Catalogue. Fuel dispensing, storage tank, AdBlue and lubrication equipment

Transcription

1 2016 Catalogue Fuel dispensing, storage tank, AdBlue and lubrication equipment

2 PUMPS Pumps & dispensers for diesel, oil, AdBlue, water & multi-fluid transfer. FUEL MANAGEMENT SYSTEMS iesel, AdBlue & oil management and monitoring systems. FLW METERS Mechanical & electronic display flow meters & pulse meters. HSES & REELS elivery & suction hoses, heating oil lines & hose reels. NZZLES Manual & automatic fuel, AdBlue & lube oil nozzles. TANK ALARMS & VERFILL PREVENTIN Tank level & bund alarms & overfill prevention devices. TANK & RUM GAUGES Mechanical, electronic & sight level gauges for storage tanks. FILTERS & E-AERATRS Fuel filters, filtration units, fuel conditioners & de-aerators. FILL PINT & VENT EQUIPMENT Tank filler caps, fill point equipment, vent caps & cowls. VALVES Safety, fire, check, foot & isolation valves & IBC/drum valves. HSE & PIPE FITTINGS Hose tails & swivels, hose couplings, pipe fittings & IBC/drum fittings. WASTE IL, SPILL, TLS & SEALANTS Waste oil extractors, spill absorbents & engineering tools. Contents \ The 2016 Catalogue 3

3 The 2016 Catalogue / New Products PRUCTS Look out for the logo for products added to our range since our last catalogue PIUSI AIR PERATE IL PUMP PAGE 22 ELITE THREE25 PAGE 26 SELF SERVICE 2.0 FMS RANGE PAGE ATEX K33 PAGE 56 25M HIGH CAPACITY HSE REEL PAGE 75 HUSKY NZZLE RANGE PAGE BUN ALARM PAGE 96 APLL SMART PAGE 103 ENVIRSPILL RANGE PAGE

4 Contents \ Pumps PUMPS IESEL 6-16 IL GREASE 24 ABLUE ATEX MULTI-PURPSE WATER 44 IESEL 6-16 IL GREASE 24 ABLUE ATEX MULTI WATER 44 5

5 Pumps / iesel Pumps Panther 56 Panther 72 E80 E120 72lpm MAX FLW RATE AC PWER See page 42 for carry frames ACCESSRIES Piusi Panther 56/72 Self priming rotary vane pump for general diesel refuelling Sintered steel rotor and acetal resin vanes Cast iron pump body with anti-corrosion paint Mechanical seal for reliability even at low temperatures Integrated bypass valve and 500µ filter, accessible for easy cleaning Induction motor with aluminium casing Protection grade: IP55 Continuous running in open flow Thermal motor overload Available in a range of voltages and flow rates Code escription n/ff Switch Max Flow Rate (lpm) V Hz Amps Watts Ports Fluids Panther v/50Hz o F BSP A Panther v/50Hz o F BSP A Panther v/60Hz o F BSP A Panther v/50Hz F BSP A Panther v/50Hz o F BSP Flanged A Panther v/50Hz F BSP Flanged A 100lpm MAX FLW RATE AC PWER See page 42 for carry frames ACCESSRIES IESEL IESEL Piusi E80/120 Powerful, self priming rotary vane pump for higher flow diesel refuelling Sintered steel rotor and acetal resin vanes Cast iron pump body with anti-corrosion paint Integrated bypass valve and Viton lip seal Induction motor with aluminium casing and anchoring brackets Protection grade: IP55 Continuous running in open flow Thermal motor overload Available in a range of voltages and flow rates Code escription n/ff Switch Max Flow Rate (lpm) V Hz Amps Watts Ports Fluids E80 230v/50Hz o F BSP Flanged A E80 400v/50Hz F BSP Flanged A E v/50Hz o F BSP Flanged A 32700A E v/50Hz/60Hz o / F BSP Flanged A E v/50Hz F BSP Flanged A 6

6 iesel Pumps \ Pumps IESEL Piusi BP3000 Low voltage rotary vane pump for mobile diesel refuelling Sintered steel rotor and acetal resin vanes Cast iron pump body with anti-corrosion paint Integrated bypass valve and NBR lip seal irect current brush motor with permanent magnet stator Pump attachment support bracket Protection grade: IP55 Available with vertical or horizontal push fit or BSP inlet/outlets IESEL Piusi BP3000 Carry & Battery Kit Carry Pump BP3000 diesel pump available as a carry handle kit for mobile refuelling Terminal box with on/off switch & 2m cable & clips. 4m options also available on request. Battery Kit BP3000 Carry pump as part of a portable, ready to dispense kit Manual Self 2000 nozzle & 4m open ended hose, to be cut down into delivery & suction Extra hose tail for nozzle connection, basket filter & jubilee clips Point of display presentation box 50lpm MAX FLW RATE C PWER See page 144 for connection options ACCESSRIES 50lpm MAX FLW RATE C PWER BP3000 Vertical BP3000 Horizontal Code escription Max Flow Rate (lpm) V Amps uty (mins) Ports Fluids BP v Pump nly Vertical ¾ Push Fit A BP v Pump nly Vertical ¾ Push Fit A F BP v Pump nly Horizontal ¾ Push Fit A F BP v Pump nly Horizontal ¾ Push Fit A F BP v Pump nly Horizontal BSP ¾ F BSP A F BP v Pump nly Horizontal BSP ¾ F BSP A R ual Terminal Box c/w 2m Cable & Clips 12/24 R ual Terminal Box c/w 6m Cable & Clips 12/24 See page 41 for drum kit ACCESSRIES BP3000 Carry Vertical Version Battery Kit Horizontal Version Code escription Max Flow Rate (lpm) V Amps Nozzle Hose Ports Fluids 22300C BP v Carry Pump Vertical ¾ Push Fit Hose Tail A 22400C BP v Carry Pump Vertical ¾ Push Fit Hose Tail A BP v Carry Pump Horizontal ¾ BSP Hose Tail A BP v Carry Pump Horizontal ¾ BSP Hose Tail A 22500C BP v Battery Kit Vertical Self 2000 ¾ x 4m ¾ Push Fit Hose Tail A 22600C BP v Battery Kit Vertical Self 2000 ¾ x 4m ¾ Push Fit Hose Tail A BP v Battery Kit Horizontal Self 2000 ¾ x 4m ¾ BSP Hose Tail A BP v Battery Kit Horizontal Self 2000 ¾ x 4m ¾ BSP Hose Tail A 7

7 Pumps / iesel Pumps Bi-Pump Battery Kit 85lpm MAX FLW RATE C PWER Piusi Bi-Pump & Battery Kit Powerful low voltage pump for high flow mobile refuelling Sintered steel rotors and acetal resin vanes Cast iron pump body c/w integrated bypass valve irect current brush motors with permanent magnet stators Pump attachment support bracket Protection grade: IP55 Available as a battery kit with manual nozzle, 4m del & 2m suc hose, NRV & strainer & 2m clips Code escription n/ff Switch Max Flow Rate (lpm) V Amps uty (mins) Ports Fluids 363A0A Bi-Pump nly 12v o F BSP Flanged A 363B0A Bi-Pump nly 24v o F BSP Flanged A Bi-Pump 12v c/w 2m Clips o F BSP Flanged A Bi-Pump 24v c/w 2m Clips o F BSP Flanged A 36302A Bi-Pump 12v c/w 4m Clips o F BSP Flanged A 36304A Bi-Pump 24v c/w 4m Clips o F BSP Flanged A Bi-Pump Battery Kit 12v o F BSP Flanged A Bi-Pump Battery Kit 24v o F BSP Flanged A F m Cable & Clips No Fuse Piusibox Pro Version Contents 45lpm MAX FLW RATE C PWER IESEL IESEL Piusibox BP3000 diesel pump as a portable pumping solution in a handy & compact carry box Manual Self 2000 nozzle & open ended hose to be cut down into delivery & suction Locking vantage foot valve & strainer to prevent leakage Terminal box with on/off switch & 4m cable & clips 10µ particle filter & protective gloves (Pro models only) Ideal for refuelling in heavy duty environments thanks to its protective box preventing contamination e.g. construction sites & agriculture Code escription Max Flow Rate (lpm) V Amps Nozzle Hose Filter Fluids F Piusibox 12v Basic Self 2000 ¾ x 4m A F Piusibox 12v Pro Self 2000 ¾ x 6m 10µ A F Piusibox 24v Basic Self 2000 ¾ x 4m A F Piusibox 24v Pro Self 2000 ¾ x 6m 10µ A F Spare Piusibox Filter A 8

8 iesel Pumps \ Pumps IESEL Piusi Panther C & Battery Kit Self priming, low voltage rotary vane pump for mobile refuelling Sintered steel rotor and acetal resin vanes Cast iron pump body with anti-corrosion paint Mechanical seal for reliability even at low temperatures Integrated bypass valve and 500µ filter, accessible for easy cleaning irect current brush motor with permanent magnet stator Protection grade: IP55 Available as a battery kit with manual nozzle, 4m del & 2m suc hose, NRV & strainer, 2m clips & carry handle 70lpm MAX FLW RATE Code escription n/ff Switch Cable Fuse Max Flow Rate (lpm) V Amps uty (mins) Ports Fluids 34000A Panther C 12v o F BSP A 34100A Panther C 24/12v o 70/35 24/12 25/ F BSP A Panther C 12v c/w 2m Clips o o F BSP A Panther C 24v/12v c/w 2m Clips o o 70/35 24/12 25/ F BSP A Panther C 12v Battery Kit o o F BSP A Panther C 24v/12v Battery Kit o o 70/35 24/12 25/ F BSP A R m Cable & Clips c/w Fuse 12v 12 R m Cable & Clips c/w Fuse 24v 24 R Carry Handle IESEL Piusi Vantage Low voltage vane pump for refuelling onboard plant equipment with the flexibility to be mounted in various positions Monitors its own operation to slow the pump when it gets hot Sintered steel rotor and acetal resin vanes Cast iron pump body with anti-corrosion paint irect current brush motor with permanent magnet stator Pump attachment support bracket Protection grade: IP55 & run dry protection Vertical push fit ports LE for monitoring operation status & stored memory events Electronic control box comes mounted on top of the pump as standard, but can be mounted remotely from the pump if required C PWER 60lpm MAX FLW RATE C PWER See page 144 for push fittings ACCESSRIES Panther C Battery Kit Vantage 60 Electronic Control Box Code escription n/ff Switch Max Flow Rate (lpm) V Amps uty (mins) Ports Fluids F A BP3000 Vantage 60 12v o Self Controlled ¾ Push Fit A F A BP3000 Vantage 60 24v o Self Controlled ¾ Push Fit A 9

9 Pumps / iesel Pumps 90lpm MAX FLW RATE AC/C PWER Piusi Wall Mounted Kit Plated refuelling pump kits ideal for wall or tank mounting Choice of flow rate & voltage depending upon pump model Automatic nozzle, nozzle support, 4m delivery hose & check valve ptional mechanical K33 flow meter Protection grade: IP55 Metal boxed options available instead of plated for extra protection Code escription Max Flow Rate (lpm) V Meter Nozzle Hose Fluids Presentation ST Panther C 12v A K K33 Auto 60 ¾ x 4m A Plated 287P0A ST Panther v A K K33 Auto 60 ¾ x 4m A Plated 365P0A ST Panther v A K K33 Auto 60 ¾ x 4m A Boxed ST E80 230v A K K33 Auto 80 1 x 4m A Plated 36700B ST E80 230v A K K33 Auto 80 1 x 4m A Boxed ST E v A Auto x 4m A Plated ST E v A K K33 Auto x 4m A Plated 36900B ST E v A K K33 Auto x 4m A Boxed 85lpm MAX FLW RATE AC/C PWER IESEL IESEL Piusi Wall Mounted Kit + Filter Plated refuelling pump kits ideal for wall or tank mounting Choice of flow rate & voltage depending upon pump model Automatic nozzle, nozzle support, 6m delivery hose & check valve 10µ or 30µ micron particle & water filter Mechanical K33 flow meter Protection grade: IP55 Code escription Max Flow Rate (lpm) V Meter Nozzle Filter Hose Fluids 386F30CT ST Panther v A K33 30µ K33 Auto 60 30µ ¾ x 6m A 265F30CT ST Panther v A K33 30µ K33 Auto 60 30µ ¾ x 6m A 395F30CT ST E v A K33 30µ K33 Auto µ 1 x 6m A 399F30CT ST Bi-Pump 12v A K33 30µ K33 Auto µ 1 x 6m A 386F10CT ST Panther v A K33 10µ K33 Auto 60 10µ ¾ x 6m A 265F10CT ST Panther v A K33 10µ K33 Auto 60 10µ ¾ x 6m A 395F10CT ST E v A K33 10µ K33 Auto µ 1 x 6m A 399F10CT ST Bi-Pump 12v A K33 10µ K33 Auto µ 1 x 6m A 10

10 iesel Pumps \ Pumps IESEL Piusi Wall Mounted Kit + Pulse Meter Plated refuelling pump kits ideal for wall or tank mounting Choice of flow rate & voltage depending upon pump model Automatic nozzle, nozzle support & 6m delivery hose 10µ or 30µ micron particle & water filter K600 B/3 pulse meter c/w local display & variable pulse output for direct connection to a fuel management system Protection grade: IP55 Piusi ST Box Self-contained pumping system in a sturdy steel locking box for added security and protection Choice of flow rate depending upon pump model Automatic nozzle, nozzle support & 6m delivery hose K33 flow meter & 30µ micron particle & water filter Nozzle holder with pump start/stop (Pro model only) Access 85 that controls access to the pump via electronic keys, has an emergency stop, level sensor & pump timer (Pro model only). Please note: User keys are an optional extra. Protection grade: IP55 85lpm MAX FLW RATE AC/C Code escription Max Flow Rate (lpm) V Meter Nozzle Filter Hose Fluids CTS2054 ST Panther v A K600 B/3 30µ K600 B/3 Auto 60 30µ ¾ x 6m A CTS2055 ST Panther v A K600 B/3 30µ K600 B/3 Auto 60 30µ ¾ x 6m A CTS2056 ST E v A K600 B/3 30µ K600 B/3 Auto µ 1 x 6m A CTS2058 ST Bi-Pump 12v A K600 B/3 30µ K600 B/3 Auto µ 1 x 6m A CTS2059 ST Panther v A K600 B/3 10µ K600 B/3 Auto 60 10µ ¾ x 6m A CTS2060 ST Panther v A K600 B/3 10µ K600 B/3 Auto 60 10µ ¾ x 6m A CTS2061 ST E v A K600 B/3 10µ K600 B/3 Auto µ 1 x 6m A CTS2062 ST Bi-Pump 12v A K600 B/3 10µ K600 B/3 Auto µ 1 x 6m A IESEL PWER 85lpm MAX FLW RATE Code escription Max Flow Rate (lpm) V Meter Nozzle Filter Hose Access 85 Nozzle Switch Fluids F ST Box Basic Panther K33 Auto 60 30µ ¾ x 6m A F ST Box Basic E K33 Auto µ 1" x 6m A F ST Box Pro Panther K33 Auto 60 30µ ¾ x 6m o o A AC PWER See page 49 for Access 85 INFRMATIN See page 64 for K600 B/3 Pulse Meter INFRMATIN Pro Basic 11

11 Pumps / iesel Pumps 90lpm MAX FLW RATE AC/C PWER Piusi Cube Range Compact red boxed fuel dispenser for wall or tank mounting Self priming, acetal resin vane pump c/w sintered steel rotor Mechanical seal & integrated bypass valve Nutating disk mechanical flow meter (Pulse version 10:1-3 wire) Automatic nozzle c/w flexible hose & swivel connections Nozzle holder with pump start/stop lever Cube 56/70 continuous running, Cube 90 30min duty cycle Protection grade: IP55 Code escription n/ff Switch Cable Fuse Max Flow Rate (lpm) V Ports Meter Nozzle Hose Fluids 57500C Cube v o BSP K33 Auto 60 ¾ x 4m A 57516A Cube v + Pulse ut o BSP K44 Auto 60 ¾ x 4m A Cube v o BSP K33 Auto 60 ¾ x 4m A 59100A Cube v o BSP Flanged K33 Auto 60 1 x 4m A 59111A Cube v + Pulse ut o BSP Flanged K44 Auto 60 1 x 4m A Cube C 12v o o BSP K33 Auto 60 ¾ x 4m A Cube C 24/12 o o 70/35 24/12 1 BSP K33 Auto 60 ¾ x 4m A 59200A Cube v o BSP Flanged K44 Auto x 4m A F12708 F12737 Cube Pedestal Black Cube Wall Support Kit 8930 Quick Coupling 1 x 2 90lpm MAX FLW RATE AC PWER IESEL IESEL Piusi Self Service Compact fuel dispenser for high flow private refuelling Self priming vane pump with bypass valve Integrated nutating disk mechanical K44 meter (Pulse version 10:1-3 wire) Automatic nozzle c/w flexible hose & swivel connections Nozzle holder with pump start/stop lever Continuous running Protection grade: IP55 Freestanding or mini versions for tank mounting available ptions with water filter and/or pulse output Code escription n/ff Switch Max Flow Rate (lpm) V Ports Meter Nozzle Hose Filter Fluids 737B00 Self Service 70 Mini o ½ F BSP K44 Auto ¾ x 4m A 737B20 Self Service 70 Mini + Pulse ut o ½ F BSP K44 Auto ¾ x 4m A 73701B Self Service 70 + Filter o ½ F BSP K44 Auto ¾ x 4m 30µ A 740B00 Self Service 100 Mini o ½ F BSP K44 Auto 1 x 4m A 74001B Self Service Filter o ½ F BSP K44 Auto ¾ x 4m 30µ A Self Service Filter + Pulse ut o ½ F BSP K44 Auto ¾ x 4m 30µ A 12

12 iesel Pumps \ Pumps IESEL Piusi Pico Centrifugal pump c/w priming device for dispensing from a drum Universal motor with double-insulated body and in-built switch 4m delivery hose & suction hose with strainer 2 BSP and M 64 x 4 drum connection for direct mounting ptions with K24 flow meter & choice of manual or auto nozzle 2m power cables (230v versions), 3m cable & clips (C versions) Popular refuelling solution in agricultural or work site environments Piusi rum Pump Kit Complete refuelling solution designed for dispensing directly from a drum Mains powered or low voltage depending upon model Automatic nozzle, nozzle holster & 4m delivery hose Telescopic suction down tube Quick coupling for easy drum connection ptional mechanical K33 flow meter Popular refuelling solution in agricultural, workshop or construction site environments 35lpm MAX FLW RATE AC/C PWER Code escription Max Flow Rate (lpm) V Amps Meter Nozzle Fluids F Pico rum Pump 12v M Manual A F Pico rum Pump 12v A Auto 60 A F Pico rum Pump 12v M K K24 Manual A F Pico rum Pump 12v A K K24 Auto 60 A F Pico rum Pump 24v M Manual A F Pico rum Pump 24v A Auto 60 A F Pico rum Pump 24v M K K24 Manual A F Pico rum Pump 24v A K K24 Auto 60 A F Pico rum Pump 230v M Manual A F Pico rum Pump 230v A Auto 60 A F Pico rum Pump 230v M K K24 Manual A F Pico rum Pump 230v A K K24 Auto 60 A IESEL 80lpm MAX FLW RATE AC/C PWER Code escription Max Flow Rate (lpm) V Meter Nozzle Hose Fluids 273P00 Panther v A Auto 60 ¾ x 4m A 274P00 Panther v A K K33 Auto 60 ¾ x 4m A F Panther C 24/12v A K33 70/35 24/12 K33 Auto 60 ¾ x 4m A 22203A Bi-Pump 12v A Auto x 4m A 22207A Bi-Pump 12v A K K33 Auto x 4m A 22208A Bi-Pump 24v A K K33 Auto x 4m A 13

13 Pumps / iesel Pumps IBC Kit Top Suction Kit Bottom Suction Kit 56lpm MAX FLW RATE AC PWER IBC Plated Pump & Suction Kits Pump Kits Plated Panther 56 designed specifically for IBC mounting Automatic nozzle, nozzle support & 4m delivery hose ptional mechanical K33 flow meter Choice of optional bottom or top suction kit depending upon the individual IBC Suction Kits Bottom suction kit - 60 x 6 Buttress to 1 CAM male, 2m suction hose, NRV & Y strainer Top suction kit - 2m x 1 suction hose, NRV & Y strainer Code escription n/ff Switch Max Flow Rate (lpm) V Ports Nozzle el Hose Meter Fluids CTS2017 Panther 56 K33 A IBC Kit o F BSP Auto 60 4m K33 A CTS2038 Panther 56 A IBC Kit o F BSP Auto 60 4m A SUC01 Bottom Suction Kit AF SUC02 Top Suction Kit AF Pitstop 2 x BP3000 included 45lpm MAX FLW RATE C PWER IESEL IESEL Piusi Pitstop 2 x BP3000 diesel pumps in a sturdy dispensing unit with 14m hose reel c/w hose stop & adjustable arms esigned for refuelling in heavy duty environments where access to vehicles may be difficult Cast iron pump body c/w sintered steel rotor & acetal resin vanes Integrated bypass valve 4m cable & clips Sturdy metal supporting structure with safety guards Automatic nozzle with holster and padlock to lock in place 30µ water & particle filter Protection grade: IP55 Code escription n/ff Switch Max Flow Rate (lpm) V Amps Ports Nozzle Hose Fluids F Pitstop 12v o ¾ Hose Tail Auto 60 ¾ x 14m A F Pitstop 24v o ¾ Hose Tail Auto 60 ¾ x 14m A 14

14 iesel Pumps \ Pumps IESEL Piusi ST 200 AC esigned for high flow transfer in heavy duty environments such as construction, quarries and mines 2 x E120 diesel pumps in a sturdy steel frame Cast iron pump body c/w sintered steel rotor & acetal resin vanes Integrated bypass valve & on/off switch Protection grade: IP55 Allows for the easy installation of an optional K700 flow meter Portability kit with handle & wheels available as an option Piusi ST 200 C For high flow transfer in heavy duty environments such as construction, quarries & mines where mains power is unavailable 4 x BP3000 diesel pumps c/w 4m cable & clips & 2 carry handles Cast iron pump body c/w sintered steel rotor & acetal resin vanes Integrated bypass valve & on/off switch Ceramic graphite mechanical seal uty cycle: 20 min on/40 min off Protection grade: IP55 Allows for the easy installation of an optional K700 flow meter 200lpm MAX FLW RATE Code escription n/ff Switch Max Flow Rate (lpm) V Hz Amps Watts Ports Fluids F ST 200 AC o ½ F BSP Flanged A F ST 200 AC Portability Kit IESEL AC PWER 185lpm MAX FLW RATE Code escription n/ff Switch Max Flow Rate (lpm) V Amps Watts Ports Fluids F ST 200 C o ½ F BSP Flanged A IESEL Piusi E300 Self priming electric pump designed for high flow diesel transfer applications Cast iron open impeller Incorporated check valve in the suction port to prevent the siphoning effect & ensure automatic re-priming Protection grade: IP44 Continuous running in open flow C PWER 300lpm MAX FLW RATE AC PWER See page 57 for K700 Flow Meter INFRMATIN See page 57 for K700 Flow Meter INFRMATIN Code escription Max Flow Rate (lpm) V Amps Watts Ports Fluids F Piusi E " BSP A 15

15 Pumps / iesel Pumps 2" Model 500lpm MAX FLW RATE Engine TYPE See page 44 for water versions RELATE PRUCTS IESEL Engine riven iesel Pumps 4 stroke petrol engine driven pump with recoil start For mobile, high flow diesel transfer where mains power is unavailable 1 models plate mounted, 2 models in steel frame Carry facility for portable use Must not be run dry If used with a nozzle, a pressure relief valve or damper valve must be used or warranty will become void Code escription Running Fuel Tank Size (l) Max Flow Rate (lpm) Max Lift (m) Max Head (m) Ports Fluids CTS125E 1 Engine riven Pump UL Petrol Hose Tail AM CTS2500E 2 Engine riven Pump UL Petrol Hose Tail AM CTS125E 1 amper Valve for Portable Use AMI CTS125EP 1 Pressure Relief Valve AMI CTS2500EP 2 Pressure Relief Valve AMI 140lpm MAX FLW RATE Engine TYPE See above table for 1" pressure relief valve RELATE PRUCTS IESEL B3 B30 1" Honda Engine riven iesel Pump Tsurumi pump head powered by a genuine Honda GX25 4 stroke petrol engine c/w hose tails & 1 foot strainer For mobile, high flow diesel & water transfer where mains power is unavailable Steel base with rubber feet and carry facility for portable use Mechanical shaft seal 1hr 30min running time on tank of fuel Best duty point: 25m head Code escription Running Fuel Max Flow Rate (lpm) Max Head (m) Ports Fluids CTS140E 1 Honda Engine riven Pump UL Petrol Hose Tail AI Gear Pump Start-Up Box 50lpm MAX FLW RATE AC PWER IESEL W WATER IL Close Coupled Gear Pump Close coupled gear pump for pumping diesel & thin oils long distances e.g. when tank can t be sited at the dispensing point With a nozzle on the end, it can pump diesel over approx. 200m of 1 horizontal pipe Cast iron pump body on baseplate & ductile iron gears Adjustable bypass & mechanical seal for reliability at low temps Protection grade: IP55 ptional electromechanical panel for direct start-up of pump Code escription Max Flow Rate (lpm) V Hz Watts Ports Fluids CTS2071 Close Coupled Gear Pump 10 bar AF CTS2072 Pump irect Start-Up Box

16 il Pumps \ Pumps IL Piusi Viscomat Vane Electric vane pump for transferring oils & lubricants at higher flow rates Sintered steel rotor, acetal resin vanes & viton lip seal Integrated adjustable bypass valve (only on Viscomat 70) Suitable for continuous running in open flow situations Smooth flow, high suction capacity & low noise level Maximum fluid temperature of +70 c Viscosity up to 500cSt (check oil viscosity at lowest temperature in use) Protection grade: IP55 Available in a range of voltages and flow rates IL Piusi Viscomat Gear Electric gear pump for transferring oils & lubricants at higher flow rates Aluminium body, sintered steel gears & NBR 902 lip seal Integrated adjustable bypass valve & self priming device Suitable for continuous running in open flow situations Smooth flow, high suction capacity & low noise level Maximum fluid temperature of +70 c Viscosity from cSt (check oil viscosity at lowest temperature in use) Protection grade: IP55 Available in a range of voltages and flow rates 50lpm MAX FLW RATE AC PWER See page 175 for viscosity table INFRMATIN 14lpm MAX FLW RATE AC PWER Viscomat Vane 70 Code escription n/ff Switch Max Flow Rate (lpm) V Hz Amps Watts Pressure (bar/psi) Ports Fluids Viscomat 70M 230v o /87 1 F BSP F Viscomat 70M 110v o /87 1 F BSP F Viscomat 70T 400v /87 1 F BSP F 303M00 Viscomat 90M 230v o /72 1 F BSP F Viscomat 90T 400v /78 1 F BSP F See page 175 for viscosity table INFRMATIN Vane Viscomat Gear Code escription n/ff Switch Max Flow Rate (lpm) V Hz Amps Watts Pressure (bar/psi) Ports Fluids Viscomat 200/2M o /174 1 F BSP F Viscomat 200/T /174 1 F BSP F Viscomat 230/3M o /174 1 F BSP F 304T40 Viscomat 230/3T /174 1 F BSP F Viscomat 350/2M o /362 1 F BSP F 304T10 Viscomat 350/2T /362 1 F BSP F Gears 17

17 Pumps / il Pumps Viscomat Flowmat Gears 14lpm MAX FLW RATE AC PWER 4lpm MAX FLW RATE Piusi Viscomat Flowmat Viscomat gear pump with pressure switch & safety valve for oil & lubricant transfer at higher pressures Automatically activates when nozzle opens & switches off at the end of delivery for added convenience Aluminium body, sintered steel gears & NBR 902 lip seal Integrated adjustable bypass valve & self priming device Maximum pressure adjustment device Smooth pulse less flow, high suction capacity & low noise level Maximum fluid temperature of +70 c Viscosity from cSt (check oil viscosity at lowest temperature in use) Protection grade: IP55 Code escription n/ff Switch Max Flow Rate (lpm) V Hz Amps Watts Pressure (bar/psi) Ports Fluids Viscomat Flowmat 200/2 o /87 1 F BSP F Viscomat Flowmat 230/3 o /174 1 F BSP F Viscomat Flowmat 350/2 o /362 1 F BSP F Viscomat Gear Gears See page 175 for viscosity table INFRMATIN C PWER See page 175 for viscosity table INFRMATIN IL IL Piusi Viscomat C 60/1 C gear pump for the transfer of oil & lubricant fluids often from a drum Aluminium body & sintered steel gears Integrated adjustable bypass valve Maximum fluid temperature of +70 c Viscosity from cSt (check oil viscosity at lowest temperature in use) Protection grade: IP55 ptional cable & clips for battery connection Popular solution when mains power or air connection is unaccessible Code escription n/ff Switch Max Flow Rate (lpm) V Amps Pressure (bar/psi) uty (mins) Ports Fluids F Viscomat C 60/1 12v o /70 30 ½ F BSP F F Viscomat C 60/1 24v o /70 30 ½ F BSP F R m Cable Kit 12v/24v R m Cable Kit 12v/24v 18

18 il Pumps \ Pumps IL Piusi Viscomat C 60/2 & 120/1 C gear pump for oil transfer where mains power is unavailable Aluminium body & sintered steel gears Integrated adjustable bypass valve Maximum fluid temperature of +70 c Viscosity from cSt 60/2 / cSt 120/1 (check oil viscosity at lowest temperature in use) Protection grade: IP55 Pressure switch version available for pump auto start/stop ptional cable & clips c/w fuse for battery connection IL Piusi Viscomat Battery Kit Viscomat C 60/2 oil pump as part of a portable, ready to dispense kit Manual Self 3000 nozzle 4m open ended hose to be cut down into delivery & suction Hosetail & strainer for filtering large debris 2m cable & clips for battery connection Suction capacity up to 2m Viscosity from cSt (check oil viscosity at lowest temperature in use) Popular solution when mains power or air connection is unaccessible such as in agricultural and work site environments 10lpm MAX FLW RATE Code escription n/ff Switch Pressure Switch Max Flow Rate (lpm) V Amps Pressure (bar/psi) uty (mins) Ports Fluids F Viscomat C 60/2 12v o /57 30 ¾ F BSP F F Viscomat C 60/2 24v o /57 30 ¾ F BSP F F Viscomat C 120/1 12v o / ½ F BSP F F Viscomat C 120/1 24v o / ½ F BSP F F Viscomat C 120/1 12v PST o / ½ F BSP F F Viscomat C 120/1 24v PST o / ½ F BSP F R m Cable Kit 12v R m Cable Kit 24v R m Cable Kit 12v R m Cable Kit 24v C PWER 10lpm MAX FLW RATE C PWER See page 175 for viscosity table INFRMATIN See page 175 for viscosity table INFRMATIN Code escription n/ff Switch Max Flow Rate (lpm) V Amps Nozzle Hose Fluids F Viscomat Battery il Kit 12v o Self 3000 ¾ x 4m F F Viscomat Battery il Kit 24v o Self 3000 ¾ x 4m F 19

19 Pumps / il Pumps See page 175 for viscosity table INFRMATIN 45lpm MAX FLW RATE AC PWER Piusi Viscomat Wall Mounted Kit Plated oil dispensing pump kits ideal for mounting onto a wall or tank Choice of flow rate depending upon pump model Manual nozzle, nozzle support & 4m delivery hose in ¾ (Viscomat 70) or 1" (Viscomat 90) Choice of mechanical flow meter (Viscomat 70) or digital flow meter (Viscomat 90) Viscosity up to 500cSt (check oil viscosity at lowest temperature in use) Protection grade: IP55 Metal boxed option available instead of standard plated version for extra protection Code escription Max Flow Rate (lpm) V Rotor Meter Nozzle Hose Presentation Fluids ST Viscomat 70 K33 M Vane K33 Self 2000 ¾ x 4m Plated F ST Viscomat 70 K33 M Vane K33 Self 2000 ¾ x 4m Boxed F ST Viscomat 90 K600 M Vane K600 Self x 4m Plated F 26100A Model See page 175 for viscosity table INFRMATIN 25lpm MAX FLW RATE AC PWER IL IL Piusi Viscomat rum Pump Kit Complete oil transfer kit designed for dispensing directly from a drum Viscomat vane or gear pump depending upon model Nozzle, nozzle support & 4m delivery hose Telescopic suction down tube Quick coupling for easy drum connection ptional flow meter (mechanical for Viscomat 70 and digital for Viscomat 200/2) Viscosity up to 500cSt vane type / cSt gear type (check oil viscosity at lowest temperature in use) Popular solution in agricultural, garage or workshop environments Code escription Max Flow Rate (lpm) V Rotor Meter Nozzle Hose Fluids rum Viscomat 70 M Vane Self 3000 ¾ x 4m F rum Viscomat 70 K33 M Vane K33 Self 3000 ¾ x 4m F T rum Viscomat 70 M 110v Vane Self 3000 ¾ x 4m F 26100A rum Viscomat 200/2 M Gear Easyoil ½ x 4m F 26200A rum Viscomat 200/2 K400 M Gear K400 Easyoil ½ x 4m F 20

20 il Pumps \ Pumps IL Piusi Viscotroll Complete mobile kit fixed on a drum trolley for oil transfer in a garage or workshop environment Viscomat vane, AC or C gear pump depending upon model Nozzle, nozzle support, drip collector, delivery & suction hose ptional flow meter Pressure switch models available for pump auto start/stop C models c/w inbuilt battery & charger Viscosity up to 500cSt vane type / cSt gear type (check oil viscosity at lowest temperature in use) IL IBC Plated Pump & Suction Kits Pump Kits Plated Viscomat pump designed specifically for IBC mounting Nozzle, nozzle support & 4m delivery hose Mechanical or digital flow meter (depending on model) Choice of either bottom or top suction kit depending upon the individual IBC Check oil viscosity at lowest temperature in use Suction Kits Bottom suction kit 60 x 6 Buttress to 1 CAM male, 2m suction hose, NRV & ½" Y strainer Top suction kit 2m x 1 suction hose, NRV & Y strainer 25lpm MAX FLW RATE AC/C PWER See page 175 for viscosity table INFRMATIN Code escription Max Flow Rate (lpm) V Rotor Meter Nozzle el Hose Pressure Switch Fluids Viscotroll 200/ Gear Easyoil ½" x 4m F Viscotroll 200/2 K Gear K400 Easyoil ½" x 4m F Viscotroll 200/2 PST Gear Easyoil ½" x 4m o F Viscotroll 200/2 K400 PST Gear K400 Easyoil ½" x 4m o F Viscotroll Vane Self 3000 ¾ x 4m F Viscotroll 70 K Vane K33 Self 3000 ¾ x 4m F CTS Viscotroll 70 K33 110v Vane K33 Self 3000 ¾ x 4m F Viscotroll 120/1 - PST 6 12 Gear Easyoil ½" x 4m o F Viscotroll 120/1 K400 PST 6 12 Gear K400 Easyoil ½" x 4m o F 45lpm MAX FLW RATE Code escription Max Flow Rate (lpm) V Rotor Nozzle el Hose Meter Fluids CTS2018 Viscomat 70 K33 M IBC Vane Self " x 4m K33 F CTS2019 Viscomat 90 K33 M IBC Vane Self " x 4m K33 F CTS2048 Viscomat Flowmat K400 M IBC Gear Easyoil ½ x 4m K400 F SUC01 Bottom Suction Kit FA SUC02 Top Suction Kit FA AC PWER See page 175 for viscosity table INFRMATIN IBC Kit Top Suction Kit Bottom Suction Kit 21

21 Pumps / il Pumps FEATURE 175mm pipe 940mm pipe Accessories... F F mm F mm F mm F mm F F m F/F 1/2 F m M/F 1/2 F "Pro + Silent" oil transfer with the Piusi air operated pump range 6 Kg rum F Kg rum F Code escription Ratio Max Flow Rate (lpm) 21.5lpm MAX FLW RATE Air PWER Suction Pipe Length Piusi Air perated il Pumps New from Piusi is the Pro + Silent air operated oil pump range; part of their growing offering to the oil & lubrication market. The design of these pumps has been specially considered to ensure high performance and durability in garage and workshop environments. There are 3:1 and 5:1 ratio models, both available in stub & long length for mounting to a wall or an oil drum: 3:1 For pumping medium viscosity oils over short/medium distances 5:1 For pumping medium to high viscosity oils over medium/long distances Features :1 & 5.5:1 compression ratio air operated oil transfer pumps Low operating noise & sound proof protective structure limiting noise to 77dB Pneumatic exchanger & three-stage air discharging system ouble effect guarantees enhanced efficiency & reduced air consumption Absence of reciprocating mechanical parts that are subject to wearing ensures long working life Supplied with 2 BSP bung adaptor to ensure stable mounting on oil drums or wall bracket Polyurethane internal seals Available in stub (175mm) & long length (940mm) depending upon the installation requirements Air Pressure (bar) A range of optional accessories are available to go alongside the pumps (see left) Air Consumption (lpm) Air Inlet utlet Fluids F A Piusi 3:1 Air il Pump 175mm 3.5: ¼ F ½ M BSP F F A Piusi 3:1 Air il Pump 940mm 3.5: ¼ F ½ M BSP F F A Piusi 5:1 Air il Pump 175mm 5.5: ¼ F ½ M BSP F F A Piusi 5:1 Air il Pump 940mm 5.5: ¼ F ½ M BSP F IL 22

22 il Pumps \ Pumps IL Piusi Air perated iaphragm Pump Self priming single membrane air operated diaphragm pump with aluminium or polypropylene body Ideal for transferring oil in garage & workshop environments where there is an existing air line NBR diaphragm, NBR balls & NBR 'o'rings (other materials available on request) Can run dry without damage ATEX approved to Zone 2 Max diameter of passing solid 4mm IL Engine riven Waste il Pump Self priming 5.7HP petrol engine driven pump for non-flammable, thick & used oils such as diesel, gas oil, cooking & engine oil For mobile, high flow transfer where mains power is unavailable Steel mounting frame with rubber feet 14 micron teeth clearance for pumping soft solids only Viton seals Temperature rating of +90 C IL IESEL Lubrication Hand Pump Spring operated lubrication hand pump designed for dispensing from a 60ltr drum For topping up engines & gear boxes with lubricant & transmission fluid Nozzle, drain back nozzle holster & UV stabilised hose Rigid suction pipe & 2 BSP drum connection Version with flow meter available 220lpm MAX FLW RATE Code escription Max Flow Rate (lpm) Inlet/utlet Air Inlet Ball Seats Self Priming (m) Max Head (m) Max Air Supply (bar) Fluids F00208A00 MA130 A il Alu 50 ½ F BSP ⅜ F BSP Aluminium FA F00208P10 MA140 A il PP F BSP ⅜ F BSP Polypropylene FA F00208A10 MA180 A il Alu F BSP ⅜ F BSP PPS-V FA F00208A20 MA190 A il Alu ¼ F BSP ½ F BSP PPS-V FA n request we can provide membranes, valls, ball seats & 'o' rings in different materials IESEL B1 B100 Air PWER 85lpm MAX FLW RATE Engine PWER 500ml per stroke MAX FLW RATE 2" M BSP MUNTING Code escription Running Fuel Max Flow Rate (lpm) Suction Height ry (m) Suction Height Wet (m) Ports Fluids CTS1100 Petrol Engine riven il Pump UL Petrol ¼ Hose Barbs FAP Code escription Max Flow Rate (per stroke) Meter Nozzle el Hose Suction Mounting Fluids CTS2014 Lubrication Hand Pump 500ml o UV stabilised hose Rigid downtube 2 M BSP F CTS2015 Lubrication Hand Pump c/w Meter 500ml o o UV stabilised hose Rigid downtube 2 M BSP F ptional meter 23

