In summary, the procedures includes removal of the belly pans, draining of the engine block, draining of the radiator, coolant mixing and refilling.
|
|
- Colin Rice
- 5 years ago
- Views:
Transcription
1 COOLANT DRAIN AND CHANGE PROCEDURE Recently, there was a request for a picture guide for draining/changing coolant (Robot808 and James-man) and since I was going to do this operation on Idaho (88), I took a few pics to share for those that have not tried this procedure yet. I believe the procedure should be the same for all models except for the belly pan removal needed for the S4s. In summary, the procedures includes removal of the belly pans, draining of the engine block, draining of the radiator, coolant mixing and refilling. Tools/materials I used include: 8mm and 13mm socket, 3 inch socket extension, long handle ratchet wrench for the 13mm socket, torque wrench, large flat-blade screwdriver, 2 gallons anti-freeze, 2 gallons distilled water, small/medium kiddy wading pool, funnel for adding coolant, Porken's lift bars and jack stands. You will need a 10mm socket if you decide to remove the front belly pan. First, you will need to elevate the 928 so you can work comfortably and safely underneath it. I use Porken's lift bars and 4 sturdy jack stands. Weight off wheels is not critical so ramps could be used as well.
2 Next, if you have belly pans, the rear belly pan will need to be removed to get access to the engine drain bolts. The rear belly pan uses 8mm screws to attach the pan to the underside of the body. Remove the screws at the front of the rear pan (the ones that attach to the front belly pan). I used a 3" socket extension.
3 Remove the two screws on the sides of the belly pan (one on each side)
4 Finally, remove the rear screws while holding up the rear of the rear belly pan. When the last of the screws are out, you will need to slide the belly pan rearward to detach it from the front belly pan (part of the rear pan protrudes over the front pan so it won't drop straight down).
5 Once the rear pan is removed, you will be able to see the engine coolant drain bolts. These will require the 13mm socket to remove. At this point, you can decide whether to remove the front belly pan as well. In this procedure, I left the front pan in place - the procedure can be done with the front pan in place but it's a little tighter space to maneuver in. My preference is to remove both pans and I've included pictures of that procedure at the end of this post. The drain bolt is the one in the center of the picture below and has red paint on the seal. There are 2 drain bolts for the block. If you look in the same location on the other side of the block, you will see the other drain bolt. Both need to be drained.
6 Next, I positioned the drain pan and service covers in place.
7 I used a long handle ratchet to get extra leverage and more torque for removing the drain bolt. Make sure you keep the cap on the coolant reservoir tank - don't loosen or remove it yet.
8 You may find it a little tight to maneuver with the front belly pan installed and the kiddy pool in place but it is doable if you take your time and make sure your socket is securely on the drain bolt. You may try breaking the bolt loose first without the kiddy pool in place. Then position the pool while you remove the bolt.
9 When you get the bolt loosened, you should be able to remove it with your fingers. Coolant will begin to drain but at a fairly slow rate...
10 ...now you can go topside and loosen the cap on the coolant reservoir. This will allow the coolant to drain faster.
11 If you leave the front belly pan in place, it will leak coolant on it. No problem though, you can wipe it off afterward.
12 Here's a pic of the drain bolt. The WSM recommends using copper anti-seize on the threads before re-installing. The bolt also has a sealing ring. You can visually inspect the sealing ring for wear or damage. I have re-used the ring before but if you're not sure, you can order a replacement seal. I've purchased seals from 928 Intl but you can probably get them at any of the 928 parts suppliers.
13 When you have drained both sides of the block, you are ready to re-install the drain bolts. They should be torqued to 35 NM or 25.8 Ftlbs
14 Next, locate the radiator drain plug. It's located near the front of the car on the passenger side. If you have the front belly pan in place, you will see the access hole. The drain plug is made of plastic.
15 Use a long, large flat-blade screwdriver to remove the drain plug but position the kiddie pool under the plug before loosening it. When you remove the drain plug, you will notice is has a rubber seal ring incorporated. Check the condition of the seal and the threads of the plug and replace if damaged/worn.
16 After the coolant is all drained from the radiator, re-install the radiator drain plug using the long, large flat-blade screwdriver. The plug does not require much torque since the properly functioning seal prevents leaks and the threads are plastic - I simply snug it firmly. COOLANT MIX AND REFILL Now, you can mix the coolant. You can use your preference of coolant. I use the green coolant and plain ol distilled water.
