JFEBEAR RUNNING MANUAL

Size: px
Start display at page:

Download "JFEBEAR RUNNING MANUAL"

Transcription

1 JFEBEAR-TP-M-001 (REV.2) JFEBEAR RUNNING MANUAL JANUARY 2007 JFE STEEL CORPORATION Legal Notice The use of the information is at the reader's risk and no warranty is implied or expressed by JFE Steel Corporation with respect to the use of information contained herein. The information in this publication is subject to change or modification without notice. Please contact the JFE Steel office for the latest information. *JFEBEAR is a registered trademark in Japan.

2 CONTENTS PREFACE PREPARATIONS BEFORE RUNNING Handle Pipes Carefully Racking Pipe Segregate Unusable Pipe Clean and Inspect Connections Make-up Loss THREAD PROTECTORS Always Protect Threads and Seals Protector Selection RUNNING Check Torque Value Place Pipe on Racks Handling Pipes Coupling Threads and Seals Make-up Acceptance and Rejection Lowering Tubing String BREAK-OUT AND LAYDOWN PROCEDURES Pulling of Pipe Rotation of Connection RE-RUNNING JFEBEAR CONNECTIONS HIGH CHROME STEEL TUBULAR STORAGE RECOMMENDATIONS Remove Tubular Goods Inspect Tubular Periodically For Long Storage Out Door Storage Warning Plate Storage Following Pulling HIGH CHROME STEEL SPECIAL HANDLING PRECAUTIONS HIGH CHROME STEEL RUNNING PROCEDURES Running of High chrome steel JFEBEAR Connections HIGH CHROME STEEL RE-RUNNING SPECIAL RECOMMENDATION FOR SOUR SERVICE (H 2 S) Hard Spots Avoid Damage... 8 Definition of 'HIGH CHROME STEEL': steel containing 9% or more chromium. JFEBEAR Example make-up graphs... 9

3 JFEBEAR-TP-M-001 (REV.2) Page-1 PREFACE The JFEBEAR connection has been developed and patented by JFE STEEL CORPORATION. Connections are manufactured by JFE STEEL CORPORATION or its authorized MANUFACTURING LICENSEES. The recommendations and illustrations in this document were developed from the offshore and onshore experience of running crews and advice received from Operators and their contractors. Please be aware of the useful guidelines and recommendations in this document and apply them when necessary. 1 PREPARATIONS BEFORE RUNNING 1.1 Handle Pipes Carefully Use pipe body slings in preference to end hooks. End hooks are only permissible with the correct type of thread protector. 1.2 Racking Pipe Rack pipe in level horizontal layers, at least 8" (200mm) above the ground surface. Separate layers of pipe with at least three wooden slats placed perpendicular to pipe at each end and in the middle. Slats should at least be 4" x 2" (100mm x 50mm). Do not stack pipe more than 7' (2.1meters) high. Take care not to crush bottom layers of pipe and ENSURE RACK IS SAFELY SECURED. 1.3 Segregate Unusable Pipe Remove rust, scale, dirt and debris from inside and outside surfaces. Remove any dented, bent or otherwise damaged pipe for possible repair. 1.4 Clean and Inspect Connections Remove all lubricants or compound with liquid solvents (not diesel fuel) Use non-metallic brushes to remove adhered solids. Segregate all rejected thread/seals/tubes. Minor damage on pin & box connection may be repaired in accordance with JFEBEAR-TP-M-101, prior to running. THOROUGHLY DRY THREADS AND SEAL SURFACES. If pipe is to be moved from rig site back into storage then re-apply an acceptable thread compound thinly and evenly on all thread and seal surfaces. Use a clean uncontaminated compound and apply with a clean non-metallic brush. Avoid excessive amounts of thread compound. For long term storage, use a suitable storage compound such as Kendex for both pins and boxes.

4 JFEBEAR-TP-M-001 (REV.2) Page-2 Note: API thread compounds may not be suitable due to "drying out" and reduced corrosion resistance. Replace CLEAN AND DRY pin thread protectors. Note: Application of thread or storage-compound to connection seals and thread surfaces is recommended if there are any significant delays in pipe running. Clean and dry thread protectors should also be re-fitted. 1.5 Make-up Loss The effective length of each tube is the overall length minus the make-up loss. The make-up loss is the pin length listed in the Table 1. Table 1 Make-up Loss Length Outside Diameter Make-up Loss Length inch mm inch mm

5 JFEBEAR-TP-M-001 (REV.2) Page-3 2 THREAD PROTECTORS 2.1 Always Protect Threads and Seals Ensure approved thread protectors are installed at the mill and at the storage point. Use only clean and undamaged protectors. Use only clean non-contaminated thread or storage compound applied thinly and evenly over entire thread/seal area. Assemble protector to hand tight position. Insert suitable torque bar in the grooves provided and tighten. Note: Do not hammer bar or protector to tighten. 2.2 Protector Selection (Refer to JFEBEAR-TP-N-101) Approved protectors may be of metal or molded plastic construction. Premium connections require adequate protection in the threaded area, particularly at the extremity of the pin seal. A minimum of 3/4" (19mm) is recommended between the bottom of the torque bar groove and the position of the pin seal extremity when the protector is fully tightened. Protectors should be manufactured to allow an even thickness of thread compound to cover threads and seal when in the fully made-up position. Protectors should be manufactured for optimum performance in a temperature range of -40 F to +110 F (-40 C to +45 C). 3 RUNNING 3.1 Check Torque Values ALWAYS check with Manufacturer s Authorized Representative to determine the latest recommended make-up torque values for the JFEBEAR connection. Note: Recommended maximum calibration interval for all Make up equipment should be no more than 6 months. 3.2 Place Pipe on Racks (see also section 1.1 and 1.2) Segregate pipe that has been damaged or pipe which is not fit for purpose. Unless previously done, clean and inspect all connections per guidelines stated in section 1.4. When ready to commence running, ensure clean and dry pin thread protectors are in place to protect threads and seals while pipe is being lifted through V door. 3.3 Handling Pipes Handle pipes as described in section 1.1. Use only clean and undamaged handling plugs. Make-up hand tight only. Do not use a cheater bar. With collar or slip type elevators, ensure that elevator diameters are compatible with coupling and pipe body diameters.

