P2767-INPUT SPEED SENSOR 2 CIRCUIT NO SIGNAL
|
|
- Letitia Gibson
- 5 years ago
- Views:
Transcription
1 - LX - DODGE MAGNUM/CHARGER -.5L V V MPI - HIGH OUTPUT P-INPUT SPEED SENSOR CIRCUIT NO SIGNAL RUN-START F BATT A 5 RELAY- POWER DISTRIBUTION CENTER A F PK/YL FUSE 5A F PK/BK C TEMPERATURE FUSED RELAY OUTPUT INPUT INPUT CONTROL (NAG) SENSOR-P/N SPEED SPEED SENSOR SWITCH SENSOR SENSOR SENSOR SUPPLY GROUND SIGNAL GROUND (N) SIGNAL (N) SIGNAL VOLTAGE C C C 5 C C C Z Z T5 T T T T BK/GY BK/OR DG/OR DG/VT YL/OR YL YL/DB G G TEMPERATURE SENSOR N N CONTROL UNIT (NAG) H L (NAG) CONTROL C (NAG) CONTROL C (NAG) cb For a complete wiring diagram Refer to the Wiring Information Theory of Operation The Input Speed Sensor (N) is one of two hall effect speed sensors that are used by the Transmission Control Module (TCM) to calculate the transmissions turbine speed. Since the turbine speed could not be measured directly, two of the drive elements are measured. Two input speed sensors are required because both elements are not active in all gears.
2 When Monitored: Engine speed greater than 5 RPM with none of the following DTCs present: engine speed, TCM undervoltage, output speed sensor, and/or rear wheel speed DTCs. Also required are all wheel speeds above 5 RPM and no wheel slip detected (signal from the ABS system). Set Condition: If the Input Speed Sensor (N) signal is equal to RPM. Possible Causes (T) SENSOR SUPPLY VOLTAGE CIRCUIT OPEN (T) INPUT SPEED SENSOR (N) SIGNAL CIRCUIT OPEN (T) SPEED SENSOR (N) SIGNAL CIRCUIT SHORT TO ANOTHER CIRCUIT (T) SENSOR GROUND CIRCUIT OPEN (T) SENSOR GROUND CIRCUIT SHORT TO ANOTHER CIRCUIT (T) SPEED SENSOR (N) SIGNAL CIRCUIT SHORT TO GROUND (T) SENSOR GROUND CIRCUIT SHORT TO GROUND INPUT SPEED SENSOR (N) CONTROL MODULE Always perform the NAG Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to - DTC-Based Diagnostics/MODULE, Transmission. CHECK IF DTC IS CURRENT NOTE: The Transmission Control Module stores under Environmental Data the transmission operating conditions when the DTC was set. Before erasure of any DTC, record all information pertaining to the DTC, even if there is more than one DTC stored.. With the scan tool, erase transmission DTCs.. Using the Environmental Data previously recorded, drive the vehicle and try to duplicate the conditions in which the DTC originally set. Did the DTC P reset? Yes Go To No Go To
3 . CHECK THE (T) SENSOR SUPPLY VOLTAGE CIRCUIT FOR AN OPEN. Turn the ignition off to the lock position.. Disconnect the TCM C harness. Disconnect the Electrohydraulic Control Unit Assembly harness NOTE: Check connectors - Clean/repair as necessary.. Measure the resistance of the (T) Sensor Supply Voltage circuit from the TCM C harness connector to the Electrohydraulic Control Unit Assembly harness (NAG) Is the resistance above 5. ohms? H L Yes Repair the (T) Sensor Supply Voltage circuit for an open. Perform NAG VERIFICATION TEST. (Refer to - DTC- No Go To CONTROL C (NAG). CHECK THE (T) INPUT SPEED SENSOR (N) SIGNAL CIRCUIT FOR AN OPEN. Measure the resistance of the (T) Input Speed Sensor (N) Signal circuit from the TCM C harness connector to the Electrohydraulic Control Unit Assembly harness Is the resistance above 5. ohms? Yes Repair the (T) Input Speed Sensor (N) Signal circuit for an open. Perform NAG VERIFICATION TEST. (Refer to - DTC- No Go To (NAG) H L 5 CONTROL C (NAG)
4 . CHECK THE (T) SENSOR GROUND CIRCUIT FOR AN OPEN. Measure the resistance of the (T) Sensor Ground circuit from the TCM C harness connector to the Electrohydraulic Control Unit Assembly harness Is the resistance above 5. ohms? H L Yes Repair the (T) Sensor Ground circuit for an open. Perform NAG VERIFICATION TEST. (Refer to - DTC- No Go To 5 CONTROL C (NAG) (NAG) 5. CHECK THE (T) INPUT SPEED SENSOR (N) SIGNAL CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT(S). Measure the resistance of the (T) Input Speed Sensor (N) Signal circuit to all the other circuits in the Electrohydraulic Control Unit Assembly harness Is the resistance below 5. ohms between the (T) Input Speed Sensor (N) Signal circuit and any other circuit(s) in the Electrohydraulic Control Unit Assembly harness connector? Yes Repair the (T) Input Speed Sensor (N) Signal circuit for a short to another circuit(s). Perform NAG VERIFICATION TEST. (Refer to - DTC- No Go To (NAG)
5 . CHECK THE (T) INPUT SPEED SENSOR (N) SIGNAL CIRCUIT FOR A SHORT TO GROUND. Measure the resistance between ground and the (T) Input Speed Sensor (N) Signal circuit. Is the resistance below 5. ohms? Yes Repair the (T) Input Speed Sensor (N) Signal circuit for a short to ground. Perform NAG VERIFICATION TEST. (Refer to - DTC- (NAG) No Go To H L 5 CONTROL C (NAG). CHECK THE (T) SENSOR GROUND CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT(S). Measure the resistance between the (T) Sensor Ground circuit to all the other circuits in the Electrohydraulic Control Unit Assembly harness Is the resistance below 5. ohms between the (T) Sensor Ground circuit and any other circuit(s) in the Electrohydraulic Control Unit Assembly harness Yes Repair the (T) Sensor Ground circuit for a short to another circuit(s) Perform NAG VERIFICATION TEST. (Refer to - DTC- No Go To (NAG) 5
6 . CHECK THE (T) SENSOR GROUND CIRCUIT FOR A SHORT TO GROUND. Measure the resistance between ground and the (T) Sensor Ground circuit. Is the resistance below 5. ohms? Yes Repair the (T) Sensor Ground circuit for a short to ground. Perform NAG VERIFICATION TEST. (Refer to - DTC- (NAG) No Go To H L CONTROL C (NAG). CHECK THE INPUT SPEED SENSOR (N) SIGNAL. Reconnect the Electrohydraulic Control Unit Assembly harness. Using a Lab Scope, backprobe the (T) Input Speed Sensor (N) Signal circuit at the TCM C harness WARNING: Properly support the vehicle. H L. Raise all drive wheels off the ground.. Start the engine. WARNING: To avoid personal injury or death, keep hands and feet clear of rotating wheels. 5. Place gear selector in drive and increase vehicle speed to engage nd gear. CONTROL C. Compare the scope pattern on the Lab Scope with a typical 5-volt square wave pattern. (NAG) Is the scope pattern comparable to the typical 5-volt square wave signal scope pattern? Yes Using the schematics as a guide, check the Transmission Control Module (TCM) terminals for corrosion, damage, or terminal push out. Pay particular attention to all power and ground circuits. If no problems are found, replace the TCM per the Service Information.
