorized adjustment excluded. Silver and gold-plated contacts for KD1 series. pprovals KLM/KLK: Exi Same housing design for diaphragm and piston types allow many applications. Elastomer diaphragm or low-friction piston seal Housing parts made of stainless steel and aluminium or of stainless steel and brass or stainless steel. KLM/KLK: High-accuracy micro switch. Silver or gold-plated contacts dependent on the application-specific requirements. KD1: djustable hysteresis For approvals and options please refer to the summary below. KLM/KLK KD

10 Mechanical Pressure Switches Diaphragm Seal Piston Due to their design diaphragm seal piston pressure switches provide high accuracy, long life span and high proof pressure. pplications Hydraulic/pneumatic systems, Shipbuilding applications, Machine and tool engineering, Dosing machines, plant engineering, Sprinkler control djustment ranges bar Summary of main components Item 1: Item 2: Item : Item 4: Item 5: Item 6: Large variety of micro switches with different accuracy and switching voltages. Wetted parts: Diaphragm: NBR, FKM or PTFE (E-Series + EPDM, CR) Fitting: aluminium, polysulfone, (stainless steel), or nickel-plated aluminium Pressure connections with NPT or G threads Fine-pitch screw allows precise set point adjustment Several pressure ranges allow following set points: E series: bar P series: bar MSPS series: bar For many applications in normal and hazardous installations; also Exi and explosion proof housing acc. to CS and UL. Visual indication of set point for E1S and E1H Special Functions Type E1H can be equipped with manual reset for alarm functions with G-Micro switch option. Type E1S and E1H are available with R-Micro switch for adjustable hysteresis (adjustable deadband). pprovals For approvals and options please refer to the summary below. P-Series 5 4 E-Series 1 6 %

11 Pressure Mechanical Pressure Switches 11

12 Summary Mechanical Pressure Switches Model D1S, D2S / D1T, D2T D1X / D2X DPD1T / DPD2T Measuring element Stainless steel diaphragm Stainless steel diaphragm Stainless steel diaphragm Features pplications djustment ranges djustable switch contacts for vacuum and overpressure Machine-tool industry, autoclave, pump control, refrigerant monitoring bar up to bar djustable switch contacts for vacuum and overpressure Petrochemicals industry, process technology bar up to bar Number of contacts 1 or 2 1 or 2 1 or 2 Max. switch frequency/min ccuracy ±1 % ±1 % ±1 % djustable switch contacts for vacuum and overpressure Filter monitoring, hydraulic power units bar Temperature range -40 C C -40 C C -40 C C Vibration tolerance satisfactory satisfactory satisfactory Process connection (without adaptor) Electrical connection: 1/4 NPT female, 1/2 NPT female, stainless steel D1S, D2S: lead wires, PVC 1.5 mm 2 D1T, D2T: Cable gland 1/4 NPT female, 1/2 NPT female, stainless steel Terminal strip 1/8 NPT female, stainless steel Cable gland, plug DIN EN (prev. DIN 4650) Form Max. electrical rating up to 480 V C / V DC acc. to TEX up to 480 V C / V DC Options Housing Protection class Gold-plated contacts, hermetically sealed contacts D1S, D2S: without D1T, D2T: aluminium D1S, D2S: IP00 D1T, D2T: IP65 Gold-plated contacts, hermetically sealed contacts luminium, pressure proof pprovals Exi Exi and Exd, UL Exi IP65 Gold-plated contacts, hermetically sealed contacts luminium IP65 Catalog page D1S, D2S: 22 D1T, D2T:

13 Summary Mechanical Pressure Switches Model B1S, B2S / B1T, B2T B1X / B2X E1S Measuring element Bourdon tube Bourdon tube Plastic diaphragm / piston Features pplications djustable switch contacts, for high pressure Pump control, die-casting machines, press control, power plants djustable switch contacts, for high pressure Petrochemicals industry, process technology djustable switch contacts, for vacuum and overpressure Machine-tool industry, dosing machines, plant engineering, lubricant monitoring djustment ranges bar bar bar up to bar Number of contacts 1 or 2 1 or 2 1 Max. switch frequency/min ccuracy ±1% ±1% ±2% Temperature range -40 C C -40 C C -0 C C Vibration tolerance satisfactory good good Process connection (without adaptor) Electrical connection 1/4 NPT female, high pressure G 1/4 female, stainless steel B1S, B2S: lead wires, PVC 1.5 mm 2 B1T, B2T: cable gland, plug DIN EN (prev. DIN 4650) 1/4 NPT female, high pressure G 1/4 female, stainless steel Terminal strip 1/4 NPT female, 1/8 NPT female, 1/2 NPT male, G 1/4 female, aluminium / polysulfone / stainless steel Screw terminals Max. electrical rating up to 480 V C / V DC acc. to TEX up to 480 V C / V DC Options Housing Protection class Gold-plated contacts, hermetically sealed contacts B1S, B2S: without B1T, B2T: aluminium B1S, B2S: IP00 B1T, B2T: IP65 Gold-plated contacts, hermetically sealed contacts luminium, pressure proof pprovals Exi Exi and Exd, UL Exi Catalog page B1S, B2S: 28 B1T, B2T: 0 IP65 Gold-plated contacts, adjustable hysteresis without IP

14 Summary Mechanical Pressure Switches Model E1H P1H P1X Measuring element Elastomer diaphragm / piston Elastomer diaphragm / piston Elastomer diaphragm / piston Features pplications djustment ranges djustable switch contacts, for vacuum and overpressure Machine-tool industry, dosing machines, plant engineering, sprinkler control bar up to bar djustable switch contacts, rugged housing Hydraulic / pneumatic power units, shipbuilding applications djustable switch contacts Hydraulic / pneumatic power units, shipbuilding applications bar bar Number of contacts Max. switch frequency/min ccuracy ±2% ±2% ±2% Temperature range -0 C C -0 C C -0 C C Vibration tolerance good good good Process connection (without adaptor) Electrical connection 1/4 NPT female, 1/8 NPT female, 1/2 NPT male, G 1/4 female, luminium / polysulfone / stainless steel Plug DIN EN (prev. DIN 4650) Form 1/4 NPT female, 1/2 NPT female, aluminium or stainless steel Cable gland, plug DIN EN (prev. DIN 4650) Form 1/4 NPT female, 1/2 NPT female, aluminium or stainless steel Cable gland Max. electrical rating up to 480 V C / V DC up to 480 V C / V DC up to V C / V DC Options Gold-plated contacts, manual reset, adjustable deadband Gold-plated contacts, hermetically sealed contacts Gold-plated contacts, hermetically sealed contacts Housing luminium, cap polycarbonate or stainless steel luminium luminium Protection class IP65 IP65 IP65 pprovals Exi Exi, Nace Exi and Exd, CS, UL, Nace Catalog page

15 Summary Mechanical Pressure Switches Model MSPS 9671X / 9681X 9692X Measuring element Elastomer diaphragm / piston Elastomer diaphragm / piston Elastomer diaphragm / piston Features pplications Compact construction, adjustable switch contacts, via adjustment screw ir conditioning ventilation control steam ejectors Compact construction, adjustable switch contacts, via adjustment wheel, Ex vers. acc. to TEX Process industry, petrochemical plants, machine tool industry, compressors djustment ranges bar bar up to bar Compact construction, adjustable switch contacts, via adjustment wheel, Ex vers. acc. to TEX Process industry, petrochemical plants, machine tool industry, compressors bar Number of contacts 1 1 switch contact 1 switch contact Max. switch frequency/min ccuracy ±2% ±2% ±2% Temperature range -5 C C -0 C C -0 C C Vibration tolerance good good good Process connection (without adaptor) 1/8 NPT male, stainless steel 1/4 NPT female 1/4 NPT female Electrical connection Spade connectors Leads 450 mm PVC, conduit connection 1/2 NPT male Max. electrical rating up to V C / 125 V DC up to V C / 125 V DC acc. to TEX Options switching contact with DPDT function, gold-plated contacts Housing without Stainless steel, explosion proof enclosure Leads 450 mm PVC, conduit connection 1/2 NPT male up to V C / 125 V DC acc. to TEX 1 switching contact with DPDT function, gold-plated contacts Stainless steel, explosion proof enclosure Protection class IP00 IP65 IP65 pprovals Exi Exi and Exd, UL, CS, TEX Exi and Exd, UL, CS, TEX Catalog page