23 Pumps / Grease Pumps 50:1 RATI Air PWER Air perated Grease Pump 50:1 air operated grease pumps for mobile or fixed installations Supplied with double acting suction tubes Models available to fit 12.5kg, 50kg & 180kg drums Regulate air inlet pressure from 5-8 bar Code escription Ratio Max Air Supply (bar) utlet Air Inlet Air Consumption (lpm) For rum Size Fluids CTS :1 Grease Pump 12.5kg 50:1 8 ¼ M BSP ¼ F BSP kg K CTS :1 Grease Pump 50kg 50:1 8 ¼ M BSP ¼ F BSP kg K CTS :1 Grease Pump 180kg 50:1 8 ¼ M BSP ¼ F BSP kg K 50:1 RATI Air PWER 50:1 RATI Air perated Grease Pump Kit 50:1 air operated grease pump kit 4m delivery hose & grease control nozzle c/w straight swivel rum cover c/w portability handles for a 12.5kg drum 265mm follower plate Code escription Ratio Max Air Supply (bar) utlet Air Inlet Air Consumption (lpm) For rum Size Fluids CTS :1 Grease Pump Kit 50:1 8 ¼ M BSP ¼ F BSP kg K See page 89 for grease control nozzle RELATE PRUCTS Air PWER GR GREASE GR GREASE GR GREASE Mobile Air perated Grease Pump Kit 50:1 air operated grease pump kit c/w 4 wheeled trolley 4m delivery hose & grease control nozzle c/w straight swivel rum cover c/w portability handles for a 12.5kg or 50kg drum Follower plate 265mm (12.5kg) or 370mm (50kg) Code escription Ratio Max Air Supply (bar) utlet Air Inlet Air Consumption (lpm) For rum Size Fluids CTS :1 Mobile Grease Pump Kit 12.5kg 50:1 8 ¼ M BSP ¼ F BSP kg K CTS :1 Mobile Grease Pump Kit 50kg 50:1 8 ¼ M BSP ¼ F BSP kg K 24

24 AdBlue Pumps \ Pumps AB ABLUE Suzzara Blue AC Pump nly Self priming 5 chamber membrane pump with no shaft seal esigned specifically for the transfer of AdBlue Integrated bypass valve 2m cable with UK plug (110v version without) Protection grade: IP55 Version with or without protected on/off switch Uses custom designed o ring sealed plastic fittings uty cycle: 20mins Code escription n/ff Switch Max Flow Rate (lpm) 34lpm MAX FLW RATE AC PWER V Hz Amps Watts Ports Fluids F Suzzara Blue Membrane Pump 230v c/w Switch o M BSP & ¾ Hose Tail JI F Suzzara Blue Membrane Pump 230v M BSP & ¾ Hose Tail JI F Suzzara Blue Membrane Pump 110v c/w Switch o / M BSP & ¾ Hose Tail JI AB ABLUE Suzzara Blue C Pump nly Self priming 5 chamber membrane pump with no shaft seal For the mobile transfer of AdBlue where no mains power is available Integrated bypass valve 2m cable & clips for battery connection Protection grade: IP55 Protected on/off switch Uses custom designed o ring sealed plastic fittings Carry handle available as an option uty cycle: 20mins 34lpm MAX FLW RATE Code escription n/ff Switch Max Flow Rate (lpm) V Amps Watts Ports Fluids F Suzzara Blue Membrane Pump 12v o M BSP & ¾ Hose Tail JI F Suzzara Blue Membrane Pump 24v o M BSP & ¾ Hose Tail JI R Carry Handle C PWER 25

25 Pumps / AdBlue Pumps FEATURE Enhanced AdBlue dispensing with the Elite Three 25 IBC pump kit 32lpm MAX FLW RATE AC PWER Piusi Elite Three 25 IBC Pump Kit AB ABLUE The Piusi Elite Three 25 is a deluxe AdBlue pump kit for the transfer of AdBlue from an IBC. It has been introduced into the market as a higher specification alternative to the current IBC pump kits available. Thanks to its array of innovative features, the Elite Three 25 is a sturdier, more durable unit that allows for the simple, accurate and clean transfer of AdBlue into the vehicle. It also benefits from a robust frame that provides the pump with protection when being moved from one IBC to another. What makes the Elite Three 25 high spec AdBlue long life 3 filter for removing any impurities Sturdy stainless steel plate with robust technopolymer roll bars for pump protection against impact SEC connector for attaching the suction hose to the IBC Locking bracket for sturdy connection of the plate to the IBC High capacity hose holder & nozzle holster with removable drip cup for easy cleaning Crimped high quality EPM 6m delivery hose c/w stainless crimps SB325 auto nozzle c/w integrated K24 meter for measuring quantity dispensed & breakaway spout. Also available with magnetic missfilling spout - see table Code escription n/ff Switch Max Flow Rate (lpm) V Filter Nozzle Spout Hose Fluids Auto SB325 F Piusi Elite Three 25 o o Standard 6m del, 1.5m suct J Meter F M What is AdBlue? AdBlue is a synthetic Aqueous Urea Solution (AUS32) required by the majority of heavy duty diesel vehicles purchased after ctober 2006 in order to comply with European Emission Standards. Added to the SCR system of a vehicle s exhaust, the AUS32 vaporises & reacts to reduce the amount of harmful nitrogen oxides released into the air. It is vital that AdBlue is kept pure, as contamination may cause damage to the vehicle & may void the vehicle's warranty. To avoid contamination, only equipment specifically designed for AdBlue should be used from a trusted supplier that understands the industry. Piusi Elite Three 25 c/w Magnetic Spout o o Auto SB325 Meter Standard & Magnetic 6m del, 1.5m suct J 26

26 AdBlue Pumps \ Pumps AB ABLUE Suzzara Blue AC IBC Pump Kit Self priming AC membrane pump on stainless steel plate Ready to use kit for the transfer of AdBlue from an IBC Pro version with auto nozzle & K24 flow meter Basic version with manual nozzle & no meter 6m delivery, 1.5m suction hose & SEC connector Hose & nozzle support with drip catcher Protection grade: IP55 Safety cord for plate attachment to IBC uty cycle: 20mins AB ABLUE Suzzara Blue C IBC Pump Kit Self priming C membrane pump on stainless steel plate Ready to use kit for the transfer of AdBlue from an IBC Pro version with auto nozzle & K24 flow meter Basic version with manual nozzle & no meter 6m delivery, 1.5m suction hose & SEC connector Hose support & nozzle holster with drip catcher Protection grade: IP55 Safety cord for plate attachment to IBC 2m or 4m cable & clips for battery connection uty cycle: 20mins 32lpm MAX FLW RATE Code escription n/ff Switch Max Flow Rate (lpm) V Meter Nozzle Hose Fluids F00201BI0 Suzzara Blue Pro A K24 230v o K24 Auto 6m del, 1.5m suct J F00201BL0 Suzzara Blue Basic M 230v o Manual 6m del, 1.5m suct J F00201BL0.A Suzzara Blue Basic A 230v o Auto 6m del, 1.5m suct J F00201ABA Suzzara Blue Pro A K24 110v o K24 Auto 6m del, 1.5m suct J F00201ABM Suzzara Blue Basic M 110v o Manual 6m del, 1.5m suct J AC PWER 32lpm MAX FLW RATE C PWER Code escription n/ff Switch Max Flow Rate (lpm) V Meter Nozzle Hose F00201A80 Suzzara Blue Pro A K24 12v 2m Cables o K24 Auto 6m del, 1.5m suct 2m J F00201A90 Suzzara Blue Basic M 12v 2m Cables o Manual 6m del, 1.5m suct 2m J F00201A94 Suzzara Blue Basic M 12v 4m Cables o Manual 6m del, 1.5m suct 4m J F00201A824 Suzzara Blue Pro A K24 24v 2m Cables o K24 Auto 6m del, 1.5m suct 2m J F00201A92 Suzzara Blue Basic M 24v 2m Cables o Manual 6m del, 1.5m suct 2m J F00201A924 Suzzara Blue Basic M 24v 4m Cables o Manual 6m del, 1.5m suct 4m J Basic Pro Basic Pro Cable Fluids 27

27 Pumps / AdBlue Pumps 330ml per stroke MAX FLW RATE IBC MUNTING AB ABLUE Manual IBC Pump Kit Self priming piston hand pump on powder coated mild steel plate with locking back bar Cost effective solution for dispensing AdBlue from an IBC Swivelling 90 spout with self closing reed valve 2.2m delivery, 1.8m suction hose & SEC connector Integrated pump locking nut Code escription Max Flow Rate (per stroke) Nozzle Hose Fluids CTS2034 Manual IBC Pump Kit 330ml 19mm Spout 2.2m del, 1.8m suct J 380ml per rev MAX FLW RATE IBC MUNTING AB ABLUE Piusi Stainless Rotary IBC Pump Kit Self priming rotary hand pump with stainless steel outer casing on an IBC bracket Sturdy & durable solution for dispensing AdBlue from an IBC esigned for fitting to the top bar of an IBC only Smooth operation thanks to its rolling handle grip & quality construction 1m suction hose, 2.5m delivery hose & stainless steel spout Spout stopper to prevent the gathering of crystallisation Please note: SEC connector not included Code escription Max Flow Rate (per rev) Nozzle Hose IBC Bracket Fluids F00332B00 Stainless AdBlue Rotary IBC Pump Kit 380ml 19mm Stainless Steel Spout 2.5 m del, 1m suct Stainless Steel J 380ml per rev MAX FLW RATE IBC MUNTING AB ABLUE Stainless Steel Rotary IBC Pump Kit Self priming rotary hand pump with stainless steel outer casing on an IBC bracket Sturdy & durable solution for dispensing AdBlue from an IBC esigned for fitting to lower IBC bars when the IBC is on a bund Fits round & squared bar IBCs Smooth operation thanks to its rolling handle grip & quality construction 3m delivery hose & plastic & stainless steel swivel spout with on/ off valve SEC connector & 2m suction hose Code escription Max Flow Rate (per rev) Nozzle Hose IBC Bracket Fluids CTS1027 Stainless AdBlue Rotary IBC Pump Kit 380ml Spout 3m del, 2m suct Stainless Steel J 28

28 AdBlue Pumps \ Pumps AB ABLUE Suzzara Blue Wall Box Self priming AC membrane pump in a steel locking box A complete AdBlue dispensing kit for wall mounting Automatic nozzle c/w holster secured inside the box 4m delivery hose K24 digital flow meter Protection grade: IP55 Please note: Suction hose not included Suzzara Blue Portable Pump Kit Self priming C membrane pump available as a portable, ready to dispense kit from AdBlue drums and IBCs Manual nozzle & 6m delivery, 1.5m suction hose Plastic foot valve and strainer 2m cables & clips for battery connection Protection grade: IP55 Popular within agricultural & construction environments 32lpm MAX FLW RATE Code escription n/ff Switch Max Flow Rate (lpm) V Meter Nozzle Hose Fluids F A Suzzara Blue Wall Box o K24 Auto 4m delivery J AB ABLUE AC PWER 32lpm MAX FLW RATE C PWER Code escription n/ff Switch Max Flow Rate (lpm) V Nozzle Hose Fluids F00201AA0 Suzzara Blue Portable Kit o Manual 6m del, 1.5m suct J AB ABLUE Piusibox AdBlue Suzzara Blue C pump as a portable pumping solution in a sturdy pull along box c/w wheels Automatic SB325 nozzle c/w breakaway spout mechanism & miss-filling kit 6m delivery hose & 2m suction hose with SEC connector Gloves & AdBlue long life 3 filter for removing any impurities Terminal box with on/off switch & 4m cables & clips Ideal for heavy duty environments thanks to its protective box preventing contamination e.g. construction sites & agriculture 32lpm MAX FLW RATE Code escription Max Flow Rate (lpm) V Amps Nozzle Hose Filter Fluids F Piusibox for AdBlue SB325 Auto 6m del & 2m suct o J C PWER 29

29 Pumps / AdBlue Pumps 32lpm MAX FLW RATE AC PWER 32lpm MAX FLW RATE AC PWER 32lpm MAX FLW RATE C PWER AB ABLUE Suzzara Blue rum Self priming AC membrane pump on a spring loaded stainless steel plate designed to be top mounted onto a drum Ready to dispense kit designed to be easily disconnected and moved between AdBlue drums Manual nozzle c/w anti-drip nozzle holster 6m delivery hose, suction hose & SEC connector Code escription n/ff Switch Max Flow Rate (lpm) V Nozzle Hose Fluids F A Suzzara Blue rum o Manual 6m del J AB ABLUE Suzzara Blue Troll Self priming AC membrane pump on a stainless steel plate designed to be side mounted onto a drum trolley Ready to dispense kit designed to be easily disconnected and moved between AdBlue drums Manual nozzle c/w anti-drip nozzle holster 6m delivery hose, suction hose & SEC connector Heavy duty drum trolley included Code escription n/ff Switch Max Flow Rate (lpm) V Nozzle Hose Fluids F Suzzara Blue Troll 230v o Manual 6m del J F Suzzara Blue Troll 110v o Manual 6m del J AB ABLUE C rum Pump Kit Self priming C membrane pump c/w 2m cable & clips Ready to dispense kit designed to be easily disconnected and moved between AdBlue drums Manual nozzle 4m delivery hose, 905mm suction tube c/w strainer 2 56x4 drum adaptor Code escription n/ff Switch Max Flow Rate (lpm) V Nozzle Hose Fluids CTS2007 AdBlue rum Pump Kit 12v o Manual 4m del, 905mm downtube J CTS2008 AdBlue rum Pump Kit 24v o Manual 4m del, 905mm downtube J 30

30 AdBlue Pumps \ Pumps AB ABLUE Piusi Stainless Steel rum Pump Self priming rotary hand pump with stainless steel outer casing Sturdy & durable solution for dispensing AdBlue from a drum Smooth operation thanks to its rolling handle grip & quality construction 56x4 drum connector & 3 part suction downpipe Version with 2.5m delivery hose & stainless spout available Spout stopper to prevent the gathering of crystallisation (hose version only) AB ABLUE Manual Piston rum Pump Polypropylene piston hand pump c/w viton seals Cost effective solution for dispensing AdBlue from a drum 2 M BSP or 56x4 Tri-sure drum adaptor Telescopic downtube 510mm-920mm ption with delivery hose & spout See page for alternative drum adaptors AB ABLUE Manual Rotary rum Pump Polypropylene rotary hand pump Cost effective solution for dispensing AdBlue from a drum 2 BSP drum adaptor Suction downtube ption with delivery hose & spout See page for mauser & Tri-sure drum adaptors 380ml per rev MAX FLW RATE 56x4 M MUNTING Code escription Max Flow Rate (per rev) Spout elivery Hose owntube Fluids F00332A20 AdBlue Rotary rum Pump c/w Hose 380ml 19mm Stainless Spout 2.5m o J F00332A00 AdBlue Rotary rum Pump 380ml o J 330ml per stroke MAX FLW RATE 2" M BSP / 56x4 MUNTING Code escription Max Flow Rate (per stroke) Spout elivery Hose rum Adaptor owntube Fluids CTS2037 AdBlue Piston rum Pump c/w Hose 330ml 19mm Spout & Hook 2m 56x4 Tri-sure mm J CTS2020 AdBlue Piston rum Pump 330ml 19mm Spout 2" M BSP mm JA 300ml per rev MAX FLW RATE 2" M BSP MUNTING Code escription Max Flow Rate (per rev) Spout elivery Hose owntube Fluids F AdBlue Rotary rum Pump c/w Hose 300ml 19mm Spout & Hook 3m o J F AdBlue Rotary rum Pump 300ml 27mm Spout o J 31

31 Pumps / AdBlue Pumps 220lpm MAX FLW RATE Air TYPE 22lpm MAX FLW RATE Air TYPE 80lpm MAX FLW RATE AC TYPE AB ABLUE A ANTIFREEZE Piusi Air perated iaphragm Pump Self priming double membrane air operated diaphragm pump with polypropylene body Ideal for transferring AdBlue in garage & workshop environments where there is an existing air line Hytrel/PTFE iaphragm & PTFE balls Can run dry without damage ATEX approved to Zone 2 Code escription Max Flow Rate (lpm) Inlet/utlet Air Inlet Self Priming (m) Max Head (m) Max Air Supply (bar) Fluids F00208P00 MP130 A AdBlue Pump 50 ½ F BSP ⅜ F BSP JHI F00208P20 MP140 A AdBlue Pump F BSP ⅜ F BSP JHI F00208P30 MP180 A AdBlue Pump F BSP ⅜ F BSP JHI F00208P40 MP190 A AdBlue Pump ¼ F BSP ½ F BSP JHI IBC Version AB ABLUE W WATER Air perated AdBlue Pump 2:1 ratio air operated AdBlue pump c/w air regulator valve with clock face Ideal for transferring AdBlue in garage, workshops & remote locations using an existing air line IBC Version c/w truck emergency air brake connector to utilise truck air system Available as pump only or part of a drum, wall or IBC mount kit with nozzle & hose Code escription Flow Rate (lpm) Inlet utlet Air Inlet Max Inlet Pressure (bar) Nozzle Hose Fluids CTS9012 Air AdBlue Pump nly 3 bar 1 F BSP 19mm Barb ¼ F BSP 12 J CTS9011 Air AdBlue Pump Wall 3 bar SEC 19mm Barb ¼ F BSP 12 Manual 4m del, 2m suct J CTS9010 Air AdBlue Pump rum 3 bar 2 rum 19mm Barb ¼ F BSP 12 Manual 4m del, downtube J CTS2053 Air AdBlue Pump IBC 3 bar SEC 19mm Barb ¼ F BSP 12 Manual 6m del, 1.5m suct J AB ABLUE Submersible AdBlue Pump Powerful submersible pump with three stage impeller & wearresistant shaft c/w 6m cable esigned for high flow rate applications where increased head pressure is required Anti-debris stainless steel strainer & custom seals to keep the AdBlue pure Thermal overload protection for the motor No start/stop float switch Code escription Max Flow Rate (lpm) Max Pressure (bar/psi) V Hz Amps Watts Ports Fluids AB1000N-A Submersible AdBlue Pump / F BSP J 32

32 AdBlue Pumps \ Pumps AB ABLUE Benefits of the elphin Specifically designed for refilling passenger cars with AdBlue cleanly & safely in a garage/service environment. 2. Allows AdBlue to be bought & dispensed from bulk in 210 litre drums rather than the small, costly throwaway 5 litre containers. 3. Closed, clean filling system that avoids spillage & wastage, and keeps the AdBlue uncontaminated which is imperative. 4. Tried and tested by leading EMs and car dealership networks in the UK and worldwide, as an economical filling solution. 5. Upgrade kit available which weighs the amount of AdBlue allowing customer to chargeback by the kilogram - see table. Please note: AdBlue drum not included How the elphin works Be prepared for Euro VI with the elphin AdBlue Car ispenser SEC connector c/w suction downtube for connecting the system to the drum Self-priming membrane pump to fill the upper holding tank with fluid from the drum 20l upper holding tank with visual indicator to control the amount of AdBlue delivered to the vehicle Sturdy trolley for moving the system from the power point to the vehicle once the upper tank has been filled 2m delivery hose c/w filling valve to gravity fill the vehicle, which you can shut off when the vehicle tank is full System can then be wheeled back to the power point where the electric pump sucks the remaining AdBlue in the hose back into the upper tank 6lpm MAX FLW RATE AC PWER What is Euro VI? FEATURE Euro VI is the latest update to the European emission standards, which require diesel powered vehicles to reduce their emissions down to a certain level. Previous releases saw more heavy duty vehicles including trucks, buses, agricultural & plant machinery being affected, but the Euro VI now covers passenger cars as of September Code escription Max Flow Rate (lpm) V elivery Hose Suction Hose Trolley Upper Tank Fluids F elphin Car ispenser m c/w filling valve owntube c/w SEC o 20l c/w level indicator J F00201K00 Approved Weighing System Kit J 33

33 Pumps / ATEX Pumps FEATURE EX50 C/w connector & nozzle switch What is ATEX approval? 50lpm MAX FLW RATE AC/C PWER The European ATEX/IECEx directives mean that electrical and mechanical equipment used within potentially explosive atmospheres must be designed and built in a way so as not to create sources of ignition, such as sparks, hot surfaces, static electricity and any other sources of combustion able to ignite these potentially explosive mixtures. The Piusi EX50 satisfies this stringent criteria regarding product safety, making it suitable for flammable liquids. Code escription Max Flow Rate (lpm) The safe pumping of flammable liquids with the Piusi EX50 See page 35 for ATEX pump kits RELATE PRUCTS P PETRL K KERSENE Piusi EX50 ATEX Approved Pump The Piusi EX50 fuel transfer pump is ATEX certified to II2G Ex d II A T4 Gb for use in Zone 1, potentially explosive environments and the pumping of flammable liquids. Its careful design and sturdy construction makes it an ideal, long life solution for the dispensing of petrol and kerosene, and the transfer of diesel when undertaken in an environment that contains petrol vapours. Features... Self priming rotary vane pump for flammable liquids & Zone 1 environments Compact & sturdy cast iron pump body Integrated bypass valve c/w check valve & pressure reliefe valve (drum nozzle switch versions only) Incorporated suction unit with filter Fully flanged components for easy maintenance Thermal motor protection ATEX certified: II2G Ex d II A T4 Gb Suitable for diesel, petrol, kerosene, AVGAS, AVJET A1, Aspen 2 & Aspen 4 Version available with drum connector & nozzle switch Low voltage & mains powered versions available Lower flow rate version available for filling small equipment e.g. golf buggies & lawn mowers V Hz Amps uty (mins) Ports Pump n/ff 2 M BSP rum Connector F EX50 ATEX Pump 12v on / 60 off 1 F BSP Flanged Lever AGCS F A EX50 ATEX Pump 12v 25lpm on / 60 off ¾ F BSP Flanged Lever AGCS F EX50 ATEX Pump 12v c/w Connector & Nozzle Switch on / 60 off 1 F BSP Nozzle Switch o Fluids AGCS F EX50 ATEX Pump 230v / on / 30 off 1 F BSP Flanged Lever AGCS F EX50 ATEX Pump 230v c/w Connector & Nozzle Switch / on / 30 off 1 F BSP Nozzle Switch IESEL o AGCS J JET FUEL 34

34 ATEX Pumps \ Pumps IESEL Piusi EX50 ATEX rum Pump EX50 as a drum mounted kit for dispensing flammable liquids in Zone 1 environments directly from a drum Low voltage or mains powered depending upon model ATEX automatic or manual nozzle & 4m delivery hose 30µ water & particle filter ptional mechanical ATEX K33 flow meter Telescopic downtube & 2 drum connector ATEX certified: II2G Ex d II A T4 Gb Suitable for diesel, petrol, kerosene, Aspen 2 & Aspen 4 IESEL P PETRL P PETRL K KERSENE Piusi EX50 ATEX Wall Mounted Kit EX50 as a plated wall mounted kit for dispensing flammable liquids in Zone 1 environments Ideal for wall or tank mounting in static installations ATEX automatic nozzle c/w nozzle holder & switch 4m Parker petrol delivery hose with bend protection Inline mesh suction strainer to remove large impurities and protect the pump from damage Mechanical ATEX K33 flow meter ATEX certified: II2G Ex d II A T4 Gb Suitable for diesel, petrol, kerosene, Aspen 2 & Aspen 4 50lpm MAX FLW RATE AC/C Code escription Max Flow Rate (lpm) V Flow Meter Hose Nozzle Filter Connection Fluids F rum EX50 12V ATEX A m Auto 30µ 2 M BSP rum AGC F rum EX50 12V ATEX M m Manual 30µ 2 M BSP rum AGC F rum EX50 12V ATEX A K K33 4m Auto 30µ 2 M BSP rum AGC F rum EX50 12V ATEX M K K33 4m Manual 30µ 2 M BSP rum AGC F rum EX50 230V ATEX A m Auto 30µ 2 M BSP rum AGC F rum EX50 230V ATEX M m Manual 30µ 2 M BSP rum AGC F rum EX50 230V ATEX A K K33 4m Auto 30µ 2 M BSP rum AGC F rum EX50 230V ATEX M K K33 4m Manual 30µ 2 M BSP rum AGC K KERSENE PWER 50lpm MAX FLW RATE Code escription Max Flow Rate (lpm) V Flow Meter Hose Nozzle Filter Connection Fluids F ST EX50 230v A K K33 4m Auto Mesh Strainer Wall Plate AGC AC PWER See page 60 for ATEX igital Meter INFRMATIN See page 60 for ATEX igital Meter INFRMATIN 35

35 Pumps / Multi-Purpose Pumps 310ml per rev MAX FLW RATE 2" M BSP MUNTING Ultraflo Cast Iron Rotary Hand Pump Ultraflow cast iron constructed rotary vane pump Cost effective solution for dispensing diesel & oil from a drum 2 M BSP drum adaptor & 3 part rigid suction downtube 25mm dispensing spout Max viscosity 410 cst Code escription Max Flow Rate (per rev) utlet owntube Mounting Fluids CTS2001C Cast Iron Rotary Hand Pump 310ml 25mm Bent Spout 1000mm 2 M BSP AF 450ml per rev MAX FLW RATE 2" M BSP MUNTING 1L per rev MAX FLW RATE IESEL IL Aluminium Rotary Hand Pump Lightweight aluminium, corrosion resistant rotary vane pump Cost effective solution for dispensing diesel & oil from a drum 2 M BSP drum adaptor & 3 part rigid suction downtube 25mm dispensing spout & neoprene seal Max viscosity 410 cst Code escription Max Flow Rate (per rev) utlet owntube Mounting Fluids Aluminium Rotary Hand Pump 450ml 25mm Bent Spout 1000mm 2 M BSP AFGC 2" M BSP MUNTING IESEL IESEL IL IL P PETRL P PETRL High Flow Rotary Hand Pump Aluminium alloy constructed rotary gear pump Cost effective solution for dispensing diesel & oil from a drum 2 M BSP drum adaptor & single part rigid suction downtube 25mm dispensing spout & 1.3m convoluted hose Max viscosity 90 cst K KERSENE K KERSENE Code escription Max Flow Rate (per rev) utlet Hose owntube Mounting Fluids CTS2004 High Flow Rotary Hand Pump 1L 32mm Bent Spout 1.3m 1000mm 2 M BSP AFGCH 580ml per stroke MAX FLW RATE 2" M BSP MUNTING High Flow Lever Hand Pump Aluminium alloy constructed lever hand pump Cost effective solution for dispensing diesel & oil from a drum 2 M BSP drum adaptor & 3 part rigid suction downtube 20mm dispensing spout Max viscosity 410 cst Code escription Max Flow Rate (per stroke) utlet owntube Mounting Fluids High Flow Lever Hand Pump 580ml 20mm Spout 850mm 2 M BSP AF IESEL IL A ANTIFREEZE 36

36 Multi-Purpose Pumps \ Pumps IESEL Lever Hand Pump Steel constructed lever hand pump Cost effective solution for dispensing diesel & oil from a drum 2 M BSP drum adaptor & telescopic 2 part rigid suction downtube 20mm dispensing spout Max viscosity 210 cst IESEL IL P PETRL HP100 Lever Hand Pump Aluminium alloy constructed lever hand pump For dispensing diesel, oil & petrol from a drum or tank 2 M BSP drum adaptor K KERSENE 1 F BSP dispensing outlet Plastic adjustable suction pipe 330ml per stroke MAX FLW RATE 2" M BSP MUNTING Code escription Max Flow Rate (per stroke) utlet owntube Mounting Fluids CTS2000C Lever Hand Pump 330ml 20mm Bent Spout mm 2 BSP AF 940ml per stroke MAX FLW RATE 2" BSP MUNTING Code escription Max Flow Rate (per stroke) utlet owntube Mounting Fluids CTS9002 HP100 Lever Hand Pump F BSP mm 2 M BSP AFGC IESEL IL L45 Lever iaphragm Pump Aluminium single lever diaphragm pump esigned for dispensing from 25 or 205ltr oil barrels Can handle solids up to 15mm 2 M BSP drum adaptor & 2 part rigid downtube Rugged construction 2" M BSP MUNTING Code escription Max Flow Rate (per stroke) utlet Suction Inlet owntube Mounting Fluids L45 H Lever Hand Pump 500ml 1 Hose Barb ¾ F BSP 850mm 2 M BSP rum AFI IESEL IL IL W WATER W WATER L120 Lever iaphragm Pump Aluminium self-priming lever diaphragm pump with stainless steel fittings Lightweight, portable floor standing site pump Popular choice for drainage and fuel transfer applications 6m suction hose, hose clips & strainer 500ml per stroke MAX FLW RATE 1400ml per stroke MAX FLW RATE Floor MUNTING Code escription Max Flow Rate (per stroke) utlet Suction Inlet Suction Length Mounting Fluids L120 Floor Standing Lever Hand Pump 1400ml 1 ½ Hose Barb 1 ½ Hose Barb 6m x 1 ½ Hose Floor / Wall AFI 37

37 Pumps / Multi-Purpose Pumps 400ml per rev MAX FLW RATE 2" M BSP MUNTING Stainless Steel Chemical Hand Pump 304 Stainless steel & Teflon rotary hand pump esigned for dispensing a variety of chemicals from a drum 2 M BSP drum adaptor & 3 part rigid suction downtube 25mm bent dispensing spout Max. viscosity 410cSt Code escription Max Flow (per rev) utlet owntube Mounting Fluids CTS2010 Stainless Steel Chemical Hand Pump 400ml 25mm Bent Spout 1060mm 2 M BSP LAFIHJ 400ml per rev MAX FLW RATE 2" M BSP MUNTING 2" M BSP MUNTING Plastic Chemical Hand Pump Plastic/ryton rotary hand pump esigned for dispensing a variety of chemicals from a drum 2 M BSP drum adaptor & suction downtube + filter 27mm bent dispensing spout Max. viscosity 410cSt Code escription Max Flow (per rev) utlet owntube Mounting Fluids CTS2011 Plastic Chemical Hand Pump 400ml 27mm Bent Spout 1060mm 2 M BSP LAFIH 1l per rev MAX FLW RATE High Flow Chemical Hand Pump Plastic/ryton rotary hand pump esigned for high flow dispensing of chemicals from a drum 2 M BSP drum adaptor & suction downtube 25mm dispensing spout c/w 1.3m convoluted hose Max. viscosity 90cSt Code escription Max Flow (per rev) utlet owntube Mounting Fluids CTS2012 Plastic High Flow Chemical Hand Pump 1l 25mm Bent Spout c/w Hose 1000mm 2 M BSP LAFIH 400ml per stroke MAX FLW RATE 2" M BSP MUNTING C CHEMICAL C CHEMICAL C CHEMICAL C CHEMICAL IESEL IESEL IESEL IL IL IL W WATER W WATER W WATER A ANTIFREEZE A ANTIFREEZE A ANTIFREEZE AB ABLUE Plastic Chemical Lever Hand Pump Plastic/ryton lever hand pump esigned for dispensing a variety of chemicals from a drum 2 M BSP drum adaptor & telescopic suction downtube 1.4m PE hose, nozzle & lockable handle Max viscosity 410 cst Code escription Max Flow (per stroke) utlet owntube Mounting Fluids CTS2013 Plastic Chemical Lever Hand Pump 400ml PE hose c/w Nozzle 950mm 2 M BSP LAFIH IESEL IL W WATER A ANTIFREEZE 38

38 Multi-Purpose Pumps \ Pumps IESEL IL ouble iaphragm Hand Pump ouble diaphragm lever hand pump Alloy body & resistant nitrile rubber diaphragm For dispensing diesel, oil & petrol from a drum only 2 M BSP bung adaptor for drum mounting 2.5m x ¾ anti-static neoprene rubber delivery hose Nozzle with built in nozzle holster support Telescopic suction downtube & NRV Incorporated wire mesh screen to filter large debris Fluid Buddy Submersible Pump Compact & portable submersible pump for the transfer of diesel, & water CE marked, UKAS quality assured manufacturer Removable suction filter for easy cleaning 3m cable & clips for battery connection Should not be run dry Max. fluid temperature 30 C Two different flow rate versions PT Air Compressor PT driven air compressor for pumping a tractor and plant tyres Purposely designed for toolbox storage 4.5m rubber air hose c/w tyre valve connector Quick release pin for holding the PT compressor to the PT shaft CE marked P PETRL 400ml per stroke MAX FLW RATE 2" M BSP MUNTING 30lpm MAX FLW RATE C PWER 90lpm AIR VLUME PT Shaft PWER Code escription Max Flow Rate (per stroke) utlet owntube Mounting Fluids CTS2003 ouble iaphragm Hand Pump 400ml 2.5m x ¾ Hose Telescopic 2 M BSP Bung Adaptor AFG IESEL Code escription Max Flow Rate (lpm) V utlet uty (mins) Cable & Clips Suction Filter Fluids CTS2044 Fluid Buddy 20lpm mm Hose Tail 30 on / 20 off 3m o AI CTS2045 Fluid Buddy 30lpm mm Hose Tail 30 on / 20 off 3m o AI AIR AIR W WATER Code escription Cylinder Bore iameter (mm) Stroke (mm) Air Volume (lpm) CTS2042 PT Air Compressor Working Pressure (bar) Max PT Speed (rpm)

39 Pumps / Multi-Purpose Pumps C/w Hose Pump nly 380ml per rev MAX FLW RATE 2" BSP MUNTING 1630ml per rev MAX FLW RATE Piusi Stainless Steel Hand Pump Self priming rotary hand pump with stainless steel outer casing designed as a more reliable & quality manual option Sturdy & durable solution for dispensing diesel & oil from a drum Smooth operation thanks to its rolling handle grip & quality construction 2 M BSP drum connector & suction downtube Version with 3m delivery hose & swivel spout c/w on/off valve available Version without hose has an "S" type spout ideal for dispensing straight into an oil jug Code escription Max Flow Rate (per rev) Spout elivery Hose owntube Fluids CTS2074 Stainless Rotary rum Pump c/w Hose 380ml 19mm Swivel n/ff Spout 3m o AF F Stainless Rotary rum Pump 380ml S Spout o AF Cast Iron Bronze Lugs MUNTING IESEL IESEL IL W WATER Semi-Rotary Hand Pump Cast iron constructed semi-rotary vane pump (bronze version available for water) Cost effective solution for dispensing or transferring of diesel fuel Wooden/cast spindle handle Backplate lugs for mounting Range of size and flow rate versions available depending upon individual requirements Removable inlet/outlet flanges Replaceable gland packing Code escription Max Flow Rate (per rev) Material Suction Inlet utlet Mounting Fluids CTS5010 K0 Semi Rotary Pump 200ml Cast Iron ½ F BSP Flanged ½ F BSP Flanged Backplate lugs A CTS5011 K1 Semi Rotary Pump 300ml Cast Iron ¾ F BSP Flanged ¾ F BSP Flanged Backplate lugs A CTS5000C K2 Semi Rotary Pump 400ml Cast Iron 1 F BSP Flanged 1 F BSP Flanged Backplate lugs A CTS5012 K3 Semi Rotary Pump 520ml Cast Iron 1 ¼ F BSP Flanged 1 ¼ F BSP Flanged Backplate lugs A CTS5013 K4 Semi Rotary Pump 780ml Cast Iron 1 ¼ F BSP Flanged 1 ¼ F BSP Flanged Backplate lugs A CTS5014 K5 Semi Rotary Pump 960ml Cast Iron 1 ½ F BSP Flanged 1 ½ F BSP Flanged Backplate lugs A CTS5015 K7 Semi Rotary Pump 1630ml Cast Iron 2 F BSP Flanged 2 F BSP Flanged Backplate lugs A CTS5020 Excelsior Semi-Rotary Pump 480ml Bronze 1 F BSP Flanged 1 F BSP Flanged Backplate lugs I 40

40 Multi-Purpose Pumps \ Pumps IESEL Liquid Extraction & ischarge Pump Lightweight & portable multi-purpose liquid extraction pump in two versions; extraction only & extraction & discharge Extracts the fluid via the supplied suction probes & stores up to 6litres in its integral container, which takes 2.5mins to fill When full, remove the top plug & pour out the contents, or discharge version can also pump the contents back out Both versions operate manually, or extraction only version can also be connected to a compressed air supply Removes water & fuel from tank bunds, bilge water, oil from vehicles, lawn mowers & hydraulic reservoirs Each pump has 10mm, 7mm, 6mm x 900mm probes ischarge version c/w 10mm push fit connector & lever ball valve ptional kit c/w 6m suction tube & brass weight for removing fluid from the bottom of a storage tank or deep bund area ischarge model can be used with optional oil line priming kit 2.4lpm MAX FLW RATE Floor MUNTING Code escription Max Flow Rate (lpm) Capacity (l) Probes peration Vacuum Gauge Max Bar Air Inlet Fluids CTS2075 Liquid Extraction Pump o Manual/Air 6 ¼ F BSP AFIC CTS2076 Liquid Extraction & ischarge Pump o Manual o AFIC CTS2079 Storage Tank Extraction Kit o AFIC CTS2077 il Line Priming Kit for CTS2076 o AFC CTS2086 Replacement Probes for CTS2075 o AFIC CTS2089 Replacement Probes for CTS2076 o AFIC IESEL IL W WATER K KERSENE BP3000 rum Kit Complete kit for installing a BP3000 battery kit onto a fuel drum Two versions available; standard for mounting BP3000 battery kit & a version for also fitting a meter or filter Telescopic 1 BSP suction downtube mm 2 M BSP drum connector c/w 1 F BSP inner thread for connection to the suction pipe 90 flanged connector Metal adjustable nozzle holster 90 elbow & hose tail (meter/filter version only) Please note: Pump is not included BP3000 PUMP TYPES See page 7 for BP3000 Battery Kit RELATE PRUCTS Extraction nly Extraction & ischarge rum Kit Kit in use Code escription owntube (mm) rum Connector Nozzle Holster 90 Flange 90 Elbow Hose Tail Fluids F BP3000 rum Kit M BSP o 1 A F BP3000 rum Kit Meter/Filter M BSP o 2 o o A 41

41 Pumps / Multi-Purpose Pumps Carry Plate Kit Kit in use Plate TYPE Small PUMP TYPES Frame TYPE Small/Large PUMP TYPES ANY FLUI Piusi Pump Carry Plate Pump bed plate with carry handle for the easy moving of a pump if the refuelling point may change esigned for use with the Piusi Panther & Bi-Pump range but can be used with similar sized models Reusable heavy duty cable tie for neatly & firmly connecting the pump s hoses to the handle 4 x rubber feet for sturdily mounting the plate when the pump is in operation c/w the required nuts and bolts for fitting Carry plate only is also available without the added accessories Please note: Pump is not included Code escription Width (mm) Length (mm) Height (mm) Nuts & Bolts Rubber Mounts Cable Tie FRM005 Piusi Pump Carry Plate Kit o o o R Piusi Pump Carry Plate nly Carry Frame Kit Kit in use See pages 6 & 17 for related pumps RELATE PRUCTS See pages 6 & 17 for related pumps RELATE PRUCTS ANY FLUI Pump Carry Frames Tubular steel crash frame with steel bed plate to provide all-round pump protection & carry facility Small version is recommended for the Piusi Panther & Bi-Pump ranges Large version is recommended for the Piusi E80/120 & Viscomat ranges Reusable heavy duty cable tie for neatly & firmly connecting the pump s hoses to the frame c/w the required nuts and bolts for fitting Carry plate only is also available without the added accessories Please note: Pump is not included Code escription Width (mm) Length (mm) Height (mm) Nuts & Bolts Rubber Mounts Cable Tie FRM003 Small Pump Carry Frame Kit o o o FRM004 Large Pump Carry Frame Kit o o o FRM001 Small Pump Carry Frame nly FRM002 Large Pump Carry Frame nly

42 Multi-Purpose Pumps \ Pumps IESEL Piusi Garda Self priming gear pump for the transfer of lubricants & viscous fluids Traditionally designed for marine applications, but also for industrial use Bronze body, stainless steel shaft & bronze or teflon gears Suitable for mounting in any position Available in a range of voltages & flow rates Low voltage versions available for intermittent use Mains version available for continuous running, equipped with thermal protection Piusi Amalfi Self priming flexible impeller pump for the transfer clean, dirty & salt water Capable of handling solid particles & debris without damage to the pump Plastic body, stainless steel inside chamber & shaft Must not be run dry Available in a range of voltages & flow rates Low voltage version traditionally designed for pumping bilge water in marine applications Mains version available for continuous running, equipped with thermal protection Garda C Garda AC Code escription n/ff Switch Max Flow Rate (lpm) V Hz Amps Max Pressure (bar) Ports Fluids NMT450000A Garda 1 12v ⅜ F BSP AFI NMT450001A Garda 1 24v ⅜ F BSP AFI NMT450002A Garda 2 12v ⅜ F BSP AFI NMT450003A Garda 2 24v ⅜ F BSP AFI NMT460000A Garda 2 12v c/w 2m Clips o ⅜ F BSP AFI NMT460001A Garda 2 24v c/w 2m Clips o ⅜ F BSP AFI NMT Garda 5 230v ⅜ F BSP AFI W WATER IL W WATER 10lpm MAX FLW RATE AC/C 34lpm MAX FLW RATE Amalfi C Amalfi AC Code escription n/ff Switch Max Flow Rate (lpm) V Hz Amps Max Pressure (bar) Ports Fluids NMT Amalfi 1 12v ½ F BSP I NMT Amalfi 1 24v ½ F BSP I NMT Amalfi 5 230v ½ F BSP I PWER AC/C PWER 43

