QIS Hardwired Roller Shade User Manual
|
|
- Matthew Chase
- 5 years ago
- Views:
Transcription
1 QIS Hardwired Roller Shade User Manual SPRING SIDE BRACKET (Spindle Clip) MOTOR SIDE BRACKET (Spindle Key-hole) ROLLER SHADE END CAP END CAP FASCIA MOUNTING SCREWS POWER & COMMUNICATION PANEL POWER BRICK & CORD (FOR POWER & COMMUNICATION PANEL) WALL SWITCH SINGLE AND DUAL CHANNEL (OPTIONAL) Package Contents: Hardwired Roller Shade Motor Side Bracket Spring Side Bracket End Cap x 2 Fascia (Optional) Mounting Screws Power & Communication Panel Power Brick & Cord Wall Switch (Optional) Recommended Tools: Cable Management / Cable Tie Downs Measuring Tape Power Drill with 3/32 Bit & 1/4 Nut Driver Flat Head Screwdriver #2 Phillips Head Screwdriver Level Pencil Ladder
2 CONTENTS Fascia Brackets...3 Universal Brackets...3 Outside Mount...3 Fascia Bracket Hardstop Removal...4 Fascia Bracket Installation...4 Inside Mount Standard Roll...4 Inside Mount Reverse Roll...5 Outside Mount Standard Roll...6 Outside Mount Reverse Roll...7 QIS Cable Placement...7 Shade Installation...8 Fascia Installation...9 Standard Fascia...9 Reverse Fascia...9 Universal Bracket Installation...10 Inside Mount Standard Roll...10 Inside Mount Reverse Roll...11 Outside Mount - Standard Roll...12 Outside Mount - Reverse Roll...12 Fascia End Cap Installation...13 Universal End Cap Installation...13 QIS Power & Communication Panel Setup...14 Wire Specification:...14 Maximum length of wire from Power & Communication Panel to device:...14 Maximum length or wire for Hardwired 4 and 8 Button Switches:...14 Maximum wire length for RS485 communication:...14 System Capacity:...14 Power & Communication Panel:...14 Power & Communication Panels and Third Party Integration via RS Wiring for Cat 5e/6 Cable...14 QIS Wall Switch Programming Instructions...15 First Time Setup...15 Pairing / Learning Wall Switch (or Channel)...15 Unpairing / Unlearning Wall Switch (or Channel)...15 Setting Upper and Lower Limits / Learning a New Position...15 Tug Command Mode...15 Join ZigBee Network / Identify...16 Set Lower Limit...16 Zigbee Network Reset...16 Factory Master Reset...16 FCC...17 INDUSTRY CANADA
3 CAUTION: READ AND UNDERSTAND EACH SECTION BEFORE PERFORMING REQUIRED STEPS. FAILURE TO FOLLOW PROPER PROCEDURE COULD RESULT IN DAMAGE TO THE SHADE OR PERSONAL INJURY. QMotion products are designed for use with QMotion hardware and power supplies only. Install in compliance with all local and national building and electrical codes. Always wear personal protection equipment including safety glasses and gloves. Use a ladder per its manufacturer s instructions. Before installing the shade into the window, verify that window hardware (latches, locks, window cranks, etc.) does NOT obstruct the travel path of the shade. Damage to the fabric or shade may result from repeated contact with windowhardware. FALLING HAZARD: Shades must be installed to proper support structure. Locate the shade s mounting type on the order form (Inside Mount, Outside Mount). Determine roll type (Standard Roll, Reverse Roll). Fascia Brackets For Standard Roll, the fabric rolls towards the window. The Motor Side Bracket is installed on the LEFT side of the window, and the Spring Side Bracket is installed on the RIGHT side of the window. See Fascia Bracket Installation section for further detail. For Reverse Roll, the fabric rolls toward the room. The Motor Side Bracket is installed on the RIGHT side of the window, and the Spring Side Bracket is installed on the LEFT side of the window. See Fascia Bracket Installation section for further detail. Universal Brackets When installing Universal Brackets, the bracket mounting is the same for both Standard Roll and Reverse Roll. See Universal Bracket Installation section for further detail. Outside Mount When installing the shade in an outside mount, use a measuring tape to measure and mark the Center Line of the window opening. Divide the Bracket to Bracket width (found on order form) in half. Using the half width distance, measure and mark the distance on each side of the center line. It is recommended to off-set the bottom of the brackets 1/2 above the window opening (see illustration below). Outside Mount Center Line Inside Mount 1/2 3
