SMALL BLOCK CHEVROLET SUPERCHARGER SYSTEM
|
|
- Angelica O’Brien’
- 5 years ago
- Views:
Transcription
1 Installation Instructions for: SMALL BLOCK CHEVROLET SUPERCHARGER SYSTEM Step-by-step instructions for installing the best in supercharger systems. * PREMIUM FUEL REQUIRED * TF Rev B Magnuson Products Inc 1990 Knoll Drive, Ventura, CA (805) * (805) fax magnusonproducts.com
2 INSTALLATION MANUAL Magna Charger SMALL BLOCK CHEVROLET SYSTEM GM CHEVROLET V8, C.I.D. Engines, Please take a few moments to review this manual thoroughly before you begin work: Μ ake quick parts check to make certain your kit is complete (See shipper parts list in this package). If you discover shipping damage or shortage, please call our facility immediately. Take a look at exactly what you are going to need in terms of tools, time, and experience. Review our limited warranty with care. When unpacking the supercharger kit DO NOT lift the supercharger assembly by the black plastic bypass actuator. This is pre-set from the factory and can be altered if used as a lifting point! Caution: Relieve the fuel system pressure before servicing fuel system components in order to reduce the risk of fire and personal injury. After relieving the system pressure, a small amount of fuel may be released when servicing the fuel lines or connections. In order to reduce the risk of personal injury, cover the regulator and fuel line fittings with a shop towel before disconnecting. This will catch any fuel that may leak out. Place the towel in an approved container when the job is complete. High performance engines require high performance fuel Use only premium fuel, 91 octane or better. TRICK FLOW by Magna Charger systems are manufactured to produce about 20 RWHP per pound of boost at sea level. High altitudes will produce different numbers. Our supercharger kits are designed for engines in good mechanical condition only. Installation on high mileage or damaged engines is not recommended and may result in engine failure, for which we are not responsible. Trick Flow/Magna Charger are not responsible for the engine or consequential damages. If you have any questions, please contact us. After you finish your installation and road test your vehicle, please fill out and mail in the limited warranty card, so we can add you to our files (this is important for your protection). A new fuel filter is recommended at the time of supercharger installation. Stock spark plugs and stock plug gap is recommended. Tools and Materials Required: Metric and inch wrench sets 3/8 drive metric and inch size socket sets (Standard & Deep) 3/8 and ½ drive Foot pound and inch pound torque wrenches Phillips and flat head screwdrivers Drain pan Hose cutters Hose clamp pliers Safety glasses Shop vacuum cleaner Top quality gasket cement RTV silicone adhesive Contact information: Magnuson Products Inc Magna Charger Division 1990 Knoll Drive. Ventura, CA Sales/Tech support Websites: info@magnacharger.com
3 1. Start the supercharger installation by removing the negative (-) battery with a 10mm wrench. 2. Rotate the engine so that the timing mark on the crank pulley is at TDC cylinder #1. Remove the distributor cap and mark the body where the rotor arm is pointing. Note the position of the distributor body relative to the engine i.e. the vacuum advance is pointing at cylinder #7. 3. Remove the distributor, current intake system, and intake manifold gaskets (On some engines it may be necessary to remove the valve covers as well). Place a shop towel into the lifter valley to prevent any debris getting inside of your engine. Make sure the cylinder head port faces are absolutely clean of any remaining gasket material or adhesive to ensure a good seal. 4. Install the new intake manifold gaskets supplied onto the cylinder heads using a top quality gasket adhesive, we recommend Gasgacinch. Apply the adhesive to the face of the heads and to the surface of the gaskets themselves. Allow the adhesive to dry until just sticky and then place the gaskets onto the cylinder heads carefully aligning the ports and bolt holes. 03/09 Page 3 magnacharger.com
4 5. Apply a bead of RTV Silicone adhesive around each of the four water port openings on the manifold side of the gaskets as shown. 6. Apply a heavy bead of RTV Silicone adhesive along the front and back top surfaces of the lifter valley. Ensure that the bead of silicone contacts the gaskets on both ends. 7. The following instructions are for 1986 and earlier cylinder heads (non Vortec) 1987 and later Vortec style head please skip to step #14. Using a 10mm socket wrench to remove the 8 bolts that secure the top of the manifold to the base. There are two on each side and two in the front and back. 8. Carefully remove the supercharger and manifold top from the base. Do not lift the supercharger by the black plastic Actuator! Carefully set the supercharger aside. Do not remove the bolts that secure the supercharger to the manifold top. DO NOT REMOVE THESE BOLTS! 03/09 Page 4 magnacharger.com
