PART'S MANUAL MODEL 5600 & 5690 ROUND BALERS M&W

Transcription

1 ROUND BALERS Published 10/01 P/N 4895WP PART'S MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or M&W ( ) to obtain a Free copy before operating the equipment. MODEL 5600 & , SERIAL NUMBERS CURRENT 5690, SERIAL NUMBERS CURRENT Art s-way Manufacturing Co., Inc. Hwy 9 West - PO Box 288 Armstrong, IA U.S.A 1020 South Ave. (712)Sangamon M&W Gibson City, Illinois Alamo Group Inc.

2 TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.

3 Parts Section 1 PARTS SECTION

4 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number, and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Group Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: M&W 1020 South Sangamon Ave. Art s-way Manufacturing Co., Inc. Gibson City, Illinois Hwy 9 West - PO Box 288 Armstrong, IA U.S.A (712) Alamo Group Inc. Parts Section 2

5 PART NAME INDEX BALE COUNT SENSOR - MODEL BALE RAMP EXTENSION CLUTCH 540 RPM (P/N ) DECAL LOCATION GUIDE... 4 DRIVELINE 1000 RPM DRIVELINE 540 RPM (P/N ) DUAL TWINE DRIVE ASSEMBLY DUAL TWINE TIE SYSTEM ELECTRICAL SCHEMATIC - MODEL ELECTRICAL SCHEMATIC - MODEL ELECTRICAL SYSTEM - MODEL ELEVATOR FRONT CHAMBER... 6 GEARBOX... 40, 42 HYDRAULIC SYSTEM... 20, 24 OPTIONAL - WINDROW GATHERING WHEEL OPTIONAL 1000 RPM CONVERSION KIT ( ) PICK-UP RAMP CABLE LIFT (RIGHT & LEFT) RAMP CHANNEL REAR CHAMBER STANDARD SAFETY LIGHTS UNDERSIDE WIRE HARNESS ROUTING WIRING DIAGRAM - MODEL WRAP INSERT WRAP ROLL MOUNTING SYSTEM - MODEL Alamo Group Inc. Parts Section 3

6 DECAL LOCATION GUIDE 2004 Alamo Group Inc. Parts Section 4

7 DECAL LOCATION GUIDE ITEM PART NO. QTY. DESCRIPTION SAFETY OPERATION DECAL DANGER - TAILGATE DECAL IID SHIELD DECAL (INNER DECAL) IID SHIELD DECAL (OUTER DECAL) DANGER - SHARP KNIFE DOOR SAFETY LOCK VALVE DECAL DECAL, WARNING BALER UPSET WARNING HAND PINCH DECAL PINCH POINT DECAL OIL LEAK DECAL CAUTION OPERATING DECAL 12 D103 1 PTO SPEED DECAL, 540 RPM RED OBLONG REFLECTOR DECAL 14 5W118 1 SLOW MOVING VEHICLE DECAL DOG CLUTCH DECAL ELEVATOR CHAIN ADJUSTMENT DECAL DOUBLE TWINE INSTALLATION INSTRUCTION DECAL NET ROUTING DECAL PICK-UP CRANK DIRECTION DECAL PICK-UP HEIGHT POSITION DECAL FILL LINE DECAL GREASE DECAL, 10HRS PICK-UP PIN DECAL OIL DECAL TWINE WRAP DECAL DECAL, OIL CHAIN, 4 HOURS YR. WARRANTY GENUINE PARTS DECAL TRACTOR CAUTION DECAL NOTICE TO OWNER MODEL NO DECAL, RH MODEL NO DECAL, RH MODEL NO DECAL, LH MODEL NO DECAL, LH LARGE M & W DECAL M&W LOGO DECAL, RH M&W LOGO DECAL, LH FRONT STRIPE DECAL REAR STRIPE DECAL MADE IN USA DRIVELINE SPANISH TRANSLATION CANISTER MANUAL C 2 LOCKNUT FLATWASHER BOLTS WC 1 MANUAL FOR CANISTER INSTRUCT DECAL - MANUAL OPERATOR S INSIDE 2004 Alamo Group Inc. Parts Section 5

