Fivalco. General Information

Transcription

1

2 General Information Fivalco is a US company in our 16 th year of manufacturing Fire Protection Valves of uncompromising quality for our discerning customers. All our products are FM or UL approved and most carry both UL and FM listings / approvals. The latest edition of the NFPA code stated products shall be listed or approved, without reference to either UL or FM although it is common practice for consultants to specify both a UL listing and a Factory Mutual approval. UL listed means that the product has been tested, has passed all the stringent tests mandated by UL and is listed in the UL catalogue of Fire Protection Equipment FM approved means that the product has passed all severe tests mandated by Factory Mutual and is approved by FM for use in building structures insured by Factory Mutual Insurance. We, and all other manufacturers of similar products are subject to identical factory and product audit approvals and tests without compromise as the same approval and test criteria are applied to all producers of such products. All butterfly and gate valves are pressure tested for approval at 4/5 times the working pressure depending on valve size, and all valves must pass a cycling test of 1000 open/shut operations without failure of any part or component. We take great care to make our products both attractive and functional and it is essential that our customers and end users do the same in order to maintain product integrity and proper function. We draw you attention to for minimum practices for handling and installation of our valves,at the end of this catalogue. We are not content with making valves purely to meet mandatory specifications and have added quality and other features to stand out above the crowd. All gate valves have Stainless Steel Stems for better corrosion resistance-our competitors use common brass. All gate valves are painted true Fire Engine Red-RAL 3000-no on site painting needed. All materials for Butterfly Valves are equal to or superior to our competitors The quality goes in before our name goes on All written material in this catalogue is copyrighted and may not be produced in part or in whole without express written permission. Violators will be prosecuted. Fivalco, Fireriser, Fireriser HP and Firefly are our registered Trade Marks. Use of the trade marks without written permission is illegal and all violators will be prosecuted to the full extent of the law.

3 Product Index Approved and Listed Valves FIRERISER GATE VALVES 4 GV-OSY-RW PSI CAST IRON RESILIENT OS&Y GATE VALVE GV-OSY-RW PSI DUCTILE IRON RESILIENT OS&Y GATE VALVE GV-OSY PSI DUCTILE IRON RESILIENT OS&Y GATE VALVE Flanged Ends GV PSI DUCTILE IRON RESILIENT OS&Y GATE VALVE Grooved Ends GV-NRS-RW PSI CAST IRON RESILIENT NRS GATE VALVE GV-NRS-F PSI DUCTILE IRON RESILIENT NRS GATE VALVE Flanged Ends GV-NRS-MJF PSI DUCTILE IRON RESILIENT NRS GATE VALVE Flanged by Mechanical Joint Ends GV-NRS-MJMJ PSI DUCTILE IRON RESILIENT NRS GATE VALVE Mechanical Joint Ends IP888 VERTICAL INDICATOR POST WP999 WALL INDICATOR POST INDICATOR POST ADJUSTMENT...11 CHECK VALVES F SWING CHECK VALVE 300 PSI DDCV-1161-U WAFER DOUBLE DOOR CHECK VALVE 175PSI FIRE CHECK DCG GROOVED END...14/15 Y-STRAINER 4 YS-G-1251 GROOVES ENS Y-STRAINER 175PSI YS-F 1161 FLANGED END Y-STRAINER 175PSI...17 FIRERISER BUTTERFLY VALVES 4 FIRERISER HPW WAFER BUTTERFLY VALVE 300PSI FIRERISER HPG GROOVED BUTTERFLY VALVE 300PSI FIRERISER HPG GROOVED/TAPPED BUTTERFLY VALVE 300PSI FIRERISER DW WAFER BUTTERFLY VALVE 175PSI FIREFLY DG BUTTERFLY VALVE 175PSI FIREFLY BG BRONZE BUTTERFLY VALVE 175PSI FIREFLY BT BRONZE BUTTERFLY VALVE 175PSI INSTALLATION GUIDE BUTTERFLY VALVE PACKING FIVALCO INC LIMITED WARRANTY...27 WE RESERVE THE RIGHT TO CHANGE MATERIALS AND SPECIFICATIONS WITHOUT NOTICE.

4

5 Fireriser Gate Valve Resilient Seated-200PSI-OS&Y Type Flanged End Fig. No.:GV-OSY WORKING PRESSURE 14 BARS/200PSI Materials List: Component Body Wedge Disc Stem Nut O-Ring Material Cast Iron: ASTM A126 Class B Cast Iron: ASTM A126 Class B EPDM Coated Bronze: ASTM B62 C83600 EPDM Stem Brass: ASTM B16 C3600 or SS: AISI 420 O-Ring(Cover) EPDM Bonnet Cast Iron: ASTM A126 Class B Packing Sq.Braided Non-Asbestos Packing Gland Cast Iron: ASTM A126 Class B Yoke Nut Bronze: ASTM B62 C83600 Washer PTFE Handwheel Ductile Iron: ASTM A Lock Nut Bronze: ASTM B62 C Dimensions ( mm/in): Valve Size 65/2-1/2 80/3 100/4 150/6 200/8 250/10 300/12 mm Inch mm Inch mm Inch mm Inch mm Inch mm Inch mm Inch A / / / B(Open) / / / / / / /64 B(Close) / / / / / / /64 C / / /2 D / / Notes: 1. Design and dimensions conform to AWWA C Flanged to ANSI B16.1, 125#. other flange types available. 3. Fusion bonded epoxy coated interior and exterior. 4. Valve is rated at 200PSI for Fire Protection Service. 5. Design and materials are subject to change without notice. 6. Specify Brass or SS stem when ordering. --