5 9. Install the manifold into position on the engine using the new manifold to head bolts supplied. Torque the bolts to 25Ft/Lbs. in the order shown At the front of the manifold base, just behind the water outlet/thermostat location, locate where the ends of the O-ring seal cord meet. Apply a small dab of RTV silicone to seal this small gap. 11. Carefully replace the supercharger and manifold top onto the manifold base. 12. Re-install the eight bolts previously removed that secured the manifold top to the manifold base. Torque these bolts to 9Ft/Lbs /09 Page 5 magnacharger.com
6 13. The following instructions are for 1987 and later cylinder heads (Vortec) and earlier (Non Vortec) style heads please skip to step #14. Install the supercharger and manifold into position on the engine using the new manifold to head bolts supplied. Torque the bolts to 25Ft/Lbs. in the order shown Re-install the distributor into its original location. Ensure that the rotor arm is pointing at the mark previously made. Secure the distributor with the new clamp, bolt and washer supplied Remove the three bolts that secure the factory accessory drive pulley(s) to the harmonic balancer. Install the supercharger crank drive pulley on top of the accessory drive pulley as shown using the 3/8 x 3.75 bolts supplied. Tighten these bolts just finger tight or snug for now. Loop the supercharger drive belt over the pulleys and check the alignment of the pulleys. Is the supercharger and crank pulley aligned? if not, use the shims supplied to move crank drive pulley out so that the grooves in both pulleys are parallel. Place the shims between the accessory pulley and the new S/C crank drive pulley. When the pulleys are aligned, remove the S/C drive belt, and torque the three 3/8 bolts to 33Ft/Lbs. Here are the supercharger belt tensioner bracket assembly components. Note that the longest bolt will pass through the pulley and spacer, through the bracket and then thread into the square nut supplied. 03/09 Page 6 magnacharger.com
7 17. Here is the Tensioner assembly as viewed from the rear. Note that the Square nut must fi t into the groove provided, with its offset to the middle of the bracket as shown SQUARE NUT Rear view of bracket 18. Install the tensioner bracket assembly under the supercharger nose and secure it to the front of the manifold base with the two bolt supplied. Install the mounting bolt on the right (passenger side) by passing it through the new alternator bracket supplied fi rst. New Alternator bracket bolts 19. Tighten the two mounting bolts securely and torque them to 27Ft/Lbs. Install the supercharger drive belt over the crank, tensioner and supercharger pulleys. Slide the tensioner pulley along its slot to the right side of the engine to tension the belt. Tensioner Pulley 20. The supercharger drive belt is tensioned correctly when you can just twist the belt 90 degrees with two fi ngers. 03/09 Page 7 magnacharger.com
8 21. On the back of the supercharger are vacuum ports for PCV, power brake connections. The Boost port is for carburetor power valve and boost gauge etc. connections. Actuator Vacuum ports Sneeze valve Boost Port Complete the installation the same as you would a standard intake system adding the carburetion, throttle linkage, thermostat and water outlet as normal. It is Very Important to use a high quality air fi lter on a supercharger installation or supercharger damage may result! Carburetion notes: The inlet port of this supercharger is confi gured to accept most popular four-barrel carburetors. We recommend use of at least a 750 CFM carburetor with mechanical secondaries. As most carburetors are not confi gured for supercharged operation, we strongly recommend you consult your carburetor manufacturer for recommended modifi cations such as boost registered power valves etc. Ignition tuning: The ignition timing will need to be re-adjusted (retarded) before the vehicle can be driven. It will be necessary to retard the ignition timing two degrees for every pound of boost that the supercharger delivers. This supercharger will supply 5-7 psi as delivered, so if you are currently running 28 degrees total mechanical advance with out vacuum, you will need to retard your ignition timing to degrees. A little careful experimentation will yield the best power. Detonation must be avoided! Use of an after market Boost/ Timing Controller such as the MSD Boost Timing Master 5462 is recommended for most