8 FRONT CHAMBER 2004 Alamo Group Inc. Parts Section 6

9 FRONT CHAMBER ITEM PART NO. QTY. DESCRIPTION TWINE BOX FLOOR DIVIDER PANEL LOWER CHAIN DOOR, RH LOWER EXTENSION CHAIN DOOR TWINE BOX LID TWINE BOX HINGE TWINE BOX COVER W/ INSERTS FRONT CHAIN GUARD FRONT HOUSING HOLE COVER TONGUE JACK STAND TOP WIND FLEXIBLE DRAW LATCH CHAIN DOOR, LH SHAFT TRANSPORT SUPPORT COTTER PIN COMPRESSION SPRING JACK PIN PLASTIC KNOB KNOB STUD N13C 6 PANHEAD SCREW C 6 EXTERNAL TOOTH LOCKWASHER HEX MACHINE NUT C 2 ELASTIC STOP NUT ROLLER BEARING H8C 2 BOLT COMPRESSION SPRING SPRING BAR SPRING WASHER HAIR PIN COTTER UPPER CROSS PIPE GAS SPRING ASSEMBLY W/ BALL STUDS CHAIN DOOR ROD RUBBER HOLD-DOWN STRAP C 18 HEX LOCKNUT BOLT SAFETY CHAIN C 32 BOLT 39 6D FLANGED WHIZLOCK NUT FLATWASHER RUBBER STOP 42 5E805 2 TYRAP 43 6D SHEET METAL SCREW F4C 12 FLATHEAD SCREW HINGE PLATE BOLT H5C 2 HEX TAP SCREW BOLT ADJUSTING BLOCK C 4 ELASTIC STOP NUT HEX NUT FLATWASHER TWINE DIVIDER ROD C 4 HEX LOCKNUT COTTER PIN C 2 BOLT HINGED PLATE BOLT C 2 LOCKWASHER N4C 18 PANHEAD SCREW H5C 2 BOLT HEX LOCKNUT 2004 Alamo Group Inc. Parts Section 7

10 FRONT CHAMBER 2004 Alamo Group Inc. Parts Section 8

11 FRONT CHAMBER ITEM PART NO. QTY. DESCRIPTION TWINE GUIDE BUSHING C 8 LOCKWASHER RETAINING RING HEX INSERT DIVIDER PANEL UPPER MODIFIED COTTER PIN C 4 CARRIAGE BOLT HEX NUT C 1 HEX LOCKNUT 73 6D SHEET METAL SCREW HEX NUT LOCKWASHER H5C 6 CARRIAGE BOLT BALE SIZER LH BALE SIZER RH 2004 Alamo Group Inc. Parts Section 9

12 REAR CHAMBER 2004 Alamo Group Inc. Parts Section 10

13 REAR CHAMBER ITEM PART NO. QTY. DESCRIPTION 1 6D SHEET METAL SCREW CHAIN GUARD, REAR UPPER CHAIN GUARD W/ INSERTS, REAR MIDDLE CHAIN GUARD W/ INSERTS, REAR LOWER HINGED PIN HINGED PLATE ROLL PIN 8 6D FLANGED WHIZ LOCKNUT F4C 12 FLATHEAD SCREW C 2 BOLT BEARING CASTING 12 15B800 4 FLATWASHER LOCKNUT REAR HOUSING FLATWASHER C 10 LOCKWASHER BOLT C 2 HEX TAP BOLT FLATWASHER SPRING ANCHOR PIN SPRING ADJUST LEVER C 2 HEX JAM NUT LATCH SPRING ASSEMBLY LATCH PIVOT BUSHING FLATWASHER BOLT C 2 LOCKWASHER BOLT FLATWASHER LATCH BAR CLEVIS PIN COTTER PIN HEX LOCKNUT VINYL TUBE MOUNTING STRAP C 2 CARRIAGE BOLT 39 6D FLANGED WHIZLOCK NUT BOLT C 2 HEX LOCKNUT 42 15B FLATWASHER H5C 2 BOLT UNLATCH ROD CLEVIS C 2 HEX LOCKNUT HYDRAULIC CYLINDER CLEVIS ROD HEX NUT ADJUSTABLE YOKE END UPPER CYLINDER PIN HEX UNI-TORQUE HEX TANK ASSEMBLY LH HEX TANK ASSEMBLY RH HEX INSERT SUPPORT CLAMP VINYL TUBE Y-CONNECTOR Ref. CAP BOLT 2004 Alamo Group Inc. Parts Section 11

14 UNDERSIDE 2004 Alamo Group Inc. Parts Section 12

15 UNDERSIDE ITEM PART NO. QTY. DESCRIPTION HOLD-DOWN SUPPORT TELESCOPING PIPE TINE BAR PICK-UP ASSEMBLY (SEE PICK-UP) PICK-UP MOUNT LH PICK-UP MOUNT RH PICK-UP DRIVE SHIELD TAPERLOCK SPROCKET TAPERLOCK BUSHING SPRING BAR ROLLER POSITIONING PLATE PICK-UP SUPPORT, RH PICK-UP SUPPORT, LH SPROCKET MACHINE BUSHING 16 6D BEARING CARTRIDGE Ref FRONT HOUSING FRAME ROLLER HUB ROLLER ROLLER SHAFT 21 6D CONNECTOR LINK ROLLER CHAIN ROLLER CHAIN CONNECTOR LINK RETAINING RING ROLLER SHIELD, LH ROLLER SHIELD, RH LOWER HOUSING BRACE SPINDLE MOUNT SPINDLE W/HOLE COTTER PIN W 2 SEAL BEARING CONE BEARING CUP HUB AND CUP ASSEMBLY BEARING CUP BEARING CONE DRIVE STUD C 2 FLATWASHER C 2 HEX SLOTTED NUT HUB CAP STUD NUT COVER MOUNT STUD CROSS BEAM COVER WIRE ROPE CLAMP ROLL PIN CABLE PULLEY ROLL PIN CABLE PLATE PICK-UP CABLE 54 29N132 4 CABLE THIMBLE FLATWASHER FLATWASHER IDLER SPACER GUARD CHAIN TENSIONER HEX NUT COMPRESSION SPRING IDLER SPROCKET C 1 LOCKWASHER H5C 1 BOLT BEARING BOLT 2004 Alamo Group Inc. Parts Section 13