6 Fireriser Gate Valve Resilient Seated-250PSI-OS&Y Type Fig No.: GV-OSY Valve Standard: Conforms to AWWA C515 / BS5163 Working pressure: 17BARS/250PSI Fusion Bonded Epoxy Coated Interior and Exterior Flanged Ends: ANSI B16.1 Class125/250, EN PN10/PN16/ BS10 Table E Stainless Steel Stem Materials List: Component Material Body Ductile Iron : ASTM A Wedge Disc ASTM A EPDM Coated Stem Nut Bronze: ASTM B62 C83600 O-Ring EPDM Stem Brass: ASTM B16 C36000 or SS: AISI 420 O-Ring (Cover) EPDM Bonnet Ductile Iron: ASTM A Packing Sq. Braided Non-Asbestos Packing Gland Ductile Iron: ASTM A Yoke Nut Bronze: ASTM B62 C83600 Washer PTFE Handwheel Ductile Iron: ASTM A Lock Nut Bronze: ASTM B62 C Dimensions ( mm/in): Valve 65/2-1/2 80/3 100/4 150/6 200/8 250/10 300/12 Size mm Inch mm Inch mm Inch mm Inch mm Inch mm Inch mm Inch A / / / B (Open) / / / / / / /64 B (Close) / / / / / / /64 C / / /2 D / / Notes: 1. Design and dimensions conform to AWWA C Flanged to ANSI B16.1, 125#. Other flange types available. 3. Fusion bonded epoxy coated inside and out. 4. Valve is rated at 250 PSI for Fire Protection Service. 5. Design and materials are subject to chang without notice. 6. Specify Brass or SS stem when ordering. --

7 Fireriser Gate Valve Resilient Seated-300PSI-OS&Y Type-Flanged Ends Fig. No.: GV-OSY OR F Valve Standard: Conforms to AWWA C515 / BS5163 Working pressure: 21 Bars/300PSI. Fusion Bonded Epoxy Coated Interior and Exterior Flanged Ends: ANSI B16.1 Class125/250, EN PN10/PN16/ BS10 Table E Stainless Steel Stem Materials List: Component Material Body Ductile Iron : ASTM A Wedge Disc ASTM A EPDM Coated Stem Nut Bronze: ASTM B62 C83600 O-Ring EPDM Stem Brass: ASTM B16 C36000 or SS: AISI 420 O-Ring (Cover) EPDM Bonnet Ductile Iron: ASTM A Packing Sq. Braided Non-Asbestos Packing Gland Ductile Iron: ASTM A Yoke Nut Bronze: ASTM B62 C83600 Washer PTFE Handwheel Ductile Iron: ASTM A Lock Nut Bronze: ASTM B62 C Dimensions ( mm/inch): Valve 65/2-1/2 80/3 100/4 150/6 200/8 250/10 300/12 Size mm Inch mm Inch mm Inch mm Inch mm Inch mm Inch mm Inch A / / / B (Open) / / / / / / /64 B (Close) / / / / / / /64 C / / /2 D / / Notes: 1. Design and dimensions conform to AWWA C Flanged to ANSI B16.1, 125#. Other flange types available. 3. Fusion bonded epoxy coated inside and out. 4. Valve is rated at 300 PSI for Fire Protection Service. 5. Design and materials are subject to chang without notice. 6. Specify Brass or SS stem when ordering. --

8 Fireriser Gate Valve Resilient Seated-300PSI-OS&Y Type-Grooved Ends Fig. No.: G Valve Standard: Conforms to AWWA C515. Working pressure: 21Bars/ 300 psi. Fusion Bonded Epoxy Coated Interior and Exterior Grooved Ends: Metric or ANSI Pipe Sizes Stainless Steel Stem Materials List: Part Name Material ASTM Specification Handwheel Ductile Iron A Stem Nut Bronze B62 Packing Graphite Non-asbestos Gasket EPDM Commercial Bonnet Ductile Iron A Stem Stainless Steel AISI420 Wedge Nut Stainless Steel AISI304 Wedge Ductile Iron EPDM Coated Body Ductile Iron A Dimensions ( mm/inch): Size 65/ 2-1/2 80/3 100/4 125/5 150/6 200/8 250/10 300/12 mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch OD 73/ / / L / / / H / / / / / / / D / / /2 --

9 Fireriser Gate Valve Resilient Seated-200PSI-NRS Type-Flange Ends Fig. No.: GV-NRS WORKING PRESSURE 200PSI Dimensions ( mm/inch): Valve Size 65/ 2-1/2 80/3 100/4 150/6 200/8 250/10 300/12 mm Inch mm Inch mm Inch mm Inch mm Inch mm Inch mm Inch A / / / B / / / / / / /16 C D / / Materials List: Component Material Component Material Body Cast Iron: ASTM A126 Class B Gasket EPDM Wedge Disc ASTM A126 Class B EPDM Coated Bonnet Cast Iron: ASTM A126 Class B Stem Nut Bronze: ASTM B62 C83600 Thrust Washer PTFE O-Ring EPDM Post Plate Cast Iron: ASTM A126 Class B Stem Notes: Brass: ASTM B16 C36000 or SS, AISI Stainless steel stem. 2. Design and dimensions conform to AWWA C Flanged to ANSI B16.1, 125#. other flange types available. 4. Fusion bonded epoxy coated interior and exterior. 5. Valve is rated at 200PSI for Fire Protection Service. 6. Design and materials are subject to change without notice. 7. Specify Brass or SS stem when ordering. Operating nut Ductile Iron: ASTM A