7 (Refer to - Electrical/Electronic Control Modules/MODULE, Transmission Control - Description) Perform NAG VERIFICATION TEST. (Refer to - DTC- No Replace the Input Speed Sensor (N) per the Service Information. (Refer to - Transmission and Transfer Case/Automatic - NAG/UNIT, Electrohydraulic Control - Disassembly) Perform NAG VERIFICATION TEST. (Refer to - DTC-. INTERMITTENT WIRING AND CONNECTORS. The conditions necessary to set this DTC are not present at this time.. Using the schematics as a guide, inspect the wiring and connectors specific to this circuit.. Wiggle the wiring and connectors while checking for any possible open or shorted circuits.. Check for any Service Information Tune-ups or Technical Service Bulletins that may apply. Were there any problems found? Yes Repair as necessary. Perform NAG VERIFICATION TEST. (Refer to - DTC-Based Diagnostics/ MODULE, Transmission No Test Complete.
P0743-TCC SOLENOID CIRCUIT
- XK - JEEP COMMANDER -.L MAGNUM V P-TCC CIRCUIT RUN-START F JUNCTION BLOCK FUSE A ELECTRO RELAY- - - SHIFT TCC -/ -5 SUPPLY VOLTAGE MODULATION HYDRAULIC UNIT (.L/DIESEL) T T T T5 T T T 5 A /LG DG/ C Z
More informationP0743-TCC SOLENOID CIRCUIT
- KA - DODGE NITRO -.L V SOHC P-TCC SOLENOID CIRCUIT SOLENOID SUPPLY VOLTAGE MODULATION PRESSURE - - SHIFT PRESSURE TCC -/-5 C C C 5 C C C C T YL T YL/TN T T T T5 T YL/LG YL/BR YL/LB C T T T T T T5 T YL
More informationP0882-TRANS 12 VOLT SUPPLY RELAY CONTROL CIRCUIT LOW (DIESEL)
6 - DH - RAM / PICKUP -.9L HO CUMMINS TURBO DIESEL P-TRANS VOLT SUPPLY RELAY CIRCUIT LOW (DIESEL) RUN-START F FUSE A OUTPUT ELECTRONICS POWER C C 9 C F T YL/DB T6 YL/OR S6 F C C T YL/DB 6 T T9 T DG DG/TN
More informationP0882-TCM POWER INPUT LOW
- JK - JEEP WRANGLER - L V6 (SMPI) P-TCM POWER INPUT LOW BATTERY BATT A FUSE J 5A POWER DIESEL GAS Z 6 BK Z 4 BK Z 6 BK 5 7A 7 6 ELECTRONICS 6 C C T6 6 T5 YL/OR YL/BR 5 C C T6 6 T5 YL/OR YL/BR S6 T6 T6
More informationP0842-PRIMARY OIL PRESSURE SENSOR CIRCUIT LOW
- PM - DODGE CALIBER -.4L 4 CYL DOHC 6V DUAL V.V.T. P84-PRIMARY OIL CIRCUIT LOW BATT A B(+) ELECTRONICS TOTALLY INTEGRATED POWER 9 C8 T6 S4 T6 C6 T6 - - S T6 T T4 T T DG/TN DG/BK TN/DG DG/WT T6 6 C6 T
More informationhttps://w05.dealerconnect.chrysler.com/service/mds2002/common/jsp/xml.jsp?xmlurl=... P2149-BANK 2 (CYLINDERS 4-6) SHORTED HIGH OR LOW
Page 1 of 10 P2149-BANK 2 (CYLINDERS 4-6) SHORTED HIGH OR LOW Page 2 of 10 For a complete wiring diagram Refer to the Wiring Information. Page 3 of 10 When Monitored: While the engine is running. Set Condition:
More informationP0876-UD PRESSURE SWITCH RATIONALITY
Page 1 of 14 P0876-UD PRESSURE SWITCH RATIONALITY Page 2 of 14 For a complete wiring diagram Refer to Section 8W When Monitored: Continuously with the ignition on and engine running. Set Condition: This
More informationP PRESSURE CONTROL SOLENOID 4 CONTROL CIRCUIT LOW
0 - DP - RAM 00/00 CAB CHASSIS - 6.7L I6 CUMMINS TURBO DIESEL P70-00-PRESSURE CONTROL CONTROL CIRCUIT LOW For a complete wiring diagram, refer to the Wiring Information. 1 MODULE- TRANSMISSION CONTROL
More informationP0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT - BANK 1 SENSOR 1-5.7L/SRT8
07 - LX - DODGE MAGNUM/CHARGER - 5.7L HEMI V8 - MDS P006-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT - BANK SENSOR - 5.7L/SRT8 CAMSHAFT 5 VOLT SUPPLY SENSOR GROUND CMP F856 S06 F856 C00 F856 K900 S0 S F856
More informationU010C-LOST COMMUNICATION WITH TURBOCHARGER/ SUPERCHARGER CONTROL MODULE
7 - DH - RAM 5/5 PICKUP - 6.7L CUMMINS TURBO DIESEL UC-LOST COMMUNICATION WITH TURBOCHARGER/ SUPERCHARGER CONTROL MODULE BATT A FUSE 4 A TOTALLY INTEGRATED POWER C A9 C TURBO TURBO SPEED SPEED SENSOR SENSOR