applications. Test drive vehicle for the fi rst few miles under normal driving conditions, listen for any noises, vibrations, engine miss fi re or anything that does not seem normal. The supercharger does have a slight whining noise under boost conditions, which is normal. After the initial test drive gradually work the vehicle to wide open throttle runs, listen for any engine detonation (pinging). Use only premium fuel, 91 octane or better. If engine detonation is present let up on the throttle immediately and re-adjust your ignition timing. If you have questions about your vehicles performance, please check with your installation facility or call Magna Charger at (805) , Monday through Friday, 8 a.m. to 3 p.m. 03/09 Page 8 magnacharger.com
INTERCOOLED SUPERCHARGER SYSTEM FORD 5.4L 3V F-150 TRUCK
Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2004-2006 FORD 5.4L 3V F-150 TRUCK Step-by-step instructions for installing the best in supercharger systems. 89-89-65-001 Rev C Magnuson
More informationEdelbrock E-Force RPM Carburetor Supercharger C.I.D. Small-Block Chevy
Edelbrock E-Force RPM Carburetor Supercharger 302-400 C.I.D. Small-Block Chevy 1986 and Earlier Style Heads: 1513, 1514, 15131, 15133, 15141, 15143 E-Tec and Vortec Style Heads: 1515, 1516, 15151, 15153,
More informationInstallation Instructions for: HOT ROD SUPERCHARGER SYSTEM
Installation Instructions for: HOT ROD SUPERCHARGER SYSTEM 89-89-57-007 Step-by-step instructions for installing the best in supercharger systems. Magnuson Products Inc 1990 Knoll Drive, Ventura, CA. 93003
More informationBEFORE BEGINNING INSTALLATION
EDELBROCK E-FORCE SUPERCHARGER KITS Catalog #1551, 15511, 1552, 15521, 1553, 15531, 1554, 15541, 15611, 15621, 15631, 15641 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning
More informationBEFORE BEGINNING INSTALLATION
EDELBROCK E-FORCE SUPERCHARGER KITS Part #1551, 15511, 1552, 15521, 1553, 15531, 1554, 15541, 15611, 15621, 15631, 15641 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning
More informationEdelbrock E-Force RPM Carburetor Supercharger Chevrolet LS Engines
Carburetors and air cleaner sold separately. Edelbrock E-Force RPM Carburetor Supercharger Chevrolet LS Engines Rectangular Port Heads: 1511, 15111, 15113 Cathedral Port Heads: 1512, 15121, 15123 Page
More informationEdelbrock E-Force rpm carburetor Supercharger c.i.d. Small-Block chevy
Edelbrock E-Force rpm carburetor Supercharger 302-400 c.i.d. Small-Block chevy 1986 and Earlier Style Heads: 1513, 1514, 15131, 15133, 15141, 15143 E-Tec and Vortec Style Heads: 1515, 1516, 15151, 15153,
More informationInstallation Instructions for: Radix. INTERCOOLED SUPERCHARGER SYSTEM 2008 Hummer H3-Alpha
Installation Instructions for: Radix INTERCOOLED SUPERCHARGER SYSTEM 2008 Hummer H3-Alpha Step-by-step instructions for installing the best in supercharger systems. ATTENTION! Your MAGNA CHARGER intercooler
More informationInstallation Instructions for: CORVETTE SUPERCHARGER SYSTEM LT4 Z06 CORVETTE
Installation Instructions for: CORVETTE SUPERCHARGER SYSTEM 2015+ LT4 Z06 CORVETTE Step-by-step instructions for installing the HeartBeat of supercharger systems. * PREMIUM GASOLINE FUEL REQUIRED * ATTENTION!
More informationEdelbrock Enforcer EFI Supercharger C.I.D. Small-Block Chevy
Photo may not represent actual product. 302-400 C.I.D. Small-Block Chevy 1986 and Earlier Style Heads: 1520, 1521, 15201, 15211, 15203, 15213 E-Tec and Vortec Style Heads: 1522, 1523, 15221, 15231, 15223,
More informationInstallation Instructions for: Radix Retro. Intercooled Supercharger System GM 4.8L & 5.3L TRUCKS
Installation Instructions for: Radix Retro Intercooled Supercharger System 07-13 GM 4.8L & 5.3L TRUCKS Step-by-step instructions for installing the best in supercharger systems. * PREMIUM GASOLINE FUEL
More informationInstallation Instructions for: Radix Retro. Intercooled Supercharger System GM 4.8L & 5.3L TRUCKS
Installation Instructions for: Radix Retro Intercooled Supercharger System 07-10 GM 4.8L & 5.3L TRUCKS Step-by-step instructions for installing the best in supercharger systems. * PREMIUM FUEL REQUIRED
More informationInstallation Instructions for: Radix Retro. Intercooled Supercharger System GM 4.8L & 5.3L SUV s
Installation Instructions for: Radix Retro Intercooled Supercharger System 07-13 GM 4.8L & 5.3L SUV s Step-by-step instructions for installing the best in supercharger systems. * PREMIUM GASOLINE FUEL
More informationInstallation Instructions for: CORVETTE SUPERCHARGER SYSTEM 1997 TO 2004 C5 & Z06 CORVETTE
Installation Instructions for: CORVETTE SUPERCHARGER SYSTEM 1997 TO 2004 C5 & Z06 CORVETTE Step-by-step instructions for installing the best in supercharger systems. * PREMIUM FUEL REQUIRED * ATTENTION!
