CB500X Valve Checking/Adjustment Guide. Before starting:

Size: px
Start display at page:

Download "CB500X Valve Checking/Adjustment Guide. Before starting:"

Transcription

1 Before starting: Removing the tank is much easier when it doesn t have much fuel in it. Consider running the tank to a low petrol level before starting the job. Forum members in both the UK & USA have struggled with availability of new shims from Honda, with them often being on back order for a week or more. Consider; if you can have your bike in the workshop for a week plus, if you are happy to dismantle the bike twice (once to measure and once to fit new shims) or if you can find a source of non-oem shims (e.g. Hot Cams kit) Tools required: 2mm/3mm Allen key (for removing plastic clips and hooking rockers into place) 5mm Allen key 6mm Allen key 10mm spanner 8mm socket 10mm socket 13mm socket 17mm socket for crank cover plate M6 bolt Cross head (Phillips) screwdriver Large flat head screwdriver Feeler gauges Micrometer or Vernier Calipers accurate to +/- 0.01mm Magnetic pickup tool (recommended!) Remove Seat Remove Side Panels Remove 2x 5mm allen bolts:

2 and pull panel out of rubber grommets, starting at the rear, to release: Remove Front Fairing Side Panels Remove inner fairing panel by pushing in the centre of the plastic clip, using a small allen key, or similar, and removing allen bolt (5mm) from top of tank Remove remaining 5mm allen bolts holding panel and plastic Phillips screw clip (also see second photo). First photo shows bolt locations once panel is removed:

3 Location of plastic Phillips screw fastener on inside front of the panel Pull the panel away from the bike at the rear to release the velcro patch and then pull forwards to release plastic lugs from slots in the centre fairing panel. Slots on centre panel:

4 Lugs on inside of fairing side panel: Remove Tank Unscrew 2x 8mm bolts securing front of tank to bike

5 Pull up the front of the tank so that it pivots on the rear mounting bolt. Remove the 2x rubber drain pipes to the bottom front of the tank the electrical plug midway down the left-hand side of the tank (pinch to release) and the fuel pipe from the pump (pinch white connector clip to release). A small amount of fuel will escape, but this will be minimized if the end of the pipe is kept on the airbox. Once the pipes and electrical connector are released, the rear bolt (10mm) can be removed to release the tank.

6 Remove Hazard Relay and ECU The ECU and Hazard Relay are located just behind the headstock on the under-tank tray. Pull the Hazard Relay up off its mount and release the electrical connector in the base. Remove the Relay and push the connector back through the under-tray. Disconnect the multiplug from the base of the ECU and remove the ECU by pulling it forwards and up through the rubber mounting band.

7 Release the rubber mounting band from the under-tank tray. Disconnect feed wires (x4) to coils

8 Release the wiring loom securing clips so that the loom can be lifted away from the tray Removing the under-tank tray Remove the 10mm nut and bolt securing the PAIR valve to the under-tank tray and slide off the spigot, so that it is no longer attached to the tray

9 Unclip the electrical connector secured to the outside left of the tray Carefully lever the clutch and throttle cables out of the retaining clip on the right side of the tray. Remove the 10mm bolt securing the front of the tray to the frame

10 Carefully lift and maneuver the tray up and out of the frame. Release the right side first and pull off the plug caps to allow the caps and leads to come away with the tray. Then lift the front of the tray up and maneuver the tray away from the wiring on the left side, taking care not to damage the connector mounting clips Removing the PAIR valve Release the clips from the ends of the pipes and disconnect the PAIR valve pipes from the cam cover and airbox. Unclip the fuel hose from the PAIR hose and the electrical connector to the valve. Then remove the PAIR valve complete with hoses

11 Disconnect Throttle and Clutch cables To keep the throttle free-play, loosen the locknut on the rear throttle cable and count the number of turns up to the top of the adjuster. Make a note of this for use in reassembly. Unscrew the adjuster to release the cable from the bracket and then free the cable from the throttle pulley

12 Unscrew the front cable to release this too (Optional, but makes life easier on ABS bikes) Unscrew the 5mm allen bolt on the top of the clutch cover, securing the clutch cable bracket. Release the bracket and unhook the cable Pull the cables up through the frame and lay them out to side, so they are out of the way.

