Installation of Triple A-Pillar Pod and 7 Series Diesel Gauges Dodge Ram w/ 12 Valve Cummins Diesel Engine
|
|
- Giles Griffith
- 5 years ago
- Views:
Transcription
1 Installation of Triple A-Pillar Pod and 7 Series Diesel Gauges Dodge Ram w/ 12 Valve Cummins Diesel Engine GlowShift strives to provide outstanding technical support, and our technical support team is here to help you with any technical or installation questions that you may have regarding the installation of this gauge package. Each gauge and pod is rigorously tested to ensure that we are offering only the highest quality automotive products. Below you will find resources dedicated to helping you understand the installation process of GlowShift s triple A-pillar pod, and 60 PSI boost, exhaust gas temperature, and transmission temperature 7 Series gauges into a Dodge Ram with 12 Valve Cummins Diesel Engine. This gauge package was installed on a 1994 Dodge Ram with 12 Valve Cummins Diesel Engine. Installation of this gauge package on other model years may look a little different. Thread adapters may be required to complete certain portions of this installation. All of the necessary thread adapters required to complete this installation are available on GlowShiftDirect.com. For specific installation questions, please contact our technical support at GS.Gauge or us at TechSupport@GlowShiftGauges.com. TABLE OF CONTENTS Section One.. Boost Gauge Installation Section Two..Exhaust Temperature Probe Installation Section Three..Transmission Temperature Sensor Installation Section Four..Firewall Pass Through Section Five Removing Factory A-Pillar and Triple Pod Installation Section Six.. Gauge Installation Section Seven Testing Gauges for Functionality
2 Preparing for Installation Section One: Boost Gauge Installation Disconnect the cables from both batteries. 1. Locate and remove the boost pressure bolt that is located under the horn of the intake manifold. 2. The threads on this port are 1/8 NPT so you can easily screw the supplied barbed fitting into the port and tighten with a wrench. Be sure to use Teflon Tape on the threads in order to seal the port. 3. Connect the boost line to the barbed fitting. Run the boost hose to the firewall keeping it away from any direct heat source or moving parts. Make sure to go through a grommet at the firewall so the hose does not get damaged.
3 Section Two: Exhaust Temperature Probe Installation 1. Locate the exhaust manifold. Using a center punch mark and drill a hole on the backside of the exhaust manifold above the turbo mount. 2. Drill the exhaust manifold on the mark you made using a size R drill bit. Start by using a smaller drill bit and gradually step up to the size R. By doing this, it will reduce the amount of shavings that may enter the exhaust manifold. Warning: If you are installing the EGT probe before the turbo ensure that no metal shavings enter the turbo housing, as this can cause serious engine damage. 3. After drilling use an industrial vacuum to remove all the metal shavings out of the exhaust manifold. 4. Tap the hole you just drilled into the exhaust manifold to 1/8 NPT After tapping, use an industrial vacuum to remove all the shavings out of the exhaust manifold
4 6. Thread the feral fitting of the EGT probe into the exhaust manifold and tighten. Be sure not to over tighten this probe, a little past hand tight is a good rule of thumb. 7. Make sure to adjust the probe depth of the EGT probe so that it is in the middle of the exhaust manifold. 8. Run the steel braided cable of the EGT probe to the firewall making sure to keep it away from any direct heat source or moving parts.
5 Section Three: Transmission Temperature Sensor Installation 1. Locate the transmission test port bolt on the passenger side of the transmission. There are three bolts, be sure to remove the middle bolt. A transmission test port extender is necessary to complete the installation of this sensor, and can be purchased on GlowShiftDirect.com. 2. Take the supplied transmission temperature sensor and thread it into the transmission test port extender. Thread the transmission temperature sensor with test port extender attached into the test port. Be sure to use Teflon Tape on all threads. 3. Once the adapter and temperature sensor is installed into the transmission test port run the black lead wire on the sensor to the frame of the vehicle or any bare metal source. Make sure this wire is solidly grounded; if the gauge is not grounded properly it will read not read accurately. 4. Run 16 gauge automotive wire from the white lead on the transmission temperature sensor up to the firewall making sure to keep the wire away from any moving parts or direct heat source. It is a good idea to label the wire trans temp so you do not get it confused when connecting it to the gauge.
6 Section Four: Firewall Pass Through 1. Once you have the sensor and probe wires at the firewall you can pass them through an existing hole or new hole. Make sure there is a grommet in place so that you do not cut any of the wires. 2. After you have passed the sensor wires through the firewall you can route them through the dashboard and to your gauge mounting location. Section Five: Removing Factory A-Pillar and Triple Pod Installation 1. Remove your factory trim by carefully pulling until the spring tabs that hold it in place release. 2. Install your gauges into your GlowShift Triple Gauge Pod.
7 3. Connect the red, yellow, and black wires from each gauge. If you would like your gauges to dim with your headlights repeat this process with the orange wires as well. Keep the EGT and Transmission Temperature wires to the side, we will come back to them later. 4. Drill a small hole at the bottom of your factory trim. This hole will be used to route the gauge wires through the trim and to your power source. 5. Once the gauge wires are passed through the factory trim you can secure your GlowShift Triple Pod to your factory trim using the supplied screws. Predrilling the holes will make your install easier, but is not necessary. 6. Connect the boost line that was passed through your firewall to the back of your boost gauge.