6 JFEBEAR-TP-M-001 (REV.2) Page-4 If drifting is required, carefully remove closed end thread protector, replace with a clean open end thread protector and drift tube with non-metallic Teflon/Nylon type "rabbit" of correct drift diameter. (Metal drifts are not recommended unless the ends are tapered sufficiently to avoid torque shoulder contact.) Lift pipe to vertical pre-stab position above the rotary table. Remove pin thread protector and apply clean uncontaminated approved thread compound with friction factor of 1.0. Use nonmetallic brush. If compound friction factor is not equal to 1.0, as is often the case with the environmentally friendly compounds, refer to Manufacturer s Authorized Representative for revised torque figures. Note: Hold pipe away from open coupling to avoid debris contamination of open box. 3.4 Coupling Threads and Seals Ensure Coupling thread and seal areas are covered with a light coat of recommended thread compound. Prior to stabbing, fit a clean properly sized STABBING GUIDE over the coupling and securely fasten. Align the pipe and carefully lower pin through the stabbing guide into the coupling. Rotate tube BY HAND OR WITH STRAP WRENCH until threads are fully engaged to the hand tight position. With power tongs rotate tube until seal engagement and desired final torque is achieved. Final make-up torque should not exceed 6 RPM. (COMPUTER CONTROLLED MAKE-UP TORQUE TURN EQUIPMENT IS RECOMMENDED) 3.5 Make-up Acceptance and Rejection For an acceptable make-up both the total torque and shoulder torque requirements must be satisfied following guideline. Final torque shall be meet between specified minimum torque and maximum torque. Shoulder torque shall not be exceeded specified maximum shoulder torque. Connections which do not meet the make-up requirements should be broken out and should be inspected in accordance with JFEBEAR- TP-M-101 prior to re-makeup. 3.6 Lowering Tubing String Lower entire tubing string by one joint and proceed to next connection. For subsequent connections follow make-up procedures 3.1 through 3.5.

7 JFEBEAR-TP-M-001 (REV.2) Page-5 4. BREAK-OUT AND LAY DOWN PROCEDURES 4.1 Pulling of Pipe Pulling of pipe should be conducted with care to avoid damage to threads and seal areas. Ensure that proper alignment of blocks over the well is achieved and that derrick-man is aligning each joint over the well during breakout. Misalignment may result in connection thread galling. Take care not to over rotate during back-out so pin connection does not "drop" back into coupling. Apply tension to the joint (or stand) being backed out. The applied load should approximately equal the weight of the joint. Use a weight compensator where possible. During stabbing, use a stabbing guide to avoid pin threads or seals striking the coupling. Re-apply both pin and coupling thread protectors immediately after pin/coupling disengagement. Pulling in singles is recommended. If "stood back" in the derrick, ensure the pin end protectors are fitted and "stand" is seated on a wooden or similar non-metallic surface. 4.2 Rotation of Connection Place power tong on the top joint with the back-up tong on lower half of coupling to avoid unnecessary gripping pressure on the connection end to be broken-out. Set tong rotation for break-out and ensure single joint or stand weight is taken up by elevators. Break-out the connection with power tongs, approximately 1 turn for tubing and 2 turns for casing. After breakout, remove power tongs and rotate connection out by hand or strap wrench. Place an appropriately sized STABBING GUIDE over the coupling and lift top joint (stand) clear of coupling and stabbing guide. Install a CLEAN pin protector and either lay the joint down or stand into derrick on a clean non-metallic surface. If laying down pipe onto pipe deck use slats. Install a CLEAN coupling protector into the coupling. Lift string to next breakout joint and repeat steps as per section RE-RUNNING JFEBEAR CONNECTIONS Instructions for re-running joints are exactly same as for new connections and the same make-up torque values are applied. Prior to re-running each connection should be inspected in accordance with JFEBEAR-TP-M-101.

8 6. HIGH CHROME TUBULAR STORAGE RECOMMENDATIONS JFEBEAR-TP-M-001 (REV.2) Page Removing Tubular Goods Where possible, remove the tubular goods from their export packing IMMEDIATELY upon receipt and store them indoors in a dry atmosphere. 6.2 Inspect Tubulars Periodically Inspect the tubular periodically, i.e., every one to three months depending on atmospheric conditions. Routine inspection should include: O.D. check for discoloring or pitting I.D. check for discoloring or pitting Remove thread protectors and check condition of connections and storage compound. Replace connection storage compound as required. Apply evenly to thread and seal areas. 6.3 For Long Term Storage For periods of storage longer than two months a connection storage compound shall be used. Note: API THREAD COMPOUNDS ARE NOT RECOMMENDED FOR USE AS A LONG TERM STORAGE COMPOUNDS. 6.4 Out Door Storage If out door storage is the only option, the following additional procedures are recommended. Protect from rain and spray with tarpaulins or plastic covering. Sweating / condensation may occur if there is insufficient air circulation. Avoid stagnant water or moisture. Every thirty days, roll tubes to ensure that no moisture remains trapped between stripping and pipe OD. This also allows any trapped moisture to dry. It is recommended to use plastic stripping or zinc paint on wood strips to avoid direct contact between tubulars and wood. Store tubular with one end elevated to allow condensation or other trapped water to drain from tube I.D. 6.5 Warning Plate Refer to the "WARNING PLATE" attached to the export package for additional information. 6.6 Storage Following Pulling (Short Term or Long Term) Special attention must be given to high chrome steel products when removed from well due to the materials pitting susceptibility caused by Chlorides in an oxygen rich environment. Immediately upon removing tubulars from well, they should be flushed with fresh water and stored with one end elevated, to allow condensation or other trapped water to drain from tube I.D.

9 JFEBEAR-TP-M-001 (REV.2) Page-7 After drainage is completed the connections should be cleaned, dried and inspected. If repairs are required it should be performed in conjunction with JFEBEAR-TP-M-101. Repaired connections should be protected using appropriate storage compound. Re-fit clean and dry thread protectors. Note: Above steps are applicable if pipe is to be re-run within very short period of time, such as 12 ~ 72 hours. For longer periods (1 week to 4 weeks), the same applies with the exception that water soluble corrosion inhibitor for Brine Solutions should be sprayed on O.D. & I.D. of pipe after drainage is complete. Note: One such product is named: Aqua-Cure 690 and is supplied by Oil Center Research. For longer term storage greater than 1 month, it is recommended to follow the same process with the exception that external pipe coating, namely clear varnish and internal pipe coating, namely mineral oil should be applied. 7. HIGH CHROME STEEL SPECIAL HANDLING PRECAUTIONS Handle joints one at a time using nylon slings. Avoid joints contacting each other, i.e. "banging together" in order to prevent local surface hardened spots which may lead to corrosion. Ensure pipe racks and pick-up/lay-down equipment is sufficiently padded to help prevent unnecessary contact between joints and other steel components. 8. HIGH CHROME STEEL RUNNING PROCEDURES 8.1 Running of High Chrome Steel JFEBEAR Connections Running of high chrome steel with JFEBEAR connections should be handled with the following extra precautions taken. Single joint compensators are recommended. Low stress dot dies or other non-marking systems in tongs, elevators and slips are the preferred method. Non-directional, fine tooth, low stress dies with 360 contacts are also acceptable. Rotate tube by hand with strap wrench until threads are fully engaged. With power tongs, rotate tube to final torque not exceeding 6 rpm. 9. HIGH CHROME STEEL RE-RUNNING Please refer to Running Instructions provided earlier in this document.