16 UNDERSIDE 2004 Alamo Group Inc. Parts Section 14

17 UNDERSIDE ITEM PART NO. QTY. DESCRIPTION C 32 LOCKWASHER WHEEL ARM WHEEL C 4 FLATWASHER COTTER PIN SPROCKET SAFETY PIN CLEVIS PIN BOLT C 4 LOCKWASHER HEX NUT KEY C 4 BOLT BOLT BOLT FLATWASHER C 8 LOCKWASHER C 12 LOCKWASHER FLATWASHER HEX NUT C 2 LOCKWASHER WASHER FLATWASHER HEX NUT BOLT H5C 2 BOLT BOLT BOLT HEX LOCKNUT LEAF SPRING COMPRESSION SPRING C 1 BOLT 99 7A BOLT BOLT MOUNTED FLOTATION TIRE ASSEMBLY TIRE WHEEL 104 TR415 2 VALVE STEM H5C 2 BOLT BOLT C 2 FLATWASHER COVER, HAND HOLE A/R HEX INSERT (INCLUDED IN ITEM 47) 2004 Alamo Group Inc. Parts Section 15

18 ELEVATOR 2004 Alamo Group Inc. Parts Section 16

19 ELEVATOR ITEM PART NO. QTY. DESCRIPTION A6C 2 SQUAREHEAD CUP POINT SETSCREW HEX NUT DOG CLUTCH, FIXED BALL BEARING RETAINING RING DOG CLUTCH, SLIDING COMPRESSION SPRING WASHER ROLL PIN DRIVE SHAFT, FRONT CROSS KEY SPACER TUBE ROLL PIN C 13 HEX LOCKNUT ROLLER RACE SPECIAL SOCKETHEAD CAPSCREW LEVER WIRE ROPE THIMBLE WIRE ROPE CLAMP CLUTCH CABLE ROLL PIN CABLE PULLEY H5C 8 CARRIAGE BOLT SPROCKET(5600 ONLY) SPROCKET & SHEAVE WLDMT(5690 ONLY) RELUBE FLANGETTE RELUBE BEARING W/ LOCKING COLLAR RELUBE FLANGETTE SELF-TAPPING GREASE FITTING A29C 6 ALLENHEAD CUP POINT NYLON LOCK SETSCREW ROLLER CHAIN CONNECTOR LINK C 2 HEX LOCKNUT H5C 1 BOLT TORSION SPRING CHAIN IDLER ARM IDLER SPACER FLATWASHER FLATWASHER IDLER SPROCKET BOLT A29C 2 ALLENHEAD CUP POINT NYLON LOCK SETSCREW SPROCKET ELEVATOR DRIVE SPROCKET CHAIN LIMITER FLATWASHER C 2 LOCKWASHER BOLT BEARING KEY ELEVATOR DRIVESHAFT STRIPPER PLATE FRONT SHAFT COVER F4C 12 FLATHEAD SCREW CUPPED SPRING WASHER HEX NUT C 13 LOCKWASHER FLATWASHER SPROCKET KEY C 7 CARRIAGE BOLT PIPE SPACER 2004 Alamo Group Inc. Parts Section 17

20 ELEVATOR 2004 Alamo Group Inc. Parts Section 18

21 ELEVATOR ITEM PART NO. QTY. DESCRIPTION REAR SHAFT COVER ELEVATOR IDLER SHAFT CHAIN CROSS BAR ROLL PIN ELEVATOR CHAIN SLIDING BRACKET CHAIN TENSIONER BRACKET WAVE SPRING WASHER CHAIN GUIDE MACHINE BUSHING AR MACHINE BUSHING BEARING W/ LOCKING COLLAR ELEVATOR IDLER SPROCKET LOCKING COLLAR ELEVATOR CHAIN W/CONNECTOR LINK Ref CONNECTOR LINK Ref ONE BAR CHAIN SECTION WASHER RETAINING RING BALL BEARING C 4 LOCKWASHER BOLT C 2 HEX LOCKNUT HEX NUT 86 15B FLATWASHER COMPRESSION SPRING ELEVATOR CHAIN TENSIONER SCREW 89 6D HEX FLANGE WHIZ SCREW COMPRESSION SPRING SPRING CAP C3C 1 ALLENHEAD CUP POINT SETSCREW PULLEY MOUNT SELF-TAPPING GREASE FITTING 95 9D LUBE BULKHEAD NUT 96 9D LUBE BULKHEAD CONNECTOR PIPE NIPPLE PIPE NIPPLE PIPE ELBOW A7C 2 SQUARE HEAD CUP POINT SETSCREW C 2 HEX JAM NUT IDLER ARM PIVOT BUSHING SPACER, SPRING STOP IDLER ARM STOP ANGLE BOLT C 1 LOCKWASHER 108 6D HEX FLANGE WHIZ LOCKNUT BOLT FLATWASHER CARRIAGE BOLT BEARING, FLANGE (INCLUDES ITEM #26) C 1 HEX JAM NUT BOLT FLANGETTE FLANGETTE W/FITTING 2004 Alamo Group Inc. Parts Section 19

