|
|
- Ira Gallagher
- 5 years ago
- Views:
Transcription
1 Page 1 of 6 Section 03-01C: Engine 3.4L SHO 1999 Taurus/Sable Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/25/1998 Intake Manifold Upper Removal 1. Disconnect battery ground cable (14301). Refer to Section Remove engine appearance cover as described. 3. Remove right half of cowl top vent screen as described in Section Remove throttle body (9E926) as described in Section 03-04C. 5. Disconnect the main emission vacuum supply hose from the surge tank vacuum fitting and EGR valve (EGR valve) (9D475). Position vacuum supply hose out of the way. 6. Disconnect vacuum tube from intake manifold vacuum union. 7. Remove the two retaining bolts for the transducer mounting bracket (9J432) from the surge tank. Position the transducer mounting bracket out of the way. 8. Remove the two intake manifold supports (9J444) from the surge tank and cylinder head (6049). Transducer Mounting Bracket and Intake Manifold Support Installation Bolt (2 Req'd) 2 9J432 Transducer Mounting Bracket 3 A9908 Stud Bolt (2 Req'd) Bolt (2 Req'd) 5 9J444 Intake Manifold Support (2 Req'd) 6 9D477 EGR Valve to Exhaust Manifold Tube 7 9D475 EGR Valve B Tighten to Nm (19-25 Lb-Ft) 9. Remove EGR valve. Refer to In-Vehicle Service in Section Remove retaining bolts and surge tank stay from front of surge tank. 11. Remove bolt, nuts and surge tank stay from rear of surge tank. 12. Disconnect crankcase ventilation tube (6758) from valve cover (6582). 13. Disconnect crankcase ventilation tube from surge tank. 14. Disconnect vacuum tube to fuel pressure regulator (9C968). 15. Remove power steering pressure hose-to-surge tank retainer. 16. Disconnect RH crankcase ventilation hose (6853) and position aside. 17. Remove heater hose bracket-to-surge tank retainers.
2 Page 2 of Loosen intake air connector hose clamps and remove surge tank from engine. Surge Tank Installation Intake Manifold Hose Clamp Flange Bolt 4 9J444 Rear Surge Tank Stay Nut Stud Bolt 7 9J444 Front Surge Tank Stay Bolt Bolt 10 9F722 Air Tube to Throttle Body Hose (2 Req'd) B Tighten to 5-7 Nm (45-61 Lb-In) 19. Remove radio ignition interference capacitor bracket retaining bolt and position radio ignition interference capacitor (18801) aside. 20. CAUTION: When removing engine components, always remove retaining bolts in reverse of tightening sequence (as shown) or damage to engine components may occur. Remove intake manifold retaining bolts in standard loosening sequence. 21. Remove upper intake manifold (9424) and intake manifold upper gaskets (9H486) from lower intake manifold and discard intake manifold upper gaskets. Installation 1. CAUTION: New upper intake manifold gaskets must be used or damage to the engine may occur. Position new upper intake manifold gaskets on lower intake manifold. 2. CAUTION: Upper intake manifold bolts must be tightened in sequence shown or damage to the engine may occur. Position upper intake manifold on lower intake manifold and install retaining bolts. Tighten bolts in standard tightening sequence to Nm (14-20 lb-ft). 3. Install radio ignition interference capacitor bracket and retaining bolt. Tighten retaining bolt to 8-12 Nm ( lb-in). 4. Position surge tank on engine and align intake air connector clamps as shown. Tighten clamps securely. Intake Air Connector Hose Clamp Orientation
3 Page 3 of 6 Surge Tank Installation Intake Manifold Hose Clamp Flange Bolt 4 9J444 Rear Surge Tank Stay Nut Stud Bolt 7 9J444 Front Surge Tank Stay Bolt Bolt 10 9F722 Air Tube to Throttle Body Hose (2 Req'd) B Tighten to 5-7 Nm (45-61 Lb-In) 5. Install heater hose bracket-to-surge retainers. 6. Connect RH crankcase ventilation hose. 7. Install power steering pressure hose bracket-to-surge retainer. 8. Connect vacuum tube from fuel pressure regulator to surge tank fitting. 9. Connect crankcase ventilation tube to surge tank fitting. 10. Connect crankcase ventilation tube to valve cover. 11. Install rear surge tank stay and retaining bolts and two nuts. Tighten bolt and nuts to Nm (14-20 lb-ft). 12. Install front surge tank stay and retaining bolts. Tighten retaining bolts to Nm (14-20 lb-ft).