43 Pumps / Water Pumps 2" Model 500lpm MAX FLW RATE Engine TYPE Engine riven Water Pumps 4 stroke petrol engine driven pump with recoil start For mobile, high flow water transfer where mains power is unavailable 1 models plate mounted, 2 models in steel frame Carry facility for portable use Must not be run dry If used with a nozzle, a pressure relief valve or damper valve must be used Code escription Running Fuel Tank Size (l) Max Flow Rate (lpm) Max Lift (m) Max Head (m) Ports Fluids CTS125EW 1 Engine riven Pump UL Petrol Hose Tail I CTS2500EW 2 Engine riven Pump UL Petrol Hose Tail I CTS125E 1 amper Valve for Portable Use IAM CTS125EP 1" Pressure Relief Valve IAM CTS2500EP 2 Pressure Relief Valve IAM 125lpm MAX FLW RATE Engine TYPE Flood Water Pump Kit Ready to use kit for pumping away flood water in outdoor environments 1 4 stroke petrol engine driven pump with recoil start 1 x 9m wire braided suction & 10m lay flat delivery hose 4 x sand bags for absorbing flood water Plastic carry box for keeping kit items together 1 hose tails & suction strainer Code escription Running Fuel Tank Size (l) Max Flow Rate (lpm) Max Lift (m) Max Head (m) Ports Fluids CTS Flood Water Pump Kit UL Petrol Hose Tail I See page 16 for Honda engine model RELATE PRUCTS 780lpm MAX FLW RATE Engine TYPE W WATER W WATER W WATER Site Buddy Trash Pump Electric start diesel engine driven pump c/w starter battery For mobile, high flow dirty water transfer where mains power is unavailable e.g. on construction sites & farms Hardened cast iron impeller able to handle solids up to 25mm Silicon carbide mechanical shaft seal Frame with off-road wheels & carry handles for uneven ground 13.5litre fuel tank for long running time between fill-ups European electronics in the engine c/w hose tails, strainer, clips & rubber NRV to aid priming Code escription Running Fuel Tank Size (l) Max Flow Rate (lpm) Max Lift (m) Max Head (m) Ports Fluids TPP102 Site Buddy Trash Pump iesel Hose Tail I 44

44 Contents \ Fuel Management Systems FUEL MANAGEMENT SYSTEMS FUEL MANAGEMENT IL MANAGEMENT 54 FUEL IL 54 45

45 Fuel Management Systems / Fuel Management See page 48 for PC software RELATE PRUCTS Retrofit TYPE AC/C PWER ANY FLUI Piusi MC Box Cost effective fuel management panel for retrofitting to existing dispensing systems Limits pump access to authorised users via pin code or electronic key (if purchased) Records transaction data such as user, date, time & QTY Locally holds 255 dispenser transactions to view at the unit Facility to record vehicle registration number & odometer readings Pump start/stop & pre-set dispense features Can be connected to the cio digital level gauge for pump cut off & nozzle switch for pump start/stop Can download data to a PC if purchasing the software pack Code escription V Pulse Meter PC Software Manager Key User Keys Max Users Pulse Input (pp/l) Fluids A MC Box Complete 230v 80 User 230 K600 o o N F B MC Box nly 230v 80 User N F A MC Box nly 110v 80 User N F MC Box nly 230v 120 User N F A MC Box nly 230v 120 User AdBlue J F MC Box nly 12v 120 User N F MC Box nly 24v 120 User N See page 48 for PC software RELATE PRUCTS ispenser TYPE AC/C PWER IESEL Piusi Cube 70MC Compact fuel management unit complete with dispensing system Limits pump access to authorised users via pin code or electronic key (if purchased) Records transaction data such as user, date, time & QTY Locally holds 255 dispenser transactions to view at the unit Facility to record vehicle registration number & odometer readings Integrated pump, nozzle, delivery hose & meter Nozzle holster with pump start/stop & pre-set dispense feature Can be connected to an cio digital level gauge for pump cut off Can download data to a PC if purchasing the software pack Code escription Max Flow Rate (lpm) V Pulse Meter Nozzle Hose Max Users Fluids 59400B Cube 70MC 230v 50 User K600 Auto 4m 50 A 59415A Cube 70MC 230v 120 User K600 Auto 4m 120 A 59413A Cube 70MC 12v 50 User K600 Auto 4m 50 A 59414A Cube 70MC 24v 50 User K600 Auto 4m 50 A F12708 Cube 70MC Pedestal 46

46 Fuel Management \ Fuel Management Systems IESEL Piusi Self Service MC Enclosed fuel management unit complete with dispensing system Limits pump access to authorised users via pin code or electronic key (if purchased) Records transaction data such as user, date, time & QTY Locally holds 255 dispenser transactions to view at the unit Facility to record vehicle registration number & odometer readings Integrated pump, nozzle, delivery hose & meter Nozzle holster with pump start/stop & pre-set dispense feature Can be connected to an cio digital level gauge for pump cut off Sturdy structure with front door for easy maintenance Can download data to a PC if purchasing the software pack Large freestanding unit or mini version for tank mounting available IESEL Piusi Self Service FM Enclosed fuel management unit complete with dispensing system Limits pump access to authorised users via pin code or electronic key (if purchased) Records transaction data such as user, date, time & QTY Locally holds 255 dispenser transactions to view at the unit Facility to record vehicle registration number & odometer readings Integrated pump, nozzle, delivery hose & meter Nozzle holster with pump start/stop & pre-set dispense feature Integrated ccio level gauge & ticket printer supplied as standard Sturdy structure with front door for easy maintenance Can download data to a PC if purchasing the software pack Large freestanding unit or mini version for tank mounting available ispenser TYPE AC PWER ispenser TYPE AC PWER See page 48 for PC software RELATE PRUCTS Code escription Max Flow Rate (lpm) V Pulse Meter Nozzle Hose Water Filter Max Users Fluids 738B0A Self Service 70MC Mini 80 User K600 Auto 4m 80 A 73801B Self Service 70MC 80 User K600 Auto 4m 30µ 80 A 741B0B Self Service 100MC Mini 80 User K600 Auto 4m 80 A 74101B Self Service 100MC 80 User K600 Auto 4m 30µ 80 A Self Service 100MC 80 User + Printer K600 Auto 4m 30µ 80 A See page 48 for PC software RELATE PRUCTS Code escription Max Flow Rate (lpm) V Pulse Meter Nozzle Hose Water Filter cio Ticket Printer Max Users Fluids 739B00 Self Service 70FM Mini 120 User K600 Auto 4m o o 120 A 73900B Self Service 70FM 120 User K600 Auto 4m 30µ o o 120 A 742B00 Self Service 100FM Mini 120 User K600 Auto 4m o o 120 A 74200B Self Service 100FM 120 User K600 Auto 4m 30µ o o 120 A 47

47 Fuel Management Systems / Fuel Management Self Service MC Breakaway Spout ispenser TYPE AC PWER See page 48 for PC software RELATE PRUCTS AB ABLUE Piusi Self Service MC AdBlue Freestanding management unit complete with dispensing system specially designed for AdBlue applications Limits pump access to authorised users via pin code or electronic key (if purchased) Records transaction data such as user, date, time & QTY dispensed Locally holds 255 dispenser transactions to view at the unit Facility to record vehicle registration number & odometer readings Integrated pump, delivery hose & meter SB325 automatic nozzle c/w breakaway spout mechanism for cheap & easy repair if vehicle drives off with nozzle in fill point Nozzle holster with pump start/stop & pre-set dispense feature Can be connected to the AdBlue cio digital level gauge for pump cut off Sturdy structure with front door for easy maintenance Code escription Max Flow Rate (lpm) V uty Cycle Pulse Meter Nozzle Hose Filter Max Users Fluids Self Service MC AdBlue mins K24 SB325 Auto 6m 70µ 80 J Key Reader Hardwire ST Piusi SYSTEM TYPE See page 49 for advanced software RELATE PRUCTS ANY FLUI Piusi Self Service esk PC Software For use with the Piusi MC Box, Cube & Self Service FMS units Allows transaction data to be viewed on a PC rather than just at the management unit Simple & easy to comprehend spreadsheet reports isplays transactions by user, date, vehicle or dispenser ata can be transferred through hardwiring or a key reader connected to the PC via USB Additional keys & replacement software Cs available if required Wi-Fi connector pack available when hardwiring is not possible Please note: If you are buying replacement keys for an old system, check that you are buying the correct colour keys Code escription Connection Software C Hardwire Interface Key Reader Manager Key User Keys Fluids F MC/FM Software - Yellow Key USB o o o 10 N F12710 MC/FM Software - Hardwire USB o o N R Additional User Keys - Yellow 10 N R Additional User Keys - Green 10 N R12496 Manager Key o N R Replacement Software isk o N Key Reader o N R USB Adaptor for Key Reader USB N F PW-Wifi RS485 N 48

48 Fuel Management \ Fuel Management Systems ANY FLUI MC Pro Software Easy to use Windows-based software add-on to enhance standard FMS reporting For use with any standard Piusi FMS in conjunction with the Self Service esk software isplays calculated tank levels visually, in litres & the percentage remaining Records fuel stock delivery history Calculates vehicles MPG & fuel consumption cost isplays the data by user, date, vehicle or dispenser Allows the addition of external refuelling transactions to show true fuel usage data Correction of existing refuelling transactions Custom Pan-European language translation files can be added ST Piusi SYSTEM TYPE S/S esk FR USE WITH Code escription Software C For use with Fluids MCPR MC Pro Software o Standard Piusi FMS N ANY FLUI Piusi Access 85 Electronic pump control that limits pump access to authorised users via electronic key A cheaper security alternative to more complex fuel management systems if reporting is not required Variable timed delivery & emergency pump start/stop button Easy to retrofit to existing tank installations via integrated mounting tabs LE status information for operation & alerts Can be connected to a nozzle switch for start/stop operation Can be connected to an cio or low level probe to protect the pump from dry running Available as part of a ready to use retail pack c/w 1 manager key & 1 user key to get the system set up Retrofit TYPE AC PWER See page 48 for electronic keys RELATE PRUCTS Code escription V Hz Max Users Manager Key User Key Fluids F Access N ACC85000 Access 86 Retail Pack N isk Screenshot Access 85 In use 49

49 Fuel Management Systems / Fuel Management Give the manager full control over their fuel, drivers and vehicles with FEATURE 1. Site Simply set up & view the systems you have on site View all of the Self Service 2.0 systems you have connected to the Wi-Fi/LAN on the site Name the system location for easy identification e.g. Main Tank, Back Yard Tank Select the tank fluid to differentiate between diesel & AdBlue tanks Set a low level tank alarm to warn the software user, or set the pump to stop dispensing when the level is hit Set tank capacity & dimensions from the PC See pages for Self Service 2.0 units RELATE PRUCTS See page 53 for user & driver keys RELATE PRUCTS Add storage tank fills (with an cio 2.0 connected the increase in level will automatically be detected) Piusi Self Service 2.0 Range Self Service 2.0 is the brand new, innovative fuel management series from Piusi for managing and monitoring any 2.0 unit on a site. It benefits from a plug and play real time, interactive PC based software interface with enhanced user functionality for the manager, whilst still providing those dispensing the fuel with the familiarity of the industry known Piusi units. System requirements Requires onsite internet connection via LAN or Wi-Fi (extra Wi-Fi module sold separately) Minimum system requirements - Pentium 4/AM Athlon x64, 2Ghz, 2GB RAM, 20GB hard disk space, Windows XP, Vista, 7, 8, 8.1 The software will manage up to 4 systems should you have more than one tank on site that you require a 2.0 unit for 2. Tank Watchdog Easily monitor the real time fuel levels of all tanks on site View all tanks, set location name & which systems are installed on the tank for easy identification Visual indication of fluid type & tank level, tank capacity & the percentage of contents remaining Identify tanks that have hit their set low level alarm, alerting the user that a fuel delivery is required View a graph of the fuel level or the level change over a set time period, which helps identify unusual activity 50

50 Fuel Management \ Fuel Management Systems 3. rivers Supervise your drivers & monitor their activity See who has taken what QTY of fuel, on what dates, & what vehicles they have refilled to help identify any unusual activity Add drivers, amend their details & assign vehicles they are allowed to drive isable a driver if they leave the company to prevent them from being able to dispense fuel Set a driver maximum fuel consumption alarm to warn the software user, or set the pump to stop dispensing then the limit is hit Add any external refuelling transactions to give a true view of drivers total fuel use 5. Report Clearly view & export your customised data Filter the data you wish to review by time period, vehicle, driver, fluid and device/tank Grouped returned data by date, vehicle, driver or device/tank, allowing you to analyse the data as simply as possible Viewed the data on screen graphically or export it into a nicely presented PF file or a functional Excel spreadsheet depending upon user preference 4. Vehicles Manage your vehicles & their fuel consumption See vehicle fuel consumption, the miles it has travelled & how often it is refuelled to help you identify any unusual activity View/change the vehicle details e.g. vehicle icon, registration plate & model Add a maximum tank size to ensure that no more fuel can be dispensed than what is required for that vehicle Set an abnormal fuel consumption alarm to the software user set the pump to stop dispensing when the limit is hit 6. ashboard View the information you need most at a glance A widget based, colourful & clear overview of the information recorded by the Self Service 2.0 software Two screens are available for viewing; a dashboard on the Site information and a dashboard on the rivers & Vehicles data. 51

51 Fuel Management Systems / Fuel Management See pages for 2.0 software features RELATE PRUCTS Retrofit TYPE AC PWER ispenser TYPE AC PWER ANY FLUI Piusi MC Box 2.0 Kit Cost effective management panel for fitting to existing dispensers c/w 2.0 software for enhanced monitoring of fuel, drivers & vehicles Limits access to authorised drivers & vehicles via electronic keys Records transaction data such as driver, vehicle, date, time & QTY Facility to record vehicle odometer readings Pump start/stop & pre-set dispense features Equipped with a LAN connection box for linking to a PC network Locally holds 500 transactions if network connection is temporarily lost Can be connected to an cio 2.0 & nozzle switch Code escription V Pulse Meter river Keys Vehicle Keys Max Users Fluids CTS3100 MC Box 2.0 Kit 230 K600/ N See pages for 2.0 software features RELATE PRUCTS ispenser TYPE AC PWER IESEL Piusi Cube MC 2.0 Kit Compact fuel management unit complete with dispensing system c/w 2.0 software for enhanced monitoring of fuel, drivers & vehicles Limits access to authorised drivers & vehicles via electronic keys Records transaction data such as driver, vehicle, date, time & QTY Facility to record vehicle odometer readings Nozzle holster with pump start/stop & pre-set dispense feature Equipped with a LAN connection box for linking to a PC network Locally holds 500 transactions if network connection is temporarily lost Can be connected to an cio 2.0 Code escription Max Flow Rate (lpm) V Pulse Meter Nozzle Hose river Keys Vehicle Keys Max Users Fluids CTS3101 Cube 70MC 2.0 Kit K600/3 Auto 4m A CTS3102 Cube 90MC 2.0 Kit K600/3 Auto 4m A See pages for 2.0 software features RELATE PRUCTS IESEL Piusi Self Service MC 2.0 Kit Freestanding management unit complete with dispensing system c/w 2.0 software for enhanced monitoring of fuel, drivers & vehicles Limits access to authorised drivers & vehicles via electronic keys Records transaction data such as driver, vehicle, date, time & QTY Facility to record vehicle odometer readings Nozzle holster with pump start/stop & pre-set dispense feature Equipped with a LAN connection box for linking to a PC network Locally holds 500 transactions if network connection is temporarily lost Can be connected to an cio 2.0 Code escription Max Flow Rate (lpm) V Pulse Meter Nozzle Hose Water Filter river Keys Vehicle Keys Max Users Fluids CTS3103 Self Service MC 2.0 Kit K600/3 Auto 4m 30µ A 52

52 Fuel Management \ Fuel Management Systems IESEL Piusi Self Service FM 2.0 Kit Freestanding management unit complete with dispensing system c/w 2.0 software for enhanced monitoring of fuel, drivers & vehicles Limits access to authorised drivers & vehicles via electronic keys Records transaction data such as driver, vehicle, date, time & QTY Facility to record vehicle odometer readings Nozzle holster with pump start/stop & pre-set dispense feature Equipped with a LAN connection box for linking to a PC network Locally holds 500 transactions if network connection is temporarily lost cio 2.0 level gauge & ticket printer supplied as standard ANY FLUI Self Service 2.0 Extras Extra packs of 10 driver (yellow) and 10 user (blue) touch keys available as extras to the standard kits that have 10 keys packaged with them Wi-Fi connector pack available when running a LAN cable is not possible Please note: ther software versions available to handle up to 1000 drivers and 1000 vehicles ispenser TYPE AC PWER Yellow RIVER KEYS Blue VEHICLE KEYS See pages for 2.0 software features RELATE PRUCTS Code escription Max Flow Rate (lpm) V Pulse Meter Nozzle Hose Water cio river Keys Vehicle Keys Max Users Fluids CTS3104 Self Service FM 2.0 Kit K600/3 Auto 4m 30µ o A IESEL AB ABLUE Piusi cio 2.0 Continuous reading, hydrostatic tank contents gauge igital display reading in percentage, level or volume When level alert is activated the display flashes 2 relays for connecting to other equipment e.g. level alarm or BMS Version (LAN) for connecting to existing 2.0 software for montioring a tank with no pump Version (RS485) for connecting to existing 2.0 hardware e.g. Cube MC Stainless steel weight available for use with AdBlue %/Litres/mm REAING Code escription Keys Colour Use With Fluids R river Key Pack 10 Yellow Self Service 2.0 N R Vehicle Key Pack 10 Blue Self Service 2.0 N F PW Wi-Fi 2.0 N AC PWER See pages for 2.0 software features RELATE PRUCTS Code escription V Tank Height (mm) Accuracy Capillary (m) Chamber Tank Fitting Chamber Weight Working Temp Fluids F cio 2.0 LAN /-1% 10 ½ M BSP Brass -20 C/+50 C A F cio 2.0 RS /-1% 10 ½ M BSP Brass -20 C/+50 C A F AdBlue Weight Stainless Steel J Blue Vehicle Key Yellow river Key 53

53 Fuel Management Systems / il Management Enhance the way you manage your garage, work FEATURE GPV Bi-Valve Easyview Nozzle Complete garage management functionality... Monitor & control your jobs orders & fluids with the See page 22 for air operated oil pumps RELATE PRUCTS See page 77 for oil hose reels RELATE PRUCTS Add and monitor outstanding, in process & completed jobs Add fluid dispensing transactions to a job including how much to be dispensed, in what bay and using which reel Add any other jobs e.g. brakes, tyres, bodywork, who is going to do it, in what bay/area & how long it should take View how much of a job is complete & the tasks outstanding Manage your workers' time & tasks Add and view users authorised to perform certain tasks View workers currently busy, what bay they are working in & who is free to perform a task Add worker shifts to see who is available to allocate jobs to Monitor & display tanks on site Set up & view the tank/drum/storage containers on site, their location and which reels they are connected to View quantity of fluid left in a container for stock monitoring Piusi MC 2.0 Range MC 2.0 is much more than just an oil management system; it is designed to give the manager complete control over their garage. it helps to plan and monitor all jobs, including mechanic task scheduling for each bay, as well managing the accurate dispensing of fluids. Basic installation GPV Bi-valve - made up of two solenoids; a larger one dispenses at full flow & shuts off when the transaction is almost complete. A smaller one then allows the remainder to trickle through for accuracy. ne GPV is needed per dispensing reel. Easyview nozzle - manual nozzle with LC display, which shows the user what the GPV has dispensed USB Software - controls up to 30 GPVs, as well as many more garage acitivities. MC 2.0 wall mounted & touchscreen tablet control units available, as well as bay information screens & customer progress TV modules. Please ask for more information. Manage workshop areas Set up garage areas to easily identify the bays free/in use within them e.g. corner workshop, main garage area Allocate the reels that operate within the area so that jobs can easily be allocated to a particular bay Colour code reels for easy reference i.e. all oil reels one colour & all antifreeze another Code escription V Max Flow Rate (lpm) Connection Fluids F MC 2.0 USB Software USB (to computer) N F GPV 2.0 Bi-Valve ½ F BSP v 50/60Hz 30 Wi-FI (to software) F F Easyview Rigid Spout Nozzle 30 Zigbee (to GPV) F 54

54 Contents \ Flow Meters FLW METERS MECHANICAL IGITAL PULSE MECHANICAL IGITAL PULSE

55 Flow Meters / Mechanical Flow Meters lpm FLW RATE RANGE +/-1% ACCURACY lpm FLW RATE RANGE IESEL Piusi K33 Flow Meter Polybutylene nutating disk meter with mechanical display to measure the quantity of fuel that has been dispensed Can work in gravity conditions thanks to low minimum flow rate Meter body can be rotated to allow flow from 4 directions Easy to install and calibrate if required +/-1% accuracy after calibration 3 digit resettable & 6 digit non-resettable totaliser Working temperature -20 c/+60 c ATEX version available for use in flammable environments IESEL IL IL P PETRL K KERSENE Code escription Flow Rate (lpm) Pressure (bar/psi) Inlet utlet Totaliser Fluids K33 iesel /145 1 F BSP 1 F BSP 0.1 to Resettable A K33 il /145 1 F BSP 1 F BSP 0.1 to Resettable F F K33 ATEX /50 1 F BSP 1 F BSP 0.1 to Resettable AGC +/-1% ACCURACY Piusi K44 Flow Meter Polybutylene nutating disk meter with mechanical display to measure the quantity of fuel that has been dispensed Can work in gravity conditions thanks to low minimum flow rate Meter body can be rotated to allow flow from 4 directions Easy to install and calibrate if required +/-1% accuracy after calibration 4 digit resettable & 8 digit non-resettable totaliser Working temperature -20 c/+60 c Pulsar version available: 10 pulses per litre, 6-24v C 3 wire Code escription Flow Rate (lpm) Pressure (bar/psi) Inlet utlet Totaliser Fluids K44 iesel /145 1 F BSP 1 F BSP 0.1 to Resettable A K44 il /145 1 F BSP 1 F BSP 0.1 to Resettable F 56500A K44 Pulsar /145 1 F BSP 1 F BSP 0.1 to Resettable A 56

56 Mechanical Flow Meters \ Flow Meters IESEL Piusi K700 Flow Meter val gear meter with mechanical display to measure the quantity of fuel that has been dispensed Meter body can be rotated to allow flow from 4 directions Easy to install and calibrate if required +/-1% accuracy after calibration 4 digit resettable & 8 digit non-resettable totaliser Working temperature -20 c/+60 c 400µ inlet filter IESEL K KERSENE B3 B30 Fill-Rite Series 900 Meter Nutating disk meter with mechanical display to measure the quantity of fuel that has been dispensed Can work in gravity conditions thanks to low minimum flow rate Meter body can be rotated to allow flow from 4 directions Easy to install and calibrate if required +/-2% accuracy after calibration 4 digit resettable & 8 digit non-resettable totaliser Working temperature -26 c/+66 c Ex II 2G c T6 approved lpm FLW RATE RANGE +/-1% ACCURACY Code escription Flow Rate (lpm) Pressure (bar/psi) Inlet utlet Totaliser Fluids F K700M /145 1 ½ F BSP Flanged 1 ½ F BSP Flanged 0.1 to Resettable A P PETRL lpm FLW RATE RANGE +/-2% ACCURACY Code escription Flow Rate (lpm) Pressure (bar/psi) Inlet utlet Totaliser Fluids E Series 1 ½ /50 1 ½ F BSP Flanged 1 ½ F BSP Flanged 0.1 to Resettable ACMG 57

57 Flow Meters / Mechanical Flow Meters lph* FLW RATE RANGE +/-1% ACCURACY lph FLW RATE RANGE IESEL HZ3 il Meter Mechanical display meter to measure even small quantities of fuel oil consumption with great accuracy For horizontal installation in either a central oil supply or part of a one-pipe (suction pipe) system. Robust and durable construction Can be retrofitted to any existing heating system Not for outdoor use +/-1% accuracy 5 digit non-resettable totaliser perating temperature -5 c/+70 c IESEL K KERSENE Code escription Flow Rate (lph) Pressure (bar/psi) Boiler Capacity Inlet utlet Totaliser Fluids E0045 HZ3 il Meter * 6/ kW ¼ F BSP ¼ F BSP 0.01 to 1l 5 igit Totaliser AC *Calibrated to 0.18 to 12 +/-1% ACCURACY K KERSENE HZ5 il Meter Mechanical display meter to measure higher flow fuel oil consumption with great accuracy For installation in either a single or twin pipe system Robust and durable construction Can be retrofitted to any existing burner/heating system Not for outdoor use +/-1% accuracy 7 digit non-resettable totaliser perating temperature -5 c/+70 c Code escription Flow Rate (lph) Pressure (bar/psi) Boiler Capacity Inlet utlet Totaliser Fluids E0046 HZ5 il Meter / kW ⅛ F BSP ⅛ F BSP 0.01 to 1l 7 igit Totaliser AC E0046B HZ5 il Meter Wall Bracket E0046F 1/8" F BSP to 10mm Compression Converter ⅛" F BSP 10mm Compression 58

58 Mechanical Flow Meters \ Flow Meters IESEL K KERSENE il Tally Meter Mechanical display meter to measure heating oil consumption in domestic applications For horizontal or vertical installation 360 rotating display for easy use & installation Positive displacement /low pressure drop design Working temperature -10 c/+60 c +/-2% accuracy 7 digit non-resettable totaliser W WATER WRAS/WRC Approved Water Meter Mechanical display, single jet impeller meter to measure the quantity of cold water used For domestic, industrial & irrigation applications Can be installed horizontally or vertically Integral strainer & security tamper evident wire lock & seal Epoxy coated brass body & frost resistant dial Maximum temperature 30 c WRAS/WRC approved for drinking water Approved: EN A1+A2, IML R-49: 2006(E) MI MI-001 suited for secondary billing/sub metering Pulsar option (10ppl) - see table 1-50lph FLW RATE RANGE +/-2% ACCURACY Code escription Flow Rate (lph) Max Pressure (bar) Inlet utlet Totaliser Fluids E0052 il Tally Meter mm Compression 10mm Compression 7 igit Totaliser AC 1.5-5m³/h FLW RATE RANGE Single Jet IMPELLER Code escription Flow Range (m³/h) Max Pressure (bar) Inlet utlet Fluids WMSJ15 Alfa 15mm WRAS/WRC Cold Water Meter ½ M BSP ½ M BSP I WMSJ20 Alfa 20mm WRAS/WRC Cold Water Meter ¾ M BSP ¾ M BSP I WMSJ20PUL Alfa 20mm WRAS/WRC Cold Water Meter with Pulsar ¾ M BSP ¾ M BSP I 59

59 Flow Meters / igital Flow Meters K24 Aluminium K24 AdBlue 5-120lpm FLW RATE RANGE Code escription Flow Rate (lpm) Pressure (bar/psi) Inlet utlet c/w Socket Totaliser Fluids F K24 iesel Plastic M BSP 1 M BSP o 0.1 to igit Totaliser x10, x100 AI F K24 iesel Aluminium F BSP 1 M BSP 0.1 to igit Totaliser x10, x100 A F00408X00 K24 ATEX F BSP 1 M BSP 0.1 to igit Totaliser x10, x100 AGC F A K24 AdBlue M BSP 1 M BSP o 0.1 to igit Totaliser x10, x100 JIB F K24 1 F x F Socket 1" F BSP 1" F BSP iesel Chemical +/-1% ACCURACY See page 62 for pulsar versions RELATE PRUCTS lpm FLW RATE RANGE +/-5% ACCURACY Piusi K24 Flow Meter Turbine meter with digital display to measure the fluid dispensed & give flow rate indication Bi-directional to allow flow to be counted either way (only on aluminium & ATEX versions) Can be installed inline or by the delivery nozzle & display can be rotated in 4 different positions for easy reading +/-1% accuracy 5 digit partial totaliser & 6 digit totaliser Working temperature -10 c/+50 c LC display powered by two AAA batteries iesel, ATEX and AdBlue versions available Please note: Cattle Milk version is not for human consumption GPI Flow Meter Turbine meter with digital display to measure the quantity of fluid that has been dispensed Single channel reed switch Can be installed inline or by the delivery nozzle 4 digit totaliser Working temperature -10 c/+50 c Powered by two AAA batteries E0054 & E0056 aluminium body E0055 wetted parts - Stainless steel body/316 Stainless Steel/ Ceramic/Tungsten Carbide/PVF E0058 wetted parts - Nylon body/316 Stainless Steel/Ceramic/ Tungsten Carbide E0054 & E0055 are ATEX II 1 G EX 19 II c T6 certified Code escription Flow Rate (lpm) Max Pressure (bar) Inlet utlet Totaliser Accuracy Fluids E Aluminium GPI Meter - iesel F BSP 2 F BSP igital Totaliser +/-0.75% AP E Aluminium GPI Meter - iesel F BSP 1 F BSP igital Totaliser +/-5% AP E Stainless Steel GPI Meter F BSP 1 F BSP igital Totaliser +/-1% L E Nylon GPI Meter - Water F BSP 1 F BSP igital Totaliser +/-5% I IESEL IESEL W WATER C CHEMICAL P PETRL W WATER K KERSENE B1 B100 AB ABLUE WS WINSCREEN M CATTLE MILK 60

60 igital Flow Meters \ Flow Meters IESEL Code escription Flow Rate (lpm) Pressure (bar/psi) Viscosity (cst) Inlet/utlet Inlet Filter Totaliser Fluids K200 ml/l / ⅛ F BSP 0.1 to igit Totaliser AFHT K200 gr/kg kg/min 500/ ⅛ F BSP 0.1 to igit Totaliser K F K / ½ F BSP K400 - Windscreen / ½ F BSP F Next/ / ¾ F BSP 496A20 K600/3 - il / A00 K600/3 - iesel / IL Piusi val Gear Flow Meters val gear meter with digital display to measure the quantity of fluid that has been dispensed Flow rate indication (K600 & K900 models only) +/-0.5 accuracy 5 digit partial totaliser & 6 digit totaliser (4 digit partial on K200) Working temperature -10 c/+60 c Powered by two LR1 N-1.5v batteries Aluminium measuring chamber Single channel reed switch Range of models available depending upon performance requirements and fluid applications K900 GR GREASE K600 B/3 80mm isplay - iesel K600 B/3 80mm isplay - il WS WINSCREEN A ANTIFREEZE B2 B / ¾ F BSP Flanged 1 F BSP Flanged 1 F BSP Flanged 400µ 400µ 400µ / ¾ F BSP 400µ 49700A K600/ / K / K600 B/3 K600/4 1 ½ F BSP Flanged 3 F BSP Flanged lpm FLW RATE RANGE +/-0.5% ACCURACY See page 63 for pulsar versions RELATE PRUCTS 400µ 400µ Next/2 K600/3 K to igit Totaliser Plus x10, x to igit Totaliser Plus x10, x to igit Totaliser Plus x10, x to igit Totaliser Plus x10, x to igit Totaliser Plus x10, x to igit Totaliser Plus x10, x to igit Totaliser Plus x10, x to igit Totaliser Plus x10, x to igit Totaliser Plus x10, x100 AFHT F FHT A A F K200 AFHT AF 61

61 Flow Meters / Pulse Meters K24 ATEX K24 AdBlue Inline 90 egree 5-120lpm FLW RATE RANGE +/-1% ACCURACY See page 64 for remote displays RELATE PRUCTS 10-40lpm FLW RATE RANGE +/-1% ACCURACY Piusi K24 Pulse Meter Turbine meter to measure the quantity of fluid that has been dispensed c/w reed switch pulsar to send the information to an external management system or remote display Bi-directional to allow flow to be counted either way (aluminium body only) +/-1% accuracy Working temperature -10 c/+50 c 88 pulses per litre iesel, ATEX & AdBlue versions available Standard diesel version is constructed of plastic, whereas ATEX version is a more sturdy aluminium model Compatible remote displays available as an option Code escription Flow Rate (lpm) Pressure (bar/psi) Inlet utlet Socket Pulses (Per Litre) Material Fluids F A K24 Plastic Pulsar M BSP 1 M BSP o 88 Plastic AI F00408Y00 K24 ATEX Pulsar F BSP 1 M BSP 88 Aluminium AGC F B K24 AdBlue Pulsar M BSP 1 M BSP o 88 Plastic JI See page 64 for remote displays RELATE PRUCTS AB ABLUE W WATER Piusi Inline Turbinox Turbine meter to measure the quantity of fluid that has been dispensed c/w reed switch pulsar to send the information to an external management system or remote display +/-1% accuracy WS WINSCREEN Working temperature -10 c/+50 c 90 pulses per litre Inline and 90 degree versions available depending upon the installation Compatible remote displays available as an option Code escription Flow Rate (lpm) Pressure (bar/psi) Inlet utlet Pulses (Per Litre) Fluids F Inline Turbinox M BSP 1 M BSP 90 JI F egree Turbinox M BSP ¾ Hosetail 90 JI IESEL W WATER P PETRL K KERSENE AB ABLUE WS WINSCREEN 62

62 Pulse Meters \ Flow Meters IESEL IL GR GREASE Piusi val Gear Pulse Meters val gear meter to measure the quantity of fluid that has been dispensed C/w pulse output to send the information to an external management system or remote display +/-0.5% accuracy WS WINSCREEN Working temperature -10 c/+60 c Pulses per litre depending upon model Aluminium measuring chamber Range of models available depending upon performance requirements and fluid applications Compatible remote displays available as an option lpm FLW RATE RANGE +/-0.5% ACCURACY See page 64 for remote displays RELATE PRUCTS Code escription Flow Rate (lpm) Pressure (bar/psi) Viscosity (cst) Inlet/utlet Inlet Filter Pulses (Per Litre) Fluids K200HP / ⅛ F BSP 1400 AFKT K / ¼ F BSP 1400 AFT F K / ½ F BSP 100 AFHT 44007A K400 - Windscreen / ½ F BSP 100 H 472A20 K600/3 - il / ¾ F BSP Flanged 400µ 33 FHT 472A00 K900 K600/3 - iesel A ANTIFREEZE B2 B20 K600/4 K / K600/ / K / K / F BSP Flanged 1 ½ F BSP Flanged 2 F BSP Flanged 3 F BSP Flanged K400 K600/3 K200 K200HP 400µ 35 A 400µ 26 AFHT 400µ 14 AFHT 400µ 10 AFHT 63

63 Flow Meters / Pulse Meters 6-100lpm FLW RATE RANGE +/-0.5% ACCURACY igital ISPLAY TYPE Piusi K600 B/3 Pulse Meter val gear meter to measure the quantity of fluid that has been dispensed c/w pulse output to send the information to an external management system or remote display 80mm rotatable digital display eliminating the need for a remote display to view transactions at the dispensing point Variable pulse ratio for connecting to any management system 5 digit partial totaliser, 6 digit totaliser & flow rate indication +/-0.5% accuracy Powered by two LR1 N-1.5v batteries Working temperature -10 c/+50 c Code escription Flow Rate (lpm) Pressure (bar/psi) Inlet utlet Pulses (Per Litre) Totaliser Fluids K600 B/3 Pulsar - iesel K600 B/3 Pulsar - il / /994 1 F BSP Flanged ¾ F BSP Flanged All Piusi METER TYPE See page 64 for pulse meters RELATE PRUCTS 1 F BSP Flanged ¾ F BSP Flanged 1, 2, 10, 20, 50, 100 1, 2, 10, 20, 50, 100 Piusi Remote isplay Large digital display to allow the user to see the quantity dispensed Calibration function 0.1 to igit Totaliser Plus x 10, x to igit Totaliser Plus x 10, x digit non-resettable totaliser, 6 digit totaliser & flow rate indication 1, 2, 10, 20, 50, 100 pulses per litre Low battery indication; 2 x AA batteries Basic display only versions or model with a pulse emitter to connect to other types of systems Range of models depending upon the pulse meter that the display is to be used in conjunction with (max cable length 15m) Code escription Type Meter Totaliser Batteries F A Remote isplay for K600 Pulse UT K600 iesel 0.1 to igit Totaliser Plus x 10, x x AA 1.5v F A Remote isplay for K600/4 Pulse UT K600/4 0.1 to igit Totaliser Plus x 10, x x AA 1.5v F A Remote isplay for K700 Pulse UT K to igit Totaliser Plus x 10, x x AA 1.5v F Universal Remote isplay Pulse ut Pulse UT All Piusi Pulse Meters 0.1 to igit Totaliser Plus x 10, x x AA 1.5v F Universal Remote isplay Pulse In Pulse IN All Piusi Pulse ut 0.1 to igit Totaliser Plus x 10, x x AA 1.5v F B Remote isplay AdBlue Pulse UT Turbinox / K to igit Totaliser Plus x 10, x x AA 1.5v IESEL ANY FLUI IL A F 64

64 Contents \ Hoses & Reels HSES & REELS ELIVERY HSES SUCTIN HSES HSE REELS HEATING IL LINES 78 SUCTIN ELIVERY HEATING LINES 78 HSE REELS

65 Hoses & Reels / elivery Hoses 25mm HSE I 6m MAX LENGTH IESEL IL K KERSENE Gravity/Pump iesel elivery Hose iesel delivery hose for gravity & low pressure pumping systems iesel/oil resistant construction Anti-static soft wall with NBR cover Synthetic textile yard reinforcement Anodised aluminium BSPT hose tails & ring ferrules Temperature -25 c/+70 C ifferent lengths available depending on requirements Please note: Same hose as premium assemblies but with different hose ends & ferrules Code escription Length (m) Hose I (mm) Hose (mm) Max Pressure (bar) Hose Tails Fluids AB iesel elivery Hose 3m M BSPT AFC AB iesel elivery Hose 4m M BSPT AFC AB iesel elivery Hose 5m M BSPT AFC AB iesel elivery Hose 6m M BSPT AFC 19-25mm HSE I 60m MAX LENGTH Premium Gravity/Pump iesel elivery Hose iesel delivery hose for gravity & low pressure pumping systems iesel/oil resistant construction Anti-static soft wall with NBR cover Synthetic textile yard reinforcement Premium assemblies c/w swaged stainless steel full ferrules & 1 M BSP hose tails with sealing o rings ifferent lengths available depending on requirements (¾ assemblies available on request) Code escription Length (m) Hose I (mm) Hose (mm) Max Pressure (bar) Hose Tails Fluids EL iesel elivery Hose 3m M BSP AFC EL iesel elivery Hose 4m M BSP AFC EL iesel elivery Hose 5m M BSP AFC EL iesel elivery Hose 6m M BSP AFC EL iesel elivery Hose Per Metre Max AFC EL iesel elivery Hose 50m Coil AFC EL1051 ¾ iesel elivery Hose Per Metre Max AFC EL1050 ¾ iesel elivery Hose 60m Coil AFC IESEL IL K KERSENE 66

66 elivery Hoses \ Hoses & Reels IESEL K KERSENE iesel Gravity Hose Kits Cost effective, ready-made solution for dispensing diesel from gravity-fed storage tanks 1 M BSPT aluminium hose tails & ring ferrules Piusi Self 2000 aluminium manual nozzle 1 M x F locking angle valve (padlock not supplied) Supplied in plastic labelled bag ifferent lengths available depending on requirements K KERSENE Premium iesel Gravity Hose Kits Cost effective, ready-made solution for dispensing diesel from gravity-fed storage tanks Hose c/w swaged stainless steel full ferrules & 1 M BSP hose tails with sealing o rings Piusi Self 2000 aluminium manual nozzle 1 M x F locking angle valve (padlock not supplied) PTFE tape supplied as standard Supplied in clip close bag with carry handle & info sheet Customer branding options available ifferent hose lengths available depending on requirements 25mm HSE I 6m MAX LENGTH Code escription Hose Length (m) Hose I (mm) Hose (mm) Inlet Fluids AB2250 3m Gravity Hose Kit Locking Angle Valve AFC AB2251 4m Gravity Hose Kit Locking Angle Valve AFC AB2252 5m Gravity Hose Kit Locking Angle Valve AFC AB2253 6m Gravity Hose Kit Locking Angle Valve AFC IESEL IL IL 25mm HSE I 6m MAX LENGTH Code escription Hose Length (m) Hose I (mm) Hose (mm) Inlet Fluids AB3350 3m Premium Gravity Hose Kit Locking Angle Valve AFC AB3079 4m Premium Gravity Hose Kit Locking Angle Valve AFC AB3080 5m Premium Gravity Hose Kit Locking Angle Valve AFC AB3081 6m Premium Gravity Hose Kit Locking Angle Valve AFC 67