22 HYDRAULIC SYSTEM 2004 Alamo Group Inc. Parts Section 20

23 HYDRAULIC SYSTEM ITEM PART NO. QTY. DESCRIPTION HYDRAULIC LINE, UPPER RIGHT HYDRAULIC LINE, LOWER RIGHT HYDRAULIC LINE, UPPER LEFT HYDRAULIC LINE, LOWER LEFT HYDRAULIC HOSE W/ PIPE THREADED ENDS HYDRAULIC HOSE W/FEMALE SWIVEL ONE END HYDRAULIC HOSE HYDRAULIC HOSE HYDRAULIC HOSE HYDRAULIC CYLINDER DOOR LOCK VALVE PICK-UP HYDRAULIC CYLINDER W/PIPE PORTS PICK-UP HYDRAULIC CYL. W/ORING BOSS PORT TWIN CLAMP HALVES TWIN COVER PLATE C 7 BOLT UNLATCH ROD CLEVIS COTTER PIN CYLINDER PIN, LOWER CYLINDER PIN, UPPER 21 15B FLATWASHER H5C 2 BOLT HEX LOCKNUT UNION TEE C 2 BOLT ELBOW MALE 90 DEG. W/ O/RING TWIN WELD PLATE 28 6D FLANGE WHIZ LOCKNUT PIPE CAP GROMMET ADAPTER HYD ELBOW W/PIPE THREADS ADAPTER HYD ELBOW W/O-RING C 2 HEX LOCKNUT C 1 HEX NUT CABLE PLATE WIRE ROPE CLAMP TUBE SPACER PICK-UP LIFT CONNECTOR H5C 1 BOLT H5C 1 BOLT FLATWASHER HEX LOCKNUT PICK-UP LIFT CABLE ARM PICK-UP LIFT HOUSING C 2 CARRIAGE BOLT 45 6D FLANGE WHIZLOCK NUT COTTER PIN THRUST WASHER PICK-UP LIFT SCREW PICK-UP CRANK ASSEMBLY (INCLUDES ITEMS # 51,52 & 53) PIPE BUSHING PICK-UP LIFT CRANK PICK-UP LIFT CRANK HANDLE WASHER CUP PUSH NUT BARREL ASSEMBLY FULL LOCKNUT PISTON 57 1 PISTON SEAL 59 1 O-RING ROD ASSEMBLY 61 1 O-RING 62 1 BACK-UP 2004 Alamo Group Inc. Parts Section 21

24 HYDRAULIC SYSTEM 2004 Alamo Group Inc. Parts Section 22

25 HYDRAULIC SYSTEM ITEM PART NO. QTY. DESCRIPTION LOCK WIRE HEAD 65 1 O-RING 66 1 BACK-UP 67 1 ROD WIPER Ref SEAL KIT (INCLUDES ALL ITEMS MARKED*) Ref SEAL KIT FOR ITEM # PIPE 2004 Alamo Group Inc. Parts Section 23

26 HYDRAULIC SYSTEM 2004 Alamo Group Inc. Parts Section 24

27 HYDRAULIC SYSTEM ITEM PART NO. QTY. DESCRIPTION HYDRAULIC CYLINDER 1 1 SEAL 2 1 O-RING 3 1 SEAL 4 1 SEAL 5 1 WEAR RING CYLINDER HEAD TUBE WLDMT ROD WLDMT SEAL KIT (CONSIST OF THOSE MARKED WITH *) DECAL-WARNING OIL LEAK (NOT SHOWN) 2004 Alamo Group Inc. Parts Section 25

28 DUAL TWINE TIE SYSTEM 2004 Alamo Group Inc. Parts Section 26

29 DUAL TWINE TIE SYSTEM ITEM PART NO. QTY. DESCRIPTION BEARING HOUSING BALL BEARING SPROCKET IDLER SHAFT RETAINING RING SPROCKET DRIVE SHAFT GEAR SHAFT/PINION BUSHING RH TRAVEL PLATE ASSEMBLY (INCLUDES 1 OF ITEMS #9 & #10) PERMANENT STUD ROLL PIN LH TRAVEL PLATE ASSEMBLY (INCLUDES 1 OF ITEMS #9 & #10) CHAIN COVER STUD SUB-ASSEMBLY (INCLUDES 4 OF ITEM #55) RH TWINE TRAVEL LIMIT LH TWINE TRAVEL LIMIT KNIFE STRAP H5C 2 BOLT HEX NUT H5C 4 CARRIAGE BOLT 19 6D FLANGED WHIZLOCK NUT CHAIN BEAM TWINE HOOK-WHITE LATCH, TRAVEL KNIFE CARRIER CHAIN GUIDE SPACER, KNIFE CARRIER ROLLER CHAIN SLIDER EXTENSION SPRING CARRIAGE BOLT BOLT H5C 9 BOLT BOLT BOLT BOLT C 2 HEX LOCKNUT C 8 HEX LOCKNUT C 2 ELASTIC STOP NUT HEX NUT C 2 HEX JAM NUT LOCKWASHER LOCKWASHER C 4 INTERNAL TOOTH LOCKWASHER C 3 CARRIAGE BOLT C 8 FLATWASHER 48 6D CONNECTING LINK 49 6D OFFSET LINK R 1 PLASTIC GEAR DRIVE PULLEY FLATWASHER KEY RETAINING RING PERMANENT STUD KEY, GEAR SHOULDER BOLT TORSION SPRING, COUNTER COUNTER COUNTER MOUNTING BRACKET P5C 4 MACHINE SCREW C 4 HEX MACHINE NUT C 4 INTERNAL TOOTH LOCKWASHER COUNTER COVER KNIFE BLADE ASSEMBLY 2004 Alamo Group Inc. Parts Section 27