10 JFEBEAR-TP-M-001 (REV.2) Page SPECIAL RECOMMENDATION FOR SOUR SERVICE (H 2 S) 10.1 Hard Spots NEVER use pipe on which hard spots have developed from the use of direct flame heating, welding or impact damage Avoid Damage Avoid damage which may result in residual stress to effected area. For that reason, DO NOT: Cold-straighten even slightly-deformed pipe. Use pipe or couplings showing sharp edged slip or tong marks. Hammer pipe or couplings. Compress or deform pipe in the slips. Use pipe exhibiting excessive out of roundness. Exceed recommended make-up torque. Apply loads in excess of performance capabilities. Permit excessive bending of the string when the load is close to elastic limit of the material. Improvise by using items of different steel strength and quality from those programmed.

11 JFEBEAR Example make-up graphs JFEBEAR-TP-M-001 (REV.2) Page-9 Fig.1 Maximum torque Optimum torque Minimum torque Torque Max. shoulder torque Pick shoulder here Min. shoulder torque Turn Fig.1 is an example of an acceptable make up graph for JFEBEAR connection. Fig.2 Maximum torque Optimum torque Minimum torque Torque Max. shoulder torque Min. shoulder torque Turn Fig.2 is an example of shoulder torque that is too high. Possible causes: Friction factor of dope is too high. Dope is contaminated. Pipe is not straight. Pin or box stand-off is outside tolerance range. Fix: Break out, clean and inspect the connection, if no galling is observed remake up.

12 JFEBEAR-TP-M-001 (REV.2) Page-10 Fig.3 Maximum torque Optimum torque Minimum torque Torque Max. shoulder torque Turn Fig.3 is an example of shoulder torque that is too high. Causes: Friction factor of dope is too high. Dope is contaminated. Pipe is not straight. Pin or box stand-off is outside tolerance range. Min. shoulder torque Fix: Break out, clean and inspect the connection, if no galling is observed re-make up. Fig.4 Maximum torque Optimum torque Minimum torque Torque Max. shoulder torque Turn Fig.4 is an example graph of what could be yielding or slipping. Break out, clean and inspect the connection. If yielding has occurred reject Pin and Box connection. Calibrate or change load cell, re-check system set up. If yielding has not occurred, inspect for slipping. Min. shoulder torque

13 JFEBEAR-TP-M-001 (REV.2) Page-11 Fig.5 Maximum torque Optimum torque Minimum torque Torque Max. shoulder torque Min. shoulder torque Turn Fig.5 is an example of slipping make up. Break out, clean and inspect the connection. Re-make up. Correct problem of slipping.

JFETIGER RUNNING MANUAL. Downloaded From JFETC.COM Thu, 20 Sep :15: JFETIGER. * valid at time of download * JANUARY 2015

JFETIGER RUNNING MANUAL. Downloaded From JFETC.COM Thu, 20 Sep :15: JFETIGER. * valid at time of download * JANUARY 2015 JFETIGER-TP-M-001 (REV.3) JFETIGER RUNNING MANUAL JFETIGER JANUARY 2015 JFE STEEL CORPORATION CONTENTS JFETIGER... 1 PREFACE...1 1 PREPARATIONS BEFORE RUNNING...1 1.1 Handle Pipes Carefully...1 1.2 Racking

More information

RECOMMENDED PRACTICE TKC FJ-150

RECOMMENDED PRACTICE TKC FJ-150 1.0 SCOPE 1.1 This document sets forth Hunting s recommended practice for the field running and handling procedures that should be used in conjunction with all Hunting tubing and casing product line connections.

More information

RECOMMENDED PRACTICE SEAL-LOCK FLUSH/SEMI FLUSH CONNECTIONS

RECOMMENDED PRACTICE SEAL-LOCK FLUSH/SEMI FLUSH CONNECTIONS 1.0 SCOPE 1.1 This document sets forth Hunting s recommended practice for the field running and handling procedures that should be used in conjunction with SEAL LOCK tubing and casing product line connections.

More information

Benoit Premium Threading, LLC Recommended Practice. Approved By: Benoit Quality Assurance Department Date: January 6, 2017

Benoit Premium Threading, LLC Recommended Practice. Approved By: Benoit Quality Assurance Department Date: January 6, 2017 1 of 12 SCOPE The following outlines the recommended practices for field handling, running, and pulling of tubular products with Benoit Flush & and is intended to assist the user in the proper installation

More information

OCTG Mill RUNNING AND PULLING PROCEDURE FOR TPS-MULTISEAL (ALL TYPES & GRADES) QP 05-16E Revision No. 7 Page 1 of 11

OCTG Mill RUNNING AND PULLING PROCEDURE FOR TPS-MULTISEAL (ALL TYPES & GRADES) QP 05-16E Revision No. 7 Page 1 of 11 QP 05-16E Revision No. 7 Page 1 of 11 General 1. Take care against damage (dropping, hit e. g.). 2. Use enough non-metal-timbers for storage under each layer of bundles/tubes. 3. Never place the timbers

More information

Benoit Premium Threading, LLC Recommended Practice. Approved By: Benoit Quality Assurance Department Date: May 1, 2013

Benoit Premium Threading, LLC Recommended Practice. Approved By: Benoit Quality Assurance Department Date: May 1, 2013 1 of 11 SCOPE The following outlines the recommended practices for field handling, running, and pulling of tubular products with Benoit BTS Premium Connections and is intended to assist the user with correct

More information

RECOMMENDED PRACTICE TKC-4040 V.I.T. and HO-I

RECOMMENDED PRACTICE TKC-4040 V.I.T. and HO-I 1.0 SCOPE 1.1 This document sets forth Hunting's recommended practice for the field running and handling procedures that should be used in conjunction with the product line. 2.0 REFERENCES 2.1 The following

More information

RECOMMENDED PRACTICE SEAL-LOCK HT

RECOMMENDED PRACTICE SEAL-LOCK HT 1.0 SCOPE 1.1 This document sets forth Hunting's recommended practice for the field running and handling procedures that should be used in conjunction with the product line. 2.0 REFERENCES 2.1 The following

More information

Running Procedure. VAxplorer. Rev.:1.

Running Procedure. VAxplorer. Rev.:1. Running Procedure VAxplorer Rev.:1 www.voestalpine.com/tubulars VAxplorer RS-RP-VAX-1 Rev.1: Change of layout (new corporate design) www.voestalpine.com/tubulars Table of Content Table of Content Proprietary

More information

Running Procedure. Rev.:2 VAGT.

Running Procedure. Rev.:2 VAGT. Running Procedure VAGT Rev.:2 www.voestalpine.com/tubulars VAGT RS-RP-VAGT-1 Rev.2: Change on page 15 (note to field repair table) www.voestalpine.com/tubulars Table of Content Table of Content Proprietary

More information

Running Procedure. VAsuperior. Rev.:2.