4 Page 4 of Install EGR valve. Refer to In-Vehicle Service, Section Install two intake manifold supports from surge tank to cylinder head. Tighten retaining bolts to Nm (14-20 lb-ft). 15. Position transducer mounting bracket on surge tank and install retaining bolts. Tighten bolts to Nm (14-20 lb-ft). Transducer Mounting Bracket and Intake Manifold Support Installation Bolt (2 Req'd) 2 9J432 Transducer Mounting Bracket 3 A9908 Stud Bolt (2 Req'd) Bolt (2 Req'd) 5 9J444 Intake Manifold Support (2 Req'd) 6 9D477 EGR Valve to Exhaust Manifold Tube 7 9D475 EGR Valve B Tighten to Nm (19-25 Lb-Ft) 16. Connect vacuum tube to intake manifold vacuum union. 17. Connect main emission vacuum supply hose to the surge tank fitting and EGR valve. 18. Install throttle body as described in Section 03-04C. 19. Install right half of cowl vent screen (018A16). Refer to Section Install engine appearance cover as described. 21. Connect battery ground cable. Refer to Section Lower Removal 1. Relieve fuel system pressure. Refer to Section 03-04C. 2. Disconnect battery ground cable. Refer to Section Remove upper intake manifold as described. 4. Disconnect fuel supply and return lines from fuel injection supply manifold (9F792). Refer to Section 03-04C. 5. Disconnect intake manifold runner control deactivation cable from lower intake manifold (IMRC). Remove cable from bracket and position aside. Intake Air Connector Hose Clamp Orientation
5 Page 5 of 6 6. Disconnect engine control sensor wiring (12A581) from fuel injectors (9F593) and wiring retainers. Position engine control sensor wiring out of the way. 7. If required, remove fuel injection supply manifold and fuel injectors from lower intake manifold (IMRC). Refer to Section 03-04C. 8. Remove lower intake manifold to cylinder head retaining bolts. 9. Remove lower intake manifold (IMRC) from cylinder heads Bolt 2 9L490 Lower Intake Manifold (IMRC) Intake Manifold Gasket Cylinder Head A Tighten Nm (14-20 Lb-Ft) 10. Remove intake manifold gaskets (9439) from cylinder heads and discard intake manifold gaskets. Installation 1. NOTE: Verify operation of intake manifold runner control plate operation. Follow removal procedure in reverse order using new intake manifold gaskets. 2. Tighten lower intake manifold retaining bolts to Nm (14-20 lb-ft). 3. Connect fuel supply and return lines. Refer to Section
6 Page 6 of 6
1999 F-150/250 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 4.6L and 5.4L IN-VEHICLE REPAIR Procedure revision date: 02/03/1999 Intake Manifold Lightning Removal WARNING: Do not smoke or carry lighted tobacco or open flame of
More information2001 Lincoln LS Workshop Manual
Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional
More information1998 F-150/250 Workshop Manual
Page 1 of 13 SECTION 303-01B: Engine 4.6L and 5.4L 1998 F-150/250 Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 03/07/2000 Intake Manifold Removal WARNING: Do not smoke or carry lighted tobacco
More information10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
More informationPage 1 of 6 Section 303-01A: Basic Engine 4.2L REMOVAL 1997 F-150/250 Workshop Manual Engine Special Service Tool(s) Engine Lifting Bracket or equivalent 014-00730 Removal 1. Remove the hood. 2. On A/C
More informationDISASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
More information2006 F-Super Duty Workshop Manual. Installation. All vehicles. Install the glow plug. Tighten to 19 Nm (14 lb-ft).