10 Fireriser Gate Valve Resilient Seated-300PSI-NRS Type-Flanged Ends Fig. No.: F Valve Standard: Conforms to AWWA C515/BS Working pressure: 21 Bars / 300 Psi. Flanged Ends: EN PN10 / PN16, ANSI B16.1 Class125/250 Interior and Exterior Fusion Bonded Epoxy Coated RAL3000 Stainless Steel Stem Materials List: Part Name Material ASTM Specification NPT Plug Brass B16, C36000 Post Plate Ductile Iron A Wrench Nut Ductile Iron A Gland Ductile Iron A Thrust Collar Bronze ASTM B62 Bonnet Ductile Iron A Gasket EPDM Commercial Stem Stainless Steel AISI 420 Disc Nut Bronze ASTM B62 Wedge Disc Ductile Iron EPDM Coated Body Ductile Iron A Dimensions (mm/in): Size 100/4 125/5 150/6 200/8 250/10 300/12 mm inch mm inch mm inch mm inch mm inch mm inch H / / / D L / /

11 Fireriser Gate Valve Resilient Seated-300PSI-NRS Type-Flanged by MJ Ends Fig. No.: FXMJ Valve Standard: Conforms to AWWA C515. Working pressure: 21 Bars / 300 Psi. Flanged Ends: EN PN10 / PN16, ANSI B16.1 Class125 Mechanical-Joint dimensions: Conforms to ANSI / AWWA C153/ A21.53 Fusion Bonded Epoxy Coated Interior and Exterior RAL3000 Stainless Steel Stem Materials List: Part Name Material ASTM Specification NPT Plug Brass B16, C36000 Post Plate Ductile Iron A Wrench Nut Ductile Iron A Gland Ductile Iron A Thrust Collar Bronze ASTM B62 Bonnet Ductile Iron A Gasket EPDM Commercial Stem Stainless Steel AISI 420 Disc Nut Bronze ASTM B62 Wedge Disc Ductile Iron EPDM Coated Body Ductile Iron A Dimensions (mm/in): Size 100/4 150/6 200/8 250/10 300/12 mm inch mm inch mm inch mm inch mm inch L / / /2 H / / / D

12 Fireriser Gate Valve Resilient Seated-300PSI-NRS Type-Mechanical Joint Ends Fig. No.: MJ Valve Standard: Complies with AWWA C515. Stainless Steel Stem Working pressure: 21 Bars / 300 Psi. Mechanical-Joint dimensions: To ANSI / AWWA C153 / A21.53 Fusion Bonded Epoxy Coated Interior and Exterior RAL3000 Materials List: Part Name Material ASTM Specification NPT Plug Brass B16, C36000 Post Plate Ductile Iron A Wrench Nut Ductile Iron A Gland Ductile Iron A Thrust Collar Bronze ASTM B62 Bonnet Ductile Iron A Gasket EPDM Commercial Stem Stainless Steel AISI 420 Disc Nut Bronze ASTM B62 Wedge Disc Ductile Iron EPDM Coated Body Ductile Iron A Dimensions (mm/in): Size 100/4 150/6 200/8 250/10 300/12 mm inch mm inch mm inch mm inch mm inch L / / / /8 H / / / D

13 Fireriser Gate Valve Indicator Post Fig. No.: IP888 Materials List: DET QTY. Desciption Material 1 1 Locking Wrench Cast IroA126ClassB 2 1 Operating Nut Bronze B O-Ring Buna N 4 1 Top Section CastIronA126ClassB 5 1 Window Glass Commercial 6 2 Open Target Cast Aluminum 7 2 Shut Target Cast Aluminum 8 1 Target Carrier Nut Bronze B584 2 Target Carrier Plate 1/16" Sheet Metal 4 ClampTargetRetainer 302 S.S. 8 Pan Head Zinc Plated Steel 4 Hex Nut Zinc Plated Steel 9 1 1/2" NPT Pipe Plug Mall. Iron /8" Eyebolt Forged Steel 11 1 Hex Capscrew Zinc Plated Steel "Sq. Stem SS:AISI Crane Coupling CastIronA126ClassB 14 1 Cotter Pin Brass /4" Hex Hd. Screw Zinc Plated Steel 16 1 Telescoping Barrel CastIronA126ClassB 17 1 Lower Standpipe Pipe /4" Hex Hd. Screw Zinc Plated Steel 19 1 Base Flange CastIronA126ClassB /8" Hex Capscrew Zinc Plated Steel /8" Hex Nut Zinc Plated Steel Field Adjustment: 1. Remove the top section from the top of the Indicator Post assembly. 2. Cut the required length off the bottom of the Standpipe for the Ground Line to match up with Standpipe Ground Line mark. 3. Set the "OPEN" and "SHUT" targets for the appropriate valve size. 4. Reattach the Top Section to the top of the Indicator Post assembly. 5. Design and dimensions are subject to change without notice --

