for spiral staircases
|
|
- Mervin Patrick
- 5 years ago
- Views:
Transcription
1 Installation instructions Step by Step Instructions for spiral staircases
2 Packing List A. 10 Gauge Track Wire B. 110V AC/12V DC Power Supply C. Tongue Depressor D. Rechargeable Batteries E. LED Light Assemblies F. 20' Roll 3/8" Double Back Tape (for large channel) G. 20' Roll 1/4" Double Back Tape (for small LED wire track) H. 2" Alcohol Swabs I. 5' Power Cord J. Control Box K. 48" LED Wire Channel L. 48" Wire Channel Cover M. 48" Wire Channel D B C E A F G H I J K L M Included tools Phillips Screwdriver Tape Measure Cutter
3 Installation Instructions Spiral Step 1 Locate and remove control box from shipping carton. Turn control box over and remove the screws from bottom of box. Inside the box are two AA battery trays. You will need to install the included 8 AA rechargeable batteries (see tray for correct direction of batteries). After installing the batteries, place cover on control box and reinstall screws. Install the round plug on the transformer into the 12V DC side of the control box and plug the other end into a home 110V AC wall outlet. Step 2 Wipe the flat side of all large wire channels and the small wire track with the alcohol swabs provided in the kit. Let dry completely. Note: It is very important to wipe all channel assemblies prior to installation to ensure proper adhesion Step 3 Apply the larger (3/8") roll of double back tape to the back of all the pieces of the large wire channels, leaving the protective white strip on the tape at this time. Step 4 Apply the small (1/4") roll of double back tape to the small wire track with the slot facing toward you, leaving the protective white strip on the tape at this time. Step 5 Using the alcohol swabs provided, wipe the full length of the backside of the spiral vertical pole next to the welded area and allow to dry completely. Step 6 Attach the large wire channel to the vertical pole on the area just cleaned. Remove the protective white strip from the back of the double backed tape and starting at the top of the pole, stick the track to the pole and press firmly. Leave 1/8" space between wire channel & bottom of tread flange (to allow channel cover to fit over channel).
4 Staircases Step 7 Continue down the pole aligning each 4' section of large wire channel. Cut each 4' section so it ends in the middle of the stair collar. Use the cutter to cut the pieces as shown. Note: Be sure the groove on the channel is facing up when cutting. Right hand up stair Left hand up stair Step 8 The last piece of channel will need to be cut using the cutter provided. Hold channel up to the pole and mark at the bottom of the last stair collar. Note: Be sure the groove on the channel is facing up to cut. Step 9 Install the large wire into the larger wire channel with the lettering facing outward, starting 1/4" from the top and ending 1/4" from the bottom. Cut off the excess wire with the cutter. The wire should lay flat in the channel with no twists. Step 10 Remove lights from bag. Use the alcohol swabs to clean light assembly; allow to dry completely.
5 Step 11 The back of LED light is determined by the direction of its wire, (going left or right), which connects to the large wire track. After determining the direction of the wire left or right, apply 3/8" double back tape to LED light using the cutter provided. Step 12 Start at the top of the stairs. Place the LED light assembly wire around the end of stair tread. Install the plug end of the LED light assembly by placing it over the large wire channel, pressing firmly until the plug latches onto the wire. Repeat for each LED light assembly on the stairs. Step 13 At the bottom of the large wire channel, place the last LED plug assembly one plug width from the bottom of the channel. Below the LED plug, install the plug assembly for the power wire and run it to the control box. Step 14 On same side of control is a 3 position switch AUTO / ON / OFF. AUTO - Turns system on and off automatically based on ambient light conditions ON - System remains on all the time OFF - System is off Note: Control Box should be placed in an area that changes with the room s natural lighting. Turn system to ON to test lights. If the lights are flashing, this is due to the rechargeable batteries not being fully charged. No action is required; the lights will stop flashing once the batteries are fully charged. If they do not light at all, go back to the red and black connector on the side of the control box. Remove the wires and reverse them. Ensure all lights work before continuing. Step 15 Using the alcohol swabs, wipe the underside of the front of all steps. Let dry completely. Step 16 Cut the small wire track into lengths of 14" for small spiral stairs (3'6", 4', 4'6" diameter) or 16" lengths for larger spiral stairs (5', 5'6", 6' diameter).
