PROFESSIONAL 270 o PIR MOTION DETECTOR
|
|
- Dustin Parsons
- 5 years ago
- Views:
Transcription
1 PROFESSIONAL 270 o PIR MOTION DETECTOR The unit can be installed only vertically (see the FIGURE 1A), not upside-down or horizontally (see the FIGURE 1B) as shown in the below drawing. FIGURE 1A 1. Motion Sensor 2. Back Plate 3. Corner Mounting Plate 4. Attachment Ring 5. Lens INTRODUCTION Your PROFESSIONAL 270 PIR MOTION DETECTOR is a fully automatic indoor and outdoor security/courtesy light controller capable of controlling up to 2000 watts of lighting. At night, the built-in passive infrared (PIR) motion sensor turns on the connected lighting system when it detects motion in its coverage area. During the day, the built-in photocell saves electricity by deactivating the lights. An adjustable timer lets you select how long the light stays on after activation. The unit is equipped with Thermal Compensation circuitry which helps ensure reliable sensor performance all year round. Masking strips are also included, enabling the user to blank off detection areas that are not required. The installation can be made on the wall or ceiling. With an exquisitely design corner mounting plate, users can also install the unit on external and internal corners. Note : Read this entire manual before you start to install the system. SAFETY PRECAUTIONS Do not install when it is raining. Be sure to switch off power source before installing. FIGURE 1B IMPORTANT Some local building codes may require installation of this product by a qualified electrician. Before proceeding with the installation, TURN OFF THE POWER TO THE LIGHTING CIRCUIT AT THE CIRCUIT BREAKER OR FUSE BOX TO AVOID ELECTRICAL SHOCK. IF IN ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN/TRADESPERSON. CHOOSING A MOUNTING LOCATION For the best results, fix your sensors on a solid surface, 1.8M~2.5M above the ground. For outdoor installation, a location under eaves is preferable. Avoid aiming the motion sensor at pools, heating vents, air conditioners or objects which may change temperature rapidly. Do not allow sunlight to fall directly on the front of unit. Try to avoid pointing the unit at trees or shrubs or where the motion of pets may be detected.
2 1 Prior to mounting, keep in mind that the motion sensor is most sensitive to the motion, which is across the detection field and less sensitive to the motion, which moves directly towards the detector. (FIGURE 2) 2 bottom. INSTALLATION FIGURE 2 The unit can apply to the following four installations. Select a location for the unit based on the coverage angles shown in FIGURE FIGURE 5 (2) Ceiling Mounting Installation - Preferable height 2.5M-4.0M (FIGURE 6) Drill two ceiling mount screw holes on preset position. Fix the back plate onto the ceiling with two screws from the bottom break-thru points. bottom. The Motion Sensor is mounted on the ceiling. FIGURE 3 To facilitate installation, it is essential to get a drill and a screwdriver ready. Install a wall switch adjacent to the power source (FIGURE 4). This helps you operate AUTO and SHUT OFF with ease. FIGURE 6 FIGURE 6 (1) Internal corner mounting (FIGURE 7) FIGURE 4 (1) Wall Mounting Installation (FIGURE 5) Install the back plate with two screws on desirable place on the wall. Select a location for internal corner mounting. Fix the corner mounting plate on to the wall with 2 screws. Fix the back plate to the corner mounting plate with two screws. bottom. The Motion Sensor can be firmly attached to the plate.
3 3 FIGURE 9A 4 (4) Force the cable through the seal and unscrew two screws on the cord grip. (5) Strip approximately 6-8mm insulating part of the wires from the power cord. (6) Before connection, ensure that the mounting box gasket is firmly seated in its original place. Note: The power cord must meet H05RN-F, 1.5mm² requirement. FIGURE 7 (2) External corner mounting (FIGURE 8) Select a location for external corner mounting. Fix the corner mounting plate on to the wall with 2 screws. Fix the back plate to the corner mounting plate with two screws. bottom. The Motion Sensor can be firmly attached to the plate. (7) Connect the BROWN wire (Live wire) of power cord to the terminal block "L" mark. Connect the BLUE wire (Neutral wire) of power cord to the terminal block N mark. Connect the BROWN wire of lamp wire to the terminal block "LS" mark. Connect the BLUE wire of lamp wire to the terminal block "N1" mark. Connect the GREEN/YELLOW wire of both power cord and lamp wire to the terminal block " " mark. (FIGURE 9B) FIGURE 8 FIGURE 8 WIRING INSTRUCTION (1) Switch off the power source or wall switch. (2) Remove the back plate (retained by 1 screws on (3) Make a small hole in the center of the cable gasket on the back plate. (FIGURE 9A) (FIGURE 9B) Note: 5 poles terminal block is equipped with earthing-mark hole, serving as a common point to connect the GREEN/YELLOW wire of both external Class I luminaries and exterior power source Class I luminaries refers to the product that requires earthing protection. SETTING THE LIGHTING SYSTEM Pulling off the attachment ring from the top lens segment by pressing two concave surfaces on the ring for time, lux and sensitivity adjustment. (FIGURE 10). After setting, fix the cover back to its place.