17 I use to use 50/50 mixture of water/coolant but now days I'm using 70% water and 30% coolant. Once your coolant is mixed, you're ready to fill the reservoir.
18 I used service covers to protect the fenders and I place towels around the area I'll be pouring to keep splash from getting on engine and paint. Use a funnel. When pouring coolant in, I pour with one hand while holding the funnel with the other - raising the funnel just enough so I can see the level of coolant in the reservoir. At first, radiator and hoses will take in the coolant rather rapidly. When you get close to 2 gallons, it will slow down as air bleeds out of the engine block. When it slows down, I fill the reservoir to the top with coolant and wait for a while as it slowly fills the engine. During this time you can be productive by disposing of the old coolant, cleaning and putting away your tools or cleaning your belly pan.
19 Continue to fill slowly until the engine doesn't seem to take any more (i.e., several minutes pass and the reservoir level doesn't move). Check for leaks underneath the car. If no leaks, replace the reservoir cap and start the car and let it get up to operating temperature. You will want to monitor the temperature gauge and make sure it doesn't overheat. If there are still no leaks after reaching and maintaining operating temp, you can turn the car off and replace the rear belly pan. Then lower the car off the ramp or jack stands. Check the level of the coolant reservoir and ensure it is at the "full" level mark (about half full). Take the car for a test drive and check the reservoir level again afterward - wait for the car to cool and add coolant as needed. I continue to monitor the reservoir level after the next few drives and add coolant as necessary. CONGRATULATIONS! YOU'RE DONE! Now, for those that prefer to remove both belly pans for this job, here's a few pics of the screws/bolts to remove to get the front belly pan off. You will use an 8mm socket for all but two of the mounting hardware. There are two screws near the front and on the side of the belly pan (one on each side) that will require a long extension to reach. I used a 6" extension for these.
20 With the 6" extension still attached, remove the two 8mm screws that are just behind the vent scoop openings - there's one screw for each vent.
21 Next, remove the 8mm screws that are at the front of the belly pan. After removing the last screw, hold up the front of the belly pan with one hand...
22 ...and remove the last two 10mm bolts located near the middle of the belly pan.
23 Maneuver the front belly pan down and away from your work area. Piece of cake! Please feel free to comment or suggest improvements to this procedure as it will improve the quality of the post. THANKS for reading!
BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta).
BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). Based on the procedure published by Volkswagen, but modified for the "average" shadetree mechanic. Some special
More informationThermo-Bob 3 Installation Manual: KLR650E (2008 and newer)
Thermo-Bob 3 Installation Manual: KLR650E (2008 and newer) Thank you for purchasing the Thermo-Bob 3 radiator bypass system for the KLR650. Since the KLR already has a doohickey, it seemed that this thingamabob
More informationFord Racing BOSS 302 Engine Oil Cooler (11-14 GT)
Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets
More informationHonda Civic Oil Change
1988-1991 Honda Civic Oil Change Change the oil in your '88-'91 Honda Civic to improve engine performance and longevity. Written By: Phillip Takahashi ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION
More informationHow to change Mercedes W123 coolant
How to change Mercedes W123 coolant The coolant in your W123 only lasts so long. Don't let it go too long and risk excess corrosion and damage to sensitive climate control parts, like your heater servo
More informationMitsubishi Lancer Oil Change (2.0L I4 DOHC)
2002-2007 Mitsubishi Lancer Oil Change (2.0L I4 DOHC) Change the oil in your '02-'07 Mitsubishi Lancer, with 2.0L I4 DOHC engine, to improve engine performance and longevity. Written By: Phillip Takahashi
More informationTraditional method Oil Change Instructions For VW 1.9 TDI
Traditional method Oil Change Instructions For VW 1.9 TDI Created by DeafBug This document provides instructions on changing the oil and filter on a VW 1.9 TDI engines. All the pictures here are taken
More informationW C-230 Kompressor Sports Sedan 1.8l Thermostat Replacement & Antifreeze flush
W203 2003 C-230 Kompressor Sports Sedan 1.8l Thermostat Replacement & Antifreeze flush First, I have to thank everyone who has contributed to the MBworld.org forums without you; I would not have gotten
More informationVWvortex Forums > Golf IV & Jetta IV > DIY: Timing Belt And Coolant Pump Replacement on 2.0 AEG! Pics Inside! (Printable Version)
VWvortex Forums > Golf IV & Jetta IV > DIY: Timing Belt And Coolant Pump Replacement on 2.0 AEG! Pics Inside! (Printable Version) Click here to print this topic. Post Title: DIY: Timing Belt And Coolant
More informationMINI MANIA REMOTE OIL COOLER INSTALLATION INSTRUCTIONS P/N NME1055
MINI MANIA REMOTE OIL COOLER INSTALLATION INSTRUCTIONS P/N NME1055 Mini Mania s Cooper S Remote Oil Cooler Kit is designed to reduce operating temperatures by cooling the motor oil using an external radiator.