6 Step 17 Start at bottom stair. Install the small wire track with the slot facing toward you by removing the protective white backing tape from the double back tape. Place under step 1/4" from the center pole or side of stair case, press firmly. LED Step 18 Remove the protective white backing from the double back tape on the back of the LED light and install it at the end of the small wire track by pressing firmly. Step 19 Using the wooden tongue depressor, carefully push the wire from the LED light into the small slot on the front of the small wire track. Repeat steps 17, 18 and 19 until all stairs have tracks and LED lights on them. Step 20 Measure between each plug and cut the channel cover to fit between the plugs to cover the large wire. NOTE: Cut channel cover with groove facing up. Step 21 Turn Control Box switch to AUTO. You re Finished! For Installation help call:
7 ATTENTION: For indoor use only. Spiral stair must have wood tread covering. Do not install in wet areas, unless Water-Resistant Control Box Container is purchased. Use only the provided power supply for the control box. Handle LED plugs carefully. Sharp barbs inside plug may cause injury. Keep kit and all parts out of the reach of children. All remaining scraps and materials should be disposed of properly to prevent injury. Control Box requires 8 AA rechargeable batteries (included with kit) for emergency lighting feature to function. Painting the Stairlighting Kit: If you wish to paint the cover and LED assembly it should be done prior to cutting into pieces. Wipe all parts with alcohol swabs provided. Latex, enamel or acrylic paints recommended (spray or brushed). Do not paint over LED lights. Do not paint over metal barbs on plugs. Use masking tape to protect LED lights and barbs.
8
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 24813 UNDER 2004 TSX Issue Date APRIL 2003 PARTS LIST Rear under spoiler 2 Short step bolts TOOLS AND SUPPLIES REQUIRED Phillips screwdriver
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory DECK LID SPOILER Application 2014 RLX Publications No. BII 13399 Issue Date JAN 2013 PARTS LIST Trunk spoiler Left trunk spring (marked yellow) Right trunk spring (marked
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27955 SIDE 2005 CIVIC SI Issue Date AUG 2004 PARTS LIST Left side under spoiler Right side under spoiler 6 Plates 8 Clips Template INSTALLATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08P20-STX-200A Application 2010 MDX Publications No. BII 42020 Issue Date JAN 2010 PARTS LIST Door edge film LF Door edge film RF Door edge film LR Door edge film
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory WELL P/N 08P21-STX-200A Application 2012 MDX Publications No. BII 46618 Issue Date OCT 2011 PARTS LIST Left front fender trim Bracket A-L Left front bumper trim Bracket
More informationSUT-450-I ASSEMBLY REQUIREMENTS
SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt
More informationRev TOOLS & MATERIALS REQUIRED QTY 3D PART NO. DESCRIPTION
Rev. 04-10 QTY 3D PART NO. DESCRIPTION 1 691609 FRONT BUMPER REPLACEMENT 1 691610 RIGHT SIDE SKIRT 1 691611 LEFT SIDE SKIRT 1 691612 REAR LOWER SKIRT 4 3M 94 3M ADHESION PROMOTER 16 #8 X ¾ SELF DRILLING
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. 2009 CIVIC HYBRID All 40191 Issue Date AUG 2008 PARTS LIST Rear under spoiler 2 Step bolts 4 Self-tapping screws TOOLS REQUIRED Phillips
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory INTERIOR S P/N 08Z03-TX4-210A Application 2017 RDX Publications No. VERSION 1 Issue Date FEB 2016 PARTS LIST Right rear door panel Dashboard right panel Left rear door
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08P48-T3L-100 Application 2013 ACCORD 2-DOOR Publications No. AII 13018 Issue Date OCT 2012 PARTS LIST Rear bumper applique Illustration of the Rear Bumper Applique
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REAR SPOILER Application 2011 CR-Z MUGEN Publications No. AII 45919 Issue Date APRIL 2011 PARTS LIST Right wing bracket Rear wing Left wing bracket Right wing base Right
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 33322-36889 UNDER 2007 TL Issue Date MAY 2007 PARTS LIST Front under spoiler Left bracket (Marked L ) Right bracket (Marked R ) 8 Self-tapping
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. FENDER FLARES P/N 08P21-S3V-200 2003 MDX BII 24553 Issue Date SEP 2002 PARTS LIST Right rear fender flare Left front fender flare Right