More informationP0750-LR SOLENOID CIRCUIT
9 - JS - DGE AVENGER -.L CYL DOHC V DUAL V.V.T. P-LR CIRCUIT BATT A B(+) CONTROL OUTPUT ELECTRONICS TOTALLY INTEGRATED POWER C T S T C T C T S T - - UD / T T YL/TN YL/DG T9 DG/TN T9 T T9 T YL/DB DG/WT
More informationP0716-INPUT SPEED SENSOR 1 CIRCUIT PERFORMANCE
Page 1 of 10 P0716-INPUT SPEED SENSOR 1 CIRCUIT PERFORMANCE Circuit Schematic 2007 Dodge Nitro 3.7L Eng SXT Page 2 of 10 Fig 1: Speed Sensor Circuit Schematic Additional Wiring For complete wiring diagrams
More informationDH - RAM 1500/2500 PICKUP - 6.7L CUMMINS TURBO DIESEL
007 - DH - RAM 500/500 PICKUP - 6.7L CUMMINS TURBO DIESEL U004-CAN B BUS (-) CIRCUIT OPEN For a complete wiring diagram, refer to the Wiring Information. When Monitored: With the ignition on and battery
More informationP0760-OD SOLENOID CIRCUIT
- JC - DGE JOURNEY -.5L V6 V MPI - HIGH OUTPUT P6- CIRCUIT BATT A RELAY-PCM MULE- TOTALLY INTEGRATED POWER A FUSE J A 6 C T6 6 C T6 D C5 T6 S T6 6 L/R / /TRS EMCC VFS C LR UD 6 5 T6 T6 T6 T5 T T T T YL/TN
More informationP0750-LR SOLENOID CIRCUIT
6 - HB - DODGE DURANGO - 5.7L HEMI V - MDS P75-LR CIRCUIT BATT A FUSE 5 5A INTEGRATED POWER 5-6 7 C 7 C 9 C4 Z95 T5 BK YL/BK 4 G T C T S T T TO OTHER MODULES /TRS 7 9 7 T5 YL/BK T T T T6 YL/RD T DG T9
More informationC1020-LEFT REAR WHEEL SPEED SENSOR CIRCUIT
9 - MK - JEEP COMPASS/PATRIOT -.L 4 CYL PZEV 6V DUAL V.V.T. C- CIRCUIT OPTION OPTION B LG/DB B4 LG/BK B DG/OR B YL/DB B DG/LB C4 6 5 C B8 B9 B B4 B DG/TN DG/LG LG/DB LG YL/DB B YL B6 WT/DB B7 WT 46 45
More informationP0406-EGR POSITION SENSOR CIRCUIT HIGH
- LX - DODGE MAGNUM/CHARGER -.5L V V MPI - HIGH OUTPUT P-EGR POSITION SENSOR CIRCUIT HIGH F85 Z9 ASSEMBLY- EXHAUST GAS RECIRCULATION (EXCEPT SRT8) S S5.7L/.5L 5.7L F85.7L.5L C Z9 Z9 Z9 F85 K9 DB/DG S S
More informationP0365-CAMSHAFT POSITION SENSOR CIRCUIT-BANK 1 SENSOR 2
8 - JS - DODGE AVENGER -.4L 4 CYL DOHC 6V DUAL V.V.T. P65-CAMSHAFT SENSOR CIRCUIT-BANK SENSOR BATT A FUSE 8 4A TOTALLY INTEGRATED POWER 7 C8 A4 RD/YL C8 FUSE TOTALLY INTEGRATED POWER 6 B4 B B RELAY-ASD/
More informationC140C- TRANSFER CASE MOTOR CONTROL CIRCUIT HIGH
Page 1 of 13 C140C- TRANSFER CASE MOTOR CONTROL CIRCUIT HIGH Page 2 of 13 For a complete wiring diagram Refer to Section 8W When Monitored: Ignition on. Battery voltage between 9 and 16 volts. Set Condition:
More informationZoom and Print Options
Vehicle» A L L Diagnostic Trouble Codes ( DTC )» Testing and Inspection» P Code Charts» P0707» CVT Automatic Transaxle P0707-TRANSMISSION RANGE SENSOR CIRCUIT LOW http://repair.alldata.com/alldata/article/display.action?componentid=3926&itypeid=423&nonstandardid=1733324&vehicleid=42661&windowname=m
More informationP0750-LR SOLENOID CIRCUIT
2008 Dodge Pickup 4.7L Eng R1500 P0750-LR SOLENOID CIRCUIT Circuit Schematic Fig 1: Transmission Solenoid/TRS Assembly Circuit Schematic Courtesy of CHRYSLER LLC Additional Wiring For complete wiring diagrams
More informationP245C REQUESTED INFORMATION P245C EGR COOLER BYPASS CONTROL CIRCUIT LOW RAM Pickup 6.7L Eng /12/2014 Printer Friendly View
P245C 2012 RAM Pickup 6.7L Eng 2500 REQUESTED INFORMATION P245C EGR COOLER BYPASS CONTROL CIRCUIT LOW http://www1.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=true&ymms=false&classname=
More informationP2017-INTAKE MANIFOLD RUNNER POSITION SENSOR CIRCUIT HIGH
7 - PM - DODGE CALIBER -.4L 4 CYL DOHC 6V DUAL V.V.T. P7-INTAKE RUNNER POSITION SENSOR CIRCUIT HIGH S6 S K9 DB/DG K87 BR/LG 4 6 SENSOR VOLT GROUND SUPPLY GROUND SIGNAL CONTROL Z96 6 BK K6 YL/DB K6 BR/VT