67 Hoses & Reels / elivery Hoses 19-25mm HSE I 80m MAX LENGTH 19-25mm HSE I 6m MAX LENGTH IESEL Parker Carbopress iesel elivery Hose iesel delivery hose for low pressure pumping systems Usually supplied as standard on Piusi pump kits e.g. Cube, ST & rum range Anti-static NBR/EPM rubber cover Synthetic textile yarn reinforcement Swaged 1 M BSP fittings plus sealing 'o' rings Temperature -25 C/+80 C ifferent lengths available depending on requirements P PETRL IL IESEL K KERSENE Code escription Length (m) Hose I (mm) Hose (mm) Max Pressure (bar) Hose Tails Fluids 8976 ¾ Parker iesel elivery Hose 4m M BSP AFC ¾ Parker iesel elivery Hose 6m M BSP AFC Parker iesel elivery Hose 4m M BSP AFC F Parker iesel elivery Hose 6m M BSP AFC F APM ¾ Parker iesel elivery Hose Per Metre AFC F APM 1" Parker iesel elivery Hose Per Metre AFC F A ¾ Parker iesel elivery Hose 80m Coil AFC F A 1" Parker iesel elivery Hose 40m Coil AFC F ¾ Parker Petrol elivery Hose 4m " M BSP GAFC Goodyear Petrol elivery Hose elivery hose designed for petrol & fuel dispensing systems Chemigum rubber tube & steel wire braid reinforcement Crush, abrasion & weather resistant Tested & approved to EN1360 Plated mild steel couplings c/w sealing gaskets Temperature -25 C/+88 C ifferent lengths available depending on requirements Code escription Length (m)/(ft) Hose I (mm) Hose (mm) Max Pressure (bar) Hose Tails Fluids AB3077 ¾ Petrol elivery Hose 10ft 3.05/ ¾ M BSP GAP AB3078 ¾ Petrol elivery Hose 12ft 3.66/ ¾ M BSP GAP AB3076 ¾ Petrol elivery Hose 15ft 4.57/ ¾ M BSP GAP AB3075 ¾ Petrol elivery Hose 20ft 6.10/ ¾ M BSP GAP AB Petrol elivery Hose 10ft 3.05/ M BSP GAP AB Petrol elivery Hose 12ft 3.66/ M BSP GAP AB Petrol elivery Hose 15ft 4.57/ M BSP GAP AB Petrol elivery Hose 20ft 6.10/ M BSP GAP B1 B100 P PETRL 68

68 elivery Hoses \ Hoses & Reels AB ABLUE Piusi AdBlue elivery Hose elivery hose for AdBlue pump installations Supplied as standard with the Piusi AdBlue IBC kits EPM inner tube & outer cover c/w textile synthetic reinforcement Abrasion & weather resistant Temperature -30 C/+100 C Available to order by the metre or in coils AB ABLUE AdBlue elivery Hose elivery hose for manual AdBlue pump installations Supplied as standard in the manual AdBlue pump kits PVC/119 inner tube & PVC/702 outer cover Temperature -16 C/+60 C Available to order by the metre or in coils AB ABLUE W WATER W WATER C CHEMICAL 19mm HSE I 80m MAX LENGTH Code escription Length (m) Hose I (mm) Hose (mm) Max Pressure (bar) Fluids F PMTR AdBlue pen Ended elivery Hose Per Metre Max JIL F AdBlue pen Ended elivery Hose 80m Coil JIL C CHEMICAL Continental 2 AdBlue elivery Hose elivery hose for bulk dispensing into & out of AdBlue tanks Pliosyn UHMWPE inner tube & EPM cover Spiral-plied synthetic fabric with double wire helix reinforcement Temperature -40 C/+66 C Meets IS standards for quality, safety & contamination Available to order by the metre or in coils 19mm HSE I 50m MAX LENGTH Code escription Length (m) Hose I (mm) Hose (mm) Max Pressure (bar) Fluids AB1055 AdBlue pen Ended elivery Hose Per Metre Max JIL AB AdBlue pen Ended elivery Hose 50m Coil JIL W WATER C CHEMICAL 50.8mm HSE I 30.5m MAX LENGTH Code escription Length (m) Hose I (mm) Hose (mm) Max Pressure (bar) Fluids AB AdBlue elivery Hose Per Metre Max JIL AB AdBlue elivery Hose 30m Coil JIL 69

69 Hoses & Reels / elivery Hoses 19mm HSE I 4m MAX LENGTH 19mm HSE I 4m MAX LENGTH ½" M BSP INLET 4m MAX LENGTH AB ABLUE Premium AdBlue Gravity Hose Kit Ready-made solution for dispensing AdBlue from a bottom outlet, gravity-fed IBC ¾ swaged EPM AdBlue delivery hose Piusi Suzzara Blue manual nozzle 60 x 6 IBC bottom adaptor & 1 F x F cam fitting Camlock coupling configuration allows the hose assembly to be easily removed from the IBC for added security Polypropylene hose tail & stainless steel clamp rings ifferent lengths available depending on requirements Code escription Hose Length (m) Hose I (mm) Hose (mm) Inlet Fluids A-ELKIT3 3m AdBlue Gravity Hose Kit Thread 60 x 6 JIL A-ELKIT4MTR 4m AdBlue Gravity Hose Kit Thread 60 x 6 JIL Clear version AB ABLUE Self Assembly AdBlue Gravity Hose Kit Simple solution for dispensing AdBlue from a bottom outlet gravity-fed IBC Two versions; one with clear spiral hose & one with black EPM Piusi manual nozzle supplied with hose tail inlet c/w stainless steel hose clips & 60 x 6 IBC fittings Kits supplied in 3m or 4m lengths - other lengths upon request Code escription Hose Length (m) Hose I (mm) Hose (mm) Inlet Fluids AB2230 Clear Self Assembly AdBlue Gravity Hose Kit 3m Thread 60 x 6 JIL AB2231 Clear Self Assembly AdBlue Gravity Hose Kit 4m Thread 60 x 6 JIL AB2232 Black Self Assembly AdBlue Gravity Hose Kit 3m Thread 60 x 6 JIL AB2233 Black Self Assembly AdBlue Gravity Hose Kit 4m Thread 60 x 6 JIL Lube il elivery Hose elivery hose designed for the dispensing of lubrication oil Used primarily in automotive, industrial & agricultural applications Female fittings are swivel coned & male fittings are coned BSP Hose type R1 AT rubber ifferent lengths available depending on requirements Code escription Length (m) Inlet utlet Max. Pressure (bar) Fluids VH9203 ½ Lube il elivery Hose 2m 2 ½ M BSP ½ F BSP 60 F VH9204 ½ Lube il elivery Hose 4m 4 ½ M BSP ½ F BSP 60 F IL W WATER W WATER C CHEMICAL C CHEMICAL 70

70 Suction Hoses \ Hoses & Reels IESEL Plutone iesel/il Suction Hose Sturdy & durable suction hose for fuel pump installations (can also be used as delivery hose) Strong PVC/NBR inner layer iesel resistant - can be submerged Shock resistant harmonic steel wire & polyester yarn reinforcement Crush, abrasion & weather resistant Temperature range -30 c/+80 c Available in an assembly, open ended per metre or special electrically continuous assembly IESEL IL IL W WATER 19-25mm HSE I 60m MAX LENGTH Code escription Length (m) Hose I (mm) Hose (mm) Max Pressure (bar) Hose Tails Fluids PSH001 1 Plutone Suction Hose 1m M BSP AFI PSH002 1 Plutone Suction Hose 1.5m M BSP AFI PSH003 1 Plutone Suction Hose 2m M BSP AFI PSH004 1 Plutone Suction Hose 3.5m M BSP AFI PSH000 1 Plutone Suction Hose Per Metre Max AFI PSH34 ¾ Plutone Suction Hose Per Metre Max AFI PSH " Plutone Suction Hose 60m Coil AFI PSH " Plutone Suction Hose 30m Coil AFI PSH34.30 ¾ Plutone Suction Hose 30m Coil AFI W WATER K KERSENE Vacupress iesel/il Suction Hose Sturdy & durable suction hose for fuel pump installations (can also be used as delivery hose) Strong & flexible PVC-PU Nitrilic rubber alloy iesel resistant cover - can be submerged Steel wire helix & polyester yarn reinforcement Crush, abrasion & weather resistant Temperature range -25 c/+55 c B1 B100 Available in an assembly, open ended per metre or special electrically continuous assembly Hose only & assemblies also available in ¾, 1 ¼, 1 ½ and 2" 25mm HSE I 60m MAX LENGTH Code escription Length (m) Hose I (mm) Hose (mm) Max Pressure (bar) Hose Tails Fluids VSH001 1 Vacupress Suction Hose 1m M BSP AFICP VSH002 1 Vacupress Suction Hose 1.5m M BSP AFICP VSH003 1 Vacupress Suction Hose 2m M BSP AFICP VSH004 1 Vacupress Suction Hose 3.5m M BSP AFICP VSH000 1 Vacupress Suction Hose Per Metre Max AFICP VSH Vacupress Suction Hose 60m Coil AFICP VSH Vacupress Suction Hose 30m Coil AFICP 71

71 Hoses & Reels / Suction Hoses 25-50mm HSE I 50m MAX LENGTH IESEL IL iesel/il Suction Hose General suction hose for low pressure fuel pump installations (can also be used as delivery hose) Strong & flexible black PVC with 25% NBR Shock resistant galvanised spiral Crush, abrasion & weather resistant Available as assemblies per metre or in coils Code escription Max Length (m) Hose I (mm) Hose (mm) Max Pressure (bar) Fluids AB3100 1" Suction Hose Per Metre AFI AB3101 2" Suction Hose Per Metre AFI AB " Suction Hose 50m Coil AFI AB " Suction Hose Coil AFI 19-25mm HSE I 30m MAX LENGTH See page 73 for other AdBlue hoses RELATE PRUCTS IESEL IL W WATER Clear iesel/il/water Suction Hose General suction hose for pump and gravity installations (can also be used as a delivery hose) Transparent hose wall for visual indication of flow Strong & flexible PVC construction Shock resistant harmonic steel wire Temperature range -5 c/+60 c ¾ version popular for AdBlue applications Available per metre order as required Code escription Max Length (m) Hose I (mm) Hose (mm) Max Pressure (bar) Fluids AB5001 ¾ Suction Hose Per Metre AFIJ AB Suction Hose Per Metre AFIJ Plastic Metal 1.1m MAX LENGTH rums USE WITH IESEL IL W WATER P PETRL AB ABLUE Piusi Suction Tubes Telescopic suction downtube designed for dispensing from drums 1 M BSP threaded inlet K KERSENE AB ABLUE Plastic version for multi-fluid applications & metal version that is compatible for use with flammable liquids such as petrol Code escription Material rum Connection Length Fluids Telescopic Suction Tube Plastic 1 BSP 535mm-1000mm AFJI F Metal Telescopic Suction Tube Metal 1 BSP 650mm mm AFGC W WATER 72

72 Suction Hoses \ Hoses & Reels AB ABLUE Piusi AdBlue Suction Hose Suction hose for AdBlue pump installations Supplied as standard with the Piusi AdBlue IBC kits (1.5m length) Anti-static & sulphur free EPM rubber compound Synthetic textile fabric with embedded steel wire helix Temperature -40 C/+100 C Can be submerged with suitable hose ends Available in an assembly or open ended per metre AB ABLUE Piusi AdBlue IBC/rum Suction Tube 2-part suction downtube for dispensing from AdBlue IBCs & drums CS/SEC plug head for connecting to a CS connector for example the Piusi SEC BSP or Trisure versions available depending upon the IBC or drum inlet connection AB ABLUE W WATER C CHEMICAL Piusi IBC Bottom utlet Kits esigned for connecting bottom outlet IBCs to the suction side of the pumping system IBC adaptor with 60 x 6 threads, 0.3m suction hose & check valve External suction hose kit has 1.1m of additional hose after the check valve for connecting to the pump Bottom connection kit is designed for when you already have a suction hose 19mm HSE I 40m MAX LENGTH Code escription Length (m) Hose I (mm) Hose (mm) Max Pressure (bar) Fluids F PMTR AdBlue Suction Hose Per Metre Max JIL F AdBlue Suction Hose 40m Coil JIL 1.05m MAX LENGTH rums/ibcs USE WITH Code escription IBC Connection Plug Head Length Fluids F IBC Suction Tube Trisure Trisure 56 x 4 Male CS/SEC 1050mm J F IBC Suction Tube 2 BSP 2 BSP CS/SEC 1050mm J 60x6 INLET ¾ UTLET Code escription Inlet utlet Length Check Valve Fluids F IBC External Suction Hose Thread 60 x 6 ¾ Hose 1.5m o J F IBC Bottom Connection Kit Thread 60 x 6 ¾ Hose Tail 0.3m o J Connection Kit Suction Hose 73

73 Hoses & Reels / Hose Reels See below for mounting plates RELATE PRUCTS Code escription Hose Length (m) 15m MAX HSE CAPACITY ¾ or 1" HSE SIZE Max Hose Length (m) Most Piusi REEL TYPE Wall MUNTING Max Pressure (bar) IESEL Piusi iesel Hose Reels Automatic hose reels designed for low pressure diesel pumping systems including refuelling applications Sturdy steel structure for heavy duty conditions Protected latch mechanism to prevent injury to the hands Reduced pressure loss through correct sizing of the hydraulics Adjustable arm brackets for easy positioning ¾ or 1 models supplied bare or with a choice of hose lengths Bare reel c/w hose clamp, protection spring & hose stop ANY FLUI Inlet utlet Pressure Loss (bar) F ¾" Empty Hose Reel 9.5m SMALL M BSP Swivel ¾ Hose Barb 60lpm A F ¾" Empty Hose Reel 14m M BSP Swivel ¾ Hose Barb 60lpm A F " Empty Hose Reel 10m M BSP Swivel 1 Hose Barb 80lpm A F " Empty Hose Reel 15m XL F BSP Swivel 1 Hose Barb 80lpm A F ¾" Hose Reel c/w 8m SMALL F BSP Swivel 1 M BSP 60lpm A F ¾" Hose Reel c/w 10m F BSP Swivel 1 M BSP 60lpm A F ¾" Hose Reel c/w 14m F BSP Swivel 1 M BSP 60lpm A F " Hose Reel c/w 8m F BSP Swivel 1 M BSP 80lpm A F " Hose Reel c/w 10m F BSP Swivel 1 M BSP 80lpm A AB2270 1m Whip Hose 1m 10 1" M BSP 1" M BSP A AB m Whip Hose 1.5m 10 1" M BSP 1" M BSP A AB2272 2m Whip Hose 2m 10 1" M BSP 1" M BSP A Fixed Plate Rotating Plate Fluids Piusi Hose Reel Support Plates ptional support plates designed for the sturdy wall mounting of Piusi hose reels Fixed support plate is a cost effective mounting solution when the hose reel is not required to be rotated Rotating support plate is designed for applications where the direction of the hose reel needs to be flexible Small plate models designed for use with Piusi hose reels marked SMALL in the product table Code escription Type Hose Reel Models F Fixed Support Plate Fixed For all Piusi hose reels (excl. SMALL & XL) F Fixed Support Plate - Small Fixed For hose reels marked SMALL F Rotating Support Plate Rotating For all Piusi hose reels (excl. SMALL & XL) F Rotating Support Plate - Small Rotating For hose reels marked SMALL 74

74 Hose Reels \ Hoses & Reels IESEL 15m High Capacity iesel Hose Reel Automatic hose reel for low pressure diesel pumping systems including refuelling applications Thanks to length of hose they are ideal for where the vehicle being refuelled cannot easily reach the fuelling station Anti-static hose with an anti-kink spring at the nozzle end Sturdy steel structure, 4 way rollers & hose stop Hose arms can be fixed in three different positions 1" M BSP outlet for easy dispensing nozzle connection, which is uncommon on larger reels where conical fittings are often used ANY FLUI High Capacity Hose Reels Automatic bare hose reel for mutli-prupose applications where a longer hose length is needed Spring rewind sturdy mild steel structure for heavy duty conditions Twin pedestal design to enhance performance & reliability Accessible flow path for easy hose installation 4 roller guide to prolong hose length with adjustable hose arms Externally mounted swivel assembly for easy maintenance Suitable for wall, floor, ceiling & vehicle mounting ATEX approved to II 94/9 IIB 2 G c T4 T135 C X 15m MAX HSE CAPACITY Code escription Max 1 Hose Length (m) Max ¾ Hose Length (m) Max Pressure (bar) Inlet utlet Fluids CTS2066 High Capacity Hose Reel F BSP 1 F BSP N CTS2067 High Capacity Hose Reel - Larger F BSP 1 F BSP N 1" HSE SIZE Code escription Hose Length (m) Max Pressure (bar) Inlet utlet Fluids HRHC2515 1" High Capacity Hose Reel c/w 15m 15m 10 1 F BSP Swivel 1 M BSP A AB2270 1m Whip Hose 1m 10 1" M BSP 1" M BSP A IESEL 25m & 30m High Capacity iesel Reels Automatic hose reel for low pressure diesel pumping systems including refuelling applications c/w 1m of whip hose Thanks to the length of hose they are ideal for where the vehicle being refuelled cannot easily reach the fuelling station Anti-static hose with an anti-kink spring at the nozzle end Sturdy steel structure, 4 way rollers & hose stop Hose arms can be fixed in three different positions 1" M BSP outlet for easy dispensing nozzle connection, which is uncommon on larger reels where conical fittings are often used See page 76 for reels for other fluids RELATE PRUCTS 30m MAX HSE CAPACITY 1" HSE SIZE See page 76 for reels for other fluids RELATE PRUCTS Code escription Hose Length (m) Max Pressure (bar) Inlet utlet Fluids HRHC2525 1" High Capacity Hose Reel c/w 25m 25m 10 1 F BSP Swivel 1 M BSP A HRHC2530 1" High Capacity Hose Reel c/w 30m 30m 10 1 F BSP Swivel 1 M BSP A 30m 1" MAX HSE CAPACITY 40m 3/4" MAX HSE CAPACITY 75

75 Hoses & Reels / Hose Reels ANY FLUI Stainless High Capacity Hose Reels Automatic bare hose reel for multipurpose applications where a longer hose length is needed Sturdy stainless steel AISI 304 structure for heavy duty conditions Twin pedestal design to enhance performance & reliability Adjustable arm brackets for easy positioning Twin spring design 20mm I inlet swivel joint & Viton seals Conical 1 M BSP inlet/outlet threads Code escription Max 1 Hose Length (m) Max ¾ Hose Length (m) Max Pressure (bar) Inlet utlet Fluids CTS2064 Stainless Steel High Capacity Hose Reel M BSP 1 M BSP N CTS2065 Stainless Steel High Capacity Hose Reel - Larger M BSP 1 M BSP N See page 74 for mounting plates RELATE PRUCTS 30m 1" MAX HSE CAPACITY 30m 3/4" MAX HSE CAPACITY 15m MAX HSE CAPACITY ¾" HSE SIZE AB ABLUE Piusi AdBlue Hose Reels Automatic hose reel designed for low pressure AdBlue pumping Protected latch mechanism to prevent injury to the hands Reduced pressure loss through correct sizing of the hydraulic system Adjustable arm brackets for easy positioning Hose stop for locking at the chosen length Supplied either bare or complete with a choice of hose length Bare reel c/w hose fastening clamp & protection spring Code escription Hose Length (m) Max Hose Length (m) Max Pressure Inlet utlet Pressure Loss Fluids F AdBlue Empty Reel SMALL bar ¾ Swivel Hose Barb ¾ Hose Barb 35lpm JIL F AdBlue Reel c/w 8m SMALL 8 10 bar ¾ Swivel Hose Barb ¾ pen Hose 35lpm JIL F AdBlue Reel c/w 15m bar ¾ Swivel Hose Barb ¾ pen Hose 35lpm JIL See page 74 for mounting plates RELATE PRUCTS 15m MAX HSE CAPACITY ¼" or 3 /8" HSE SIZE GR GREASE W WATER C CHEMICAL Piusi Grease Hose Reels Automatic hose reels designed for high pressure grease dispensing systems in garage & workshop applications Sturdy steel structure for heavy duty conditions Rachet to prevent lockup when hose is completely extended 4 way rollers to facilitate the unrolling, avoiding friction than can cause wear to the hose Hose stop for locking at the chosen length Adjustable arm brackets for easy positioning Code escription Hose Length (m) Max Hose Length (m) Max Pressure (bar) Inlet utlet Pressure Loss (bar) Fluids HN ¼ Empty Reel 15m SMALL ¼ F BSP Swivel ¼ M BSP K HN ⅜ Empty Reel 15m SMALL ⅜ F BSP Swivel ⅜ M BSP K HA ¼ Reel c/w 15m SMALL ¼ F BSP Swivel ¼ M BSP 600 gr/min K HA ⅜ Reel c/w 15m SMALL ⅜ F BSP Swivel ⅜ F BSP 600 gr/min K 76

76 Hose Reels \ Hoses & Reels IL Piusi il Hose Reels Automatic open or closed hose reels designed for high pressure oil dispensing systems in garage & workshop applications Sturdy steel structure for heavy duty conditions Rachet to prevent lockup when hose is completely extended 4 way rollers to facilitate the unrolling, avoiding friction than can cause wear to the hose Hose stop for locking at the chosen length Adjustable arm brackets for easy positioning (open models only) Range of models supplied bare or with a choice of hose lengths Closed reel c/w a fixed support plate AIR AIR W WATER Piusi Air & Water Hose Reels Automatic open or closed hose reels designed for professional air use in garage & workshop environments Also compatible for use for commercial water dispensing applications Compact yet sturdy steel structure for heavy duty conditions Polyurethane hose reinforced with textile braid Protected latch mechanism to prevent injury to the hands 4 way rollers to facilitate unrolling, avoiding friction than can cause wear to the hose Hose stop for locking at the chosen length Easy & versatile installation through bracket pivots 20m MAX HSE CAPACITY ½" or 3 /8" HSE SIZE See page 74 for mounting plates RELATE PRUCTS 15m MAX HSE CAPACITY ½" or 3 /8" HSE SIZE See page 74 for mounting plates RELATE PRUCTS Code escription Hose Max Hose Max Pressure Inlet utlet Pressure Fluids Length (m) Length (m) (bar) Loss (bar) HN ½ pen Empty Hose Reel 15m SMALL ½ M BSP Swivel ½ M BSP 60 Cone Seat F HN ⅜ pen Empty Hose Reel 15m SMALL ⅜" F BSP Swivel ⅜" F BSP 60 Cone Seat F HN ½ pen Empty Hose Reel 20m ½ M BSP Swivel ½ M BSP 60 Cone Seat F HA ½ pen Hose Reel c/w 10m SMALL ½ M BSP Swivel ½ M BSP 60 Cone Seat 30lpm F HA ½ pen Hose Reel c/w 15m SMALL ½ M BSP Swivel ½ M BSP 60 Cone Seat 30lpm F HA ½ pen Hose Reel c/w 20m ½ M BSP Swivel ½ M BSP 60 Cone Seat 30lpm F HC ½ Closed Hose Reel c/w 12m ½ M BSP Swivel ½ M BSP 60 Cone Seat 30lpm F Code escription Hose Length (m) Max Pressure (bar) Inlet utlet Fluids HA ½ pen Hose Reel c/w 15m SMALL ½ M BSP Swivel ½ M BSP Hose Barb EI HA ⅜ pen Hose Reel c/w 15m SMALL ⅜ F BSP Swivel ½ F BSP Hose Barb EI HC A 10x14 Closed Hose Reel c/w 12m mm BSP Swivel ¾ M BSP Hose Barb EI HC A 8x12 Closed Hose Reel c/w 15m mm BSP Swivel ¼ M BSP Hose Barb EI pen Closed pen Closed 77

77 Hoses & Reels / Heating il Lines Braided TYPE 1000mm MAX LENGTH Long Life TYPE 900mm MAX LENGTH K KERSENE Braided Flexible il Line Braided flexible oil line for connecting pipework to the oil boiler of a heating oil system Inner hose is constructed of UNI9362 nitrile rubber uter braid is constructed of galvanised steel mesh complient with ANCC standards Mechanically crimped connection ends Temperature range: -25 C to 90 C ifferent lengths & inlet/outlet fittings available depending upon individual installation Code escription Length (mm) Inlet utlet Tube Type Fluids FL4001 il Line MEC ¼ F (90 Elbow) x ¼ F 900mm 900 ¼ F BSP 90 Elbow ¼ F BSP Braided CFAM FL4002 il Line MEC ¼ M (90 Elbow) x 3 8 F 900mm 900 ¼ M BSP 90 Elbow ⅜ F BSP Braided CFAM FL4003 il Line ¼ F (90 Elbow) x ¼ M 500mm 500 ¼ F BSP 90 Elbow ¼ M BSP Braided CFAM FL5003 il Line ¼ F x ¼ F 750mm 750 ¼ F BSP ¼ F BSP Braided CFAM FL5004 il Line ¼ F x ¼ F 1000mm 1000 ¼ F BSP ¼ F BSP Braided CFAM K KERSENE IL IL Long Life Flexible il Line Long life flexible oil line for connecting pipework to the oil boiler of a heating oil system urable, flexible and resistant against sunlight & the environment Thermoplastic & rubber versions available Anti-kink & wipe clean (thermoplastic only) ifferent inlet/outlet fittings available depending upon individual installation Code escription Length (mm) Inlet utlet Tube Type Fluids FL8040 il Line MEC ¼ F (90 Elbow) x ¼ F 900mm 900 ¼ F BSP 90 Elbow ¼ F BSP Thermoplastic CFAM FL8041 il Line MEC ¼ M (90 Elbow) x ⅜ F 900mm 900 ¼ M BSP 90 Elbow ⅜ F BSP Thermoplastic CFAM FL8043 il Line ¼ M (90 Elbow) x ¼ F 900mm 900 ¼ M BSP 90 Elbow ¼ F BSP Thermoplastic CFAM FL8068 il Line ¼ F (90 Elbow) x ¼ M 900mm 900 ¼ F BSP 90 Elbow ¼ M BSP Thermoplastic CFAM FL7154 il Line ¼ F x ¼ F 900mm 900 ¼ F BSP ¼ F BSP Thermoplastic CFAM FL7040 il Line MEC ¼ F (90 Elbow) x ¼ F 900mm 900 ¼ F BSP 90 Elbow ¼ F BSP Rubber CFAT FL7041 il Line MEC ¼ M (90 Elbow) x ⅜ F 900mm 900 ¼ M BSP 90 Elbow ⅜ F BSP Rubber CFAT FL7043 il Line ¼ M (90 Elbow) x ¼ F 900mm 900 ¼ M BSP 90 Elbow ¼ F BSP Rubber CFAT FL7068 il Line ¼ F (90 Elbow) x ¼ M 900mm 900 ¼ F BSP 90 Elbow ¼ M BSP Rubber CFAT IESEL IESEL B3 B30 B3 B30 B2 B20 78

78 Contents \ Nozzles NZZLES FUEL LUBE IL GREASE ABLUE LUBE IL FUEL ABLUE GREASE

79 Nozzles / Fuel Nozzles See page 83 for nozzle holsters ACCESSRIES See page 83 for nozzle holsters ACCESSRIES 120lpm MAX FLW RATE Manual TYPE Piusi Self 2000 Manual Nozzle For diesel/oil dispensing in low & high flow rate conditions Cost effective solution for pump & gravity systems ie cast aluminium body c/w removable lever protection Integral hook for hanging nozzle without a holster Available with 1 F BSP Swivel or 1 Hose Tail Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Seal Material Inlet Connection Fluids Piusi Self 2000 F Swivel HNBR 1 F BSP Swivel AF Piusi Self 2000 Hose Tail HNBR 1 Hose Tail AF 150lpm MAX FLW RATE Manual TYPE 80lpm MAX FLW RATE Manual TYPE IESEL IESEL Piusi Self 3000 Manual Nozzle For diesel/oil dispensing at higher flow & pressure than Self 2000 Cost effective solution for pump & gravity systems Aluminium body with plastic anti-shock handle protector Integral hook for hanging nozzle without a holster ATEX version available with no latch for use in flammable environments IESEL IL IL IL P PETRL W WATER Piusi Plastic Manual Nozzle For the dispensing of diesel, oil, water & other fluids Economy model for pump & gravity systems Polypropylene body K KERSENE Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Seal Material Inlet Connection Fluids Piusi Self 3000 F Swivel HNBR 1 F BSP Swivel AF 65001A Piusi Self 3000 F Swivel Unleaded HNBR 1 F BSP Swivel AF 65003A Piusi Self 3000 ATEX HNBR 1 F BSP Swivel AGC C CHEMICAL Integral hook for hanging nozzle without a holster Available with 1 F BSP Swivel or 1 Hose Tail Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Seal Material Inlet Connection Fluids Piusi Plastic Nozzle - S Viton 1 F BSP AFIL F Piusi Plastic Nozzle - F Viton 1 Hose Tail AFIL 80

80 Fuel Nozzles \ Nozzles IESEL ZVA 19 Manual Nozzle For diesel dispensing in low & high flow rate conditions High quality, heavy duty model from well known ZVA brand ie cast aluminium construction Version specifically for pump installations and version for gravity systems available Versions available for diesel & chemicals IESEL B1 B100 Highspeed Manual Nozzle For high flow refuelling of large vehicles & heavy plant and agricultural machinery esigned for both pump & gravity systems Heavy duty cast aluminium body Integral hook for hanging nozzle without a holster Available with or without swivel K KERSENE A Tanker Manual Nozzle For high flow delivery of heating oil & diesel usually to refill a storage tank Fitted to a fuel tank delivery hose with anti-drain valve for wet hose systems Heavy duty cast aluminium body 2 swivel lugged outlet with removable spout 100lpm MAX FLW RATE Manual Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Seal Material Inlet Connection Fluids PF5012 ZVA 19 iesel Gravity Nozzle NBR 1 F BSP A PF5014 ZVA 19 iesel Pump Nozzle NBR 1 F BSP A PF5013 ZVA 19 Chemical Gravity Nozzle PTFE 1" F BSP L PF5025 ZVA 19 - Chemical Pump Nozzle PTFE 1" F BSP L TYPE 250lpm MAX FLW RATE Manual Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Seal Material Inlet Fluids PF5018 High Speed Manual Nozzle Viton & Graphite 1 ½ F BSP AP PF5018S High Speed Manual Nozzle c/w Swivel Viton & Graphite 1 ½ F BSP Swivel AP IESEL C CHEMICAL B1 B100 TYPE 415lpm MAX FLW RATE Manual Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Seal Material Inlet Fluids PF3060 A Tanker Nozzle Viton 1 ½ F BSP Swivel APC TYPE See page 83 for nozzle holsters ACCESSRIES 81

81 Nozzles / Fuel Nozzles See page 83 for nozzle holsters ACCESSRIES See page 83 for nozzle holsters ACCESSRIES 120lpm MAX FLW RATE Auto TYPE 80lpm MAX FLW RATE Auto TYPE 80lpm MAX FLW RATE Auto TYPE IESEL Piusi Standard Auto Nozzle For non-resale diesel refuelling of vehicles Automatically shuts off when vehicle tank is full 3 position stay open latch ifferent flow versions available ATEX version available for use in flammable environments IESEL R RAPSIL P PETRL Professional Auto Nozzle For non-resale diesel refuelling of vehicles Automatically shuts off when vehicle tank is full Version for use only with diesel and version compatible with biodiesel up to B100 2 position stay open latch (diesel only version) Supplied as standard with No 4 trigger guard Splash guards available upon request IESEL B1 B100 P PETRL K KERSENE ZVA Slimline 2 Auto Nozzle High quality, heavy duty model from well known ZVA brand, approved for refuelling in resale pumping applications Automatically shuts off when vehicle tank is full 2 position stay open latch K KERSENE Code escription Flow Rate (lpm) Max Pressure (bar) Spout (mm) Inlet Connection Fluids Piusi Auto F BSP Swivel A Piusi Auto F BSP Swivel A Piusi Auto F BSP Swivel A Piusi Auto Rapsoil F BSP Swivel AQ Piusi ATEX Auto F BSP Swivel AGC Code escription Flow Rate (lpm) Max Pressure (bar) Spout (mm) Inlet Connection Fluids PF5023 Professional Auto Nozzle F BSP Swivel A PF5024 Professional Auto Nozzle B F BSP Swivel AP See page 83 for nozzle holsters ACCESSRIES ATEX approved for use in flammable environments Supplied as standard with No 4 trigger guard Splash guards available upon request Code escription Flow Rate (lpm) Max Pressure (bar) Spout (mm) Inlet Connection Fluids PF5001 ZVA Slimline 2 - ¾ ¾ F BSP Swivel AGC PF5017 ZVA Slimline F BSP Swivel AGC 82

82 Fuel Nozzles \ Nozzles IESEL P PETRL ZVA 25/32 Auto Nozzles High flow nozzles approved for refuelling in resale pumping applications from well known ZVA brand Automatically shuts offs when vehicle tank is full 2 position stay open latch Supplied with black scuff guard Two versions available depending upon the flow rate and pressure requirements of the installation Supplied as standard with No 4 trigger guard Splash guards available upon request IESEL Piusi A280 Auto Nozzle For high flow refuelling of large vehicles & heavy duty plant and agricultural machinery Automatically shuts offs when vehicle tank is full Large hand opening to accommodate for gloves Highest flow rate model in the Piusi range with large bore spout 200lpm MAX FLW RATE Auto Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Inlet Fluids PF5002 ZVA 25 High Flow Nozzle F BSP Swivel AG PF5003 ZVA 32 High Flow Nozzle ½ M BSP Swivel AG ANY FLUI Piusi Nozzle Holsters Universal Nozzle Holster - Metal Metal, adjustable universal nozzle hanger esigned to fit the Piusi Self 2000, Self 3000 & Piusi Standard Auto nozzle, but accepts most nozzles Nozzle Support - Plastic Small, reversible circular nozzle support for resting spout inside esigned to fit the Piusi Self 2000, Self 3000 & Piusi Auto 60 one way, Auto 80 & 120 the other way TYPE 280lpm MAX FLW RATE Auto Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Inlet Fluids F13249 Piusi A280 High Flow Nozzle ½ F BSP Swivel A TYPE Most Piusi NZZLE TYPE Wall/Tank MUNTING Code escription Material Type Fluids F Piusi Universal Nozzle Holster - Metal Metal Adjustable holster N R Piusi Nozzle Support - Plastic Plastic Circular support N Holster Support 83

83 Nozzles / Fuel Nozzles What sets the Husky fuel nozzle range apart from other models? Each nozzle in the Husky range has a selection of enhanced features that ensure both safety and serviceability Loss motion latch pin working in conjunction with a spring loaded diaphragm, it greatly reduces nuisance click offs and splash back spillages Patented Flo-Stop device nozzle shuts off when spout is raised above the horizontal or falls from the fill tank to prevent spillages and loss of fuel Reinforced spout bushing spout tip and inner diameter remain unworn even after excessive use, which prevents nuisance click offs and splash back Sensing port behind spout positioned behind rather than the end of the spout, ensuring the sensor is not subject to wear that increases its sensitivity and causes nuisance click offs Patented Stream Shaper - reduces turbulence and velocity for a straighter fuel flow, ensuring less splash back spillage elrin tipped stem reduces lever pad wear and allows more positive lowflow shut off Torsion clip spring enhances lever durability and prevents breakages Three position hold open clip requires only one hand to open nozzle and then put hold open latch on. If nozzle hits ground, latch flicks off and shuts off flow even when put in lock position Increased pressure closing poppet when more pressure is applied e.g. someone stands on hose, the poppet shuts the nozzle off to prevent leakage rather than pushing fuel out of spout and onto forecourt Anti-air lock feature stops nozzle from having to be removed from the hose when priming the pump The UK fficial Husky istributor Full metal hand guard Increased pressure closing poppet Locking lever guard IESEL X 1GS VIII 1690 Loss motion latch pin o o o o Flo-stop device o o o Reinforced spout bushing o* o** o Behind of spout sensing port o o o o Stream Shaper o* o** elrin tipped stem o o o Torsion clip spring o o o Three position hold open clip o o o Full metal hand guard o o o o Increased pressure closing poppet o o o o Anti-air lock feature ual poppet Three position hold open clip ual poppet o o * Smaller spout version as standard, larger spout version optional with Stream Shaper spout assembly ** ptional with Stream Shaper spout assembly ual poppet for easier opening of the nozzle when high system pressure is present due to high flow Loss motion latch pin Flo-stop device Packing: ouble o-ring seal protected by Teflon elrin tipped stem Torsion clip spring o Stream Shaper FEATURE Sensing port behind spout Reinforced spout bushing Full metal hand guard for enhanced durability 84

84 Fuel Nozzles \ Nozzles IESEL Husky X-Mate Auto Nozzle For non-resale diesel refuelling of commercial vehicles & cars Automatically shuts off when vehicle tank is full Flo-stop device shuts off flow when spout is raised or falls out Smaller models for refuelling vehicles with difficult fill points Stream Shaper as standard on smaller models & can be fitted to larger models by purchasing the spout assembly ne piece metal casting for durability with mate (half) scuff guard Code escription Max Flow Rate (lpm) IESEL Husky 1-GS Auto Nozzle For refuelling larger vehicles and agricultural machinery Automatically shuts off when vehicle tank is full Flo-stop device shuts off flow when spout is raised or falls out Anti-air lock feature for priming of pump without removing nozzle Integrated hook for hanging nozzle without a holster Aluminium body for heavier duty applications with full scuff guard Stream Shaper can be fitted with the optional spout assembly IESEL Husky VIII Auto Nozzle For high flow refuelling of large agricultural & plant machinery Automatically shuts off when vehicle tank is full Flo-stop device shuts off flow when spout is raised or falls out Free-floating turbulent flow reducer for ensuring a streamline flow c/w waffle guard to protect against splash backs Max Pressure (bar) Aluminium body for heavier duty applications with full scuff guard Spout (mm) High flow swivel available for maintaining 250lpm if flow rate is vital Inlet 60lpm MAX FLW RATE Auto TYPE Stream Shaper 100lpm MAX FLW RATE Auto TYPE 250lpm MAX FLW RATE Auto TYPE See page 84 for enhanced features INFRMATIN Version c/w 1" F BSP Swivel HU-E Husky X-Mate Nozzle Small UL ¾ F BSP o HU-E SW A HU-E Husky X-Mate Nozzle Large L ¾ F BSP HU-E SW A HU-8862 Stream Shaper Spout Assembly 23.8 o A Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Inlet Stream Shaper See page 84 for enhanced features INFRMATIN Version c/w 1" F BSP Swivel HU Husky 1GS Nozzle F BSP HU SW A HU-8862 Stream Shaper Spout Assembly 23.8 o A See page 84 for enhanced features INFRMATIN Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Inlet Fluids HU Husky VIII High Flow Nozzle F BSP A HU SW Husky VIII High Flow Nozzle Swivel F BSP Swivel A HU-6949 Husky High Flow Swivel F BSP Swivel A Fluids Fluids 85

85 Nozzles / Fuel Nozzles See page 84 for enhanced features INFRMATIN 375lpm MAX FLW RATE Auto TYPE Husky 1690 Auto Nozzle Heavy duty nozzle for high flow, bulk fuel transfer applications such as rail, tanker or filling storage tanks Automatically shuts off when vehicle tank is full 30% lighter than similar models for easy handling Right angle design to allow the nozzle to fit close to walls Large hand opening to accommodate for gloves Check valve is in the nozzle body rather than spout for easy serviceability Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Inlet Fluids HU Husky 1690 Tank Nozzle ½ F BSP A HU SW Husky 1690 Tank Nozzle Swivel ½ F BSP Swivel A 190lpm MAX FLW RATE Auto 380lpm MAX FLW RATE IESEL J JET FUEL Husky sprey Aviation Nozzle Specifically for over-the-wing refuelling of aircraft Automatically shuts off when aircraft tank is full Easy to service 100 mesh stainless steel fuel filter screen ne piece aluminium body for enhanced durability Full red scuff guard to identify use with aviation fuel & waffle guard Spout cap & chain & ground cable with clip for earthing the nozzle to the aircraft Pressure sensing valve to only release fuel when pump is operating Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Inlet Fluids HU Husky sprey S Aviation Nozzle F BSP S TYPE Manual TYPE J JET FUEL Husky Eagle Aviation Nozzle Specifically for over-the-wing refuelling of aircraft Heavy duty, high flow manual nozzle with handle guard & side protection c/w both duck bill jet & round aviation swivelling fuel spouts & spout caps Easy to service 100 mesh stainless steel fuel filter screen Easy operation, fingertip sensitivity & adjustable closing speed Meets EI 1540 and NPFA 407 standards Suitable for AVGAS, AVJET A1, Aspen 2, Aspen 4 Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Inlet Fluids HU Husky Eagle Aviation Nozzle ½ F BSP Swivel S 86

