Installation Instructions

Transcription

1 CLEAN FREESTANDING SINGLE CONTROL BATH FILLER Installation Instructions.9 Thank you for selecting American-Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. ROUGHING-IN DIMENSIONS FINISHED WALL 8-/8" (0mm) -/" (09mm) -/" (0mm) Certified to comply with ANSI A.8. M90 REV.. 8-/" (90mm) Recommended Tools " DIA. (0mm) -/" (mm) -/" (0mm) Phillips Screwdriver Flat Blade Screwdriver Tubing Cutter Pipe Wrench -/" Hole Saw -/" DIA. (0mm) FINISHED FLOOR /" SUPPLIES (mm) -/" (mm) T -CONNECTOR COLD Adjustable Wrench Electric Drill /"- NPT(mm) SUPPLY INLETS Channel Locks Teflon Tape

2 INSTALL SUPPLY HOSES AND RISER TUBES TO VALVE BODY CAUTION Turn off hot and cold water supplies before beginning. Thread Hot and Cold SUPPLY HOSES () into MANIFOLD using a wrench or adjustable wrench. Make sure the connections are tight. Use Red tape (not supplied) to indicate the Hot SUPPLY HOSE. SEE VIEW A Insert RISER TUBE () without the flange over SUPPLY HOSES (). Thread the RISER TUBE () into base of the VALVE BODY () and tighten fully. Slide the FLOOR MOUNTING FLANGE () onto the RISER TUBE () with the flange. Thread RISER TUBE () into the bottom of RISER TUBE () and fully tighten. Note: Be careful not to scratch the faucet while tightening the tube assembly. INSTALL BATH SPOUT AND HANDLE TO TUB FILLER Install SPOUT () into faucet body. Make sure O-RING () is installed and not damaged. Hand tighten SPOUT NUT (). Align and center the SPOUT () with the center line of the faucet body. With an adjustable wrench fully tighten the SPOUT NUT (). Note: Be careful not to scratch faucet while tightening SPOUT (). Insert HANDLE () on CARTRIDGE STEM, tighten SET SCREW () with HEX WRENCH () supplied. Install INDEX BUTTON () into HANDLE (). VIEW A H SUPPLY MANIFOLD H C C COLD SUPPLY VIEW A FAUCET BODY CARTRIDGE STEM H SUPPLY FLANGE M90 REV..

3 DETERMINE MOUNTING LOCATION FIGURE. Determine the distance from the finished wall to the center of the floor water supply holes and mark a centerline. Note: Check that floor is level in both directions. Drill a " (mm) diameter hole for the /" Hot and Cold supplies. Slide MOUNTING FLANGE () downwards on the TUB FILLER ASSEMBLY (). Place MOUNTING FLANGE () over the floor supply hole. Align and center the TUB FILLER ASSEMBLY (). FINISHED WALL LINE BASE BOARD FIGURE () " (mm) DIA. HOLE Level FIGURE. With the TUB FILLER ASSEMBLY () aligned and in desired position, mark on the floor the three mounting holes for the MOUNTING FLANGE (). FIGURE FIGURE. Drill three /" (mm) diameter holes -/" (mm) deep. Install the three ANCHORS () supplied, flush with the top of the finished floor. FIGURE M90 REV..

4 INSTALL TUB FILLER ASSEMBLY INSTALL WATER SUPPLIES AND T ADAPTER FIGURE : Make sure FLEXIBLE and COLD WATER SUPPLIES protrude through the " (mm) diameter hole in the floor enough to make the supply connections to the T ADAPTER (). FINISHED FLOOR SUB-FLOOR FIGURE COLD -/" (mm) /" SUPPLIES (mm) FIGURE : Hold the TUB FILLER ASSEMBLY () in place and install the three MOUNTING SCREWS (). Check aligment and level before fully tightening the MOUNTING SCREWS (). After tightening the MOUNTING SCREWS () push in the three PLUG BUTTONS (). FIGURE FIGURE : Apply sealing tape to the threads of the T ADAPTER () and the two SUPPLY ADAPTERS (). Thread the two SUPPLY ADAPTERS () onto the T ADAPTER () and tighten fully. From below the floor, connect the WATER SUPPLY HOSE () (marked with red) to the Hot water supply from the T () and the COLD WATER SUPPLY HOSE () to Cold water supply from the T (). Use an adjustable wrench or /8" open end wrench to tighten connections. Do not over tighten. Secure piping below floor to floor joist. FIGURE RED () /"- NPT (mm) COLD SUPPLY /"- NPT (mm) PIPE SUPPORT SEALING TAPE SUPPLY M 9 0 R E V..

5 INSTALL HAND SHOWER Install SEALS () on both ends of the SPRAY HOSE () and connect the one end with the hex nut to the TUB FILLER ASSEMBLY () using an adjustable wrench. Hand tighten the connection to the HAND SHOWER (). Note: When not in use, the HAND SHOWER () should be seated in the HOLDER (). HEX NUT 8 TEST INSTALLED FAUCET Move HANDLE () into off position and remove AERATOR (). Turn on water supplies and check all connections for leaks. Operate HANDLE () on to off, hot and cold to flush water lines thoroughly. Lift HAND SHOWER () from the holder and direct spray into tub. Pull DIVERTER KNOB (8) and check HAND SHOWER () and HOSE () connections for leaks. Push DIVERTER KNOB (8) in and place HAND SHOWER () into HOLDER (). CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. M90 REV..

6 CLEAN FREESTANDING SINGLE CONTROL BATH FILLER MODEL NUMBERS.9 M90-000A HAND SPRAY M A AERATOR ASSEMBLY M90-000A DIVERTER ASSEMBLY M A HAND SPRAY HOSE KIT M90-000A HANDLE KIT M9-000A SUPPLYHOSES M90-000A CARTRIDGE M A SCREW & ANCHOR KIT M90 REV.. M A T-CONNECTOR ASSEMBLY LINE FOR HELP For toll-free information and answers to your questions, call: Weekdays 8:00 a.m. to :00 p.m. EST IN CANADA (TORONTO ) Weekdays 8:00 a.m. to :00 p.m. EST IN MEXICO Product names listed herein are trademarks of American Standard Inc. AS America, Inc. 0