More informationINTERCOOLED SUPERCHARGER SYSTEM Dodge Challenger 6.1 Liter HEMI
Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2009+ Dodge Challenger 6.1 Liter HEMI Step-by-step instructions for installing the best in supercharger systems. * PREMIUM FUEL REQUIRED *
More informationFORD MUSTANG 5.0L
Installation instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2011-2013 FORD MUSTANG 5.0L Step-by-step instructions for installing the best in supercharger systems. * PREMIUM FUEL REQUIRED * ATTENTION!
More informationINTERCOOLED SUPERCHARGER SYSTEM 2004 PONTIAC GTO
Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2004 PONTIAC GTO 89-89-60-013 Rev. F Step-by-step instructions for installing the best in supercharger systems. Magnuson Products Inc 1990
More informationWEIAND STREET WARRIOR INTAKE MANIFOLD P/N s 8125, 8125P, 8126, & 8126P SMALL BLOCK CHEVROLET
APPLICATIONS: WEIAND STREET WARRIOR INTAKE MANIFOLD P/N s 8125, 8125P, 8126, & 8126P 262-400 SMALL BLOCK CHEVROLET INSTALLATION INSTRUCTIONS The P/N 8125 & 8126 WEIAND STREET WARRIOR series intake manifolds
More informationSupercharger System Chevrolet Silverado1500 & GMC Sierra 1500 Light Duty Sport Trucks
Installation Instructions for: Radix-NI Supercharger System 2003-2006 Chevrolet Silverado1500 & GMC Sierra 1500 Light Duty Sport Trucks 89-89-59-003 Rev C Step-by-step instructions for installing the best
More informationInstallation Instructions for: Radix Max. Intercooled Supercharger System GM 6.0L & 6.2L TRUCKS
Installation Instructions for: Radix Max Intercooled Supercharger System 07-13 GM 6.0L & 6.2L TRUCKS Step-by-step instructions for installing the best in supercharger systems. * PREMIUM GASOLINE FUEL REQUIRED
More informationInstallation Instructions for: JEEP CHEROKEE 6.1 Liter HEMI INTERCOOLED SUPERCHARGER SYSTEM
Installation Instructions for: 2006-10 JEEP CHEROKEE 6.1 Liter HEMI INTERCOOLED SUPERCHARGER SYSTEM Step-by-step instructions for installing the best in supercharger systems. * PREMIUM FUEL REQUIRED *
More informationSUPERCHARGER SYSTEM LT1 Chevrolet Camaro
HeartBeat Installation Instructions for: SUPERCHARGER SYSTEM 2016-2017 LT1 Chevrolet Camaro NON-INTERCOOLED Step-by-step instructions for installing the best in supercharger systems * PREMIUM GASOLINE
More informationWEIAND INTAKE MANIFOLD P/N 7550 SMALL BLOCK CHEVROLET 3x2 BBL
WEIAND INTAKE MANIFOLD P/N 7550 SMALL BLOCK CHEVROLET 3x2 BBL INTAKE MANIFOLD INSTALLATION INSTRUCTIONS 199R10703 APPLICATIONS: The P/N 7550 WEIAND intake manifold is designed for Holley 3x2 BBL, model
More informationInstallation Instructions for: Radix. Intercooled Supercharger System GM 4.8L & 5.3L SUV S Only
Installation Instructions for: Radix Intercooled Supercharger System 07-10 GM 4.8L & 5.3L SUV S Only Step-by-step instructions for installing the best in supercharger systems. * PREMIUM FUEL REQUIRED *
More informationPERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 351-M/400 c.i.d. Ford V8 CATALOG #2172 INSTALLATION INSTRUCTIONS
PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 351-M/400 c.i.d. Ford V8 INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new camshaft. If you have any questions
More informationInstallation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM
Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *
More informationInstructions for: Toyota 5.7L Coupler Replacement
Instructions for: Toyota 5.7L Coupler Replacement * PREMIUM GASOLINE FUEL REQUIRED * ATTENTION! Your MAGNUSON SUPERCHARGER kit is sensitive to corrosion! Use only the vehicle manufacturer recommended coolant
More informationInstallation Instructions for: Radix. INTERCOOLED SUPERCHARGER SYSTEM L Chevrolet Trailblazer SS