13 Remove the rubber heat shield The heat shield stretches from the radiator at the front back to the frame above the cam cover. It is installed under the top radiator hose, so can only be swiveled out of the way to the right. To do this, unloop the ends of the shield from around the frame. Next remove the radiator top mounting bolt (10mm) and pivot the radiator forwards enough for the shield to be stretched over the top of the mount: Release the shield from the left and right radiator lugs to enable it to be swiveled out to the right side of the bike. Release brake pipes (ABS models only) Unscrew the 10mm brake pipe mounting bolt to the right of the radiator top mount and the bracket just inside the front of the frame to give the brake pipes some slack. Unclip the 2 white brake line securing clips on the inside of the right frame member and remove the clips. This enables the brake pipes to move slightly up and out giving more room to remove the cam cover

14 Remove cam cover Unclip and remove the breather hose from the back of the cam cover Unbolt the 4x 10mm bolts securing the cam cover in place. The cam cover should now be free to lift upwards, although it might need some persuasion to move. Once loose, maneuver the cover backwards out through the frame, tilting it up on the right, so clear the cam sprockets. It will be necessary to push the radiator top hose forwards and left and, on ABS models, the brake pipes up and right to enable the cover to come out.

15 Check valve clearances Remove the crankcase cover using a 17mm socket

16 Using a 14mm socket on the crankshaft end nut, rotate the engine until the T mark lines up with the nick at the front of the casing. The IN and EX marking on the rear cam sprocket should line up with the top of the head With these marks lined up, it is now possible to check the Exhaust valves (front camshaft). The gap should be 0.27mm +/-0.03mm If the gap needs adjusting, then it is necessary to remove the rocker shaft so that the shims can be removed and measured. Unscrew the 6mm allen retaining bolt from the left of the engine and screw an M6 bolt a few turns into the end of the rocker shaft

17 Pull the rocker shaft out of the head to release the rocker arms.

18 With the rocket shaft removed, the rockers can be pushed away from the valves and the shims removed. I used a magnetic pickup tool to get the shims out and remove them from the engine without danger of them dropping into it. Once the shim is removed, use a micrometer or Vernier caliper to measure its thickness. It is then possible to work out the size of the new shim required: New shim = Old shim (0.27 Actual gap) e.g. If the gap was 0.21 and the old shim was 2.12 the calculation would be New shim = 2.12 ( ) = = 2.06 Install the new shim in the top of the valves and re-install the rocker shaft, moving the rockers back into position so the shaft can pass through.

19 Turn the crank bolt 1/2 a turn clockwise, so that the marks on the camshaft sprockets look like this: Repeat the clearance checking and shim measurement/replacement (as necessary) on the Inlet valves (rear camshaft). The gap should be 0.16mm +/-0.03mm To calculate the new shim size on the inlet valves, use the following formula: New shim = Old shim (0.16 Actual gap) Reassembly Reassembly is the reverse of dismantling. The only thing to watch for is ensuring the front of the fairing side panels are correctly aligned as this has to be done as the panel is slid into place, before any fixings are put in.

Prerequisites: Shop Manual (recommended) pages 3-9 through 3-13.

Prerequisites: Shop Manual (recommended) pages 3-9 through 3-13. Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961

More information

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar Timing Chain Renew ( 34 0) Special Tools 40 400 40 Engine support bar 40 0 Adaptor for -40 40 03 Adaptor for -40 Proprietary Tools Scraper Workshop Equipment Transmission jack Materials Cable ties Sealer

More information

Timing Chain - Renew ( )

Timing Chain - Renew ( ) «Scorpio '95 Table of Contents» «Section 21: Engine» «Subsection 21-05: 2,9 V6 24V Cosworth Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 21-140-01Adaptor for 21-140

More information

Your G3 buggy is fitted with three switches on the front part of the body:

Your G3 buggy is fitted with three switches on the front part of the body: CONTENTS Buggy operation... 3 General Maintenance... 5 Technical Maintenance... 6 Front wheel bearing replacement... 6 Rear wheel bearing replacement... 7 Chain replacement... 8 Chain Adjustment... 9 Brake

More information

Holden VE SIDI series II V6 OTR CAI Installation Instructions

Holden VE SIDI series II V6 OTR CAI Installation Instructions Holden VE SIDI series II V6 OTR CAI Installation Instructions 1 P a g e Shown above is a standard V6 VE LFW SIDI engine bay. Your MAF Loom may need to be extended by an auto electrician. Please check the

More information

Pistons and Connecting Rods, Remove and Install

Pistons and Connecting Rods, Remove and Install Page 1 of 46 Pistons and Connecting Rods, Remove and Install Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release

More information

CLUTCH CABLE REPLACEMENT GUIDE FOR THE FOLLOWING PRODUCTS 2004 ONWARDS

CLUTCH CABLE REPLACEMENT GUIDE FOR THE FOLLOWING PRODUCTS 2004 ONWARDS 1 Issue 2 CLUTCH CABLE REPLACEMENT GUIDE FOR THE FOLLOWING PRODUCTS 2004 ONWARDS Mountfield 460R PD Briggs & Stratton Sprint Engine. Mountfield 460R PD/ES Briggs & Stratton Quantum Engine. Mountfield 460R