More informationMishimoto Performance Aluminum Mustang Radiator - Manual - (94-95 GT/Cobra/V6) - Installation Instructions
Mishimoto Performance Aluminum Mustang Radiator - Manual - (94-95 GT/Cobra/V6) - Installation Instructions The below installation instructions work for the following products: Mishimoto Performance Aluminum
More informationMustang Steeda Tri-Ax Shifter Installation Guide
Mustang Steeda Tri-Ax Shifter Installation Guide The below installation instructions work for the following products: Mustang Short-Throw Shifters and Mustang Handles This "all questions answered" guide
More informationHonda CRV Oil Change
1995-2001 Honda CRV Oil Change Change the oil in your '95-'01 Honda CRV to improve engine performance and longevity. Written By: Phillip Takahashi ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION
More informationDIY: Shiver Valve Check, Illustrated
DIY: Shiver Valve Check, Illustrated By Petemoss, AF1 Forum Tools needed: 4mm allen wrench to remove all the fairing pieces 2.5mm allen wrench to remove battery holder 5mm allen wrench for valve cover
More informationFerrari 355 Oil Change Procedure
Ferrari 355 Oil Change Procedure By: Dave Lelonek (Dave Rocks) on Ferrarichat.com July 21, 2014 Created based on model year 1998 (355 F1 GTS), other model years may apply. Disclaimer: This document was
More informationThermo-Bob Installation Manual: KLR650A ( )
Thermo-Bob Installation Manual: KLR650A (1987-2007) Thank you for purchasing the Thermo-Bob radiator bypass system for the KLR650. Since the KLR already has a doohickey, it seemed that this thingamabob
More informationList of parts needed below. Tools needed
1 BMW 645 Coolant leak repair (Cap with Seal Repair and Expanding Coolant Pipe Installation w Pics) By Michael R. Brown (Estimated time to complete the job is 6-8 hrs) List of parts needed below. BMW PART
More informationToyota 4Runner Oil Change (4.7L V8)
2003-2009 Toyota 4Runner Oil Change (4.7L V8) Change the oil in your 2003-2009 Toyota 4Runner, with 4.7L V8 engine, to improve engine performance and longevity. Written By: Ryan Bailey ifixit CC BY-NC-SA
More informationThere is hence three things you can do - add oil, adjust the temp that the clutch begins to engage, or do both.
As most of you may be aware, I have been doing a lot of research lately on our cooling system in the 80's including the fact that we have a dead spot on the OEM temp gauge which prompted me to not rely
More informationVolvo 850 Radiator Replacement Jason Reed 29 March 2013
This write up covers removing and replacing the radiator on a 97 855 GLT wagon with light pressure turbo and automatic transmission. This car has 162K miles. The radiator, which was original, developed
More informationHarley-Davidson Sportster Evolution Oil
Harley-Davidson Sportster Evolution Oil Change Changing the Engine (crankcase) oil and filter. Written By: Eric Essen ifixit CC BY-NC-SA www.ifixit.com Page 1 of 6 INTRODUCTION Although there have been
More information2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions
Page1 James Barone Racing Aftermarket Parts and Accessories 2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions Tools Required: Jack Lift or ramps Ratchet wrench Torque Wrench 6 and 12 Extension
More informationSteps 3 through 9 in this procedure describe making and using a cooling system bleed tool.
Cooling System Bleed Procedure Steps 3 through 9 in this procedure describe making and using a cooling system bleed tool. However, you can use a commercially available funnel-type coolant refill bleed
More informationLUBE-01, Oil Cooler General Information and Seal Replacement
Introduction LUBE-01, Oil Cooler General Information and Seal Replacement The first indication of failing oil cooler seals are normally a "milkshake" looking mixture in the coolant tank. This can also
More informationSpikes-Spider Hub Installation
Spikes-Spider Hub Installation The instructions that are provided with the Spikes Spiders are pretty good. I've created this page for two reasons: to show those that are thinking of buying a set exactly
More informationSR Performance Aluminum Radiator - Manual (96 4.6L)
SR Performance Aluminum Radiator - Manual (96 4.6L) Tools needed 1. Large and small pair of pliers 2. 8mm and 10mm deep socket and extensions 3. Spare Rags 4. Large Drain Pan 5. Funnel with small opening
More informationSW20 Coolant System Maintenance.