Installation Instructions for: Radix INTERCOOLED SUPERCHARGER SYSTEM 2006-2007 6.0L Chevrolet Trailblazer SS Step-by-step instructions for installing the best in supercharger systems. ATTENTION! Your MAGNA
More informationINTERCOOLED SUPERCHARGER SYSTEM PONTIAC GTO LS2
Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2005-2006 PONTIAC GTO LS2 Step-by-step instructions for installing the best in supercharger systems. Magnuson Products Inc 1990 Knoll Drive,
More informationInstallation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM
Installation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM 1996-2002 4Runner 1997-1998 T100 1997-2004 Tacoma 2000-2003 Tundra * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg
More information10-RIB BELT SYSTEM UPGRADE INSTALLATION MANUAL
10-RIB BELT SYSTEM UPGRADE INSTALLATION MANUAL 2011-2017 AND UP FORD MUSTANG GT 5.0L COYOTE WHIPPLE SUPERCHARGERS 3292 NORTH WEBER AVE FRESNO, CA 93722 TEL 559.442.1261 FAX 559.442.4153 WWW.WHIPPLESUPERCHARGERS.COM
More informationWEIAND X-CELerator Intake Manifold P/N 7516
WEIAND X-CELerator Intake Manifold P/N 7516 351C FORD, 2V CYLINDER HEADS INSTALLATION INSTRUCTIONS APPLICATIONS: The P/N 7516 X-CELerator intake manifold is designed for square-bore carburetor applications
More informationInstallation Instructions for: RAM 5.7 Liter HEMI INTERCOOLED SUPERCHARGER SYSTEM
Installation Instructions for: 2014-2015 RAM 5.7 Liter HEMI INTERCOOLED SUPERCHARGER SYSTEM Step-by-step instructions for installing the best in supercharger systems. * PREMIUM GASOLINE FUEL REQUIRED *
More informationINSTALLATION INSTRUCTIONS
PERFORMER RPM CAMSHAFT / LIFTERS / LUBE KIT For 343-401 c.i.d. AMC V8 Engines CATALOG # 7132 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most
More informationEDELBROCK THUNDER SERIES AVS CARBURETORS Part #1801, 1802, 1803, 1804, 1805, 1806, 1812, 1813, 1825, 1826 INSTALLATION INSTRUCTIONS
EDELBROCK THUNDER SERIES AVS CARBURETORS Part #1801, 1802, 1803, 1804, 1805, 1806, 1812, 1813, 1825, 1826 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation.
More informationGENERAL INSTRUCTIONS. PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: c.i.d. Chevrolet V8 Engines CATALOG #2117
Page 1 PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 283-400 c.i.d. Chevrolet V8 Engines GENERAL INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations
More information10-rib belt system upgrade Installation Manual
10-rib belt system upgrade Installation Manual 2011-2017 and up Ford MUSTANG gt 5.0l coyote WHIPPLE SUPERCHARGERS 3292 NORTH WEBER AVE FRESNO, CA 93722 TEL 559.442.1261 FAX 559.442.4153 A color PDF of
More informationPERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7102 MODEL: c.i.d. Chevrolet V8, 1957 & later
PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7102 MODEL: 262-400 c.i.d. Chevrolet V8, 1957 & later CAMSHAFT: Edelbrock Performer RPM camshafts are ground specifically for use with the corresponding
More informationINTERCOOLED SUPERCHARGER SYSTEM Dodge Challenger 5.7 Liter HEMI
Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2009-10 Dodge Challenger 5.7 Liter HEMI Step-by-step instructions for installing the best in supercharger systems. * PREMIUM GASOLINE FUEL
More informationPERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT CATALOG # 2103 MODEL: 400 c.i.d. Chevrolet V8 engines GENERAL INSTRUCTIONS
PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT CATALOG # 2103 MODEL: 400 c.i.d. Chevrolet V8 engines GENERAL INSTRUCTIONS Please study these instructions carefully before you remove your stock camshaft.
More informationPERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7102 MODEL: c.i.d. Chevrolet V8, 1957 & later
PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7102 MODEL: 262-400 c.i.d. Chevrolet V8, 1957 & later PLEASE study these instructions carefully before installing your new camshaft. If you have any questions
More informationJeep Wrangler 3.6L V-6 INTERCOOLED SUPERCHARGER SYSTEM
Installation Instructions for: 2012 + Jeep Wrangler 3.6L V-6 INTERCOOLED SUPERCHARGER SYSTEM PREMIUM GASOLINE FUEL REQUIRED ATTENTION: Your MAGNUSON SUPERCHARGER kit is sensitive to corrosion! Take care
More informationPERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7194 MODEL: c.i.d. Chrysler V8, 1968 & later
PERFORMER RPM Camshaft/Lifters/Lube Kit MODEL: 413-426-440 c.i.d. Chrysler V8, 1968 & later PLEASE study these instructions carefully before installing your new camshaft. If you have any questions, do
More informationIntercooled Supercharger System , 2007 Classic GM Trucks, 4.8L, 5.3L & 6.0L
Installation Instructions for: Radix Retro Intercooled Supercharger System 2003-2006, 2007 Classic GM Trucks, 4.8L, 5.3L & 6.0L * PREMIUM GASOLINE FUEL REQUIRED * Step-by-step instructions for installing
More informationTORKER-PLUS Camshaft/Lifters/Lube Kit CATALOG #5002 MODEL: c.i.d. Chevrolet V8
PLEASE study these instructions carefully before installing your new camshaft. If you have any questions or problems, do not hesitate to call our Technical Hotline at: 1-800-416-8628. CAMSHAFT: Edelbrock
More informationInstallation Instructions for: Sierra 5.3/6.2L DI INTERCOOLED SUPERCHARGER SYSTEM
Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM Step-by-step instructions for installing the best in supercharger systems. * PREMIUM GASOLINE FUEL REQUIRED * ATTENTION! Your MAGNUSON SUPERCHARGER
More informationEDELBROCK THUNDER SERIES AVS CARBURETORS Part #1801, 1802, 1803, 1804, 1805, 1806, 1812, 1813, 1825, 1826 INSTALLATION INSTRUCTIONS
EDELBROCK THUNDER SERIES AVS CARBURETORS Part #1801, 1802, 1803, 1804, 1805, 1806, 1812, 1813, 1825, 1826 INSTALLATION INSTRUCTIONS IMPORTANT NOTE: Proper installation is the responsibility of the installer.
More informationPerformer-Plus Camshaft/Lifters/Lube Kit Part #2182 For 351-Windsor Ford V8 Engines Installation Instructions
Performer-Plus Camshaft/Lifters/Lube Kit For 351-Windsor Ford V8 Engines Installation Instructions PLEASE study these instructions carefully before installing your new camshaft. If you have any questions
More informationInstallation Instructions for: Sierra 5.3/6.2L DI
Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM Step-by-step instructions for installing the best in supercharger systems. * PREMIUM GASOLINE FUEL REQUIRED * ATTENTION! Your MAGNUSON SUPERCHARGER
More informationThe M7 Direct Flow Intercooler (DFIC) Installation Guide
The M7 Direct Flow Intercooler (DFIC) Installation Guide This information is meant only as a guide. The author of this information,, or any M7 Tuning employees assumes no liabilities for any outcomes resulting
More informationINTERCOOLED SUPERCHARGER SYSTEM 2008 PONTIAC G8
Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2008 PONTIAC G8 Step-by-step instructions for installing the best in supercharger systems. * PREMIUM FUEL REQUIRED * ATTENTION! Your MAGNA
More informationRZR SUPERCHARGER KIT INSTALLATION INSTRUCTIONS POLARIS RZR 1000 SUPERCHARGER KIT. 1 of 33
POLARIS RZR 1000 SUPERCHARGER KIT 1 of 33 POLARIS RZR 1000 SUPERCHARGER KIT Part Number(s): 150-17-1000 TABLE OF CONTENTS Introduction / Pre-Installation Instructions C.A.D. Drawings Pre-Installation /
More informationINTERCOOLED SUPERCHARGER SYSTEM PONTIAC G8 GT (6.0L)
Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2008-2009 PONTIAC G8 GT (6.0L) Step-by-step instructions for installing the best in supercharger systems. * PREMIUM FUEL REQUIRED * ATTENTION!