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 25852 PILOT Issue Date AUG 2003 PARTS LIST INSTALLATION NOTE: Door visor (Front left) These instructions show the left door visors being
More informationInstruction Manual. Specification:
Instruction Manual L O W Specification: Wingspan: 133 cm (52.3 inches) Length : 104 cm (40.9 inches) Weight : 1790gr Engine : 25-32 two stroke Radio : 4 channel - 4 servo W I N G KIT CONTENTS: We have
More informationPRODUCT MANUAL Gecko Wireless 2 Zone LED Dimmer and Receiver
Product Description The Gecko Wireless 2 Zone Wall LED Dimmer has been designed to bring light control easily. No wires or switch box locations are needed, just stick or mount the Gecko to any flat location
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08P21-STX-200 2008 MDX BII 37680 Issue Date AUG 2007 PARTS LIST Left bracket A Left front fender flare Left bracket B Left front bumper
More informationPRODUCT MANUAL Gecko Wireless One Zone LED Dimmer and Receiver
Product Description The Gecko Wireless One Zone Wall LED Dimmer has been designed to bring light control easily. No wires or switch box locations are needed, just stick or mount the Gecko to any flat location
More informationContinuous Cord Loop Designer Series Roller Shades
Shade Maintenance Leveling a Crooked Shade 1. Pull down shade until roller is exposed. Do not pull further to avoid pulling cloth off roller. 2. Stick a 5" strip of masking tape into the roller at opposite
More informationLarge Case Storage - Replacing Case Lock System
Large Case Storage - Replacing Case Lock System 1 Table of Contents If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate
More informationInstallation Instructions: Side Delivery Units BDS-2555
Installation Instructions: Side Delivery Units BDS-2555 X-Calibur Units Installation Instructions for BDS-2555 X-Calibur Dental Units 7-18-06 BDS Side-Delivery Unit Installation Time: Approximately 1
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SIDE UNDER S Application 2013 CIVIC 2-DOOR Publications No. AII 13069 Issue Date NOV 2012 PARTS LIST 4 Flare nuts Left spoiler 2 Washer-nuts Right spoiler 2 Screws 2
More informationPLEASE READ THESE INSTRUCTIONSFULLY BEFORE STARTING TO ASSEMBLE YOUR DIDICAR PLEASE PAY SPECIAL ATTENTION TO THE NOTES AND HINTS
PLEASE READ THESE INSTRUCTIONSFULLY BEFORE STARTING TO ASSEMBLE YOUR DIDICAR PLEASE PAY SPECIAL ATTENTION TO THE NOTES AND HINTS ASSEMBLY INSTRUCTIONS Parts List iv) i) v) ii) iiib) iiia) vii) i) Car Body
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PRTS INSTLLTION INSTRUCTIONS DESCRIPTION: PPLICTION: PRT NUMBER: KIT CONTENTS: Side Window Deflector Quest (2011) H0800 1J00 Item Qty. 1 B 1 C 1 D 1 E 4 F 4 G 1 Part Description Side Window Deflector
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2011 CIVIC 4-DOOR Si Publications No. AII 44423 Issue Date AUG 2010 PARTS LIST Template Front under spoiler TOOLS AND SUPPLIES REQUIRED 4 Self-tapping screws
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24081 ACCORD 2-DOOR Issue Date SEP 2002 PARTS LIST INSTALLATION NOTE: Rear under spoiler Be careful not to damage the rear bumper and
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Versa Note 999F3 4Z000 - Accent Lighting Kit. 999Q9 AY000 - Accessory Service Connector
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory EDGE P/N 08P20-TX4-200 Application 2018 RDX Publications No. VERSION 1 Issue Date MAY 2017 PARTS LIST TOOLS AND SUPPLIES REQUIRED Left front door edge film Shop towel
More informationINSTALLATION INSTRUCTIONS www.collegehillshonda.com Accessory P/N 08P21-SZA-100 Application 2009 PILOT Publications No. AII 39455 Issue Date MAY 2008 NOTE: The fender trim cannot be installed on vehicles
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08E12-T2A-100A Application 2014 ACCORD 4-DOOR Publications No. AII 49975 Issue Date AUG 2013 PARTS LIST Right front door sill trim Illustration of the Door Sill
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application CR-V Publications No. AII 12065 Issue Date DEC 2011 PARTS LIST Left front body side molding Right front body side molding TOOL AND SUPPLIES REQUIRED Masking
More informationLightRider. Instructions for Power Link Helmet Light. Helmet Vertical Midline