16 Summary Mechanical Pressure Switches Model Series 8000 Series 8000 Series 9000 Measuring element Elastomer diaphragm Steel piston Steel piston Features pplications Compact construction, djustable switch contact OEM applications, mobile- and industrialhydraulics and pneumatics, test bed and apparatus engineering, heavy industry Compact construction, djustable switch contact OEM applications, mobile- and industrialhydraulics and pneumatics, test bed and apparatus engineering, heavy industry djustment ranges bar bar bar Number of contacts Max. switch frequency/min ccuracy ±2% ±1% ±2% Compact construction, djustable switch contact OEM applications, mobile- and industrialhydraulics and pneumatics, test bed and apparatus engineering, heavy industry Temperature range -20 C C -40 C C -20 C C Vibration tolerance good good good Process connection (without adaptor) Electrical connection CETOP 40 x 40 mm Plug DIN EN (prev. DIN 4650) CETOP 40 x 40 mm Plug DIN EN (prev. DIN 4650) Plug DIN EN (prev. DIN 4650) Max. electrical rating up to V C / V DC up to V C / V DC up to V C / 24 V DC Options Gold-plated contacts, various process and electrical connections Gold-plated contacts, various process and electrical connections --- Housing luminium or stainless steel luminium or stainless steel luminium Protection class IP65 IP65 IP65 pprovals GL, Exi, culus GL, Exi, culus GL, Exi Catalog page

17 Summary Mechanical Pressure Switches Model KLM KLK KD1 Measuring element Elastomer diaphragm Steel piston Steel piston Features pplications Compact construction, factory set switch contacts Mobile hydraulics, motor control, hydraulic clamping Compact construction, adjustable factory set switch contacts Mobile hydraulics, Motor control, hydraulic clamping Compact construction, adjustable factory set switch contacts Building and agricultural machines, brake system control, hydraulic accumulator control djustment ranges 1... to 40 bar 0... to 400 bar 0... to 00 bar Number of contacts Max. switch frequency/min ccuracy ±2% ±1 % ±1 % Temperature range -20 C C -40 C C -40 C C Vibration tolerance excellent excellent excellent Process connection (without adaptor) Electrical connection M12 x 1.5 male G 1/4 male, stainless steel Cable gland with cable, plug DIN EN (prev. DIN 4650) Form C M12 x 1.5 male G 1/4 male, brass Cable gland with cable, plug DIN EN (prev. DIN 4650) Form C M12 x 1.5 male, brass Spade connector, cable gland with cable Max. electrical rating up to 60 V C / 60 V DC up to 60 V C / 60 V DC up to 60 V C / 60 V DC Options Gold-plated contacts, high pressure version, up to 150 bar Gold-plated contacts Gold-plated contacts, large hysteresis Housing Stainless steel Stainless steel and brass Stainless steel and brass Protection class Plug IP65, cable IP67 Plug IP65, cable IP67 Plug IP65, cable IP67 pprovals Exi Exi Exi Catalog page

18 Metal Diaphragm Pressure Switches Type D1S-.../D2S-... Mechanical single/dual pressure switch Repeatability ±1.0 % at constant temperature Features Metal diaphragm pressure switch Wettet parts welded. Direct action, no friction, high accuracy djustment ranges bar and bar (Vacuum) pplications Machine and tool engineering, utoclaves, Pump control, Refrigerant monitoring Technical Data Wetted parts: Repeatability: Switching rate: Stainless steel 17-7PH/SS04 ±1 % at constant temperature max. 20/min Temperature range: -40 C C Protection class: Housing: Process connection: IP00 Without housing for installation in control panels 1/4" NPT female thread Optional: 1/2" NPT female thread (P2) Electrical connection: Lead wire PVC 1.5 mm 2, length appr. 450 mm s Overpressure djustment range [bar] Electrical ratings and hysteresis: Weight: Set point adjustment: pproval: --- Max. operating pressure [bar] Proof pressure [bar] large variety of micro switches offers different electrical ratings and hysteresis for many applications. D1S-...: approx. 0.6 kg D2S-...: approx. 0.7 kg Turn the adjustment screw clockwise to decrease the set point Max. hysteresis of switch types in bar (end of range) Increasing press. Decreasing press. (short term) H, GH [bar] M, GM [bar] 2SS SS SS SS SS Vacuum SS SS

19 Pressure Metal Diaphragm Pressure Switches Type D1S-.../D2S-... Dimensions (in mm / inch) 45 approx. 7/0.28 approx. 55/2.17 leads approx. 450/17.72 long 48/ /1.1 Electrical ratings Micro switch H M approx. 95/.74 Special features Micro switch with silver contacts Micro switch with silver contacts 6/0.24 Process connection 29/ / 1.81 Mounting bore ø 5/ /2,28 Volt C 50/60 Hz * * D1S... 45/ /1.77 NC NC 90/.54 C NO C NO at vacuum NC/NO vice versa À Á 90/.54 Wiring for all types (contact status at atmospheric pressure) Volt DC 6 to D2S... 45/ 1.77 djustment screw slotted nut hex 8 /0.9 45/1.77 Circuit Á Power circuit À C=purple NC=blue NO=red /.54 Circuit À /0.9 Power circuit Á C=brown NC=orange NO=black Comments Small hysteresis; High C / low DC loads Medium hysteresis; High C and DC loads GH Micro switch with gold Small hysteresis GM contacts for low voltage and low current Medium hysteresis * on request Options P2 = 1/2" NPT F SS Process connection Ordering Example for order number Type Micro switch Options D1S or D2S H SS P2 90/.54 Your order number Type Micro switch or Options 19

20 Metal Diaphragm Pressure Switches Type D1T-.../D2T-... Mechanical single/dual pressure switch Repeatability ±1.0 % at constant temperature Features Metal diaphragm pressure switch Wetted parts welded. Direct acting, no friction, high accuracy djustment ranges bar and bar (Vaccum) pplications Machine and tool engineering, utoclaves, pump control, Refrigerant monitoring, chemical industry Ship building applications Technical Data Wetted parts: Repeatability: Switching rate: Stainless steel 17-7PH / SS04 ±1 % at constant temperature max. 20/min Temperature range: -40 C C Protection class: Housing: Process connection: Electrical connection: s Overpressure IP65 powder coated aluminium 1/4" NPT female thread Optional: 1/2" NPT female thread (P2) WGO terminal and cable gland M20 x 1.5; clamping range ø mm djustment range [bar] Electrical load capacity and hysteresis: Many micro switch versions with different switching powers and hysteresis are available and make it possible to make customized changes. Weight: D1T-...: approx. 1.0 kg D2T-...: approx. 1.1 kg Set point adjustment: Intrinsically safe: pproval: --- Max. operating pressure [bar] Proof pressure [bar] Turn the adjustment screw clockwise to decrease the set point The switches are also available for intrinsically safe applications. dd "Exi" in case of ordering. Maximum rating according to TEX: Umax = 28 V Imax = 50 m Max. hysteresis of the different switches in bar (end of range) Increasing press. Decreasing press. (short term) H, GH [bar] M, GM [bar] 2SS SS SS Specifications are subject to changes without notice. Index: F 80SS SS Vacuum SS SS

21 Pressure Metal Diaphragm Pressure Switches Type D1T-.../D2T-... Dimensions (in mm / inch) Specifications are subject to changes without notice. Index: F 120/4.72 M20 x 1.5 plug 2 pieces supplied free of charge with switch Electrical ratings Micro switch H M 57/ / /5 Special features Micro switch with silver contacts Micro switch with silver contacts Supplied with 1/2" NPT Volt C 50/60 Hz Cable gland M20 x 1.5 (clamping range ø mm) in scope of supply 46/ /.54 Set screw(s) under the cover Process connection 1/4" NPT internal Volt DC 6 to Switching- and connection diagram for all types (pressureless) Power circuit À C=lila NC=blue NO=red NC NC c NO c NO at vacuum NC/NO vice versa Power circuit Á C=brown NC=orange NO=black À Á Comments Small hysteresis; High C-/ low DC-load Medium hysteresis; High C- and DC-loads GH Micro switch with gold-plated Small hysteresis GM contacts for low voltage and/or low current Medium hysteresis Options Ordering Example for order number D1T-... ST1 Plug, -pin + E, DIN EN (prev. DIN 4650) ST Plug, 6-pin + E, DIN 4651 ST2 mphenol plug 4-pin + E EXI for intrinsically safe application EXI Type for intrinsically safe application Micro switch 480 V C and 15 only upon request D2T-... Options pproval D1T or D2T H SS ST2 EXI Your order number Type Micro switch Options or pproval 21