8 Section Six: Gauge Installation 7. Re-install your factory trim with the pillar pod attached using the factory spring clips. 1. Reconnect the battery cables so you can test the fuse box using a multi-meter. 2. Remove the dashboard trim for your truck so that you can access your fuse panel. Using a multi-meter identify the switched 12 volt source that powers your headlights. When the headlights are on the multi-meter will read 12 volts, when they are off it will read 0 volts. This switched source will power the dimming feature of the gauge. 3. Again using the multi-meter, test and Identify both a constant and switched 12 volt source in the fuse box. Once they are identified install add-a-circuits into the appropriate spots.
9 4. Connect the yellow gauge wires to the constant 12v source wire coming from the add-a-circuit that you installed to your fuse box. 5. Connect the red gauge wires to the switched 12v source wire coming from the add-a-circuit that was installed to your fuse box. 6. Connect the black ground gauge wires to your dashboard assembly bracket or any other good ground source. 7. Connect the pink and blue wires from the EGT probe to the EGT gauge wire harness. 8. Connect the white transmission temperature sensor to the green wire on the transmission temperature gauge.
10 Section Seven: Testing Gauges for Functionality Start your engine to check the operation of the gauges to ensure they are functioning properly. Check under the vehicle to ensure there are no leaks. When the gauges power up the EGT and transmission temperature gauges will do a full sweep, the boost gauge will not since it is mechanically powered. Additional Installation Information & Material Requirements GlowShift Gauges Approved Conductor Wires: Successfully installing GlowShift Gauges may require lengths of wire (sizes and quantity depend on vehicle, gauge type, gauge location and / or sensor location). For correct and proper GlowShift Gauge installation and operation, the use of 18 Gauge (wire diameter) automotive grade conductor wire with sheathing is recommended for one or more gauges per vehicle. When installing and routing wires from the engine compartment, to inside the vehicle cabin, always employ the use of a rubber grommet. This will prevent and deter the stripping of power supply and / or sensor wires that is necessary to deliver vital statistics about your engine to your GlowShift engine monitoring instruments. Never use wire nuts to fasten or bound vehicle / gauge or sensor wiring. Always use securing crimp connectors or solder individual wire junctions together for optimum gauge installation and operation. GlowShift Gauges Approved Installation Accessories: GlowShift Gauges may require the installer or user to provide additional products, accessories or adapters for the correct installation and operation of a gauge or sensor, as per the GlowShift Installation Instructions. When installing and routing hoses to or from the engine compartment, to inside the vehicle cabin, always employ the use of a rubber grommet. This will prevent and deter the stretching or pinching of hoses that is necessary to deliver vital statistics about your engine to your GlowShift engine monitoring instruments. GlowShift Gauges Installation Instructions: Installation documents are solely to provide a guide for individuals that are mechanically and electronically able to install products. If you are unsure about the correct procedure of installation for a product or device, you should consult a professional mechanic or an Authorized GlowShift Installer. Limited Warranty and Disclaimer GlowShift Gauges, LLC. products come with a one year limited warranty on the internal parts of the product. This warranty starts from the date of purchase. GlowShift Gauges, LLC. will replace or repair any qualifying defective product received by the company before the end of the warranty period. Installation of this product must be performed by a licensed professional. Should the failure of the product be the result of damage occurring as a result of improper installation, alteration of the product or an act or omission on the part of the consumer, this warranty is void. GlowShift Gauges, LLC. shall not be responsible for any consequential damages which arise from the use and/or installation of the product. If the kit is installed in any manner other then specified, GlowShift Gauges, LLC. reserves the right to deny any warranty claims at the discretion of the technical support department. The one year warranty is not transferable and is valid for up to one year from the original date of purchase. Any product return must include the original packaging, a statement of the alleged defect and an RMA number must be provided. All RMA numbers are valid for 14 days from issued date. Upon receipt of the returned product, the company will test the product for defect. If the results of the testing do not support the warranty claim, do not reveal any defect or indicate consumer negligence in the installation and handling of the product, then the product will be returned to you and you will be charged a reshipping fee. If the product is returned from an address within the continental United States, within the first 14 days after purchase, and is found to be defective, GlowShift Gauges, LLC. will cover the cost of the return shipping with an ed return label. This offer is only valid for the continental US. All international shipping, customs fees and/or duty charges are solely the responsibility of the consumer. Additional Disclaimer Terms Improper installation of electricity-using products may cause damage to any vehicle or device to which the improperly handled or installed device is attached. Improperly installed product may cause electrical injury to persons. It is recommended that the device be installed by a licensed professional. GlowShift Gauges, LLC. assumes no liability for the installation of the product. Warranty or liability will not exceed the product purchase price which shall be the buyer s sole and exclusive remedy. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE WARRANTIES DESCRIBED ON THE FACE HEREOF INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. (GLOWSHIFT GAUGES, LLC. AT IT S DISCRETION, MAY PROVIDE REMEDY OF RETURN OF PURCHASE PRICE OR REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCT AS BUYERS SOLE AND EXCLUSIVE REMEDY.) GlowShift Gauges, LLC Cooper Road - Suite B-6 West Berlin, NJ Effective 6/2010
60 PSI Boost Gauge. For Product Numbers: MT-DV01_60, MT-WDV01_60
60 PSI Boost Gauge For Product Numbers: MT-DV01_60, MT-WDV01_60 Red: 12v Constant (un-switched) Source (+) Orange: 12v Dimmer (switched) Source (+) (optional) White: 12v Ignition (switched) Source (+)
More informationDODGE RAM 24V 5.9L CUMMINS
DODGE RAM 24V 5.9L CUMMINS DODGE RAM 24V 5.9L CUMMINS TABLE OF CONTENTS SECTION 1 Preparing the Installation 1 SECTION 2 Boost Gauge Installation 2 SECTION Pyrometer/EGT Gauge Installation 4 SECTION 4
More informationOPT7 LED AURA UNDERBODY KIT GENERAL INSTALLATION GUIDE
1 x LED Control Box 2 x 48 OPT7 LED Bars with Smart-Color LEDs 2 x 36 OPT7 LED Bars with Smart-Color LEDs 1 x E-Z Remote (Batteries Included) 1 x E-Z Keychain Remote (Batteries Included) 4 x 10ft LED Strip
More informationRace Sport Lighting RSUKIT LED UNDERBODY KIT INSTALLATION GUIDE
Race Sport Lighting RSUKIT LED UNDERBODY KIT INSTALLATION GUIDE PARTS LIST (INCLUDED IN THE KIT) 1 x LED Control Center Box 2 x 48 RGB Aluminum Channel LED Bars 2 x 36 RGB Aluminum Channel LED Bars 1 x
More information6 November Ford Powerstroke 6.0/7.3L X-Monitor 1 BD X-MONITOR Ford 6.0/7.3L Powerstroke
6 November 2006 1087200-7210 Ford Powerstroke 6.0/7.3L X-Monitor 1 BD X-MONITOR 1999-2007 Ford 6.0/7.3L Powerstroke I n s t a l l a t i o n M a n u a l Date Purchased Purchased from Installed by READ THIS
More informationDodge Ram 5.9L Cummins LOW FUEL PRESSURE ALARM LIGHT - Installation Manual -
29 September 2005 Dodge Cummins Low Fuel Pressure Alarm Light Kit 1081130-33 1 1999-2005 Dodge Ram 5.9L Cummins LOW FUEL PRESSURE ALARM LIGHT - Installation Manual - Part Number Sequence: 1081130 Red 1081133
More information½ DODGE CUMMINS OEM BYPASS LIFT PUMP KIT Installation Instructions Part #
29 July 2005 2003-04.5 Dodge Cummins OEM Bypass Lift Pump Kit # 1050227-1 - 2003-04½ DODGE CUMMINS OEM BYPASS LIFT PUMP KIT Installation Instructions Part # 1050227 PLEASE READ ALL INSTRUCTIONS CAREFULLY
More information31 January / Universal Dash-Top X-Monitor 1 BD X-MONITOR. Universal Top Button Dash-Mount Gauge System
31 January 2006 1080000 / 1080200 Universal Dash-Top X-Monitor 1 BD X-MONITOR Universal Top Button Dash-Mount Gauge System I n s t a l l a t i o n M a n u a l Part # Application 1080000 Universal Pyro
More informationDODGE CUMMINS 24V ISB OEM BYPASS LIFT PUMP KIT Installation Instructions Part #
2/15/2006 2000-2002 Dodge Cummins OEM Bypass Lift Pump Kit # 1050229-1 - 2000-02 DODGE CUMMINS 24V ISB OEM BYPASS LIFT PUMP KIT Installation Instructions Part # 1050229 PLEASE READ ALL INSTRUCTIONS CAREFULLY
More information12/05/2012 Lockup Co-Pilot Instructions INST. Installation Manual v1.6: Dodge 68RFE Automatic Transmission
Installation Manual v1.6: 2007.5-09 Dodge 68RFE Automatic Transmission Please read all instructions before the installation of the ATS Co-Pilot Thank you for purchasing the ATS Co-Pilot transmission management
More informationINSTALLATION INSTRUCTIONS MECHANICAL GAUGES
1062650-1966-77 MECHANICAL GAUGES QUESTIONS: If after completely reading these instructions you have questions regarding the operation or installation of your instrument(s), please contact Hardin Marine
More informationInstallation Manual v1.0: Dodge 68RFE Automatic Transmission. Please read all instructions before the installation of the ATS Co-Pilot
09/30/11 601-900-2356-INST Installation Manual v1.0: 2010-11 Dodge 68RFE Automatic Transmission Please read all instructions before the installation of the ATS Co-Pilot Thank you for purchasing the ATS
More informationDODGE CUMMINS MK-2 Micro-Kleen System
Installation Manual P/N MK20306 2003-07 DODGE CUMMINS MK-2 Micro-Kleen System Installation Instructions P/N MK20306 2 Micron Fuel Filter Installation PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number (also available as steering wheel mounted kit ES2593248) for VW
More informationBD SUPER B SPECIAL Dodge 5.9L Cummins 24v ISB
1 This turbo is intended for high performance applications and is not to be used for towing applications BD SUPER B SPECIAL 1994-2002 Dodge 5.9L Cummins 24v ISB Part# 1045120 PLEASE READ ALL INSTRUCTIONS
More information2010+ VW Mk6 2.0T Vent Boost Gauge Kit INSTALLATION GUIDE
INSTALLATION GUIDE 2010+ VW Mk6 2.0T Vent Boost Gauge Kit Congratulations on your purchase of the AWE Tuning Vent Boost Gauge Kit for the 2010+ VW Mk6 2.0T. Exquisite build quality with industry leading
More informationDodge Cummins 5.9L 24 Valve Edge Products EZ Module Installation Instructions & Manual
1998.5-2002 Dodge Cummins 5.9L 24 Valve Edge Products EZ Module Installation Instructions & Manual OLD P/N s: EZD1000 / EZD1000A / EZD1000B NEW P/N s: 30200 / 30201 2007 Edge Products All rights reserved.