LightRider Instructions for Power Link Helmet Light Helmet Vertical Midline Look at the back of your helmet. Then imagine a vertical line that runs up the back and divides your helmet into right and left
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory BODY S Application 2015 CIVIC 4- Publications No. VERSION 1 Issue Date SEPT 2014 PARTS LIST Left front body side molding (marked FR-L) Right front body side molding
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 41770 2010 RL P/N 08R04-SJA-201 Issue Date JUNE 2009 PARTS LIST INSTALLATION NOTE: Door visor (front left) These instructions show the
More informationCBT25, 50 & 100 driveshaft
CBT25, 50 & 100 driveshaft replacement 2 CBT driveshaft REPLACEMENT Revision History rev. level 01_03.13.2014 NOTE: due to the fact that a new machine (never exposed to seed treatment) was used to demonstrate
More informationSolar & Roller Shades
STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades Loop Control, Loop Control with Cassette/2 on 1 Headrail & Loop Control with Metal Valance Table of Contents Step 1 - Getting Started....3 Everything
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Left front trim piece
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33173 UNDER 2007 ODYSSEY Issue Date JULY 2006 PART LIST Front under spoiler 5 Stepped bolts TOOLS AND SUPPLIES REQUIRED Phillips screwdriver
More informationMaintenance Information
Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 44686 2011 RL P/N 08R04-SJA-201 Issue Date DEC 2010 PARTS LIST INSTALLATION NOTE: Door visor (front left) These instructions show the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. UNDER 2007 CIVIC SI All 33529 Issue Date AUG 2006 PARTS LIST Rear under spoiler Clip Rubber washer 6 Flange bolts 6 Flange nuts TOOLS REQUIRED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08R04-TK6-100A Application 2012 FIT Publications No. AII 45990 Issue Date AUG 2011 PARTS LIST Door Visors cannot be installed on a vehicle equipped with the accessory
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. All 40290 BODY SIDE 2009 RIDGELINE Issue Date AUG 2008 PARTS LIST INSTALLATION NOTE: Be careful not to damage the body paint finish. Left
More informationGENUINE MUD FLAP (FRONT)
GENUINE MUD FLAP (FRONT) INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a Genuine Mazda Accessory. Before removal and installation, be sure to thoroughly read these instructions. Please
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SIDE S P/N 08F04-SZT-1T0 Application 2011 CR-Z Publications No. AII 43563 Issue Date AUG 2010 PARTS LIST Left side under spoiler Illustration of the Side Spoilers Installed
More informationSoap/Sanitizer Dispensers
Soap/Sanitizer Dispensers Installation & Operating Instruction Manual Thoroughly read this instruction booklet before operating Sloan dispensers. Keep this Installation & Operating Instruction Manual with
More informationLMT Lens/Optics Cleaning Procedure. Lens Cleaning Procedure
SVC-LMT-Procedure REV. TBD Product Support Engineer: Effective: Sheet: MP 04/13/11 Pg. 1 of 10 Lens 1. Assemble the following cleaning components as depicted in Figure 1. Alcohol Canned Dry Air Nozzle
More informationCordless Rechargeable Saw Instructions for Use
Technical data Voltage: DC 10.8V Weight: 1.25Kg Stroke rate: 0-2100/min Stroke: 15mm Cutting capacity: max diameter in wood 80mm / in soft metal 7mm Charging time: Between 5.0-5.5 Hours Battery: 1.3Ah
More informationSoap/Sanitizer Dispensers
Soap/Sanitizer Dispensers Installation & Operating Instruction Manual Thoroughly read this instruction booklet before operating Sloan dispensers. Keep this Installation & Operating Instruction Manual with
More informationCOYOTE Dome Closure 9.5" x 28" with Transition Tray for High Density Splice Applications
OCTOBER 2017 COYOTE Dome Closure 9.5" x 28" with Transition Tray for High Density Splice Applications Be sure to read and completely understand this procedure before applying product. Be sure to select
More informationIncluded in Hardware Kit. Rear Corners 2-Door. Jeep JK Trail Armor. Set Part #14009 Rev STEP 1 - PRIOR TO INSTALLATION
Jeep JK Trail Armor Set Part #14009 Rev-2 02-23-11 A) B) C) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the trail armor according to these written instructions with the hardware
More informationCommand Center. Model Number Helicopter, Motorcycle, equipment packs and figures sold separately.