4 FASCIA BRACKET HARDSTOP REMOVAL When installing an outside mount, it is helpful to remove the hard stop before screwing the bracket to the wall. Hard Stop MUST be replaced for proper shade function. The hard stop is easily removed by using a flat head screw driver. Insert the flat head screw driver between the back of the hard stop and the bracket (see illustration to right). Apply a slight downward force to the top of the hard stop, while using the flat head screwdriver to eject each of the three prongs holding the hard stop in place. The hard stop prong should slide down and out. After all three prongs have been ejected, the hard stop can be tilted away from the bracket for complete removal. Replace the hard stop after mounting the bracket with the screws. Make sure that both the top and bottom of the hard stop are securely locked back in place. Failure to correctly replace the hard stop will result in improper shade function or damage. FASCIA BRACKET INSTALLATION Position the bracket flush against the side and top of the window opening. Ensure brackets are level and square. Screw placement can be through the side of the bracket, or through the top of the bracket (see illustrations). Fascia brackets should be recessed 1/8 (3mm) into the window opening. This allows the fascia to be flush with the window opening when installed. Use a pencil to mark the drill locations. With the brackets removed, use a 3/32 (2mm) drill bit to drill a pilot hole at each pencil mark. Replace the brackets, and secure them to the wall using the pre-drilled pilot holes and provided screws. Use wall anchors if necessary (not provided). Cable management shown (not provided). Inside Mount Standard Roll Fascia Bracket Hardstop Removal (Spring Side Bracket Shown) 1/8 1/8 Inside mount - Standard Roll Motor Side Bracket - Left Side Side Screw Mount Inside mount - Standard Roll Spring Side Bracket -Right Side Side Screw Mount 4
5 1/8 1/8 Inside mount - Standard Roll Motor Side Bracket - Left Side Top Screw Mount Inside mount - Standard Roll Spring Side Bracket -Right Side Top Screw Mount Inside Mount Reverse Roll 1/8 1/8 Inside mount - Reverse Roll Spring Side Bracket - Left Side Side Screw Mount Inside mount - Reverse Roll Motor Side Bracket -Right Side Side Screw Mount 5
6 1/8 1/8 Inside mount - Reverse Roll Spring Side Bracket - Left Side Top Screw Mount Inside mount - Reverse Roll Motor Side Bracket -Right Side Top Screw Mount Outside Mount Standard Roll 1/2 1/2 Outside mount - Standard Roll Motor Side Bracket - Left Side Hard Stop Removed Outside mount - Standard Roll Spring Side Bracket -Right Side Hard Stop Removed 6
7 Outside Mount Reverse Roll 1/2 1/2 Outside mount - Reverse Roll Spring Side Bracket - Left Side Outside mount - Reverse Roll Motor Side Bracket -Right Side QIS CABLE PLACEMENT Failure to properly orient and secure the QIS Cable may lead to damage of the shade or window enclosure. Cable should be routed atop of the shade fabric tube (see illustration below). Make sure the bracket spacing provides enough room to prevent pinching of the cable. Secure the cable using zip-ties or other cable management hardware so that the cable does not interfere with shade operation. CORRECT Cable Orientation INCORRECT Cable Orientation 7
8 SHADE INSTALLATION 1/2 1/2 Once the brackets are installed level and square, insert the shade into the bracket starting with the motor side. Make sure the spindle is securely seated into the spindle key-hole (see illustration above). Improperly seated motors will cause issues with shade movement. Once the motor side is in place, lift the spring side up into the bracket. The spindle should push against the bracket spring clip while inserting the shade. When the spindle has cleared the spring clip, the spring clip will spring back locking the spindle into place. Rotate the shade to ensure both spindles are fully seated into the slots. 8