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for (2005-2008) Proper service and repair procedures are vital
More informationAEROMOTIVE Part # L Mustang Digital FMU INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 17113 4.6L Mustang Digital FMU INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that
More information20250 Module Installation Guide
20250 Module Installation Guide 2013.5-2017 RAM 6.7L Cummins Up to 90HP Gain 1-3 MPG Fuel Savings AgDieselSolutions.com Adjustable switch connector Power +12 volts (Red wire) & Ground (Black wire) Injector
More informationAEROMOTIVE Part # INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 16303 INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this installation be carried
More informationINSTALLATION INSTRUCTIONS FOR PART #48003 WATER/METHANOL INJECTION SYSTEM 6.6L Duramax Diesel
Contents: INSTALLATION INSTRUCTIONS FOR PART #48003 WATER/METHANOL INJECTION SYSTEM 6.6L Duramax Diesel Parts List...3 Introduction...4 Installation Mechanical...4 Testing Pump and Mechanical System...8
More informationTransmission Guardian
Transmission Guardian Thank you for purchasing the Transmission Guardian from Bowler Performance Transmissions. We hope you are 100 percent satisfied with your purchase and if for any reason you are not,
More informationDfuser Stage I Power Module DT-466, DT-570, and HT-570
Dfuser Stage I Power Module DT-466, DT-570, and HT-570 Copyright 2004, 2005, 2006 dfuser.com, LLC. All rights reserved. Page 1 of 6 User Guide What Gain as much as +35HP and 90ft/lbs of torque!, plus improve
More informationUNLEASH THE POWER. See More at: bullydog.com WITH BULLY DOG PERFORMANCE PRODUCTS. Doc.# BD40009 v1.0.0
Bully Dog Technologies, LLC is a team built on integrity that is dedicated to leading the vehicle performance industry with an uncompromising code of ethics demonstrated in the soundness of its employees,
More informationFor electronically controlled E4OD and 4R100 automatic transmissions ** READ ALL INSTRUCTIONS BEFORE INSTALLATION **
26 August 2005 Ford PressureLoc #1060380 1 BD Ford PressureLoc Installation Manual For electronically controlled E4OD and 4R100 automatic transmissions Part#: 1060380 ** READ ALL INSTRUCTIONS BEFORE INSTALLATION
More informationROUSH FUEL SYSTEM UPGRADE CURRENT FORD MUSTANG 5.0L
ROUSH FUEL SYSTEM UPGRADE 2011- CURRENT FORD MUSTANG 5.0L P/N: 421602 (1313-FPVRKIT) Installation Instructions Before installing your ROUSH Performance Product(s), read through the entire installation
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number (also available as steering wheel mounted kit ES2593248) for VW
More informationTwin Turbo Installation Instructions
Twin Turbo Installation Instructions Pacific Performance Engineering 303 N Placentia Ave. Fullerton, CA 92831 www.ppediesel.com Legal in California only for racing vehicles which may never be used on the
More informationAttitude Instructions Ford 6.0 Powerstroke
Attitude Instructions Ford 6.0 Powerstroke Attitude 2003, Edge Products Incorporated All rights reserved. Edge Products Incorporated 5875 South Adams Avenue Suite 100 Ogden, UT 84405 (801) 476-3343 www.edgeproductsinc.com
More informationAEROMOTIVE Part # Subaru STI Fuel Rail Kit INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 14137 04-06 Subaru STI Fuel Rail Kit INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend
More informationDEMON CARBURETOR MANUAL CHOKE KIT #421441
DEMON CARBURETOR MANUAL CHOKE KIT #421441 CHOKE INSTALLATION INSTRUCTIONS LIT703 This manual choke kit is designed to be used on any Demon Carburetor with a choke tower. This covers the Road Demon Jr.