More informationSupercharger Installation Instructions
Supercharger Installation Instructions Toyota 22R The Camden Supercharger System utilizes a roots type supercharger developed specifically for automotive engine applications. The present supercharger design
More informationHolley GM BBC Single-Plane EFI Intake Manifold Kits
Holley GM BBC Single-Plane EFI Intake Manifold Kits 300-561 Oval Port, 4150 Flange 300-562 Oval Port, 4500 Flange 300-563 Rectangular Port, 4150 Flange 300-564 Rectangular Port, 4500 Flange INSTALLATION
More informationPerformer RPM Camshaft/Lifters/Lube Kit CATALOG #7106 MODEL: c.i.d. Ford V8
Performer RPM Camshaft/Lifters/Lube Kit MODEL: 352-428 c.i.d. Ford V8 PLEASE study these instructions carefully before installing your new camshaft. If you have any questions or problems, do not hesitate
More informationPERFORMER-PLUS Camshaft/Lifters/Lube Kit CATALOG #2157 MODEL: c.i.d. Pontiac V8, 1965 & later
PERFORMER-PLUS Camshaft/Lifters/Lube Kit CATALOG #2157 MODEL: 350-455 c.i.d. Pontiac V8, 1965 & later CAMSHAFT: Edelbrock Performer-Plus camshafts are ground specifically for use with the corresponding
More informationTORKER-PLUS Camshaft/Lifters/Lube Kit Part #5022 MODEL: c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines)
TORKER-PLUS Camshaft/Lifters/Lube Kit MODEL: 289-302 c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines) PLEASE study these instructions carefully before installing your new camshaft.
More information1-3/4" or 1-7/8" headers Aftermarket/re-curved distributors
TORKER-PLUS Camshaft/Lifters/Lube Kit #5062 for 1967 & later 396-454 c.i.d. Chevrolet (not for use in 1965-66 396 & 427 engines requiring grooved rear journal) PLEASE study these instructions carefully
More informationTIMING BELT COMPONENTS EM 15
ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work
More informationAlways wear safety glasses when working on your vehicle.
90-93 MAZDA MIATA SUPERCHARGER KIT The KraftWerks 90-93 Mazda Miata Supercharger Kit was designed for easy installation. Competent mechanics with the appropriate tools will find the process to be relatively
More informationInstallation Instructions for: Toyota 4Runner and FJ Cruiser
Installation Instructions for: 2010-2017 Toyota 4Runner and 2010-2014 FJ Cruiser Step-by-step instructions for installation of the supercharger system. * PREMIUM GASOLINE FUEL REQUIRED * ATTENTION! Your
More informationPERFORMER-PLUS Camshaft/Lifters/Lube Kit #2177 MODEL: c.i.d. Chrysler V8, 1967 & later (Not for 1985 & later 318 V8 with roller lifters)
PERFORMER-PLUS Camshaft/Lifters/Lube Kit #2177 MODEL: 318-360 c.i.d. Chrysler V8, 1967 & later (Not for 1985 & later 318 V8 with roller lifters) PLEASE study these instructions carefully before installing
More informationFord Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours
Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Tools Required: Ratchet and socket set Torque wrench Large adjustable wrench Needle nose pliers A dozen
More informationPERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7112 MODEL: c.i.d. Oldsmobile V8, 1967 & later
PERFORMER RPM Camshaft/Lifters/Lube Kit MODEL: 330-350-403 c.i.d. Oldsmobile V8, 1967 & later PLEASE study these instructions carefully before installing your new camshaft. If you have any questions or
More informationFREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How
1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines
More informationPerformer-Plus 5.0L Hydraulic Roller Lifter Camshaft only CATALOG #3722 MODEL: 5.0 Litre Ford V8, 1985 & later INSTRUCTIONS
Performer-Plus 5.0L Hydraulic Roller Lifter Camshaft only CATALOG #3722 MODEL: 5.0 Litre Ford V8, 1985 & later INSTRUCTIONS PLEASE study these instructions carefully before installing your new camshaft.
More informationPERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7122 MODEL: c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines)
PERFORMER RPM Camshaft/Lifters/Lube Kit MODEL: 289-302 c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines) PLEASE study these instructions carefully before installing your new camshaft.