4 The LITE adjustment determines at what light level the 5 6 Light Control will start operating when you set the sensor to the AUTO MODE. Provisionally turn the LITE Control Knob fully clockwise to the moon (dusk) position. In this provisional setting mode, the Motion Sensor remains inactive during daylight. At dusk, slowly turn the LITE control counter-clockwise until the light turns on. At this setting the unit will become active at dusk each day. LUX LUX FIGURE 10 (1) TEST MODE Turn the Lite control and the Time control fully counter-clockwise -the TEST position. Turn the wall switch on, the lamp will turn on immediately and wait for 90 sec. Max. to warm up the unit. After warming-up time is expired and the lamp goes off, you may make a walk test and the lamp will turn on. This confirms that the wiring was done properly and that the lamp is working. Walk through the coverage area. The lamp will turn on when motion is detected and turn off shortly after motion stops. Wait about 5 seconds or more between test motions. FIGURE 12 SENS. ADJUSTMENT The motion sensor s sensitivity adjustment controls detection distance. It can be adjusted to compensate for seasonal variations in temperature and to reduce unwanted triggering. The optimum sensitivity can be achieved by setting the SENS. control knob initially to its mid position and then adjusting the control knob clockwise to increase (up to 12 meters) the detection distance or anti-clockwise to decrease (down to 3 meters) the detection distance. (FIGURE 13) (2) SETTINGS SENS SENS TIME ADJUSTMENT (FIGURE 11) The TIME adjustment controls how long the lamp will stay on after motion has been detected. Adjust the TIME Control Knob clockwise to increase (up to about 12 minutes) how long the light stays on or anti-clockwise to decrease (down to about 5 seconds) the time delay. 6 TIME FIGURE 11 LITE ADJUSTMENT (FIGURE 12) TIME FIGURE 13 Detection Range Setting/Adjustments Two kits of clip-on lens covers for limiting the detection range by blanking off lens segments is enclosed in the separate accessory bag. For different requirements, the clip-on lens covers can be cut to size horizontally and vertically to set detection coverage. (FIGURE 14) 1. Follow the grooves on the covers, and cut it to the suitable size to blank off the lens segment for the undesirable detection area. 2. Press the two concave surfaces on the attachment ring to pull off the ring. 3. Place the covers onto the notches at the sensor
5 lens top. The attachment ring is again fixed to the unit holding the covers steadily in place. 7 FIGURE 14 Note: Depending on individual need, the motion sensor can be adjusted up to 180 o horizontally.. (FIGURE 15) TROUBLESHOOTING Light does not turn on Confirm that you have made a correct wiring connection. Make sure that the bulbs have not burned out. Light remains on Make sure the wiring connection is correct. If you set the system to manual override, remember that you must turn the wall switch off for at least 10 seconds to switch the sensor to automatic operation and turn off the lights. Check if the TIME setting is correct. 8 Others The specification of protective shield shall consult to local service agent. OPERATION FIGURE 15 By using wall switch to your motion sensor, you can easily select one of two modes of operation: automatic operation and manual override. (1) AUTOMATIC OPERATION Turn on the wall switch. When the sensor detects motion, the floodlight automatically turns on. The built-in photocell turns the sensor off and on according to the light level selected by the LITE adjustment. (2) MANUAL OVERRIDE To keep the floodlight on regardless of the motion, you can override the automatic operation. Turn the wall switch off and on twice within 4 seconds. The interval between the first and second operation must be within seconds. In Manual Override mode, the floodlight will remain on. SPECIFICATIONS Power Requirement AC 220 ~ 240V / 50Hz Power Cord Requirement H05RN-F, 3G, 1.0mm² Max. 2,000W Incandescent Lighting Load Max. 480W Fluorescent Max. 300w LED (dimmable recommended) Detection Angle Up to 270 at 20 C, 2M Height Detection Distance Up to 12M at 20 C, 2M Height Swiveling Angle Horizontal 180 Recommended 1.8 ~ 2.5M Mounting Height (5.9 ~ 8.2 Ft) Wall Mount or 2.5 ~ 4.0M (8.2 ~ 13.1Ft) Ceiling Mount Wall Switch Control On / Off / Manual Override Sensor Operation Auto/Reset Time Adjustment 5 ± 3 sec ~12 ± 3 min Lux Adjustment Approx. 5 ~ 1000 Lux Sensitivity Adjustment Approx. 3~12M Operating Temperature -20 C ~ +40 C Warm Up Time About 90 Sec Protection Class Class II Protection Degree IP55 Safety CE, GS NG15 ODP In Manual Override mode, the light will remain on for around 4 hours despite no motion, then the light will turn off and the Light control will be back to Auto mode automatically. Users can also set the motion sensor back to Auto operation by turning off the wall switch for at least 10 seconds and then turn it back on.