22 Metal Diaphragm Press. Switches Type D1X-.../D2X-... Mechanical single/dual pressure switch Repeatability ±1.0 % at constant temperature Features Metal diaphragm pressure switch Wetted parts welded. Direct action, no friction, high accuracy djustment ranges bar and bar (Vacuum) pplications Petrochemical industry, Process technology Technical Data Wetted parts: Repeatability: Switching rate: Stainless steel 17-7PH/SS04 ±1 % at constant temperature max. 20/min Temperature range: -40 C C Protection class: Housing: Process connection: IP65 Explosion proof housing, aluminum anodized and lacquered 1/4" NPT female thread Optional: 1/2" NPT female thread (P2) Electrical connection: Internal terminal strip ( mm 2 ), approved cable gland has to be provided by the customer Electrical ratings and hysteresis: s Overpressure large variety of micro switches offers different electrical ratings and hysteresis for many applications. djustment range [bar] Weight Set point adjustment: Intrinsically safe: D1X-...: approx. 2.7 kg D2X-...: approx. 2.8 kg Turn the adjustment screw clockwise to decrease the set point The switches are designed for intrinsically safe applications. Please add "Exi" to your ordering details when placing an order. To comply with the intrinsically safe approval following max. ratings must not be exceeded: Umax = 28 V Imax = 50 m pproval: Ex: Ex d II C T6 acc. to TEX culus: Class I, Groups B, C, D Class II, Groups E, F, G Max. operating pressure [bar] Proof pressure [bar] acc. to Underwriter Laboratories Inc. and Canadian Standard ssn. Max. hysteresis of switch types in bar (end of range) Increasing press. Decreasing press. (short term) H, GH [bar] M, GM [bar] SS SS SS SS Vacuum SS SS

23 Pressure Metal Diaphragm Press. Switches Type D1X-.../D2X-... Dimensions (in mm / inch) 197/7.756 Terminal 120/ /2 Wiring for all types (contact status at atmospheric pressure) NC NC 45 C NO C NO 51/ 2.01 at vacuum NC/NO vice versa Electrical ratings Micro switch H M À Á 71/ Mounting bore ø 8.5/0.5 ø 8/1.496 Process connection 1/4" NPT Special features Micro switch with silver contacts Micro switch with silver contacts Conduit connection 1/2" NPT Ground connection Power circuit À C=purple NC=blue NO=red 166/6.55 Volt C 50/60 Hz * * 21/ D1X / /.0 2/ Power circuit Á C=brown NC=orange NO=black djustment screw 11/ 0.4 Conduit connection 1/2" NPT ø 125/4.92 Process connection 1/4" NPT Volt DC 6 to D2X... Conduit connection /4" NPT 11/ 0.4 2/ / / pproval djustment screws: Power circuit À Power circuit Á 166/6.55.5/0.41.5/ / / 0.4 Process connection 1/4" NPT Conduit connection 1/2" NPT Comments Small hysteresis; High C / low DC loads Medium hysteresis; High C and DC loads GH Micro switch with gold-plated Small hysteresis GM contacts for low voltage and/or low current Medium hysteresis * on request Ordering Example for order number EX UL EXI Options Ex d approval culus approval Ex i approval Type Micro switch Options pproval D1X or D2X H SS P2 EX ø 125/4.92 P2 = 1/2" NPT F SS Process connection Your order number Type Micro switch Options or pproval 2

24 Metal Diaphragm Diff. Press. Switches Type DPD1T-.../DPD2T-... Mechanical single/dual pressure switch Repeatability ±1.0 % at constant temperature Features Metal diaphragm pressure switches Wetted parts welded. Direct action, no friction, high accuracy djustment ranges bar, differential pressure pplications Machine and tool engineering, utoclaves, Pump control, Refrigerant monitoring, Ship building applications Technical Data Wetted parts: Repeatability: Switching rate: s Stainless steel 17-7PH luminium, nickel-plated O-rings: FKM ±1 % at constant temperature max. 20/min Temperature range: -40 C C Protection class: Housing: Process connection: IP65 luminium, anodized 1/8" NPT female thread Electrical connection: Internal terminal strip ( mm 2 ) Standard: WGO terminal and cable gland M20 x 1.5; clamping range ø mm Electrical ratings and hysteresis: Weight: Set point adjustment: Intrinsically safe: pproval: --- large variety of micro switches offers different electrical ratings and hysteresis for many applications. DPD1T-...: approx. 1.6 kg DPD2T-...: approx. 1.7 kg Turn the adjustment screw clockwise to decrease the set point The switches are designed for intrinsically safe applications. Please add "Exi" to your ordering details when placing an order. To comply with the intrinsically safe approval following max. ratings must not be exceeded: Umax = 28 V Imax = 50 m * Static operating pressures up to 28 bar possible. Differential pressure of the adjustable range must not be exceeded. djustment range [bar] * Max. operating pressure [bar] Proof pressure [bar] Max. hysteresis of switch types in bar (end of range) Increasing press. Decreasing press. (short term) H, GH [bar] M, GM [bar] Specifications are subject to changes without notice. Index: E Overpressure SS , SS , SS , SS ,

25 Pressure Metal Diaphragm Diff. Press. Switches Type DPD1T-.../DPD2T-... Dimensions (in mm / inch) Specifications are subject to changes without notice. Index: E Process connection 1/8" NPT internal (high pressure) Plug M20 x pieces supplied with every switch Electrical ratings Micro switch H M 57/ / /5 Special features Micro switch with silver contacts Micro switch with silver contacts Supplied with 1/2" NPT plug 159/6.26 Volt C 50/60 Hz / /.54 Cable gland M20 x 1.5 (clamping range ø mm) supplied with every switch djustment screw(s) under the cover Volt DC 6 to Wiring for all types (contact status at atmospheric pressure) Process connection 1/8" NPT internal (low pressure) Power circuit À C=purple NC=blue NO=red NC NC C NO C NO Power circuit Á C=brown NC=orange NO=black À Á Comments Small hysteresis; High C-/ low DC-load Medium hysteresis; High C- and DC-loads GH Micro switch with gold-plated Small hysteresis GM contacts for low voltage and/or low current Medium hysteresis Options Ordering Example for order number Type DPD1T-... ST1 Plug, -pin + E, DIN EN (prev. DIN 4650) ST Plug, 6-pin + E, DIN EN 4651 ST2 mphenol plug 4-pin + E EXI for intrinsically safe application EXI for intrinsically safe application Micro switch Options 480 V C and 15 only upon request DPD2T-... pproval DPD1T or DPD2T H SS ST2 EXI Your order number Type Micro switch Options or 25

26 Bourdon Tube Pressure Switches Type B1S-.../B2S-... Mechanical single/dual pressure switch Repeatability ±1.0 % at constant temperature Features Bourdon tube pressure switch ll welded parts wetted. Direct acting, no friction, high accuracy djustment ranges bar pplications Pump control, Die-casting machines, Press control, Power plants, larm functions Technical Data Wetted parts: Process connection: Bourdon tube: Repeatability: Switching rate: s Stainless steel Stainless steel ±1 % at constant temperature max. 20/min Temperature range: -40 C C Protection class: Housing: Process connection: IP00 Without housing for installation in control panels: 1/4" NPT female thread except ranges marked with *). These switches have proof pressures above 500 bar and are provided with high pressure thread with adapter "G1/4 female". Electrical connection: Lead wire PVC 1.5 mm 2, length appr. 450 mm djustment range [bar] Electrical ratings and hysteresis: Weight: Set point adjustment: Intrinsically safe: pproval: --- Max. operating pressure [bar] Test pressure [bar] large variety of micro switches offers different electrical ratings and hysteresis for many applications. B1S-...: approx. 0.6 kg B2S-...: approx. 0.7 kg Turn the adjustment screw clockwise to decrease the set point The switches are designed for intrinsically safe applications. Please add "Exi" to your ordering details when placing an order. To comply with the intrinsically safe approval following max. ratings must not be exceeded: Umax = 28 V Imax = 50 m Max. hysteresis of switch types in bar (end of range) Increasing press. Decreasing press. (short term) H, GH [bar] M, GM [bar] 12SS SS SS SS* SS* SS*

27 Pressure Bourdon Tube Pressure Switches Type B1S-.../B2S-... Dimensions (in mm / inch) B1S... leads approx. 450/17.72 long 40/1.57 0/ 1.18 max. 127/5 Process connection 1/4" NPT female djustment screw B2S... 6 leads approx. 450/17.72 long 40/ /0.47 max. 127/5 Process connection 1/4" NPT female Circuit 1 slotted nut hex SW Circuit 2 2 adjustment screws slotted nut hex SW Electrical ratings Micro switch H M Special features Micro switch with silver contacts Micro switch with silver contacts Volt C 50/60 Hz * * 0/ /1.575 dapter see "s" *) 16/ 0.6 5/0.197 G1/4 ø / /0.5 SW 19 Mounting plate max. 15/0,59 thick, Mounting bores min. ø 26/1.02 Volt DC 6 to Wiring for all types (contact status at atmospheric pressure) Power circuit À C=purple NC=blue NO=red NC NC C NO C NO Power circuit Á C=brown NC=orange NO=black À Á Comments Small hysteresis; High C / low DC loads Medium hysteresis; High C and DC loads GH Micro switch with gold-plated Small hysteresis GM contacts for low voltage and/or low current Medium hysteresis * on request Ordering Example for order number Type Micro switch B1S or B2S H 48SS Your order number Type or Micro switch 27