Running Procedure. VAsuperior. Rev.:2. Running Procedure VAsuperior Rev.:2 www.voestalpine.com/tubulars VAsuperior RS-RP-VAS-1 Rev.2 : Changes on page 9 and 10 (min. torque on shoulder requirement for Casing from 50% to 30%); Change on page

More information

Running Procedure. VAroughneck. voestalpine Tubulars GmbH & Co KG Rev.: 0

Running Procedure. VAroughneck. voestalpine Tubulars GmbH & Co KG  Rev.: 0 Running Procedure VAroughneck Rev.: 0 www.voestalpine.com/tubulars Table of Content Proprietary connections Proprietary grades VAroughneck Technical data sheet Running and handling Visual inspection and

More information

Drill Pipe Connection Care and Handling

Drill Pipe Connection Care and Handling Drill Pipe Connection Care and Handling www.commandenergy.com TABLE OF CONTENTS Introduction to double shoulder connections Picking up new pipe Thread Compound Application (Doping) Making up connections

More information

Wedge TenarisHydril Running Manual.. Premium connection approved thread compounds TSH-MD

Wedge TenarisHydril Running Manual.. Premium connection approved thread compounds TSH-MD IDM Code GDL00376/3 / March 2018 TenarisHydril Wedge 623 Connection Scope These guidelines apply specifically to the use of TenarisHydril Wedge 623 connections. This document should be used in conjunction

More information

SEAL-LOCK APEX ANCILLARY

SEAL-LOCK APEX ANCILLARY 1.0 SCOPE 1.1 This document sets forth the procedure for the mill end make-up or bucking of SEAL-LOCK APEX casing connectors. 2.0 DEFINITION 2.1 Make-up shall be defined as the power tight application

More information

Wedge 533 / 503 / 553

Wedge 533 / 503 / 553 Wedge 533 / 503 / 553 Connections Scope These guidelines apply specifically to the use of Wedge 533, Wedge 503 and Wedge 553 connections. This document should be used in conjunction with the Running Manual,

More information

. Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Equipment, Material & Documents

. Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Equipment, Material & Documents IDM Code GDL23370/1 / March 2018 TenarisHydril MACII Connection Scope These guidelines apply specifically to the use of TenarisHydril MACII connections. This document should be used in conjunction with

More information

U. S. STEEL TUBULAR PRODUCTS PROPRIETARY THREAD CONNECTION MANUAL

U. S. STEEL TUBULAR PRODUCTS PROPRIETARY THREAD CONNECTION MANUAL Page: 1 of 13 1.0 Scope. 1.1 he purpose of this specification is to provide the procedure to aid in the successful running and pulling of. S. Steel (SS) SS-CDC, SS- CDC H and SS-CDC H S threaded and coupled

More information

1. Use slip type elevators for flush, near flush, integral, special clearance and special bevel coupled connections.

1. Use slip type elevators for flush, near flush, integral, special clearance and special bevel coupled connections. IDM Code GDL23350/1 / March 2018 Running Equipment / tools 1. Use slip type elevators for flush, near flush, integral, special clearance and special bevel coupled connections. 2. Do not set elevators on

More information

U. S. STEEL TUBULAR PRODUCTS PROPRIETARY THREAD CONNECTION MANUAL

U. S. STEEL TUBULAR PRODUCTS PROPRIETARY THREAD CONNECTION MANUAL Page: 1 of 13 1.0 Scope. 1.1 his engineering specification describes the requirements for running and pulling of. S. Steel (SS) premium and semi-premium internally shouldered threaded and coupled connections.

More information

TKC CONVERTIBLE: 8 RD / NUE / EUE / BUTTRESS 4040 / 4040 HO / 4040 HO-B FS-150 ANCILLARY SPECIFICATION

TKC CONVERTIBLE: 8 RD / NUE / EUE / BUTTRESS 4040 / 4040 HO / 4040 HO-B FS-150 ANCILLARY SPECIFICATION 1.0 SCOPE 1.1 This document sets forth the specification for the mill end make-up or bucking of Hunting's TKC Convertible connectors. 2.0 DEFINITION 2.1 Make-up shall be defined as the power tight application

More information

. Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Equipment, Material & Documents

. Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Equipment, Material & Documents IDM Code GDL00336/2 / March 2018 TenarisHydril Wedge 625 Connection Scope These guidelines apply specifically to the use of TenarisHydril Wedge 625 connections. This document should be used in conjunction

More information

SEAL-LOCK HT-S (TIMED) ANCILLARY SPECIFICATION

SEAL-LOCK HT-S (TIMED) ANCILLARY SPECIFICATION 1.0 SCOPE 1.1 This document sets forth the specification for the mill end make-up or bucking of SEAL-LOCK HT-S connectors. 2.0 DEFINITION 2.1 Make-up shall be defined as the power tight application of

More information

SEAL-LOCK HT ANCILLARY SPECIFICATION

SEAL-LOCK HT ANCILLARY SPECIFICATION 1.0 SCOPE 1.1 This document sets forth the specification for the mill end make-up or bucking of SEAL-LOCK HT connectors. 2.0 DEFINITION 2.1 Make-up shall be defined as the power tight application of a

More information

DRILL PIPE CARE AND HANDLING Complete Group AVENUE Leduc AB T9E 0W1 +1 (780) CG.ENG.

DRILL PIPE CARE AND HANDLING Complete Group AVENUE Leduc AB T9E 0W1 +1 (780) CG.ENG. DRILL PIPE CARE DRILL PIPE INTRODUCTION Box End Hardbanding Tapered Shoulder Tong Area Weld DEFINITION The drillpipe connects the rig surface equipment with the bottomhole assembly and the bit, both to

More information

Initial Running Guidelines

Initial Running Guidelines IDM Code GDL23361/0 / November 2016 16. Running, Pulling and Racking Pipe in Stands In order to ensure performance continuity of the Tenaris product and connections whilst being racked, run and pulled

More information

22. TenarisHydril Blue Thermal Liner Connection

22. TenarisHydril Blue Thermal Liner Connection IDM Code GDL23367/0 / November 2016 22. TenarisHydril Blue Thermal Liner Connection Scope These guidelines apply specifically to the use of TenarisHydril Blue Thermal Liner connections. This document should

More information

Blue Quick Seal Connection

Blue Quick Seal Connection IDM Code GDL00370/3 / March 2018 TenarisHydril Blue Quick Seal Connection Scope These guidelines apply specifically to the use of TenarisHydril Blue Quick Seal connections. This document should be used

More information

SEC Connection. . Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Equipment, Material & Documents

SEC Connection. . Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Equipment, Material & Documents IDM Code GDL23377/1 / March 2018 SEC Connection Scope These guidelines apply specifically to the use of SEC connections. This document should be used in conjunction with the TenarisHydril Running Manual,

More information

MS & MS XT/XC Connections

MS & MS XT/XC Connections MS & MS XT/XC Connections Scope These guidelines apply specifically to the use of MS and MS XT/XC connections. This document should be used in conjunction with the Running Manual, which is the main document

More information

2. The power tong snub line should be attached to a back up post, leveled and positioned at a 90 angle to the power tongs.