More informationP144F REQUESTED INFORMATION P144F EGR COOLER BYPASS STATUS LINE CIRCUIT HIGH RAM Pickup 6.7L Eng /12/2014 Printer Friendly View
P144F 2012 RAM Pickup 6.7L Eng 2500 REQUESTED INFORMATION P144F EGR COOLER BYPASS STATUS LINE CIRCUIT HIGH http://www1.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=true&ymms=false&classname=
More informationP0463-FUEL LEVEL SENSOR 1 CIRCUIT HIGH
- LX - DODGE CHARGER -.7L V8 HEMI MDS V.V.T. (EZH) P46- SENSOR CIRCUIT HIGH BATT A CLUSTER FUSE 6 POWER DISTRIBUTION CENTER SIGNAL C SIGNAL GROUND C 6 C 6 A A9 6 RD/DG N DB/GY N4 DB/WT Z BK RELAY- 4 C
More informationP2016-INTAKE MANIFOLD RUNNER POSITION SENSOR CIRCUIT LOW
8 - MK - JEEP COMPASS/PATRIOT -.4L 4 CYL DOHC V DUAL V.V.T. P-INTAKE RUNNER POSITION SENSOR CIRCUIT LOW MFV CONTROL MFV SIGNAL VOLT SUPPLY SENSOR GROUND CONTROL 7 C 84 C 4 C 8 C K K K87 K9 BR/VT YL/DB
More informationP TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN
Page 1 of 8 P0045 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN Page 2 of 8 Page 3 of 8 For a complete wiring diagram Refer to Section 8W When Monitored: With the ignition on and the Boost Pressure Servo Motor
More informationP0102-MASS AIR FLOW SENSOR "A" CIRCUIT LOW
7 - D - RAM 5 PICKUP - 6.7L CUMMINS TURBO DIESEL P- SENSOR "A" CIRCUIT LOW BATT A FUSE 7 5A TOTALLY INTEGRATED C A8 8 RD/OR S A8 8 RD/OR A8 8 RD/OR FUSED B(+) RELAY RETURN 5 FUSED B(+) RELAY FEED RELAY-
More informationP0688-AUTO SHUTDOWN SENSE CIRCUIT LOW
- DS - RAM 5 PICKUP - 5.7L V HEMI MDS V.V.T. (EZH) P6- SHUTDOWN SENSE CIRCUIT LOW BATT A B(+) ELECTRONICS TOTALLY INTEGRATED POWER 5 SHUT DOWN 6 FUSE M 5A C C5 K5 C C K5 S4 C 4.7L/ C C C.7L 5.7L S S4 BLACK/BLACK
More informationP0777-SECONDARY PRESSURE SOLENOID STUCK ON (LOW PRESSURE)
009 - MK - JEEP COMPASS/PATRIOT -.0L 4 CYL DOHC 6V DUAL V.V.T. P0777-SECONDARY STUCK ON (LOW ) / LINE SECONDARY ON/OFF 3 4 T0 DG/LB T9 T9 T60 YL/DB YL/LB YL/GY C C 3 C 4 C LINE SECONDARY ON/OFF MODULE-
More informationMK - JEEP COMPASS/PATRIOT - 2.4L 4 CYL DOHC 16V DUAL V.V.T.
9 - MK - JEEP COMPASS/PATRIOT -.4L 4 CYL DOHC 6V DUAL V.V.T. C6-ABS PUMP MOTOR SUPPLY LOW VOLTAGE BATT A A (TIPM) FUSE 5 7 C TIPM A9 RD/DB FUSED B(+) (PUMP) ANTI-LOCK GROUND 6 47 GROUND Z99 BK/WT Z99 BK/WT
More informationGAS P0344-CAMSHAFT POSITION SENSOR INTERMITTENT
2007 Chrysler Truck PT Cruiser L4-2.4L VIN X Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Testing and Inspection > P Code Charts > P0344 GAS P0344-CAMSHAFT POSITION SENSOR INTERMITTENT https://my.alldata.com/repair/#/repair/article/55125/component/3926/itype/423/nonstandard/1175627
More informationP2454-DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT LOW
- WK - JEEP GRAND CHEROKEE -.L V TURBO DIESEL P44-DIESEL PARTICULATE FILTER CIRCUIT LOW. GAS F88 GY/YL K94 OR K GY/BK K K9 K4 BR/DG BK/DB BR/LG 8 C GAS VOLT SUPPLY 9 C GAS GROUND 8 C GAS SIGNAL C SIGNAL
More informationP0344-CAMSHAFT POSITION SENSOR INTERMITTENT
- WK - JEEP GRAND CHEROKEE -.7L MAGNUM V6 P44- SENSOR INTERMITTENT S4 S4 S9 EXCEPT 6.L 6.L F856 YL/PK K9 DB/DG F855 PK/YL F855 8 K9 PK/YL DB/DG CRANKSHAFT 5.7/6.L.7L.7L 5.7L/6.L F856 YL/PK K44 GY/DB K44
More informationPage 1 of 6 1Search P063D 2008 Dodge Pickup 6.7L Eng R2500 P063D-GENERATOR VOLTAGE SENSE HIGH Page 2 of 6 Circuit Schematic Fig 1: Generator Circuit Schematic Courtesy of CHRYSLER LLC Additional Wiring
More informationP O2 SENSOR 1/1 HEATER CIRCUIT
Page 1 of 8 P0030 - O2 SENSOR 1/1 HEATER CIRCUIT Page 2 of 8 For a complete wiring diagram Refer to Section 8W Page 3 of 8 When Monitored: With the ignition on and the Oxygen Sensor Heater command on.