Installation All vehicles 1. Install the glow plug. Tighten to 19 Nm (14 lb-ft). 2. Clean and apply clean engine oil to the O-rings. 3. Using the special tool, install the glow plug harness. Vehicles equipped
More information2002 Mustang Workshop Manual
Page 1 of 13 SECTION 303-01B: Engine 4.6L (2V) 2002 Mustang Workshop Manual REMOVAL Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Remover, Crankshaft Vibration Damper 303-009 (T58P-6316-D)
More informationIN-VEHICLE SERVICING > VALVE COVER - RH
Page 1 of 20 Service Manual: ENGINE - 5.4L (3V)- F-150 & MARK LT IN-VEHICLE SERVICING > VALVE COVER - RH 2008 Ford Pickup 5.4L Eng F150 Material Item Specification Motorcraft Metal Surface Prep ZC-31 PAG
More information2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar
COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top
More informationValve Cover - RH Material
1 of 5 5/15/2015 8:06 AM Valve Cover - RH Material 2 of 5 5/15/2015 8:06 AM 3 of 5 5/15/2015 8:06 AM Removal CAUTION: During engine repair procedures, cleanliness is extremely important. Any foreign material,
More informationPage 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description
More information1999 E-Series Workshop Manual
http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998
More information2007 Escape/Mariner/Escape Hybrid/Mariner Hybrid Workshop Manual
SECTION 303-08A: Engine Emission 2007 Escape/Mariner/Escape Hybrid/Mariner Hybrid Control 2.3L Positive Crankcase Ventilation (PCV) System Components Exploded View View (157 KB) Printable Item Part Number
More informationPage 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft
More informationIntake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
More information2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 9 SECTION 303-04: Fuel Charging and Controls 2002 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/13/2001 Fuel Injection Supply Manifold Material
More informationIntake Manifold Replacement
Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may
More informationDESCRIPTION AND OPERATION
303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589
More information2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
More informationPage 1 of 6 Fuel Charging and Controls - Turbocharger - 2.7L V6 - TdV6 - Turbocharger RH Removal and Installation Special Tool(s) Engine support beam 303-021 Engine lifting brackets 303-1129 Removal 1.
More information2/13/2018 Engine 3.0L (4V) - Valve Cover RH - in Vehicle Repair 2006 Lincoln Zephyr MotoLogic
2006 Zephyr Applies to: 3.0L (4V) Report a problem with this article SECTION 303-01B: Engine 3.0L (4V) 2006 Fusion/Milan/Zephyr Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/24/2006 Valve
More informationSTARTER COMPONENTS FOR REMOVAL AND INSTALLATION
Removal STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Starter Components For Removal And Installation REMOVAL OF STARTER 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started
More information2003 Taurus/Sable Workshop Manual
Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)
More informationIntake Manifold Removal
PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS Parts included: -GT350 Intake manifold M-944-M5 -GT350 Air bucket w/filter.
More information2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
More informationPage 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground
More information2011 Mercury Grand Marquis LS
Fig. 6: Locating Intake Manifold Crash Bracket With Tie Strap 24. Remove the intake manifold crash bracket bolt. 25. Disconnect the fuel rail pressure and temperature sensor vacuum and electrical connectors.
More informationIN-VEHICLE REPAIR. Upper Intake Manifold
303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric
More informationFUEL PRESSURE REGULATOR
EG2214 3VZE ENGINE FUEL PRESSURE REGULATOR ONVEHICLE INSPECTION CHECK FUEL PRESSURE (See step 2 on page EG2206) COMPONENTS FOR REMOVAL AND INSTALLATION FUEL PRESSURE REGULATOR REMOVAL 1. DISCONNECT NEGATIVE
More information10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic
2007 Yukon Denali Applies to: 4.8L, 5.3L, 6.0L and 6.2L Report a problem with this article Removal Procedure 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Resonator Outlet Duct Replacement.