86 Lube il Nozzles \ Nozzles IL Piusi K500 Pre-set Nozzle Pre-set oil dispensing nozzle c/w automatic spout that shuts off when the selected quantity has been dispensed Trigger protection to prevent accidental operation outside of the pre-set transaction +/-0.5% accuracy & changeable unit of measure Pre-select range litres Viscosity up to 2000cSt IL Piusi Easyoil Nozzle ispensing nozzle designed for oil filling operations in a garage, workshop or industrial environment Swivel inlet contains wire mesh filter Trigger lock to prevent accidental operation Balanced valve to reduce pressure on the trigger ther spout configurations available upon request Colour coded hand grips & swivel protectors available on request 30lpm MAX FLW RATE Rigid SPUT TYPE Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout Type Inlet Connection Batteries Fluids 68700B Piusi K500 Pre-set Nozzle Rigid ½ F BSP Swivel 4 x AA 1.5v F 30lpm MAX FLW RATE Rigid/Flexi SPUT TYPE Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout Type Inlet Connection Fluids Piusi Easyoil Rigid Spout Rigid ½ F BSP Swivel F Piusi Easyoil Flexi Spout Flexi ½ F BSP Swivel F 976W10 Piusi Easyoil Windscreen Plastic ½ F BSP Swivel I IL WS WINSCREEN WS WINSCREEN Piusi K400 Nozzle Easyoil nozzle with integrated K400 digital meter (+/-0.5% accuracy) Swivel inlet contains wire mesh filter Trigger lock to prevent accidental operation Automatic non-drip valve on spout versions ther spout configurations available upon request Colour coded hand grips & swivel protectors available on request 30lpm MAX FLW RATE Rigid/Flexi SPUT TYPE Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout Type Inlet Connection Fluids F Piusi K400 Nozzle Rigid Spout Rigid ½ F BSP Swivel F Up to 2000cSt F Piusi K400 Nozzle Flexi Spout Flexi ½ F BSP Swivel F Up to 2000cSt F Piusi K400 Nozzle No Spout No ½ F BSP Swivel F Up to 2000cSt 976W00 Piusi K400 Nozzle Windscreen Plastic ½ F BSP Swivel 87

87 Nozzles / Lube il Nozzles 30lpm MAX FLW RATE Rigid/Flexi SPUT TYPE Piusi K40 Nozzle Easyoil nozzle with integrated K40 mechanical meter (+/-1% accuracy) Swivel inlet contains wire mesh filter Trigger lock to prevent accidental operation Viscosity up to 500cSt ther spout configurations available upon request Colour coded hand grips & swivel protectors available on request Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout Type Inlet Connection Fluids F Piusi K40 Nozzle Rigid Spout Rigid ½ F BSP Swivel F F Piusi K40 Nozzle Flexi Spout Flexi ½ F BSP Swivel F F Piusi K40 Nozzle No Spout No ½ F BSP Swivel F 90lpm MAX FLW RATE Rigid/Flexi SPUT TYPE IL IL Piusi Pistol-ne Nozzle High capacity nozzle designed for high flow, heavy duty oil filling applications even at high pressures Swivel inlet contains wire mesh filter Balanced valve to reduce pressure on the trigger Versions with rigid or flexible spout available Non-drip semi-automatic valve on spout versions Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout Type Inlet Connection Fluids F Piusi Pistol-ne Rigid Spout Rigid ¾ F BSP Swivel F F Piusi Pistol-ne Flexi Spout Flexi ¾ F BSP Swivel F F Piusi Pistol-ne No Spout None ¾ F BSP Swivel F 60lpm MAX FLW RATE Rigid/Flexi SPUT TYPE IL Piusi Next/2 Nozzle High capacity nozzle designed for high flow, heavy duty oil filling applications even at high pressures Integrated Next/2 digital meter with +/- 0.5% accuracy Swivel inlet contains wire mesh filter Balanced valve to reduce pressure on the trigger Versions with rigid or flexible spout available Non-drip semi-automatic valve on spout versions Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout Type Inlet Connection Fluids F Piusi Next/2 Rigid Spout Rigid ¾ F BSP Swivel F F Piusi Next/2 Flexi Spout Flexi ¾ F BSP Swivel F F Piusi Next/2 No Spout None ¾ F BSP Swivel F 88

88 Grease Nozzles \ Nozzles GR GREASE Piusi Greaster Grease dispensing nozzle with integrated oval gear meter Lever lock to avoid accidental opening of valve +/- 3% accuracy LC display showing resettable batch total (gr) for individual operations and a cumulative consumption total (kg) Two 1.5v AA battery compartment integrated in the aluminium constructed nozzle handle GR GREASE Manual Grease Control Nozzle For the dispensing point of an air operated grease pump installation Spring type pistol trigger c/w both a rigid spout & flexible outlet hose with 4 jaw connector ¼ F BSP straight swivel inlet connection Z swivel available as an inlet accessory 2.5kg/min MAX FLW RATE Rigid SPUT TYPE Code escription Flow Rate (kg/min) Max Pressure (bar) Spout Type Inlet Connection utlet Connection Fluids Piusi Greaster Rigid ¼ F BSP Z Swivel M 10 x 1 K GR GREASE Grease Gun Holder Simple snap action clamp for the secure storing of grease guns esigned for grease guns with a barrel diameter of 57mm, which accept a 400cc cartridge Suitable for mounting onto almost any surface Constructed from heavy gauge steel sheet with zinc plated finish Manual PWER Rigid/Flexi SPUT TYPE See page 24 for grease pumps RELATE PRUCTS Code escription Max Pressure (bar) Inlet Connection Spout Fluids CTS1031 Grease Control Nozzle 4 Jaw Coupler 600 ¼ F BSP Swivel Rigid & Flexi K GV9002 Z Swivel K 400cc Guns FR USE WITH See page 90 for grease guns RELATE PRUCTS Code escription For Use With Material Fluids CTS1030 Grease Gun Holder 400cc Cartridge Guns Heavy Gauge Steel K Grease Control Nozzle Z Swivel 89

89 Nozzles / Grease Nozzles Manual PWER Rigid/Flexi SPUT TYPE GR GREASE Professional Grease Gun Manual grease gun for simple and cost effective grease dispensing Accepts 400cc cartridges or 500cc bulk fill c/w both rigid and flexible spouts Side lever & pistol grip versions available depending upon customer preference Code escription Cartridges Spout Type Jaw Connection Fluids GRGS400 Professional Grease Gun Side Lever 400cc & 500cc Bulk Rigid & Flexi 4 K GRGP400 Professional Grease Gun Pistol Type 400cc & 500cc Bulk Rigid & Flexi 4 K Air PWER Rigid/Flexi SPUT TYPE GR GREASE Air perated Grease Gun esigned for frequent & larger volume grease dispensing as they can dispense multiple cartridges on a single charge Accepts 400cc cartridges or 500cc bulk fill c/w both rigid and flexible spouts Maximum air inlet of 3 bar Popular within workshop and garage environments where there is an existing air line Comes as standard with a manual lever handle for where air is not available Code escription Cartridges Max Pressure (bar) Spout Type Jaw Connection Fluids GRGA400 Air perated Grease Gun 400cc & 500cc Bulk 340 Rigid & Flexi 2 & 4 K 12v PWER 400mm GREASE HSE GR GREASE 12v Powered Grease Gun esigned for frequent & larger volume grease dispensing as they can dispense multiple cartridges on a single charge Accepts 400cc cartridges or 500cc bulk fill c/w 400mm grease hose Supplied in carry case with 110/230v charger & 2 batteries (holds a 1 hour battery charge) Heavy duty option available for higher pressure installations c/w shoulder strap Ideal for agriculture & plant equipment Code escription Cartridges Max Pressure (bar) Grease Hose Jaw Connection Fluids A Grease Gun 400cc or 500cc Bulk mm 4 K A2000/H 12v Heavy uty Grease Gun 400cc or 500cc Bulk mm 4 K 90

90 AdBlue Nozzles \ Nozzles AB ABLUE W WATER Piusi Suzzara Blue Manual Nozzle Cost effective solution for dispensing AdBlue Suitable for both pump & gravity fed installations Polypropylene body with a stainless steel spout Integral hook for hanging nozzle without a holster Removable 3/4" hose tail inlet leaving 1" M BSP if required 80lpm MAX FLW RATE Manual Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Seal Material Inlet Connection Fluids F Suzzara Blue Manual Nozzle Viton ¾ Hose Barb/1" M BSP JI AB ABLUE W WATER Piusi Stainless Steel Auto Nozzle esigned for the dispensing of AdBlue within pump installations Automatically shuts off when vehicle tank is full Stainless steel body & spout with plastic guard for comfort 3 position stay open latch 3/4" swivel hose tail for easy hose connection by means of a stainless steel jubilee clip TYPE 60lpm MAX FLW RATE Auto Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Seal Material Inlet Connection Fluids F Piusi Stainless Steel Auto Nozzle Viton ¾ Hose Barb Swivel JI AB ABLUE W WATER ZVA AdBlue Auto Nozzle esigned for the dispensing of AdBlue within pump installations Automatically shuts off when vehicle tank is full High quality, heavy duty model from well known ZVA brand nly dispenses when in contact with the Elafix 40 magnetic adaptor fitted in the vehicle tank to prevent miss-filling into a diesel tank and vice versa TYPE 40lpm MAX FLW RATE Auto Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Seal Material Inlet Connection Fluids F ZVA AdBlue Nozzle Viton ¾ Hose Barb Swivel JI F Elafix 40 Magnetic Adaptor JI TYPE 91

91 Nozzles / AdBlue Nozzles Code escription Max Flow Rate (lpm) Max Pressure (bar) Spout (mm) Seal Material Inlet Connection Meter Fluids F F FEATURE SB325 Nozzle Piusi SB325 Breakaway Nozzle Piusi SB325 Breakaway Nozzle Meter Safety & serviceability guaranteed with the SB325 breakaway spout nozzle SB325 Nozzle Meter 35lpm MAX FLW RATE Auto TYPE Breakaway Spout System If the driver drives off leaving the nozzle in the vehicle fill point, the spout will detach, preventing the pump from being pulled away with it. ** SB325 is compatible with all ZVA Slimline 2 trigger guards Viton Viton Piusi SB325 AdBlue Nozzle with Breakaway Spout The Piusi SB325 is designed for the dispensing of AdBlue and automatically shuts off when the vehicle tank gets full. Available is a standard version as well as a model with an integrated K24 digital flow meter, for easily monitoring the amount dispensed. The SB325 nozzle benefits from a breakaway spout mechanism. In the event that a vehicle accidently drives away with the nozzle still in the tank, the spout is designed to break away from the nozzle body. This allows for quick nozzle repair by merely fitting a replacement spout. ptional Accessories... R R F F F ¾ Hose Barb/ 1" M BSP ¾ Hose Barb/ 1 " M BSP o J J AB ABLUE Replacement stainless steel spout available to repair the nozzle after the breakaway spout mechanism has been in use Magnetic miss-filling spout prevents the miss-filling of AdBlue into a diesel tank by only releasing fluid into a vehicle that has a vehicle tank magnetic adaptor fitted Elafix 40 vehicle tank magnetic adaptor for fitting into the AdBlue fill point of a vehicle and using with the magnetic miss-filling spout as detailed above Nozzle magnetic adaptor allows a magnetic spout to dispense when not in contact with a tank magnetic adaptor e.g. when dispensing into a smaller container or if you have some vehicles with a tank adaptor & some without Nozzle magnetic adaptor kit is the above adaptor plus the magnetic missfilling spout as a complete kit 92

92 Contents \ Tank Alarms & verfill Prevention TANK ALARMS & VERFILL PREVENTIN TANK ALARMS VERFILL PREVENTIN ALARMS PV

93 Tank Alarms & verfill Prevention / Tank Alarms FEATURE Single Probe ouble Probe Select the probes you require with the versatile multi-zone tank alarm Selecting your probes... To make the alarm as versatile as possible, we offer the box alone as standard, giving you the option to select the probes you require. This means only one alarm box needs to be stocked to cover all requirements. Single probe For high level, low level or bund warning ouble probe - For two level alerts; high/low, high/high or low/low ouble & single probe - For all three functions; high, low & bund Probes for other fluids... il rum High viscosity Water & Chemical Single/ouble PRBES See page 95 for alarm boxes RELATE PRUCTS IESEL IL AB ABLUE C CHEMICAL Multi-Zone Tank Alarm Range & Probes The multi-compartment fuel tank alarms are industry renowned models designed to accurately detect and alert the user of a combination, or all, of the following tank states: High fuel level to help avoid further filling and an overspill from occuring Low fuel level to indicate that a fuel delivery needs to be ordered Bund alert to warn that fluid is present which may indicate a leak or the ingress of rain water Code escription Alerts Cable Connection Fluids SWS1035 SWS1035/2 SWS1036 SWS1037 Single Alarm Probe ouble Alarm Probe Flat Plate & Grommet for Plastic Tanks Single Flat Plate & Grommet for Plastic Tanks ouble High/Low /Bund High & Low 5m PVC 5m PVC 1 ½ F BSP Brass Cap 1 ½ F BSP Brass Cap AF AF AF AF SWS1009 Alarm Cable Per Metre 1m PVC AF High viscosity probe - For heavy fuel oils & fluids that crystallise e.g AdBlue Code Alerts Temp Cable Connection Fluids SWS1038 High/Low 0 c/+60 c 5m PVC 1 ½ F BSP Cap FJ il drum probe - To alert of a high fluid level in waste oil storage systems Code Alerts Temp Cable Connection Fluids SWS1039 High -20 c/+80 c 5m PVC ¾ M BSPT Steel rum F Water & chemical probe - For level alerts on water & chemical tanks Code Alerts Temp Cable Connection Fluids SWS1040 High/Low -20 c/+80 c 5m PVC 1 ½ F BSP Polyethylene Cap IL W WATER 94

94 Tank Alarms \ Tank Alarms & verfill Prevention ANY FLUI Mains Multi-Zone Tank Alarm Mains multi-channel tank alarm for high, low and/or bund 90db sounder & flashing orange strobe to warn of tank state Zone in question lights up on the screen to indicate the issue Test & alarm mute functions Automatically reversed float logic for low zones Weatherproof IP55 enclosure Standard box with multiple input voltages 110v/120v/, 12v/24v C ption with relays available to connect to external equipment e.g. other alarms or building management systems Version with relays can also be used to control the pump operation on a day tank e.g. to turn it on when low level is reached Please note: Probes are purchased seperately, please select the ones you require from the opposite page's table ANY FLUI Battery Multi-Zone Tank Alarm Battery multi-channel tank alarm for high, low and/or bund esigned for isolated or portable installations where mains power is unavailable 90db sounder and flashing red LE to warn of tank state Zone in question lights up on the screen to indicate the issue Test & alarm mute functions Low battery warning Automatically reversed float logic for low zones Weatherproof IP55 enclosure ption with relays available to connect to external equipment Please note: Probes are purchased seperately, please select the ones you require from the opposite page's table Multi ZNES Electric PWER See page 94 for probes RELATE PRUCTS Code escription V Relays Fluids SWS2000 Mains Multi-Compartment Alarm Box 110/230/12v/24v N SWS2001 Mains Multi-Compartment Alarm Box c/w Relays 110/230/12v/24v 3 N Multi ZNES Battery PWER See page 94 for probes RELATE PRUCTS Code escription Batteries Relays Fluids SWS1000 Battery Multi-Compartment Alarm Box 6 x AA N SWS1001 Battery Multi-Compartment Alarm Box c/w Relays 6 x AA 3 N 95

95 Tank Alarms & verfill Prevention / Tank Alarms Single ZNES Mains/ Battery PWER Single Channel Tank Alarm Tank alarm c/w single probe to warn of a choice of either high, low or bund Simple & cost effective solution if only one alert is required 90db sounder & red LE text display to warn of tank state Test & alarm mute functions Automatically reversed float logic for low zones Weatherproof IP55 enclosure with 4 external mounting lugs Mains, battery and mains with battery back-up versions Low battery warning (battery version only) Mains version c/w relay for connecting to external equipment e.g. other alarms or building management systems Suitable for use with diesel and light oils Code escription Power Probe Relay Fluids SWS2002 Mains Single Channel Tank Alarm 230v o o AF SWS1011 Battery Single Channel Tank Alarm 1 x PP3 Battery o AF SWS2003 Mains Single Channel Tank Alarm c/w Battery Back-up 230v o o AF See page 95 for multi-zone alarms RELATE PRUCTS Single ZNES Battery PWER See page 95 for multi-zone alarms RELATE PRUCTS IESEL IESEL IL IL Economy Bund Alarm Battery tank alarm c/w single probe to alert of presence of fluid in the bund Simple & cost effective solution if only bund alert is required Used to indicate either the inner tank leaking into the bund or excess rain water Flashing red LE & 90db alarm will sound to alert the user to a problem Test & alarm mute functions Weatherproof IP55 enclosure with 4 external mounting lugs Battery will last in excess of 72 hours in full alarm mode and approx 2 years when in standby Suitable for use with diesel and light oils Customised branding available - please ask Code escription Battery Probe Fluids SWS1019 Bund nly Alarm 1 x PP3 o AF 96

96 verfill Prevention \ Tank Alarms & verfill Prevention IESEL K KERSENE AB ABLUE Lafon Cleanfill verfill Prevention Automatically operating overfill prevention valve Valve closes when the tank is full, to prevent further fluid from being dispensed and spillages from occurring evice can easily be retrofitted to both gravity-fed & pumping installations Less than one minute re-opening time EN13616/KIWA BRL-K363 accredited Alloy version for fuel and stainless steel version for AdBlue tanks available lpm FLW RATE RANGE 2" M BSP INLET Cleanfill AdBlue Version Code escription Flow Rate Range (lpm) Pressure Range (bar) Inlet Connection Working Temp Material Fluids N50 2 Cleanfill PV M BSP -25 c/+50 c Alloy AC N51 2 Cleanfill PV AdBlue M BSP -10 c/+35 c Stainless Steel JI IESEL K KERSENE SpillStop verfill Prevention Cost effective, automatically operating overfill prevention valve Valve closes when the tank is full, to prevent further fluid from being dispensed and spillages from occurring evice can easily be retrofitted to both gravity-fed & pumping installations Less than one minute re-opening time BS EN13616 & FTEC approved Version for installation onto steel tanks and version for use with plastic tanks lpm FLW RATE RANGE 2" M BSP INLET Spillstop Plastic Tank Code escription Flow Rate Range (lpm) Pressure Range (bar) Inlet Connection Working Temp Fluids N50/2 2 SpillStop PV M BSP -20 c/+50 c AC N50/2P 2 SpillStop PV Plastic Tanks M BSP -20 c/+50 c AC 97

97 Tank Alarms & verfill Prevention / verfill Prevention lpm FLW RATE RANGE 3" F BSP INLET IESEL K KERSENE P PETRL C CHEMICAL Solo Limiter verfill Prevention verfill prevention valve for high capacity above & below ground storage tanks fed by gravity or pump Valve closes when the tank is full, to prevent further fluid from being dispensed and spillages from occurring Anti-vortex to prevent valve closing prematurely Less than one minute re-opening time EN13616/KIWA BRL-K363 accredited ATEX approved for Zone 0 Versions for fuel and chemicals available Please note: Installation is required at the manufacturing stage Code escription Flow Rate Range (lpm) Pressure Range (bar) Inlet Connection Working Temp Fluids N30 3 Solo Limiter PV F BSP -25 c/+60 c ACG N80 3 Solo Limiter PV Chemicals F BSP -25 c/+60 c L Multi ZNES Mains PWER See page 95 for multi-zone alarms RELATE PRUCTS IESEL B1 B100 IL GSM Text Alerter esigned for the remote monitoring of low or high level should the user wish to know when the tank needs emptying/filling Unit allows 4 trigger inputs to be set, which send a text upon activation Customised 30 character SMS to up to 8 mobile phones Ideal for remote monitoring of tank level IP55 rated enclosure Code escription V Level Probes Fluids CTS6000 GSM Text Alerter c/w ouble Probe ouble APF CTS6001 GSM Text Alerter Box nly APF Version without probes for connecting to another device such as the output relays on a fuel tank alarm Please note: A mobile phone & GSM SIM card are required to program and use the unit 98

98 Contents \ Tank & rum Gauges TANK & RUM GAUGES MECHANICAL ELECTRNIC SIGHT LEVEL 106 MECHANICAL ELECTRNIC SIGHT LEVEL

99 Tank & rum Gauges / Mechanical Gauges Fraction REAING Specific TANK HEIGHT 0-100% REAING Adjustable TANK HEIGHT MT Profil Float Gauge Simple & economical float operated clock gauge for the quick & clear identification of approximate tank contents Small mechanical display showing Empty, ¼, ½, ¾, Full esigned for use on specific tank heights 8 0 version is adjustable to the individual tank height & has a a reversible display showing 150cm max on one side & 250cm max on the other Supplied as 1 ½ M BSP for easy top mounting onto the tank Popular choice for heating oil tanks Code escription Reading Type Tank Height (ft/mm) Gauge Fitting Fluids AB3001 MT Profil Float Gauge 1 6 Empty, ¼, ½, ¾, Full 1 6/457 1 ½ M BSP ACP AB3002 MT Profil Float Gauge 2 0 Empty, ¼, ½, ¾, Full 2 0/610 1 ½ M BSP ACP AB3004 MT Profil Float Gauge 2 6 Empty, ¼, ½, ¾, Full 2 6/762 1 ½ M BSP ACP AB3003 MT Profil Float Gauge 3 0 Empty, ¼, ½, ¾, Full 3 0/904 1 ½ M BSP ACP AB3304 MT Profil Float Gauge 4 0 Empty, ¼, ½, ¾, Full 4 0/ ½ M BSP ACP AB3305 MT Profil Float Gauge 5 0 Empty, ¼, ½, ¾, Full 5 0/ ½ M BSP ACP AB3309 MT Profil Float Gauge 6 0 Empty, ¼, ½, ¾, Full 6 0/ ½ M BSP ACP AB3308 MT Profil Float Gauge 8 0 Cm isplay 8 0/ ½ M BSP ACP IESEL K KERSENE MTF 2000 Float Gauge Cost effective, universal float operated clock gauge for the quick & clear identification of tank contents Small mechanical display showing percentage of contents remaining in the tank Fully adjustable between tank heights of 900mm-2000mm so only one model needs to be stocked Gauge can be directly mounted onto 1 ½ & 2 F BSP threads for flexibility of installation Brass and nickel silver movement Long service life B1 B100 Popular choice for heating oil tanks Code escription Reading Type Tank Height (ft/mm) Gauge Fitting Fluids AB3320 MTF 2000 Float Gauge 0-100% 3 0/904 to 6 7/ ½ & 2 M BSP ACP IESEL K KERSENE B1 B

100 Mechanical Gauges \ Tank & rum Gauges IESEL Unitel Hydrostatic Gauge Pneumatic tank gauge with spring loaded plunger to pull & release to show current tank contents Mechanical display showing tank contents as a percentage (standard version) or in litres (calibrated version) Fully adjustable between tank heights of 900mm-3000mm Accuracy of +/-3% at full scale ual scale for use on horizontal & rectangular tanks Adjustable second needle for setting the level parameter for when you need to reorder fuel Gauge face dimensions 145mm x 135mm Please request or download from the website the tank questionnaire for calibrated gauges. IESEL K KERSENE K KERSENE B1 B100 B1 B100 AB ABLUE AB ABLUE Unitop Hydrostatic Gauge Pneumatic tank gauge with spring loaded plunger to pull & release to show current tank contents Mechanical display showing tank contents as a percentage (standard version) or in litres (calibrated version) Fully adjustable between tank heights of 900mm-3000mm (standard version) and 700mm-4000mm (calibrated version) Accuracy of +/-2% at full scale W WATER Code escription Reading Type ual scale for use on horizontal & rectangular tanks Adjustable second needle for setting the level parameter for when you need to reorder fuel Gauge face dimensions 155mm x 165mm Tank Height (mm) Capillary Please request or download from the website the tank questionnaire for calibrated gauges. Balance Chamber Tank Fitting Balance Chamber Weight Working Temp AB9000 Unitel Gauge 0-100% m PVC ½ M BSP & 1 M BSP Stainless Steel -5 C/+55 C ACPJI AB9000C Unitel Gauge - Calibrated Litres m PVC ½ M BSP & 1 M BSP Stainless Steel -5 C/+55 C ACPJI AB9004 Unitel Condensation Trap ACPJI W WATER Code escription Reading Type Tank Height (mm) Capillary Balance Chamber Tank Fitting % or Litres REAING +/-3% ACCURACY % or Litres REAING +/-2% ACCURACY Balance Chamber Weight Working Temp AB8000 Unitop Gauge 0-100% m PVC ½ M BSP & 1 M BSP Stainless Steel -5 C/+55 C ACPJI AB3318 Unitop Gauge - Calibrated Litres m PVC ½ M BSP & 1 M BSP Stainless Steel -5 C/+55 C ACPJI AB9004 Unitel Condensation Trap ACPJI Fluids Fluids 101

101 Tank & rum Gauges / Mechanical Gauges Code escription Reading Type % or Litres REAING Multiple TANK HEIGHT Tank Height (mm) Capillary IESEL Normond C/E Hydrostatic Gauges Pneumatic tank gauge with pump up plunger to show current tank contents Large mechanical display showing tank contents as a percentage (E Series) or is calibrated to show volume (C Series) Suitable for tanks up to 3000mm (C Series) or 9000mm (E Series) To work out which E Series gauge you need, take the tank height in mm & select the gauge your tank falls into the middle of Popular choice for commercial sites thanks to their reliability & robust nature C/E Series gauge face dimensions 165mm x 165mm Please request or download from the website the tank questionnaire for the calibrated C Series IESEL K KERSENE Balance Chamber Tank Fitting K KERSENE C CHEMICAL Balance Chamber Weight Normond G Hydrostatic Gauge Highly accurate pneumatic tank gauge with pump up plunger to show current tank contents Large mechanical display calibrated to show volume Suitable for most liquids and large tanks up to 10000mm high that may have difficult access Usually selected over the C Series when the tank is too high or the measured fluid is not diesel Suitable for hazardous environments Max Working Temp AB6000 Normond Gauge C Series Litres m PVC ½ M BSP Brass +38 C AC AB6001 Normond Gauge E Series Low 0-100% m PVC ½ M BSP Brass +38 C AC AB6001M Normond Gauge E Series Medium 0-100% m PVC ½ M BSP Brass +38 C AC AB6001H Normond Gauge E Series High 0-100% m PVC 1 M BSP & 1 ½ M BSP Brass +38 C AC AB6001S Extra Capillary Tubing Per Metre AC Litres REAING Upto 10m TANK HEIGHT Code escription Reading Type Tank Height (mm) Capillary Length (m) Please note: No balance chamber or capillary is included. It will be specified upon receipt of questionnaire Gauge face dimensions 165mm x 165mm Fluids Please request or download from the website the tank questionnaire for the calibrated G Series Balance Chamber Tank Fitting Balance Chamber Weight Max Working Temp AB6002 Normond Gauge G Series Litres C ACL Fluids 102

102 Electronic Gauges \ Tank & rum Gauges ANY FLUI Apollo il Tank Gauge Easy to retrofit, ultrasonic tank contents gauge for heating oil tanks Transmitter fits on top of the tank & the receiver plugs into a socket inside the property to conveniently display the tank level igital display bar graph reading on receiver 10% tank height per bar Apollo Visual has a transmitter bar graph display for monitoring the local tank reading Flashing LE to show when tank is empty Transmitter to receiver range is 200m depending on obstacles Receiver: v, 50/60Hz Transmitter: 3v lithium battery (approx. 10 years) Code escription Reading Type Tank Height (mm) Apollo Smart il Tank Gauge Easy to retrofit, ultrasonic tank contents gauge for heating oil tanks Transmitter fits on top of the tank & the desktop receiver plugs into a wall socket via a transformer to conveniently display the tank level igital display litre & bar graph reading on receiver 10% tank height per bar Transmitter has a local bar graph display Audible low level alarm & anti-theft alarm which sounds if the fuel level drops suddenly Monitors fuel consumption levels in litres & cost by day, week, month or year & the number of days you have until tank is empty Provides room temperature reading & C2 emission data Transmitter to receiver range is 150m depending on obstacles Receiver: v, 50/60Hz Transmitter: 3v lithium battery (approx. 10 years) Local isplay Bar Graph REAING Two Part TYPE Remote isplay Bar/Litres REAING Two Part TYPE Tank Fitting Working Temp Fluids APULM Apollo il Gauge Bar Graph o 32mm -10 C/+60 C N APULMVIS Apollo Visual il Gauge Bar Graph o o 32mm -10 C/+60 C N APULM02 Apollo Steel Tank Adaptor 1 ½ & 2 M BSP N APULM03 Apollo Visual Steel Tank Adaptor 1 ½ & 2 M BSP N ANY FLUI Apollo Visual Code escription Reading Type Tank Height Local isplay Remote isplay Tank Fitting Working Temp Fluids (mm) APULMSMART Apollo Smart il Gauge Bar Graph & Litres o o 32mm -10 C/+60 C N 103

103 Tank & rum Gauges / Electronic Gauges Watchman Watchman isplay Bar Graph REAING Two Part TYPE Watchman il Tank Gauge Easy to retrofit, ultrasonic tank contents gauge designed for plastic & steel domestic heating oil tanks Transmitter fits on top of the tank & the receiver plugs into a socket inside the property to conveniently display the tank level igital bar graph reading on receiver 10% tank height per bar for simple visual indication Pump symbol appears to prompt a fuel delivery when tank level falls below 10% Flashing red LE to show when tank is empty Transmitter to receiver range is 200m depending on obstacles Receiver: v, 50/60Hz; Transmitter: 3v lithium battery Battery life approx. 3 years Code escription Reading Type Tank Height (mm) Remote isplay Tank Fitting Working Temp Fluids WATCH01 Watchman Sonic il Gauge Bar Graph o 32mm & 2 M BSP -10 C/+60 C N cio isplay ptions %/Litres/mm REAING +/-1% ACCURACY See page 53 for cio 2.0 RELATE PRUCTS Please note: Tank opening needs to be minimum 30mm diameter for balance chamber weight Code escription Reading Type Tank Height (mm) Capillary Length (m) ANY FLUI IESEL W WATER IL Piusi cio Fuel Tank Gauge Continuous reading, hydrostatic tank contents gauge for commercial tanks igital display reading in percentage, level (mm) or volume (Litres) Accuracy of +/-1% at full scale Low & high level status alerts can be set up, with flashing LE screen upon activation c/w two configurable relays for connecting to other equipment e.g. a low/high level alarm Supplied with 10m of capillary, but can work up to 50m Can be calibrated on site Versions for diesel and AdBlue, and optional oil kit 4-20ma version for use with building management systems Tank shapes - vertical cylindrical, horizontal cylindrical & rectangular Balance Chamber Tank Fitting AB ABLUE Balance Chamber Weight Working Temp F cio 230v 0-100% mm/inches litres/gals ½ M BSP Brass -20 C/+50 C AIF* F B cio 110v 0-100% mm/inches litres/gals ½ M BSP Brass -20 C/+50 C AIF* F cio 230v AdBlue 0-100% mm/inches litres/gals ½ M BSP Stainless Steel C/+50 C J F cio 230v 4-20ma 0-100% mm/inches litres/gals ½ M BSP Brass -20 C/+50 C AIF* F cio il Kit 3 F cSt *nly suitable for oil if il Kit is purchased Fluids 104

104 Electronic Gauges \ Tank & rum Gauges ANY FLUI cio esk Software cio esk software connects the cio to a PC to allow the viewing of the tank level status direct from the computer Provides visual indication of tank level as well as in percentage, level (mm) or volume (Litres) Current & historic tank level data is displayed graphically which can be used to identify any unusual results Can be set up to update at a specified time interval or variation in level or volume Connection is via USB interface & can transmit data via 2 core screened cable to a PC 900m away (multi-core cable required for multi-tank versions) Can connect up to 12 different tanks cio gauges to the same PC (depending upon software version) ANY FLUI cio GSM cio GSM connects to the cio gauge & sends the current tank level via SMS for remote monitoring Sends an alert via SMS when the tank level enters or exits the predetermined low/ high level state Can be set up to send a tank level reading in mm at predetermined timed intervals Tank level readings can be sent on demand by texting the SIM card set up on the GSM unit GSM transmitter can control up to 8 different cios via a 9 core screen data cable Max length 9 core screen cable 900m between cio & GSM/ Expansion box and 5m between GSM & Expansion box System requires a GSM SIM card with a system supporting up to 10 mobile phone numbers in the built-in phonebook nly compatible with 3G cio USE WITH Up to 12 TANK NUMBER Code escription Number of Tanks Software C PC Interface F00755S10 cio esk Single Tank 1 o 1 x Single Port USB Hub F00755S00 cio esk 4 Multi Tank 4 o 1 x Quad Port USB Hub F00755S20 cio esk 8 Multi Tank 8 o 2 x Quad Port USB Hub F00755S30 cio esk 12 Multi Tank 12 o 3 x Quad Port USB Hub cio USE WITH Up to 8 TANK NUMBER cio Software Screenshot cio GSM Required Models Code escription Number of Tanks V Colour Code F00755G30 cio GSM Quad Band White F00755G20 cio GSM Tank Expander for 2-4 Tanks 2-4 Grey F00755G40 cio GSM Tank Expander for 5-8 Tanks 5-8 Yellow 105

105 Tank & rum Gauges / Sight Gauges Gem Gauge Filter Service Kit Visual REAING Pull TYPE IESEL IL Gem Sight Level Gauge A cost effective pull to read gauge to give an instant measurement of tank contents for bottom outlet steel & plastic tanks Integrated paper filter with alloy removable bowl for easy cleaning Isolation valve so the gauge can be serviced without draining the tank Multi-directional outlet so fuel can be taken from right or left or can feed two boilers Supplied with gauge level marking kit & litre calibration labels Quality corrosion resistant zinc plated brass body Code escription Height (ft/mm) Inlet Primary utlet Secondary utlet Filter Tube Support Fluids GEM1000A Gem 4ft 6in Sight Gauge 4 6/1371 ½ M BSP 3/8 F BSP x 10mm Compression 3/8 F BSP 40µ Plastic CAF GEM1002A Gem 6ft Sight Gauge 6 0/1828 ½ M BSP 3/8 F BSP x 10mm Compression 3/8 F BSP 40µ Aluminium CAF GEM4000 Gem Filter Service Kit 40µ CAF Push Button Royal Push Button See pages for ultrasonic gauges RELATE PRUCTS Visual REAING Push TYPE See pages for ultrasonic gauges RELATE PRUCTS K KERSENE Push Button Sight Level Gauge A cost effective push to read gauge to give an instant reading without compromising the tank contents, as when released the tank remains isolated esigned for fitting to bottom outlet steel & plastic tanks Quality corrosion resistant zinc plated brass body Economy push button model & more advanced Royal model with an integrated mesh filter & isolation valve so the gauge can be service without draining the tank Code escription Height (ft/mm) Inlet utlet Filter Tube Support Fluids RF6001 Royal Push Button 4ft Sight Gauge 4 0/1219 ½ M BSP ½ F BSP 100µ Aluminium CAF RF6007 Royal Push Button 6ft Sight Gauge 6 0/1828 ½ M BSP ½ F BSP 100µ Aluminium CAF PB1204 Push Button 4ft Sight Gauge 4 0/1219 ½ M BSP ½ F BSP Aluminium CAF PB1206 Push Button 6ft Sight Gauge 6 0/1828 ½ M BSP ½ F BSP Aluminium CAF PVC Tubing Tank Extension Piece 30m MAX CIL LENGTH 90mm TANK EXTENSIN PIECE K KERSENE K KERSENE IESEL IL Sight Level Gauge Accessories PVC Tubing - 30m coils or per foot For retrofitting sight gauges or for replacing weathered tubing Aluminium Tank Extension Piece esigned to fix into the bottom outlet of a plastic tank with dished ends, allowing the gauge to be used with any type of tank Code escription Length Inlet utlet Fluids SG1003 Sight Gauge PVC Tubing 30m Coil 100 Foot (30m) CAF SG1001 Sight Gauge PVC Tubing Per Foot 1 Foot CAF SG1114 4ft Alloy C Section & PVC Tubing 4 Foot CAF SG1032 6ft Alloy C Section & PVC Tubing 6 Foot CAF KAL9000 Aluminium Plastic Tank Extension Piece 90mm 1" M BSPT ½ F BSP CAF IESEL IL 106

106 Contents \ Filters & e-aerators CNITINERS 115 FILTERS & E-AERATRS FUEL FILTERS WIRE MESH E-AERATRS 114 CNITINERS 115 FILTRATIN UNITS 116 FUEL FILTERS E-AERATRS 114 WIRE MESH FILTRATIN UNITS

107 Filters & e-aerators / Fuel Filters Code escription Micron Max Flow Rate (lpm) 10-15µ MICRN 95lpm MAX FLW RATE Max Bar Inlet/ utlet 10µ MICRN 95lpm MAX FLW RATE IESEL B1 B100 B2 B20 GoldenRod Filters Fuel filter range widely recognised within the agricultural market Particle only and water & particle versions available Clear bowl containing paper cartridge with drain port for easy removal of filtered impurities Primarily used in gravity systems but also suitable for pump installations Complete kit contains one element, one head, bowl & gasket Spare Element CTJ1800 GoldenRod Particle nly 10µ F BSP CTJ1801 CTJ1818 CTJ1802 AT CTJ1809 GoldenRod Water & Particle 15µ F BSP CTJ1810 CTJ1818 CTJ1802 AT CTJ1815 GoldenRod BI-FLW Particle 10µ F BSP CTJ1816 CTJ1818 CTJ1802 AP CTJ1813 GoldenRod Wrench µ MICRN 95lpm MAX FLW RATE IESEL P PETRL B1 B100 Groz Filters Spare Head B2 B20 Spare Bowl Particle only and water & particle versions available Clear bowl containing paper cartridge with drain port for easy removal of filtered impurities Primarily used in gravity systems but also suitable for low flow pump installations Complete kit contains one element & one head Code escription Micron Max Flow Rate (lpm) Max Bar Inlet/utlet Spare Element Fluids GRZ03 Groz Particle nly 10µ F BSP GRZ04 Fluids AGT GRZ01 Groz Water & Particle 10µ F BSP GRZ02 AGT GRZ05 Groz Bio 10µ " F BSP AP IESEL B1 B100 GoldenRod Mesh Strainers Mesh strainer element designed for use with the GoldenRod bowl and head For removing large particles from fuel 40 mesh (381 micron) & 80 mesh (178 micron) versions available Stainless steel construction Code escription Mesh Micron Max Flow Rate (lpm) Max Bar Fluids CTJ1811 GoldenRod 40 Mesh Strainer µ AP CTJ1812 GoldenRod 80 Mesh Strainer µ AP 108

108 Fuel Filters \ Filters & e-aerators IESEL IESEL Piusi Particle Filter Particle only filter with resin coated paper element for removing debris out of fuel Spin-on cartridge for easy replacement once full Can be fitted to the suction or delivery of a pump installation ifferent flow rate versions depending upon requirements Complete kit contains one element & one head IESEL B2 B20 Piusi Clear Captor Particle only and water & particle versions available Clear bowl containing paper cartridge with drain port for easy removal of filtered impurities and easy visual inspection Can be fitted to the suction or delivery of a pump installation Complete kit contains two elements & one head Supplied in a point of sale display box Code escription Micron Max Flow Rate (lpm) IL P PETRL P PETRL B2 B20 Code escription Micron Max Flow Rate (lpm) Piusi Water Captor Water & particle filter with resin coated paper element for removing water & debris out of fuel Spin-on cartridge for easy replacement once full Max Bar Can be fitted to the suction or delivery of a pump installation ifferent flow rate versions depending upon requirements 70lpm kit contains two elements, 150lpm contains one element 10µ MICRN 100lpm MAX FLW RATE Inlet/utlet Spare Element Spare Head Fluids F A Piusi Particle 60lpm CF60 10µ F BSP Flanged F AFGT Piusi Particle 100lpm CF100 10µ F BSP Flanged CTH1813 AFGT Code escription Micron Max Flow Rate (lpm) Max Bar Max Bar Inlet/utlet 5-125µ 30µ MICRN 150lpm MAX FLW RATE Spare Element F00611A00 Piusi Water Captor 70lpm CF µ F BSP Flanged F CTH1801 AG F00611A10 Piusi Water Captor 150lpm CF µ F BSP Flanged F CTH1813 AG MICRN 100lpm MAX FLW RATE Inlet/utlet Spare Element Spare Head Fluids F00611B00 Piusi Clear Captor Particle nly 5µ F BSP Flanged F F AT F00611B10 Piusi Clear Captor Water & Particle 30µ F BSP Flanged F F AT F00611B60 Piusi Clear Captor Steel Mesh Particle 125µ F BSP Flanged F F AT Spare Head Fluids 109