2. The power tong snub line should be attached to a back up post, leveled and positioned at a 90 angle to the power tongs. IDM Code GDL23352/1 / March 2018 Torque Application 1. The correct application of torque for the connection type, OD, weight and grade being assembled is imperative in ensuring the connection can perform

More information

3SB Connection. . Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Equipment, Material & Documents

3SB Connection. . Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Equipment, Material & Documents IDM Code GDL23374/1 / March 2018 TenarisHydril 3SB Connection Scope These guidelines apply specifically to the use of TenarisHydril 3SB connections. This document should be used in conjunction with the

More information

Blue Series and Legacy Series Make up Acceptance

Blue Series and Legacy Series Make up Acceptance IDM Code GDL23353/1 / March 2018 Blue Series and Legacy Series Make up Acceptance 1 Computer graph interpretation is exactly as described, interpretation which means it is not an exact science Many things

More information

ER Connection. . Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Equipment, Material & Documents

ER Connection. . Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Equipment, Material & Documents IDM Code GDL23469/1 / March 2018 TenarisHydril ER Connection Scope These guidelines apply specifically to the use of TenarisHydril ER (Easy Running) connections. This document should be used in conjunction

More information

Fishing Bumper Sub. Manual D450

Fishing Bumper Sub. Manual D450 Fishing Bumper Sub Manual D450 Contents Fishing Bumper Sub Overview...2 Use...2 Construction...2 Illustration...3 Operation...4 Fishing Operations...4 Drilling Operations...4 Applying a Downward Blow...4

More information

FIELD INSPECTION OF JFETIGER THREAD. Downloaded From JFETC.COM Fri, 16 Nov :49: * valid at time of download * JFETIGER.

FIELD INSPECTION OF JFETIGER THREAD. Downloaded From JFETC.COM Fri, 16 Nov :49: * valid at time of download * JFETIGER. JFETIGER-TP-M-101 (REV.2) FIELD INSPECTION OF JFETIGER THREAD JFETIGER January 2015 JFE STEEL CORPORATION JFETIGER-TP-M-101 (Rev.2) Page-1 1 SCOPE This section describes the field inspection requirements

More information

Running Procedure for Casing with GB Drilling with Casing Connections

Running Procedure for Casing with GB Drilling with Casing Connections OVERVIEW This field running procedure applies to makeup of (GB DwC) which include GB CD, GB CDE, GB RDB, AND GB RDB WS with GB Butt (Buttress), GB 4P, and GB 3P thread forms. All of these connections are

More information

Contents. RE PS Revision 5

Contents. RE PS Revision 5 Contents Introduction.. 3 1 Scope.... 4 2 Normative references 4 3 Terms and definition.... 4 4 Transportation, handling operations and storage 4.1 Transportation.... 5 5 4.2 Handling operations.. 6 4.3

More information

HUB & WHEEL INSTALLATION

HUB & WHEEL INSTALLATION HUB & WHEEL INSTALLATION 1.0 SCOPE This specification covers the torque requirements for the attachment of all component parts of Spoke Wheels, Rims, Tyres and Hub assemblies. 1.1 Spoke Wheels CAUTION:

More information

Extended Storage May Extended Storage (More than 30 Days) Procedure for Restoring. to Service an Engine that Has Been in Extended Storage

Extended Storage May Extended Storage (More than 30 Days) Procedure for Restoring. to Service an Engine that Has Been in Extended Storage 4 85-12 1 4 85-12 SUBJECT DATE Extended Storage May 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Extended Storage (More than 30 Days) Deleted "No. 1 diesel

More information

Sentinel 250 Fire Hydrant

Sentinel 250 Fire Hydrant Maintenance Instructions manual table of contents PAGE Sentinel 250 Fire Hydrant Inspection and Lubrication 2 Rotating Hydrant to Face Desired Direction 3 Installing Extension Section 3-6 Restoring Service

More information

INSTRUCTION MANUAL. for BUTTERFLY VALVES

INSTRUCTION MANUAL. for BUTTERFLY VALVES STD-BFV-MGA Revision 0 11/21/03 INSTRUCTION MANUAL for BUTTERFLY VALVES Flowserve U.S. Inc Flow Control Division 1900 South Saunders Street P.O. Box 1961 Raleigh, NC 27603 Phone: (919) 832-0525 FAX: (919)

More information

7. Protection System Testing

7. Protection System Testing MANUAL FOR INSTALLATION AND MONITORING OF UNDERGROUND STORAGE TANKS WITH FACTORY INSTALLED ANODES 1. SCOPE Manufactured by: Granby Industries 1020 André-Liné Granby, Québec, Canada, J2J 1J9. Telephone:

More information

Bray/ VAAS Slurry Series Knife Gate Valve 760/762/765/766/767/768 Series Operation and Maintenance Manual

Bray/ VAAS Slurry Series Knife Gate Valve 760/762/765/766/767/768 Series Operation and Maintenance Manual Bray/ VAAS Knife Gate Valve 760/762/765/766/767/768 Series Table of Contents Definition of Terms 1 Safety Instructions 1 Introduction 2 Unpacking 2 Storage 2 Installation 3 Commissioning 3 Cylinder-Operated

More information

Casing & Tubing Running Services

Casing & Tubing Running Services Tubular About Us: SAKNAFTA Tubular Services Are Committed to deliver the safest and most efficient services to our client with advanced, comprehensive tubular solutions backed by a group of experts. SAKNAFTA

More information

SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS

SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS 82-L0352 REV 8 4-27-2011 WARNING! HYDRAULIC COMPONENTS CAN CAUSE SERIOUS INJURY OR DEATH IF PROPER SAFETY PRECAUTIONS ARE

More information

Сontents. RE PS Revision 5

Сontents. RE PS Revision 5 Сontents Introduction... 3 1 Scope... 4 2 Normative references.. 4 3 Terms and definitions.. 4 4 Transportation, handling operations and storage 5 4.1 Transportation... 5 4.2 Handling operations.. 6 4.3

More information

Lincoln Hoist. Web Hoist Operating Manual. Lincoln Hoist

Lincoln Hoist. Web Hoist Operating Manual. Lincoln Hoist Lincoln Hoist Web Hoist Operating Manual Lincoln Hoist Mfg. by Lincoln Precision Machining Company 121 Creeper Hill Road, P.O. Box 458, North Grafton, MA 01536 USA Toll Free (888) 306-7222 Phone (774)

More information

READ AND SAVE THESE INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Part #469003 Model Vektor -H Installation Operation and Maintenance Manual for Vektor-H Laboratory Exhaust System Receiving Greenheck model Vektor-H fans are thoroughly

More information

MUELLER. Super Centurion 350 Fire Hydrant. Reliable Connections. Inspection and Maintenance 2. Filling Oil Reservoir 3. Facing the Hydrant 4