Command Center Model Number 72955 Helicopter, Motorcycle, equipment packs and figures sold separately. Please keep these instructions for future reference. Adult assembly is required. Requires three, size
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS SIDE S 2013 TSX BII 13496 Issue Date SEP 2012 PARTS LIST 4 Screws Left side under spoiler Right side under spoiler 2 Clamps TOOLS AND SUPPLIES
More informationWXGUARD WIND SEGMENTED LIGHTNING DIVERTER STRIPS INSTALLATION GUIDE.
WXGUARD WIND SEGMENTED LIGHTNING DIVERTER STRIPS INSTALLATION GUIDE www.wxguardwind.com Shine Wire Products, Inc. 25 Print Works Drive Adams, MA 01220 1-800-543-5151 www.shinewire.com WXGuard is the new
More informationFlexJet - Flex Cable Replacement
P/N: 109515R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 FlexJet - Flex Cable Replacement Notices: Warning! Ensure that all AC power cables are removed from the printer
More informationlkm7001 key override module Installation Instructions Converting The LKM7000 to The LKM7003
lkm7001 Instructions Converting The LKM7000 to The LKM7003 key override module In A Single Motion, We ll Change The Way You Think About Security Read Instructions thoroughly prior to installation Base
More informationsection INDOOR CYCLE COMPUTER INSTRUCTIONS
section INDOOR CYCLE COMPUTER INSTRUCTIONS 1 INSTALLING THE COMPUTER 1) Computer Bracket The Computer Bracket mounts to the underside of the handlebar. The easiest method of installation is to remove the
More informationINSTALLATION INSTRUCTIONS PARTS LIST. SUPPLIES REQUIRED Isopropyl alcohol Shop towel Masking tape Tape measure. Door visor (front left) INSTALLATION
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 13348 2013 RIDGELINE P/N 08R04-SJC-100 Issue Date SEP 2012 PARTS LIST Door visor (front left) SUPPLIES REQUIRED Isopropyl alcohol Shop
More informationINSTALLATION INSTRUCTIONS Accessory S P/N 08R04-SWA-100 Application 2010 CR-V Publications No. AII 42599 Issue Date AUG 2009 NOTE: Visors may not be legal in all states. Please check the laws of your state
More informationRugged Ridge Spartacus HD Tire Carrier Kit Install
Rugged Ridge Spartacus HD Tire Carrier Kit Install Installation Time: 2 hours Tools Required: Ratchet ¾ socket 19 mm socket 13 mm socket 10 mm socket 19 mm Wrench 10 mm wrench 6mm Allen Wrench T50 torx
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08P48-TZ5-200 Application 2014 MDX Publications No. BII 48832 Issue Date MAY 2013 PARTS LIST Rear bumper applique Applicator INSTALLATION NOTE: Do not damage the
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationTop Down Rollstar Shade Installation Instructions
Top Down Rollstar Shade Installation Instructions Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the dimensions you specified. With proper
More informationS6 BATTERY REPLACEMENT
S6 BATTERY REPLACEMENT Supplemental Instruction Guide P/N 108304 Battery Pack Removal Tools Required: S6 Operation & Parts Manual, Phillips Head Screwdriver, Needle Nose Pliers, Wire Stripping / Crimping
More informationSupply Valve Replacement
This procedure is to help facilitate the replacement of the25.1-25.4 supply valves. Solenoid Supply Valves Note: You will need the following tools: Socket Wrench with extension and a 3/8 Socket Size 1
More informationExpedition Front Bumper Instructions
Expedition Front Bumper Instructions QTY 3D PN. FCS PART NUMBER DESCRIPTION 1 691256 A 8 E X D - 1 7 B 635-AAPLN FRONT BUMPER REPLACEMENT HARDWARE SUPPLIED 10 SELF TAPING SCREWS -10 for Front Bumper PLASTIC
More informationInstallation Instructions: Swing Mounted Units BDS-2575
Installation Instructions: Swing Mounted Units BDS-2575 X-Calibur Units Installation Instructions for BDS-2575 X-Calibur Dental Units 8-23-10 BDS Swing Mounted Units Installation Time: Approximately 2
More informationTOYOTA TACOMA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item
More informationENGLISH: Original instructions INSTRUCTION MANUAL. Cordless Cleaner CL106FD. Read before use.
ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Cleaner CL06FD Read before use. WARNING This appliance can be used by children aged from 8 years and above and persons with reduced physical,
More informationPart Numbers: TTU-BGP14 & TTU-BGB14
Date: 10.14.2015 TOYOTA TUNDRA 2014-17 Billet Grille Part Numbers: TTU-BGP14 & TTU-BGB14 Grille Hardware Bag Contents Item # Quantity. Description 1 6 U-Nuts 2 8 #10 Screws 3 2 #8 Screws 4 2 2 Flange Brackets
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24642 BODY SIDE CLADDING 2003 CR-V P/N 08P21-S9A-100 Issue Date OCT 2002 PARTS LIST Right rear bumper piece Right front fender piece
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2012 CIVIC 4-DOOR Publications No. AII 45625-46263 Issue Date MAY 2011 PARTS LIST Trunk spoiler Left trunk spring (marked yellow) Template 4 Clip grommets
More informationPreparation for an Extended Idle Period of the GT-381/361
Preparation for an Extended Idle Period of the GT-381/361 If the printer is not to be used for an extended period of time, the white print heads and ink tubes will still need to be maintained. The tube
More informationSkill Level 3 Average Skills Needed. Made In USA. Kit #04997 Skill Level 4. Zephyr Parts List
Kit #04997 Skill Level 4 Made In USA Zephyr Parts List Item # Item Name Qty 10137 Engine Mount Tube (AT-38/11) 1 10218 Airframe Body Tube (AT-98/18) 4" Thick Wall 1 10219 Airframe Body Tube (AT-98/18)
More informationInstallation Instructions Supertop NX Twill
Installation Instructions Supertop NX Twill Vehicle Application: Jeep Wrangler Unlimited 2007-current Part Number 54823 Installation Tips Before you begin installing your new Supertop NX Twill, please
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory (WITH TEMPLATE) Application 2010 TL Publications No. BII 42533-44799 Issue Date AUG 2010 PARTS LIST Right rear under spoiler 4 Self-tapping screws 10 Seals Left rear
More informationTOYOTA RAV TVIP V3
Section I Installation Preparation Part Number: 08586-4A872 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4 1 V3
More informationCellular Shades MOTORIZED SHADE Top Down - Bottom Up. Installation & Care Instructions
Cellular Shades MOTORIZED SHADE Top Down - Bottom Up ucontact@udoblinds.com 1-855-205-8442 Installation & Care Instructions 152746A 7/2/2018 GETTING STARTED A few simple tools are required: - Measuring
More informationSylvania 7.5' Pre-Lit Troy Fir Tree LED Color Changing and Multi Function One Plug Tree Tree ID #T1, Item # V
Sylvania 7.5' Pre-Lit Troy Fir Tree LED Color Changing and Multi Function One Plug Tree Tree ID #T1, Item # V67656-13 Thank you for purchasing this tree. This tree assembles in minutes and is decorated
More informationCervini's Functional Ram Air Kit (05-09) - Installation Instructions
Cervini's Functional Ram Air Kit (05-09) - Installation Instructions The below installation instructions work for the following products: Cervini's Functional Ram Air Kit for 05-09 Ram Air Hood Cervini's
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SPOILER (DECK LID) ACCORD 4-DOOR AII 24063 Issue Date AUG 2002 PARTS LIST Trunk spoiler Right trunk spring (marked green) Left trunk spring
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SPOILER (LOW) ACCORD 4-DOOR AII 30276 Issue Date AUG 2005 PARTS LIST Trunk spoiler Right trunk spring (marked green) Left trunk spring (marked
More informationDouble-check to ensure that all of the parts are included in your shipment. Please immediately contact 3dCarbon if you are missing any part.