28 Bourdon Tube Pressure Switches Type B1T-.../B2T-... Mechanical single/dual pressure switch Repeatability ±1.0 % at constant temperature Features Bourdon tube pressure switch ll welded parts wetted. Direct acting, no friction, high accuracy djustment ranges bar pplications Pump control, Die-casting machines, Press control, Power plants, larm functions Technical Data Wetted parts: Process connection: Bourdon tube: Repeatability: Switching rate: s Stainless steel Stainless steel ±1 % at constant temperature max. 20/min Temperature range: -40 C C Protection class: Housing: Process connection: Electrical connection: IP65 luminium, anodized 1/4" NPT female thread except ranges marked with *). These switches have proof pressures above 500 bar and are provided with high pressure thread with adapter "G1/4 female". Internal terminal strip ( mm 2 ) Standard: WGO terminal and cable gland PG1,5 djustment range [bar] Electrical ratings and hysteresis: large variety of micro switches offers different electrical ratings and hysteresis for many applications. Weight: B1T-...: approx. 1.1 kg B2T-...: approx. 1.2 kg Set point adjustment: Intrinsically safe: pproval: --- Max. operating pressure [bar] Proof pressure [bar] Turn the adjustment screw clockwise to decrease the set point The switches are designed for intrinsically safe applications. Please add "Exi" to your ordering details when placing an order. To comply with the intrinsically safe approval following max. ratings must not be exceeded: Umax = 28 V Imax = 50 m Max. hysteresis of switch types in bar (end of range) Increasing press. Decreasing press. (short term) H, GH [bar] M, GM [bar] 12SS SS SS SS* SS* SS

29 Pressure Bourdon Tube Pressure Switches Type B1T-.../B2T-... Dimensions (in mm / inch) B1T... 4/ 1.4 4/ /2.795 Terminal strip (2 x pins on B2T) 27/ / 0.26 Process connection Electrical ratings Micro switch H M 9/ / /2.2 Set screw SW under the lid Special features Micro switch with silver contacts Micro switch with silver contacts 6/ / / 0.98 Cable gland PG 1,5 (cable diameter ø mm) Volt C 50/60 Hz * * djustment screw (only S version) 1/ /0.6 8/ / /7.48 /0.9 /0.9 djustment screw Power circuit À B2T... Volt DC 6 to Wiring for all types (contact status at atmospheric pressure) djustment screw Circuit Á Power circuit À C=purple NC=blue NO=red UNF NC NC 5/ ø /0.12 C NO C NO Power circuit Á C=brown NC=orange NO=black À Á dapter see "s" *) /1,575 16/ 0.6 SW 19 Comments Small hysteresis; High C / low DC loads Medium hysteresis; High C and DC loads GH Micro switch with gold-plated Small hysteresis GM contacts for low voltage and/ or low current Medium hysteresis * on request Options Ordering Example for order number Type B1T-... ST1 Plug, -pin + E, DIN EN (prev. DIN 4650) ST Plug, 6-pin + E, DIN EN 4651 ST2 mphenol plug 4-pin + E EXI for intrinsically safe application EXI for intrinsically safe application Micro switch Options B1T or B2T H 48SS ST2 B2T-... G1/4 Your order number Type Micro switch or Options 29

30 Bourdon Tube Press. Switches Type B1X-.../B2X-... Mechanical single/dual pressure switch Repeatability ±1.0 % at constant temperature Features Bourdon tube pressure switch ll welded parts wetted. Direct acting, no friction, high accuracy djustment ranges bar pplications Petrochemicals industry, Process technology, Shipbuilding technology, larm applications Technical Data Wetted parts: Process connection: Bourdon tube: Repeatability: Switching rate: Stainless steel Stainless steel ±1 % at constant temperature max. 20/min Temperature range: -40 C C Protection class: Housing: Process connection: IP65 Explosion proof housing, aluminum anodized and lacquered 1/4" NPT female thread except ranges marked with*). These switches have proof pressures above 500 bar and are provided with high pressure thread with adapter G1/4 IG. Electrical connection: Internal terminal strip ( mm 2 ), approved cable gland has to be provided by the customer s djustment range [bar] Electrical rating and hysteresis: Weight: Set point adjustment: Intrinsically safe: Many micro switch versions with different switching powers and hysteresis are applicable and make it possible to make customized changes. B1X-...: approx..9 kg B2X-...: approx..9 kg Turn the adjustment screw clockwise to decrease the set point. The switches are designed for intrinsically safe applications. Please add "Exi" to your ordering details when placing an order. To comply with the intrinsically safe approval following max. ratings must not be exceeded: Umax = 28 V Imax = 50 m pproval: Ex: Ex d II C T6 acc. to TEX culus: Class I, Groups B, C, D Class II, Groups E, F, G Max. operating pressure [bar] Proof pressure [bar] acc. to Underwriter Laboratories Inc. and Canadian Standard ssn. Max. hyst. of the different switches in bar (end of range) Increasing press. Decreasing press. (short term) H, GH [bar] M, GM [bar] 12SS Specifications are subject to changes without notice. Index: E 20SS SS SS*

31 Pressure Bourdon Tube Press. Switches Type B1X-.../B2X-... Dimensions (in mm / inch) Specifications are subject to changes without notice. Index: E 11/0.4 B1X... 11/ /1.47 1/4. Electrical ratings Micro switch H M Conduit connection 1/2" NPT 21.5/0.85 ø 165/6.496 djustment screw 11/0.4 Special features Micro switch with silver contacts Micro switch with silver contacts 11/ 0.4 B2X /1.47 1/4. Volt C 50/60 Hz * * Conduit connection /4" NPT 21.5/0.85 ø 165/6.496 djustment screws: Power circuit Á Power circuit À Switching- and connection diagram for all types (pressureless) NC NC C NO C NO 65/2.56 Mounting bore À Á ø 8/ /0.4 SW 19 65/ / 0. Process connection 1/4" NPT Volt DC 6 to /5 Power circuit À C=lila 217/8.54 NC=blue NO=red Power circuit Á C=brown NC=orange NO=black Comments Small hysteresis; High C / low DC loads Medium hysteresis; High C and DC loads GH Micro switch with gold-plated Small hysteresis GM contacts for low voltage and/or low current Medium hysteresis * on request pprovals EX UL EXI Options Ex d approval culus approval Ex i approval P2 = 1/2" NPT F SS Process connection Ordering Example for order number Type Your order number Type Micro switch Micro switch Options pproval B1X or B2X H 72SS P2 UL Options or pproval 1

32 Diaphragm Seal Piston Press. Switches Type E1S-... Mechanical single switch Repeatability ±2.0 % at constant temperature Features Diaphragm seal piston pressure switch, scale for setpoint reference djustment ranges bar, vacuum bar, pressure pplications Machine and tool engineering, Dosing machines, Plant engineering, Lubricant monitoring Technical Data Wetted parts: Diaphragm: Process connection: Repeatability: Switching rate: NBR Optional: FKM, PTFE, EPDM, CR anodized aluminium Optional: brass, polysulfone, aluminium nickel-plated ±1 % at constant temperature max. 20/min Temperature range: -0 C C Protection class: Housing: Process connection: Pressure switches: Vacuum switches (VC): s IP00 Without housing for installation in control panels 1/4" NPT female Optional: 1/8" NPT female + 1/2" NPT male (P6) G1/4 female (P7) 1/4" NPT female (P4) 1/8" NPT female +1/2" NPT male (P6) djustment range [bar] Electrical connection: Electrical rating and hysteresis: Weight: Set point adjustment: Pressure switches: Vacuum switches: Intrinsically safe: pproval: --- Max. operating pressure [bar] Proof pressure [bar] * Screw terminals Many micro switch versions with different switching powers and hysteresis are applicable and make it possible to make customized changes. E1S-...: approx. 0.5 kg Turn the adjustment screw clockwise to increase the set point. Switching point lowers by turning the adjustment screw clockwise. The switches are designed for intrinsically safe applications. Please add "Exi" to your ordering details when placing an order. To comply with the intrinsically safe approval following max. ratings must not be exceeded: Umax = 28 V Imax = 50 m * Designed for 70 bar proof pressure, for practical production reasons, however, the standard proofing pressure is 0 bar. Pressure switches Max. hysteresis of switch types in bar (end of range) Increasing press. Decreasing press. (short term) H, GH [bar] M, GM [bar] / / / / Vacuum switches VC