MUELLER. Super Centurion 350 Fire Hydrant. Reliable Connections. Inspection and Maintenance 2. Filling Oil Reservoir 3. Facing the Hydrant 4 operating Instructions manual MUELLER Super Centurion 350 Fire Hydrant table of contents PAGE Inspection and Maintenance 2 Filling Oil Reservoir 3 Facing the Hydrant 4 Restoring Service after Traffic Knockover

More information

back to main page Type: Butterfly valves Instructions and Operation Manual Warning! Warning! Danger for life! 1. Intended use Danger for life!

back to main page Type: Butterfly valves Instructions and Operation Manual Warning! Warning! Danger for life! 1. Intended use Danger for life! Instructions and operation manual for butterfly valves This manual is intended to support the users of Herberholz butterfly valves type HRD/HRA, RD/RA, LDKE/LDKF for installation, operation and maintenance

More information

Keystone Butterfly valves ParaSeal Installation and maintenance instructions

Keystone Butterfly valves ParaSeal Installation and maintenance instructions Before installation these instructions must be fully read and understood Please read these instructions carefully Hazard potentials: disregarding of instructions improper use of product insufficiently

More information

High Capacity Industrial Universal Joints Installation and Maintenance Manual

High Capacity Industrial Universal Joints Installation and Maintenance Manual High Capacity Industrial Universal Joints Installation and Maintenance Manual Form No. 376-SH, 6/97 U - Joint Installation and Maintenance Manual TABLE OF CONTENTS SECTION TITLE PAGE 1 General...: 4 2

More information

Fluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL

Fluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL Fluid-O-Tech PUMP TECHNOLOGY AT ITS BEST WWW.FLUID-O-TECH.COM Office: 161 Atwater St., Plantsville, CT 06479 Phone: (860) 276-9270 Fax: (860) 620-0193 ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL 08/09 Ed.,

More information

CONTROL VALVES SINGLE PORTED CLASSES DL, DDL, DOS, DDOS

CONTROL VALVES SINGLE PORTED CLASSES DL, DDL, DOS, DDOS 12501 Telecom Drive, Tampa Florida 33637 Installation, Operation and Maintenance 10/1.5.1 Rev. 0 CONTROL VALVES SINGLE PORTED CLASSES DL, DDL, DOS, DDOS TABLE OF CONTENTS INSTALLATION...2 VALVE POSITION...2

More information

Fluid Coil Installation, Operation and Maintenance

Fluid Coil Installation, Operation and Maintenance Bulletin FCO&I 001 REV A Fluid Coil Installation, Operation and Maintenance Monika Hewlett Packard Company [Pick the date] FLUID COIL INSTALLATION, OPERATION & MAINTENANCE GUIDELINES Fluid Coil Installation,

More information

Handling / Lift Plugs

Handling / Lift Plugs IDM Code GDL23351/1 / March 2018 Handling / Lift Plugs 1. Handling plugs are essential in order to run flush and near flush type connections. 2. Handling Plugs and Lifting Plugs are tubular accessories

More information

DRILLING MOTOR HANDBOOK

DRILLING MOTOR HANDBOOK DRILLING MOTOR HANDBOOK GORILLA Drilling Motors TM rev213.6.19 DRILLING MOTOR HANDBOOK www.axonep.com The information contained in this handbook is for reference only. AXON Downhole Products Inc. does

More information

CUSTOMER S MANUAL. Coil models FV,FK,FH,FC,FD,FP,FS TV,TK,TC,TD

CUSTOMER S MANUAL. Coil models FV,FK,FH,FC,FD,FP,FS TV,TK,TC,TD CUSTOMER S MANUAL Coil models FV,FK,FH,FC,FD,FP,FS TV,TK,TC,TD 1 Version: 8. Jui 2016 INDEX SIDE RECEPTION MANUAL...... 3 On Receipt of shipment... 3 ASSEMBLING MANUAL... 4 USER S MANUAL... 7 Startup..

More information

Operating Procedures for 2 SCH 160 through 10 SCH 120 GripTight Long Radius Elbow Test Plug

Operating Procedures for 2 SCH 160 through 10 SCH 120 GripTight Long Radius Elbow Test Plug EST Group DC2545 10/15 Rev1 01/17 Page 1 of 11 Operating Procedures for 2 SCH 160 through 10 SCH 120 GripTight Long Radius Elbow Test Plug Thank you for choosing to use a GripTight Long Radius Elbow Test

More information

MODCO TM FIGURE 500 CLOSURE

MODCO TM FIGURE 500 CLOSURE CLOSURE SPECIALISTS SINCE 1981 MODCO TM FIGURE 500 CLOSURE INSTALLATION INSTRUCTIONS (!) THE INFORMATION PROVIDED IN THIS DOCUMENT IS VERY IMPORTANT (!) & (!) needs to be shared with everyone involved

More information

OIL COUNTRYTUBULAR GOODS

OIL COUNTRYTUBULAR GOODS x 5.21 R3 GRADE PS80 73 x 5.51 R2 114.3 NUE OIL COUNTRYTUBULAR GOODS PRUDENTIAL STEEL E PS80 098 08908076 3.12 3513813 567 EUE 60.3 x 4.83 R2 GRADE H40 73 x 5.51 R2 ST + C NUE 73.0 x 5.5 R2 HFIW RELIABLEPRODUCT

More information

I-VIC300MS. Series 761 Vic-300 MasterSeal Carbon Steel Butterfly Valve Series 461 Vic-300 MasterSeal Stainless Steel Butterfly Valve WARNING

I-VIC300MS. Series 761 Vic-300 MasterSeal Carbon Steel Butterfly Valve Series 461 Vic-300 MasterSeal Stainless Steel Butterfly Valve WARNING INSTALLATION AND MAINTENANCE INSTRUCTIONS I-VIC300MS Series 761 Vic-300 MasterSeal Carbon Steel Butterfly Valve Series 61 Vic-300 MasterSeal Stainless Steel Butterfly Valve SERIES 761 SERIES 61 Read and

More information

Ball-Bearing Products

Ball-Bearing Products Ball-Bearing Products www.daytonlamina.com Check our website for the latest technical information. Ball-Bearing Components Contents Ball-Bearing Operating Data & Design Selection... 2 Ball-Bearing Component

More information

A =(4 WYLTP\T JVUULJ[PVUZ [\YU

A =(4 WYLTP\T JVUULJ[PVUZ [\YU A Vallourec brand Introduction Congratulations on selecting pipe threaded with VAM connections. This edition of the running book is a special one as we celebrate the 50th anniversary of VAM connections.