109 Filters & e-aerators / Fuel Filters Code escription Micron Max Flow Rate (lpm) Code escription Micron Max Bar 14µ MICRN 150lpm MAX FLW RATE 10µ MICRN Max Flow Rate (lpm) 100lpm MAX FLW RATE Code escription Micron Max Flow Rate (lpm) Inlet/utlet Spare Element Spare Head Fluids CTH1830 Cim-Tek Hydrosorb 68lpm CT µ F BSP Flanged CTH1819 CTH1801 AG CTH1818 Cim-Tek Hydrosorb 110lpm CT µ F BSP Flanged CTH1817 CTH1813 AG 10µ MICRN 110lpm MAX FLW RATE Max Bar IESEL Cim-Tek Fuel Bowser Filter Filter specifically designed for fitting to fuel bowsers with high flow pumping systems Particle only and water & particle versions available Water & particle version is a shorter length design for when space is in issue but a higher flow, water filtration is required Both filters are supplied element only as bowser manufacturers often to manufacturer a custom head Compatible head available Max Bar Length Spare Head Fluids CTH1824 Cim-Tek Microglass Particle nly CT mm CTH1813 A CTH1825 Cim-Tek Hydroglass Water & Particle CT mm CTH1813 A IESEL B1 B100 Cim-Tek Hydroglass Bio Water & particle filter with high performance micro-glass element that traps debris & absorbs water out of biofuel Micro-glass media guarantees longer element life-span Spin-on cartridge for easy replacement once full Can be fitted to the suction or delivery of a pump installation ifferent flow rate versions depending upon requirements Complete kit contains one element & one head Inlet/utlet Spare Element F00611C00 Cim-Tek Bio Water & Particle 70lpm CT µ F BSP Flanged R CTH1801 AP F00611C10 Cim-Tek Bio Water & Particle 100lpm CT µ F BSP Flanged R CTH1813 AP IESEL P PETRL Cim-Tek Hydrosorb Water & particle filter with resin coated paper element for removing water & debris out of fuel Spin-on cartridge for easy replacement once full Can be fitted to the suction or delivery of a pump installation ifferent flow rate versions depending upon requirements Complete kit contains one element & one head Spare Head Fluids 110

110 Fuel Filters \ Filters & e-aerators AB ABLUE Piusi 3 AdBlue Filter Particle filter specifically designed for removing debris & crystallisation from AdBlue AdBlue is a pure solution but contamination can occur during the filling/transferring process which can damage the vehicle s SCR system Highly efficient technopolymer filtering element within a protective polyamide casing Please note: It is recommended that the filter is changed once a year AB ABLUE Cim-Tek AdBlue Filter Particle filter specifically designed for removing debris & crystallisation from AdBlue AdBlue is a pure solution but contamination can occur during the filling/transferring process which can damage the vehicle s SCR system Stainless steel filter housing Complete kit contains one element, one head, bowl & gasket K KERSENE B1 B100 IESEL Heating il Canister Filter Canister filter designed for low flow pumped heating systems Removes particles down to 10µ Aluminium head with disposable spin on element n heating systems change element during annual service 70µ MICRN 40lpm MAX FLW RATE Code escription Micron Max Flow Rate (lpm) Max Bar Inlet/utlet Working Temperature Spare Element Fluids CTH1845 Piusi 3 AdBlue Filter 70µ M BSP -5c /+40c F J 10µ MICRN 35lpm MAX FLW RATE Code escription Micron Max Flow Rate (lpm) Max Bar Inlet/utlet Fluids CTH1821 Heating il Canister Filter CT µ ½ F BSP CPA 5µ MICRN 76lpm MAX FLW RATE Code escription Micron Max Flow Rate (lpm) Max Bar Inlet/utlet Spare Element Fluids CTH1846 Cim-Tek AdBlue Filter CT µ F BSP CTH1847 J 111

111 Filters & e-aerators / Wire Mesh Filters Alloy Plastic µ MICRN F BSP INLET Code escription Micron Max Pressure (bar) Max Working Temp Inlet/utlet Fluids MF6167 Alloy ¼ Bowl Filter 100µ 2 90 c ¼ F BSP CA MF6160 Alloy ⅜ Bowl Filter 40µ 2 90 c ⅜ F BSP CA MF6172 Alloy ½ Bowl Filter 100µ 2 90 c ½ F BSP CA MF6179 Plastic il Filter & Water Separator 60µ 2 50 C ⅜ F BSP AFCM 50µ MICRN F x Comp Code escription Micron Max Flow Rate (lph) Inlet/utlet Fluids INLET ARMKIT Filter Assembly Kit 50µ 151 ½ F x 10mm Comp CA 100µ MICRN F BSP Flanged Code escription Micron Inlet/utlet Priming evice Fluids INLET K KERSENE Heating il Bowl Filter Inline particle filter designed for removing debris from small bore fuel lines such as domestic oil heating systems Choice or alloy constructed or clear plastic bowl Clear plastic version also removes water & has a drain port for easy removal of the filtered out water Alloy available in a number of thread sizes depending upon the individual installation K KERSENE 8950 Angle Filter 100µ 1 F BSP Flanged AF R Angle Filter Housing c/w Priming evice 1 F BSP Flanged 2m x 8mm Tubing AF R Replacement Element 100µ AF IESEL IESEL il Tank Filter Assembly Kit il tank filter with lever action isolation valve for removing debris from heating oil systems Comes with everything required to quickly & simply install the filter within the system 1 x ½ conical fitting & plastic pipe insert Includes reel of PTFE tape utlet 10mm compression Connects to the bottom outlet of the tank IESEL IL IL Angle Filters B3 B30 Alloy angle filter designed to be fitted to inlet side of an installation to remove large debris & protect pump components Can also be used to change inlet/outlet orientation, reduce the obstruction size of a 90 connection & reduce system pressure Priming device version available with no filter as standard Removable wire mesh filter, with replacement element available 112

112 Wire Mesh Filters \ Filters & e-aerators IESEL IESEL IL Y Strainers Inline Y strainers to filter out large debris to protect pump components Includes a drain point to allow for the easy removal of filtered impurities Brass & stainless steel versions available in a range of sizes depending upon installation esigned for basic filtration & advised to be used alongside a particle filter µ MICRN F BSP Code escription Micron Body Inlet/utlet Fluids AB3022 ½ Brass Y Strainer 600µ Brass ½ F BSP AFI AB3023 ¾ Brass Y Strainer 600µ Brass ¾ F BSP AFI AB Brass Y Strainer 600µ Brass 1 F BSP AFI AB ½ Brass Y Strainer 600µ Brass 1 ½ F BSP AFI AB Brass Y Strainer 600µ Brass 2 F BSP AFI BCS1038 ¾ Stainless Y Strainer 1200µ Stainless Steel ¾ F BSP N BCS Stainless Y Strainer 1200µ Stainless Steel 1 F BSP N IL W WATER W WATER ANY FLUI ANY FLUI Basket Strainers Basket strainers to filter out large debris to protect pump components esigned to be fitted in the suction line or to a non return valve on the suction side of a system Nylon & stainless steel versions available in a range of sizes depending upon installation esigned for basic filtration & advised to be used alongside a particle filter INLET See pages for particle filters RELATE PRUCTS 1000µ MICRN M BSP Code escription Micron Body Thread Inlet/utlet Fluids CIM3018 ⅜ Nylon Basket Strainer 1000µ Stainless Steel Nylon ⅜ M BSP AFI CIM3019 ½ Nylon Basket Strainer 1000µ Stainless Steel Nylon ½ M BSP AFI CIM3020 ¾ Nylon Basket Strainer 1000µ Stainless Steel Nylon ¾ M BSP AFI CIM Nylon Basket Strainer 1000µ Stainless Steel Nylon 1 M BSP AFI CIM ¼ Nylon Basket Strainer 1000µ Stainless Steel Nylon 1 ¼ M BSP AFI CIM ½ Nylon Basket Strainer 1000µ Stainless Steel Nylon 1 ½ M BSP AFI CIM Nylon Basket Strainer 1000µ Stainless Steel Nylon 2 M BSP AFI CIM ½ Nylon Basket Strainer 1000µ Stainless Steel Nylon 2 ½ M BSP AFI CIM Nylon Basket Strainer 1000µ Stainless Steel Nylon 3 M BSP AFI STRSS20 ¾ Stainless Basket Strainer 1000µ Stainless Steel Stainless Steel ¾ M BSP N STRSS25 1 Stainless Basket Strainer 1000µ Stainless Steel Stainless Steel 1 M BSP N INLET See pages for particle filters RELATE PRUCTS 113

113 Filters & e-aerators / e-aerators 230lph IL FLW 8lph CAPACITY K KERSENE IESEL B1 B100 TigerLoop il de-aerator for removing gas/air bubbles within an oil system Preheats oil using heat from the boiler room & from oil pump friction heat to give cleaner combustion & reduce oil consumption Single pipe design to ensure that any oil not required is re-circulated within the TigerLoop and not returned to the tank Combi models available with integrated particle filter Code escription il Flow (lph) Max Return il (lph) Capacity (lph) Max Working Temp Working Pressure (bar) Inlet/utlet Filter Fluids FL4009 TigerLoop c +0.5/-0.6 ¼ F BSP CA FL4020 TigerLoop Combi c +0.5/-0.6 ¼ F BSP 20µ CA FL4021 TigerLoop Bio c +0.5/-0.6 ¼ F BSP CAP FL4022 TigerLoop Bio Combi c +0.5/-0.6 ¼ F BSP 20µ CAP 220lph IL FLW 4lph CAPACITY K KERSENE IESEL Afriso e-aerator il de-aerator for removing gas/air bubbles within an oil system Single pipe design to ensure that any oil not required is not returned to the tank esigned to improve combustion & provides clean exhaust gases Code escription il Flow (lph) Max Return il (lph) Capacity (lph) Max Working Temp Working Pressure (bar) Inlet/utlet Fluids FL4010 3/K1 e-aerator c/w Transparent Bowl c +0.7/-0.5 ¼ F BSP CAT FL4011 3/M e-aerator c/w Metal Bowl c +0.7/-0.5 ¼ F BSP CAT 200lph IL FLW 5lph CAPACITY K KERSENE IESEL B2 B20 GK e-aerator il de-aerator for removing gas/air bubbles within an oil system Integrated particle filter & shut off valve Eliminawted multiple external connections to reduce the risk of leakage Can be used with fuel oil with a maximum of 20% fatty acid methyl ester Suitable for mounting indoors Code escription il Flow (lph) Max Return il (lph) Capacity (lph) Max Working Temp Working Pressure (bar) Inlet/utlet Filter Fluids GK GS Pro-Fi 3 FC c +0.5/-0.6 ⅜ F BSP 70µ CA e-aerator 114

114 Fuel Conditioners \ Filters & e-aerators IESEL Purafiner Fuel Conditioners Fuel conditioners designed to de-contaminate stored diesel Uses magnets to break down colonies of bacteria in a fuel tank caused by water contamination They reduce the bacteria into smaller sizes enabling it to pass through a standard filter, preventing your equipment & vehicles from damage that unfiltered bacteria causes ifferent sized & flow rate versions available FXT & ETA models are used within smaller installations e.g. pumps & generators ETS models are used within larger installations e.g. steel tanks & marine vessels IESEL B1 B100 IL P PETRL Cim-Tek Tank ryer esigned to be lowered into a fuel tank to check for and remove water contamination Contains a highly absorbent silica gel that can absorb up to 350ml of unwanted water Needs a 2 tank opening as the sock will expand to 40mm diameter when full Comes with a 2.2m retrieval cord for easily pulling out the used tank sock Trade counter display pack available c/w 12 tank dryers to encourage sales Please note: If the tank dryer finds water, it is advised to fit a water filter 650lpm MAX FLW RATE 10bar MAX PRESSURE See pages for water filters RELATE PRUCTS Code escription Seals Port Size Max Flow Rate (lpm) Max Pressure (bar) Body Fluids FXT10 FXT 3/8 Viton ⅜ F BSP Marine Aluminium A P FXT12 FXT ½ Viton ½ F BSP Aluminium A P ETA2000 ETA 1 Viton 1 F BSP Aluminium A P ETS1200 ETS ¾ ¾ F BSP Steel A P ETS2000 ETS 1 1 F BSP Steel A P ETS5000 ETS 2 2 F BSP Steel A P B1 B ml ABSRBS 2" TANK PENING See pages for water filters RELATE PRUCTS ETA ETS FXT Tank ryer Trade Counter Pack Code escription Tank ryers Absorber Length Cord Length Absorption Amount Min. Tank pening isplay Box Fluids CTS1901 Cim-Tek Tank ryer 1 590mm 2.2m 350ml 2 AFGP CTS1902 Cim-Tek Trade Counter Box mm 2.2m 350ml 2 o AFGP 115

115 Filters & e-aerators / Filtration Units 56lpm MAX FLW RATE AC/C PWER IESEL IL Piusi Filtroll Portable filtration unit for extracting fuel, removing impurities and then dispensing it into a container or vehicle Sturdy trolley unit with wheels and drip tray to prevent environmental damage c/w pump, delivery & suction hose, manual nozzle and nozzle support Stage one 30µ water filter & stage two 5µ particle filter for ensuring that maximum contaminants are removed Versions for diesel & oil available in a range of voltages depending upon requirements il version has maximum viscosity of 500cSt Code escription Max Flow Rate (lpm) V Filter Nozzle Hose Fluids F Filtroll 230v iesel µ Water + 5µ Particle Self m del, 3m suct A F Filtroll 230v il µ Water + 5µ Particle 1 Tube 3m del, 3m suct AF F Filtroll 12v iesel µ Water + 5µ Particle Self m del, 4m suct A F Replacement Particle Filter 5µ AF F Replacement Water Filter 30µ AF 25lpm MAX FLW RATE AC PWER IL Piusi epuroil Portable filtration unit for extracting oil, removing debris and then dispensing it into a container, or for recycling oils Sturdy trolley unit with wheels & a support holder for the dispensing valve c/w pump, delivery & suction hose 10µ particle filter & filter block warning gauge to alert when the filter element needs replacing esigned for cleaning waste oil tanks & used machinery oil so it can be reused Maximum viscosity of 500cSt ifferent voltage versions available Code escription Max Flow Rate (lpm) V Filter Nozzle Hose Fluids 50300A epuroil 230v µ Particle 1 Tube 2m del, 2m suct F 50302B epuroil 110v µ Particle 1 Tube 2m del, 2m suct F Replacement Filter 10µ Particle F 116

116 Contents \ Fill Point & Vent Equipment FILL PINT & VENT EQUIPMENT FILLER CAPS FILLER CAPS FILL PINTS 121 VENT CAPS & CWLS 122 FILL PINTS 121 VENT CAPS

117 Fill Point & Vent Equipment / Filler Caps Up to 4" SIZE F BSP CNNECTIN ANY FLUI Aluminium Filler Cap Robust filler cap designed to cap off the fill point of a tank or valve Prevents dripping and unwanted debris/water from entering into the tank's fill pipe Complete with chain and S ring to secure the cap to the male threaded fill pipe Two large lugs either side of the cap to enable easy application & removal Comes with either a leather or rubber sealing washer Available in a range of sizes depending on the installation requirements Code escription Material Seal Chain Threads Fluids MF ½ Aluminium Filler Cap Aluminium Leather Brass 1 ½ F BSP N MF Aluminium Filler Cap Aluminium Rubber Brass 2 F BSP N MF ½ Aluminium Filler Cap Aluminium Leather Brass 2 ½ F BSP N MF Aluminium Filler Cap Aluminium Rubber Brass 3 F BSP N MF Aluminium Filler Cap Aluminium Rubber Brass 4 F BSP N Up to 3" SIZE F BSP CNNECTIN ANY FLUI Brass Filler Cap Hardwearing filler cap designed to cap off the fill point of a tank or valve Prevents dripping and unwanted debris/water from entering into the tank's fill pipe Complete with chain and S ring to secure the cap to the male threaded fill pipe Lugs either side of the cap to enable application & removal (apart from 1 model) Comes with either a rubber, leather or synthetic sealing washer Available in a range of sizes depending on the installation requirements Code escription Material Seal Chain Threads Fluids MF Brass Filler Cap Brass Rubber 1 F BSP N MF ½ Brass Filler Cap Brass Leather 1 ½ F BSP N MF Brass Filler Cap Brass Synthetic Brass 2 F BSP N MF ½ Brass Filler Cap Brass Leather Brass 2 ½ F BSP N MF Brass Filler Cap Brass Leather Brass 3 F BSP N 118

118 Filler Caps \ Fill Point & Vent Equipment ANY FLUI 2" Plastic Filler Cap Cost effective filler cap designed to cap off the fill point of a tank or valve Prevents dripping and unwanted debris/water from entering into the tank's fill pipe Complete with chain and clip to secure the cap to the male threaded fill pipe Small lugs positioned around the cap to enable easy application & removal Stainless Steel Filler Cap Robust filler cap designed to cap off the fill point of a tank or valve Prevents dripping and unwanted debris/water from entering into the tank's fill pipe Complete with chain and clip to secure the cap to the male threaded fill pipe Small lugs positioned around the cap to enable easy application & removal Supplied with leather seal as standard, PTFE on request for use with aggressive fluids SIZE F BSP CNNECTIN Code escription Material Chain Threads Fluids MF Plastic Filler Cap Plastic Alloy 2 F BSP N ANY FLUI 2" Spinsecure Tank Lock Most secure tank lock on the market popular for domestic tanks Fits onto a tank s 2 fill point to secure the contents against theft Patented design means that when cap is locked it spins freely & is almost impossible to remove Padlock free-design with no torque points for crowbar entry High security numbered lock with over 50,000 combinations Simple fitting with no sealants, adhesives or tools required Adaptor available to allow use on 2 F threads SIZE F BSP CNNECTIN Code escription Material Seal Chain Threads Fluids MF Stainless Steel Filler Cap Stainless Steel Leather Stainless Steel 2 F BSP N IESEL IL K KERSENE 2" SIZE F BSP CNNECTIN Code escription Material Seal Keys Thread Fluids FSS750MF 2 Spinsecure Tank Lock Zinc Alloy NBR 3 2 F BSP AFC FSS750A 2 Spinsecure Tank Lock Adaptor Zinc Alloy NBR 2 M BSP AFC 119

119 Fill Point & Vent Equipment / Filler Caps Up to 4" SIZE F BSP CNNECTIN ANY FLUI Lockable Filler Cap Use with the lockable fill pipe adaptor to cap off & lock the fill point of a tank (see bottom of page) Adaptor fits onto the pipe thread & secured by a screw & the fill cap screws onto the adaptor The adaptor s bar is pushed up to prevent the cap from turning A padlock (not included) can be applied to keep the bar in position Cap & adaptor are sold separately Code escription Material Seal Threads Fluids AB Lockable Filler Cap ZA12 Alloy Leather 2 F BSP N AB ½ Lockable Filler Cap ZA12 Alloy Leather 2 ½ F BSP N AB Lockable Filler Cap ZA12 Alloy Leather 3 F BSP N AB Lockable Filler Cap ZA12 Alloy Leather 4 F BSP N 2" SIZE F BSP CNNECTIN ANY FLUI Lockable ip & Fill Cap Use with the lockable fill pipe adaptor to cap off & lock the fill point of a tank (see bottom of page) Comes with the additional facility to store a dipstick Adaptor fits onto the pipe thread & secured by a screw & the fill cap screws onto the adaptor The adaptor s bar is pushed up to prevent the cap from turning A padlock (not included) can be applied to keep the bar in position Cap & adaptor are sold separately Code escription Material Seal Threads Fluids AB Lockable ip & Fill Cap ZA12 Alloy Leather & Rubber 2 F BSP N AB ½ Lockable ip & Fill Cap ZA12 Alloy Leather & Rubber 2 ½ F BSP N AB Lockable ip & Fill Cap ZA12 Alloy Leather & Rubber 3 F BSP N AB Lockable ip & Fill Cap ZA12 Alloy Leather & Rubber 4 F BSP N Up to 4" SIZE F BSP CNNECTIN ANY FLUI Lockable Fill Pipe Adaptor Use with the lockable filler cap to cap off & lock the fill point of a tank Adaptor fits onto the pipe thread & secured by a screw & the fill cap screws onto the adaptor The adaptor s bar is pushed up to prevent the cap from turning A padlock (not included) can be applied to keep the bar in position Cap & adaptor are sold separately Code escription Material Seal Threads Fluids AB Lockable Fill Pipe Adaptor ZA12 Alloy Leather 2 F BSP x 2 M BSP N AB ½ Lockable Fill Pipe Adaptor ZA12 Alloy Leather 2 ½ F BSP x 2 ½ M BSP N AB Lockable Fill Pipe Adaptor ZA12 Alloy Leather 3 F BSP x 3 M BSP N AB Lockable Fill Pipe Adaptor ZA12 Alloy Leather 4 F BSP x 4 M BSP N 120

120 Fill Points \ Fill Point & Vent Equipment IESEL Straight Fill Point esigned to allow easy filling of large static tanks from ground level or from a remote location Aluminium fill point nipple with flat face for a good tanker fitting seal Brass fill cap to stop dripping & debris from entering (other fill cap material available) Lever ball valve & non return valve Comes complete with a four hole wall/cabinet mounting brackets Primarily purchased at the tank manufacturing stage for EM use Angled Fill Point esigned to allow easy filling of large static tanks from ground level or from a remote location Custom 45 fitting with flat face for a good tanker fitting seal Angled fill point means there is only a very small amount of disconnect dripping due to fuel being held within the 45 fitting Brass fill cap to prevent dripping & debris from entering (other fill cap material available) Lever ball valve & non return valve Comes complete with a four hole wall/cabinet mounting brackets Primarily purchased at the tank manufacturing stage for EM use 2" SIZE F BSP CNNECTIN Code escription Inlet utlet Length (mm) Height (mm) Fluids FP001 2 Straight Fill Point 2 M BSP 2 M BSP ACF IESEL IESEL K KERSENE K KERSENE K KERSENE IL IL IL Fill Point Nipple esigned to terminate the fill pipe on an above ground fuel tank Tanker connection end has a parallel thread & flat face for a good tanker fitting seal ther end has a tapered thread for connection to the valves & pipework Aluminium construction 2" SIZE F BSP CNNECTIN Code escription Inlet utlet Length (mm) Height (mm) Fluids FP002 2 Angled Fill Point 2 M BSP 2 F BSP ACF 2" SIZE M BSP/BSPT CNNECTIN Use with the filler caps on pages RELATE PRUCTS Code escription Inlet utlet Length (mm) Fluids FIL01 2 Fill Point Nipple 2 M BSPT 2 M BSP 78 ACF 121

121 Fill Point & Vent Equipment / Vent Caps & Cowls Plastic Combi Up to 2" SIZE Slip ver CNNECTIN See page 125 for PRV vent valves RELATE PRUCTS Up to 3" SIZE Slip ver CNNECTIN ANY FLUI Plastic Vent Caps esigned to fit over the male thread on the top of an above ground storage tank to provide ventilation Normally used on domestic heating oil storage tanks A screw is provided on the side of the cap to cut into the male thread on the tank to hold it in place Standard vent cap has a plastic mesh to stop external particles from entering the tank Combi vent model has a top thread for use with a float gauge 3 part vent cap simply snaps into a 2" pre-drilled hole in a plastic tank Code escription Material Connection Top Thread Mesh Fluids MF Plastic Vent Cap Plastic 2 Slip ver o N MF Plastic Combi Vent Cap Plastic 2 Slip ver 1 ½ F BSP N MF6178G 3 Part Plastic Vent Cap Plastic 2" pen Hole o N See page 125 for PRV vent valves RELATE PRUCTS Up to 2" SIZE F BSP CNNECTIN ANY FLUI Aluminium Vent Cowl esigned to fit over the male thread on the top of an above ground storage tank to provide ventilation Normally used on steel fuel storage tanks Code escription Material Connection Fluids MF Aluminium Vent Cowl Aluminium 2 Slip ver N MF ½ Aluminium Vent Cowl Aluminium 2 ½ Slip ver N MF Aluminium Vent Cowl Aluminium 3 Slip ver N See page 125 for PRV vent valves RELATE PRUCTS 3 lugs provided round the bottom of the cowl for direct fitting Allan key fitting in one of the lugs to help secure the cowl to the male thread on the tank ANY FLUI Aluminium Vent Cowl c/w Flameproof Screen esigned to fit over the male thread on the top of an above ground storage tank or breather riser on an underground tank Flameproof screen for use on steel fuel storage tanks containing flammable liquids ual thread for fitting to 1 ½ or 2 M BSP threads Conforms to BS EN Code escription Material Connection Fluids AB3191 ual Thread Flameproof Vent Cowl Aluminium 1 ½ F BSP & 2 F BSP N 122

122 Contents \ Valves VALVES SAFETY FIRE CHECK & FT ISLATIN IBC & RUM SAFETY ISLATIN CHECK & FT FIRE IBC & RUM

123 Valves / Safety Valves 15lph MAX FLW RATE 3 /8" F BSP INLET/UTLET Pressure Reducing Valve Pressure reducing valve designed for heating oil installations 3 way design for use on pumping or multiple appliances and systems with a liquid head over 40 metres Two ⅜ F BSP inlet/outlet ports and a ¼ F BSP pressure gauge port Adjustable outlet pressure range Code escription Inlet/utlet Max Inlet Pressure (bar) utlet Pressure (bar) Max Flow Rate (lph) Fluids FC11002 Pressure Reducing Valve ⅜ F BSP CFA 20lph MAX FLW RATE 10mm Compression INLET/UTLET K KERSENE K KERSENE GK Pressure Regulating Valve esigned for regulating the pressure in a single appliance gravity feed system Commonly used within oil heating systems with a liquid head range of 2-30 metres Fixed outlet pressure of 100mbar c/w 10mm compression ends Code escription Inlet/utlet Inlet Pressure (bar) utlet Pressure (mbar) Max Flow Rate (lph) Fluids FC11003 GK Pressure Regulating Valve 10mm Compression CFA 83lpm MAX FLW RATE 1½" F BSP INLET/UTLET IESEL IL IL P PETRL Pressure Regulating Anti-Syphon Valve esigned to avoid syphoning or accidental emptying of an above ground storage tank Prevents head loss & regulates the flow with no hammering effect Can be fitted either horizontally or vertically with a maximum liquid column of 6m Tri-flange connection allows valve to be serviced without disturbing the pipework Valve adjustment screw for adapting to the installation Possible to fit two valves in parallel for increased flow rate Code escription Inlet/utlet Max Flow Rate (lpm) Wire Mesh Filter Fluids N4049 Pressure Regulating Anti-Syphon Valve 1 ½ F BSP Flanged 83 o AGM IESEL IESEL B3 B30 124

124 Safety Valves \ Valves IESEL P PETRL PRV Vent Valves Pressure/vacuum valve with integrated poppet type valve esigned to prevent fuel vapours from escaping under normal operating conditions Metal version with aluminium body & Teflon coating, for fitting to top of risers on stage 1B vapour recovery systems & static tanks Plastic version with sealing o-ring & metal stem, for fitting to static & mobile storage tanks Metal version is tested to BS EN 12874:2001 Code escription Connection pening Pressure (vacuum to tank) 2" SIZE M or F BSP CNNECTIN pening Pressure (vent to atmosphere) MF6155 Metal Pressure/Vacuum Vent Valve 2 F BSP 2mb 35mb Teflon Coated Aluminium AG MF6154 Plastic Pressure/Vacuum Vent Valve 2 M BSP 17mb 137mb Plastic A IESEL W WATER Adjustable Pressure Relief Valve esigned for use with pumps that have no internal bypass valve Commonly sold alongside our engine driven pumps when a nozzle is used Working pressure is adjustable from 1 to 10 bar 1 and 2 versions available 1" to 2" SIZE F BSP CNNECTIN Code escription Connection Working Pressure (bar) Body Fluids CTS125EP 1 Adjustable Pressure Relief Valve 1 F BSP 1-10 Brass AIM CTS2500EP 2 Adjustable Pressure Relief Valve 2 F BSP 1-10 Brass AIM IESEL IL K KERSENE W WATER Pressure Relief Angle Check Valve Brass non return valve for keeping a pump s suction line primed Ensures the pressure from the fuel head is held back from the pump Can be used in conjunction with a hose reel as relief valve is incorporated F x F BSP threaded inlet/outlet 1½" to 2" SIZE F BSP CNNECTIN See page 129 for versions without pressure relief valve RELATE PRUCTS Code escription Inlet/utlet Body Safety Valve (bar) Valve Seat Fluids AB3135PRV 1½ Pressure Relief Angle Check Valve 1 ½ F BSP Brass 1.38 NBR AFCI AB3025PRV 2 Pressure Relief Angle Check Valve 2 F BSP Brass 1.38 NBR AFCI AB3135PR Pressure Relief Valve Poppet nly Brass 1.38 NBR AFCI Body Metal Plastic Fluids 125

125 Valves / Fire Valves 15m MAX CAPILLARY K KERSENE Remote Acting Fire Valve esigned to close off the oil supply to the burner in the event of a fire As a precaution, the valve will not reopen until the manual reset is activated Will not be able to reopen until temperature has fallen to 30 C Brass body c/w copper tube sensor & stainless steel piston Higher flow rate for more industrial applications Horizontal or vertical fitting Suitable for class C & fuels BSRIA & FTEC approved to E101 A fusible hand wheel version is available on request - please ask Code escription Capillary (m) Cutt-ff Temperature Inlet/utlet Flow Rate 2m Head Fluids MF6173 Remote Acting Fire Valve 1.5m 66 C C ⅜ F BSPT 395 CA MF6174 Remote Acting Fire Valve 3m 66 C 3 66 C ⅜ F BSPT 395 CA MF6175 Remote Acting Fire Valve 6m 66 C 6 66 C ⅜ F BSPT 395 CA MF6176 Remote Acting Fire Valve 9m 66 C 9 66 C ⅜ F BSPT 395 CA MF6177 Remote Acting Fire Valve 15m 66 C C ⅜ F BSPT 395 CA MF61739 Remote Acting Fire Valve 1.5m 90 C C ⅜ F BSPT 395 CA MF61749 Remote Acting Fire Valve 3m 90 C 3 90 C ⅜ F BSPT 395 CA MF61759 Remote Acting Fire Valve 6m 90 C 6 90 C ⅜ F BSPT 395 CA MF61769 Remote Acting Fire Valve 9m 90 C 9 90 C ⅜ F BSPT 395 CA 3 /8" F BSPT INLET/UTLET See page 173 for fire valve tester RELATE PRUCTS 16m MAX CAPILLARY 1 /4" F BSPT INLET/UTLET See page 173 for fire valve tester RELATE PRUCTS K KERSENE Teddington KBB Fire Valve Tried & tested brand of fire valve used within domestic heating systems for over 40 years esigned to close off the oil supply to the burner in the event of a fire As a precaution, the valve will not reopen until the manual reset is activated Will not be able to reopen until temperature has fallen to 30 C Brass body c/w copper tube sensor Built in isolation valve for easier system servicing Suitable for use with biofuel up to B50 BSRIA & FTEC approved to E101 Code escription Capillary (m) Cutt-ff Temperature Inlet/utlet Flow Rate 1m Head Fluids MF6193 KBB Fire Valve 1.5m 65 C ¼ F BSPT 56 CA MF6195 KBB Fire Valve 3m 65 C 3 65 ¼ F BSPT 56 CA MF6196 KBB Fire Valve 6m 65 C 6 65 ¼ F BSPT 56 CA MF6197 KBB Fire Valve 9m 65 C 9 65 ¼ F BSPT 56 CA MF6198 KBB Fire Valve 16m 65 C ¼ F BSPT 56 CA MF6194 KBB Fire Valve 2m 90 C 2 90 ¼ F BSPT 56 CA IESEL IESEL 126

126 Fire Valves \ Valves K KERSENE CFV Fire Valve esigned to close off the oil supply to the burner in the event of a fire As a precaution, the valve will not reopen until the manual reset is activated Will not be able to reopen until temperature has fallen to 30 C Brass body c/w copper tube sensor Built in isolation valve FTEC & BSRIA approved to FS E101:1998 Must be installed according to BS5410 Part 1 6m MAX CAPILLARY 1 /4" F BSPT INLET/UTLET See page 173 for fire valve tester RELATE PRUCTS Code escription Capillary (m) Cutt-ff Temperature Inlet/utlet Flow Rate 2m Head Fluids MF6180 CPV Fire Valve 1.5m 65 C C ¼ F BSPT 85 CA MF6181 CPV Fire Valve 3m 65 C 3 65 C ¼ F BSPT 85 CA MF6182 CPV Fire Valve 6m 65 C 6 65 C ¼ F BSPT 85 CA MF6183 CPV Fire Valve 2m 90 C 2 90 C ¼ F BSPT 85 CA MF6184 CPV Fire Valve 3m 90 C 3 90 C ¼ F BSPT 85 CA MF6185 CPV Fire Valve 6m 90 C 6 90 C ¼ F BSPT 85 CA K KERSENE IESEL IESEL FS Thermostatic Fire Valves esigned to close off the oil supply to the burner in the event of a fire As a precaution, the valve will not reopen until the manual reset is activated Will not be able to reopen until temperature has fallen to 30 C Brass body c/w copper tube sensor FTEC & BSRIA approved to FS E101:1998 Must be installed according to BS5410 Part 1 1 versions are available on request - please ask 10m MAX CAPILLARY 1 /2" F BSPT INLET/UTLET See page 173 for fire valve tester RELATE PRUCTS Code escription Capillary (m) Cutt-ff Temperature Inlet/utlet Flow Rate 1.2m Head Fluids MF6200 FS Thermostatic Fire Valve 1.5m 72 C C ½ F BSPT 360 CA MF6201 FS Thermostatic Fire Valve 3m 72 C 3 72 C ½ F BSPT 360 CA MF6202 FS Thermostatic Fire Valve 6m 72 C 6 72 C ½ F BSPT 360 CA MF6203 FS Thermostatic Fire Valve 10m 72 C C ½ F BSPT 360 CA MF6205 FS Thermostatic Fire Valve 3m 95 C 3 95 C ½ F BSPT 360 CA MF6206 FS Thermostatic Fire Valve 6m 95 C 6 95 C ½ F BSPT 360 CA 127

127 Valves / Check & Foot Valves 3 /8" to 4" SIZE F BSP CNNECTIN IESEL IL K KERSENE CIM 30K Check Valve Brass, spring loaded non return valve to allow flow in only one direction Suitable for vertical, horizontal or oblique pipelines esigned for heating, compressed air, fuel & pump installations PN20 pressure rating W WATER F x F BSP threaded inlet/outlet Available in a range of sizes Code escription Inlet/utlet Body Spring Pressure (bar/psi) Valve Seat Fluids CIM3007 ⅜ CIM 30K NRV ⅜ F BSP Brass Stainless Steel 0.025/0.36 Viton AFCI CIM3008 ½ CIM 30K NRV ½ F BSP Brass Stainless Steel 0.025/0.36 Viton AFCI CIM3009 ¾ CIM 30K NRV ¾ F BSP Brass Stainless Steel 0.025/0.36 Viton AFCI CIM CIM 30K NRV 1 F BSP Brass Stainless Steel 0.025/0.36 Viton AFCI CIM ¼ CIM 30K NRV 1 ¼ F BSP Brass Stainless Steel 0.025/0.36 Viton AFCI CIM ½ CIM 30K NRV 1 ½ F BSP Brass Stainless Steel 0.025/0.36 Viton AFCI CIM CIM 30K NRV 2 F BSP Brass Stainless Steel 0.025/0.36 Viton AFCI CIM ½ CIM 30K NRV 2 ½ F BSP Brass Stainless Steel 0.025/0.36 Viton AFCI CIM CIM 30K NRV 3 F BSP Brass Stainless Steel 0.025/0.36 Viton AFCI CIM CIM 30K NRV 4 F BSP Brass Stainless Steel 0.025/0.36 Viton AFCI 1" to 1 1 /2" SIZE M x F BSP CNNECTIN IESEL IL K KERSENE Brass MxF Check Valve Brass, spring loaded non return valve to allow flow in only one direction Suitable for vertical, horizontal or oblique pipelines esigned for heating, compressed air, fuel & pump installations M x F BSP threaded inlet/outlet KIWA, WRC, NF, VGW approved (CIM models only) PN16 pressure rating Code escription Inlet/utlet Body Spring Pressure (bar/psi) Valve Seat Fluids CIM1016 ½ CIM 32K NRV ½ M x ½ F BSP Brass Stainless Steel 0.01 / 0.14 Viton AFCI CIM1017 ¾ CIM 32K NRV ¾ M x ¾" F BSP Brass Stainless Steel 0.01 / 0.14 Viton AFCI CIM CIM 32K NRV 1 M x 1 F BSP Brass Stainless Steel 0.01 / 0.14 Viton AFCI CIM ½ CIM 32K NRV 1 ½ M x 1 ½ F BSP Brass Stainless Steel 0.01 / 0.14 Viton AFCI CTS1021 2" MXF NRV 2" M x 2" F BSP Brass Stainless Steel 0.01 / 0.14 Viton AFCI W WATER 128

128 Check & Foot Valves \ Valves IESEL IL K KERSENE W WATER Brass Check Valve Brass, spring loaded non return valve to allow flow in only one direction Suitable for vertical, horizontal or oblique pipelines Streamline body popular in fuel & oil installations F x F BSP threaded inlet/outlet Available in a range of sizes PN40 (½ -¾ ) PN25 ( 1-1½ ) PN10 (2"-3 ) pressure rating Brass Angle Check Valve Brass non return valve for keeping a pump s suction line primed Ensures the pressure from the fuel head is held back from the pump F x F BSP threaded inlet/outlet To choose correct spring pressure (psi) measure from the ground level to the top of the tank 6ft= 3psi / 8ft=4psi / 10ft=4.5psi / 12ft=6psi 1 /2" to 2 1 /2" SIZE F BSP CNNECTIN Code escription Inlet/utlet Body Spring Pressure (bar/psi) Valve Seat Fluids CG3008 ½ Brass NRV ½ F BSP Brass Stainless Steel 0.025/0.36 NBR AFCI CG3009 ¾ Brass NRV ¾ F BSP Brass Stainless Steel 0.025/0.36 NBR AFCI CG Brass NRV 1 F BSP Brass Stainless Steel 0.025/0.36 NBR AFCI CG ¼ Brass NRV 1 ¼ F BSP Brass Stainless Steel 0.025/0.36 NBR AFCI CG ½ Brass NRV 1 ½ F BSP Brass Stainless Steel 0.025/0.36 NBR AFCI CG Brass NRV 2 F BSP Brass Stainless Steel 0.025/0.36 Viton AFCI CG ½ Brass NRV 2 ½ F BSP Brass Stainless Steel 0.025/0.36 NBR AFCI CG3015 3" Brass NRV 3" F BSP Brass Stainless Steel 0.025/0.36 NBR AFCI " Brass NRV c/w Pressure Relief Valve 1" F BSP Brass Stainless Steel 0.05/0.73 NBR AFCI IESEL P PETRL K W IL WATER 1 KERSENE /2" to 2" SIZE F BSP CNNECTIN See page 125 for version with pressure relief valve RELATE PRUCTS Code escription Inlet/utlet Body Spring Pressure (bar/psi) Valve Seat Fluids AB ½ Brass Angle Check Valve 1 ½ F BSP Brass NBR AFCI AB ½ Brass Angle Check Valve 1 ½ F BSP Brass Viton AGFCI AB ½ Brass Straight Check Valve 1 ½ F BSP Brass Viton AGFCI AB3028 2" Brass Angle Check Valve 2" F BSP Brass NBR AFCI AB Brass Angle Check Valve 2 F BSP Brass Viton AGFCI AB3026 2" Brass Straight Check Valve 2 F BSP Brass Viton AGFCI AB PSI Spring Steel 0.06/1 AFCI AB PSI Spring Steel 0.21/3 AFCI AB PSI Spring Steel 0.31/4.5 AFCI AB PSI Spring Steel 0.41/6 AFCI AB PSI Spring Steel 0.76/11 AFCI 129