SW20 Coolant System Maintenance. This article contains information on how to change and bleed the coolant, as well as flushing the system. It is based on information in the service manual, tips gathered
More informationM52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit
Home BMW Solutions Porsche Solutions DIY Tech Engine Services Dyno Services Machining About Contact Store Tool Rental M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit This procedure
More information2010 Prius Maintenance
2010 Prius Maintenance Changing Oil Disclaimer: All the information stated in this document was provided by Prius owners. None were affiliated with Toyota Motor Corporation, except as customers. This document
More informationFULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L
2018-01-15 FORD F150 ECOBOOST 3.5L FULL BORE PERFORMANCE MANIFOLD SET (PART #500101X) 1 FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L INSTALLATION INSTRUCTIONS 2011-2012 FORD F150 3.5L ECOBOOST
More informationM-6642-MB Boss Oil Cooler INSTALLATION INSTRUCTIONS
!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! Caution: If you are not confident that you can complete the installation safely, have it completed by a certified technician!
More informationThermo-Bob 1 Installation Manual: Kawasaki Concours
Thermo-Bob 1 Installation Manual: 1986-2006 Kawasaki Concours This is a basic guide for installing the Thermo-Bob 1 on a Kawasaki ZG-1000 Concours. The bike used in the following photos was a 1995 year
More informationReplacing MK4 Golf/Jetta radiator mounts in-car
Replacing MK4 Golf/Jetta radiator mounts in-car This is a guide to replacing the radiator mounts in a MK4 Golf/Jetta. This involves moving the core support to the service position which allows you to do
More information14-6. TSB Revision ENGINE COOLING ON-VEHICLE SERVICE
14-6 RADIATOR CAP DRAIN PLUG ENGINE COOLING ON-VEHICLE SERVICE When removing the radiator cap, use care to avoid contact with hot coolant or steam Place a shop towel over the cap and turn the cap counterclockwise
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0925 APPLICATION 2011-12 E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler Congratulations for being selective enough
More informationDetroit Tuned R56 Oil Service How-To
Detroit Tuned R56 Oil Service How-To Welcome to Detroit Tuned s how-to guide for an oil service for an R56 MINI Cooper. It s always best to do an oil change on a hot engine as the hot oil will drain better
More informationMK5/MK6 Panzer Plate Install Instructions
MK5/MK6 Panzer Plate Install Instructions This is the install procedure for the dieselgeek.com MK5/MK6 Panzer Plate Skid Plate Kits. These instructions are for the following vehicles, regardless of engine
More informationSaab 9-3 Krona Downpipe Installation Instructions. What's Included:
www.kronaperformance.com 2003-2010 Saab 9-3 Krona Downpipe Installation Instructions What's Included: (1) 3 stainless downpipe (with or without catalyst) (1) 3-2.5 stainless downpipe adapter pipe (1) Turbo
More informationYOUR CAR's COOLANT MUST BE COLD TO DO THIS. DON'T BE STUPID AND SCALD YOURSELF.
I just read through the service manual, checked out Billman's recommendations, and tackled the coolant change on my 2003 s2000. I'm not a mechanic by trade but have done valve adjustments, head gaskets,
More informationC&R Racing Supercharger, Coolant & Power Steering Reservoir Set (07-10 GT500)
C&R Racing Supercharger, Coolant & Power Steering Reservoir Set (07-10 GT500) Required Tools: 3-4 ft. of Hose or Siphon Kit Drain Bucket/Pan Funnel Ratchet and 8mm Socket Open Ended 8mm Wrench Pliers Razor
More informationDrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationBHW Engine Coolant Temperature Replacement
BHW Engine Coolant Temperature Replacement NEVER perform this procedure on a hot engine. Parts: 059 919 501 A dual temperature sensor 032 121 142 retaining spring N 903 168 02 sensor round seal N 905 216
More informationThe following information shows the steps to change the rear brake pads and rotors on an E36 chassis.