14 Fireriser Gate Valve Indicator Post Fig. No.:WP999 Materials List: No. Component ASTM Std. No. Component ASTM Std. 1 Eye Bolt ASTM A307B 12 Gasket PTFE 2 Hex Nut, 1/2-13UNC ASTM A307B 13 Hex Bolt M8 x15 ASTM A307B 3 Washer ASTM A570Gr Plug Malleable Iron 4 Hand Wheel ASTM A Target Cast Aluminum 5 Hex Bolt, 1/2-13UNC ASTM A307B 16 Hex Bolt M6x85 ASTM A307B 6 Hex Bolt, 1/2-13UNC ASTM A307B 17 Hex Nut M6 CS ASTM A307B 7 Snap Ring AISI Body ASTM A126 Class B 8 Cover ASTM A126 Class B 19 Stem AISI Operating Nut 10 Target Nut ASTM B62 C83600 or AISI 304 ASTM B62 C83600 or AISI Window Glass Plexiglass 20 Crane Coupling ASTM A Cotter Pin 1/4"x3" SS:AISI 304 Field Adjustment: 1. Remove the top section from the top of the Indicator Post assembly. 2. Set the "OPEN" and "SHUT" targets for the appropriate valves size. 3. Reattach the Top Section to the top of the Indicator Post assembly. 4. Design and materials are subject to change without notice. -10-

15 Fireriser Gate Valve Indicator Post Adjustment: Installation NOTE: Ensure that the Non-rising Stem Gate Valve is in the fully open position before installing the Ver-tical Indicator Post. 1.) Disassemble the Indicator Post Take off the Locking Wrench(11). slide odd the Top Section(20) together with the Operating Nut(19) and the square Stem(9) as well as the Crane Coupling(3)and ensure that all other accessories attached from the end of the Body(10) by loosening two Hex Cap screws(24) and Square Nut(23), slide off the Body(10) from the Standpipe(8) by loosening two Hex Cap Screws and Hex Nut, Loosen the two Hex Cap Screws and Hex Nut, Slide off the Standpipe(8) from the Base Flange(5). 2.) Install the Base Flange and Standpipe Attach the Base Flange(5) together with the Standpipe(8) to the Post Flange of the Non-rising Stem Gate Valve using the four Cap Screws(1) and Hex Nut(2). 3.) Adjust the Grade Line Mark Pull in and lower the Body(10) over the Standpipe(8) until the Ground Line Mark on the Body(10) is the same height as ground level. TIGHTEN THE Two Hex Cap Screws and Hex Nut. 4.) Adjust the Square Stem Lower the Stem(9) into Body (10) Standpipe(8) such that the Crane Coupling(13) fits over the Operating nut of the Non-rising Stem Gate Valve Ensure that the Stem(9) engages the Operating Nut(19) a minimum of 2 inches but no more than 4,5 inches, To check for correct engage-ment, the end of stem should be from 2 to 4,5 inches below the top of the Body(10). 5.) Adjust the Targets Remove the Target Carrier Assembly( ) from inside the Body(10) by rotating the Operating Nut(19) counterclockwise. The Open Target(16) and Shut Target(not shown) are adjusted up or down on the Target Carrier Assembly( ) by pull-ing the middle section of the Target(Open and Shut) a small distance away from the Target Carrier As-sembly( ) and sliding the Target(Open and Shut) up or down as desired. If the Non-Rising Stem Gate Valve is opened left: move the two Open Targets(16)to the very top of the Target Carrier Assembly( ). Locate the two Shut Targets(not shown)according to the Non-rising Stem Gate Valve size(stem)turning distance. If the Non-rising Stem Gate Valve is opened right: move the two Shut Targets(not shown) to the very top of the Target Carrier Assembly( ). Locate the two Open Targets(16) according to the Non-ris-ing Stem Gate Valve size(stem) turning distance. 6.) Final Assembly and Test Insert the Target Carrier Assembly( ) back into the Top Section (20) by rotating the Operating Nut(19) clockwise, Rotate until the Open Target(16) is centered in the window of the window of the Body(10) which corresponds with the Nut-rising Stem Gate Valve being in the open position. Lower the Top Sec-tion(20) with Target Carrier Assembly( ) onto the Body(10), assuring that the Stem(9) Engages with the Operating Nut(19) at least 2 inches but not more than 4.5inches. Secure the Top Sec-tion(20) to the Body(10) by tightening the Cap Screw(24) and Square Nut(23) Close the Non-rising Stem Gate Valve and make sure that the Shut Target(not shown) is properly centered in the window of the Body(10) and adjust as necessary. Maintenance Oil the bearing in the Top Section(20) at least once per year by adding several drops of oil in the hole located on the top of the Operating Nut(19). -11-

16 Fireriser Check Valve Resilient Seated 300PSI Flanged Ends Fig.No.: F Valve Standard: Conforms to AWWA C508, Clear Waterway Working Pressure: 21 Bars / 300 psi. Flanged Ends: EN PN10 / PN16/20. ANSI B16.1 Class125/250 Face to Face Dimensions: Conform to AWWA C508 Fusion Bonded Epoxy Coated Interior and Exterior RAL3000 Materials List: Part Name Material ASTM Specification Seat Ring Bronze B62 Plug Washer PTFE Commercial Hinge Pin SS304 AISI 304 Retainer Washer Bronze B62 Disc Ductile Iron A Clapper Arm Ductile Iron A Gasket EPDM Commercial Cover Ductile Iron A Body Ductile Iron A Dimensions (mm / in): Size 65/ 2-1/2 80/ 3 100/ 4 125/ 5 150/ 6 200/ 8 250/ /12 12 A mm inch / B mm