More information

PRESSURE RELIEF VALVE: DISASSEMBLY, INSPECTION, and ASSEMBLY CONTENTS

PRESSURE RELIEF VALVE: DISASSEMBLY, INSPECTION, and ASSEMBLY CONTENTS Page 1 of 35 PRESSURE RELIEF VALVE: DISASSEMBLY, INSPECTION, and ASSEMBLY CONTENTS 1. Overview 2. Disassembly of Valves with Liner Subs and press-in Bushing (Models 30525 and 30550). 2.1. Routine Disassembly

More information

FLOWSERVE CORPORATION NOBLE ALLOY VALVE BALL VALVE REPAIR INSTRUCTION

FLOWSERVE CORPORATION NOBLE ALLOY VALVE BALL VALVE REPAIR INSTRUCTION FLOWSERVE CORPORATION NOBLE ALLOY VALVE BALL VALVE REPAIR INSTRUCTION Cookeville Valve Operation 1978 Foreman Drive Cookeville, TN 38541 PH: 800-251-6761 931-432-4021 FAX: 931-432-5518 CONTENTS FLOWSERVE/NOBLE

More information

DIAMOND ROLLER CHAIN. For Agricultural and Construction Equipment

DIAMOND ROLLER CHAIN. For Agricultural and Construction Equipment DIAMOND ROLLER CHAIN For Agricultural and Construction Equipment FABRICATION While roller chain would appear to be a simple product, the number of components in a ten foot section of 40 pitch chain totals

More information

HAYWARD FLOW CONTROL TBH SERIES TRUE UNION BALL VALVE INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

HAYWARD FLOW CONTROL TBH SERIES TRUE UNION BALL VALVE INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS HAYWARD FLOW CONTROL TBH SERIES TRUE UNION BALL VALVE INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS Pg. 1 of 10 PLEASE READ THE FOLLOWING INFORMATION PRIOR TO INSTALLING AND USING HAYWARD TBH SERIES

More information

Top Drive System Installation and Commissioning Manual

Top Drive System Installation and Commissioning Manual TDS-1000A Top Drive System Installation and Commissioning Manual SM01040 General Information Conventions.............................. 1-3 Notes, Cautions, and Warnings......................... 1-3 Illustrations.........................................

More information

BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB DOUBLE ACTING SERIES PNEUMATIC ACTUATORS

BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB DOUBLE ACTING SERIES PNEUMATIC ACTUATORS ENGLISH LANGUAGE BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB DOUBLE ACTING SERIES PNEUMATIC ACTUATORS PART NUMBER: 068269E REVISION: "C" RELEASE DATE: December 2001 Page 1 of 12 CONTENTS

More information

CRANKSHAFT & MAIN BEARINGS

CRANKSHAFT & MAIN BEARINGS CRANKSHAFT & MAIN BEARINGS * PLEASE READ THIS FIRST * REMOVAL Ensure all main bearing caps are marked for location on cylinder block. Some main bearing caps have an arrow stamped on them. The arrow must

More information

Convertible - Rated 3 4-Ton /2-Ton Nylon Strap Hoists Refer to any questions about the use, application, repair or testing of this hoist to:

Convertible - Rated 3 4-Ton /2-Ton Nylon Strap Hoists Refer to any questions about the use, application, repair or testing of this hoist to: Operating and Servicing Instructions for Convertible - Rated 3 4-Ton - 1 1 /2-Ton Nylon Strap Hoists Refer to any questions about the use, application, repair or testing of this hoist to: Hubbell / Chance

More information

Butterfly valves Figure 56 Installation & Maintenance Instructions

Butterfly valves Figure 56 Installation & Maintenance Instructions KEYSTONE Please read these instructions carefully This symbol indicates important messages and safety instructions. Hazard potentials: disregarding of instructions improper use of product insufficiently

More information

Z Type Hydraulic Fishing Jar. Manual D430

Z Type Hydraulic Fishing Jar. Manual D430 Z Type Hydraulic Fishing Jar Manual D430 CONTENTS Z Type Hydraulic Fishing Jar Overview... 2 Use... 2 Construction... 2 Illustrations... 3 4 Operation... 5 Fishing Operations... 6 Jarring Procedure...

More information

Installation and Operating Instruction for Brake Caliper HW 150 HFA and HW 180 HFA E e

Installation and Operating Instruction for Brake Caliper HW 150 HFA and HW 180 HFA E e Installation and Operating Instruction for Brake Caliper HW 150 HFA and HW 180 HFA E 09.736e Schaberweg 30-38 Phone +49 6172 275-0 61348 Bad Homburg Fax +49 6172 275-275 Germany www.ringspann.com info@ringspann.com

More information

TECHNICAL BULLETIN

TECHNICAL BULLETIN Page 1 of 5 Stock No. H12 - HOLLAND SLIDER BRACKET PART NO. 53-30008-001 CONCEPT: This slider bracket is designed for mounting Holland 5th wheel load cells and top plates. This bracket can be used on standard

More information

Drill Collars. Drill collars from VAM Drilling are available with the following features:

Drill Collars. Drill collars from VAM Drilling are available with the following features: 73 Drill Collars Drill collars are thick-walled tubular pieces machined from solid steel bars, forming a component of the bottom hole assembly that provides weight-onbit for improved drilling performance.

More information

USER INSTRUCTIONS. NAF Trunnball DL Ball Valves. Installation Operation Maintenance. Experience In Motion FCD NFENIM A4 01/15

USER INSTRUCTIONS. NAF Trunnball DL Ball Valves. Installation Operation Maintenance. Experience In Motion FCD NFENIM A4 01/15 USER INSTRUCTIONS NAF Trunnball DL Ball Valves FCD NFENIM4168-01-A4 01/15 Installation Operation Maintenance Experience In Motion Contents SAFETY 3 1 General 3 2 Lifting 4 3 Receiving Inspection 4 4 Installation

More information

INSTRUCTION MANUAL. Anchor Darling 1878 Swing Check Valves. Installation Operation Maintenance. Sizes 1/2 through 2 FCD ADENIM

INSTRUCTION MANUAL. Anchor Darling 1878 Swing Check Valves. Installation Operation Maintenance. Sizes 1/2 through 2 FCD ADENIM INSTRUCTION MANUAL Anchor Darling 1878 Swing Check Valves Sizes 1/2 through 2 Installation Operation Maintenance FCD ADENIM0006-00 Table of Contents 1.0 Physical Description and Operation of Equipment

More information

Operating Procedures for GripTight High Pressure Test Plug

Operating Procedures for GripTight High Pressure Test Plug Page 1 of 13 Operating Procedures for GripTight High Pressure Test Plug Curtiss Wright Proprietary This document is the property of and contains information proprietary to Curtiss Wright and/or its subcontractors

More information

OVERLOAD CLUTCHES FOR INDEX DRIVES

OVERLOAD CLUTCHES FOR INDEX DRIVES The Driving Force in Automation OVERLOAD CLUTCHES FOR INDEX DRIVES WARNING WARNING This is a controlled document. It is your responsibility to deliver this information to the end user of the CAMCO indexer.

More information

NOTICE: Using old water pump seal installer J on the new water pump coolant seal will result in damage to water pump.