PMWS2W SURFACE MOUNT 2-WIRE WALL SWITCH
infirm and children at night or when it is dark. Note: Read this entire manual before you start to install the system. SAFETY PRECAUTIONS PMWSW SURFACE MOUNT -WIRE WALL SWITCH Be sure to switch off power
More informationCompact Security FloodLight
MAL615 Instructs.qxd 1/9/05 12:18 PM Page 3 Compact Security FloodLight Installation and Operation Instructions MAL615 (Series 5) Introduction The Arlec MAL615 Movement Activated Sensor Light is a compact
More informationInstallation Manual GT500 GT500R RAB
Installation Manual GT500 GT500R RAB How Does Gotcha Work? Gotcha s infrared sensor sees small temperature changes caused by the motion of people or cars within its protection zone and turns on lights
More informationDedicated PIR Light Controller c/w RF remote control for LEDPRO Floodlights
Dedicated PIR Light Controller c/w RF remote control for LEDPRO Floodlights Model: LEDPRORFKB Black Model: LEDPRORFKWH White Model: LEDPROFOB RF Remote Fob Installation & Operating Instructions 1 1. General
More informationInstallation Instructions
LEDLUX TELLA SKU# 231091, 231093 Rated Voltage 220-240V~ 50Hz Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully
More informationInstallation Instructions
LEDLUX ECOFLOOD SKU# 231051, 231053, 231055 Rated Voltage 220-240V~ 50Hz Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions
More informationASSEMBLY & FITTING INSTRUCTIONS P-LUX3 LED TRI-SENSOR LANTERN
TRI-SENSOR TECHNOLOGY GL90LU ASSEMBLY & FITTING INSTRUCTIONS P-LUX LED TRI-SENSOR LANTERN Please read these instructions carefully before attempting to install this lantern. It is advisable to keep these
More informationMightylite Elite 16W LED Wall Light with PIR
Mightylite Elite LED Wall Light with PIR Installation & operating instructions HYLITE MIGHTYLITE ELITE WITH PIR INSTALLATION AND OPERATING INSTRUCTIONS The Hylite Mightylite Elite LED wall light is an
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS
ASSEMBLY AND INSTALLATION INSTRUCTIONS T0068 WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult
More informationLED AC DRIVERLESS FLOODLIGHTS WITH PIR FOR MODEL: FLAC10BPIR, FLAC20BPIR, FLAC30BPIR & FLAC50BPIR
INTRODUCTION The LED AC Driverless Floodlights with PIR include a hanging / mounting bracket and a 100cm cable. SPECIFICATION LED 800-4000lm IP65 180-240V IK07 6000K 50Hz >80 Ra 10W- 50W Dimensions: FLAC10BPIR:
More informationDUALBRITE Motion Sensing Coach Light
DUALBRITE Motion Sensing Coach Items Models 007677 SH-4144-AZ-B 063285 SH-4152-BK-A Questions or problems? Before returning to your retailer, refer to the troubleshooting guide in this manual or call our
More informationSecurity Lighting INSTRUCTION MANUAL 16W, 28W, 36W & 50W PIR Security LED Floodlight
Security ighting ISTRUCTI MAUA 16W, 28W, 36W & 50W Security ED Floodlight Installation & operating instructions HYITE MIGHTYITE SECURITY ED FOODIGHT - ISTAATI AD OPERATIG ISTRUCTIS The Mightylite floodlight
More informationECO CFL. with Photocell. Instructions. Model: ECO2DD Model: ECO3DD
ECO1DD WITHModel: PHOTOCELL Model: ECO2DD Model: ECO3DD ECO1DD.1 ECO2DD.1 Instructions ECO3DD.1 I nn S& TORp eurca tti ni O Installatio g N I n Ss t r u c t i o n s ECO CFL ECOFlood CFL Light with Photocell
More informationMOTION-ACTIVATED WALL LANTERN
SIZE: 8.5in X 11in Portfolio is a registered trademark of LF, LLC. All rights reserved. ITEM #0358718 MOTION-ACTIVATED WALL LANTERN MODEL #VEL-5069-MD-PIR Français p. 9 Español p. 17 ATTACH YOUR RECEIPT
More informationINSTALLATION INSTRUCTIONS GT8503E SECURITY FLOODLIGHT SOLAR POWERED
INSTALLATION INSTRUCTIONS GT8503E SECURITY FLOODLIGHT SOLAR POWERED CARTON CONTENTS QUANTITY DESCRIPTION 1 FLOODLIGHT W/ MOTION SENSOR & RECHARGABLE BATTERY 2 SOLAR PANEL W/ 15 FOOT POWER CORD 1 MOUNTING
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS
ASSEMBLY AND INSTALLATION INSTRUCTIONS 356-9231 / 356-9232 WARNING: NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Customer Service: 1-800-887-6326
More informationASSEMBLY & OPERATING INSTRUCTIONS
Model #: 44150-SL ASSEMBLY & OPERATING INSTRUCTIONS IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE USE ABOUT YOUR SOLAR SECURITY LIGHT During the day, the solar panel included with this MAXSA Solar
More informationInstallation Instructions