17 Fireriser Check Valve Double Door Check Valve Wafer Type Fig.No.:DDCV-1161-U-175PSI WORKING PRESSURE 175PSI/12.5BARS Materials List: Component Description Material 1 Body Cast lron ASTM Al26 Class B 2 Disc Stainless Steel AlSl Spring Stainless Steel AISl Hinge Pin Stainless SteeI AISl Stop Pin Stainless Steel AISl Spacer PTFE 7 Pin Retainer Stainless SteeI AISI Gasket PTFE 9 Washer PTFE 10 Lifting Hook Carbon SteeI(Not Shown,only for 8",10"&12") Dimensions (mm/in): Size A фb фd Size A фb фd Inch mm Inch mm Inch mm Inch mm Inch mm Inch mm Inch mm Inch mm 4" " " " " Notes: 1.Working Pressure 175PSl 2.Stainless steel disc for exceiient corrosion resistance. 3.Design and materials are subject to change without notice. -13-

18 Fireriser Check Valve Fig. No.:DCG Specifications Working Pressure : 300 PSI(21 Bars) Max Test Pressure : 500 PSI (34.5Bars) Max Working Temp : 250 F (120 ) Primary Materials: Component Body Color Clapper Clapper/ Facing Seat Ring Spring Hinge Pin Hinge Pin/ Bushings Material Ductile iron conforming to ASTMA 536 epoxy coated Red or black (optional) 2"-5" type 304or 302 stainless steel to ASTMA 167 6"-8" ductile iron conforming to ASTMA 536,grade Grade E EPDM/-40"to 230 F (-40"to 110 ) Service Temperature range Type 304 stainless steel to ASTMA-123 ASTMA-213, ASTMA-312 or ASTMA-269 Type 302 stainless steel to ASTMA-313 Type304 or 302 stainless steel to ASTMA-580 Sintered bronze to ASTMB438 Flow Data-Friction Los(Ft. Pipe) Valves Pipe C=100 C=200 Size OD Sch.10 Sch.30 Sch.40 Sch.10 Sch.30 Sch.40 In/mn In/mn Ft/m Ft/m In/mn In/mn Ft/m Ft/m /

19 Fireriser Check Valve Grooved Check Valves, UL, ULC Listed/FM Approved Grooved End, Size: 2-1/2", 3"4",6"and 8" Fig. No.:DCG WORKING PRESSURE 300PSI/21BARS The Check Valve is a compact, cost effective valve offering low pressure-drop, non-slam performance the Check valve assembly is lighter and fast to install, and costs less than flanged and wafer valve assemblies.in the fullyopen position the clapper is held tightly against the valve body, out of the flow stream, to provide maximum flow area and prevention of clapper flutter. The clapper design produces quick, non-slam closure before flow reversal can occur, while meeting FM requirements for an anti-water hammer valve rating. Each valve is hydrostatically tested for leak tightness to 500 PSI. The clapper-seat design permits leak free sealing of back pressures in service conditions ranging from 300 PSI to as low as 5 PSI. Flow Data-Friction Los(Ft. Pipe) Valves Pipe C=100 C=200 Size OD Sch.10 Sch.30 Sch.40 Sch.10 Sch.30 Sch.40 In/mn In/mn Ft/m Ft/m In/mn In/mn Ft/m Ft/m /

20 Fireriser "Y" Strainer Ductile Iron Y Steainer Grooved End-175PSI/12.5BARS Fig.No.:YS-G-1251 Pressure and Temperature: Nominal Pressure 175PSI Hydraulic Shell Test Pressure 350PSI Pressure / Temperature Ratings 175PSI from-10 ~ 120 Suitable Media Water, Oil, Gas Material Specification: Component Material Body Ductile lron ASTM A Cover Ductile lron ASTM A Screen Stainless Steel AISI 304 Gasket PTFE/Graphite Plug Ductile lron ASTM A Standard Screens: Nominal Size (mm) Hole Dia. (mm) Free Flow Area (%) Dimensions: Nominal Size Inch mm Notes: PipeOD mm A mm B mm E mm Blow Off BSP/NPT Weight kg 2-1/2 65A " /2 65B " " " " /2" " 150A " " 150B " " " " " " " Grooved joint-dimensions are made in accordance with metric and ANSI standard pipe sizes. 2.Pressure and temperature ratings are for grooved couplings of an equivalent pressure ratings. 3.Design and materials are subject to change without notice. -16-

21 Fireriser "Y" Strainer Flanged End-175PSI Fig.No.:YS-F-1161 Pressure and Temperature: Nominal Pressure 175PSI /12.5Bars Hydraulic Shell Test Pressure 350PSI Pressure / Temperature Ratings 175PSI from-10 ~ 120 Suitable Media Water, Oil, Gas Material Specification: Component Material Body Cast lron ASTM A126 Class B Cover Cast lron ASTM A126 Class B Screen Stainless Steel AISI 304 Gasket PTFE/Graphite Plug Ductile lron ASTM A Standard Screens: Nominal Size (mm) Hole Dia. (mm) Free Flow Area (%) Dimensions: NominalSize/ Inch mm A B Blow Off mm inch mm in BSP/NPT Weight kg 21/ / / / / / / / /8 1-1/ / /8 1-1/ Note: 1.Flanged to BS 4504 PN16,ANSI Class Other flange types available, specify on order. 3.Design and materials are subject to change without notice. -17-