33 Pressure Diaphragm Seal Piston Press. Switches Type E1S-... Dimensions (in mm / inch) Process connection Common C Electrical ratings Micro switch H M djustment screw 17.5/ 0.69 Wiring (contact status at atmospheric pressure) Special features Micro switch with silver contacts Micro switch with silver contacts NC C NO Normally Open NO Normally Closed NC 6,5/1,44 Volt C 50/60 Hz approx. 0.5/.97 49/ / 0.96 C=brown NC=orange NO=black 18/0,71 18/ 0.71 Volt DC 6 to /2,4 49/1,9 24.5/ / / / mounting screws in diagonal order 18/0,71 Mounting cutout Plate thickness 1.6 mm max. 18/0, /0,71 5.5/ /0,71 Comments Small hysteresis; High C / low DC loads Medium hysteresis; High C and DC loads GH Micro switch with gold-plated Small hysteresis GM contacts for low voltage and/or low current Medium hysteresis Process connection / diaphragm / option Ordering Example for order number Process connection Diaphragm Pressure switches Vacuum switches VC not VC (P4) 1/4" NPT female (P4) 1/4" NPT female ( ) NBR ( ) NBR (P6) 1/8" NPT female + 1/2" NPT male (P6) 1/8" NPT female + 1/2" NPT male (V) FKM (V) FKM (P6-PLS) material PLS, up to 17 bar only (P7) G1/4 female (N) CR Type Micro switch Process connection Diaphragm E1S H P6 V (T) PTFE (E) EPDM 5.5/ /0, / 1.75 Your order number Type Micro switch Process connection Diaphragm

34 Diaphragm Seal Piston Press. Switches Type E1H-... Mechanical single switch Repeatability ±2.0 % at constant temperature Features Diaphragm seal piston pressure switch, scale for setpoint reference djustment ranges bar and bar pplications Machine and tool engineering, Dosing machines, Plant engineering, Sprinkler control Technical Data Wetted parts: Diaphragm: Process connection: Repeatability: Switching rate: NBR Optional: FKM, PTFE, EPDM, CR anodized aluminium Optional: brass, polysulfone, aluminium nickel-plated ±1 % at constant temperature max. 20/min Temperature range: -0 C C Protection class: Housing: Process connection: Pressure switches: Vacuum switches (VC): s Pressure switches IP00 Without housing for installation in control panels 1/4" NPT female (P4) Optional: 1/8" NPT female + 1/2" NPT male (P6) G1/4 female (P7) 1/4" NPT female (P4) 1/8" NPT female +1/2" NPT male (P6) djustment range [bar] Electrical connection: Electrical ratings and hysteresis: Weight: Set point adjustment: Pressure switches: Vacuum switches: Intrinsically safe: pproval: --- Max. operating pressure [bar] Proof pressure [bar] * Screw terminals and cable gland M20x1.5 mm large variety of micro switches offers different electrical ratings and hysteresis for many applications. E1H-...: approx. 0.7 kg Turn the adjustment screw clockwise to increase the set point. Turn the adjustment screw clockwise to decrease the set point. The switches are designed for intrinsically safe applications. Please add "Exi" to your ordering details when placing an order. To comply with the intrinsically safe approval following max. ratings must not be exceeded: Umax = 28 V Imax = 50 m * Designed for 70 bar proof pressure, for practical production reasons, however, the standard proofing pressure is 0 bar. Max. hysteresis of switch types in bar (end of range) Increasing press. Decreasing press. (short term) H, GH [bar] M, GM [bar] / / / / Vacuum switches VC ,

35 Pressure Diaphragm Seal Piston Press. Switches Type E1H-... Dimensions (in mm / inch) 66.5 ±0.5/ 2.62 ±0.02 4/1.4 max. 85/.46 Electrical ratings Micro switch H M Special features Micro switch with silver contacts Micro switch with silver contacts Cable gland M20 x 1.5 (cable diameter ø7/ /0.47 mm) M4 (2x) 62 ±0.5/ 2.44 ±0.02 Volt C 50/60 Hz ±0,5/ 2.56 ± / /1.9 82/.2 approx. 146/5.75 Volt DC 6 to Switching (contact status at atmpsheric pressure) NC C NO C=brown NC=orange NO=black Comments Small hysteresis; High C / low DC loads Medium hysteresis; High C and DC loads GH Micro switch with gold-plated Small hysteresis GM contacts for low voltage and/or low current Medium hysteresis Process connection / Diaphragm Ordering Example for order number Type Micro switch Process connection Options ST1 Plug, -pin + E, DIN EN (prev. DIN 4650) ST2 EXI RD mphenol plug 4-pin + E for intrinsically safe application Manual reset with G-Micro switch Process connection Diaphragm Option E1H H P6 V ST2 Diaphragm Pressure switches Vacuum switches VC not VC (P4) 1/4" NPT female (P4) 1/4" NPT female ( ) NBR ( ) NBR (P6) 1/8" NPT female + 1/2" NPT male (P6) 1/8" NPT female + 1/2" NPT male (V) FKM (V) FKM (P6-PLS) material PLS, up to 17 bar only (P7) G1/4 female (N) CR (T) PTFE (E) EPDM Your order number Type Micro switch Process connection Diaphragm Option 5

36 Diaphragm Seal Piston Press. Switches Type P1H-... Mechanical single switch Repeatability ±2.0 % at constant temperature Features Mechanical pressure switches, external setpoint adjustment djustment ranges bar pplications Hydraulic and pneumatic power units, Shipbuilding applications Technical Data Wetted parts: Diaphragm: Process connection: Repeatability: Switching rate: s NBR Optional: FKM, PTFE luminium, anodized Optional: stainless steel ±2 % at constant temperature max. 20/min Temperature range: -0 C C Protection class: Housing: Housing: Cap: Process connection: Electrical connection: IP65 luminium, anodized Steel, galvanized 1/4" NPT female thread Optional: 1/2" NPT female thread (P2) Screw terminals and cable gland 1/2" NPT, cable diameter ø mm djustment range [bar] Electrical ratings and hysteresis: Weight: Set point adjustment: Intrinsically safe: pproval: Max. operating pressure [bar] Proof pressure [bar] large variety of micro switches offers different electrical ratings and hysteresis for many applications. P1H-...: approx. 1.2 kg Turn the adjustment screw clockwise to increase the set point The switches are designed for intrinsically safe applications. Please add "Exi" to your ordering details when placing an order. To comply with the intrinsically safe approval following max. ratings must not be exceeded: Umax = 28 V Imax = 50 m NCE Max. hysteresis of switch types in bar (end of range) Increasing press. Decreasing press. (short term) B H, GH [bar] K [bar] Specifications are subject to changes without notice. Index: C

37 Pressure Diaphragm Seal Piston Press. Switches Type P1H-... Dimensions (in mm / inch) Specifications are subject to changes without notice. Index: C 12 / / 2.85 djustment screw Electrical ratings Micro switch H GH K, B 2 / /4,65 1.5/5.26 Special features Micro switch with silver contacts Micro switch with gold contacts for low voltage and low current Micro switch with silver contacts K: with sealed plunger and stainless steel blade 46/1.81 Process connection 1/4" NPT female 54/2.1 Material / Options / Diaphragm Ordering Volt C 50/60 Hz /0.15 ø7/0.28 0/1.18 / 1.0 Cable gland 1/2" NPT (cable diameter ø mm) screw terminals on micro switch 2.5 / 4.05 Volt DC 6 to 28 NC Set screw to lock adjustment screw C NO 60.5/2.8 Wiring for all types (contact status at atmospheric pressure) C=brown NC=orange NO=black Comments Small hysteresis; High C / low DC loads Small hysteresis , ,0,0 6,0 0,2 Medium hysteresis; High C and DC loads Material Options Diaphragm ( ) luminium (P2) 1/2" NPT female SS ( ) NBR (SS) Stainless steel (V) FKM Example for order number Type Micro switch Material Options Diaphragm P1H H 85 SS P2 V (T) PTFE Your order number Type Micro switch Material Options Diaphragm 7