More information

Engine and A4LDE Automatic Transmission Remove and Install ( ) Remove

Engine and A4LDE Automatic Transmission Remove and Install ( ) Remove Engine and A4LDE Automatic Transmission Remove and Install ( 3 0) Special Tools 068A -068A Engine lifting bracket -540 Bolt tightening angle gauge Workshop Equipment Transmission jack Workshop crane Assembly

More information

Triumph Tiger 800. Torque settings. Torque (Nm) Camshaft cover to cylinder head 10 Camshaft drive chain tensioner to head 9

Triumph Tiger 800. Torque settings. Torque (Nm) Camshaft cover to cylinder head 10 Camshaft drive chain tensioner to head 9 Triumph Tiger 800 Torque settings Cylinder Head Camshaft cover to cylinder head 10 Camshaft drive chain tensioner to head 9 Camshaft bearing ladder to head Camshaft sprocket to camshaft 10 Camshaft drive

More information

3-10 MAINTENANCE INSTALLATION. TORQUE: IS N m (1.6 kgf m, 121bHt)

3-10 MAINTENANCE INSTALLATION. TORQUE: IS N m (1.6 kgf m, 121bHt) MAINTENANCE INSTALLATION Install and hand tighten the spark plug [1] to the cylinder head, then tighten the spark plug to the specified torque using a spark plug wrench. TORQUE: IS N m (1.6 kgf m, 121bHt)

More information

Installation Instructions : Audi C7 RS6 Intake System : Page 1

Installation Instructions : Audi C7 RS6 Intake System : Page 1 Installation Instructions : Audi C7 RS6 Intake System : Page 1 1. Remove Engine cover and loosen the clamps around the inlet hoses of the airbox. 2. Pull the hoses away from the turbo tubes. 3. Release

More information

VALVE CLEARANCE (K3-VE)

VALVE CLEARANCE (K3-VE) ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT

More information

DIY: Shiver Valve Check, Illustrated

DIY: Shiver Valve Check, Illustrated DIY: Shiver Valve Check, Illustrated By Petemoss, AF1 Forum Tools needed: 4mm allen wrench to remove all the fairing pieces 2.5mm allen wrench to remove battery holder 5mm allen wrench for valve cover

More information

Remove Air Cleaner Cover and. Filter

Remove Air Cleaner Cover and. Filter Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove

More information

XL HYDROSTATIC TRANSAXLES

XL HYDROSTATIC TRANSAXLES Purging Procedures Due the effects air has on efficiency in hydrostatic drive applications, it is critical that it be purged from the system. These purge procedures should be implemented any time a hydrostatic

More information

AmTryke Adult Recumbent Model HP1000 #50-HC-1000

AmTryke Adult Recumbent Model HP1000 #50-HC-1000 AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

Engine Dismantle and Assemble ( )

Engine Dismantle and Assemble ( ) Engine Dismantle and Assemble ( 34 8) Special Tools 5 053 Slide hammer 47 Vibration damper remover 47 5053 00 Splined head socket, cylinder head bolts 87 Mounting stand with geared drive 00 059C Installer

More information

1.6L 4-CYL - VIN [E]

1.6L 4-CYL - VIN [E] 1.6L 4-CYL - VIN [E] 1993 Nissan Sentra 1993 NISSAN ENGINES 1.6L 4-Cylinder NX, Sentra * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES

More information

Installation Instructions

Installation Instructions Part Number: 10.109.01.109 Description: AUTOTECH Sport 270 Hydraulic Camshaft Note: If the job seems to be beyond your abilities, we recommend that you refer this installation to a qualified mechanic.

More information

MAZDA 3 MPS FRONT MOUNTING INTERCOOLER INSTALLATION

MAZDA 3 MPS FRONT MOUNTING INTERCOOLER INSTALLATION MAZDA 3 MPS FRONT MOUNTING INTERCOOLER INSTALLATION Tools needed: 7mm Hose clamp driver 10mm,12mm sockets and suitable ratchet with extensions Flat bladed screwdriver Pliers Phillips screwdriver KIT CONTENTS

More information

Disassembly and Assembly

Disassembly and Assembly SENR9973-01 September 2007 Disassembly and Assembly 400C Industrial Engine HB (Engine) HD (Engine) HH (Engine) HL (Engine) HM (Engine) HN (Engine) HP (Engine) HR (Engine) Important Safety Information Most

More information

Installation Manual v1.0: RPM Governor Spring Installation Dodge. Please read all instructions before installation.