1 of 20 1/18/2010 9:15 PM See More DIY Articles Bookmark Site! The following information shows the steps to change the rear brake pads and rotors on an E36 chassis. Disclaimer: The following information
More informationRear End Installation and Bearing Kit - 8.8in (86-12 V8; V6)
Rear End Installation and Bearing Kit - 8.8in (86-12 V8; 11-13 V6) Tools Required: Jack Stands 5 Floor Jack 2 Oil Pans 1 Wheel Blocks 2 Differential Oil 3 qts Friction Modifier 3 bottles Tube of Black
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0924 APPLICATION: 2011-12 E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler Congratulations for being selective enough
More informationZ1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 Aluminum
More informationFord Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours
Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Tools Required: Ratchet and socket set Torque wrench Large adjustable wrench Needle nose pliers A dozen
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS D Application: , E89 Z4 sdrive 35i without stock oil cooler* PARTS LIST
OIL COOLER KIT INSTALLATION INSTRUCTIONS D570-0891 Application: 2009-11, E89 Z4 sdrive 35i without stock oil cooler* PARTS LIST Qty Part No. Description 1 D573-0050 Oil Cooler + Frame Assy 1 D573-0044
More informationW123 Transmission Vacuum Modulator Adjustment DIY - measure it the 'right' way
W123 Transmission Vacuum Modulator Adjustment DIY - measure it the 'right' way Why do you need to do this?: You need to do this to properly check the internal hydraulic pressure of the transmission, either
More informationPrerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More informationSpecial Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationHow To: Thermostat change - D8 V6 194bhp
How To: Thermostat change - D8 V6 194bhp Firstly, take off the Air Filter hoses and connectors and lift off. This leaves you with this workable space... I started with taking the two bolts out of the cable
More informationENG-16, Turbocharger Replacement (Including Tips on K27 Turbocharger Installation)
ENG-16, Turbocharger Replacement (Including Tips on K27 Turbocharger Installation) Introduction Replacing the turbocharger on a 951 is not extremely difficult. However, it is very tedious because there
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0923 APPLICATION: 2011 E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler Congratulations for being selective enough to
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationEngine Oil, Cooling System
Engine Oil, Cooling System OIL FILTER 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): () 4.4 US qt (4.2 ) () 4.5 US qt (4.3 ) 7. Replace the engine oil fill
More informationExhaust Heat Shield Instructions NC 06-15
Exhaust Heat Shield Instructions NC 06-15 Thank you for purchasing the Track Dog Racing Exhaust Heat Shield for the 2006-2015 Mazda MX-5. Our TDR Heat Shield is designed to help maintain lower temperatures
More informationPML Installation Review p.k.y. 19 April 2014
Reason for installing a PML 11036 transmission pan on my 2010 GMC Savana 3500: 1. My 2010 GMC 3500, 12 foot box truck is placed under heavy hauling condition (construction tools and building material)
More informationSteeda Lightweight Tubular Radiator Support (05-09) - Installation Instructions
Steeda Lightweight Tubular Radiator Support (05-09) - Installation Instructions The below installation instructions work for the following products: Eibach Mustang Anti-Roll Kit (05-10) Please read through
More informationTwo bolts at. Two each side where studs pass through. rear. Two bolts at. front. Front-most bolt for diagonal brace. Rear jacking point
The following describes the process of changing the transmission s gear oil in my own 2008 CS 6sp. I have no relationship with any of the products mentioned, other than being a satisfied consumer. Exercise
More informationG503 WWII Jeep changing of the oil and oil filter
G503 WWII Jeep changing of the oil and oil filter It is not difficult to change the oil and oil filter for your G503 WWII jeep. It can be a little messy, but if your prepared, you can do this yourself
More information4 th Gen 4 Runner Front Bumper - Installation Instructions:
www.shrockworks.com info@shrockworks.com 877-474-7625 4 th Gen 4 Runner Front Bumper - Installation Instructions: Thank you for purchasing a ShrockWorks product. We are confident you will enjoy it for
More informationBBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt)
BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt) Install Time: Approx. 8-10 hrs Parts Needed: BBK Long Tube Headers Shorty mid pipe X/H O2 wiring harness extensions Hi-temp thread locker Tools Required:
More informationACURA NSX ABS/ALB Modulator Rebuild Procedure
Version 03 ACURA NSX ABS/ALB Modulator Rebuild Procedure I rebuilt my 1991 ABS/ALB modulator using this procedure. Please note that this will not guarantee that your ABS/ALB system issues will be resolved
More informationHow to Replace the B2 Piston Bore Seal
Page 1 Home Cars for sale Trucks for sale Where we are Links to other diesel sites About us Why diesel? Diesel Videos How they work How they sound FAQ Dodge Diesel Maintenance tips, parts and DIY DVD's
More informationZ1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide
Z1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide Congratulations on your new upgraded piping and intercooler kit, this kit has proven to provide the lowest intake air temps to date on our
More informationJames Barone Racing Focus ST Transmission Mount Installation Instructions
Page1 James Barone Racing 2013+ Focus ST Transmission Mount Installation Instructions What you will need: Jack and jack stands. (Jack stands are preferred) o Ramps will work but, the job will be much more
More informationExhaust Heat Shield Instructions ND
Exhaust Heat Shield Instructions ND 2016 + Thank you for purchasing the Track Dog Racing Exhaust Heat Shield for the 2016 to Present Mazda MX-5. Our TDR Heat Shield is designed to help maintain lower temperatures
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationTools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.
Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission
More informationWRX/STI Engine Oil Cooler
2002-14 WRX/STI Engine Oil Cooler 2014-04-21 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
More informationHere's the difference (externally) in the and 04+ bumper and headlights: (00-03 on top, 04 on bottom)
OK guys, I've been meaning to post this for awhile.. well here it goes. I did the '04 front end conversion on my '01 about 4-5 months ago, but then the dealer had to buy the car back for legal reasons.
More informationThe following information is gathered from pages of the Honda Aero Shop Manual.
Original write-up by W. Boyter The following information is gathered from pages 3.10-3.12 of the Honda Aero Shop Manual. First of all, pull all your spark plugs, make sure your transmission is in neutral.
More information7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions
7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following
More informationIMPORTANT INSTALLATION NOTE
IMPORTANT INSTALL NOTE IMPORTANT INSTALLATION NOTE IMPORTANT INSTALL NOTE MISHIMOTO-SUPPLIED HARDWARE (8) PC M6 X 1.0 X 16MM FLANGE HEAD BOLT NOTE: DO NOT USE IMPACT GUN TO INSTALL SUPPLIED M6 HARDWARE
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0907 APPLICATION: 2011-12 E90 335i/xi (N55 engine) with BMW M-Technic bumper and without stock oil cooler Congratulations for being selective enough
More informationPitch Stop Mount Support for WRX/STI
Pitch Stop Mount Support for 2015+ WRX/STI 2017-02-06 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
More informationSome tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000
Some tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000 Last change 2013-Oct-11 I bought Haynes manual for a starter. That s something well worth it s cost I believe.
More informationTCI Trans-Scat
Page 1 of 5 Return to Instruction Sheet index TCI 350000 Trans-Scat Installation Instructions For TURBO HYDRAMATIC 350 This kit will allow you to reprogram your transmission to meet your driving needs
More informationJ&M Stainless Steel Teflon Brake Lines - Front (94-98 Cobra)
J&M Stainless Steel Teflon Brake Lines - Front (94-98 Cobra) Time Required: 30min-1 hour. Tools and Supplies Required: Jack Jack Stands Lug Wrench or 13/16 Socket 10mm Socket Socket Wrench Torque Wrench
More informationInstallation Procedure Nissan Maxima SE 3L DOHC VE30DE
Phenolic Performance Intake Spacers Installation Procedure 1992-1994 Nissan Maxima SE 3L DOHC VE30DE Disclaimer: These spacers should only be installed by a qualified mechanic. If you decide to do the
More informationThermo-Bob 3 Installation on a 2015-and-newer Versys 650
Thermo-Bob 3 Installation on a 2015-and-newer Versys 650 Thank you for purchasing the Thermo-Bob 3 radiator bypass system for the Kawasaki Versys 650. Proper installation is critical: if you are not familiar
More informationMercedes Diesel Valve Adjustment Procedure
1 of 30 5/30/2008 12:58 PM Home Cars for sale Trucks for sale Where we are Links to other diesel sites About us Why diesel? Diesel Videos How they work How they sound FAQ Dodge Diesel Maintenance tips,
More informationFLUSHING YOUR COOLING SYSTEM BY MIKE ALLEN Published on: October 1, 1997
1 of 5 29/08/2006 12:28 PM SAVE THIS EMAIL THIS Close FLUSHING YOUR COOLING SYSTEM BY MIKE ALLEN Published on: October 1, 1997 You take off the cap and look at the coolant. It's a nice shade of green,
More informationGENERAL INSTRUCTIONS
KYMCO MXU 500i/700i Repair Manual Cooling System 6.Cooling System This chapter covers the location and servicing of the external components for the KYMCO MXU 700i and MXU 500i models. 1.Coolant... 6-4