22 Fireriser Butterfly Valve Wafer Type Butterfly Valves, UL, ULC Listed HPW Wafer Type, Sizes: 2-1/2, 3, 4, 6, 8 Fig.No.:HPW Specifications Working Pressure: 300 PSI (21 Bars). Max. Test Pressure : 600 PSI (42.8 Bars) Max. Working Temp: 250 F (120 ) Factory installed UL, listed double Tamper Switches For indoor and Outdoor Use. Primary Materials: Component Material Body ASTM A-536 Nylon-11 Coated Disc ASTM B-536 EPDM Encapsulated Upper&Lower Stems AISl 420-SS Worn Gear Shaft AISl 410-SS Housing ASTM A-536 Hand Wheel ASTM A-536 Flag indicator ASTM A-536 Shear Pin ASTM A-510 Segment Gear ASTM B-148 or B-584 Housing Gasket EPDM Grade"E" O-Rings(All) EPDM Grade"E" H Dimensions (mm/in): Size In/mm A B C D E F G 2-1/2/ (136) 3.43 (87) 1.81 (46) 5.89 (149.4) 6.54 (166) 5.31 (135) 5.04 (128) 0.32 (8.2) 3/ (143) 3.66 (93) 1.81 (46) 6.62 (168.2 ) 6.81 (173) 5.31 (135 ) 5.04 (128) 0.57 (4.9) 4/ (156) 4.29 (107) 2.06 (52) 7.89 (200.2 ) 7.32 (186) 5.31 (135 ) 5.04 (128) 0.89 (22.7) 6/ (188) 5.67 (144 ) 2.20 (56) 10.6 (269.8 ) 8.58 (218) 8.66 (193) 8.66 (222) 1.79 (44.4) 8/ (222) 6.54 (166) 2.28 (58) 13.0 (330.2 ) 9.92 (252 ) 8.66 (193 ) 8.66 (222 ) 2.72 (69.1) --

23 Fireriser Butterfly Valve Grooved Butterfly Valves, UL ULC Listed Fig.No.:HPG Specifications Working Pressure: 300 PSI (21 Bars) Max. Test Pressure : 600 PSI (42.8 Bars) Max. Working Temp: 250 F (120 ) Factory installed UL, listed double Tamper Switch For indoor and Outdoor Use. Primary Materials: Component Material Body ASTM A-536 Nylon-11 Coated Disc ASTM B-536 EPDM Encapsulated Upper&Lower Stems AISl 420-SS Worn Gear Shaft AISl 410-SS Housing ASTM A-536 Hand Wheel ASTM A-536 Flag indicator ASTM A-536 Shear Pin ASTM A-510 Segment Gear EPDM Grade "E" ASTM B-148 or B-584 Housing Gasket EPDM Grade"E" O-Rings(All) EPDM Grade"E" Dimensions (mm/in): Size In/mm A B C D E F G H 2-1/2" 4.1 (106) 3.3 (85) 3.80 (96.4) 2.8(73.0) 5.31 (136) 5.04 (128) 5.04 (128) 3" 4.4 (112) 3.6 (92) 3.80 (96.4) 3.50(83.9) 5.99 (142) 5.04 (128) 5.04 (128) 4" 5.7 (145) 4.34 (108) 4.54 (115.4) 4.50(114.3) 6.89 (173) (128) 5.04 (128) 6" 7.1 (180) 5.7(146) 5.21 (132.4) 6.6(168.3) 8.23 (209) 8.66 (220 ) 8.66 (220) 0.28 (7.10) 8" 8.98 (224) 6.7 (170 ) 5.80 (147.4) 18.63(219.1) 9.21 (234) 8.66 (220 ) 8.66 (220) 0.9 (24.0) 10" 8.98(224) 7.88 (200) 6.26 (199) 10.75(273) (256) 9.65 (245) (289) 12" 10.52(267) 9.14(232) 6.50 (65.1) 11.10(297) 9.65 (245) 9.65 (245) (289) --

24 Fireriser Butterfly Valve Grooved Butterfly Valves, UL ULC Listed Two Tapped Outlets Fig.No.:HPGT Specifications Working Pressure: 300 PSI (21 Bars) Max. Test Pressure : 600 PSI (42.8 Bars) Max. Working Temp: 250 F (120 ) Factory installed UL listed double Tamper Switches For indoor and Outdoor Use. Primary Materials: Component Material Body ASTM A-536 Nylon-11 Coated Disc ASTM B-536 EPDM Encapsulated Upper&Lower Stems AISl 420-SS Worn Gear Shaft AISl 410-SS Housing ASTM A-536 Hand Wheel ASTM A-536 Flag indicator ASTM A-536 Shear Pin ASTM A-510 Segment Gear ASTM B-148 Housing Gasket EPDM Grade"E" O-Rings(All) EPDM Grade"E" Dimensions (inch/mm): Size In/mm A B C D E F G H N M 2-1/2/ /2-14NPT 3/ /2-14NPT 4/ /2-14NPT 6/ /4-14NPT 8/ /4-14NPT -0-

