Under-Seat Storage Tray

Transcription

1 Part Number ES6923 for VW MKV Golf/GTI and MKV Jetta/GLI/JSW Under-Seat Storage Tray This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat Reader Proper service and repair procedures are vital to the safe, reliable operation of all engine vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety. Although this material has been prepared with the intent to provide reliable information, no warranty (express or implied) is made as to its accuracy or completeness. Neither is any liability assumed for loss or damage resulting from reliance on this material. SPECIFICALLY, NO WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER WARRANTY IS MADE OR TO BE IMPLIED WITH RESPECT TO THIS MATERIAL. In no event will ECS Tuning, Incorporated or its affiliates be liable for any damages, direct or indirect, consequential or compensatory, arising out of the use of this material.

2 Components tray and cassette support bracket (4x) T20 Torx screws (2x) pop rivets Note: this kit and installation guide is for the left seat, but the right seat kit (ES6935) installs using the same procedure outlined here! Tools ratchet torque wrench 10mm triple-square T20 torx flashlight rivet gun (optional) Installation overview (1) Unbolt seat and position it to install tray (2) Install under-seat tray (3) Reinstall seat 2

3 Step 1 Position driver s seat as pictured. Tilt the seatback forward. Slide the seat all the way forward and raise the seat bottom so that you can access the two bolts that hold the seat rails to the body of the car. Remove the two bolts with a 10mm triple square bit. This specialty tool can be purchased from ECS Tuning (ES ). 10mm triple-square 3

4 Step 1 continued Slide the seat all the way back to remove the front two bolts. 10mm triple-square When all of the bolts are removed, tilt the entire seat and frame backwards. 4

5 Step 1 continued Rotate the seat 90 and lay it backwards towards the center console so that you can work on the underside while sitting outside of the car. Step 2 pry up Remove the tray from the cassette by prying up on the retaining tab on the underside of the cassette. You will see where the tray catches on the tab. Use a screwdriver, and be careful not to break the tab off! 5

6 Step 2 continued Identify the mounting points on the bottom of the seat. Pink is for the T20 Torx and green is for the pop rivets that affix the support bracket. front of seat cushion 6

7 Step 2 continued Install the support bracket with pop rivets in the two holes circled in green. If you do not have a rivet gun, don t worry, you can still install the storage tray without the support bracket. 2x rivets Align the holes in the cassette, pointed out in the photo on the right, with the holes on the bottom of the seat frame. The green arrow is for the fastener that bolts to the riveted bracket. 7

8 Step 2 continued Attach all of the fasteners using a T20 Torx screwdriver. Top left: Bottom left: 8

9 Step 2 continued Bottom right (through access hole). Support bracket (green arrow) and right side seat trim (pink arrow). 9

10 Step 2 continued You can now slide the tray into the cassette. You ll have to push it past the retaining tab. Make sure all the under-seat electrical harnesses are connected and secured. Rotate the seat back into place. There are locating dowels on the bottom of the seat rails. They position the rails in the proper place so you can bolt down the seat. 10

11 Step 3 Tighten the four 10mm triple-square bolts to 30 ft-lbs of torque. Double-check that the electrical harnesses under the seat are connected! 30 ft-lbs (40 Nm) 11

12 This completes the installation of the. We hope this installation guide has been helpful and informative. Thanks for reading! 12