9 FASCIA INSTALLATION Standard Fascia Insert the Fascia at an angle, hook the Fascia onto the front edge of both top bracket arms. 2. Rotate the Fascia down, the Fascia should pivot on the front edge of the brackets in Step Firmly push the Fascia against the bracket, the Fascia will snap onto the bottom edge of the bracket. NOTE: A single fascia center support is needed per 10 ft.(3m) of standard fascia, and two supports per 10 ft.(3m) of reverse fascia. Install the fascia center support equally spaced between the brackets. Ensure that the fascia center support is level and square to the top of the shade brackets. Reverse Fascia Insert the Fascia at an angle, hook the Fascia onto the front edge of both top bracket arms. 2. Rotate the Fascia down, the Fascia should pivot on the front edge of the brackets in Step Firmly push the Fascia against the bracket, the Fascia will snap onto the bottom edge of the bracket. 9
10 UNIVERSAL BRACKET INSTALLATION Inside Mount Standard Roll 1/2 1/2 Inside Mount - Standard Roll Side Screw Mount - Left Offset brackets 1/2 inch (13mm) from top of the window to allow proper clearance for installing shade into bracket Inside Mount - Standard Roll Side Screw Mount - Right Offset brackets 1/2 inch (13mm) from top of the window to allow proper clearance for installing shade into bracket 1/8 1/8 Inside Mount - Standard Roll Top Screw Mount - Left Inside Mount - Standard Roll Top Screw Mount - Right Illustrations above show mounting option for Universal Brackets using an inside mount. Universal Brackets can be mounted using the side screw holes (see top illustrations). Universal Brackets can also be adjusted for mounting using the alternate screw holes by removing the four screws and re-orienting the hard stop sub-bracket (see bottom illustrations). 10
11 Inside Mount Reverse Roll 1/2 1/2 Inside Mount - Reverse Roll Side Screw Mount - Left Offset brackets 1/2 inch (13mm) from top of the window to allow proper clearance for installing shade into bracket Inside Mount - Reverse Roll Side Screw Mount - Right Offset brackets 1/2 inch (13mm) from top of the window to allow proper clearance for installing shade into bracket 1/2 1/2 Inside Mount - Reverse Roll Side Top Mount - Left Offset brackets 1/2 inch (13mm) from back of the window to allow proper clearance for installing shade into bracket Inside Mount - Reverse Roll Side Top Mount - Right Offset brackets 1/2 inch (13mm) from back of the window to allow proper clearance for installing shade into bracket Illustrations above show mounting option for Universal Brackets using an inside mount. Universal Brackets can be mounted using the side screw holes (see top illustrations). Universal Brackets can also be adjusted for mounting using the alternate screw holes by removing the four screws and re-orienting the hard stop sub-bracket (see bottom illustrations). 11
12 Outside Mount - Standard Roll 1/2 1/2 Outside Mount - Standard Roll Left Side Offset brackets 1/2 inch (13mm) from top of the window Outside Mount - Standard Roll Right Side Offset brackets 1/2 inch (13mm) from top of the window Outside Mount - Reverse Roll 1/2 1/2 Outside Mount - Reverse Roll Left Side Offset brackets 1/2 inch (13mm) from top of the window Outside Mount - Reverse Roll Right Side Offset brackets 1/2 inch (13mm) from top of the window 12
13 FASCIA END CAP INSTALLATION To install Fascia End Caps, match the appropriate End Cap to the correct bracket. End Caps are labeled Left or Right. Align the End Cap posts (see illustration) with the side mount fastener locations and snap the Fascia End Cap into the bracket. For reverse fascia installations, the Fascia End Caps should be reversed to fit the corresponding brackets. NOTE: Note: If the brackets have been installed using the side screw mount (flush against the window jamb) Fascia End Caps will not be installed. UNIVERSAL END CAP INSTALLATION End caps are intended for use when the shade is OUTSIDE mounted. Use in an INSIDE mounted shade will cause damage to the shade by placing undue pressure on the shade from the sides. To install Universal End Caps, slide the End Cap onto the Universal Bracket using the notched grooves for alignment (see illustration). The Universal End Cap will fit onto either bracket. NOTE: Note: If the brackets have been installed using the side screw mount (flush against the window jamb) Universal End Caps will not be installed. 13