More informationInstallation Instructions
1 BD DODGE CUMMINS PERFORMANCE E X H A U S T M A N I F O L D Installation Instructions Application List 1994-1998 12V 1045980 1998½-2002 24V 1045985 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION KIT
More informationDfuser T/C Lock-Un Lock
Dfuser T/C Lock-Un Lock Performance Diesel and more! For more information visit our website at: http://www.dfuser.com Page 1 of 6 User Guide This harness overrides and monitors Torque Converter (T/C) lockup
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for Audi B6 A4 (2002-2004) Proper service and repair procedures
More informationAEROMOTIVE Part # Subaru Fuel Rails for Top Feed Injectors WRX & STI INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 14135 Subaru Fuel Rails for Top Feed Injectors 02-14 WRX & 07-14 STI INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems
More informationRapid Flow Induction Dodge Cummins 5.9L 52101
INSTALLATION Manual Rapid Flow Induction Vehicle Application Part Number 03-07 Dodge Cummins 5.9L 52101 TROUBLESHOOTING: If you have questions during the installation of this product, please visit www.bullydog.com/product_updates.php.
More informationBoost Sensor Kit Instructions. Table of Contents
V 1.5, 18 Jan, 2012 FW 1.01 Boost Sensor Kit Instructions Table of Contents 1. Introduction 2. Assembly 3. Installation 4. Set up 5. Launch 6. Operation 7. Fault Indications 1. Introduction. Thanks for
More informationDUAL WIDEBAND AIR/FUEL RATIO GAUGE Product Numbers: GS-W702W_Dual, GS-C702W_Dual, GS-T702W_Dual
Installation Instructions Tech Support: 856.768.8300 TechSupport@GlowShiftGauges.com DUAL WIDEBAND AIR/FUEL RATIO GAUGE Product Numbers: GS-W702W_Dual, GS-C702W_Dual, GS-T702W_Dual (1) Gauge (2) Controllers
More information2004½-2007 Dodge 5.9L Cummins 24v ISBe (600 motors only)
31 October 2006 Part # 1045235-1 - BD Supe r B Single 2004½-2007 Dodge 5.9L Cummins 24v ISBe (600 motors only) Part # 1045235 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. Note: This turbo system is
More informationBEFORE YOU BEGIN LIST OF COMPONENTS. Isopropyl SWITCH SCOTCH-BRITE PAD ALCOHOL PREP PAD SWITCH HARNESS REVOLVER PCM COVER STICKER
User Manual TABLE OF CONTENTS BEFORE YOU BEGIN...3 LIST OF COMPONENTS... 3 REVOLVER INSTALLATION 95-97 Trucks...4 REVOLVER INSTALLATION 98-03 Trucks...7 SWITCH INSTALLATION...12 SAFETY WARNING & CAUTION...14
More informationINSTALLATION INSTRUCTIONS FOR PART #49002 WATER/METHANOL INJECTION SYSTEM Dodge Cummins Diesel 5.9L
Contents: INSTALLATION INSTRUCTIONS FOR PART #49002 WATER/METHANOL INJECTION SYSTEM 94 06 Dodge Cummins Diesel 5.9L Parts List...3 Introduction...4 Installation Mechanical...4 Testing Pump and Mechanical
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2009-2018 Dodge Ram 1500 (Excl. Rebel Model) 2019 Dodge Ram 1500 Classic PART NUMBER: 32-1960, 32-1965, 32-1960L, 32-1965L
More informationHeavy Duty Air Command
2097 / 2227 Heavy Duty Air Command INSTALLATION INSTRUCTIONS Congratulations on your purchase of a new Air Command kit. This kit was designed to provide inflation control of your air helper springs. This
More informationDfuser T/C Lock Override with LED
Dfuser T/C Lock Override with LED the bug that has no cure For more information visit our website at: http://www.dfuser.com Page 1 of 7 User Guide This harness overrides and monitors Torque Converter (T/C)
More informationDodge 24v ISBe
BD SUPER B 2003-2004 Dodge 24v ISBe (Non 600 motors) Part # 1045230 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION This turbo system is not compatible with an AFE intake system WITHOUT MODIFICATIONS.