30 DUAL TWINE TIE SYSTEM 2004 Alamo Group Inc. Parts Section 28

31 DUAL TWINE TIE SYSTEM ITEM PART NO. QTY. DESCRIPTION R2C 4 PHILLIP HEAD SCREW TWINE DRIVE ASSEMBLY TWINE GUIDE BRACKET TWINE GUIDE BUSHING RETAINING RING BOLT 72 11D FLANGED WHIZLOCK NUT C 2 WING NUT COMPRESSION SPRING DUAL TWINE BRAKE CARRIAGE BOLT RETAINING RING CHAIN GUIDE 2004 Alamo Group Inc. Parts Section 29

32 DUAL TWINE DRIVE ASSEMBLY 2004 Alamo Group Inc. Parts Section 30

33 DUAL TWINE DRIVE ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 11D FLANGED WHIZ NUT SPUR GEAR, 12 TEETH ELECTRIC MOTOR MOTOR MOUNT C 2 HEX MACHINE NUT C 2 EXT TOOTH LOCKWASHER ROLL PIN BEARING CAGE BEARING RETAINING RING RETAINING RING LOWER IDLER ARM IDLER SHAFT C 2 BOLT UPPER IDLER ARM BEARING BALL BEARING SHAFT, FEED ROLLER FEED ROLLER, DUAL TWINE MODIFIED SPUR GEAR, 60 TEETH EXTERNAL RETAINING RING BOLT LOCKWASHER MOUNTING BRACKET EXTERNAL SPRING H5C 5 BOLT C 1 BOLT HEX NUT TWINE GUIDE BUSHING RETAINING RING TWINE GUIDE BRACKET FLATWASHER H5C 2 CARRIAGE BOLT 35 6D FLANGED WHIZ LOCKNUT BOLT 2004 Alamo Group Inc. Parts Section 31

34 WRAP INSERT 2004 Alamo Group Inc. Parts Section 32

35 WRAP INSERT ITEM PART NO. QTY. DESCRIPTION PULLEY A2C 1 SOCKET HEAD SETSCREW V-BELT FLATWASHER 5 2F031 2 BELT IDLER BOLT BOLT C 4 LOCKNUT IDLER PULLEY ARM IDLER BUSHING RS TORSION SPRING CLUTCH PANEL, LOWER DIVIDER NUT C 32 LOCKWASHER BOLT C 3 LOCKWASHER CLUTCH RETAINING WASHER 18 6D5103A 10 FLANGETTE 19 6D BEARING CLUTCH BRACKET H5C 20 CARRIAGE BOLT CAM SHAFT BOLT BRACKET, HALL EFFECT CLUTCH - MODIFIED SPACER CUTT-OFF CAM ASSEMBLY 27A CAM 27B 3919A9C 3 SOCKET HEAD SETSCREW 27C 5C JAM NUT 27D ROLL PIN BRACKET, CAM SWITCH FLATWASHER 31 6D FLANGE LOCKNUT 32 MWSN EXTENSION SPRING IDLER ARM BASE SWING ARM RETAINING RING IDLER ROLLER ASSEMBLY 36A BEARING 36B IDLER ROLLER NET CHUTE DRIVE ROLLER ASSEMBLY END PLATE, RH 40 7A BOLT COUNTER RING ASSEMBLY TRIP ARM ASSEMBLY 42A ROLLER BEARING 42B TRIP ARM H5C 2 BOLT C 1 LOCKNUT H5C 1 BOLT STOP, TORSION SPRING BUMPER COTTER PIN TORSION SPRING, RH CUTTER BAR ASSEMBLY 50A KNIFE 50B 3981H1C 13 BOLT 50C C 13 FLATWASHER 50D CUTTER BAR IDLER BUSHING LS 2004 Alamo Group Inc. Parts Section 33

36 WRAP INSERT 2004 Alamo Group Inc. Parts Section 34

37 WRAP INSERT ITEM PART NO. QTY. DESCRIPTION TORSION SPRING, LH V-BELT H5C 1 BOLT FLANGETTE BEARING CLUTCH H5C 1 BOLT 59 6D FLANGE LOCKNUT END PLATE ASSEMBLY, LH FLATWASHER HEX NUT SPACER IDLER PULLEY ARM, RS C 1 FLATWASHER BELT TENSIONER BRACKET 2004 Alamo Group Inc. Parts Section 35