38 Diaphragm Seal Piston Press. Switches Type P1X-... Mechanical single switch Repeatability ±2.0 % at constant temperature Features Mechanical pressure switches, Switching point can be adjusted with corresponding reference unit during operation djustment ranges bar pplications Hydraulic and pneumatic power units, utoclaves, Shipbuilding applications Technical Data Wetted parts: Diaphragm: Process connection: Repeatability: Switching rate: s NBR Optional: FKM, PTFE luminium, anodized Optional: stainless steel ±2 % at constant temperature max. 20/min Temperature range: -0 C C Protection class: Housing: Housing: Cap: Process connection: Electrical connection: IP65 Explosion proof housing acc. to CS and culus luminium, anodized luminium, anodized 1/4" NPT female thread Optional: 1/2" NPT female thread Screw terminals and cable gland 1/2" NPT female thread djustment range [bar] Electrical ratings and hysteresis: Weight: Set point adjustment: Intrinsically safe: pproval: Max. operating pressure [bar] Proof pressure [bar] large variety of micro switches offers different electrical ratings and hysteresis for many applications. P1X-...: approx. 1. kg Turn the adjustment screw clockwise to increase the set point The switches are also applicable for inherent safety applications. dd "Exi" in case of ordering. The following max. values are valid when using those switches: Umax = 28 V Imax = 50 m CS, UL File No. E704, NCE Max. hysteresis of switch types in bar (end of range) Increasing press. Decreasing press. (short term) B H, GH [bar] K [bar]

39 Pressure Diaphragm Seal Piston Press. Switches Type P1X-... Dimensions (in mm / inch) 14 / ø7/0.28 djustment screw 2 / /4.65 Electrical ratings Micro switch H GH K, B Special features Micro switch with silver contacts 46/ /2.1 Micro switch with gold-plated contacts for low voltage and low current Micro switch with silver contacts K: with sealed plunger and/ or stainless steel blade Material / Options / Diaphragm Ordering Example for order number Type Micro switch Process connection 1/4" NPT internal 72.5 / / 1.18 Volt C 50/60 Hz / 1.0 8/0.15 Conduit connection 1/2" NPT 2.5 / 4.05 ø2/ 1.26 Set screw to lock adjustment screw Volt DC 6 to 28 NC C NO 67.5/2.66 Wiring for all types (contact status at atmospheric pressure) C=brown NC=orange NO=black Comments Small hysteresis; High C / low DC loads Small hysteresis Medium hysteresis; High C and DC loads Material Options Diaphragm ( ) luminium (P2) 1/2" NPT female SS ( -) NBR (SS) Stainless steel (V) FKM Material Options Diaphragm P1X H 85 SS P2 V (T) PTFE Your order number Type Micro switch Material Options Diaphragm 9

40 Diaphragm Seal Piston Press. Switches Type MSPS-... Mechanical single switch Repeatability ±2.0 % at constant temperature Features Metal diaphragm pressure switch, Set point can be adjusted with corresponding reference unit during operation djustment ranges bar pplications ir conditioning, Ventilation control, Steam ejectors Technical Data Wetted parts: Diaphragm: Process connection: Repeatability: Switching rate: s NBR Stainless steel ±1 % at constant temperature max. 20/min Temperature range: -5 C C Protection class: IP00 Housing: --- Process connection: 1/4" NPT male thread Electrical connection: Spade connector 6, DIN Electrical ratings and hysteresis: Many micro switch versions with different switching powers and hysteresis are applicable and make it possible to make customized changes. djustment range [bar] Weight: Set point adjustment: Intrinsically safe: pproval: --- Max. operating pressure [bar] Proof pressure [bar] MSPS-...: approx. 0.2 kg Turn the adjustment screw clockwise to increase the set point The switches are designed for intrinsically safe applications. Please add "Exi" to your ordering details when placing an order. To comply with the intrinsically safe approval following max. ratings must not be exceeded: Umax = 28 V Imax = 50 m Max. hysteresis of switch types in bar (end of range) Specifications are subject to changes without notice. Index: C Increasing press. Decreasing press. (short term) EE, FF [bar] DD, JJ [bar] 5SS SS SS

41 Pressure Diaphragm Seal Piston Press. Switches Type MSPS-... Dimensions (in mm / inch) Specifications are subject to changes without notice. Index: C 48 /1.89 Electrical ratings Micro switch EE, FF DD, JJ Ordering Special features Micro switch with silver contacts Micro switch with silver contacts Example for order number Type Micro switch djustment screw 40 /1.57 Volt C 50/60 Hz MSPS FF 15SS 60/2.6 Process connection 74/2.98 Volt DC Common C Normally Open NO Normally Closed NC (only micro switch types FF and JJ) Wiring for all types (contact status at atmospheric pressure) NC C NO C=brown NC=orange NO=black Comments Medium hysteresis; High C voltage Medium hysteresis; High C voltage Your order number Type Micro switch 41

42 Compact Pressure Switches Type 9671X / 9681X Diaphragm seal piston sensor in explosion proof housing, for harzardous areas, accuracy class 2% f. s. Features Stainless steel body and parts, Flameproof enclosure according to TEX, UL, CS, Safe to adjust during operation, 1 switching contact (SPDT) djustment ranges Type 9671X: bar bar, vacuum Type 9681X: bar, pressure pplications Process Industry, Petrochemical Plants, Machine Tool Industry, Compressors Technical Data Wetted parts: Process fitting: Seals: Diaphragm: Repeatability: ±2 % f. s. Switching rate: Stainless steel, material no FKM, PTFE support ring FKM max. 0/min Temperature range: -0 C C Protection class: IP65 Housing: Stainless steel , explosion proof Process connection: Electrical connection: Switch type: Rating: Option: Weight: 1/4" NPT female thread 1/2" NPT G male conduit connector 18 WG 18" (450 mm) lead wire, PVC jacket Switch contact SPDT 11, 125 / V C 5, 0 V DC 1, 125 V DC 1 switching contact, 1 x DPDT 75 g Set point adjustment: Turn the adjustment wheel clockwise to increase the set point Vibration resistance: g, sine...500, MIL-STD 202F Shock resistance: 50 g, 11 ms, MIL-S-901C pprovals: CENELEC Ex d II C T6, UL #E704, CS #LR2254 and Division I Class I, Group, B, C & D; Class II, Group E, F & G Certificate no.: Options: LCIE 02 TEX 6027X Dual circuit 2 SPDT switches with DPDT function Gold contact switch, 1, 125 V C Ex terminal box Tamper proof cover 42

43 Pressure Compact Pressure Switches Type 9671X / 9681X Dimensions (in mm / inch) 11/5.14 (1/2 NPT) 125/4.92 (1/4 NPT) 5/4.1 1/ /1.5 Wiring / Option s x 18" leads (450 mm) and 1x ground per circuit (for single circuit, 7x for dual circuit) djustment wheel Ground screw Mounting bores only on K Press. connection 19.1 / / /0.8 18/0.7 1/2 NPT connector Wiring s for all types (contact status at atmospheric pressure) Power circuit À C=purple NC=blue NO=red NC NC C NO C NO at vacuum NC/NO vice versa Power circuit Á C=brown NC=orange NO=yellow Pressure 9681X Vacuum 9671X Option Function Circuit 1 Circuit 2 Circuit 1 Circuit 2 Normally Open / NO red yellow blue orange K with mounting holes Common / C purple brown purple brown Normally Closed / NC blue orange red yellow Earth green green Ordering 1 Switch contact SPDT (standard) Ordering 1 Switch contact DPDT (option) djustment ranges [bar] Increasing press. Decreasing press. Max. hysteresis (end of range) À Á Max. operating pressure Proof pressure min. max. min. max. [bar] [bar] [bar] 9681X-1CC X-2CC X-1CC X-2CC X-1CC- 9681X-2CC X-1CC X-2CC Vacuum switches 9671X-1CC 9671X-2CC ccessories Order Number Description Ex d - Terminal box incl. terminal (drawing on request) Tamper proof cover 4

44 Compact Pressure Switches Type 9692X Piston pressure switch with explosion proof housing, for hazardous areas, accuracy class 2% f. s. Features Stainless steel body and parts, Flameproof enclosure according to TEX, UL, CS, Safe to adjust during operation, 1 switching contact (SPDT) djustment ranges bar pplications Process Industry, Petrochemical Plants, Machine Tool Industry, Compressors Technical Data Wetted parts: Process connection: Seals: Piston: Repeatability: ±2 % f. s. Switching rate: Stainless steel, material no FKM Material no max. 0/min Temperature range: -0 C C Protection class: IP65 Housing: Stainless steel , explosion proof Process connection: Electrical connection: Switch type: Rating: Option: Weight: 1/4" NPT female thread 1/2" NPT G male conduit connector 18 WG 18" (450 mm) lead wire, PVC jacket Switch contact SPDT 11, 125 / V C 5, 0 V DC 1, 125 V DC 1 switching contact, 1 x DPDT 75 g Set point adjustment: Turn the adjustment wheel clockwise to increase the set point Vibration resistance: g, sine...500, MIL-STD 202F Shock resistance: 50 g, 11 ms, MIL-S-901C pproval: CENELEC Ex d II C T6, UL #E704, CS #LR2254 and Division I Class I, Group, B, C & D; Class II, Group E, F & G Certificate no.: Options: LCIE 02 TEX 6027X Dual circuit 2 SPDT switches with DPDT function Gold contact switch, 1, 125 V C Ex terminal box Tamper proof cover 44