Installation Manual v1.0: RPM Governor Spring Installation Dodge. Please read all instructions before installation. Installation Manual v1.0: 705-940-2164 4000 RPM Governor Spring Installation 1994-98 Dodge Please read all instructions before installation. The stock governor springs begin to restrict fuel rack travel

More information

Fiat X1/9 1500cc Engine Timing Belt Replacement, Cam Timing and Static Ignition Timing. Photos courtesy of Don Doan.

Fiat X1/9 1500cc Engine Timing Belt Replacement, Cam Timing and Static Ignition Timing. Photos courtesy of Don Doan. Fiat X1/9 1500cc Engine Timing Belt Replacement, Cam Timing and Static Ignition Timing. Photos courtesy of Don Doan. Introduction This document outlines how to replace a timing belt on a Fiat X1/9 1500cc

More information

VALVE CLEARANCE INSPECTION

VALVE CLEARANCE INSPECTION EM4 ENGINE MECHANICAL (5VZFE) INSPECTION EM01E10 Inspect and adjust the valve clearance when the engine is cold. 1. REMOVE INTAKE AIR CONNECTOR (See page EM29) 2. REMOVE CYLINDER HEAD COVERS (See page

More information

Workshop manual XP

Workshop manual XP Workshop manual 0 5 6XP 50 5 5 English Workshop manual Husqvarna 0/5/6XP/50/5/5 Contents Introduction... Safety regulations... General instructions... Special instructions... Special tools... Technical

More information

Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.

Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Put the urethane bushings into the upper antiroll-bar-link eyebolt. Coat the bushings

More information

TIMING CHAIN COMPONENTS

TIMING CHAIN COMPONENTS h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:

More information

This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX

This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX Adjusting the valve clearance on a 2L V6 FTO engine This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX Disclaimer: This guide is to assist you

More information

Service Bulletin Cylinder Head Service. September 17, 2002

Service Bulletin Cylinder Head Service. September 17, 2002 Service Bulletin 02-047 Applies To: 1998 02 Passport ALL September 17, 2002 Cylinder Head Service BACKGROUND In the 1998 through 2002 Passport Service Manuals, some of the information on cylinder head

More information

Engine Remove and Install ( ) Remove. 2,5l TCI Diesel Engine. Special Tools. Workshop Equipment Transmission jack Trolley jack Workshop crane

Engine Remove and Install ( ) Remove. 2,5l TCI Diesel Engine. Special Tools. Workshop Equipment Transmission jack Trolley jack Workshop crane Engine Remove and Install ( 34 0) Special Tools 068 A 068A Engine lifting tackle 4 003 Coolant hose clamp removal and fitting tool Workshop Equipment Transmission jack Trolley jack Workshop crane Materials

More information

AmTryke Adult Recumbent Model JT2000 #50-FC-2000

AmTryke Adult Recumbent Model JT2000 #50-FC-2000 AmTryke Adult Recumbent Model JT2000 #50-FC-2000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

Gearbox sectional drawing

Gearbox sectional drawing Gearbox sectional drawing BMW Grafik Design MT- KL39000 3.5 3.6 3 4 77 3 4 77 3473 3 4 7 3 4 7 3 4 73 KL300 Replacing the shaft sealing rings in the gearbox housing and gearbox cover All shaft sealing

More information

1992 Mitsubishi 3000GT VR-4

1992 Mitsubishi 3000GT VR-4 TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner

More information

Installation Instructions Camaro ZL1 ( Z) ( ZB)

Installation Instructions Camaro ZL1 ( Z) ( ZB) Installation Instructions Camaro ZL1 (501-1099-10-Z) (501-1099-10-ZB) Parts List 1 Insulated Air Box \ Lid 1 Thermal Coated Intake Tube / MAF Housing with (2) M4 x.7 thread 8mm long Stainless Screws; 1

More information

Sherco Setup and Lubrication Guide

Sherco Setup and Lubrication Guide Sherco Setup and This guide is designed to provide the Sherco owner with instructions on how to: Set up a new bike Clean and re-oil the air filter Change the transmission oil Change the fork oil Repack

More information

E70PL4EEC 1999 : CAMSHAFT [1/23] Page 1 of 49

E70PL4EEC 1999 : CAMSHAFT [1/23] Page 1 of 49 E70PL4EEC 1999 : CAMSHAFT [1/23] Page 1 of 49 E70PL4EEC 1999 : CAMSHAFT [1/23] 1 5030657 1 CAMSHAFT 2 5030658 1 PLATE, Camshaft thrust 3 5030549 1 SEAL, Camshaft 4 5030989 2 BOLT, Plate 5 5030663 8 ARM,

More information

REPLACEMENT GEAR CHANGE CABLES Installation Guide

REPLACEMENT GEAR CHANGE CABLES Installation Guide Some sections are from the Lotus Service Manual V6: REPLACEMENT GEAR CHANGE CABLES Installation Guide For additional assistance, send questions by email to cables@lotusm100.com Copyright 2013 lotusm100.com

More information

Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical condition is okay.

Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical condition is okay. Page 1 of 11 ARTICLE BEGINNING INTRODUCTION Introduction information not applicable. ENGINE MECHANICAL Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical

More information

MITSIBUSHI FTO NUT,BOLT AND TORQUE GUIDE

MITSIBUSHI FTO NUT,BOLT AND TORQUE GUIDE MITSIBUSHI FTO NUT,BOLT AND TORQUE GUIDE All information below has been obtained from the official Mitsubishi fto workshop manual, and I hold no liability for any incorrect information. Heads marked 4

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

Slave Cylinder Weep Hole Drilling Procedure

Slave Cylinder Weep Hole Drilling Procedure Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key

More information

Engine Dismantle and Assemble ( )

Engine Dismantle and Assemble ( ) Engine Dismantle and Assemble (2 34 8) Special Tools 2-036A Remover for pilot bearing 2-37 Oil seal installer/aligner 237 2036A 2-044A Installer/Aligner, Pilot Bearing/Clutch Plate 244 2-44 Inlet manifold

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

CHASSIS CONTENTS EXTERIOR PARTS 6-1 FRAME COVER 6-2 REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-10 HANDLEBARS 6-17 FRONT FORK 6-19

CHASSIS CONTENTS EXTERIOR PARTS 6-1 FRAME COVER 6-2 REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-10 HANDLEBARS 6-17 FRONT FORK 6-19 CHASSIS CONTENTS EXTERIOR PARTS 6- FRAME COVER 6- REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-0 HANDLEBARS 6-7 FRONT FORK 6-9 STEERING 6-6 REAR WHEEL 6-3 REAR BRAKE 6-39 6 REAR SHOCK ABSORBER 6-43

More information

Timing Chain Renew ( ) Remove. 2,0 DOHC-8V Engine. Special Tools Angle gauge A Universal flange-holding wrench

Timing Chain Renew ( ) Remove. 2,0 DOHC-8V Engine. Special Tools Angle gauge A Universal flange-holding wrench Timing Chain Renew ( 34 0) Special Tools 5-030A Universal flange-holding wrench 540-540 Angle gauge 5030A -47 Remover for vibration damper 68-68 Crankshaft immobilising tool 47 Remove. Standard preparatory

More information

Installation Instructions : Ford Focus MK3 RS : Page 1 Tools Required: Philips screwdriver, trim removal tool, Torx, 10mm socket

Installation Instructions : Ford Focus MK3 RS : Page 1 Tools Required: Philips screwdriver, trim removal tool, Torx, 10mm socket Installation Instructions : Ford Focus MK3 RS : Page 1 Tools Required: Philips screwdriver, trim removal tool, Torx, 10mm socket 1 Rotate the temperature sensor on the inlet to the airbox anti-clockwise

More information

Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed

Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake

More information

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation. TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan

More information

Edition Manual Chapter Page Workshop Manual, Stiga Park 5 Belts 11

Edition Manual Chapter Page Workshop Manual, Stiga Park 5 Belts 11 2008-05-19 Workshop Manual, Stiga Park 5 Belts 11 Pro 20 1. Dismantle the belts A and B as described above. 2. Block up the rear frame and remove the right rear wheel. Clean carefully the insex hole in

More information

Rekluse Motor Sports. The z-start Clutch CRF 250R. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision RMS112 CRF 250R

Rekluse Motor Sports. The z-start Clutch CRF 250R. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision RMS112 CRF 250R Rekluse Motor Sports The z-start Clutch CRF 250R Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS112 CRF 250R 191-212 Manual Revision: 091205 Rekluse Motor Sports, Inc.