38 WRAP ROLL MOUNTING SYSTEM - MODEL Alamo Group Inc. Parts Section 36

39 WRAP ROLL MOUNTING SYSTEM - MODEL 5690 ITEM PART NO. QTY. DESCRIPTION BOLT W 1 PLASTIC KNOB ROLL LATCH HANDLE TENSION ROD HANDLE PIVOT BRACKET 6 6D FLANGE LOCKNUT ROLL PIN ROLL END STOP ROLL LATCH R 1 HOIST EYE HEX NUT EXTENSION SPRING 13 11D HEX FLANGE NUT H5C 1 BOLT ROLL TUBE MOUNTING ROLL MOUNTING TUBE SPACER WASHER A/R ROLL/NETTING 2004 Alamo Group Inc. Parts Section 37

40 PICK-UP 2004 Alamo Group Inc. Parts Section 38

41 PICK-UP ITEM PART NO. QTY. DESCRIPTION WASHER PICK-UP FRAME END PLATE, RH END PLATE, LH PICK-UP MOUNT, RH PICK-UP MOUNT, LH WINDROW GUIDE SHIELD, RH WINDROW GUIDE SHIELD, LH PICK-UP BAND PICK-UP CAM BALL BEARING BEARING FLANGETTE PICK-UP TINE, DOUBLE SPRING BEARING PLATE 16 29N132 2 THIMBLE BOLT BOLT BOLT C 17 LOCKWASHER C 6 LOCKWASHER C 4 CARRIAGE BOLT FLATWASHER KEY GREASE FITTING 26 6D SHEET METAL SCREW 27 6D HEX FLANGE SCREW 28 6D FLANGE WHIZ LOCKNUT HEX NUT PICK-UP SHAFT TINE BAR CAM ARM TINE SUPPORT ANGLE PICK-UP TINE BALL BEARING BOLT C 5 HEX LOCKNUT C 5 LOCKWASHER H5C 55 HEX LOCKNUT H5C 55 CARRIAGE BOLT BOLT BOLT C 5 FLATWASHER BUSHING BUSHING TINE BAR H5C 2 BOLT LOCKNUT 2004 Alamo Group Inc. Parts Section 39

42 GEARBOX 2004 Alamo Group Inc. Parts Section 40

43 GEARBOX ITEM PART NO. QTY. DESCRIPTION CASING SHIM BEARING SHAFT SNAP RING PLUG BEARING SNAP RING OIL SEAL CROWN WHEEL SHIM C8 4 BOLT EXTENSION PINION SHAFT SNAP RING C8 4 BOLT DIPSTICK PLUG SHIM PLUG KEY BOLT FLATWASHER GUARD LOCKWASHER HEX NUT BOLT LOCKWASHER GEARBOX COMPLETE - LESS ITEM #20 - # Alamo Group Inc. Parts Section 41

44 GEARBOX 2004 Alamo Group Inc. Parts Section 42

45 GEARBOX ITEM PART NO. QTY. DESCRIPTION HEX CAPSCREW FLATWASHER GUARD LOCKWASHER HEX NUT SEAL 7 K RETAINING RING 8 K FLATWASHER K FLATWASHER K FLATWASHER K FLATWASHER BALL BEARING 10 K RETAINING RING 11 K GEAR COVER 12 K GEARBOX GASKET C8 6 HEX CAPSCREW LOCKWASHER HEX CAPSCREW LOCKWASHER 17 K BEARING 18 K FLATWASHER K FLATWASHER K FLATWASHER 19 K GEAR SHAFT 20 K GEAR HOUSING KEY 22 K DRIVE SHAFT 23 K GEAR 24 K SEAL 25 K RETAINING RING 26 K FLATWASHER K FLATWASHER K FLATWASHER K FLATWASHER 27 K BALL BEARING 28 K PLUG 29 K FLATWASHER GEARBOX COMPLETE, LESS ITEM #1-5, 15,16 & (2) # Alamo Group Inc. Parts Section 43

46 DRIVELINE 540 RPM (P/N ) ITEM PART NO. QTY. DESCRIPTION YOKE CROSS BEARING KIT ROLL PIN INBOARD YOKE INNER PROFILE OUTER PROFILE & SLEEVE W. A INBOARD YOKE FRICTION CLUTCH SHIELD CONE, 6 RIBBED OUTER SHIELD TUBE, OVAL INNER SHIELD TUBE, ROUND BEARING RING SAFETY CHAIN DECAL, IID SHIELD DECAL, IID SHIELD REMOVED SCREW SUPPORT BEARING GREASE FITTING SHIELD CONE, 6 RIBBED REPAIR KIT, SLIDE LOCK YOKE IID HALF ASSEMBLY W/SHIELD, TRACTOR END IID HALF ASSEMBLY W/SHIELD & CLUTCH, BALER END 2004 Alamo Group Inc. Parts Section 44