More informationP0073-AMBIENT AIR TEMPERATURE SENSOR CIRCUIT HIGH
8 - JK - JEEP WRANGLER -.8L V6 (SMPI) P7- SENSOR CIRCUIT HIGH BATT A AAT RETURN AAT SIGNAL B(+) BUS (+) BUS (-) ELECTRONICS POWER 4 C4 5 C4 6 C 5 C S S G9 8 VT/BR G 8 VT/LG C 4 C BUS (+) 5 C BUS (-) POWERTRAIN
More informationU010C-LOST COMMUNICATION WITH TURBOCHARGER/ SUPERCHARGER CONTROL MODULE
2014 - D2 - RAM 3500 PICKUP - 6.7L I6 CUMMINS TURBO DIESEL U010C-LOST COMMUNICATION WITH TURBOCHARGER/ SUPERCHARGER CONTROL MODULE For a complete wiring diagram, refer to the Wiring Information. IGN RELAY-
More informationP0123-THROTTLE POSITION SENSOR 1 CIRCUIT HIGH
- DS - RAM PICKUP -.7L MAGNUM V8 8 - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM), NGC/Diagnosis and Testing P- POSITION SENSOR CIRCUIT HIGH VOLT SUPPLY MODULE- POWERTRAIN CONTROL 9 C F8 PK/YL
More informationP0222-THROTTLE POSITION SENSOR 2 CIRCUIT LOW
- RT - DODGE CARAVAN -.L V V.V.T. P- POSITION SENSOR CIRCUIT LOW 5 VOLT SUPPLY CONTROL 5 VOLT SUPPLY 5 VOLT SUPPLY APPS SENSOR APPS APPS SENSOR APPS SENSOR- ACCELERATOR PEDAL POSITION 9 C 5 K855 K85 K7
More informationP0706-TRANSMISSION RANGE SENSOR RATIONALITY
Page 1 of 7 28 - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM), 545RFE/Diagnosis and Testing P0706-TRANSMISSION RANGE SENSOR RATIONALITY Special Tools: Click to display a list of tools used in
More informationB1EB1-1B-FRONT LEFT SEAT HEATER SENSOR - CIRCUIT RESISTANCE ABOVE THRESHOLD
- RT - DODGE CARAAN -.6L 6..T. 8 - DTC-Based Diagnostics/MODULE, Heated Seat (HSM)/Diagnosis and Testing BEB-B-FRONT HEATER SENSOR - CIRCUIT RESISTANCE ABOE THRESHOLD SENSOR RETURN FRONT TEMP SENSE DRIER
More informationHYDRAULIC PRESSURE SWITCH CIRCUIT
Symptom: P1726-UD HYDRAULIC PRESSURE SWITCH CIRCUIT When Monitored and Set Condition: P1726-UD HYDRAULIC PRESSURE SWITCH CIRCUIT When Monitored: In any forward gear with engine speed above 1000 RPM shortly
More informationTRANSMISSION - NGC. Symptom: P0706-CHECK SHIFTER SIGNAL. When Monitored and Set Condition:
Symptom: P0706-CHECK SHIFTER SIGNAL When Monitored and Set Condition: P0706-CHECK SHIFTER SIGNAL When Monitored: Continuously with the ignition on. Set Condition: After 3 occurrences in one ignition cycle
More informationP0014-BANK 1 CAMSHAFT 2 POSITION TARGET PERFORMANCE
08 - PM - DODGE CALIBER -.4L 4 CYL DOHC 6V DUAL V.V.T. P004-BANK CAMSHAFT POSITION TARGET PERFORMANCE MODULE- CMP / CKP CMP / CMP / CONTROL CMP / CONTROL POWERTRAIN CONTROL 8 C 58 C 4 C 79 C 8 C 57 C 4
More informationU1109-LOST COMMUNICATION WITH LIN STEERING WHEEL CONTROLS
8 - KA - DODGE NITRO -.7L MAGNUM U9-LOST COMMUNICATION WITH LIN STEERING WHEEL CONTROLS BATT A FUSE M 5A MODULE- TOTALLY INTEGRATED POWER 9 C A99 8 9 C LIN BUS C CLUSTER A99 8 D5 WT/DG S5 S9 A99 8 D5 WT/DG
More informationB1D7B SEAT HORIZONTAL MOTOR CONTROL CIRCUIT PERFORMANCE
Page 1 of 8 B1D7B SEAT HORIZONTAL MOTOR CONTROL CIRCUIT PERFORMANCE Page 2 of 8 For a complete wiring diagram Refer to Section 8W. Page 3 of 8 When Monitored: Whenever the seat motor is activated. Set
More informationP0365-CAMSHAFT POSITION SENSOR CIRCUIT - BANK 1 SENSOR 2
3 - JC - DODGE JOURNEY - 2.4L 4 CYL DOHC 6V DUAL V.V.T. P0365-CAMSHAFT POSITION CIRCUIT - BANK 2 MODULE- CMP /2 CMP / CKP CKP CMP / CMP /2 POWERTRAIN 85 C2 22 C 67 C2 87 C2 62 C2 66 C2 88 C2 86 C2 67 C2
More informationPRESSURE SWITCH SENSE CIRCUIT
Symptom: P0876-UD PRESSURE SWITCH SENSE CIRCUIT When Monitored and Set Condition: P0876-UD PRESSURE SWITCH SENSE CIRCUIT When Monitored: Whenever the engine is running. Set Condition: This DTC is set if
More informationU0171-LOST COMMUNICATION W/UP-FRONT RIGHT SATELLITE ACCELERATION SENSOR
6 9 8 8 - RT - CHRYSLER TOWN AND COUNTRY -.8L 4 CYL TURBO DIESEL U7-LOST COMMUNICATION W/UP- SATELLITE ACCELERATION SENSOR SENSOR SENSOR - SENSOR SENSOR - SENSOR SENSOR R6 R4 BR/LG TN/LG LHD RHD - N C
More informationB1C29 LEFT SIDE SEAT THORAX S... B1C29 LEFT SIDE SEAT THORAX SQUIB 1 OPEN. 6/14/2016 Direct Hit Search