129 Valves / Check & Foot Valves 3 /8" SIZE F BSP CNNECTIN K KERSENE il Check Valve Brass non return valve to allow flow in only one direction esigned for use in oil heating installations Valve comes complete with 8mm & 10mm pipe connectors F x F BSP threaded inlet/outlet Code escription Inlet/utlet Body Spring Pressure (bar/psi) Valve Seal Fluids FL4008 Brass NRV for il ⅜ F BSP Brass Stainless Steel 0.01/0.14 PM CFA 1" SIZE F BSP CNNECTIN IESEL IL IL K KERSENE Brass Foot Valve Brass spring loaded non return valve with plastic & stainless steel strainer Used on the suction side to ensure the fuel drawn up by the pump is free of large particles that could cause damage Economical option popular in fuel & oil installations F BSP threaded ends Code escription Inlet Body Spring Pressure (bar/psi) Valve Seal Fluids 7746C 1 Brass Foot Valve 1 F BSP Brass Stainless Steel 0.07/1.02 NBR AFCI 3 /4" to 1" SIZE F BSP CNNECTIN Piusi Vantage Locking Foot Valve Spring loaded non return valve with stainless steel strainer Used on the suction side to ensure the fuel drawn up by the pump is free of large particles The valve seat can be locked in position to stop diesel leaking out, making it ideal for portable pumping systems where the suction hose will be moved & stored Constructed of strong, anti-shock plastic material F BSP threaded ends Code escription Inlet Body Spring Pressure (bar/psi) Valve Seal Fluids F Piusi 1" Vantage Locking Foot Valve 1 F BSP Acetal Resin Stainless Steel 0.05/0.73 Viton AF F Piusi ¾" Vantage Locking Foot Valve ¾ F BSP Acetal Resin Stainless Steel 0.05/0.73 Viton AF IESEL IL IESEL W WATER 130

130 Check & Foot Valves \ Valves IESEL Piusi Plastic Check & Foot Valve Plastic, spring loaded non return valve to allow flow in only one direction Integrated relief valve to alleviate build up in the fuel line caused by thermal expansion or direct back pressure Heavy duty version for use in higher pressure lines Foot valve versions available complete with plastic & stainless steel strainer for removing large particles Stainless Steel Check & Foot Valve 316 Stainless steel, spring loaded non return valve to allow flow in only one direction Suitable for a wide range of fluids including fuels, AdBlue & chemicals that need to be kept free of material contamination ¾ and 1 models depending upon installation requirements Foot valve versions available complete with stainless steel strainer for removing large particles PN20 pressure rating 3 /4" to 1" SIZE BSP/Hose Tail CNNECTIN Code escription Inlet Body Spring Pressure (bar/psi) Valve Seal Strainer Fluids F Piusi Plastic NRV 1 F BSP Acetal Resin Stainless Steel 0.05/0.73 Viton AF F Piusi Plastic NRV (H) 1 F BSP Acetal Resin Stainless Steel 0.1/1.45 Viton AF F Piusi Plastic Foot Valve 1 Hose Tail Acetal Resin Stainless Steel 0.05/0.73 Viton o AF F ¾ Piusi Plastic Foot Valve ¾ Hose Tail Acetal Resin Stainless Steel 0.05/0.73 Viton o AF IESEL IL IL K KERSENE W WATER AB ABLUE C CHEMICAL 3 /4" to 1" SIZE F BSP CNNECTIN Check Valve Foot Valve Check Valve Foot Valve Code escription Inlet Body Spring Pressure (bar/psi) Valve Seal Strainer Fluids CVSS30420 ¾ Stainless Steel NRV ¾ F BSP Stainless Steel Stainless Steel 0.07/1.02 Viton AFCIJL CVSS Stainless Steel NRV 1 F BSP Stainless Steel Stainless Steel 0.07/1.02 Viton AFCIJL CTSSSFV001 ¾ Stainless Steel Foot Valve ¾ F BSP Stainless Steel Stainless Steel 0.07/1.02 Viton o AFCIJL CTSSSFV002 1 Stainless Steel Foot Valve 1 F BSP Stainless Steel Stainless Steel 0.07/1.02 Viton o AFCIJL 131

131 Valves / Isolation Valves 1 /4" to 4" SIZE F BSP CNNECTIN IESEL IL W WATER Yellow Handle Lever Ball Valve Italian manufactured nickel-plated full bore brass lever ball valve designed for starting/shutting off flow Popular within gas, water & fuel applications Steel handle, FP o-ring & PTFE seals PN40 (¼" - 1") PN32 (1¼ -2 ) PN16 (2½ 4 ) pressure rating PN20 (¼ -2 ) PN10 (2½ -4 ) pressure rating for gas applications WRAS & EN331:1998 gas approved Available in a range of sizes Code escription Inlet/utlet Thread epth (mm) Length (mm) Height (mm) Bore N (mm) Fluids AX ¼" FXF Brass Lever Ball Valve ¼ F BSP AFI AX ⅜" FXF Brass Lever Ball Valve ⅜ F BSP AFI AX ½" FXF Brass Lever Ball Valve ½ F BSP AFI AX ¾" FXF Brass Lever Ball Valve ¾ F BSP AFI AX " FXF Brass Lever Ball Valve 1 F BSP AFI AX ¼" FXF Brass Lever Ball Valve 1 ¼ F BSP AFI AX ½" FXF Brass Lever Ball Valve 1 ½ F BSP AFI AX " FXF Brass Lever Ball Valve 2 F BSP AFI AX ½" FXF Brass Lever Ball Valve 2 ½ F BSP AFI AX " FXF Brass Lever Ball Valve 3 F BSP AFI AX " FXF Brass Lever Ball Valve 4 F BSP AFI 1 /4" to 4" SIZE F BSP CNNECTIN IESEL IL W WATER G GAS G GAS Yellow Handle Lever Ball Valve Nickel-plated full bore brass lever ball valve designed for starting/ shutting off flow Popular within gas, water & fuel applications Steel handle, NBR o-ring & PTFE seals PN20 (¼ -2 ) PN10 (2½ -4 ) pressure rating WRAS & EN331:1998 gas approved Available in a range of sizes Code escription Inlet/utlet Thread epth (mm) Length (mm) Height (mm) Bore N (mm) Fluids AX ¼" FXF Brass Lever Ball Valve ¼ F BSP AFI AX ⅜" FXF Brass Lever Ball Valve ⅜ F BSP AFI AX ½" FXF Brass Lever Ball Valve ½ F BSP AFI AX ¾" FXF Brass Lever Ball Valve ¾ F BSP AFI AX " FXF Brass Lever Ball Valve 1 F BSP AFI AX ¼" FXF Brass Lever Ball Valve 1 ¼ F BSP AFI AX ½" FXF Brass Lever Ball Valve 1 ½ F BSP AFI AX " FXF Brass Lever Ball Valve 2 F BSP AFI AX ½" FXF Brass Lever Ball Valve 2 ½ F BSP AFI AX " FXF Brass Lever Ball Valve 3 F BSP AFI AX " FXF Brass Lever Ball Valve 4 F BSP AFI 132

132 Isolation Valves \ Valves IESEL IL W WATER Cimberio Red Handle Lever Ball Valve Italian manufactured nickel-plated full bore brass lever ball valve designed for starting/shutting off flow Popular in fuel, plumbing, heating & waterworks applications HNBR o-ring' & PTFE ball gaskets PN32 (¼ -2 ) PN20 (2½ -4 ) pressure rating Manufactured to EN IS9000 Available in a range of sizes 1 /4" to 4" SIZE F BSP CNNECTIN Code escription Inlet/utlet Thread epth (mm) Length (mm) Height (mm) Bore N (mm) Fluids LB4001 ¼ Fullway Red Ball Valve ¼ F BSP AFI LB4002 ⅜ Fullway Red Ball Valve ⅜ F BSP AFI LB4003 ½ Fullway Red Ball Valve ½ F BSP AFI LB4004 ¾ Fullway Red Ball Valve ¾ F BSP AFI LB Fullway Red Ball Valve 1 F BSP AFI LB ¼ Fullway Red Ball Valve 1 ¼ F BSP AFI LB ½ Fullway Red Ball Valve 1 ½ F BSP AFI LB Fullway Red Ball Valve 2 F BSP AFI LB ½ Fullway Red Ball Valve 2 ½ F BSP AFI LB Fullway Red Ball Valve 3 F BSP AFI LB Fullway Red Ball Valve 4 F BSP AFI IESEL IL Red Handle Lever Ball Valve Nickel-plated full bore brass lever ball valve designed for starting/ shutting off flow Popular in fuel, plumbing, heating &waterworks applications Steel handle, NBR o-ring & PTFE seals PN32 (¼" - 1") PN25 (1¼ -2 ) PN16 (2½ -4 ) pressure rating WRAS approved W WATER Available in a range of sizes 1 /4" to 4" SIZE F BSP CNNECTIN Code escription Inlet/utlet Thread epth (mm) Length (mm) Height (mm) Bore N (mm) Fluids AX ¼" FXF Brass Lever Ball Valve ¼ F BSP AFI AX ⅜" FXF Brass Lever Ball Valve ⅜ F BSP AFI AX ½" FXF Brass Lever Ball Valve ½ F BSP AFI AX ¾" FXF Brass Lever Ball Valve ¾ F BSP AFI AX " FXF Brass Lever Ball Valve 1 F BSP AFI AX ¼" Brass Lever Ball Valve 1 ¼ F BSP AFI AX ½" FXF Brass Lever Ball Valve 1 ½ F BSP AFI AX " FXF Brass Lever Ball Valve 2 F BSP AFI AX ½" FXF Brass Lever Ball Valve 2 ½ F BSP AFI AX " FXF Brass Lever Ball Valve 3 F BSP AFI AX " FXF Brass Lever Ball Valve 4 F BSP AFI 133

133 Valves / Isolation Valves 15-54mm SIZE Compression CNNECTIN IESEL IL W WATER Brass Compression Ball Valve Nickel-plated full bore brass lever ball valve designed for starting/ shutting off flow Popular choice within heating/plumbing applications Steel handle, NBR o-ring & PTFE seals Heavy duty industrial brass olives PN25 pressure rating Compression inlet/outlet WRAS & EN331:1998 gas approved Available in a range of sizes Code escription Inlet/utlet Thread epth (mm) Length (mm) Height (mm) Bore N (mm) Fluids AX mm Compression Brass Ball Valve 15mm mm AFI AX mm Compression Brass Ball Valve 22mm mm AFI AX mm Compression Brass Ball Valve 28mm mm AFI AX mm Compression Brass Ball Valve 35mm mm AFI AX mm Compression Brass Ball Valve 42mm mm AFI AX mm Compression Brass Ball Valve 54mm mm AFI 1 /2" to 1" SIZE M x F / F x F BSP CNNECTIN IESEL IL W WATER Brass Angle Ball Valve Chrome-plated 90 full bore brass lever angle ball valve designed for starting/shutting off flow EN331:1998 gas approved M x F or F x F options available Available in a range of sizes PN40 pressure rating Code escription Inlet/utlet Thread epth (mm) Length (mm) Height (mm) Bore N (mm) Fluids R780XL003 ½ M XF Angle Ball Valve ½ MXF BSP AFI R780XL004 ¾ MXF Angle Ball Valve ¾ MXF BSP AFI R780XL005 1 MXF Angle Ball Valve 1 MXF BSP AFI R783LX003 ½ FXF Angle Ball Valve ½ FXF BSP AFI R783LX004 ¾ FXF Angle Ball Valve ¾ FXF BSP AFI R783LX005 1 FXF Angle Ball Valve 1 F XF BSP AFI G GAS 134

134 Isolation Valves \ Valves IESEL IL W WATER Brass Lockable Lever Ball Valve Full bore brass lockable lever ball valve designed for starting/ shutting off flow Can be locked in the open or closed position using a padlock for security or safety (padlock not supplied) PN25 pressure rating F X F threaded inlet/outlet Available in a range of sizes 1 /2" to 3" SIZE F BSP CNNECTIN Code escription Inlet/utlet Thread epth (mm) Length (mm) Height (mm) Bore N (mm) Fluids LB5003 ½ Lockable Brass Ball Valve ½ F BSP AFI LB5004 ¾ Lockable Brass Ball Valve ¾ F BSP AFI LB Lockable Brass Ball Valve 1 F BSP AFI LB ½ Lockable Brass Ball Valve 1 ½ F BSP AFI LB Lockable Brass Ball Valve 2 F BSP AFI LB ½ Lockable Brass Ball Valve 2 ½ F BSP AFI LB Lockable Brass Ball Valve 3 F BSP AFI IESEL IL W WATER Stainless Steel Lockable Lever Ball Valve Full bore stainless steel lockable lever ball valve designed for starting/shutting off flow Can be locked in the open or closed position using a padlock for security or safety Suitable for more aggressive applications such as chemical or AdBlue pipelines 82 bar (½"-1") 62 bar (2 ) pressure rating F X F threaded inlet/outlet AB ABLUE Available in a range of sizes C CHEMICAL 1 /2" to 2" SIZE F BSP CNNECTIN Code escription Inlet/utlet Thread epth (mm) Length (mm) Height (mm) Bore N (mm) Fluids LB5015 ½ Lockable S/S Ball Valve ½ F BSP AFIJL LB6000 ¾ Lockable S/S Ball Valve ¾ F BSP AFIJL LB Lockable S/S Ball Valve 1 F BSP AFIJL LB Lockable S/S Ball Valve 2 F BSP AFIJL 135

135 Valves / Isolation Valves 1 /2" to 4" SIZE F BSPT CNNECTIN IESEL IL W WATER Brass Gate Valve Economy brass gate valve designed for starting/shutting off flow Used within fuel and water installations PN20 pressure rating BS5154 approved F X F BSPT threaded inlet/outlet Available in a range of sizes Code escription Inlet/utlet Length (mm) Height (mm) Bore N (mm) Fluids VT1317 ½ Brass Gate Valve ½ F BSP AFI VT1318 ¾ Brass Gate Valve ¾ F BSP AFI VT Brass Gate Valve 1 F BSP AFI VT ½ Brass Gate Valve 1 ½ F BSP AFI VT Brass Gate Valve 2 F BSP AFI VT ½ Brass Gate Valve 2 ½ F BSP AFI VT Brass Gate Valve 3 F BSP AFI VT Brass Gate Valve 4 F BSP AFI 1" SIZE M x F BSP CNNECTIN See page 67 for gravity hose kits RELATE PRUCTS IESEL IL W WATER Locking Angle Gate Valve Brass locking angle gate valve designed for starting/shutting off flow Primarily used on the bottom outlet of a gravity fed fuel tank Locking lever allows it to be padlocked when not in use (padlock not supplied) Pressed steel hand wheel for added strength & vandal resistance Used within fuel and water installations PN8 pressure rating M X F threaded inlet/outlet Code escription Inlet/utlet Length (mm) Height (mm) Bore N (mm) Fluids AB3046 Locking Angle Gate Valve 1 M x 1 F BSP AFI 136

136 Isolation Valves \ Valves IESEL IL W WATER Giacomini Brass Gate Valve Brass gate valve with aluminium alloy hand wheel designed for starting/shutting off flow Used within fuel and water installations PN16 pressure rating BS5154 approved F X F threaded inlet/outlet Available in a range of sizes IESEL IL W WATER Cimberio Brass Gate Valve Brass gate valve with aluminium alloy hand wheel for starting/ shutting off flow Used within fuel and water installations PN20 pressure rating BS5154 approved/kite mark KM F X F BSPT threaded inlet/outlet Available in a range of sizes 3 /8" to 4" SIZE F BSP CNNECTIN Code escription Inlet/utlet Length (mm) Height (mm) Bore N (mm) Fluids GT3401 ⅜ Brass Gate Valve ⅜ F BSP AFI GT3402 ½ Brass Gate Valve ½ F BSP AFI GT3403 ¾ Brass Gate Valve ¾ F BSP AFI GT Brass Gate Valve 1 F BSP AFI GT ¼ Brass Gate Valve 1 ¼ F BSP AFI GT ½ Brass Gate Valve 1 ½ F BSP AFI GT Brass Gate Valve 2 F BSP AFI GT ½ Brass Gate Valve 2 ½ F BSP AFI GT Brass Gate Valve 3 F BSP AFI GT Brass Gate Valve 4 F BSP AFI 1 /4" to 4" SIZE F BSPT CNNECTIN Code escription Inlet/utlet Length (mm) Height (mm) Bore N (mm) Fluids VT1280 ¼ Brass Gate Valve ¼ F BSPT AFI VT1281 ⅜ Brass Gate Valve ⅜ F BSPT AFI VT1282 ½ Brass Gate Valve ½ F BSPT AFI VT1283 ¾ Brass Gate Valve ¾ F BSPT AFI VT Brass Gate Valve 1 F BSPT AFI VT ¼ Brass Gate Valve 1 ¼ F BSPT AFI VT ½ Brass Gate Valve 1 ½ F BSPT AFI VT Brass Gate Valve 2 F BSPT AFI VT ½ Brass Gate Valve 2 ½ F BSPT AFI VT Brass Gate Valve 3 F BSPT AFI VT Brass Gate Valve 4 F BSPT AFI 137

137 Valves / Isolation Valves F BSP CNNECTIN IESEL IL W WATER Brass Normally Closed Solenoid Valve Normally closed solenoid valve meaning flow is shut off until activated When internal coil is energised, the valve is activated and opens to allow liquid flow esigned for applications where fluid only needs to be released on occasions Brass body & NBR diaphragm suitable for fuels, oils & water irect acting; no pressure needs to be applied to operate Screwed BSP F x F 100% duty coil supplied with wiring cap Code escription Inlet/utlet V Pressure (bar) Max. Temperature Length (mm) Bore N (mm) Fluids AX ½ Brass Solenoid Valve 230v ½ F BSP C AFIE AX ¾ Brass Solenoid Valve 230v ¾ F BSP * 80 C AFIE AX Brass Solenoid Valve 230v 1 F BSP * 80 C AFIE AX ½ Brass Solenoid Valve 24v ½ F BSP C AFIE AX ¾ Brass Solenoid Valve 24v ¾ F BSP * 80 C AFIE AX Brass Solenoid Valve 24v 1 F BSP * 80 C AFIE *When used with light oils, working pressure is at the lower rate 1 /2" to 1" SIZE 1 /2" to 1" SIZE F BSP CNNECTIN IESEL IL W WATER Stainless Normally Closed Solenoid Valve Normally closed solenoid valve meaning flow is shut off until activated When internal coil is energised, the valve is activated and opens to allow liquid flow esigned for applications where fluid only needs to be released on occasions Stainless steel body & viton diaphragm suitable for AdBlue, chemicals, fuels & water irect acting; no pressure needs to be applied to operate Screwed BSP F x F AB ABLUE C CHEMICAL 100% duty coil supplied with wiring cap Code escription Inlet/utlet V Pressure (bar) Max. Temperature Length (mm) Bore N (mm) Fluids AX ½ S/S Solenoid Valve 230v ½ F BSP * 80 C AFIJLE AX ¾ S/S Solenoid Valve 230v ¾ F BSP * 80 C AFIJLE AX S/S Solenoid Valve 230v 1 F BSP * 80 C AFIJLE AX ½ S/S Solenoid Valve 24v ½ F BSP * 80 C AFIJLE AX ¾ S/S Solenoid Valve 24v ¾ F BSP * 80 C AFIJLE AX S/S Solenoid Valve 24v 1 F BSP * 80 C AFIJLE AIR AIR AIR AIR *When used with light oils, working pressure is at the lower rate 138

138 rum & IBC Valves \ Valves IESEL Alloy rum Tap Alloy drum tap for dispensing small quantities of oil from 205ltr drums esigned to be secured onto the drum outlet when in the horizontal position Simple and easy to install option Non-locking & locking versions to prevent accidental opening of the drum outlet Brass rum Tap Brass drum tap for dispensing small quantities of oil from 205ltr drums esigned to be secured onto the drum outlet when in the horizontal position Simple and easy to install option Self-closing mechanism for safety and convenience Plastic rum Tap Plastic drum tap for dispensing oil from 205ltr drums esigned to be secured onto the drum outlet when in the horizontal position Simple and easy to install option Larger drum tap for the dispensing of larger volumes of fluid 3 /4" M BSPT Code escription Inlet Type Material Fluids MF3166 Alloy rum Tap Non-Locking ¾ M BSPT Non-Locking Alloy AF MF3167 Alloy rum Tap Locking ¾ M BSPT Locking Alloy AF IESEL IESEL IL IL IL Alloy MATERIAL INLET Brass MATERIAL 3 /4" M BSPT Code escription Inlet Type Material Fluids MF6145 Brass rum Tap Self-Closing ¾ M BSPT Self-Closing Brass AF W WATER C CHEMICAL INLET Plastic MATERIAL 2" M BSPT Code escription Inlet Type Material Fluids MF3171 Plastic rum Tap Non-Locking 2 M BSPT Non-Locking Plastic AFIL INLET 139

139 Valves / rum & IBC Valves 1" F BSP UTLET 2" M BSP RUM CNNECTIN 3 /4" M BSP UTLET CS/SEC INLET Piusi rum Connectors esigned for connecting a pump to a drum or tank Thanks to flanged connection sealing paste or Teflon is not required Integral filter for preventing large particles from entering the pump 1 F BSP inner thread for connection to a suction pipe Integrated check valve with a flange connection option Code escription rum Connector uter Thread Inlet Inner Thread utlet Valve Fluids F Piusi rum Connector c/w Valve 2 M BSP 1 F BSP 1 F BSP o AFGC F Piusi rum Connector c/w Valve & Flange 2 M BSP 1 F BSP 1 F BSP Flanged o AFGC See page 73 for down tubes RELATE PRUCTS IESEL AB ABLUE Piusi SEC IBC Connector esigned to connect the suction side of an AdBlue system to an IBC or drum pen/close twist mechanism that puts no angular pressure on the connection point nce connected prevents contamination of the contents CS inlet connection for the connection of a down tube ¾ M outlet version or one complete with 90 19mm hose tail AB ABLUE IL C CHEMICAL P PETRL K KERSENE Code escription Inlet utlet Fluids F Piusi SEC IBC Connector CS/SEC ¾ M BSP JI F153390HT Piusi SEC IBC Connector CS/SEC 90 19mm Hose Tail JI 1" F BSP UTLET Micromatic INLET Micromatic ispensing Coupler esigned to connect the suction side of an AdBlue system to an IBC or drum Lever operated valve opening/closing nce connected prevents contamination of the contents ry disconnect emptying with less than 1ml residue Stainless steel construction Code escription Inlet utlet Fluids Micromatic Coupler Micromatic 1 F BSP JLI W WATER W WATER 140

140 Contents \ Hose & Pipe Fittings HSE & PIPE FITTINGS HSE TAILS & SWIVELS HSE CUPLINGS PIPE FITTINGS RUM & IBC FITTINGS CUPLINGS TAILS & SWIVELS RUM & IBC PIPE FITTINGS

141 Hose & Pipe Fittings / Hose Tails & Swivels Steel Version Brass Hose Tails Code escription Fluids E0037 Brass ½ M BSPT x ½ / 12mm Hose Tail N E0036 Brass ¾ M BSPT x ¾ / 19mm Hose Tail N E0035 Brass 1 M BSPT x 1 / 25mm Hose Tail N E0077 Brass 1 ¼ M BSPT x 1 ¼ / 25mm Hose Tail N E0078 Brass 1 ½ M BSPT x 1 ½ / 38mm Hose Tail N E0081 Brass 2 M BSPT x 2 / 50mm Hose Tail N Piusi Hose Tails Code escription Fluids 6437 ¾ M BSP x ¾ / 19mm Hose Tail c/w NBR Seals N 7768 ¾ M BSP x ¾ / 25mm Hose Tail c/w NBR Seals N M BSP x ¾ / 19mm Hose Tail c/w NBR Seals N M BSP x 1 / 25mm Hose Tail c/w NBR Seals N *Will be suipplied in either brass or steel material Stainless Steel Hose Tails Code escription Fluids BCS1028 S/S ¾ M BSPT x ¾ / 19mm Hose Tail N BCS1001 S/S 1 M BSPT x 1 / 25mm Hose Tail N BCS1002 S/S 2 M BSPT x 2 / 50mm Hose Tail N Stainless Steel & Steel Hose Tails with Swivels Code escription Fluids BCS1020 S/S 1 F BSP x ¾ / 19mm Hose Tail c/w Swivel & Viton Seals N BCS1046 S/S 1" F BSP 60 Cone x 25mm Hose Tail* N BCS1014 S/S ¾" F BSP 60 Cone x 19mm Hose Tail* N Steel ¾" F BSP 60 Cone x 19mm Hose Tail* N Steel 1" F BSP 60 Cone x 25mm Hose Tail* N *Used on the S/S & steel bare hose reels Aluminium Hose Tail Code escription Fluids E0040 Aluminium 1 M BSPT x 1 / 25mm Hose Tail N 142

142 Hose Tails & Swivels \ Hose & Pipe Fittings Piusi Brass/Steel Hose Swivel Code escription Fluids 8456 Nickel Plated Brass Swivel ½ F BSP x ½ M BSP AF 62000A Brass Swivel 1 F BSP x ¾ M BSP AF 62200A Brass Swivel 1 F BSP x 1 M BSP AF 62400A Steel Swivel ¾ F BSP x ¾ M BSP AF *High quality swivels recommended for use with Piusi dispensing equipment Hose Swivels Code escription Fluids CTS1930 Plated Steel ¾ M BSP x ¾ F BSP Swivel AF CTS1931 Plated Steel 1 M BSP x 1 F BSP Swivel AF CTS1932 Plated Steel ¾ M BSP x 1 F BSP Swivel AF PF3093 Aluminium/Brass Swivel 1 ½ F BSP x 1 ½ M BSP AF F S/S Swivel ¾ M BSP x 19mm Hose Tail N F S/S Swivel ¾ M BSP x 1 M BSP N Piusi Articulated Hose Swivels Code escription Fluids F Articulated Brass/Alloy Swivel 1 F BSP x 1 M BSP AF F Articulated Brass/Alloy Swivel ¾ F BSP x ¾ M BSP AF Z Swivel Grease Swivel Code escription Fluids GV9002 Z Style Grease Alloy Swivel ¼ F BSP x ¼ M BSP K 143

143 Hose & Pipe Fittings / Hose Tails & Swivels BP3000 Straight Hose Tail Code escription Fluids F Straight ¾" Hose Tail Push Fit - 2 Pack AF F Straight 1" Hose Tail Push Fit - 2 Pack AF BP Hose Tail Code escription Fluids F ¾" Hose Tail Push Fit AF F " Hose Tail Push Fit AF BP Flanged Elbow Code escription Fluids F " F BSP Flanged Elbow AF BP Elbow Code escription Fluids F " F BSP Elbow AF BP3000 Straight F Fitting Code escription Fluids F Straight ¾" F BSP Push Fit AF F Straight 1" F BSP Push Fit AF BP3000 Straight M Fitting Code escription Fluids F Straight 1" M BSP Push Fit AF 144

144 Hose Tails & Swivels \ Hose & Pipe Fittings IESEL Husky High Flow Swivel High flow swivel for use with nozzles when the maximum flow rate achievable needs to be guaranteed e.g.the Husky VIII nozzle For use with nozzles with flow rates up to 375lpm Multi-plane, full 360 spherical rotation for easy nozzle movement Raised stainless steel ball bearings for easy joint movement 75% less back pressure Aluminium, zinc & zinc plated body 375lpm MAX FLW RATE 1" M BSP INLET See page 85 for Husky VIII RELATE PRUCTS Code escription Max Flow Rate (lpm) Inlet utlet Fluids HU-6949 Husky High Flow Swivel M BSP 1 F BSP A ANY FLUI Hi-Grip Stainless Hose Clamps Hi-Grip hose clips made entirely of 18/8 marine quality stainless steel For hoses with 25mm to 35mm, meaning only one version needs to be stocked for a range of applications Suitable for salt water & other highly corrosive environments Lloyd s Register approved for marine, offshore & industrial use All parts certified to BS304 EN mm SIZES Stainless MATERIAL Code escription Sizes (mm) Construction Fluids SG1006 Hi-Grip Stainless Steel Hose Clamps /8 Marine Quality Stainless Steel N ANY FLUI Mikalor Supra W2 Hose Clamps Heavy duty hose clips for the most demanding of hose assemblies Swivelling bridge allows the clamp to be mounted in awkward applications without having to remove the hose Can be opened & fastened in place without dislodging other parts Bevelled edges to protect the hose from damage Stainless steel band, class 8.8 bolt, captive nut & spacer system Suitable for industrial, automotive & agricultural machinery hoses 25-37mm SIZES Stainless MATERIAL Code escription Sizes (mm) Construction Fluids SG0000 Mikalor Hose Clamp 25-27mm Stainless Steel Band/Steel Bolt N SG1000 Mikalor Hose Clamp 27-29mm Stainless Steel Band/Steel Bolt N SG0001 Mikalor Hose Clamp 29-31mm Stainless Steel Band/Steel Bolt N SG0002 Mikalor Hose Clamp 34-37mm Stainless Steel Band/Steel Bolt N 145

145 Hose & Pipe Fittings / Hose Couplings See page 158 for stub hoses RELATE PRUCTS IESEL Reconnectable Safe-T-Break Breaks off in the event of a vehicle driving off with the nozzle still in the tank Seals off the fuel flow on both sides to prevent spillages Instant closing, dual poppet check valve Can be reused & retains UL approval after reconnection Shock absorbing spring to reduce nuisance breaks ry reconnect o-ring to prevent fuel spill when reconnecting ATEX approved version available Code escription Inlet/utlet Body Separates at (lbs/n) Fluids HU-3385 Husky ¾ Reconnectable Safe-T-Break ¾ F BSP Aluminium 200 / AP HU-3076 Husky 1 Reconnectable Safe-T-Break 1 F BSP Aluminium 200 / AP HU-3076A Husky 1 Reconnectable Safe-T-Break ATEX 1 F BSP Aluminium 200 / APG See page 158 for stub hoses RELATE PRUCTS 3 /4" to 1" SIZE F BSP CNNECTIN IESEL B1 B100 P PETRL Non-Reconnectable Safe-T-Break Breaks off in the event of a vehicle driving off with the nozzle still in the tank Seals off the fuel flow on both sides to prevent spillages Instant closing, dual poppet check valve Lightweight, inexpensive & disposable after initial break ATEX approved version available Code escription Inlet/utlet Body Separates at (lbs/n) Fluids HU-2774 Husky ¾ Non-Reconnectable Safe-T-Break ¾ F BSP Zinc Alloy/Aluminium 300 / AP HU-2774A Husky ¾ Non-Reconnectable Safe-T-Break ATEX ¾ F BSP Zinc Alloy/Aluminium 300 / APG HU-6914 Husky 1 Non-Reconnectable Safe-T-Break 1 F BSP Zinc Alloy/Aluminium 300 / AP 3 /4" to 1" SIZE F BSP CNNECTIN AB ABLUE B1 B100 P PETRL AdBlue Reconnectable Safe-T-Break Breaks off in the event of a vehicle driving off with the nozzle still in the tank Seals off the AdBlue flow on both sides to prevent spillages Instant closing, dual poppet check valve Comes as standard with scuff guard Code escription Inlet/utlet Body Separates at (lbs/n) Fluids HU-8216 Husky 1 Reconnectable Safe-T-Break AdBlue 1 M BSP Stainless Steel 200 / J 1" SIZE M BSP CNNECTIN 146

146 Hose Couplings \ Hose & Pipe Fittings IESEL IL Camlock Fittings Camlock fittings are designed to quickly connect & disconnect hoses Aluminium gravity die cast construction When connected these couplings provide a leak-proof NBR seal No tools required for connection Interchangeable with other Camlock fittings made to MIL-C Male BSPT to BS21 / Female BSP to BS2779 Available in various configurations and different sizes depending upon the installation requirements ther materials available - please ask ust Cap ust Plug Part F Cam/ Cam Socket CAM TYPE BSP/ Hose Tail HSE CNNECTIN Part Part C Part A Part B Code escription Cam Type Hose Connection Fluids A100-A Part A - 1 M Camlock x 1 F BSP 1 M Camlock 1 F BSP AF A200-A Part A - 2 M Camlock x 2 F BSP 2 M Camlock 2 F BSP AF B100-A Part B - 1 F Camlock x 1 M BSPT 1 F Camlock 1 M BSPT AF B200-A Part B - 2 F Camlock x 2 M BSPT 2 F Camlock 2 M BSPT AF C100-A Part C - 1 F Camlock x 1 Hose Tail 1 F Camlock 1 Hose Tail AF C200-A Part C - 2 F Camlock x 2 Hose Tail 2 F Camlock 2 Hose Tail AF 100-A Part - 1 F Camlock x 1 F BSP 1 F Camlock 1 F BSP AF 100-P Part - Plastic 1" F Camlock x 1" F BSP 1" F Camlock 1" F BSP AF 200-A Part - 2 F Camlock x 2 F BSP 2 F Camlock 2 F BSP AF E100-A Part E 1 M Camlock x 1 Hose Tail 1 M Camlock 1 Hose Tail AF E200-A Part E 2 M Camlock x 2 Hose Tail 2 M Camlock 2 Hose Tail AF F100-A Part F 1 M Camlock x 1 M BSPT 1 M Camlock 1 M BSPT AF F200-A Part F 2 M Camlock x 2 M BSPT 2 M Camlock 2 M BSPT AF P100-A 1 Camlock ust Plug 1 M Plug AF P200-A 2 Camlock ust Plug 2 M Plug AF C100-A 1 ust Cap 1 F Camlock AF C200-A 2 ust Cap 2 F Camlock AF Part E 147

147 Hose & Pipe Fittings / Hose Couplings Coupler F BSP THREA IESEL IL H Series Compatible Quick Couplings Plated steel, general purpose quick release valved couplings Low pressure drop & instantly seals upon disconnection to prevent any leakages Compatible with Snap-Tite H & US-MIL-C Smooth jet valve design with a safety pin system to prevent accidental disconnection Temperature range -20 C/+100 C Coupler & nipple sold as separate parts Code escription Thread Type Seal Pressure (bar) Fluids CTS1040 H Series Compatible ½ Coupler ½ F BSP Coupler Viton 276 AF CTS1041 H Series Compatible ½ Nipple ½ F BSP Nipple Viton 276 AF CTS1042 H Series Compatible ¾ Coupler ¾ F BSP Coupler Viton 241 AF CTS1043 H Series Compatible ¾ Nipple ¾ F BSP Nipple Viton 241 AF CTS1044 H Series Compatible 1 Coupler 1 F BSP Coupler Viton 138 AF CTS1045 H Series Compatible 1 Nipple 1 F BSP Nipple Viton 138 AF Coupler Nipple Nipple 1 /2" to 1" SIZE 1 /2" to 1" SIZE F BSP CNNECTIN IESEL IL IS B Series Quick Couplings Plated steel, multi-purpose quick release valved couplings Instantly seals upon disconnection to prevent any leakages Compatible with Hansen HK, Parker 60, Rectus 71-76, Faster HNV & IS Series B -ring in the socket seals the connection to prevent leakage Temperature range -20 C/+180 C Coupler & nipple sold as separate parts Code escription Thread Type Seal Pressure (bar) Fluids CTS1050 IS B Series ½ Coupler ½ F BSP Coupler Viton 280 AF CTS1051 IS B Series ½ Nipple ½ F BSP Nipple Viton 280 AF CTS1052 IS B Series ¾ Coupler ¾ F BSP Coupler Viton 250 AF CTS1053 IS B Series ¾ Nipple ¾ F BSP Nipple Viton 250 AF CTS1054 IS B Series 1 Coupler 1 F BSP Coupler Viton 230 AF CTS1055 IS B Series 1 Nipple 1 F BSP Nipple Viton 230 AF 148

148 Hose Couplings \ Hose & Pipe Fittings IESEL Piusi HQC Couplings Hose quick release valved couplings including both coupler & nipple Larger inner bore that minimises resistance in presence of high flow rates making them ideal for diesel applications Red plastic caps to prevent any leakages Both plastic dust caps & plugs supplied Code escription Thread Type Seal Fluids F HQC Quick Release Coupling 1 F BSP Coupler & Nipple NBR AF IESEL Rail Flyte Coupler Bulk fuelling coupler commonly used on train rail car refuelling hoses Screw connect dry break valve for simple & spill-free connection to tank fill point urable forged steel handles for easy operator control High impact steel construction & Viton seals Unique hex socket fitting for easy installation AB ABLUE IL Code escription Inlet Flow Rate (lpm) Seal Fluids CTS2050 Rail Flyte Coupler 1 ½ F BSP Viton A Azure AdBlue Tank Coupler Coupler designed to fit on the fill point of an AdBlue tank Screw connect dry break valve for simple & spill-free connection to tanker refilling hose Interchangeable with many other types of coupling Stainless steel construction & FKM & EPM seals 1" SIZE F BSP CNNECTIN 650lpm MAX FLW RATE 1 1 /2" F BSP INLET 16 Bar MAX PRESSURE 2" F BSP CNNECTIN Code escription Connection Pressure (bar) Seal Fluids TU70AZ20SS Azure Tank Coupler 2 F BSP 16 FKM & EPM J 149

149 Hose & Pipe Fittings / Pipe Fittings Brass Hexagon Bush Code escription BF2003 Brass Hexagon Bush ⅜ M x ¼ F BSPT BF2005 Brass Hexagon Bush ½ M x ¼ F BSPT BF2006 Brass Hexagon Bush ½ M x ⅜ F BSPT BF2008 Brass Hexagon Bush ¾ M x ½ F BSPT BF2010 Brass Hexagon Bush 1 M x ½ F BSPT BF2011 Brass Hexagon Bush 1 M x ¾ F BSPT Brass/Steel Hex Nipple Code escription BF2021 Brass Hexagon Equal Nipple ¼ M BSPT BF2022 Brass Hexagon Equal Nipple ⅜ M BSPT BF2023 Brass Hexagon Equal Nipple ½ M BSPT BF2024 Brass Hexagon Equal Nipple ¾ M BSPT BF2025 Brass Hexagon Equal Nipple 1 M BSPT BF2029 Brass Hexagon Equal Nipple 2 M BSPT 7765 Steel Hexagon Equal Nipple 1 M BSP HRF001 Steel Hexagon Nipple 1" M BSPT x 1" M BSP 60 Cone HRF002 Steel Hexagon Nipple 1" M BSPT x ¾" M BSP 60 Cone Brass Plug Flanged Code escription BF2107 Brass Plug Flanged ⅛ M BSPT BF2049 Brass Plug Flanged 1/4 M BSPT BF2056 Brass Plug Flanged ¾ M BSPT BF2057 Brass Plug Flanged 1 M BSPT Brass Backnut Flanged Code escription BF2090 Brass Backnut Flanged ½ F BSP BF2092 Brass Backnut Flanged 1 F BSP Brass Elbow Code escription BF8120 Brass Elbow 1 M x F BSPT BF8027 Brass Elbow 2 M x F BSPT BF8117 Brass Elbow 2 F x F BSPT BF8118 Brass Elbow 1 F x F BSPT 7988 Heavy uty Plated Brass Elbow 1 M x F BSP F Heavy uty Plated Brass Elbow 1 F x F BSP 150

150 Pipe Fittings \ Hose & Pipe Fittings Brass Straight Equal Coupler Code escription CF mm Straight Equal Couplers CF mm Straight Equal Couplers Brass Straight C x M Coupler Code escription CF mm x ¼ BSPT Straight C x M Coupler CF mm x ⅜ BSPT Straight C x M Coupler CF mm x ½ BSPT Straight C x M Coupler CF mm x ½ BSPT Straight C x M Coupler Brass Straight Reducing Coupler Code escription CF mm x 8mm Straight Reducing Coupler CF mm x 10mm Straight Reducing Coupler Brass C x M Elbow Code escription CF mm x ½ Brass C x M BSP Elbow CF mm x ⅜ Brass C x M BSP Elbow CF mm x ¼ Brass C x M BSP Elbow Brass Equal Elbow Code escription CF mm Brass Equal Elbow Brass Equal Tee Code escription CF mm Brass Equal Tee C x C x C Brass Stop Ends Code escription CF8020A 10mm Brass Stop Ends CF mm Brass Stop Ends Brass lives Code escription CF mm lives 151

151 Hose & Pipe Fittings / Pipe Fittings Brass Flare Straight Code FLA1002 FLA2004 Brass Flare Straight x M Code FLA1000 FLA1001 FLA2000 FLA2001 FLA2002 escription Brass Flare Elbow x M Code FLA2005 FLA2006 Brass Flare Elbow Code FLA2007 Brass Flare Tee Code FLA2008 Brass Flare Nut Code FLA3000 FLA3001 Flare Tooling Kit Brass Flare Straight 8mm x 8mm Brass Flare Straight 10mm x 10mm escription Brass Flare Straight ¼ M BSPT x 8mm Brass Flare Straight ⅜ M BSPT x 8mm Brass Flare Straight ¼ M BSPT x 10mm Brass Flare Straight ⅜ M BSPT x 10mm Brass Flare Straight ½ M BSPT x 10mm escription Brass Flare Elbow ¼ M BSPT x 10mm Brass Flare Elbow ⅜ M BSPT x 10mm escription Brass Flare Elbow 10mm x 10mm escription Brass Flare Tee 15mm x 10mm x 10mm escription Brass Flare Nut 8mm Brass Flare Nut 10mm Code escription Measure Carry Box FLA4000 Flare Fitting Tooling Kit Imperial o 152