NOTICE: Using old water pump seal installer J on the new water pump coolant seal will result in damage to water pump. SERIES 60 SERVICE MANUAL Detroit Diesel previously released a water pump coolant seal which required the use of seal installer J 35988-19, part of tool set J 35988-D. This seal went into effect with engine

More information

Instruction Manual for HSPA Take-Up Units

Instruction Manual for HSPA Take-Up Units Installation Instruction Manual for HSPA Take-Up Units Warning: To ensure the drive is not unexpectedly started, turn off and lockout the power source before proceeding. Failure to observe these precautions

More information

D-15/G-15 Maintenance

D-15/G-15 Maintenance D-15/G-15 Maintenance NOTE: The numbers in parentheses are the Reference Numbers on the exploded view illustrations found later in this manual and in the Parts Manual. Daily Check the oil level and the

More information

DELTA STYLE 9500 CARTRIDGE SPLIT SEAL INSTALLATION INSTRUCTIONS INTRODUCTION:

DELTA STYLE 9500 CARTRIDGE SPLIT SEAL INSTALLATION INSTRUCTIONS INTRODUCTION: DELTA STYLE 9500 CARTRIDGE SPLIT SEAL INSTALLATION INSTRUCTIONS INTRODUCTION: The Type 9500 Cartridge Split Seal sets the standard in the evolution of split seal designs. It is well suited for the widest

More information

for ½" thru 2" 800 lb. Piston Lift Check Valves with Resilient Seat Option

for ½ thru 2 800 lb. Piston Lift Check Valves with Resilient Seat Option Manual No. 800-PC Issued: March 31, 2004 INSTRUCTION MANUAL for ½" thru 2" 800 lb. Piston Lift Check Valves with Resilient Seat Option Flowserve Corporation Flow Control Division 1900 S. Saunders Street

More information

GUIDELINES FOR HINGED AND BOLTED MANWAY ASSEMBLY

GUIDELINES FOR HINGED AND BOLTED MANWAY ASSEMBLY GUIDELINES FOR HINGED AND BOLTED MANWAY ASSEMBLY Assembly Instructions for the Ethanol Industry Published by: Renewable Fuels Association Authored by: Watco Compliance Services, VSP Technologies, and Salco

More information

KEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVES INSTALLATION AND OPERATION MANUAL

KEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVES INSTALLATION AND OPERATION MANUAL Before installation these instructions must be fully read and understood Intended valve use The valve is intended to be used only in applications within the pressure/temperature limits indicated in the

More information

MOTION DECOUPLED HYDRAULIC DELIVERY SYSTEM (MDHDS) ASSEMBLY AND DEPLOYMENT PROCEDURES

MOTION DECOUPLED HYDRAULIC DELIVERY SYSTEM (MDHDS) ASSEMBLY AND DEPLOYMENT PROCEDURES MOTION DECOUPLED HYDRAULIC DELIVERY SYSTEM (MDHDS) ASSEMBLY AND DEPLOYMENT PROCEDURES Prepared for the University of Texas by Pettigrew Engineering, PLLC Tom Pettigrew, PE President Revision: 5 15 October

More information

Installation, Operation and Maintenance Instructions Series 608 Ball Valve

Installation, Operation and Maintenance Instructions Series 608 Ball Valve b. With valve open, remove three body bolts, loosen fourth and swing out body. Remove fourth bolt and spread pipe ends Close valve, remove ball, seats, body seals. Return body to its original position

More information

Casing Running Tools (CRTi2-8.63)

Casing Running Tools (CRTi2-8.63) Casing Running Tools (CRTi2-8.63 CRTi Internal Grip Casing Running Tool Volant s CRTi casing running tool is designed f casing running drilling with top drive equipped rigs to makeup, breakout, reciprocate,

More information

PowerLevel s e r i e s

PowerLevel s e r i e s Owner s Manual Hydraulic Leveling CONTENTS Introduction Operation Control Panel Automatic Leveling Manual Leveling Retracting Jacks Remote Operation Care & Maintenance Troubleshooting Error Codes 1 2 2

More information

SERVICE MANUAL for. Engine-to-Generator. Part Number used on. John Deere Engine Driven Aircraft Ground Power Single-Bearing Generator Sets

SERVICE MANUAL for. Engine-to-Generator. Part Number used on. John Deere Engine Driven Aircraft Ground Power Single-Bearing Generator Sets TO-216 SERVICE MANUAL for Engine-to-Generator FLEXIBLE COUPLING Part Number 181267 used on John Deere Engine Driven Aircraft Ground Power Single-Bearing Generator Sets manufactured by HOBART BROTHERS COMPANY

More information

GT-200 GATE VALVES PN16, Screwed end

GT-200 GATE VALVES PN16, Screwed end Document No. : MD-QO-04-281 Date : 2009/07 /17 Version : 1.0 GT-200 GATE VALVES PN16, Screwed end USER MANUAL Modentic Industrial Corporation 14F-1,No.57Taya Rd.,Taichung,Taiwan,R.O.C. Email:modentic@ms9.hinet.net

More information

Model QED-D, QED-A, QED-L

Model QED-D, QED-A, QED-L This supplement is for Field Service use only, as complete dis-assembly and re-assembly of the QED reducer by the customer is NOT recommended. This supplement only extends to single reduction QED units.

More information

Bray/McCannalok High Performance Butterfly Valve Operation and Maintenance Manual

Bray/McCannalok High Performance Butterfly Valve Operation and Maintenance Manual Bray/McCannalok High Performance Butterfly Valve Operation and Maintenance Manual Table of Contents Definition of Terms 1 Introduction 1 Installation 1 Maintenance 2 Stem Seal Replacement 4 Seat Replacement

More information

Troubleshooting Guide for Pumps ATD ATD ATD5289

Troubleshooting Guide for Pumps ATD ATD ATD5289 PROBLEM: Your pump does not work? There are Three Basic Problems! Troubleshooting Guide for Pumps ATD5217 - ATD5219 - ATD5289 Air Motor Operates but nothing comes out. This is the most common problem.

More information

MUELLER GAS. No-Blo Valve. Changers. Reliable Connections. General Information 2-3. Plugging Unit Assembly 4-5. Removing Old Valve 5-6

MUELLER GAS. No-Blo Valve. Changers. Reliable Connections. General Information 2-3. Plugging Unit Assembly 4-5. Removing Old Valve 5-6 operating Instructions manual MUELLER GAS TAble of contents PAGE No-Blo Valve General Information 2-3 Plugging Unit Assembly 4-5 Removing Old Valve 5-6 Installing New Valve 6-7 Changers! WARNING: 1. Read

More information

I-231.T2S1/CLAD. Victaulic Style 231 Non-Restrained, Flexible Expansion Coupling with Cladding on Expansion Side of Pipe WARNING IMPORTANT INFORMATION

I-231.T2S1/CLAD. Victaulic Style 231 Non-Restrained, Flexible Expansion Coupling with Cladding on Expansion Side of Pipe WARNING IMPORTANT INFORMATION WARNING Read and understand all instructions before attempting to install any Victaulic piping products. Depressurize and drain the piping system before attempting to install, remove, or adjust any Victaulic

More information