25 Fireriser Butterfly Valve Wafer Type Butterfly Valves, UL, ULC Listed DW Wafer Type, Sizes: 2-1/2, 3, 4, 6, 8 Fig.No.:DW Universal wafer Type Butterfly Valve Suitable for Connecting to ANSI B 16 Class 125, ISO 2084/Din 2501 PN 16 & BS 4504 PN 16 Flanges Specifications Working Pressure: 175 PSI (12.5 Bars) Max. Test Pressure : 350 PSI (25.0 Bars) Max. Working Temp: 250 F (120 ) Factory installed UL, listed double Tamper Switch For indoor and Outdoor use Primary Materials: Component Material Body ASTM A-536 EMPE Encapsulated Disc ASTM B-548 or B-148 Upper&Lower Stems AISl 420-SS Worn Gear Shaft AISl 410-SS Housing ASTM A-536 Hand Wheel ASTM A-536 Flag indicator ASTM A-536 Shear Pin ASTM A-510 Segment Gear ASTM B-148 Housing Gasket EPDM Grade"E" O-Rings(All) EPDM Grade"E" Dimensions (mm/in): Size A B C D E F G H 2-1/2/ (106) 3.3 (85) 1.8 (46) 3.6 (92) 5.3 (135) 5.3 (135) 4.9 (125) 0.4 (9.5) 3/ (112) 3.6 (92) 1.8 (46) 4.2 (107) 5.6 (142) 5.3 (135) 4.9 (125) 0.6 (16) 4/ (145) 4.34 (108) 2.0 (52) 5.0 (128) 6.9 (175) 5.3 (135) 4.9 (125) 1.0 (25) 6/ (180) 5.7 (146) 2.2 (56) 7.1 (181) 8.3 (210) 7.6 (193) 8.9 (225) 1.8 (45.3) 8/ (204) 6.7 (170) 2.4 (60) 9.2 (234) 9.1 (232) 7.6 (193) 8.9 (225) 2.7 (68.5) --

26 Fireriser Butterfly Valve Fig.No.:DG Specifications Working Pressure: 175 PSI (12.5 Bars) Max. Test Pressure : 350 PSI (25.0 Bars) Max. Working Temp: 250 F (120 ) Factory installed UL listed Double Tamper Switch For indoor and Outdoor Use. Primary Materials: Component Material Body ASTM A-536 Nylon-11 Coated Disc ASTM B-536 EPDM Encapsulated Upper&Lower Stems AISl 420-SS Worn Gear Shaft AISl 410-SS Housing ASTM A-536 Hand Wheel ASTM A-536 Flag indicator ASTM A-536 Shear Pin ASTM A-510 Segment Gear ASTM B-148 Housing Gasket EPDM Grade"E" O-Rings(All) EPDM Grade"E" Dimensions (mm/in): Size A B C D E F G H 2-1/2" 4.1 (106) 3.3 (85) 3.7(94.6) 2.9(73.0) 5.31 (135) 5.3 (135) 4.9 (125) 3" 4.4 (112) 3.6 (92) 3.8 (96.4) 3.50(83.9) 5.6 (142) 5.3 (135) 4.9 (125) 4" 5.7 (145) 4.34 (108) 4.5 (114.4) 4.6 (116.2) 6.9 (175) 5.3 (135) 4.9 (125) 6" 7.1 (180) 5.7(146) 5.3 (133.4) 6.6(168.3) 8.3 (210) 7.6 (193 ) 8.9 (225) 0.28 (7.10) 8" 8.0 (204) 6.7 (170 ) 5.8 (147.4) 8.6 (219.1) 9.1 (232) 7.6 (193 ) 8.9 (225) 0.9 (24.0) --

27 Fireriser Butterfly Valve Bronze Butterfly Valve, UL, ULC Listed/FM Approved BG Grooved End, Size: 2, and 2-1/2 Fig.No.:BG Specifications Working Pressure: 175 PSI (12.5 Bars) Max. Test Pressure : 350 PSI (25.0 Bars) Max. Working Temp: 250 F (120 ) Factory installed UL, Listed Double Tamper Switch Approved For indoor and Outdoor Use. Primary Materials: Component Material Body ASTM B-505 Disc ASTM B-548 EPDM Encapsulated Upper Stem ASTM A-564 Type XM12 Lower Stem ASTM A-564 Type XM12 Gear Housing Cover ASTM A-619 Hand Wheel ASTM A-619 Flag indicator ASTM B-16 Yoke Mechanism ASTM A-283 Stem Bushing ASTM B-16 Conduit Connector ASTM A-307 O-Rings EPDM Grade"E" Cover Gasket NBR9 Dimensions (inch/mm) Size A B C D E F G 2/ (114) 2.41 (60.3) 2.29 (57.15) 0.64 (16) 0.32 (8 ) 1.96 (49) 3.62 (90.5) 2-1/2/ (114) 3.0 (75) 2.75 (69. 1) 0.64 (16) 0.32 (8) 2.18 (54.5) 3.82 (95.5 ) -23-

28 Fireriser Butterfly Valve Bronze Butterfly Valves, UL, ULC Listed/FM Approved BT Size: 1", 1-1/4", 1-1/2", 2" and 2-1/2" Fig.No.:BT Specifications Working Pressure: 175 PSI (12.5 Bars) Max. Test Pressure : 350 PSI (25.0 Bars) Max. Working Temp: 250 F (120 ) Factory installed UL Listed Double Tamper Switch for indoor and Outdoor Use. F G C Primary Materials: Component Material Body ASTM B-506 Disc ASTM B-548 EPDM Encapsulated Upper Stem ASTM A-564 Type XM12 Lower Stem ASTM A-564 Type XM12 Gear Housing Cover ASTM A-619 Hand Wheel ASTM A-619 Flag indicator ASTM B-16 Yoke Mechanism ASTM A-283 Stem Bushing ASTM B-16 Conduit Connector ASTM A-307 O-Rings (All) EPDM Grade"E" Cover Gasket NBR Dimensions (Inch/mm) Size In/mm A B C D E F G 1/ (43.7) 1.56 (39.7) 2.16 (54) 2.08 (52) 1.48 (52) / (54) 196 (47) 2.68 (67) 2.24 (56) 1.64 (41) / (60) 2.24 (70) 2.92 (73) 2.36 (90) 2.45 (61.3) / (70) 2.8 (70) 3.3 (82.4) 2.56 (54) 1.96 (49) 2-1/ (90) 3.36 (84) 4.16 (104) 2.78 (69.5) 2.18 (54.5) -24-