152 Pipe Fittings \ Hose & Pipe Fittings Stainless Steel Fittings All stainless steel fittings are class 150lb and made from CF8M (316) stainless steel material. The range is manufactured to conform to IS 4144 standard, and all threads are to IS 7-1 (IN2999) BSPP Female, BSPT Male. A strong and robust fitting option, suitable for many fluids. Stainless Steel Elbow M x F Code BCS1032 BCS1004 BCS1005 escription S/S Elbow ¾ M x F Stainless Steel Elbow F x F Code BCS1053 BCS1027 BCS1003 S/S Elbow 1 M x F S/S Elbow 2 M x F escription S/S Elbow ¾ F x F S/S Elbow 1 F x F Stainless Steel Hex Nipple Code BCS1035 BCS1007 BCS1006 BCS1054 BCS1008 BCS1055 S/S Elbow 2 F x F escription S/S Hex Nipple Equal ¾ M x M S/S Hex Nipple Equal 1 M x M S/S Hex Nipple Equal 2 M x M S/S Hex Nipple Reducing 1 x ½ M x M S/S Hex Nipple Reducing 1 x ¾ M x M S/S Hex Nipple Reducing 2 x 1 M x M Stainless Steel Hex Reducing Bush Code BCS1056 BCS1009 BCS1057 escription S/S Hex Bush Reducing 1 x ½ M x F S/S Hex Bush Reducing 1 x ¾ M x F S/S Hex Bush Reducing 2 x 1 M x F Stainless Steel Equal Tee Code BCS1036 BCS1023 BCS1058 escription S/S Equal Tee ¾ F S/S Equal Tee 1 F S/S Equal Tee 2 F 153

153 Hose & Pipe Fittings / Pipe Fittings Steel Socket Half Weldable F x F Code escription BC8099 ST Socket Half Weldable ¼ F x F BSP BC8090 ST Socket Half Weldable ½ F x F BSP BC8091 ST Socket Half Weldable ¾ F x F BSP BC8092 ST Socket Half Weldable 1 F x F BSP BC8094 ST Socket Half Weldable 1 ½ F x F BSP BC8095 ST Socket Half Weldable 2 F x F BSP BC8097 ST Socket Half Weldable 3 F x F BSP Steel Socket Full Weldable F x F Code escription BC9020 ST Socket Full Weldable ¼ F x F BSP BC9021 ST Socket Full Weldable ⅜ F x F BSP BC9022 ST Socket Full Weldable ½ F x F BSP BC9023 ST Socket Full Weldable ¾ F x F BSP BC9024 ST Socket Full Weldable 1 F x F BSP BC9026 ST Socket Full Weldable 1 ½ F x F BSP BC9027 ST Socket Full Weldable 2 F x F BSP BC9028 ST Socket Full Weldable 2 ½ F x F BSP BC9029 ST Socket Full Weldable 3 F x F BSP BC9030 ST Socket Full Weldable 4 F x F BSP Black Iron Union Code escription BC9013 BI Union 1 F x F BSP BC9014 BI Union 1 ½ F x F BSP BC9015 BI Union 2 F x F BSP Black Iron Elbow M x F Code escription BC8023 BI Elbow ½ M BSPT x F BSP BC8024 BI Elbow ¾ M BSPT x F BSP BC8025 BI Elbow 1 M BSPT x F BSP BC8026 BI Elbow 1 ½ M BSPT x F BSP BC8027 BI Elbow 2 M BSPT x F BSP Black Iron Elbow F x F Code escription BC8113 BI Elbow ½ F x F BSP BC8114 BI Elbow ¾ F x F BSP BC8115 BI Elbow 1 F x F BSP BC8116 BI Elbow 1 ½ F x F BSP BC8117 BI Elbow 2 F x F BSP BC7003 BI Bend Equal Elbow 1 M x M BSPT Black Iron Equal Tee F Code escription BC8033 BI Tee Equal ½ F BSP BC8034 BI Tee Equal ¾ F BSP BC8035 BI Tee Equal 1 F BSP BC8036 BI Tee Equal 1 ½ F BSP BC8037 BI Tee Equal 2 F BSP 154

154 Pipe Fittings \ Hose & Pipe Fittings Black Iron Hex Equal Nipple M x M Code escription BC8081 BI Hex Nipple Equal ¼ M x M BSPT BC8083 BI Hex Nipple Equal ½ M x M BSPT BC8085 BI Hex Nipple Equal 1 M x M BSPT BC8086 BI Hex Nipple Equal 1 ½ M x M BSPT BC8087 BI Hex Nipple Equal 2 M x M BSPT Black Iron Hex Reducing Nipple M x M Code escription BC6001 BI Hex Nipple Reducing ½ M x ⅜ M BSPT BC6002 BI Hex Nipple Reducing ¾ M x ½ M BSPT BC6003 BI Hex Nipple Reducing 1 M x ½ M BSPT BC6004 BI Hex Nipple Reducing 1 M x ¾ M BSPT BC6005 BI Hex Nipple Reducing 1 ½ M x 1 M BSPT BC6006 BI Hex Nipple Reducing 2 M x 1 ½ M BSPT Steel Barrel Nipple M x M Code escription BC9002 Barrel Nipple ½ M x M BSPT BC9003 Barrel Nipple ¾ M x M BSPT BC9004 Barrel Nipple 1 M x M BSPT BC9006 Barrel Nipple 1 ½ M x M BSPT BC9007 Barrel Nipple 2 M x M BSPT BC9008 Barrel Nipple 2 ½ M x M BSPT BC9009 Barrel Nipple 3 M x M BSPT Black Iron Reducing Bush M x F Code escription BC8041 BI Bush Reducing ½ M BSPT x ¼ F BSP BC8045 BI Bush Reducing ½ M BSPT x ⅜" F BSP BC8046 BI Bush Reducing 2 M BSPT x 1 F BSP BC8047 BI Bush Reducing ¾ M BSPT x ½ F BSP BC8049 BI Bush Reducing 1 M BSPT x ½ F BSP BC8050 BI Bush Reducing 1 M BSPT x ¾ F BSP BC8051 BI Bush Reducing 1 ½ M BSPT x 1 F BSP BC8053 BI Bush Reducing 2 M BSPT x 1 ½ F BSP Black Iron Plug M Code escription BC8060 BI Plug ¼ M BSPT BC8063 BI Plug ½ M BSPT BC8064 BI Plug ¾ M BSPT BC8065 BI Plug 1 M BSPT BC8067 BI Plug 1 ½ M BSPT BC8068 BI Plug 2 M BSPT Black Iron Socket Malleable F x F Code escription BC8005 BI Socket Malleable ½ F x F BSP BC8006 BI Socket Malleable ¾ F x F BSP BC8008 BI Socket Malleable 1 F x F BSP BC8010 BI Socket Malleable 2 F x F BSP 155

155 Hose & Pipe Fittings / Pipe Fittings F F F F F F Plastic Hose Tail Code escription Fluids F Plastic 1 M BSP x 19mm Hose Tail c/w HNBR Seals JLI F Plastic 1 F BSP x 19mm Hose Tail c/w Swivel & HNBR Seals JLI Plastic 1" M BSP x 25mm Hose Tail JLI Plastic ¾ M BSP x 19mm Hose Tail JLI Plastic 90 Hose Tail Code escription Fluids F Plastic 90 1 M BSP x 19mm Hose Tail c/w Swivel & HNBR Seals JLI F Plastic 90 1 F BSP x 19mm Hose Tail c/w Swivel & HNBR Seals JLI Plastic 90 ¾ F x 19mm Hose Tail JLI Plastic Straight Connectors Code escription Fluids F Plastic 1 F x F BSP Straight Socket JLI F Plastic 1" M BSP x 1" F BSP c/w Swivel JLI F Plastic 1" F BSP x ¾ M BSP c/w Swivel (K24 to Auto Nozzle) JLI F Plastic 1" M x M BSP Hex Nipple JLI Plastic 90 Socket Code escription Fluids F Plastic 1 F x F 90 Socket JLI Stainless Steel Hose Tails Code escription Fluids BCS1028 S/S ¾ M BSPT x ¾ / 19mm Hose Tail JLI BCS1020 S/S 1 F BSP x ¾ / 19mm Hose Tail c/w Swivel & Viton Seals JLI BCS1001 S/S 1 M BSPT x 1 / 25mm Hose Tail JLI BCS1002 S/S 2 M BSPT x 2 / 50mm Hose Tail JLI F S/S ¾ M BSP x ¾ / 19mm Hose Tail c/w Swivel & Viton Seals JLI Stainless Steel Socket Code escription Fluids F S/S 1 F x F Straight Socket JLI 156

156 Pipe Fittings \ Hose & Pipe Fittings IESEL Flanged Connections Flanges IL For securing connections between pumping system parts such as pumps, meters & filters 8 screw locations designed to take a M8 hex head nut/bolt Flanged Elbows Ideal for compact connection requirements or to change the orientation of an existing flange through 90 Each flanged side has a groove machined to take an o-ring or oval ring depending on connection -ring/val Ring -rings are for connecting the groove of flange to a flat surface without sealants val rings are for connecting two groove flanged items together without sealants Flanged Extension Kit Code escription Flange -Ring val Ring Round Bolt (M8x20) See table for flange fitting options INFRMATIN ual Flange Kit Round Bolt (M8x30) Flanged Elbow Hex Bolt (M8x30) Hex Nut (M8) Flange Set Screw (M8x50) R Flange Kit AF R ual Flange Kit AF R A Single Flange Kit AF Flange Kit for Flow Meter AF F Flange nly 1 AF R Flanged Elbow Kit AF CTS1910 Flanged Extension Kit (72mm) AF F12229 Flanged Tube 130mm x 67mm AF F12228 Flanged Tube 300mm x 67mm AF F12172 Flanged Tube 341mm x 67mm AF R val Ring 1 AF R Ring 2 AF F M8 x 20mm Round Head Bolt 1 AF BLT03 M8 x 30mm Round Head Bolt 1 AF BLT01 M8 x 30mm Hex Head Bolt 1 AF BLT02 M8 x 50mm HT Grub/Set Screw 1 AF Fluids 157

157 Hose & Pipe Fittings / Pipe Fittings Tri-Flange Connectors esigned for connection to floor mounted traditional dispenser pumps Manufactured from stainless steel with mild steel welded connections Maximum pressure rating of 3 bar Flexible Connectors esigned for joining misaligned pipework or for installations where expansion/contraction may occur ften used in forecourt pumping installations Manufactured from stainless steel with zinc plated steel ends Code escription Inlet utlet Length (inch/mm) Fluids CTS2040 Flexible Connector 1 M BSPT 1 M BSPT 6/150 N See page 146 for breakaway couplings RELATE PRUCTS Tri-Flange INLET 170mm MAX LENGTH 1" M BSPT 150mm MAX LENGTH 3 /4" to 1" 275mm MAX LENGTH IESEL Stub Hoses esigned as an alternative to metal flexible connectors for joining misaligned pipework ften used in conjunction with breakaway couplings on forecourt pumps Constructed of hard wall hose Code escription Inlet utlet Length (mm) Fluids PA360 ¾ Stub Hose 240mm ¾ M BSP ¾ M BSP 240mm A PA361 ¾ Stub Hose 260mm ¾ M BSP ¾ M BSP 260mm A PA362 1 Stub Hose 240mm 1 M BSP 1 M BSP 240mm A PA363 1 Stub Hose 275mm 1 M BSP 1 M BSP 275mm A SIZE SIZE ANY FLUI Code escription Inlet utlet Length (inch/mm) Fluids KFC6000 Tri-Flange x Tri-Flange 6 Tri-Flange Tri-Flange 6/150 N KFC6750 Tri-Flange x 1 ½ M BSP 6.75 Tri-Flange 1 ½ M BSP 6.75/170 N KFC6751 Tri-Flange x 1 ½ F BSP 6.75 Tri-Flange 1 ½ F BSP 6.75/170 N KFC4500 Tri-Flange x 1 ½ M BSP 4.5 Tri-Flange 1 ½ M BSP 4.5/115 N KFC4501 Tri-Flange x 1 ½ F BSP 4.5 Tri-Flange 1 ½ F BSP 4.5/115 N KFC4498 Tri-Flange Gasket N ANY FLUI 158

158 rum & IBC Fittings \ Hose & Pipe Fittings IESEL IL Piusi Quick rum Coupling Quick coupling designed for connecting a pump directly onto a drum 2 M BSP outer thread for connection to the drum 1 F BSP inner thread for connection to the suction hose 1 or ¾" M BSP outlet for screwing directly into the pump IESEL IL 2" BSP rum Adaptor rum adaptors designed to convert a specific drum thread to 2 BSP Enables the direct connection of a pump or tap Polypropylene construction Mauser & TRI-SURE versions available Code escription Inlet utlet Material Fluids A Mauser rum Adaptor Mauser 70 x 6 M 2 F BSP Polypropylene JAFIL TRI-SURE rum Adaptor TRI-SURE 56 x 4 M 2 F BSP Polypropylene JAFIL IBC Fitting Hose Tail Fits the bottom outlet of an IBC to convert a buttress thread to a hose tail fitting Enables the easy connection of dispensing equipment Polypropylene construction ¾ & 1 versions available W WATER 3 /4" or 1" M BSP 2" M BSP RUM CNNECTIN Code escription rum Connector uter Thread Inlet Inner Thread utlet Fluids 8930 Piusi Quick Coupling 1" 2" M BSP 1" F BSP 1" M BSP AF 9160 Piusi Quick Coupling ¾" 2" M BSP 1" F BSP ¾" M BSP AF F Piusi rum Connector 2 M BSP 1 F BSP 1 F BSP AFGC AB ABLUE AB ABLUE IESEL P PETRL IL K KERSENE W WATER C CHEMICAL C CHEMICAL UTLET 2" F BSP UTLET Mauser/ TRI-SURE RUM CNNECTIN 3 /4" to 1" Hose Tail UTLET 60 x 6 Buttress Code escription Inlet utlet Fluids IBF/075HT-PG IBC Fitting to ¾ Hose Tail 60 x 6 IN61 Buttress F ¾ Hose Tail JAFIL IBF/100HT-PG IBC Fitting to 1 Hose Tail 60 x 6 IN61 Buttress F 1 Hose Tail JAFIL INLET 159

159 Hose & Pipe Fittings / rum & IBC Fittings 1" to 2" CAM UTLET 60 x 6 Buttress INLET IBC Fitting CAM Fitting Fits the bottom outlet of an IBC to convert a buttress thread to a CAM fitting Enables the easy connection of dispensing equipment Polypropylene construction 1 & 2 versions available Code escription Inlet utlet Fluids 100A-IN-PG IBC Fitting to 1 CAM 60 x 6 IN61 Buttress F 1 CAM Male JAFIL 200A-IN-PG IBC Fitting to 2 CAM 60 x 6 IN61 Buttress F 2 CAM Male JAFIL 1" to 2" M BSP UTLET 60 x 6 Buttress INLET IBC Fitting Male BSP Fits the bottom outlet of an IBC to convert a buttress thread to a Male BSP fitting Enables the easy connection of dispensing equipment Polypropylene construction 1 & 2 versions available Code escription Inlet utlet Fluids IBF-100M-PG IBC Fitting to 1 M BSP 60 x 6 IN61 Buttress F 1 M BSP JAFIL IBF-200M-PG IBC Fitting to 2 M BSP 60 x 6 IN61 Buttress F 2 M BSP JAFIL 1" to 2" F BSP UTLET 60 x 6 Buttress INLET AB ABLUE AB ABLUE AB ABLUE IBC Fitting Female BSP Fits the bottom outlet of an IBC to convert a buttress thread to a Female BSP fitting Enables the easy connection of equipment such as water taps/ hose with suitable reducers Polypropylene construction 1 & 2 versions available Code escription Inlet utlet Fluids IBF/100FSWIV-PG IBC Fitting to 1 F BSP 60 x 6 IN61 Buttress Swivel F 1 F BSP JAFIL IBF/200F-PG IBC Fitting to 2 F BSP 60 x 6 IN61 Buttress F 2 F BSP JAFIL IESEL IESEL IESEL IL IL IL W WATER W WATER W WATER C CHEMICAL C CHEMICAL C CHEMICAL 160

160 Contents \ Waste il, Spill Control, Tools & Sealants WASTE IL, SPILL, TLS & SEALANTS WASTE IL SPILL CNTRL SEALANTS TLS WASTE IL SPILL CNTRL SEALANTS TLS

161 Waste il, Spill Control, Tools & Sealants / Waste il 10lpm MAX FLW RATE AC PWER Cambiaolio il Extractor Portable oil extraction unit for spill-free oil removal from vehicles Self priming, continuously operating oil pump 10ltr waste oil collection tank mounted on wheeled trolley 1.7m suction hose & 4 probe types with mounting position Probes insert into the dipstick port to suck out the oil from the engine sump 2 x semi-rigid probes 800mm x Ø 6mm or 8mm 2 x rigid probes 650mm x Ø 8mm or 9mm Integrated suction gauge to monitor the pump & alert of any potential blockages perating noise less than 70dB Code escription V Max Flow Rate (lpm) Probes Fluids 50000A Cambiaolio il Extractor F Vacubox Probe Kit 10lpm MAX FLW RATE AC PWER IL IL Vacubox il Extractor Wall mounted oil extraction unit for spill-free oil removal from vehicles Sucks oil from the engine sump via the dipstick port & then pumps the extracted waste oil into holding tanks Single button operation & automatically stops once oil has been extracted Integrated suction gauge to monitor pump & alarm light for potential blockages ptional Probe Kit 2 x semi-rigid probes 800mm x Ø 6mm or 8mm 2 x rigid probes 650mm x Ø 8mm or 9mm Code escription V Max Flow Rate (lpm) Inlet/utlet Probes Fluids F00500A00 Vacubox il Extractor ½ F BSP F R Vacubox Wall Mounting Kit F R Vacubox 2m Suction Hose Kit F R Vacubox Probe Kit 4 F 162

162 Waste il \ Waste il, Spill Control, Tools & Sealants IL Easy-rainer & Vacu-rainer Portable waste engine/transmission oil draining unit designed for use under vehicle lift Two versions available; Easy-drainer for gravity flow draining & Vacu-drainer for retrieving oil direct from the engine via air operated suction probes Height adjustable 8litre waste oil bowl c/w filter drain grill Transparent recovery viewer, air pressure gauge & suction probes (Vacu-drainer only) 90litre oil recovery tank on a wheel mounted trolley Tank level visual gauge for identifying recovery tank contents 2m discharge pipe & air inlet valve for emptying the contents of the recovery tank when full Code escription raining Type Bowl Capacity (l) Tank Capacity (l) Level Gauge Gravity/Air PWER ischarge Pipe Suction Pipe Probes Vacu-rainer Transparent Viewer F Easy-rainer 90 Gravity 8 90 o 2m F F Vacu-rainer 90 Air perated Suction 8 90 o 2m 2m o o F IL IESEL W WATER C CHEMICAL Waste il rainers Small, lightweight & portable waste oil container tanks Cost effective solution designed for the draining & containment of waste oil from vehicles c/w vent plug & oil drain cap for emptying once full Integrated carry handle for easy transportation of the container to where it needs to be emptied Available in different sizes; 6ltrs, 10ltrs or 12ltrs depending upon the individual requirement 12 litre version comes with a bigger drip pan & filter for removing large contaminants 12 Litres MAX CAPACITY Gravity Code escription Capacity (l) raining Type rip Pan Filter Fluids ER2007 Waste il rainer 6ltr 6 Gravity FAIL ER2008 Waste il rainer 10ltr 10 Gravity FAIL ER2009 Waste il rainer 12ltr 12 Gravity o o FAIL TYPE 6 Litre 12 Litre Fluids 163

163 Waste il, Spill Control, Tools & Sealants / Spill Control Absorbent pads FEATURE Stop it, Soak it & Scrap it with the Envirospill spill kit range Using your kit to deal with a spill... Stop the spill from spreading any further Immediately stop the source of the spill, and then use the absorbent socks to contain the spilt fluid and prevent it from spreading any further. When more than one sock is used they should overlap by approximately 30cm to ensure that there is no gap. Absorb the spill When the spillage is contained within a confined area, the absorbent pads should be laid out on top of the fluid. The pads should be left to absorb the spillage for two to three minutes or until they are fully saturated. Safe & proper disposal All used absorbents should be placed into the clearly marked disposal bag and secured using the tie provided. This should then be disposed of correctly in accordance with local waste disposal regulations. Ask about our customer branding options We can brand the bag insert with your logo and details free of charge, so your customers always know where to go for replacements. Chemical bag & tie Absorbent socks See page 165 for spill kits RELATE PRUCTS See page 166 for pads only RELATE PRUCTS EnviroSpill Spill Kit Range ANY FLUI All industrial sites where oils, fuels and chemicals are stored, delivered or handled, should have spill control products at hand ready to deal with a spill simply and quickly should they need to. EnviroSpill spill kits provide you with everything you need in a portable and easy to access bag, perfect for storage in confined storage areas, lorry cabs & work benches. il Suitable for oils, fuels, diesel & petroleum based liquids Maintenance Suitable for oils, solvents & water based liquids Chemical Suitable for acids, alkalis, solvents & AdBlue 164

164 Spill Control \ Waste il, Spill Control, Tools & Sealants IESEL EnviroSpill il Spill Kit Spill kit containing everything required to quickly deal with an oil spill in a portable & compact clip close carrier For all hydrocarbon based oils, fuels & petroleum based liquids Ideal for wherever fuels and oils are stored, delivered & handled 2 or 4 spill socks (depending on kit) for absorbing 7.5 litres each 5 or 10 spill pads (depending on kit) for absorbing 1.1litres each Blue waste bag & tie for proper disposal of used absorbents 20 or 40 Litres CAPACITY Can be floated on water making them ideal for where water & oil must be separated Code escription Capacity (l) Socks Pads isposal Bag & Tie Fluids SPL-KT-20 EnviroSpill il Spill Kit 20l o AFGCK SPL-KT-40 EnviroSpill il Spill Kit 40l o AFGCK ANY FLUI EnviroSpill Maintenance Spill Kit Spill kit containing everything required to quickly deal with a spill in a portable & compact clip close carrier For all industrial fluids, water based liquids, oils & mild chemicals A universal kit required by any factory, plant or industrial site 2 or 4 spill socks (depending on kit) for absorbing 7.5 litres each 5 or 10 spill pads (depending on kit) for absorbing 1.1litres each Blue waste bag & tie for proper disposal of used absorbents C CHEMICAL IL P PETRL K KERSENE GR GREASE EnviroSpill Chemical Spill Kit Spill kit containing everything required to quickly deal with a spill in a portable & compact clip close carrier For AdBlue, chemicals, acids, alkalis & solvents Ideal for wherever more aggressive fluids are stored, delivered & handled 1 or 2 spill socks (depending on kit) for absorbing 7.5 litres each 5 or 10 spill pads (depending on kit) for absorbing 0.5litres each Blue waste bag & tie for proper disposal of used absorbents il/fuel TYPE 20 or 40 litres CAPACITY Maintenance Code escription Capacity (l) Socks Pads isposal Bag & Tie Fluids SPL-MKT-20 EnviroSpill Maintenance Spill Kit 20l o N SPL-MKT-40 EnviroSpill Maintenance Spill Kit 40l o N AB ABLUE TYPE 10 or 20 litres CAPACITY Chemical TYPE Code escription Capacity (l) Socks Pads isposal Bag & Tie Fluids SPL-CKT-10 EnviroSpill Chemical Spill Kit 10l o LJ SPL-CKT-20 EnviroSpill Chemical Spill Kit 20l o LJ 165

165 Waste il, Spill Control, Tools & Sealants / Spill Control 120 litres CAPACITY IESEL EnviroSpill Eco il Absorbent Pads Box of 200 spill pads designed as a simple & cost effective solution for dealing with an oil spill For all hydrocarbon based oils, fuels & petroleum based liquids pen structure, melt blown polypropylene construction Absorb 0.6litres each - total box capacity is 120litres Ideal for wherever fuels and oils are stored, delivered & handled Can be floated on water making them ideal for where water & oil must be separated ANY FLUI IL P PETRL K KERSENE Code escription Pad Capacity (l) Pads Box Capacity (l) Fluids SPL-EPKT-200 EnviroSpill Eco il Spill Pads AFGCK il/fuel TYPE 120 litres CAPACITY il/fuel TYPE IESEL IL P PETRL K KERSENE GR GREASE EnviroSpill il Absorbent Pads Box of 200 spill pads designed as a durable solution for dealing with an oil spill For all hydrocarbon based oils, fuels & petroleum based liquids impled & bonded for extra strength so it to be used as a wipe Close bonded polypropylene with low-linting cover stock on both sides Absorb 0.6litres each - total box capacity is 120litres Ideal for wherever fuels and oils are stored, delivered & handled Can be floated on water making them ideal for where water & oil must be separated Code escription Pad Capacity (l) Pads Box Capacity (l) Fluids SPL-PKT-200 EnviroSpill il Spill Pads AFGCK 100 litres CAPACITY Maintenance TYPE GR GREASE EnviroSpill Maintenance Absorbent Pads Box of 200 spill pads designed as a durable solution for dealing with a spill For all industrial fluids, water based liquids, oils & mild chemicals impled & bonded for extra strength so it to be used as a wipe Close bonded polypropylene with low-linting cover stock on both sides Absorb 0.5litres each - total box capacity is 100litres Universal pads required by any factory, plant or industrial site Code escription Pad Capacity (l) Pads Box Capacity (l) Fluids SPL-MPKT-200 EnviroSpill Maintenance Spill Pads N 166

166 Spill Control \ Waste il, Spill Control, Tools & Sealants ANY FLUI EnviroSpill rum Pallet rum pallet for complying with oil storage regs & containing any spills to avoid any slip hazards or damage to the environment Sump can hold the contents of a 205litre drum in the event of a leak or rupture Forklift lifting points for easy manoeuvring Self-locating grates lift off for quick clean up Polyethylene construction resistant to chemicals & acids ptions designed for holding 2 or 4 drums il Gator Spill Absorbent Granules Absorbent granules designed for spreading over an oil spill For all hydrocarbon based oils, fuels & petroleum based liquids Encapsulates 2-6 times its weight Ideal for wherever fuels and oils are stored, delivered & handled Available in a number of sizes depending upon the requirement 250 or 284 litres CAPACITY Maintenance Code escription rum Number Sump Capacity (l) imensions (mm) Fluids SPL-PLT205-2 Envirospill 2 rum Spill Pallet x 635 x 457 N SPL-PLT205-4 Envirospill 4 rum Spill Pallet x 1245 x 260 N ANY FLUI EnviroSpill Spill Bins Portable two-wheeled, hinged lid bin containing everything required to quickly deal with a spill Ideal when a quantity of absorbents need to be taken to a spill site il only & maintenance versions for any fluids available in 120l & 240l 5 or 7 spill socks & 4 or 10 spill pillows (depending on kit) 60 or 150 spill pads (depending on kit) Blue waste bags & ties for proper disposal of used absorbents IESEL IL P PETRL K KERSENE GR GREASE TYPE 120 or 240 litres CAPACITY il/ Maintenance Code escription Capacity (l) Socks Pads Pillows isposal Bag & Tie Fluids SPL-BIN-120-IL Envirospill il Spill Bin 120l AFGCK SPL-BIN-240-IL Envirospill il Spill Bin 240l AFGCK SPL-BIN-120-MAINT Envirospill Maintenance Spill Bin 120l N SPL-BIN-240-MAINT Envirospill Maintenance Spill Bin 240l N 14kg MAX SIZE il/fuel TYPE Code escription Container Size Fluids ILGAT14B il Gator Spill Granules 14kg Bag Bag 14kg AFGCK ILGAT2P il Gator Spill Granules 2kg Pail Pail 2kg AFGCK ILGAT5P il Gator Spill Granules 5kg Pail Pail 5kg AFGCK ILGAT14P il Gator Spill Granules 14kg Pail Pail 14kg AFGCK TYPE 167

167 Waste il, Spill Control, Tools & Sealants / Sealants Standard RATI Standard PTFE Tape PTFE tape for sealing joints & pipework with course threads Cost effective solution popular with engineers 12m rolls with white plastic cover Code escription Roll Colour Fluids SR7009 PTFE Tape 12m White AFGCI Approx. 9:1 RATI 3-5 Layers USAGE Nine-2-ne PTFE Tape Unstretched PTFE tape for sealing pipework with course threads Approx. 9:1 usage ratio compared to standard PTFE ue to less layers of tape being required it does not bunch & you can back off the fitting 15m rolls with purple plastic cover Code escription Roll Colour Fluids CTS921 Nine-2-ne eluxe PTFE 15m Purple AFGCIL Medium STRENGTH Emergency Repair Tape Emergency repair tape for leaking oil lines, hoses & water pipes Typical use 3-5 layers; bonds quicker the tighter it is stretched Takes seconds to bond & approx. 1-2 mins to permanently seal Works on dirty, oily & wet surfaces & is resistant against UV rays Code escription Temperature Colour Fluids SR7013 Emergency Repair Tape -65 C/260 C Black AFGCIL Heldite Joining Compound For sealing & securing bolted, flanged or screwed pipe/thread joints Water-proof, anti-corrosive & suitable for most fluids Available in 250ml tin c/w brush applicator or 7ml bottle Code escription Size Colour Temperature Fluids CTS1808 Heldite 250ml 250ml Tin Brown -40 C/350 C AFGCIL CTS1810 Heldite 7ml 7ml Bottle Brown -40 C/350 C AFGCIL IESEL IESEL IESEL IESEL IL IL IL IL P PETRL P PETRL P PETRL P PETRL K KERSENE K KERSENE K KERSENE K KERSENE W WATER W WATER W WATER W WATER C CHEMICAL C CHEMICAL C CHEMICAL 168

168 Sealants \ Waste il, Spill Control, Tools & Sealants IESEL Loxeal Pipe Sealant Medium strength thread sealant for dismantling with hand tools esigned for pipework that may be removed for maintenance Handling: 20-40mins, Functional cure: 1-3 hrs, Full cure: 5-10hrs Shock & vibration resistant & suitable for many fluids Code escription Strength Size Colour Temperature Approval Fluids CTS1906 Loxeal Easy to dismantle 250ml White -55 C/150 C Gas EN751-1 AFGCI IESEL Loctite 577 Pipe Sealant Medium strength sealant for dismantling with large hand tools often specified on EM equipment esigned for pipework that may be removed for maintenance Handling: 20-40mins, Functional cure: 1-3 hrs, Full cure: 4-6 hrs Shock & vibration resistant & will not creep, shrink or shred Medium STRENGTH Medium STRENGTH Code escription Strength Size Colour Temperature Approval Fluids CTS1917 Loctite ml Can be dismantled 50ml Cream -55 C/150 C WRAS/Gas EN751-1 AFGCI CTS1920 Loctite ml Can be dismantled 250ml Cream -55 C/150 C WRAS/Gas EN751-1 AFGCI IESEL Loctite 638 Pipe Sealant High strength thread sealant for robust, demanding joining applications esigned for pipework that will never be dismantled & bond gaps up to 0.25mm Handling 10-30mins, Functional cure: 1-4 hrs, Full cure: 5-8 hrs High STRENGTH Code escription Strength Size Colour Temperature Approval Fluids CTS1922 Loctite ml Not for dismantling 250ml Green -55 C/180 C WRAS/Gas EN751-1 AFGCI IESEL IL IL IL IL P PETRL P PETRL P PETRL P PETRL K KERSENE K KERSENE K KERSENE K KERSENE Loctite 7649 Sealant Activator Solvent based sealant activating spray for speeding up curing For use with Loctite 577 & 638 sealants on pipework Apply thread sealant to the male end & activator to the female end Cure time: seconds W WATER W WATER W WATER W WATER 577 & 638 USE WITH Code escription Size Fluids CTS1921 Loctite 7649 Activator 150ml 150ml AFGCI 169

169 Waste il, Spill Control, Tools & Sealants / Sealants Medium STRENGTH High STRENGTH High STRENGTH Any USE BEFRE IESEL Loxeal Thread Locker Medium strength thread sealant for dismantling with hand tools esigned for locking nuts & bolts that may need to be removed Handling: 10-20mins, Functional cure: 1-3 hrs, Full cure: 3-6 hrs Cures effectively even when applied to oily surfaces IESEL Loxeal 43 Instant Adhesive General purpose glue for bonding surfaces together Works on even difficult to bond, porous or acidic materials e.g. leather, wood, tissue, metal, cardboard & rubber Cure time: 1-20 seconds ANY FLUI Bondseal Industrial Adhesive Adhesive to bond & seal all surfaces when drilling is not desirable Works on oily, wet & difficult surfaces e.g. wood, paper & metals Handling: 15-20mins, Full cure: 12 hrs Impact, shock, weather & chemical resistant Can be painted with water or solvent based paints IESEL IL IL IL P PETRL P PETRL P PETRL K KERSENE Code escription Strength Size Colour Temperature Approval Fluids CTS1914 Loxeal ml Can be dismantled 50ml Blue -55 C/200 C Gas EN751-1 AFGCI CTS1913 Loxeal g Sachet Can be dismantled 0.5g Blue -55 C/200 C Gas EN751-1 AFGCI Code escription Size Fluids CTS1915 Loxeal 43 Instant Adhesive 20g AFGCI Code escription Size Temperature Fluids CTS1918 Bondseal Industrial Adhesive 310ml Cartridge -40 C/100 C N K KERSENE K KERSENE W WATER W WATER W WATER Brake & Clutch Cleaner Code escription Size Fluids CTS1919 Brake and Clutch Cleaner 400ml AFGCI Aerosol cleaning spray that dissolves oil & grease from fittings For use on pipework components prior to thread sealant Ensure that joints are clean & oil free for the best possible bond 170

170 Tools \ Waste il, Spill Control, Tools & Sealants ANY FLUI Storage Tank Light Tank bulkhead light to illuminate the pumping equipment when operating outside daylight hours Compact design to easily fit inside the tank's front cabinent n/off switch for operating independently of pump equipment IP55 rated enclosure c/w ready to mount 2 hole metal bracket AC PWER AC PWER AC PWER Most Retail NZZLE TYPE Code escription V n/ff Switch Bulb (W) Core Cable Fluids ELEC1001 Tank Bulkhead Light 230 o 60 2m N ANY FLUI Pump Timer Box Electric timer box designed to control the running time of a pump Ensures that if left on, the pump will not run dry or against a dead-head for long periods of time Pre-set 5 minute run time as standard (can be adjusted to individual site requirements on request) IP55 rated enclosure with illuminated on/off switch Code escription V n/ff Switch Max. Switching Capability Fluids ELEC5023 Pump Timer Box 230 o 16A N ANY FLUI Electrical Contactor Box 230v electric contactor pump switch box Allows the Piusi MC Box to work with pumps that have a current of up to 10 amps IP55 rated enclosure Code escription V Max. Switching Capability Fluids ELEC25 Electrical Contactor Box A N ANY FLUI Husky Nozzle Service Kit Complete nozzle service kit for the clean removal & installation of nozzles, breakaways & filters Nozzle holder for keeping nozzles off the ground Safe-T-Break & filter cups for draining remaining fuel in each part All components fit inside the service pail for easy transportation Code escription Breakaway rain Cup Filter rain Cup Nozzle Holder Fluids HU-7262 Husky Nozzle Service Kit o o o N 171

171 Waste il, Spill Control, Tools & Sealants / Tools 5 litres MAX CAPACITY Flexi il Measure Jugs Measuring jugs for the easy transfer of oils Flexi spout c/w cap to prevent spillages Transparent polyethylene construction for easy checking of contents Available in 1ltr, 2ltr or 5ltr sizes Code escription Capacity (l)) Spout Cap/Lid Material Fluids il Measure Jug 1ltr 1 Flexi o Polyethylene F il Measure Jug 2ltr 2 Flexi o Polyethylene F il Measure Jug 5ltr 5 Flexi o Polyethylene F SPUT 220mm MAX SIZE Flexi IL IL il Funnels ften used alongside the jugs to further aid transfer Flexi spout c/w cap to prevent spillages Filter inside funnel to prevent any large debris contaminationfrom falling into oil Transparent polyethylene construction for easy checking of contents Available with 180mm or 220m diameter Code escription Size Spout Cap/Lid Material Fluids il Funnel 180mm 180mm Ø Flexi o Polyethylene F il Funnel 220mm 220mm Ø Flexi o Polyethylene F SPUT 86g SIZE See pages for water filters RELATE PRUCTS IESEL IL P PETRL K KERSENE Kolor Kut Water Finding Paste esigned to detect the presence of water in a fuel tank Apply to a clean piece of string or dipstick & lower into the bottom of the tank The brown paste will turn red when in contact with water, indicating its presence Instant detection for all fluids, although heavy oils may take a few seconds If water is found, it is recommended that you buy a water filter and get the tank inspected Code escription Size Colour Change Working Time Fluids SR7010 Kolor Kut Water Finding Paste 86g Brown to Red Instant AFGC 172

172 Tools \ Waste il, Spill Control, Tools & Sealants IESEL Kolor Kut Ullage Paste Ullage, or gauging paste, can be used to indicate the fuel level when no gauge exists Apply to a dipstick and lower into the bottom of the fuel tank The portion of the dipstick that comes into contact with the fuel will change colour Instant detection for all fluids, although heavy oils may take a few seconds It is particularly useful on underground tanks to indicate space remaining IESEL K KERSENE il Lifter esigned for domestic heating oil applications when a higher than normal lift is required Sucks up oil & stores in the 3.5l reservoir that feeds the boiler Internal suction solenoid pump ensure continuous oil supply to the heating system iagnostic flashing LE to alert of a warning situation Max lifting height & distance is based upon using 8m I tube If fitted inside a building, the drip tray c/w leak detector is required Questionnaire available for more complex installations 62g SIZE 8m MAX LIFT 100m MAX ISTANCE Code escription V Reservoir (l) Max Lift (m) Max istance (m) utlet Flow (lph) Inlet/utlet verflow utlet Fluids FC il Lifter m Lift 3/8 F BSP ½ F BSP AC FC A rip Tray c/w Leak etector AC ANY FLUI IL P PETRL Teddington Fire Valve Tester Safe & reliable unit to test whether a fire valve cuts off as it should Set the unit to the required temperature using the adjustable dial When the temperature is reached an amber light will come on to indicate that the unit is ready to use Insert the valve sensor into the test unit & allow 5minutes to see whether the valve trips Conforms to EN K KERSENE A must have safety item for oil heating engineers See pages for tank gauges RELATE PRUCTS Code escription Size Colour Change Working Time Fluids SR7014 Ullage Gauging Paste 62g Pink to Red Instant AFGC 14.5mm MAX SENSR SIZE See pages for fire valves RELATE PRUCTS Code escription V Max Sensor iameter Max Sensor Length Temperature Range Fluids MF6199 Teddington Fire Valve Tester mm 150mm C N 173

173 Waste il, Spill Control, Tools & Sealants / Tools 375mm LENGTH 46mm JAW WITH ANY FLUI Non-Sparking Wrench Non-sparking adjustable wrench safe for use whilst working in potentially flammable environments If dropped against another metal surface, such as a fuel storage tank, sparks will not be generated Constructed of Beryllium copper: GBEx II C Jaw width 46mm & length 375mm Fits around larger equipment such as hose tails that many standard wrenches do not Code escription Length (mm) Jaw Width (mm) Metal Weight (g) Fluids CTS2068 Non-Sparking Wrench Beryllium Copper Alloy 1410 N 6mm MAX SIZE Hex TYPE ANY FLUI WERA Ball Hex Allen Keys ouble ended high strength allen key designed for hexagon socket screws Short arm; standard allen key & long arm; ballpoint hexagon for awkward angles esign that prevents wear inside the socket screw by providing a larger contact area Chrome plated construction which prevents slipping 4mm, 5mm & 6mm versions available Code escription Size (mm) Long Arm (mm) Short Arm (mm) Type Fluids CTS2090 Ball Hex Allen Keys 4mm Hex N CTS2091 Ball Hex Allen Keys 5mm Hex N CTS2092 Ball Hex Allen Keys 6mm Hex N Adjustable SIZE 16 MAGNETS ANY FLUI Engineer Magnetic Wrist Band Woven nylon magnetic wrist band that secures small items such as screws, nuts & bolts Handy tool for engineers & workers that need to leave their hands free whilst working without losing any nuts & bolts Hook & loop closure that is adjustable to any wrist size Includes 4 pockets to hold power bits or small sockets Code escription Magnets Size Material Weight (g) Fluids CTS2093 Magnetic Wrist Band 16 Adjustable Nylon 140 N 174