B1C29 LEFT SIDE SEAT THORAX S... B1C29 LEFT SIDE SEAT THORAX SQUIB 1 OPEN http://dh.identifix.com/searchfixes/index?roid=136882799&vid=2377948&vsm=1&locationid=2#kw=b1c2d+b1c29&soption=1&vetid=1&stmode=1&p
More informationP2000-NOX ABSORBER EFFICIENCY BELOW THRESHOLD
- D - RAM 5 PICKUP - 6.7L CUMMINS TURBO DIESEL P-NOX ABSORBER EFFICIENCY BELOW THRESHOLD For a complete wiring diagram, refer to the Wiring Information. Theory of Operation The engine aftertreatment system
More informationD2 - RAM 3500 PICKUP - 6.7L CUMMINS TURBO DIESEL
0 - D - RAM 00 PICKUP -.7L CUMMINS TURBO DIESEL PB-O SENSOR / CELL CIRCUIT OPEN BATT A0 B(+) ELECTRONICS TOTALLY INTEGRATED POWER FUSED IGNITION SWITCH OUTPUT (RUN-START) PORT LOW PORT HIGH POWER 7 C 7
More informationP0046-TURBOCHARGER BOOST CONTROL CIRCUIT PERFORMANCE
0 - D - RAM 500 PICKUP - 6.7L I6 CUMMINS TURBO DIESEL P006-TURBOCHARGER BOOST CONTROL CIRCUIT PERFORMANCE For a complete wiring diagram, refer to the Wiring Information. 80786 K69 VT/BK - ELECTRONIC TURBO
More informationHYDRAULIC PRESSURE SWITCH CIRCUIT
Symptom: P1787-OD HYDRAULIC PRESSURE SWITCH CIRCUIT When Monitored and Set Condition: P1787-OD HYDRAULIC PRESSURE SWITCH CIRCUIT When Monitored: In any forward gear with engine speed above 1000 RPM shortly
More information6T30/6T40/6T45 - AUTOMATIC TRANSMISSION
2010 GMC Truck Terrain AWD L4-2.4L Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Testing and Inspection > P Code Charts > P0717 6T30/6T40/6T45 - AUTOMATIC TRANSMISSION DTC P0716 or P0717 Diagnostic
More informationP0404-EGR Position Sensor Performance
Page 1 of 7 Your Current Vehicle: 2008 Dodge Ram 1500 P0404-EGR Position Sensor Performance P0404-EGR POSITION SENSOR PERFORMANCE For a complete wiring diagram Refer to the Wiring Information. Theory of
More informationP0401-EGR SYSTEM PERFORMANCE
P0401-EGR SYSTEM PERFORMANCE P0401-EGR SYSTEM PERFORMANCE http://dh.identifix.com/searchfixes/index?roid=176514061&vid=2189101&vsm=2&locationid=2#kw=p0401&soption=1&vetid=8&stmode=1&p 1/6 For a complete
More informationSELF-DIAGNOSTIC TESTS
Page 1 of 10 1997 Chrysler Sebring 2.5L Eng JX SELF-DIAGNOSTIC TESTS NOTE: When using diagnostic tests, DO NOT skip any steps or incorrect diagnosis may result. Ensure battery is fully charged. in appropriate
More informationC147B-FRONT AXLE DISCONNECT SENSOR CIRCUIT PERFORMANCE
- D - RM 00 PICKUP - 6.7L I6 CUMMINS TURBO DIESEL C7B- DISCONNECT SENSOR CIRCUIT PERFORMNCE For a complete wiring diagram, refer to the Wiring Information. 0 0 87 87 FUSE 77 0 RELY- RUN/ STRT FUSE 0 SSEMBLY-
More informationP219B-BANK 2 AIR-FUEL RATIO IMBALANCE
- LC - DODGE CHALLENGER - 6.L V8 SRT HEMI MDS P9B-BANK AIR-FUEL RATIO IMBALANCE For a complete wiring diagram, refer to the Wiring Information. BATTERY A0 0 87 87A RELAY- RUN/ START ASSEMBLY- POWER DISTRIBUTION
More information1 of 14 9/4/2016 4:05 PM
1 of 14 9/4/2016 4:05 PM P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION P0068-Manifold Pressure/Throttle Position Correlation Theory of Operation This DTC sets when an unexpected high intake manifold
More informationPage 1 of 6 2007 Chevrolet Tahoe 5.3L Eng 1Search Print Date: P0036 DTC P0030, P0036, P0053, P0054, P0135, Or P0141 DTC Descriptors DTC P0030 HO2S Heater Control Circuit Bank 1 Sensor 1 DTC P0036 HO2S
More informationB1C2D RIGHT SIDE SEAT THORAX... B1C2D RIGHT SIDE SEAT THORAX SQUIB 1 OPEN. 6/14/2016 Direct Hit Search
B1C2D RIGHT SIDE SEAT THORAX... B1C2D RIGHT SIDE SEAT THORAX SQUIB 1 OPEN http://dh.identifix.com/searchfixes/index?roid=136882799&vid=2377948&vsm=1&locationid=2#kw=b1c2d+b1c29&soption=1&vetid=1&stmode=1&p
More informationP2098-DOWNSTREAM FUEL TRIM SYSTEM 2 LEAN
- DS - RAM 500 PICKUP -.6L V6 V.V.T. P98-DOWNSTREAM FUEL TRIM SYSTEM LEAN BATTERY A0 0 87 87A RELAY- RUN/ START ASSEMBLY- POWER DISTRIBUTION CENTER FUSE A FUSE 78 0A CONNECTOR- STAR CAN C DASH 8 C CAN
More informationJK - JEEP WRANGLER - 3.6L V6 V.V.T.