More information

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with

More information

Special Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for

More information

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting

More information

IE Audi 3.0T Crank Pulley Upgrade Install Guide IEBAVJ3

IE Audi 3.0T Crank Pulley Upgrade Install Guide IEBAVJ3 IE Audi 3.0T Crank Pulley Upgrade Install Guide IEBAVJ3 Thank you for purchasing your IE 3.0T crankshaft pulley upgrade! This instruction guide is used for installation of IE s lower overdrive pulley for

More information

Procharger Stage II Intercooled Supercharger System (11-14 GT)

Procharger Stage II Intercooled Supercharger System (11-14 GT) Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2

More information

AB65HCTR Maxogen Kit

AB65HCTR Maxogen Kit AB65HCTR Maxogen Kit For Honda EP3 Civic Type-R & DC5 Integra 1 AB65HCTR Performance Air Box Kit Contents Qty Description Airbox Assembly 1 X AB65H Carbon Air Box 1 X Carbon Fibre Air Filter Retaining

More information

Öhlins Front Fork for. Motocross and Enduro. Owner s Manual

Öhlins Front Fork for. Motocross and Enduro. Owner s Manual Öhlins Front Fork for Motocross and Enduro Owner s Manual Safety Precautions The front fork is a very important part of the vehicle and will therefore affect the stability. Read and make sure that you

More information

3. Engine XCITING 400i. This chapter covers the location and servicing of the engine components for the KYMCO Xciting 400i.

3. Engine XCITING 400i. This chapter covers the location and servicing of the engine components for the KYMCO Xciting 400i. 3. Engine XCITING 400i Engine This chapter covers the location and servicing of the engine components for the KYMCO Xciting 400i. Engine Removal... 3-4~3-12 Cylinder Head Cover... 3-13~3-17 Camshaft...

More information

https://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/40/ tr.html

https://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/40/ tr.html Page 1 of 7 NOTE: The timing pin is used to accurately locate TDC for setting the overhead. The timing pin is typically located below the fuel pump. for front gear train engines, in the front gear housing

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi without stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi without stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0921 APPLICATION 2007-08 E92 335i/xi without stock oil cooler Congratulations for being selective enough to use a Dinan Engineering Oil Cooler

More information

Removing and installing toothed belt

Removing and installing toothed belt Page 1 of 10 Special tools and workshop equipment required Diesel injection pump locking pin -3359- (2x) Pin wrench -T10020- Crankshaft stop -T10050- for engines with circular crankshaft sprocket Locking

More information

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info* DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for

More information

KUBOTA WATER-COOLED DIESEL ENGINE

KUBOTA WATER-COOLED DIESEL ENGINE SPARE PARTS CATALOGUE KUBOTA WATER-COOLED DIESEL ENGINE MODEL: E75N E75NB3 0001 010 14418-0101-0 Crankcase Compl. 1 1 0001 020 14971-2671-0 Plug, Seal 2 2 0001 030 14301-3363-0 Pin Plug 2 2 0001 040 05012-00612

More information

XRT300 AND XRT350 BA XR6 TURBO UPGRADE KIT FITTING INSTRUCTIONS

XRT300 AND XRT350 BA XR6 TURBO UPGRADE KIT FITTING INSTRUCTIONS XRT300 AND XRT350 BA XR6 TURBO UPGRADE KIT FITTING INSTRUCTIONS The use of NFU (No Further use) and REUSE (Re Use) relates to the individual parts storage when performing the upgrade. Also note that all

More information

INSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH)

INSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-17 CHEVROLET CRUZE 1.4T ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK

More information

Rekluse Motor Sports. The z-start Clutch CRF 250X. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision RMS116 CRF 250X

Rekluse Motor Sports. The z-start Clutch CRF 250X. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision RMS116 CRF 250X Rekluse Motor Sports The z-start Clutch CRF 250X Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS116 CRF 250X 191-216 Manual Revision: 103105 Rekluse Motor Sports, inc.

More information

Chapter 5 Part B: Ignition system - transistorised type

Chapter 5 Part B: Ignition system - transistorised type 5B 1 Chapter 5 Part B: Ignition system - transistorised type Contents Coil - testing........................................... 9 Distributor - overhaul..................................... 7 Distributor

More information

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) 2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475

More information

Cylinder head/gasket, replacing

Cylinder head/gasket, replacing 1(16) Cylinder head/gasket, replacing Special tools: 951 2666, 951 2767, 999 5450, 999 5452, 999 5454, 999 5670, 999 5718, 999 5719, 999 5750, 999 5972 Removing the cylinder head gasket Note! As the illustrations

More information

6. Remove OEM bolts from engine at locations A, B, and C. Lay the wiring off to the side.

6. Remove OEM bolts from engine at locations A, B, and C. Lay the wiring off to the side. 700359 DewEze Clutch Pump Kit #700359 Ford 5.4L, 6.8L w/ and w/o A/C AA mount 1999- INSTALLATION INSTRUCTIONS 1. Disconnect the battery. 2. Drain the radiator. 3. Remove the air cleaner assembly. 4. Remove