SOLAR GARDEN POWER CELL SKU#229120 Rated Voltage 12VDC Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before
More informationX20020 INFRESCO P 4kW Issue 4 User manual Date 16/02/16. Page 1 of 9 KEY FEATURES
X20020 INFRESCO P 4kW Issue 4 User manual Date 16/02/16 Page 1 of 9 KEY FEATURES Energy saving:- o Only provides heat when people are present. Extends lamp life. Temperature sensor:- o Lamps inhibited
More information3000W Dusk to Dawn Light Controller
3000W Dusk to Dawn Light Controller Model: NSLDD1000 White Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference
More informationSpecification Sheet for 2D LED Light
Specification Sheet for 2D LED Light Product Features LED light source, green and energy-saving; IP54 bulkhead, available to replace a 2D fitting; PC housing and opal diffuser; 3 Hours emergency; Microwave
More informationCompact 150 Watt Motion Sensing Halogen
TM Compact 150 Watt Motion Sensing Halogen Model: SH-9511AU Installation and Operating Instructions FEATURES Automatically comes on when motion is detected. Automatically turns light off. Photocell keeps
More informationUse and Care Guide. Part # SC SV-OS-BZ SC SV-OS-W Model #
Part # SC-20-840-SV-OS-BZ SC-20-840-SV-OS-W Model # 51402241 51402242 Use and Care Guide LED SECURITY LIGHT Dusk to Dawn Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m.,
More information18W Low Energy. instructions. Instructions
18W Low Energy Dusk-Dawn Bulkhead Cat No. ECO18B instructions Instructions A Reflector screw B Wall fixing screw x 2 cover fixing screw x 2 C Lamp Cable Clamp Grommet SECTION ONE GENERAL INFORMATION This
More informationInstallation Instructions
Please read all instructions before installing CD-250 Multi-way Dimming Wall Switch Vacancy Sensor Lens Air Gap Isolation Switch Lighted Switch ON/OFF/DIM button SPECIFICATIONS Voltage...120VAC, 60Hz Load
More informationMaxLite LED Medium Area Light
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More informationModel: ECO1FL Model: ECO2FL Model: ECO3FL. Installation & Operating Instructions ECO CFL Flood Light Uncontrolled
Model: ECO1FL Model: ECO2FL Model: ECO3FL Installation & Operating Instructions ECO CFL Flood Light Uncontrolled 2x 2x 20W 4 x 32mm 1 Ø6mm 60mm 35mm 6 x 30mm 2 Slaving For ECO CFL Flood Light Uncontrolled
More information120 LED DUAL HEAD SOLAR MOTION LIGHT
Version 1.2 120 LED DUAL HEAD SOLAR MOTION LIGHT Instruction Manual Item# 23401 Thank you very much for choosing a Nature Power Product! For future reference, please complete the owner record below: Model:
More informationInstallation Instructions
DT-300 360 Dual Technology Low Voltage Occupancy Sensor with Light Level, Isolated Relay and Manual On features Specifications Voltage...18-28VDC/VAC, half wave rectified AC Current Consumption...43mA
More informationMotion Sensing Coach Light
TM Motion Sensing Coach Light Model: SH-9291AU Installation and Operating Instructions FEATURES Automatically comes on when motion is detected. Automatically turns light off. Photocell keeps the light
More informationHigh quality die cast aluminium with glass diffuser
Product Catalogue 2018 Slim Floodlights High quality die cast aluminium with glass diffuser Incorporates high quality 4000k chip Integral driver Suppled pre-wired with bootlace ferrules Available in white
More informationSingle gang PIR switch Replaces a standard light switch or dimmer Turns off automatically Turns on automatically Security mode Switches all lighting,
Single gang PIR switch Replaces a standard light switch or dimmer Turns off automatically Turns on automatically Security mode Switches all lighting, heating and ventilation loads up to 10A installation
More informationC.fm Page 1 Thursday, February 21, :28 AM Raptor user manual
Raptor user manual 1 mounting bracket 2 swivel lock 3 clamp hole 4 lamp access screws 5 air vents 6 AC input & main fuse 7 cooling fan Thank you for selecting the Martin Raptor. This Martin lighting fixture
More informationDoc Ref: WD030/2/11/12 Fern-Howard Ltd. 2 Newman Lane, Alton, Hampshire, GU34 2QR. Reg. No
The Micro-Max is the smaller version of the Mini-Max, retaining the market leading features of the larger model. A prismatic diffuser gives an even light distribution from the energy efficient 2D lamp.