45 Pressure Compact Pressure Switches Type 9692X Dimensions (in mm / inch) 1/5.25 (1/2 NPT) 122/4.8 (1/4 NPT) 5/4.1 1/ /1.5 Electrical connection s x 18" leads (450 mm) and 1x ground per circuit (for single circuit, 7x for dual circuit) djustment wheel Ground screw Mounting bores only on K Press. connection 19.1 / / /0.8 21/0.8 1/2 NPT connector Wiring for all types (contact status at atmospheric pressure) Power circuit À C = purple NC = blue NO = red NC NC C NO C NO at vacuum NC/NO vice versa Power circuit Á C = brown NC = orange NO = yellow Pressure Vacuum Option Function Circuit 1 Circuit 2 Circuit 1 Circuit 2 Normally Open / NO red yellow blue orange K with mounting bores Common / C purple brown purple brown Normally Closed / NC blue orange red yellow Earth green green Ordering 1 Switch contact SPDT (standard) Ordering 1 Switch contact DPDT (option) djustment ranges [bar] Increasing press. Decreasing press. Max. hysteresis (end of range) Max. operating pressure À Á Proof pressure min. max. min. max. [bar] [bar] [bar] 9692X-1CC X-2CC X-1CC X-2CC X-1CC- 9692X-2CC X-1CC X-2CC X-1CC X-2CC ccessories Order Number Description Ex d - Terminal box incl. terminal (drawing on request) Tamper proof cover 45

46 Compact Pressure Switches Type Series 8000 Series mechanical pressure switches in diaphragm or piston design. The successors of the product lines XTM, XTK, X1T and have the additional advantage of very low and precise switching point settings. Index: E Features Modular construction, Versatile, High-quality materials, 0% assays, Long pressure spring djustment ranges bar pplications OEM applications, Mobile- and industrial-hydraulics and pneumatics, Test bed and apparatus engineering, Heavy industry Technical Data Wetted parts: standard: optional: Repeatability: Switching rate: Temperature range: Piston switch: Diaphragm switch: Protection class: standard: optional: NBR, PTFE with bronze and stainless steel 1.401; pistons: steel FKM, EPDM, CR instead of NBR ±1% type, piston pressure switch ±2% type, diaphragm pressure switch max. 60/min piston pressure switch max. 0/min diaphragm pressure switch -40 C C (-40 F F) -20 C C (-4 F F) IP65 (plug connector), IP68 (cable) UL Inherent safety II 1G Ex ia IIB T6 (DIN plug) - EXI Ex ia IIC T6 (cable version) - EXI II 1GD Ex ia D 20 T0 UL, Type 4, for indoor and outdoor use s and proof pressures djustment range (pressure increasing) djustment range (pressure decreasing) Housing: standard: optional: luminium diecast 20 Stainless steel / SS 04, Version - V Process connection: CETOP flange 40x40 mm, see dimensions Electrical connection: Weight: Total: CETOP flange version: dapter version straight: dapter version 90 offset: dapter version X1T compatible: Micro switch: Set screw: pprovals: see dimensions 400 g (0.88 lbs) 50 g (0.77 lbs) 620 g (1.6 lbs) 675 g (1.48 lbs) 70 g (1.61 lbs) Change-over contact (SPDT) Stainless steel / SS04 (SW5) GL, Ex ia, culus, further approvals on request Max. operating pressure Proof pressure Max. hysteresis range end [bar] [psi] [bar] [psi] [bar] [psi] [bar] [psi] [bar] [psi] Diaphragm Diaphragm ( ) ( ) * (1,200) 2 b ( ) ( ) * (1,200) c ( ) ( ) * (1,200) Piston Piston 4 D (75...2,600) (4...2,20) (8,700) 5 E ( ,000) (40...4,00) (8,700) 6 F (1, ,700) ( ,550) (15,000) 15% 15% Specifications are subject to changes without notice. * Test pressure 200 bar (2,900 psi) upon request, results in less lifetime of the switch. 46

47 Pressure Compact Pressure Switches Type Series 8000 Dimensions (in mm / inch) Index: E ø 5.5/0.22 PL 1 Cable ø 6...8/ Switching- and connection diagram (pressureless) SW 5/0.2 (hexagon socket) ø 44/1.7 80/.12 40/1.57 Process connection CETOP flange 40 mm 5/ /. ø 0/ 1.18 PL1 PL2 C 1 1 NC 2 2 NO 4 PE --- Up to pressure stage 5 or E every pressure switch is supplied with two fastening screws M5 60 mm according to DIN 912 (.9, galvanized). The pressure switches of pressure stage 6 or F are supplied with four screws. 40 /1.57 Electrical connection (PL1 = standard) PL 1 Cube plug DIN EN (former DIN 4650) cable ø 6...8/ /0.4 M12 x 1 PL 2 Plug M12x1 mm, 4-pin approx. 22/ 0.87 Process connections Complete assembly with pressure switch only upon request 40/ /0.75 0/1.18 Drill hole for wall mounting ø 5.6/0.22 ø 5.6/ / /0.75 0/ / /1.57 ø 6.2/ 0.24 ø 6.2/ / 0.6 6/1.42 0/ /1.57 Connecting block 1, straight version Connecting block 2, version 90 offset (optional, only upon request) Connecting block, compatible with X1T, 960/96111 (optional, only upon request) Electrical ratings Micro switch Special features Volt C 50/60 Hz Volt DC Minimum capacitance Intrinsic safety Ex ia 1 Silver contacts V ~ 125 V ~ V= V= 2 Gold contacts* 125 V ~ V = m at 5 VDC * e.g. suitable for PLC and/or Ex ia m at 5 VDC Umax = 28 V Imax = 50 m Specifications are subject to changes without notice. Seal B N E V Ordering Example for order number Type Seal NBR CR EPDM FKM Your order number Process connection Options Housing V Micro switch Contact pprovals Electrical connection Seal Options pprovals PL1 B V GL EXI GL UL Ex ia Germanischer Lloyd culus approval 8 1 ccessories (To be listed separately in case of order. Blocks are slackly arranged.) Connecting block no. Order No. Process connection Designation Material /4" NPT female straight St passivated G 1/4" female straight St passivated /4" NPT female straight G 1/4" female straight G 1/4" female 90 offset /4" NPT female 90 offset G 1/4" female straight lmg4,5mn0,7 47

48 Compact Pressure Switch Type Series 9000 Mechanical pressure switch in piston design with 0 x 0 x 92 mm front face and precise switching point setting Features High-quality materials, 0% functional test, Compact design, Long pressure spring (precisely adjustable), G1/4" female thread Index: --- djustment ranges bar pplications OEM applications, Mobile and industrial hydraulics, Test bed and apparatus engineering, Heavy industry, Shipbuilding Technical Data Wetted parts: Repeatability: Switching rate: Temperature range: storage: piston switch: Protection class: Material: housing: electrical plug: adjustment screw: s [bar] sealing: PTFE/FKM fitting: lmg4,5mn piston: steel (0Cr6) ±2% (typically) max. 60/min. -40 C C (-40 F F) -20 C C (-4 F F) IP65 lmg4,5mn Polyamid (P) Stainless Steel (1.405) Decreasing press. [bar] djustment range Increasing press. [bar] Process connection: Electrical connection: Weight: Micro switch: pprovals: (in preparation) Max. hysteresis at full range max % G1/4" female thread DIN ISO EN plug (formerly DIN 4650) 175 g (0.9 lbs) (SPDT) silver contacts GL, Ex ia, others on request Max. operating pressure [bar] Proof pressure [bar] % Specifications are subject to changes without notice. 48