14 QIS POWER & COMMUNICATION PANEL SETUP CAUTION The Qadvanced Intelligent System (QIS) does not operate on standard Power of Ethernet (PoE) schemes. Do not attempt to connect the QIS to any PoE device or RJ-45 PoE port. Doing so will damage the system components and/or the external Ethernet or PoE device. Power Port Device Port (Shades and Switches) Communication Port (RS485) Use CAT5e/CAT6 wire to connect QIS shades to the Power & Communication Panel. Terminate wires using RJ-45 connectors (T568B Standard). QIS shades will Jog upon connecting power to the shade. The Amber LEDs on the Power & Communication Panel (RJ-45) ports signify power is active. The Green LEDs signify communication activity. To daisy chain additional QIS Power & Communication Panels, use either or the Communication Ports (RS485) to expand the system capabilities up to 200 devices. ZigBee Ha1.2 capabilities allow up to 60 ZigBee devices on a ZigBee network. Wire Specification: Category 5e/Category 6 for use with RJ-45 Connector 24 AWG Maximum length of wire from Power & Communication Panel to device: Up to an 8 X 8 Shade with 40:1 motor X 8 to 12 X 12 Shade with 73:1 motor Maximum length or wire for Hardwired 4 and 8 Button Switches: 1000 feet from switch to farthest power panel Maximum wire length for RS485 communication: 2000 feet from source to shade System Capacity: 200 Devices (QMotion Shades, QMotion Hardwired Switches) Power & Communication Panel: 8 RJ-45 device ports for motorized shades and switches 2 additional RJ-45 communication ports dedicated to daisy chain with other Power & Communication Panels and Third Party Integration via RS485 Power Supply Port - AC Input: VAC, 2.5A DC Output: 24 VDC, 7.5A Wiring for Cat 5e/6 Cable Pin Wire Color Signal 10/100BaseTx 1 White/Orange A+ 2 Orange B- 3 Whtie/Green +24 VDC 4 Blue +24 VDC 5 White/Blue +24 VDC 6 Green +24 VDC 7 White/Brown +24 VDC 8 Brown +24 VDC 14
15 QIS WALL SWITCH PROGRAMMING INSTRUCTIONS First Time Setup IMPORTANT Read and understand each section before performing required steps. When using a Dual Channel Wall Switch, the left button column corresponds to Channel 1. The right button column corresponds to Channel 2 as shown in the diagram below. 1. INSTALL SHADE following appropriate installation instructions 2. CONNECT POWER SUPPLY to Power Communication Panel 3. CONNECT SHADE to Power Communication Panel using network cable (Shade will JOG on initial power-up) 4. CONNECT WALL SWITCH to Power Communication Panel using network cable Pairing / Learning Wall Switch (or Channel) 1. PRESS both UP and PRESET 1 at the same time (Shade will JOG in response) 2. TUG the HEMBAR 6-10 inches (Shade will JOG in response and is now paired) Unpairing / Unlearning Wall Switch (or Channel) 1. PRESS both DOWN and PRESET 2 at the same time (Shade will JOG in response) 2. TUG the HEMBAR 6-10 inches (Shade will JOG in response and is now unpaired) CH 1 CH 2 Single Channel Wall Switch Dual Channel Wall Switch IMPORTANT When learning new positions, the button currently being programmed (after Step 3. TUG) will not send commands to the shade. Example 1: When learning a new PRESET 1 position, pressing PRESET 1 will do nothing (after Step 3. TUG). The shade can still be adjusted using the UP and DOWN buttons. Example 2: When learning a new upper limit position, the UP button is semi-disable. Only by pressing the UP button 3 times will the shade move to the up position (or manually roll the shade up by hand). After Step 5 all buttons resume full functionality. Setting Upper and Lower Limits / Learning a New Position (You must use a paired wall switch to perform this task.) 1. PRESS the (UP, DOWN, or PRESET) button that will be programmed (Shade will move to selected position) 2. PRESS and HOLD the same (UP, DOWN, or PRESET) button UNTIL shade JOGS 3. TUG shade 6-10 inches (Shade will JOG in response) 4. ADJUST shade to desired position ( Use UP/DOWN buttons or manually adjust shade by hand) 5. PRESS and HOLD the same (UP, DOWN, or PRESET) button (Shade will JOG when learned) Tug Command Mode Tug Command Mode will allow certain features to be performed manually without a learned remote. IMPORTANT Read the following instructions completely before starting the procedure. Inputs from the user are time sensitive. If the shade times out before entering a tug command, return the shade to the Upper Limit Position and begin the procedure over. To Enter Tug Command Mode 1. Start with the shade at the Upper Limit Position. 