More informationEquipped with AEM DRYFLOW Filter No oil Required! Kit Part Number:
Equipped with AEM DRYFLOW Filter No oil Required! Kit Part Number: 2003-2006 Dodge Ram 5.9L Cummins Diesel CARB EO D-392-33 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced
More informationPart# Accessory Power Distribution Module
7 February 2006 Power Pod (1038800) Page 1 BD Powe r Pod Installation Instructions Part# 1038800 Accessory Power Distribution Module Power Pod Specifications: Eliminate multiple T-taps and splices on OEM
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9210 1994-2002 DODGE Ram 2500 Pickup L6-5.9L DSL C.A.R.B. E.O. # D-670 1994-2002 DODGE Ram 3500 Pickup L6-5.9L
More informationECS Tuning 3095 Cleveland-Massillon Rd. Norton, Ohio Phone Fax Web
B7 A4 Gauge Pod Installation Instructions Safety first:. When working with your vehicles electrical system; always disconnect the battery! Avoid shorting any circuits, or probing around wires. Failure
More informationDiesel Installation Instructions
Diesel Installation Instructions Note: please read instructions completely before installation to ensure a safe/easy installation. Installation is broken down in 3-parts. 1. Pump/Tank/Nozzle - (mechanical)
More informationINSTALLATION INSTRUCTIONS FOR PART #48003 WATER / METHANOL INJECTION SYSTEM CHEVY/GM DURAMAX 6.6L DIESEL. 2005, Snow Performance, Incorporated
INSTALLATION INSTRUCTIONS FOR PART #48003 WATER / METHANOL INJECTION SYSTEM CHEVY/GM DURAMAX 6.6L DIESEL orporated CONTENTS Kit Contents...3 Introduction...4 Nozzle Identification Chart:...4 Installation
More informationVehicle Application. Rapid Flow 4 Aluminized Exhaust Dodge Cummins 5.9L Rapid Flow 4 T-409 SST Exhaust Dodge Cummins 5.
INSTALLATION Manual Vehicle Application Part# Rapid Flow 4 Aluminized Exhaust Dodge Cummins 5.9L 94-02 182010 Rapid Flow 4 T-409 SST Exhaust Dodge Cummins 5.9L 94-02 182445 Troubleshooting/FAQ Warranty/Disccliamer
More informationInstallation Instructions. Application List Dodge 24V PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
1 BD DODGE CUMMINS 03-055 C O O L - I T I N T E R C O O L E R Installation Instructions Application List 2003-2006 Dodge 24V 1042510 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION KIT CONTENTS: Please
More informationReplace light bulb with the same number bulb as the one removed. White Wire: Connect to +12 Volt Lighting
INSTALLATION INSTRUCTIONS SHORT SWEEP ELECTRIC GAUGES 2650-1079-00 Rev. C CAUTION FOR ALL GAUGE INSTALLATION (AMMETERS EXCLUDED) As a safety precaution, the +12V wire attached to the positive I (+) terminal
More informationInstallation. Instructions ES416. VW MKIV Golf/Jetta/GLI 337/20AE. to activate integral fog lights in Jetta GLX, E-Code, and HID Lighting Systems
Installation Instructions to activate integral fog lights in Jetta GLX, E-Code, and HID Lighting Systems This tutorial is provided as a courtesy by ECS Tuning. VW MKIV Golf/Jetta/GLI 337/20AE best viewed
More informationDODGE CUMMINS Arctic-Heat Grid Relocation Kit
Installation Manual P/N 07509-350-GRK 2007.5-09 DODGE CUMMINS Arctic-Heat Grid Relocation Kit Installation Instructions P/N 07509-350-GRK GDP Arctic-Heat Grid Heater Installation PLEASE READ ALL INSTRUCTIONS
More information97-03 Volkswagen 1.9L TDI Injector Nozzles
97-03 Volkswagen 1.9L TDI Injector Nozzles Product Description Part Number.205 Injector Nozzels #44200.216 Injector Nozzels #44201 VW INJECTOR NOZZLES Introduction These instructions outline how to install
More informationvacuum/boost vent mounted ES best viewed in Acrobat Reader This tutorial is provided as a courtesy by ECS Tuning.
vent mounted vacuum/boost ES2713030 This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat Reader Proper service and repair procedures are vital to the safe, reliable operation of
More informationActuLink ABS Module - ABS-MOD-400
Installation Instructions ActuLink ABS Module - ABS-MOD-400 For more information on the installation and operation of Tuson s towable ABS system, consult the installation and operations manuals for the
More informationMega-Rail System Installation
Installation Manual Mega-Rail System P/N 030767-MRS 2003-2007 DODGE CUMMINS Mega-Rail System Installation Installation Instructions GDP 03-07 Mega-Rail System P/N 030767-MRS PLEASE READ ALL INSTRUCTIONS
More informationElectric Pilot System
Electric Pilot System Assembly, Operation & Maintenance Congratulations on your purchase, and thank you for selecting the Pro Pilot System from Blichmann Engineering. We are confident that it will provide
More informationSELECT -24 INSTALLATION GUIDE. INST036 Doc 2.02
SELECT -24 INSTALLATION GUIDE INST036 Doc 2.02 CONTENTS General Information...2 Select-24 Diagram...3 Mounting the Select Controller...4 Dual Pole Nosebox Installation...5 Aux Harness Installation...6
More informationReplace light bulb with the same number bulb as the one removed. White Wire: Connect to +12 Volt Lighting