49 Pressure Compact Pressure Switch Type Series 9000 Dimensions (in mm/inch) Index: --- Cable ø 6...8/ SW 5/0.20 approx. 67/2.65 0/1.18 ø 29.5/1.16 ø G 1/4" 92/.62 Wiring and connection diagram PL1 C 1 NC 2 NO PE --- Electrical ratings Specifications are subject to changes without notice. Seal V Micro switch Ordering Example for order number Type Special features Seal FKM Volt C 50/60 Hz Process connection pprovals EXI GL Volt DC Micro switch Contact Electrical connection Seal pprovals PL1 V GL Ex ia Germanischer Lloyd Minimum capacitance 1 Silver contacts V~ V= m at 24 VDC Intrinsic safety Ex ia Umax = 28 V Imax = 50 m Your order number PL1 V 49

50 Compact Pressure Switches Type KLK-.../KLM-... Piston pressure switch Type KLK Repeatability ±1.0 % typical Diaphragm seal pressure switch Type KLM Repeatability ±2.0 % typical Features OEM pressure switch series, Compact design, Threaded connection Factory settings only fully tamper proof. djustment ranges bar pplications Mobile hydraulics, Motor control, Hydraulic clamping Technical Data Wetted parts: Type KLK: Type KLM: Repeatability: Type KLK: Type KLM: Switching rate: Type KLK: Type KLM: Temperature range: Type KLK: Type KLM: Protection class: Silicone cable (K2): Plug connector (S1): Housing: Type KLK: Type KLM: s NBR, PTFE Brass, roller bearing steel Stainless steel ±1 % typical ±2 % typical max. 60/min max. 0/min -40 C C -20 C C IP67 IP65 Brass and stainless steel Stainless steel * Higher operating pressure (up to 150 bar) (with proof pressure 200 bar) on request. Please add to your order! djustment range [bar] Proof pressure [bar] Process connection: M12 x 1.5 G1/4 male other connections on request Electrical connection: Electrical ratings capacity and hysteresis: Weight: Type KLK: Type KLM: Set point adjustment: Intrinsically safe: Max. operating pressure [bar] Silicone cable (K2) Plug connector (S1) large variety of micro switches offers different electrical ratings and hysteresis for many applications. 0.2 kg approx. 0.2 kg approx. Factory set large variety of micro switches offers different electrical ratings and hysteresis for many applications. pproval: EXI Ex i approval Max. hysteresis [bar] Increasing pressure short term end of range KLM /200* 40* 0.6 KLM /200* 40* 2.6 KLM /200* 40*.8 KLK KLK KLK

51 Pressure Compact Pressure Switches Type KLK-.../KLM-... Dimensions (in mm / inch) SW27 18/ / / / 0.48 M12 x 1.5 K2 - Silicone cable ø 27/1.06 Electrical ratings Micro switch PG7 ø 19/ /.7 Process connection Special features x 0.5 mm 2 2/ /0.09 SW27 S1 - Plug connector EN C 14./ 0.56 ø 16/0.6 20/ / 0.48 M12 x 1.5 Volt DC 1/1.22 ø 27/1,06 ø 19/ 0.75 Plug connector EN C 99/.898 SW15 Wiring (contact status at atmospheric pressure) K2 S1 Process connection NC not connected 2 1 C NO Comments 1 Micro switch with silver contacts More information on request. 2 Micro switch with gold-plated contacts $0.0 $0.04 $0.04 (U x I = max V) Process connection / Electrical connection Ordering C=green NC=white NO=brown Process connection Electrical connection Diaphragm (M1) M12 x 1,5 male (S1) Plug connector, -pin + E, EN C KLK: ( ) NBR (G1) G1/4 male (K2) Silicone cable x 0.5 mm 2 ; 600 mm long KLM: (V) FKM Options EXI HP (KLM only) Example for order number Type for intrinsically safe application operating pressure up to 150 bar Type KLM: KLM: (N) CR (E) EPDM Process connection Electr. connection Micro switch Diaphragm KLK or KLM 025 G1 S1 2 V EXI NO NC Option Your order number Type Type Process connection Electr. connection Micro switch Diaphragm KLK or KLM Option 51

52 Compact Piston Pressure Switches Type KD1-... Mechanical piston pressure switch Repeatability ±1.0 % typical Features OEM pressure switch, Factory setting only fully tamper proof. Larger deadband for pump controlling djustment ranges bar pplications Building and agricultural machines, Brake system control, Hydraulic accumulator control Technical Data Wetted parts: Repeatability: Switching rate: NBR, PTFE Brass, roller bearing steel ±1 % typical max. 60/min Temperature range: -40 C C Protection class: Silicone cable (K2): Spade connector (1): Housing: s IP67 IP65 Compact housing made of brass and stainless steel Process connection: Electrical connection: Electrical ratings and hysteresis: Weight: Set point adjustment: pproval: --- M12 x 1.5 male thread Other connections on request Silicone cable (K2) Spade connector DIN (1) Hysteresis factory set, see diagrams KD1-...: approx. 0.2 kg Factory set Specifications are subject to changes without notice. Index: C djustment range [bar] Proof pressure [bar] Max. operating pressure [bar] Max. hysteresis [bar] Increasing pressure short term end of range KD1-0 / KD1-60 /

53 Pressure Compact Piston Pressure Switches Type KD1-... Dimensions (in mm / inch) Specifications are subject to changes without notice. Index: C 18/0,71 14,/ / 0,6 SW27 /0,9 K2 - Silicone cable R 1,5/ 0.06 ø 26,7/1,05 ø 27/1,06 M12 x 1,5 PG7 Hysteresis diagrams Hysteresis [bar] Electrical ratings Special features 48 / 1,89 ø 20/ 0.79 x 0.5 mm 2 88 ±1 /,46 Process connection KD1-0 / 0 Volt DC 18/0,71 14,/ 0.56 max. min. 1 - Spade connector DIN Spade connector 6, DIN / 0,6 R 1,5/ 0.06 SW27 /0,9 djustable hysteresis difference bar Set point [bar] ø 26,7/1,05 ø 27/1,06 M12 x 1,5 44 / 1,7 ø 20/ ±1 /,2 Process connection Hysteresis [bar] Micro switch with silver contacts 0 More information on request. Wiring (contact status at atmospheric pressure) K2 1 NC C NO Normally Open NO NC C NO Normally Closed NC NC C NO KD1-60 / 00 Comments C=green NC=white NO=brown C=Housing NC=not connected NO=Spade connector C=Housing NC=Spade connector NC=not connected Set point [bar] max. min. djustable hysteresis difference 14 bar Electrical connection / Options and accessories Electrical connection Options and accessories (K2) Silicone cable x 0.5 mm 2 ; 600 mm long (K1) EPD cable, 600 mm long (1) Spade connector 6, DIN 46244; green (2) Spade connector 6, DIN 46244; blue 5

54 Mechanical Pressure Switches ccessories Electrical plug-in connections (with sockets) Order Number Description Harting plug HN 7D (up to 48 V) Plug DIN 4650 for single switch (ST1) mphenol plug for 4 pins + ground (ST2) Plug DIN 4651 for dual switch (ST) Terminal Boxes Order Number Description Terminal box incl. adapter 1/2" NPT (for switch with 1/2" NPT female electrical connection) Reducers Order Number Description Max. pressure Material /8" NPT to G 1/4 female 50 bar Steel /4" NPT to G 1/4 female 50 bar Steel /4" NPT to G 1/2 male bar Steel /4" NPT to G 1/4 female 50 bar Stainless steel High pressure thread UNEF 9/ to G 1/4 female 1400 bar Stainless steel daptor G 1/4 for X1T 600 bar Steel Manometer Fittings DIN Order Number Description Max. pressure Material /8" NPT to G 1/2 male 520 bar /8" NPT to G 1/2 male 1400 bar Steel /8" NPT to G 1/2 male 1400 bar Specifications are subject to changes without notice. Index: C 54

55 Pressure Mechanical Pressure Switches Certificates Certificates Specifications are subject to changes without notice. Index: C Order Number Description Works certificate DIN Works certificate DIN Originating reference 55

56 Experts Specialists for monitoring and control of: Pressure Temperature Level Flow lmost sixty years of experience in the area of mechanical and electronic control of liquid media and responding to customers needs have resulted in an extensive range of products to meet a wide range of applications. s priority is clear. It is our commitment to quality instrumentation and exceptional customer service that has remained the cornerstone of our success. Based on our innovative and market-focused technologies in the areas of pressure, level, flow and temperature measuring processes we provide solutions that fit. Global Presence Global Presence Inc. 211 Fruitland venue Los ngeles, C U.S.. Phone: (2) Fax: (2) GmbH Dorn-ssenheimer Strasse 27 D-6120 Reichelsheim Phone: (+49) (0) Fax: (+49) /11 info@barksdale.de Specifications are subject to changes without notice. rt. no Index: D