2. Perform two consecutive 6 inch tugs, waiting 1 second between tugs. (Shade will JOG, then travel up, settling a few inches below the Upper Limit Position) The shade is now in Tug Command Mode There is a 10 second opportunity to enter a tug command before the shade will leave Tug Command Mode and resume normal operation. 3. Once the shade is in Tug Command Mode, perform additional 6 inch tugs to select a command option. After each tug, the shade will return to its starting position. Once the shade returns to its starting position, wait 1 second before performing the next tug (a brake is engaged during this 1 second wait, making the shade difficult to tug). After the tug sequence is performed (1-4 Tugs), wait 5 seconds and the shade will accept the tug command. 1 Tug - Join ZigBee Network / Identify 2 Tugs - Set Lower Limit Position 3 Tugs - ZigBee Network Reset 4 Tugs - Factory Master Reset 15
16 Join ZigBee Network / Identify This command will allow the shade to join an open ZigBee network. If the shade is not connected to a ZigBee network, the shade will micro-jog while trying to find a network. Once a ZigBee network is found, the shade will seek the Upper Limit Position hardstop. If a ZigBee network is not found after 1 minute, the shade will stop micro-jogging and wait for further inputs. If the shade micro-jogs but does not find a network, make sure the ZigBee network coordinator (Qube/Range Extender) is open for devices joining the network. If the shade is already connected to a ZigBee network, the shade will continually long jog up and down for 2 minutes. Manual operation of the shade will not be available during this operation. Wait until the 2 minute long jog is complete to proceed. If the shade Identifies on a network, but is unable to pair to a remote, perform the ZigBee Network Reset tug command and then connect the shade to the correct ZigBee network. Set Lower Limit This command will allow the Lower Limit Position to be adjusted without a remote. The shade will travel to the current Lower Limit Position and then jog. Manually adjust the shade to the desired Lower Limit Position. To set this new position as the Lower Limit Position, leave the shade to idle for 1 minute. After the 1 minute has passed, the shade will jog to confirm the new Lower Limit Position. Zigbee Network Reset This command will remove the shade from its current ZigBee network. This command will also delete any groups/scenes that are stored on the shade. Tugging the shade after a ZigBee Network Reset will cause the shade to micro-jog and search for an open ZigBee network. Factory Master Reset This command will perform a ZigBee Network Reset as well as restore the Upper & Lower Limits Positions and Intermediate Set-points to their default values. Tugging the shade after a Factory Master Reset will cause the shade to micro-jog and search for an open ZigBee network. 16
17 FCC Warning: Changes or modifications to this device not expressly approved by QMotion could void the user s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. INDUSTRY CANADA Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d un type et d un gain maximal (ou inférieur) approuvé pour l émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l intention des autres utilisateurs, il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l intensité nécessaire à l établissement d une communication satisfaisante. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence. L exploitation est autorisée aux deux conditions suivantes: (1) l appareil ne doit pas produire de brouillage, et (2) l utilisateur de l appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d en compromettre le fonctionnement. QdR REMOTE Model: QZR-ZIG2400 FCC ID: 2ABLX-ZIG24DECO IC: 8832A-ZIG24DECO ROLLER SHADE Model: QMRS-240Z FCC ID: 2ABLX-240Z IC: 8832A-240Z European Representative Doug Fiske Contact for QMotion Raritan Europe B.V. Jan van Galenstraat JG Schiedam The Netherlands For more information visit us at qmotionshades.com or call QMotion. QMotion is a trademark. All rights reserved. Pub # Revised: 05/2017
(SB2) (SB1) (SB3) (SB5) (SB4) Cylindrical Installation Instructions. A. CHECKLIST (4 each AA Batteries Included) (SB1) (SB4) (SB2) (SB6) (SB6) (SB3)