More information2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper
More informationASSEMBLY/INSTALLATION INSTRUCTIONS
ASSEMBLY/INSTALLATION INSTRUCTIONS AURORA 3000 & 4000 SCORPION TURBO SYSTEM NOTICE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath
More informationIntake Manifold Replacement
Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:
More informationPage 1 of 8 303-01A Engine 2.3L 2007 Escape/Mariner/Escape Hybrid/Mariner Hybrid IN-VEHICLE REPAIR Procedure revision date: 10/05/2008 Cylinder Head Special Tool(s) Alignment Plate, Camshaft 303-465 (T94P-6256-CH)
More informationCylinder Head Replacement
CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A
More information1996 Mustang. 1. Remove air cleaner outlet tube (9B659). Refer to Section Disconnect battery ground cable (14301). Refer to Section
REMOVAL AND INSTALLATION Fuel Charging Wiring Removal and Installation 1. Remove air cleaner outlet tube (9B659). Refer to Section 03-12. 2. Disconnect battery ground cable (14301). Refer to Section 14-01.
More informationINTAKE MANIFOLD INSPECTION/REPLACEMENT
ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.
More informationM-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. WARNING: CUSTOM CALIBRATION REQUIRED! CALIBRATION NOT INCLUDED! KIT CONTENTS: 1) Intake Manifold Assembly 2) Assembly
More informationCylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty
More information2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section
Exhaust Gas Recirculation (EGR) Valve 2.3L 1. Drain the cooling system. For additional information, refer to Section 303-03. 2. Disconnect the battery ground cable. For additional information, refer to
More informationIntake Manifold Replacement
Page 1 of 13 Your Current Vehicle: 2008 Cadillac STS Intake Manifold Replacement Intake Manifold Replacement Removal Procedure 1. Turn the ignition OFF. 2. Remove the fuel injector sight shield. Refer
More informationFREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How
1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines
More information1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
More informationREMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Valve Cover» Service and Repair» Procedures» RH Valve Cover RH Removal 1. Disconnect the battery ground cable. 2. Remove the air cleaner
More informationDISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.
303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773
More informationEngine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
More informationPage 1 of 8 SECTION 303-01A: Engine 2.3L 2002 Ranger Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/20/2004 Intake Manifold Removal 1. Remove the accelerator control snow shield. 2. Remove
More informationEngine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A)
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/23/2008 Engine Front Cover Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Installer, Front
More informationIN-VEHICLE SERVICE. Engine Components
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown
More information2000 Chrysler SEBRING
2000 Chrysler SEBRING Submodel: JX Engine Type: V6 Liters: 2.5 Fuel Delivery: FI Fuel: GAS 2.0L SOHC and 2.4L DOHC Engines The intake manifold for the 2.0L SOHC engine is a long branch design made of a
More informationEngine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
More informationASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
More information2007 Ford Freestyle SEL
Fig. 279: Exploded View Of Engine Heads, Intake & Exhaust Components Item Part Number Description 1 9D475 Exhaust gas recirculation (EGR) system module 2 9D477 EGR module tube 3 9F485 RH exhaust manifold
More informationIntake Manifold Replacement
ALLDATA Online - 2001 Cadillac DeVille V8-4.6L VIN 9 - Intake Manifold Replacement Page 1 of 15 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's
More informationFuel Injector ( )
Published: Mar 29, 2010 Fuel Injector (196010) Special Service Tools Fuel Injector remover 303-1127 Removal WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near
More information8/28/2018 Engine 6.0L Diesel - Cylinder Head RH - in Vehicle Repair 2006 Ford F-550 MotoLogic. Specification
2006 F-550 Applies to: 6.0L Diesel Report a problem with this article SECTION 303-01C: Engine 6.0L Diesel 2006 F-Super Duty 250-550 Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/03/2006
More information2004 F-150 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 5.4L (3V) 2004 F-150 Workshop Manual REMOVAL Procedure revision date: 02/10/2004 Engine Printable View (943 KB) Special Tool(s) Modular Engine Lift Bracket 303-F047
More informationPage 1 of 21 303-01C Engine 5.4L (3V) 2009 F-150 REMOVAL Procedure revision date: 03/26/2009 Cylinder Head Special Tool(s) 3 Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039 Holding
More informationCOMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
More information1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 07/25/2008 Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Lifting Bracket, Engine
More informationARTICLE BEGINNING INTRODUCTION IGNITION SYSTEM CAMSHAFT POSITION (CMP) SENSOR DISTRIBUTOR
Article Text Thursday, August 19, 1999 11:40PM ARTICLE BEGINNING 1996 ENGINE PERFORMANCE Volkswagen Removal, Overhaul & Installation - Gasoline Cabrio, Golf III, GTI, Jetta III, Passat CAUTION: When battery
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP
More information2003 F-Super Duty /Excursion Workshop Manual
Page 1 of 7 SECTION 303-04F: Fuel Charging and Controls Turbocharger, 6.0L Diesel 2003 F-Super Duty 250-550/Excursion Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Turbocharger
More information2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)
1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15
More informationSECTION C Engine 5.4L (3V)
303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Engine Front Cover... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Engine Front
More information1988 Ford F-350 PICKUP
1988 Ford F-350 PICKUP Submodel: Engine Type: V8 Liters: 7.5 Fuel Delivery: FI Fuel: GAS 1987 93 4.9L Engine The intake and exhaust manifolds on these engines are known as combination manifolds and are
More informationSECTION D Fuel Charging and Controls Turbocharger
303-04D-i Fuel Charging and Controls Turbocharger 303-04D-i SECTION 303-04D Fuel Charging and Controls Turbocharger CONTENTS PAGE Turbocharger Body On... 303-04D-2 303-04D-2 Fuel Charging and Controls
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More informationSection 7.3 Water Manifold has been updated.
NUMBER: 08 DD15-11 S.M. REF.: 7.3 ENGINE: DD15 DATE: September 2008 SUBJECT: WATER MANIFOLD PUBLICATION: DDC-SVC-MAN-0002 Section 7.3 Water Manifold has been updated. 7.3 WATER MANIFOLD Coolant flows from
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Valve Cover» Service and Repair» Procedures» LH Valve Cover LH Removal 1. Disconnect the battery ground cable. 2. Remove the air cleaner
More informationDisconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
More informationLSX Intake Manifold. #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body)
LSX Intake Manifold #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body) Thank you for your purchase of the most innovative and powerful Gen III (LS1 and LS6) manifold ever developed. We are
More informationON-VEHICLE INSPECTION
452 DLC3 CAN VIM Intelligent Tester G035612E02 ON-VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Listen to the throttle control motor operating sounds. (1) Turn the ignition switch to ON. (2) When pressing
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More information2008 F-Super Duty Workshop Manual
Page 1 of 13 SECTION 303-04C: Fuel Charging and Controls 6.4L Diesel 2008 F-Super Duty 250-550 Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/04/2009 Fuel Injection Pump High Pressure,
More information2006 Expedition/Navigator Workshop Manual
7. Remove the RH variable camshaft timing (VCT) oil control solenoid. For additional information, refer to Section 303-14. 8. Remove the RH ignition coils. For additional information, refer to Section
More informationCylinder head, removing and
Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder
More informationREMOVAL AND INSTALLATION OF TRANSAXLE (4WD)
MT63 REMOVAL AND INSTALLATION OF TRANSAXLE (4WD) REMOVAL AND INSTALLATION OF TRANSAXLE REMOVE AND INSTALL TRANSAXLE AS SHOWN MT64 REMOVAL OF TRANSAXLE 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More information(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel TYPE TIGHTENING TORQUES. Rev. 2.0 OE
(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel 1 TYPE TIGHTENING TORQUES 1. Cylinder head CAUTION : (*) Follow the tightening sequence. Reference Designation (1) bolts - Throttle butterfly housing Tightening
More informationENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
More information2007 Volkswagen Touareg (7LA) V6-3.6L (BHK)
Page 1 of 11 2007 Volkswagen Touareg (7LA) V6-3.6L (BHK) Vehicle» Engine, Cooling and Exhaust» Engine» Intake Manifold» Service and Repair» Intake Manifold Intake Manifold Special tools, testers and auxiliary
More informationCylinder Heads Remove and Install (all) ( ) Remove. 2,5l TCI Diesel Engine. Special Tools Bolt tightening angle gauge
Cylinder Heads Remove and Install (all) ( 64 0) Special Tools 00 00 00 Splined head socket, cylinder head bolts 00 Cylinder head locating studs 540 04 540 Bolt tightening angle gauge 04 Wrench for injectors
More information2002 Escape Workshop Manual
SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft
More informationINTAKE AND EXHAUST 15-1 CONTENTS SERVICE ADJUSTMENT PROCEDURES... 2 EXHAUST MANIFOLD EXHAUST PIPE AND MAIN MUFFLER...