5 Pc. Kit Includes QTY 3D PN. DESCRIPTION 1 691815 CRUZE FRONT AIR DAM POLYURETHANE PRE-PRIMERED 1 691816 CRUZE SIDE SKIRT RH POLYURETHANE PRE-PRIMERED 1 691819 CRUZE SIDE SKIRT LH POLYURETHANE PRE-PRIMERED
More informationOreck Magnesium Series Service Manual. The Oreck Manufacturing Company
Oreck Magnesium Series Service Manual The Oreck Manufacturing Company 08/2012 10/2011 The Oreck Manufacturing Company Contents Covering all Magnesium Upright Models Including: LW100, LW125, LW1000, AND
More informationPart Number: TBL-016S
5/18/17 TOYOTA TUNDRA 2014-2017 LED Truck Bed Light Kit Part Number: TBL-016S Kit Contents Item # Quantity Reqd. Description 1 2 LED Bed Light Harness (10 ) 2 2 LED Bed Light Harness (5 ) 3 1 Y Harness
More informationAF7006 Alarming Camera Display Unit (6.5 ) AF7015 Alarming Camera Display Unit (4.5") AF7216 Camera Sensor
How to Setup a Display Unit AF700 or AF70 AF7 AF700 Alarming Camera Display Unit (. ) AF70 Alarming Camera Display Unit (.") AF7 Camera Sensor Battery-powered alarming system with AC power connections
More informationBe sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application.
5 NOVEMBER 2010 COYOTE Dome 9.5 x 28 Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application. 1. 7. 2. 4. 10.
More informationAggressive Chin Spoiler CDC#
Note: 2005-2009 Aggressive Chin Spoiler CDC# 110021 Read installation instructions before starting and test fit component before painting. Chin Spoiler is a molded Urethane part. To ensure the quality
More informationRoller Shades MOTORIZED SHADE. Simplicity. Installation & Care Instructions
Roller Shades MOTORIZED SHADE Simplicity Installation & Care Instructions 152140 J 1/13/2016 GETTING STARTED A few simple tools are required: - Measuring tape - Power drill, drill bits - 1 4 Hex head and/or
More information2005+ Mustang Trunk Lid Release and Trunk Lights Installation
There is no warranty expressed or implied by this document, you follow these instructions at your own risk. These instructions worked for me, but your experience may vary. The final product of these instructions
More informationINSTALLATION INSTRUCTIONS SERVICE MANUAL
INSTALLATION INSTRUCTIONS SERVICE MANUAL This manual provides instructions for the proper installation of the L 06 HAWLE stair lift. It is necessary to read and understand the contents of these instructions
More informationWheelieSafe. WheelieSafe. User Manual. Motorized Trolley. Distributor:
WheelieSafe Motorized Trolley WheelieSafe Distributor: User Manual You must read this manual before using your WheelieSafe trolley P/N: 9023100 Rev. 01/16 Table of contents Contents Pages Safety Symbols,
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
LIGHTPATH SERIES LOW LEVEL FULLY RECESSED LED EMERGENCY LIGHT 1. 2. 3. 4. 5. 6. 7. 8. INSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always
More information05 09 Mustang Squirter Nozzle Relocation Kit CDC #112050
05 09 Mustang Squirter Nozzle Relocation Kit CDC #112050 Note: Read installation instructions before starting. Component Check List: Quantity/Description Part# CDC Installer 2 - Squirter Nozzles 115063
More informationENGLISH (Original instructions) INSTRUCTION MANUAL. Cordless Cleaner DCL140 DCL180. IMPORTANT: Read Before Using.
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Cleaner DCL40 DCL80 009983 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DCL40 DCL80 Capacity 650 ml Continuous
More informationPowerPlex 14in 40V MAX String Trimmer
Form No. 3417-958 Rev C PowerPlex 14in 40V MAX String Trimmer Model No. 51482 Serial No. 318000001 and Up Model No. 51482T Serial No. 318000001 and Up Register at www.toro.com. Original Instructions (EN)
More informationJ5242.
J5242 Product features and decoration may vary from the photograph. Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Requires three
More information