More informationTHE INTELLIGENT MOTION SENSOR TRACKING LIGHT
THE INTELLIGENT MOTION SENSOR TRACKING LIGHT INSTALLATION INSTRUCTIONS Read all instructions before proceeding with the installation OVERVIEW OF AEC-9336CU Lamp Cover Front housing Lamp 150W Antenna Video
More informationINSTALLATION & MAINTENANCE MANUAL HBL
INSTALLATI & MAINTENANCE MANUAL HBL series 230V 50Hz IP 65 122 1 GENERAL INSTRUCTIS These instructions should be read carefully and retained after installation by the end user for future reference and
More informationLOW-VOLTAGE TRANSFORMER INSTALLATION GUIDE. Models: VTR-100SL-SS, VTR-150SL-SS, & VTR-300SL-SS
LOW-VOLTAGE TRANSFORMER INSTALLATION GUIDE Models: VTR-100SL-SS, VTR-150SL-SS, & VTR-300SL-SS ATTENTION: Please read this installation guide carefully to ensure safe and efficient operation of this Power
More informationLIGHTING Autumn & Winter Offers 2018/2019
LIGHTING Autumn & Winter Offers 2018/2019 SEE OUR EXTENSIVE RANGE OF LAMPS AND FITTINGS OFFERS INSIDE Order Online at SupremeOffers.co.uk - 24hrs a Day, 7 Days a Week NEW FLOODLIGHTS & PIR FLOODLIGHTS
More informationIMPROVED LIGHTING CONTROLS
IMPROVED LIGHTING CONTROLS Lighting controls give you the flexibility to design a space for multiple use and easy access. They should be a part of the lighting plan for every room. Both manual and automatic
More informationD.fm Page 1 Wednesday, March 5, :21 PM Raptor user manual
Raptor user manual 1 mounting bracket 2 swivel lock 3 clamp hole 4 lamp access screws 5 air vents 2001-2002 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced,
More informationINSTALLATION GUIDES OUTDOOR LIVING
S OUTDOOR LIVING TABLE OF CONTENTS 12 Volt 12 Watt DC Transformer Page 2 12 Volt 50 Watt DC Smart Transformer Page 3 12 Volt 50 Watt Smart Transformer Control Page 4-5 Waterproof Dimmer For 12W Transformer
More informationCare & Usage Manual For Your Outdoor Lighting System
Care & Usage Manual For Your Outdoor Lighting System Table of Contents Section 1: Understanding Your Lighting... 4 With the purchase of your new outdoor lighting system, you will not only enhance the beauty,
More informationInstallation Instructions: Eco SpunBay LED High Bays
Installation Instructions: Eco SpunBay LED High Bays Installation Notes & Precautions: Read all precautions, warnings, instructions contained in this document. These instructions can be used to install
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
7.5 Swift Lock Ready Shape Tree (Patent Pending) Instructions IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: READ AND
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
5 Swift Lock Ready Shape Tree (Patent Pending) Instructions IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: READ AND FOLLOW
More informationSOLAR SECURITY LIGHT with MOTION SENSOR
SOLAR SECURITY LIGHT with MOTION SENSOR Instruction Manual Model: GS-10 Introduction Thank you for your purchase. GAMA SONIC solar charged lighting eliminates the problems associated with most solar lighting
More informationDoc Ref: WD029/2/11/12 Fern-Howard Ltd. 2 Newman Lane, Alton, Hampshire, GU34 2QR. Reg. No
Clean design lines give the Meridian range a leading edge for internal, easily maintained fittings. A straightforward design with a twist and lock diffuser means user-friendly maintenance and cost savings
More informationMotion and Light Sensor Kit LHBAS51
Motion and Light Sensor Kit LHBAS51 Installation Instructions For Linear Low and High Bay Fixtures PLEASE READ THESE INSTRUCTIONS BEFORE SAFETY INSTRUCTIONS AND WARNINGS WARNING: READ CAREFULLY BEFORE
More informationUser and Fitting Manual June 2008
User and Fitting Manual June 2008 Electric Curtain Track System Silent Gliss 5090 User and fitting Manual Silent Gliss 5090 Page Copyright June 2008 by Silent Gliss International Ltd., 3073 Gümligen/Berne
More informationHALOGEN FLOODLIGHTS Models CHL1260C & 1260T Part Nos: &
HALOGEN FLOODLIGHTS Models CHL1260C & 1260T Part Nos: 5460600 & 5460595 OPERATING & MAINTENANCE INSTRUCTIONS GC0610 INTRODUCTION Thank you for purchasing this CLARKE Halogen Floodlight. Before attempting
More informationSylvania 9 Color Changing One Plug Tree Tree ID # T5, Item # V
Sylvania 9 Color Changing One Plug Tree Tree ID # T5, Item # V66354-13 Thank you for purchasing this tree. This tree assembles in minutes and is decorated with 600 LED lights. This tree has 8 lighting
More information12V 160W Folding Portable Solar Panel Kit KDSLR160PNLA User Manual
12V 160W Folding Portable Solar Panel Kit KDSLR160PNLA User Manual Table of Contents Product Features... 1 Product Components... 2 Product Specifications... 2 LED Indicators... 3 Safety Precautions...