47 CLUTCH 540 RPM (P/N ) ITEM PART NO. QTY. DESCRIPTION CLUTCH HOUSING FRICTION DISK HUB DRIVE PLATE DRIVE PLATE THRUST PLATE BELLEVILLE SPRING HEX NUT BACK-UP SPRING BALL COMPRESSION SPRING LOCK COLLAR FLANGED RING SNAP RING BELLEVILLE SPRING Q. D. FLANGE KIT (INCLUDES ITEMS 9-14) 2004 Alamo Group Inc. Parts Section 45

48 DRIVELINE 1000 RPM 2004 Alamo Group Inc. Parts Section 46

49 DRIVELINE 1000 RPM ITEM PART NO. QTY. DESCRIPTION OPTIONAL CONSTANT VELOCITY IID SHAFT, 1000 RPM W/ CLUTCH SLIDE COLLAR YOKE SPLINE GREASE FITTING DOUBLE YOKE INBOARD YOKE CROSS AND BEARING KIT ROLL PIN CROSS AND BEARING KIT INNER SHAFT OUTER SHAFT & SLEEVE INBOARD YOKE FRICTION CLUTCH BEARING RING OUTER SHIELD INNER SHIELD CONSTANT VELOCITY CONE & BEARING ASSEMBLY SHIELD CONE, 3 RIBBED SHIELD CONE, 6 RIBBED SAFETY CHAIN DANGER DECAL, OUTER (INCLUDED IN ITEM 13) DANGER DECAL, INNER (INCLUDED IN ITEM 9) SCREW (INCLUDED IN ITEMS 15, 16 & 17) SUPPORT BEARING GREASE FITTING Ref SLIDE LOCK YOKE REPAIR KIT (PART OF ITEM 1) Ref QUICK DISCONNECT FLANGE KIT (INCLUDES ITEMS 24,31,33,34,35,36 - PART OF ITEMS 11) SNAP RING CLUTCH HOUSING FRICTION DISK LINING HUB THRUST PLATE BELLEVILLE SPRING, WHITE BELLEVILLE SPRING, RED BALL NUT BACK-UP RING COMPRESSION RING LOCK COLLAR FLANGED RING 2004 Alamo Group Inc. Parts Section 47

50 WIRING DIAGRAM - MODEL Alamo Group Inc. Parts Section 48

51 WIRING DIAGRAM - MODEL 5690 ITEM PART NO. QTY. DESCRIPTION CLUTCH, MODIFIED HARNESS, HALL EFFECT SWITCH SWITCH - HARNESS HARNESS MOTOR SENSOR HARNESS CLUTCH C 8 HEX NUT C 12 LOCKWASHER N10C 4 PANHEAD SCREW HARNESS, CONTROL CORD CONTROL BOX BRACKET, CONTROLLER ANTI PIVOT WASHER KNOB NYLON JAM NUT SWITCH BRACKET H5C 4 HEX MACHINE SCREW C 4 LOCKWASHER C 4 FLATWASHER F10C 4 MACHINE SCREW C 3 BOLT CLAMP, SUPPORT C 3 HEX LOCKNUT 2004 Alamo Group Inc. Parts Section 49

52 BALE COUNT SENSOR - MODEL Alamo Group Inc. Parts Section 50

53 BALE COUNT SENSOR - MODEL 5690 ITEM PART NO. QTY. DESCRIPTION BRACKET, DOOR HINGE MAGNET H5C 2 BOLT ACTUATOR N7C 2 FLATWASHER C 2 FLATWASHER C 2 LOCKWASHER C 2 HEX MACHINE NUT SENSOR, MAGNETIC N7C 2 MACHINE SCREW C 2 FLATWASHER C 2 LOCKWASHER C 2 HEX MACHINE NUT BRACKET, DOOR OPEN SENSOR N9C 2 MACHINE SCREW C 2 FLATWASHER C 2 LOCKWASHER HEX MACHINE NUT SHIELD, DOOR OPEN SENSOR BOLT FLATWASHER 21 11D FLANGED LOCKNUT 22 6D FLANGED LOCKNUT 2004 Alamo Group Inc. Parts Section 51

54 ELECTRICAL SYSTEM - MODEL Alamo Group Inc. Parts Section 52

55 ELECTRICAL SYSTEM - MODEL 5600 ITEM PART NO. QTY. DESCRIPTION C 4 HEX NUT C 8 LOCKWASHER C 4 FLATWASHER C 4 EXTERNAL TOOTH LOCKWASHER H5C 4 HEX MACHINE SCREW F10C 4 SLOTTED FLATHEAD MACHINE SCREW SWITCH BRACKET H5C 3 BOLT CLAMP C 3 HEX LOCKNUT SWITCH HARNESS WIRE HARNESS, BALER END 13 5E805 9 TYRAP TYRAP BEADED TIE CONTROL HOUSING ASSEMBLY BRACKET-CONTROLLER KNOB ANTI-PIVOT WASHER 2004 Alamo Group Inc. Parts Section 53

56 ELECTRICAL SCHEMATIC - MODEL 5690 ITEM PART NO. QTY. DESCRIPTION - - ELECTRICAL SCHEMATIC - MODEL Alamo Group Inc. Parts Section 54

57 ELECTRICAL SCHEMATIC - MODEL 5600 ITEM PART NO. QTY. DESCRIPTION - - ELECTRICAL SCHEMATIC - MODEL Alamo Group Inc. Parts Section 55