0 - JK - JEEP WRANGLER - 3.6L V6 V.V.T. U59-LOST COMMUNICATION WITH AUTOMATIC SWAY BAR SYSTEM (ASBS) MODULE WCM ORC SAS HVAC RADIO ITM CCN AMP HFM ABS ASBS PCM TCM ESM CAN C BUS TIPM/CGW CAN INTERIOR BUS
More informationP0088-FUEL RAIL PRESSURE TOO HIGH
2008 - KA - DODGE NITRO - 2.8L 4 CYL TURBO DIESEL 28 - DTC-Based Diagnostics/MODULE, Engine Control (ECM)/Diagnosis and Testing P0088- RAIL TOO HIGH BATT A0 30 RELAY- AUTO SHUT DOWN MODULE- TOTALLY INTEGRATED
More informationP0018-CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR 1
12 - JK - JEEP WRANGLER - 3.6L V6 V.V.T. P0018-CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR 1 For a complete wiring diagram, refer to the Wiring Information. F856 PK/YL F856 PK/YL
More informationCVT RE0F09B TCM P1701 TCM. Description
2012 Nissan-Datsun Altima L4-2.5L (QR25DE) Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Testing and Inspection > P Code Charts > P1701 CVT RE0F09B TCM P1701 TCM Description When the power supply to
More informationP2314-IGNITION COIL 5 SECONDARY CIRCUIT - INSUFFICIENT IONIZATION - 5.7L/SRT8
- LC - DODGE CHALLENGER - 5.7L V8 HEMI MDS V.V.T. (EZH) P4-IGNITION COIL 5 SECONDARY CIRCUIT - INSUFFICIENT IONIZATION - 5.7L/SRT8 S9 IGNITION IGNITION 4 IGNITION 6 K7 DB/TN K5 DB/GY K DB/OR 9 C C COIL
More informationB RIGHT SIDE SEAT DEPLOYMENT SQUIB 1 - CIRCUIT OPEN
05 - UF - CHRYSLER 00 -.4L I4 MULTIAIR B008-3- DEPLOYMENT - CIRCUIT OPEN For a complete wiring diagram, refer to the Wiring Information. - - - SAB REAR R7 LG/GY R5 LB/VT R8 GY/LG R6 VT/LB R4 DB/GY R47
More informationP0113-INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT HIGH
- DS - RAM 5 PICKUP - 4.7L MAGNUM V - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM), NGC/Diagnosis and Testing P- SENSOR CIRCUIT HIGH AAT SENSOR GROUND BUS (+) BUS (-) ELECTRONICS POWER 4 C4 5
More informationPage 1 of 5 Pinpoint Test M: DTCs B1407:11, B1407:12, B1407:13 and B1407:1A Diagnostic Overview Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
More information1 of 6 3/7/2013 9:56 AM 2002 Chevrolet TrailBlazer - 4WD Bravada, Envoy, TrailBlazer VIN S/T Service Manual DTC P1481 Circuit Description The powertrain control module (PCM) uses the cooling fan speed
More informationDTC P0128: THERMOSTAT RATIONALITY
Page 1 of 5 2003 Dodge Neon 2.0L Eng SE DTC P0128: THERMOSTAT RATIONALITY WARNING: When the engine is operating, do not stand in a direct line with the fan. Do not put your hands near the pulleys, belts
More informationDTC P0743 sets when the TCM detects an open circuit, a short to power, or a short to ground in the TCC PWM solenoid circuit for 1.5 seconds.
Page 1 of 5 2005 GMC Truck GMC K Sierra - 4WD Sierra, Silverado VIN C/K Service Manual Document ID: 1492351 DTC P0743 Circuit Description The torque converter clutch (TCC) solenoid is a pulse width modulated
More informationP0030, P0036, -- P0135, P0141, P0155, P0161 P0030, P0036, P0050, P0056, P0135, P0141,
Page 1 of 6 2008 Pontiac G8 DTC P0030, P0036, P0053, P0054, P0135, or P0141 Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy
More informationPage 1 of 6 Pinpoint Test P: DTCs B1414:11, B1414:93, B1419:11 and B1419:93 Diagnostic Overview Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
More informationC1219 C1219-STEERING ANGLE SENSOR ERRATIC PERFORMANCE RAM Pickup 6.7L Eng Search. 7/13/2015 Printer Friendly View
2012 RAM Pickup 6.7L Eng 2500 1Search C1219 C1219-STEERING ANGLE SENSOR ERRATIC PERFORMANCE http://www2.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=true&ymms=false&classname=&hideoptions=false
More informationRefer to Wiring Diagrams Cell 46, Supplemental Restraint System for schematic and connector information.
Page 1 of 12 Pinpoint Test AG: DTCs B0061:11, B0061:12, B0061:13 and B0061:1C Diagnostic Overview Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
More informationSized for Print B1C29-LEFT SIDE SEAT THORAX SQUIB 1 OPEN. For a complete wiring diagram refer to the Wiring Information See: Diagrams\Electrical.