INSTALLATION INSTRUCTIONS SHORT SWEEP ELECTRIC GAUGES 2650-1079-00 Rev. C CAUTION FOR ALL GAUGE INSTALLATION (AMMETERS EXCLUDED) As a safety precaution, the +12V wire attached to the positive I (+) terminal
More informationAEROMOTIVE Part # INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 16303 INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this installation be carried
More informationUNIVERSAL GAUGE WIRE HARNESS
2650-1797-00 UNIVERSAL GAUGE WIRE HARNESS For Installing Auto Meter Electric Speedometer, Tachometer, And Short Sweep Electric Oil Pressure, Water Temperature, Fuel Level, and Volt Meter Gauges. This harness
More informationwww. hydrofuse.com Installation Manual Fertilizer Machine V1.3
www. hydrofuse.com Installation Manual Fertilizer Machine V1.3 Introduction Hydrofuse is a new concept in fertilizing that works with existing irrigation (sprinkler) systems and automatically dispenses
More informationUSB Charge Port Installation Instructions
USB Charge Port Installation Instructions Lifetime Technical Support support@logolites.com 770-476-7322 www.logolites.com Manual 100-0014C Thank you for purchasing a Logo Lites USB Charge Port! USB Charge
More informationDodge Turbo Diesel Truck
2003-2009 Dodge Turbo Diesel Truck Gauge Wiring: The cigarette lighter power wires are a good source of ignition on power for gauges. You can use these also for the gauge lights, but the dimmer circuit
More informationAWE AirGate Carbon Intake Audi B9 S4/ S5 3.0T, and A4/A5/allroad 2.0T (coming soon). AWE website here
Thank you for your purchase of the AWE AirGate Carbon Intake for the 2016+ Audi B9 S4/ S5 3.0T, and A4/A5/allroad 2.0T (coming soon). For up-to-the-minute fitment information, be sure to visit the Audi
More informationCAPACITOR ACTUATED PORTABLE STARTER CAPS USER GUIDE. INST048 Doc 3.01
CAPACITOR ACTUATED PORTABLE STARTER CAPS USER GUIDE INST048 Doc 3.01 CONTENTS General Information...2 Charts...3 Before First Use...4 Safety Requirements...5 What to Expect from the CAPS...5 CAPS Diagram...6
More informationModel A Turn Signal Kit Installation Guide
Model A Turn Signal Kit Installation Guide Creative Connections, Inc. Consumer Hot Line: 888-471-LOGO 770-476-7322 In Atlanta, GA http://www.logolites.com P/N: 100-005/K 2008 Creative Connections, Inc.
More informationBD PRESSURELOC INSTALLATION MANUAL
May 03 BD PressureLoc #1030377 1 BD PRESSURELOC INSTALLATION MANUAL READ ALL INSTRUCTIONS BEFORE INSTALLATION May 03 BD PressureLoc #1030377 2 KIT COMPONENTS Switched 12V wiring harness Control Valve Attachments
More informationRACE PPE Manifolds and Up-Pipes
RACE ONLY High-Flow Exhaust Manifolds with Up-pipes GM DURAMAX 6.6L 2001-2015 DISCLAIMER OF LIABILITY This is a performance product which increases horsepower above factory specifications. Additional horsepower
More informationPowerMax Diesel Upgrade For Cummins Engines
PowerMax Diesel Upgrade For Cummins Engines 00.5-007.5 Dodge Ram With Cummins 5.9L Item 3 4 5 6 7 8 9 0 3 4 5 6 7 8 Parts List Description Turbocharger Ancillary kit 773069- (includes) Installation Instructions
More informationAWE Tuning W205 C300 SwitchPath Edition or Touring Edition cat back exhaust system.
Thank you for your purchase of the AWE Tuning 2015+ W205 C300 SwitchPath Edition or Touring Edition cat back exhaust system. For up to the minute fitment information, be sure to visit the W205 C300 section
More information2012 JK Vacuum Pump Relocator
0 JK Vacuum Pump Relocator Part #440300 Important Notes: Prior to beginning this or any installation read these instructions to familiarize yourself with the required steps and evaluate if you are experienced
More informationCummins-2004 Dodge Edge EZ Module Installation Instructions and Manual
Cummins-2004 Dodge Edge EZ Module Installation Instructions and Manual 2004, 2005 All rights reserved. 1080 South Depot Dr. Ogden, UT 84404 (801) 476-3343 www.edgeproducts.com Manual Version 110105 Table
More informationToggle Button Kit. Installation Instructions MK5 / MK6 Golf, MK5 Jetta
Toggle Button Kit Installation Instructions MK5 / MK6 Golf, MK5 Jetta Thank you for choosing the Double Apex Toggle Button kit. If you have any questions about the installation please do not hesitate to
More informationInstallation Instructions
Installation Instructions Automatic Retracting Running Board Vehicle Application Dodge Ram Quad Cab Pickup 2002-2005 Part Number: 75101-01 Dodge Ram Mega Cab Pickup 2006 - Current Part Number: 75118-01
More informationInstallation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)
Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well
More informationDual Fueler Kit Dodge Cummins 6.7L kit w/no pump ( ) package w/pump ( ) Installation Guide
Pacific Performance Engineering, Inc. www.ppediesel.com Dual Fueler Kit Dodge Cummins 6.7L 2007.5-2010 kit w/no pump (2130030) 2007.5-2010 package w/pump (2130031) Installation Guide Technical Support
More informationRecommended Supplies: Listed are tools that we found helpful, you may find other tools more beneficial, necessary for your specific application.