More informationInstallation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM CADILLAC CTS-V
Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2004-2005 CADILLAC CTS-V Rev. A Step-by-step instructions for installing the best in supercharger systems. Magnuson Products Inc 3172 Bunsen
More informationMSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor PN 8394 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue
More information2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar
COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top
More informationQUICK FUEL TECHNOLOGY HOT ROD SERIES CARBURETORS SLAYER SERIES CARBURETORS SUPER STREET SERIES CARBURETORS
QUICK FUEL TECHNOLOGY Installation Instructions HOT ROD SERIES CARBURETORS SLAYER SERIES CARBURETORS SUPER STREET SERIES CARBURETORS HR-580-VS 580 CFM Vac. Secondary!!! SS-680-VS 680 CFM Vac. Secondary
More informationMSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor PN 8394 - U.S. Patent 6820602 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Digital E-Curve Distributor 1 - Rotor,
More informationFront Drive System - Big Block Chevy Installation Instructions Big Block Chevy with AC & with PS
Front Drive System - Big Block Chevy Installation Instructions Big Block Chevy with AC & with PS All American Billet Store (800) 764-0926 www.allamericanbilletstore.com Items needed for install Jack Jack
More information1988 Ford F-350 PICKUP
1988 Ford F-350 PICKUP Submodel: Engine Type: V8 Liters: 7.5 Fuel Delivery: FI Fuel: GAS 1987 93 4.9L Engine The intake and exhaust manifolds on these engines are known as combination manifolds and are
More informationALL AMERICAN BILLET. Front Drive System - Small Block Ford Installation Instructions
ALL AMERICAN BILLET Front Drive System - Small Block Ford Installation Instructions Small Block Ford with AC & PS All American Billet Store (800) 764-0926 www.allamericanbilletstore.com Items needed for
More information2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #
2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009
More informationBA /02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07)
BA-2020-00/02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07) Page: 1 Revision: 6.2-02/23/2011 Install Time: 1.5 Hours We recommend a qualified Yamaha technician install this kit
More informationMSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572
MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever
More informationInstallation Instructions
CHEVROLET ENGINE SYSTEM, NON-EMISSION 1967-1987 SMALL BLOCK CHEVROLET Part Number 300-502 CHEVROLET ENGINE SYSTEM, NON-EMISSION 1962-1987 CHEVROLET 302, 327, 350 C.I.D. ENGINES Part Number 300-503-1 Installation
More information1992 Toyota Cressida
Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May
More informationPrerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More informationOwner smanual. Banks Ram-Air Intake System Ford 5.4L F150 Trucks. with Installation Instructions THIS MANUAL IS FOR USE WITH KIT 41806
Owner smanual with Installation Instructions Banks Ram-Air Intake System 2004-2008 Ford 5.4L F150 Trucks THIS MANUAL IS FOR USE WITH KIT 41806 Gale Banks Engineering 546 Duggan Avenue Azusa, ca 91702 (626)
More informationMSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572
MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572 Important: Read these Instructions before attempting the installation. Note: An MSD Ignition is required with this
More informationDrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationBBK Intake Manifold Kit ( L) - Installation Instructions
BBK Intake Manifold Kit (86-93 5.0L) - Installation Instructions The below installation instructions work for the following products: BBK Intake Manifold Kit (86-93 5.0L) Please read through the instructions
More informationINTERCOOLED SUPERCHARGER SYSTEM LS3/L99 Chevrolet Camaro
HeartBeat Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2013-2015 LS3/L99 Chevrolet Camaro Step-by-step instructions for installing the best in supercharger systems. * PREMIUM GASOLINE
More informationSpecial Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationL Intake Manifold Part #
86-93 5.0L Intake Manifold Part #5001-5002 I N S T A L L A T I O N I N S T R U C T I O N S Supplied Materials Bottom cover, Upper manifold, Lower manifold, Plenum cover plate, 1501 Throttle body (comes
More informationTork Tech Inc. Customer Service , Sales
Tork Tech Inc. Customer Service 971.226.9006, Sales 513.697.0060 Email: Info@TorkTech.com www.torktech.com * PREMIUM FUEL MANDATORY * Make sure vehicle has 91+ octane gas in it prior to beginning installation.
More information1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
More informationMSD Billet VW Distributor PN 8485
MSD Billet VW Distributor PN 8485 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD
More informationSlingshot Rotrex Supercharger Kit
Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you
More informationTypical Install Instructions
Typical Install Instructions Read & understand all steps of these instructions before beginning this installation. WEBER Conversion Kit, VW T-1/2, up to 1835cc 32 / 36 DFEV Weber Carburetor These instructions
More information1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST
1/6/04 1501 Industrial Way N., Toms River, NJ 08755 732-349-2109 Fax:732-244-0867 MODERATE - Installation requires metric tools and possibly cutting and drilling. The ability to closely follow instructions
More informationINTERCOOLED SUPERCHARGER SYSTEM CADILLAC CTS-V
Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2004-2005 CADILLAC CTS-V 89-89-60-015 Rev C Step-by-step instructions for installing the best in supercharger systems. Magnuson Products Inc
More informationBefore continuing with the installation, here are a few definitions you should be aware of:
MSD Pro-Billet Distributor Cadillac V8 (368, 425, 472, 500), PN 8363 AMC V8, PN 8519 Jeep Inline-6, PN 8516 Chevrolet Inline-6 (194, 230, 250, 292), PN 8515 ONLINE PRODUCT REGISTRATION: Register your MSD
More informationSLP Camaro ZL1 STAGE 3 (650 HP)
SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1
More informationWARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More information