B1C29-LEFT SIDE SEAT THORAX SQUIB 1 OPEN For a complete wiring diagram refer to the Wiring Information See: Diagrams\Electrical. When Monitored: With the ignition on. http://alldatapro.com/alldata/pro~v372401349~c46382~r0~od~n/0/138181779/139756261/139756334/139756336/34853741/96340231/96340248/176614761/1
More informationDJ - RAM 2500 PICKUP - 6.7L I6 CUMMINS TURBO DIESEL
2013 - DJ - RAM 2500 PICKUP - 6.7L I6 CUMMINS TURBO DIESEL 1 P202E-(DIESEL EXHAUST FLUID) REDUCTANT PERFORMANCE MODULE- POWERTRAIN CONTROL SIGNAL 77 K428 DB RETURN 53 C2 K426 DB/LG 1 SIGNAL 2 RETURN -
More informationDTC B0228, B0413, B0423, Or B3779
2007 Chevrolet Silverado 1500 : Heating, Ventilation, & Air Conditioning > HVAC Systems - Manual > Diagnostic Information And Procedures > DTC B0228, B0413, B0423, Or B3779 DTC B0228, B0413, B0423, Or
More informationP0340-CAMSHAFT POSITION SENSOR CIRCUIT - BANK 1 SENSOR 1
11 - RT - CHRYSLER TOWN AND COUNTRY - 3.6L V6 V.V.T. P0340-CAMSHAFT POSITION SENSOR CIRCUIT - BANK 1 SENSOR 1 S109 K856 BR/YL K856 BR/YL 2 SENSOR CAMSHAFT POSITION 2 SENSOR CAMSHAFT POSITION 2 1 4 3 3
More informationP3449-MDS SOLENOID 7 CIRCUIT
8 - HG - CHRYSLER ASPEN - 5.7L HEMI V8 - P449- ENOID 7 CIRCUIT CONTROL CONTROL NO. CONTROL NO. 4 CONTROL NO. 6 CONTROL NO. 7 6 C 8 C 6 C 5 C K45 K454 K45 K45 BR/OR P C8 BR/LB M C8 K45 K454 BR/OR 4 C K45
More informationPOWERTRAIN CONTROL MODULE (PCM) - NGC
2011 Dodge or Ram Truck Grand Caravan V6-3.6L Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Testing and Inspection > P Code Charts > P0128 POWERTRAIN CONTROL MODULE (PCM) - NGC P0128-THERMOSTAT RATIONALITY
More informationDocument ID# Chevrolet Chevy Suburban - 4WD
Page 1 of 8 Document ID# 757392 2003 Chevrolet Chevy Suburban - 4WD Print DTC C0455 Circuit Description The steering wheel position sensor (SWPS) provides one analog signal and 3 digital
More information1 of 8 9/11/2015 3:59 PM
1 of 8 9/11/2015 3:59 PM P013C-O2 SENSOR 2/2 SLOW RESPONSE - RICH TO LEAN For complete wiring diagrams refer to Diagrams/Electrical. - When Monitored: With the engine running, vehicle speed between 32
More informationNo signal from the CMP sensor for 3 seconds with the PCM receiving an engine start signal.
DTC P0340 Circuit Description The DTC P0340 Camshaft Position (CMP) Sensor Circuit diagnostic monitors the output of the CMP sensor. The CMP sensor is located in the distributor and consists of a signal
More informationD2 - RAM 3500 PICKUP - 6.7L CUMMINS TURBO DIESEL
0 - D - RAM 00 PICKUP -.7L CUMMINS TURBO DIESEL PA-O SENSOR / AND / OXYGEN CONCENTRATION MISMATCH BATT A0 B(+) ELECTRONICS TOTALLY INTEGRATED POWER FUSED IGNITION SWITCH OUTPUT (RUN-START) PORT LOW PORT
More informationDRIVEABILITY. Symptom: P0340-NO CAM SIGNAL AT PCM. When Monitored and Set Condition:
Symptom: P0340-NO CAM SIGNAL AT PCM When Monitored and Set Condition: P0340-NO CAM SIGNAL AT PCM When Monitored: Ignition on. Set Condition: At least 5 seconds have elapsed with crankshaft position sensor
More informationDTC P Shift Solenoid Circuit Electrical
1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Circuit Description The 1-2 Shift Solenoid Valve (1-2 SS Valve) controls the fluid flow acting on the 1-2 and 3-4 shift valve. The
More informationPinpoint Tests OSC Equipped Vehicle
SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 11/19/2008 Pinpoint Tests OSC Equipped Vehicle Special Tool(s) 73 III
More informationP0441-EVAP PURGE SYSTEM PERFO... P0441-EVAP PURGE SYSTEM PERFORMANCE
P0441-EVAP PURGE SYSTEM PERFO... P0441-EVAP PURGE SYSTEM PERFORMANCE For a complete wiring diagram, refer to the Wiring Information. Theory of Operation EVAP SYSTEM COMPONENTS CALLOUT DESCRIPTION 1 Filter
More informationAIR CONDITIONING BLOWER CONTROL MODULE/BLOWER RESISTOR TEST G - BLOWER MOTOR OPERATES AT HIGH SPEED AT ALL SPEED SETTINGS
1996 Ford Taurus 3.0L Eng LX AIR CONDITIONING BLOWER CONTROL MODULE/BLOWER RESISTOR TEST G - BLOWER MOTOR OPERATES AT HIGH SPEED AT ALL SPEED SETTINGS 1. Check Blower Operation Disconnect RCC module harness
More informationTechnical Service Bulletin
Subject Technical Service Bulletin DTC P1330 DIAGNOSTIC INFORMATION Group Number Date Model FUEL SYSTEM 10-FL-008 APRIL, 2010 EF SONATA, SM SANTA FE, XG 300/350 [X] PARTS MANAGER [X] TECHNICIAN CIRCULATE
More informationP0430-CATALYST EFFICIENCY (BANK 2)
- XK - JEEP COMMANDER -.7L MAGNUM V6 P4-CATALYST EFFICIENCY (BANK ) MODULE- POWERTRAIN CONTROL O / HEATER CONTROL O / SIGNAL O RETURN (DOWNSTREAM) O / HEATER CONTROL O / SIGNAL O RETURN (UPSTREAM) C C
More informationDTC U : Lost Communication With Anti-Lock Brake System (ABS) Control Module
Page 1 of 6 DTC U0100-U0299 Diagnostic Instructions 2008 Pontiac G8 G8 Service Manual Document ID: 1874258 Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review
More informationDTC P0351, P0352, P0353, P0354, P0355, P0356, P0357, or P0358
DTC Descriptor DTC P0351 Ignition coil 1 control circuit DTC P0352 Ignition coil 2 control circuit DTC P0353 Ignition coil 3 control circuit DTC P0354 Ignition coil 4 control circuit DTC P0355 Ignition
More informationP013A-O2 SENSOR 1/2 SLOW RESPONSE - RICH TO LEAN
Page 1 of 5 P013A-O2 SENSOR 1/2 SLOW RESPONSE - RICH TO LEAN Page 2 of 5 For a complete wiring diagram Refer to the Wiring Information. Page 3 of 5 When Monitored: With the engine running, VSS above 96
More information