More informationInstalling and Setting Up Your Ring Floodlight Cam
Installing and Setting Up Your Ring Floodlight Cam This is so exciting You are about to set up the world s most advanced floodlight. Start by watching the installation videos in the Ring app. Next, read
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationInstallation and User Manual. with RAIN SENSOR.
with RAIN SENSOR www.solarsmartopener.com Revision..0 TABLE OF CONTENTS Features In The Box Further Items Required Basic Operation Solar Panel and Operator Installation Operator Installation Solar Panel
More informationIMPORTANT SAFEGUARDS READ THIS MANUAL AND FOLLOW ALL SAFETY INSTRUCTIONS THOROUGHLY BEFORE OPERATING THE EMIU INVERTER SYSTEM SAVE THESE INSTRUCTIONS
THIS UNIT CONTAINS A RECHARGEABLE VALVE-REGULATED LEAD ACID BATTERY. PLEASE RECYCLE OR DISPOSE OF PROPERLY. IMPORTANT SAFEGUARDS INTERRUPTIBLE EMERGENCY LIGHTING UNIT INVERTER INSTRUCTION MANUAL When using
More informationINSTRUCTIONS Solar Motion-Activated Wedge Light
INSTRUCTIONS Solar Motion-Activated Wedge Light MODELS #40234 #40235 #40236 IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE USE ABOUT YOUR SOLAR WEDGE LIGHT During the day, the solar cell charge panel
More informationOperating Instruction for Downlights
Operating Instruction for Downlights Type: ES_T4_1027_SILVER/ ES_T5_1027_WHITE/ ES_T6_1017_SILVER/ ES_T7_1017_WHITE/ ES_T8_1047_SILVER/ ES_T9_2019_WHITE/ ES_T10_1044_SILVER Index 1. General safety information...
More information28W WORK LAMP Model: CTL28 Part No:
28W WORK LAMP Model: CTL28 Part No: 4002905 INSTRUCTION MANUAL GC0609 INTRODUCTION Thank you for purchasing this CLARKE 28W Work Lamp. Before attempting to use the product, it is essential that you read
More informationThe following lighting types are NOT compatible with the TT- 402Wireless Inline Dimmers:
TT402 (300W) Incandescent Wireless receiver Inline Dimmer Product Description The TT- 402is a 40-300W dimmable wireless receiver. It can be paired with only circuits 1 and 2 (keys 4 or 5) on the Taptile
More informationInstallation Instructions
HN-300 Fixture Mount Nightlight Controller with LED Assembly SPECIFICATIONS Power... 120VAC, 60Hz Relay Type... Form A, N.O. Load Requirements @120VAC... 500W isolated relay rated 5A 250VAC Low Voltage
More informationALC-PRM-VFC. Ceiling Mounted Photocell. Product Guide. Overview. Features
Product Guide ALC-PRM-VFC Ceiling Mounted Photocell Overview The ALC-PRM-VFC photocell will turn lighting on when the ambient light falls below a preset level. The lighting will then be turned off when
More information1 Safety instructions. 2 Intended use. 3 Product characteristics. 4 Operation. LB management. Universal touch dimmer insert LED
Art. no.: 1711DE Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible. Please
More informationLED Area Light. This is the fixture of choice for all of our dealerships. Contact Us:
LED Area Light This is the fixture of choice for all of our dealerships. Contact Us: 7057 Marcelle St, Paramount, CA 90723 800-640-0386 www.altechefficiency.com sales@altechefficiency.com Specifications
More informationLED Twister II. User manual UK Version 1.0
LED Twister II User manual 152.624UK Version 1.0 LED DUOPLEX: For indoor use only CAUTION! Please read this manual carefully before operating! Pay special attention to Sections 3 & 5 of this document.
More information18W Round LED Slimline Emergency Light
18W Round LED Slimline Emergency Light Model: LEDMRQ18WHEM Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference
More information6 x 10 Belt Disc Sander
6 x 10 Belt Disc Sander FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CALL OUR CUSTOMER SERVICE HELP LINE : 01509 500400 THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE DESIGN OR SPECIFICATION TO THIS PRODUCT
More informationInstallation Instructions
Bi-Level Control Module For fixtures with CWA transformers and non-encased capacitors, using Metal Halide, Metal Halide (Pulse Start) or High Pressure Sodium lamps between 75-000W Model#s: -250H -400H
More informationSectional and Tilting Door Opener
Sectional and Tilting Door Opener Installation Instructions and User Guide 600 800 1000 S/N WARNING Please read the manual carefully before installation and use. The installation of your new door opener
More informationDemand Switch NEFA20 Plus. Installation Guide. Please read this entire guide before beginning the installation!