A. CHECKLIST (4 each AA Batteries Included) FOR DOOR AND FRAME PREPARATION INSTRUCTIONS, SEE APPENDIX A OR GO TO PROXESS.COM Parts List: Each Proxess C-Series lockset includes Exterior lock assembly (include
More informationCHARGING FOLIO. for iphone 6 USER GUIDE
CHARGING FOLIO for iphone 6 USER GUIDE GETTING STARTED Welcome Congratulations on your recent purchase of a Case-Mate charging folio! The charging folio gives your iphone 6 up to 125% extra battery life*
More informationOwner s Manual Embedded Solutions. Low Profile (Model Number: LPIC-L0001) Puck (Model Number: LPIC-P0001) Standard Profile (Model Number: LPIC-S0001)
Owner s Manual Embedded Solutions Low Profile (Model Number: LPIC-L0001) Puck (Model Number: LPIC-P0001) Standard Profile (Model Number: LPIC-S0001) 1 Advisory & Safety Information Page 2 of 14 Advisory
More informationCertification Exhibit FCC ID: SK9OW1 IC: 864G-OW1. FCC Rule Part: IC Radio Standards Specification: RSS-247. ACS Project Number:
Certification Exhibit FCC ID: SK9OW1 IC: 864G-OW1 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-247 ACS Project Number: 16-0295 Manufacturer: Itron, Inc. Model: OW1 Manual 5015 B.U. Bowman
More information& Mattel and Smart Toy LLC. All Rights Reserved. and designate U.S. trademarks of Mattel, except as noted. DNV
1 UNITED STATES 1-800-432-5437 Fisher-Price, Inc. 636 Girard Avenue, East Aurora, NY 14052 Hearing-impaired consumers: 1-800-382-7470 CANADA 1-800-432-5437 Mattel Canada Inc. 6155 Freemont Blvd. Mississauga,
More informationAutomated Coupled Roller Shade Instruction Manual. link. Coupled Shade System 2.6 and 3.3 Bracket Standard Roll Inside or Outside Mount
Automated Coupled Roller Shade Instruction Manual link Coupled Shade System 2.6 and 3.3 Bracket Standard Roll Inside or Outside Mount WARNING: Read and understand all instructions to avoid damage or injury.
More informationApple, iphone and ipad are trademarks of Apple Inc., registered in the U.S. and other countries. Android is a trademark of Google Inc.
1 UNITED STATES 1-800-432-5437 Fisher-Price, Inc. 636 Girard Avenue, East Aurora, NY 14052 Hearing-impaired consumers: 1-800-382-7470 CANADA 1-800-432-5437 Mattel Canada Inc. 6155 Freemont Blvd. Mississauga,
More informationTouchstone TB130 DC Output UPS
Touchstone TB130 DC Output UPS User Guide Release 2.5 STANDARD 1.0 August 2017 August 2017 Touchstone TB130 DC Output UPS User Guide Release 2.5 STANDARD 1.0 ARRIS Copyrights and Trademarks 2017 ARRIS
More informationUser s Manual BRONCO THE RC TRICERATOPS VTech Printed in China US
User s Manual BRONCO THE RC TRICERATOPS 2014 VTech Printed in China 91-002928-006 US Hi Friend, You re about to embark on a dino-mite adventure with me, Bronco the RC Triceratops! Just so you know, I ve
More informationP
P7639 Please keep this instruction sheet for future reference, as it contains important information. Requires four AA batteries (included) for operation. Adult assembly is required. Tool required for assembly:
More informationHP10325 KIT. AMP Wireless Air Controls
HP10325 KIT AMP Wireless Air Controls Take control of your air springs through the AMP Wireless Control application. Requires Air Springs and Onboard Air Systems (sold separately). + Download_on_the_ Download_on_the_
More informationRES+ Owner's Guide SMARTPHONE OPERATION KEY FOB OPERATION CT 200h TVIP V9 REMOTE ENGINE STARTER PLUS (RES+) OWNER S GUIDE
2011- CT 200h TVIP V9 REMOTE ENGINE STARTER PLUS (RES+) OWNER S GUIDE RES+ Owner's Guide SMARTPHONE OPERATION KEY FOB OPERATION 04-25-14 090002-36700700 SMARTPHONE OPERATION KEY FOB OPERATION TABLE OF
More informationwww.fisher-price.com P6246 R2772 P6248 P6247 Each sold separately and subject to availability. Vehicles shown in illustrations may be different than the vehicle included with your toy. 1 Battery Installation
More informationRIDESENSE User Manual
RIDESENSE User Manual RIDESENSE overview: The GIANT RIDESENSE employs ANT+ and Bluetooth Smart (BLE 4.0) license certification technology. ANT+: ANT+ certification compliant meter. Bluetooth Smart (BLE
More informationPark Daddy Installation Manual
Manual Version: 07.10.2017 Park Daddy Installation Manual MODEL PD50AA MODEL PD100AA TABLE OF CONTENTS Introduction..... 2 Package Contents..... 3 Unpacking.......3 Installing Infrared Head Units......