58 STANDARD SAFETY LIGHTS 2004 Alamo Group Inc. Parts Section 56

59 STANDARD SAFETY LIGHTS ITEM PART NO. QTY. DESCRIPTION DUAL LAMP (RH) DUAL LAMP (LH) BOLT C 8 LOCKNUT MAIN HARNESS WISHBONE HARNESS SUPPORT CLAMP 8 5E805 8 TYRAP MALE PLUG SPRING AMBER LENS RED LENS LIGHT BULB BLACK BLANK FRONT HOUSING REAR HOUSING 2004 Alamo Group Inc. Parts Section 57

60 RAMP CABLE LIFT (RIGHT & LEFT) ITEM PART NO. QTY. DESCRIPTION PIN, CABLE ARM PIVOT CABLE CABLE ARM CLAMP CABLE ARM SUPPORT SPRING 7 6D SCREW H5C 2 BOLT LOCKNUT FLATWASHER 11 29N132 2 THIMBLE, CABLE WASHER C 2 LOCKWASHER NUT SPRING, (NOT SHOWN) BOLT SPACER, THIMBLE 2004 Alamo Group Inc. Parts Section 58

61 BALE RAMP EXTENSION ITEM PART NO. QTY. DESCRIPTION RAMP EXTENSION UPPER EXTENSION PIPE PIVOT PLATE LOWER EXTENSION PIPE PIVOT PLATE R. TORQ ROD ROLLER PLATE L. TORQ ROD ROLLER PLATE BOLT BOLT NUT LOCKWASHER GREASE FITTING 11 6D FLANGED WHIZ LOCKNUT 2004 Alamo Group Inc. Parts Section 59

62 RAMP CHANNEL 2004 Alamo Group Inc. Parts Section 60

63 RAMP CHANNEL ITEM PART NO. QTY. DESCRIPTION WASHER RIGHT TORSION ROD LEFT TORSION ROD BALE RAMP EXTENSION PIPE STOP TORQ ROD MAIN SUPPORT PAD TORQ ROD CENTER SUPPORT PAD TORQUE ROD END CLAMP TORQUE ROD END BLOCK SPRING ROD RAMP PIVOT BUSHING TORSION ROD MAIN SUPPORT TORSION ROD CENTER SUPPORT Ref CABLE COMPRESSION SPRING RUBBER DONUT CUSHION FLANGED TOP LOCKNUT 18 29N132 2 CABLE THIMBLE BOLT BOLT BOLT BOLT BOLT C 2 LOCKNUT C 2 LOCKNUT NUT NUT NUT LOCKWASHER LOCKWASHER FLATWASHER C 2 LOCKWASHER FLATWASHER 34 15B FLATWASHER Ref WIRE ROPE CLAMP NUT 37 15B FLATWASHER 2004 Alamo Group Inc. Parts Section 61

64 OPTIONAL - WINDROW GATHERING WHEEL 2004 Alamo Group Inc. Parts Section 62

65 OPTIONAL - WINDROW GATHERING WHEEL ITEM PART NO. QTY. DESCRIPTION WINDROW GATHERING WHEEL ASSY GATHERING WHEEL FLANGE CLAMP PLATE WHEEL HUB BOLT LOCKNUT R. SPINDLE L. SPINDLE BOLT C 2 ELASTIC STOP NUT R. STRIPPER & HAY STRAP BOLT FLATWASHER LOCKWASHER HEX NUT R. WHEEL ARM L. WHEEL ARM PIVOT PIN R. MOUNT BRACKET L. MOUNT BRACKET BOLT BOLT LOCKWASHER HEX NUT GREASE FITTING BUSHING BUSHING UPPER LIFT ROD HEX NUT LIFT TUBE LOWER LIFT ROD SPRING ROLL PIN COTTER PIN FLATWASHER HAIR PIN COTTER THRUST WASHER MACHINE BUSHING RETAINING RING 2004 Alamo Group Inc. Parts Section 63

66 WIRE HARNESS ROUTING 2004 Alamo Group Inc. Parts Section 64

67 WIRE HARNESS ROUTING ITEM PART NO. QTY. DESCRIPTION WIRE HARNESS - BALER END WISHBONE WIRE HARNESS 3 5E TY-RAP,.091 X 8" CHANNEL, HARNESS SUPPORT 2004 Alamo Group Inc. Parts Section 65

68 OPTIONAL 1000 RPM CONVERSION KIT ( ) ITEM PART NO. QTY. DESCRIPTION CONNECTOR LINK ROLLER CHAIN SPROCKET CV IID ASSEMBLY (SEE 1000 RPM DRIVELINE) A7C 2 SQUARE HEAD CUP POINT SETSCREW C 2 JAM NUT NOTE: All components 1. Open the 2. Install the 3. Replace the 2004 Alamo Group Inc. Parts Section 66

69 TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT ( Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and 2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and 3. Ensure that each employee uses such Seatbelt while the tractor is moving; and 4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seatbelt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going - especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly - no jerky turns, starts, or stops. 8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.

70 Round Balers Pub Printed U.S.A. P/N 4895WP