More information2014+ FORD FIESTA ST DIRECT-FIT OIL COOLER KIT PARTS LIST AND INSTALLATION GUIDE CAUTION PARTS INCLUDED NOTE TOOLS NEEDED INSTALL PROCEDURE
PARTS LIST AND PARTS INCLUDED 3PC APPLICATION-SPECIFIC MOUNTING BRACKETS & SPACER 1PC 19-ROW OIL COOLER 1PC 4 ', X 1'' BRAIDED HOSE W/90-10AN FITTINGS 1PC 3'' X 2.5 '' BRAIDED HOSE W/45 AND 90-10AN FITTINGS
More informationMazda 3 & Mazdaspeed 3 Oil Cooler Installation Instructions
Page1 2007-2009 Mazda 3 & Mazdaspeed 3 Oil Cooler Installation Instructions Tooling: Jack and jack stands or a lift Socket wrench and torque wrench 10mm and 14mm sockets 3/16 Allen wrench 10mm wrench Pliers
More information2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
More informationWritten By: David Hodson
2008-Present Scion xb Oil Change Second generation Scion xb oil change. Written By: David Hodson ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION Change the oil in your 2008 or newer Scion xb
More informationAdjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003
SECTION ONE: Get Prepared - Tools Adjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003 Courtesy of: Half-Crazy Get a manual impact driver (the kind you hit
More informationRear Bumper Cover Unpainted ( ):
Rear Bumper Cover Unpainted (1999-2004): Tools Required: Ratchet Socket extension 7/16 deep well socket 7/16 wrench 5/16 socket Fastener Removal Tool Offset Phillips screwdriver Extendable magnet (optional
More informationFord Super Duty 5.4L Spark Plug Change F250 4x4 XLT Sport Crew Cab
1 of 32 Ford Super Duty 5.4L Spark Plug Change 2004 F250 4x4 XLT Sport Crew Cab Back to 2004 F250 Main Page Click Here for a PDF version of this article At close to 100k miles, I figured it was time for
More informationC3 Syncro Drive Proclimb 1100 Installation Instructions
Revision 4 Nov 8-2013 201A Old Town Road, Sicamous, BC. V0E 2V4 Ph 250-833 3538 Fax 888-716 5903 www.c3powersports.com Thank you for purchasing a ProClimb M, ProCross F & XF SyncroDrive Note: This modification
More informationM-Tuned reroute kit XX
M-Tuned reroute kit 14-161XX Manufactured and designed by: *Professional Installation Recommended but not required 1) Disconnect the negative terminal from the battery in the trunk. 2) Drain the coolant
More informationPorsche 928 with 16v LH-Jetronic Fuel System
Porsche 928 with 16v LH-Jetronic Fuel System Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger
More informationInstallation Instructions 6L80 Cast Aluminum. Deep Transmission Fluid
Installation Instructions 6L80 Cast Aluminum Deep Transmission Fluid Pan SPECIFICALLY DESIGNED FOR 2010-2014 CAMARO SS (V8) Part Number 70391 (see www.bmracing.com for the latest vehicle fitment applications
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D A. APPLICATION: E36/7 M-Roadster or M-Coupe 3.
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0323A APPLICATION: 1998-00 E36/7 M-Roadster or M-Coupe 3.2 Liter PARTS LIST Air Filter Assembly 3 1/2" Tube Intake Shield Silicone Hose Airflow
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Disc Brake Spindle Kit SUM-BKA2447 1964-72 A-BODY 1967-69 F-BODY 1968-74 X-BODY Thank you for choosing SUMMIT RACING for your braking needs. Please take the time to read and carefully
More informationAnglefire s Guide to Radiator Replacement
Land Rover Discovery 3 Anglefire s Guide to Radiator Replacement Mark Colston WWW.DISCO3CLUB.CO.UK August 2011 Version 1.0 Copyright Mark Colston Change Record. DATE Revision Update Notes Made By August
More information