More informationInstaller Guide smart connect
Installer Guide smart connect TM 7490 Wireless Remote Outdoor Sensor Please read all instructions before proceeding. The wireless remote outdoor sensor monitors temperature at a remote outdoor location
More informationY9854. fisher-price.com
Y9854 Please keep this instruction sheet for future reference, as it contains important information. Requires two AA (LR6) alkaline batteries for operation (not included). Adult assembly is required. Tool
More informationV9961 V9961
V9961 www.fisher-price.com Please keep this instruction sheet for future reference, as it contains important information. Adult assembly required. Requires one "AAA" battery (included). Tool required for
More informationINSTALLATION GUIDE Confidant RFID Kit 1. 3rd party Rose Mount & Back Plate PK3616
INSTALLATION GUIDE Confidant RFID Kit 1 3rd party Rose Mount & Back Plate PK3616 Confidant RFID TM Installation Instructions (Kit 1) IMPORTANT: Wear Safety glasses before starting the replacement of parts.
More informationBFK51 CFD40 CHM41. fisher-price.com
BFK51 CFD40 CHM41 Please keep this instruction sheet for future reference, as it contains important information. Requires three AA (LR6) alkaline batteries (not included). Adult assembly is required. Tool
More informationX0056. fisher-price.com
X0056 Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Requires three button cell (LR44) alkaline batteries (included). Batteries
More informationPatriot II Braking System
Please visit www.blueox.com for the latest version of these installation instructions. Owner s Manual & Installation Instructions THANK YOU for purchasing a Patriot II braking system from Blue Ox. We ve
More informationPlease keep this instruction sheet for future reference, as it contains important information. Requires three AA batteries for operation (included).
Please keep this instruction sheet for future reference, as it contains important information. Requires three AA batteries for operation (included). Adult assembly is required. Tool required for battery
More informationPress the buttons for fun sounds and music! fisher-price.com
K7189 Press the buttons for fun sounds and music! fisher-price.com Please keep these instructions for future reference, as they contain important information. Requires three button cell (LR44) batteries
More informationW1392. fisher-price.com
W1392 Please keep this instruction sheet for future reference, as it contains important information. Requires three C batteries (LR14) alkaline batteries (not included) for operation. Adult assembly is
More informationXM Series. Quick Start Guide. Technology at Work XMCom9
XM Series Quick Start Guide Technology at Work. 062411XMCom9 Copyright 2011 Janam Technologies LLC. All rights reserved. XM Series, Janam and the Janam logo are trademarks of Janam Technologies LLC. Other
More informationPlease keep this instruction sheet for future reference, as it contains important information. Requires three AA batteries (included) for operation. Adult assembly is required. Tool required for battery
More informationT
T4262 Please keep this instruction sheet for future reference, as it contains important information. Maximum weight: 44 lbs. (20 kg). For ages between 9 months and 3 years. Requires three AA batteries
More informationTractor Interface Module Installation Instructions. Switch Input (TIM-SI)
Tractor Interface Module Installation Instructions Switch Input (TIM-SI) 821-7002 Installation Instructions Tractor Interface Module Switch Input (TIM-SI) 821-7002 Getting Started... 1 Installing the TIM...