I i 15-1 INTAKE AND EXHAUST CONTENTS 110003071 L AIR CLEANER 4.5L Engine>....3 AIR CLEANER 4.8L Engine>....4 EXHAUST MANIFOLD... 10 EXHAUST PIPE AND MAIN MUFFLER... 13 GENERAL INFORMATION.... 2 INTAKE
More informationIG 1 2GR-FE IGNITION IGNITION SYSTEM IGNITION SYSTEM ECM ENGINE ROOM R/B - IG2 FUSE - ST/AM FUSE IGNITION COIL NOISE FILTER NOISE FILTER A137458E01
NITION SYSTEM ENGINE 2GR-FE PARTS LOCATION 2GR-FE NITION NITION SYSTEM 1 ECM ENGINE ROOM R/B - 2 FUSE NITION COIL - ST/AM FUSE NOISE FILTER NOISE FILTER A137458E01 2 2GR-FE NITION NITION SYSTEM SYSTEM
More informationPage 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.
More informationCylinder Head Removal
2006 Odyssey Cylinder Head Removal Report a problem with this article NOTE: Use fender covers to avoid damaging painted surfaces. To avoid damaging the wires and terminals, unplug the wiring connectors
More informationEXHAUST SYSTEM AND INTAKE MANIFOLD
J EXHAUST SYSTEM AND INTAKE MANIFOLD 11-1 EXHAUST SYSTEM AND INTAKE MANIFOLD CONTENTS page EXHAUST SYSTEM... 1 EXHAUST SYSTEM DIAGNOSIS... 2 page SERVICE PROCEDURES... 3 TORQUE SPECIFICATIONS... 10 EXHAUST
More informationTiming Drive Components Camshaft Timing
SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner
More informationFord 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
More informationFuel System of Service Manual
Fuel System of Service Manual for H Series Engine for Generator sets October of 2015 1 Table of Contents 13.1 About System... 13-3 13.2 System Diagram... 13-4 13.2.1 Fuel system (4 cylinders)... 13-4 13.2.2
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationEGR heater plate removal and installation procedure has been added.
NUMBER: 08 60-3 S.M. REF.: 8.3 ENGINE: EPA07 Series 60 DATE:June 2008 SUBJECT: EGR HEATER PLATE PUBLICATION: DDC-SVC-MAN-0005 EGR heater plate removal and installation procedure has been added. 8.3.1 REMOVAL
More informationEXHAUST GAS RECIRCULATION (EGR) SYSTEM (4A FE)
ENGINE EG121 EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4AFE) EGR SYSTEM INSPECTION 1. INSPECT AND CLEAN FILTER IN EGR VACUUM MODULATOR (a) Remove the cap and filter. (b) Check the filter for contamination
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More information2. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement.
VALVE COVER GASKET Valve Rocker Arm Cover Replacement - Left Side Removal Procedure 1. Partially drain the cooling system. Refer to Cooling System Draining and Filling (LZE, LZ4, LZG, 9C1, 9C3, GE47716
More informationFor Troubleshooting of DTC related components, see chart on page INTAKE AIR BYPASS (IAB) HIGH CONTROL SOLENOID
Index For Troubleshooting of DTC related components, see chart on page 11-53. '96-99 models: EXHAUST GAS RECIRCULATION (EGR) and LIFT MANIFOLD ABSOLUTE PRESSURE (MAP) INTAKE AIR BYPASS (IAB) HIGH page
More information