Demand Switch NEFA20 Plus Installation Guide Please read this entire guide before beginning the installation! Supplied Parts Protective Covers DIN Mounting Rail NEFA20 Plus Mounting Rail Spacer Warning
More informationMeasurements are expressed in millimeters.
T-Rex user manual Measurements are expressed in millimeters. 1 Lamp access 2 Focus adjustment 3 Mounting bracket 4 Swivel locks 5 Clamp hole 6 Air vent 190 285 7 AC input & main fuse 8 Microphone 490 164
More informationPIL0478 ISSUE 01/ 07/16
ISSUE 01/ 07/16 PIL0478 ZAFIR G9 CEILING FITTING PIL0478 ISSUE 01/ 07/16 PART C PART E PART 21 SELV 1 1.B 1 3.1 3.3 3.4 3.5 3.6, 3.8 3.10 3.12 3.14 3.16 3.17 3.18 3.19 3.19 ATTENTION! THE TABLE BELOW
More informationBATTERY BOOSTER/CHARGER MODEL NO: DIGICAR 600
BATTERY BOOSTER/CHARGER MODEL NO: DIGICAR 600 PART NO: 6261200 OPERATION & MAINTENANCE INSTRUCTIONS LS0815 INTRODUCTION Thank you for purchasing this CLARKE Battery booster / charger which is suitable
More information2x 10W LED Slimline Floodlight Twin Flood
2x 10W LED Slimline Floodlight Twin Flood Model: LED200FLBE Black Model: LED200FLWHE White Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and
More informationLED Area Light. scratch that. This is the fixture of choice for all of our dealerships. Contact Us:
LED Area Light scratch that. This is the fixture of choice for all of our dealerships. Contact Us: 7057 Marcelle St, Paramount, CA 90723 800-640-0386 www.altechelectronics.com sales@altechelectronics.com
More information18V CORDLESS COMBI DRILL MODEL NO: CON18NI
CON18NI.fm Page 1 Tuesday, August 21, 2012 11:53 AM 18V CORDLESS COMBI DRILL MODEL NO: CON18NI PART NO: 6485067 OPERATION & MAINTENANCE INSTRUCTIONS LS0812 CON18NI.fm Page 2 Tuesday, August 21, 2012 11:53
More informationInstruction Manual Model: GS-57B
Instruction Manual Model: GS-57B This product is covered under warranty for a 2 years period. In order to make sure that you will be covered, please activate your warranty by filling out all the information
More informationThanks for shopping with Improvements! Halcott Lighted Corner Christmas Tree 7 Item #546528
Thanks for shopping with Improvements! Halcott Lighted Corner Christmas Tree 7 Item #546528 IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY. PARTS LIST: 1 Tree Urn 1 Tree Section A 1 Tree Section
More informationRolling Thin Film Oven BM205. Impact Test Equipment Ltd & User Guide. User Guide
Rolling Thin Film Oven BM205 Impact Test Equipment Ltd & www.impact-test.com User Guide User Guide Impact Test Equipment Ltd. Building 21 Stevenston Ind. Est. Stevenston Ayrshire KA20 3LR T: 01294 602626
More informationHEAVY DUTY BATTERY BOOSTERS / CHARGER MODEL No. BC420N
HEAVY DUTY BATTERY BOOSTERS / CHARGER MODEL No. BC420N OPERATING & MAINTENANCE INSTRUCTIONS 1206 SPECIFICATIONS Supply Voltage 230 Max Charge (Amps) 60 (cont) Max Boost (Amps) 400 Boost/Charge (Volts)
More informationThe wide variety of systems for controlling and adjusting light brings great advantages:
The wide variety of systems for controlling and adjusting light brings great advantages: Flexibility, light can be adjusted to any place or to any activity. ooks, lighting can be chosen to suit the surroundings.
More information7.5 FT PRE-LIT ENGLEWOOD PINE TREE
ITEM #0243778 7.5 FT PRE-LIT ENGLEWOOD PINE TREE Holiday Living & Design is a registered trademark of LF, LLC. All Rights Reserved. MODEL #W14L030 Español p. 11 ATTACH YOUR RECEIPT HERE Serial Number Purchase
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationINSTALLATION MANUAL SPECTRUM BRAKE CONTROL
INSTALLATION MANUAL 51170 SPECTRUM BRAKE CONTROL TABLE OF CONTENTS Controls & Components Tools List Before You Begin Wiring Wiring Diagram Mounting the LED Display Rotary Knob Wiring the Plug Connector
More informationContractor. 2000W Halogen (4x500W Halogen) USING INSTRUCTIONS
Contractor 2000W Halogen (4x500W Halogen) - USING INSTRUCTIONS 1 Congratulations on your purchase of a POWERMOON balloon-lighting system. Your POWERMOON Contractor is the most up to date glare free floodlight
More informationRECHARGEABLE SPOTLIGHT
RECHARGEABLE SPOTLIGHT MODEL: RWL10 Part No: 4002822 INSTRUCTION MANUAL LS0609 INTRODUCTION Thank you for purchasing this CLARKE product Before attempting to use the product, it is essential that you read
More informationMania EF1 user manual
Mania EF1 user manual Measurements are expressed in millimeters. 290 142 312 Ø13 250 2003 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or
More informationUser manual. e-gate SLD-24V
User manual FOR e-gate SLD-24V 24V Sliding Gate Operators Contents how to use your automatic gate operator...... 1 how the controls work.................. 2 how to manually release the gate...........