29 Fireriser Installation Guide Grooved valves should be connected the piping system with approved couplings or flange adapters. Flow may be from either direction, and the valve may be positioned in any direction. Fivalco butterfly valves have been designed with a slow close hand wheel operator which effectively minimizes water hammer. These valves valves feature minimum pressure loss restriction and pressure loss when in the fully open position. Design Requirements When the valves are received from the manufacturer they should be handled carefully to avoid breakage and damage to the seating area. Before installation of the valve, clean piping, flange and coupling. When the valves closes hard, it is usually due to debris lodged in the sealing area. Often this may be corrected by backing off the hand wheel and closing again. Valves should be installed indoors away from direct sunlight. Installation The valve should never be forced to seat by applying a wrench to the hand wheel as this may distort the valve components or score the sealing surface. The use of excessive force to open or close the valve violates all warranties, whether express or implied. The inlet and outlet pipe adjacent to the valve should be properly supported to prevent excessive stress on the valve body. The valve should not be uses to force a pipeline into position as this will result in distortion of the valve body. Care &Maintenance Conduit and electrical connections to the optional tamper switch must be in accordance with National Electrical Code (NFPA 72)or requirements of the local authority having jurisdiction. Fivalco butterfly valves require no regular maintenance, however, it is advisable to inspect and verify proper operation of the unit annually or in accordance with the authority having jurisdiction. Inspection should include a visual check for leakage at the valve pipe connections and body to operator connection. Inspection and maintenance should be performed by a qualified inspection service. Switch Installation Butterfly valves are provided with internal supervisory tamper switches operated by a cam connected to the valve stem. The switch will change position and close within two (2)full turn of the hand wheel from the fully open position. Gate valves should be provided with an external approved tamper switch. Switch #1 : Switch#2 For connection to the supervisory circuit. Auxiliary switch connected per Authority. Normally closed :2Red Normally closed:1red -25-

30 Fireriser Butterfly Valve Butterfly Valves Packing Firefly BT&BG UT Listed FM Nom. Pipe Size Bronze Butterfly Valves End Connection Quantity Carton/Case Weight Each Weight Packaging Weight Carton/Case In. mm Lbs /Kilos Lbs/Kilos 1" (25) TH 4 3.4/ / /4" (32) TH 4 3.7/ / /2" (40) TH 4 4.1/ /7.6 2" (50) TH 4 501/ / /2" (65) TH 4 6.7/ " (50) GR(M) 4 5.0/ / /2" (65) GR(M) 4 5.7/ /10.0 Fireriser BG&HDG Ductile Iron Body Butterfly Valves Grooved Cases Only 2-1/2" (65) GR / / /2" (76M) GRM / /475 3" (80) GR / /500 4" (100) GR / /480 6" (150) GR / /408 6" (165M) GRM / /408 8" (200) GR 24 51/0/ /528 10" (250) GR / /405 12" (300) GR / /535 Fireriser DW&HDW Ductile Iron Body Butterfly Valves Suitable for ANSI B ,DIN 2633ft DN2501 PN16 Wafer British Standard 4504/PN 16 Flanges 2-1/2" (65) w / /475 3" (80) w / /525 4" (100) w / /400 6" (150) W / /432 8" (200) W / /468 Note :GR-Grooved End. TH Threaded End. W-Wafer Type. GRV-Grooved Metric End. THM Threaded Metric End. Crate Dimensions :2-1/2 "to 4" (1.10m L 1.10m W 0.61mm H) Crate Dimensions :6" and 8" (1.10m L 1.10m W 0.76mm H) Crate Dimensions :10" and 12" TBA -26-

31 Fivalco Inc Limited Warranty Fivalco Inc, warrants each metal valve to be free from defects in material and workmanship under normal use and service for a period of one year from the date of purchase. In the event that any defect is discovered which may be covered by this warranty, the owner should contact Fivalco Inc, in writing or by telephone. The owner may be instructed to return the valve at owner's expense to Fivalco Inc, or an authorized Fivalco location for inspection. In the case that inspection reveals that the valve is defective it will be replaced at Fivalco lnc.'s expense. Replacements shall be shipped free of charge to the owners provided that the valve was installed in accordance with Fivalco Inc. Instructions and in accordance with the local authority having jurisdiction. To the extent permitted by law this warranty specifically excludes incidental and consequential damages of every type and description resulting from any claimed defect in material or workmanship, including, but not limited to, personal injuries and property damage. To the extent permitted by law, implied warranties of merchantability and fitness for particular purposes are limited in duration. Some jurisdictions do not allow exclusion or limitation of incidental damages and such limitations may not apply to you. This warranty provides the owner with specific legal rights and owners may have other rights which vary by jurisdiction. Distributed by -27-

32 Website: E - m a i l : mikokokcn@yahoo.com/ chrisfivalcovalves@yahoo.com.cn