More information

88cc Big Bore Kit Install Instructions

88cc Big Bore Kit Install Instructions 88cc Big Bore Kit Install Instructions Before installing a big bore kit, you should first install a high volume oil pump. A high volume oil pump will deliver up to 300% more oil to your top end which will

More information

VALVE CLEARANCE INSPECTION

VALVE CLEARANCE INSPECTION ENGINE MECHANICAL (2RZFE, 3RZFE) INSPECTION EM5 EM02K06 Inspect and adjust the valve clearance when the engine is cold. 1. REMOVE INTAKE AIR CONNECTOR (See page EM34) 2. REMOVE PCV HOSES 3. REMOVE IGNITION

More information

REGULATION OF YAMAHA SUNDAY RACE RACE 2017

REGULATION OF YAMAHA SUNDAY RACE RACE 2017 1. ENGINE SPECIFICATIONS 1.1. Engine Type 4 Stroke Single Cyl 4 Stroke Single Cyl 4 Stroke Single Cyl 1.1.1. Displacement Up to 150cc Up to 150cc Up to 150cc 1.1.2. Engine Layout vertical vertical vertical

More information

WORKSHOP MANUAL TECHNICAL NETWORK LEADERSHIP WORKSHOP MANUAL 125 CC/150 CC 4-STROKE ENGINE

WORKSHOP MANUAL TECHNICAL NETWORK LEADERSHIP WORKSHOP MANUAL 125 CC/150 CC 4-STROKE ENGINE WORKSHOP MANUAL TECHNICAL NETWORK LEADERSHIP WORKSHOP MANUAL - 5 CC/50 CC 4-STROKE ENGINE Workshop manual Technical network leadership TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS... CHARACTERISTICS...

More information

1998 Saab 900 SE ENGINES Saab 2.0L & 2.3L 4-Cylinder

1998 Saab 900 SE ENGINES Saab 2.0L & 2.3L 4-Cylinder Removal & Installation See VALVE SPRINGS under CYLINDER HEAD under OVERHAUL. CAMSHAFT Removal 1. Rotate crankshaft until "0" mark on flywheel aligns with timing mark on flywheel cover. Remove inspection

More information

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic

More information

Illustrated Parts Manual

Illustrated Parts Manual 1 10 Illustrated Parts Manual 2 425 CR EFT Model Number A2011IRK4CETR (Red) S H A R E O U R PA S S IO N. TM TABLE OF CONTENTS 2011 ATV 425 CR EFT Red (A2011IRK4CETR) FRONT RACK, BODY PANEL, AND HEADLIGHT

More information

Fitting instructions for Lynx R Fairing CRF 250L

Fitting instructions for Lynx R Fairing CRF 250L Fitting instructions for Lynx R Fairing CRF 250L Thank you for purchasing the Lynx fairing. We hope the design features will extend the enjoyment of your CRF. Parts List 1 x Fairing and screen with two

More information

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available

More information

Cylinder Head, Remove and Install (Z 22 SE)

Cylinder Head, Remove and Install (Z 22 SE) Page 1 of 29 Cylinder Head, Remove and Install (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release the

More information

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES TEST AND ADJUSTMENT Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking (Minimum).......................... 28 kpa (4 psi) Oil Pressure.....................................

More information

Timing Chain, Balancer Shaft, Replace (Z 22 SE)

Timing Chain, Balancer Shaft, Replace (Z 22 SE) Page 1 of 34 Timing Chain, Balancer Shaft, Replace (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release

More information

HD372A DISASSEMBLY SLIDES

HD372A DISASSEMBLY SLIDES COMPRESSORS 03/93 CB-128 HD372A DISASSEMBLY SLIDES Each slide has a descriptive paragraph. Each paragraph has the main points outlined so reading the full text word for word is not necessary when presenting

More information

ILLUSTRATED PARTS MANUAL

ILLUSTRATED PARTS MANUAL ILLUSTRATED PARTS MANUAL 700 EFT Model Number A2014IBT4EETG TM SHARE OUR PASSION. www.arcticcat.com TABLE OF CONTENTS 2014 ATV 700 EFT (Model No. A2014IBT4EETG) FRONT RACK, BODY PANEL, AND HEADLIGHT ASSEMBLIES...