These instructions apply to the installation of all Western Diesel TurboGauges. Western Diesel TurboGauges are accurate and responsive, and when installed properly, will provide the diesel truck owner
More informationAudi Mk1 TT Vent Boost Gauge Kit
2000-05 Audi Mk1 TT Vent Boost Gauge Kit Congratulations on your purchase of the A.W.E. Tuning Center Vent Boost Gauge for your Audi TT. While the install is fairly straight forward, please review these
More informationForbidden Diesel Performance Ford 6.7L Powerstroke EGR Delete Instructions 6.7L EGR DELETE BY FORBIDDEN DIESEL PERFORMANCE. Page 1
6.7L EGR DELETE BY FORBIDDEN DIESEL PERFORMANCE Page 1 WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road
More informationL DODGE CUMMINS Maximizer System
Installation Manual P/N 07509MAX 2007.5-09 6.7L DODGE CUMMINS Maximizer System Installation Instructions P/N 07509MAX GDP Big Line Kit Installation PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION
More informationwith installation boost GAUGE this manual is for use with systems
owners manual with installation instructions dynafact boost GAUGE this manual is for use with systems 64050-64054 gale banks engineering 546 duggan avenue azusa, ca 91702 (626) 969-9600 www.bankspower.com
More informationAEROMOTIVE Part # Subaru STI Fuel Rails INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 14136 04-06 Subaru STI Fuel Rails INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend
More information1955 & 1956 CHEVROLET CAR INSTALLATION INSTRUCTIONS
650-587-00 Rev. B 955 & 956 CHEVROLET CAR Contents of Package # Component Picture Qty. #6 x 5/6, Screw Base Plate 5.3 #6, Lock washer Bezel 5.5 5.6 Light bulb and socket, blue Lower Steering Column Cover
More informationEquipped with AEM Dryflow Filter No Oil Required!
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9210 1994-2002 DODGE Ram 2500 Pickup L6-5.9L DSL C.A.R.B. E.O. # D-670 1994-2002 DODGE Ram 3500 Pickup L6-5.9L
More informationXtreme Air Command. Step 1 Prepare the components. Step 2 Select a mounting location. Parts list
2549 60 90 400 600 30 200 120 800 psi 1000 kpa PSI 0 150 Xtreme Air Command Installation instructions Congratulations on your purchase of a new Xtreme Air Command kit. This kit was designed to provide
More informationTurn Signal Kit Installation Instructions for Model A Fords & Other Antique Vehicles
Turn Signal Kit Installation Instructions for Model A Fords & Other Antique Vehicles Lifetime Technical Support support@logolites.com 770-476-7322 www.logolites.com Manual 100-0005N Thank you for purchasing
More informationadvanced FLOW engineering Instruction Manual P/N: Make: Nissan Model: Titan XD Year: Engine: V8-5.
advanced FLOW engineering Instruction Manual P/N: 46-20281 Make: Nissan Model: Titan XD Year: 2016-2017 Engine: V8-5.0L (td) Cummins Please read the entire instruction manual before proceeding. Ensure
More informationfor Audi B7/A4 ( ) Part Number ES8017 Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for (2005-2008) Proper service and repair procedures are vital
More informationIT IS IMPORTANT THAT YOU OBTAIN THE CORRECT INFORMATION FOR YOUR VEHICLE, OR DAMAGE TO THE WIRING SYSTEM COULD OCCUR.
Instructions for Universal Harness PRINT THESE INSTUCTIONS Gentex Mirror Installation Instructions Provided by www.rearviewautomirrors.com These instructions have been prepared to provide you with details
More informationKit Part Number:
Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8203 2003-2005 Dodge Ram 5.7L V8 CARB EO # D-392-28 2005 Dodge Powerwagon Hemi CARB EO # D-392-28 Brute Force Intake Systems that are
More informationMaxLite StaxMax LED Flood Lights
Operating Instructions MaxLite StaxMax LED Flood Lights Input Rating 120V-277V 50/60Hz (347/480v optional) Wet Location Rated IP65 Operating temperature -22⁰F to 105⁰F General Safety Information 1. READ
More informationFLUID DAMPER. Vehicle Applications:
INSTALLATION Manual Vehicle Applications: Vehicle description Product Part Number 94-98 5.9L Dodge Cummins 62100 98.5-02 5.9L Dodge Cummins 62101 03-06 5.9L Dodge Cummins 62102 01-06 6.6L GM Duramax 63100
More informationGDP STREET-GATE 38mm Wastegate System
Installation Manual STREET-GATE 38mm Wastegate System P/N SG67-38MM-7510 GDP STREET-GATE 38mm Wastegate System 07.5-10 DODGE CUMMINS Installation Instructions STREET-GATE 38mm Wastegate Kit p/n SG67-38MM-7510
More informationNEXUS. Introduction SENSOR MODULE &
2650-1056 INSTALLA AT TION INSTRUCTIONS NEXUS SENSOR MODULE & REMOTE ASSEMBLY IMPORTANT WEAR SAFETY GLASSES 60 80 40 100 FUEL 20 PSI 0 AUTO METER PRODUCTS INC. c 2004-6463 0 10 20 10 20 BOOST VAC In.Hg
More information