More informationPole Mount COD Installations (PMCOD)
FLASHRIGHT Display Installation Instructions Pole Mount COD Installations (PMCOD) Delphi (Key needed in some cases) FlashRight Displays 3482 Keith Bridge Rd. Suite # 260 Cumming, GA 30041 Tel. 678-455-9121
More informationPOLARSTART PS-3025 SH Multi-Channel Remote Starter System for AUTOMATIC Transmissions
POLARSTART PS-3025 SH Multi-Channel Remote Starter System for AUTOMATIC Transmissions USER GUIDE INTRODUCTION...2 BASIC REMOTE OPERATION...2 REMOTE-STARTING YOUR VEHICLE...2 DRIVING OFF...2 IDLE MODE...2
More information18V CORDLESS DRILL MODEL NO: CON18LiC
18V CORDLESS DRILL MODEL NO: CON18LiC PART NO: 6479531 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC0817 - ISS 2 INTRODUCTION Thank you for purchasing this CLARKE Cordless Drill. Before
More informationOPERATING INSTRUCTIONS Solar Motion-Activated Wedge Light
MOTION-ACTIVATED WEDGE LIGHT OPERATING INSTRUCTIONS Solar Motion-Activated Wedge Light Model #40235." IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE USE ABOUT YOUR SOLAR WEDGE LIGHT During the day,
More informationI n s t a llat ion & O p e r atin g In s truc t ions
LED UNCONTROLLED FLOODLIGHT Model: LEDX20FLB Model: LEDX20FLWH Model: LEDX30FLB Model: LEDX30FLWH Model: LEDX10FLB Model: LEDX10FLWH I n s t a llat ion & O p e r atin g In s truc t ions 1. Designated Use
More informationINFRESCO 2KW VARIABLE CONTROLLER Issue 3
X20018 INFRESCO 2KW VARIABLE CONTROLLER Issue 3 infresco User Manual Date 19/08/14 Page 1 of 6 KEY FEATURES Soft Start up to 30% extended life of Lamp Variable Control Ability to find comfort level Simple
More informationINSTALLATION MANUAL. Outdoor Series RP-SAL-8W-50K-SF-GY-G1, RP-SAL-30W-50K-SF-GY-G1. south if in northern hemisphere for example). sunlight.
INSTALLATION MANUAL Outdoor Series RP-SAL-8W-50K-SF-GY-G1, RP-SAL-30W-50K-SF-GY-G1 Warning and Attention: 1. The average sunshine in the installation area should be above 3.5h/day in order to ensure full
More informationLEAD ACID BATTERY CHARGER
LEAD ACID BATTERY CHARGER MODEL NO: LA4 & LA6 OPERATION & MAINTENANCE INSTRUCTIONS LS1214 INTRODUCTION Thank you for purchasing this CLARKE Battery Charger. Please read this manual thoroughly, before attempting
More informationASSEMBLY INSTRUCTIONS PRODUCT CODE: CAUTION: Carefully Read Instructions and Procedures for Safe Operation. 7' Diamond Peak LED Tree
7' Diamond Peak LED Tree ASSEMBLY INSTRUCTIONS MODEL NO: U11G684A-024-01 (WL-019) PRODUCT CODE: 140-034067-090 CAUTION: Carefully Read Instructions and Procedures for Safe Operation. Receipt of Purchase:
More informationCordless two speed drill/driver K 10613
Cordless two speed drill/driver K 10613 SAFETY AND PRECAUTION 1 Consider work area environment. Do not expose tools to rain. Do not use tools in damp or wet locations Keep work area clean and well lit.
More informationSSX-300ST SolarMaxx 300 Illuminator
SSX-300ST SolarMaxx 300 Illuminator Service Manual 6018 Bowdendale Avenue Jacksonville, FL 32216 Customer Service: 904 731 5869 FAX 904 733 0012 Toll Free 800 684 6404 (English) TABLE OF CONTENTS Page
More informationChapter 4 Utility Systems Electrical
Chapter 4 Utility Systems Electrical Utility Systems Electrical The electrical supply to your home begins outside, where you will see either an overhead feed and piping down the side of your home or (if
More information