More information

Timing belt change. Timing belt change

Timing belt change. Timing belt change Timing belt change Put 2 new Gates T275 timing belts on today. Tensioner drilled smooth and tight with less than 16,000 miles on her decided not to change the tensioners just the belts. You'll need some

More information

Master Engine Timing Tool Set

Master Engine Timing Tool Set Master Engine Timing Tool Set Ford K 10551 www.kamasatools.com Pack Layout AC V O B C U D M Z S J W W N F Y K/L Q T AD P A H R AB AA E X G I Component identity Part No. OEM Ref Description A 23002-45D

More information

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION 1. Read the instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part s list and the picture diagrams). Before

More information

PREPARATIONS AND PRECAUTIONS for Disassembly & Reassembly

PREPARATIONS AND PRECAUTIONS for Disassembly & Reassembly Chapter I Engine PREPARATIONS AND PRECAUTIONS for Disassembly & Reassembly Use genuine parts. With regards to the oil, adhesive and sealing agent, also use genuine or recommended one. With regards to gasket,

More information

8. ENGINE REMOVAL/INSTALLATION

8. ENGINE REMOVAL/INSTALLATION 8. ENGINE REMOVAL/INSTALLATION COMPONENT LOCATION 8-2 SERVICE INFORMATION 8-3 ENGINE REMOVAL 8-4 ENGINE INSTALLATION 8-8 8 8-1 ENGINE REMOVAL/INSTALLATION COMPONENT LOCATION 69 N m (7.0 kgf m, 51 lbf ft)

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

C15C C15C. Page 1 of 20

C15C C15C. Page 1 of 20 2 x Lid Front Hinge 1135 8 x M8 Bolt 8 x M8 Washer (3mm Thick) 4 x M6 Large washers 4 x M6 Spring washers 4 x M6 x 40mm Bolts 6 x M6 20mm Bolts 6 x M6 Washers 20 x Screws 2 x Lid mount gas strut bracket

More information

ACD-PRO Install in 2008 EvoX

ACD-PRO Install in 2008 EvoX Turning in a counter clockwise direction, unscrew ift knob ACD-PRO Install in 2008 EvoX Slide back and remove the floor console panel assembly Pull up to remove the center console tray Disconnect the plug

More information

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment

More information

Contents. Section 5: Adjustments Ball Detect Adjustment Transport Band Tension Adjustment

Contents. Section 5: Adjustments Ball Detect Adjustment Transport Band Tension Adjustment Contents Section 5: Adjustments... 5-3 1. Ball Detect Adjustment... 5-3 2. Transport Band Tension Adjustment... 5-5 3. Transport Band Drive Belt Tension Adjustment... 5-7 4. Ball Cushion Adjustment...

More information

Illustrated Parts Manual

Illustrated Parts Manual Illustrated Parts Manual 2 1 10 550 PS EFT Model Number A2011IBO1PETS (Metallic Gray) S H A R E O U R PAS S IO N. TM TABLE OF CONTENTS 2011 ATV 550 PS EFT Metallic Gray (A2011IBO1PETS) FRONT RACK, BODY

More information

D40C HINGE # x Support Plate x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws

D40C HINGE # x Support Plate x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws HINGE # 1017 2 x Support Plate 1018 8 x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws 2 x Lid mount gas strut bracket 1041 2 x Self tap strut mount 1040 1 x Central Lock bracket 1510

More information

Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987

Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987 Timing Chain: Service and Repair Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987 PREPARATION FOR REMOVAL OF TIMING CHAIN 1. REMOVE CYLINDER HEAD 2. REMOVE RADIATOR 3. REMOVE OIL PAN (a) Remove the engine

More information

920 Remote Control Switches

920 Remote Control Switches 920 Remote Control Switches REMOTE CONTROL SWITCHES Service Bulletin This service bulletin for ASCO 920 Remote Control Switches explains how to replace the main s, operator coil, control s, and how to

More information

1 Recommended tools. removing - refitting : timing belt INJECTION ES9J4. PAGE 1 - b1eg1bp0 - removing - refitting : timing belt. - Fig.

1 Recommended tools. removing - refitting : timing belt INJECTION ES9J4. PAGE 1 - b1eg1bp0 - removing - refitting : timing belt. - Fig. PAGE 1 - b1eg1bp0 - removing - refitting timing belt removing - refitting timing belt INJECTION ES9J4 1 Recommended tools - Fig. 1 - [ 1 ] camshaft setting pegs (-).0187 B. - Fig. 2 - PAGE 2 - b1eg1bp0

More information

AJV8 Engine Assembly. AJV8 Engine Assembly

AJV8 Engine Assembly. AJV8 Engine Assembly AJV8 Engine Assembly Contents Cylinder Block Dowels, Plugs and Pipes 2 4 Crankshaft Bearing and Cylinder Bore Dimensions 5 9 Bearing Measuring 6 Engine Dimensions and Codes 6 7 Main Bearing Selection Chart

More information