More informationW9740. fisher-price.com. 2 Ride. 1 Sit. 3 Walk
W9740 2 Ride 1 Sit 3 Walk Please keep this instruction sheet for future reference, as it contains important information. For ages 9 36 months and up to 44 lbs (20 kg). Adult supervision is required. Never
More informationW9740. Ride. Sit. Walk. fisher-price.com
W9740 Ride Sit Walk Please keep this instruction sheet for future reference, as it contains important information. For ages 9 36 months and up to 44 lbs (20 kg). Adult supervision is required. Never use
More informationInstallation Instructions RF4510-EA
Installation Instructions RF4510-EA HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 1 Product Description Dimensions Orientation Compatibility Access Control Systems Proximity Cards Frequency
More informationHOMELINK DOOR OPENER KIT
HOMELINK DOOR OPENER KIT P/N 2882082 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More informationUser Manual TX MHz PowerSpot Transmitter
TX91503 915 MHz PowerSpot Transmitter PRODUCT DESCRIPTION The Powercast TX91503 Powercaster transmitter is specially designed to provide both power and data to end devices containing the Powercast s power
More informationWARNING. To prevent entanglement injury, never place gym in a crib or playpen. Never add strings, ties or other products to the gym.
X7299 WARNING To prevent entanglement injury, never place gym in a crib or playpen. Never add strings, ties or other products to the gym. Please keep this instruction sheet for future reference, as it
More informationT Overhead Gym. Tummy Time Fun. On-the-Go Fun
T6339 Please keep this instruction sheet for future reference, as it contains important information. Requires four AA (LR6) alkaline batteries for operation (not included). Tool required for battery installation:
More informationCFM96. fisher-price.com
CFM96 Keep this instruction sheet for future reference, as it contains important information. Requires four C (LR14) alkaline batteries (not included) for operation. Adult assembly is required. Tool required:
More informationX7298. fisher-price.com WARNING
X7298 WARNING To prevent entanglement injury, never place gym in a crib or playpen. Never add strings, ties or other products to the gym. Please keep this instruction sheet for future reference, as it
More informationX2916. fisher-price.com WARNING. Overhead Gym. Tummy Time Fun
X2916 Overhead Gym Tummy Time Fun WARNING To prevent entanglement injury, never place gym in a crib or playpen. Never add strings, ties or other products to the gym. Please keep this instruction sheet
More informationT6339. Remove the mobile from the hub and clip to a stroller for on-the-go entertainment!
T6339 Remove the mobile from the hub and clip to a stroller for on-the-go entertainment! Please keep this instruction sheet for future reference, as it contains important information. Requires four AA
More informationW
W0275 Actual product may vary from the photos. Please keep this instruction sheet for future reference, as it contains important information. Requires four "AA" (LR6) alkaline batteries (not included)
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board WARNING WARNING WARNING. Support
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application: Jeep Wrangler 2-Door 2007-2016 Part Number 75651-15 Installation Tips Read and follow, precisely, all installation
More informationWASP-P PRESSURE SENSOR
WASP-P PRESSURE SENSOR USER MANUAL VERSION 03.22 15/03/2016 WASP is a registered trademark owned by BossPac Engineering & Technology WASP is a PATENT PENDING technology owned by BossPac Engineering & Technology
More informationAxon Flex, Axon Flex 2, Axon Fleet, Axon Body, Axon Body 2, Axon Dock, and Axon Signal Vehicle Unit Warnings, Instructions & Information
This document presents important safety warnings, instructions, and information intended to minimize hazards associated with the use of Axon Enterprise, Inc. s (Axon) Axon camera systems. These instructions
More informationAuto-Lift Operating System
Installation Instructions Parasol Cellular Shades Auto-Lift Operating System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 STEP 1
More informationAS-RFK2315. User Guide. Two-Way FM LED Remote System. Available functionalities depend on vehicle. Consult your dealer for more information.
Two-Way FM LED Remote System AS-RFK2315 User Guide Available functionalities depend on vehicle. Consult your dealer for more information. Designed & engineered in Canada INDUSTRY CANADA USER NOTICE: Operation
More informationH3-EM Electronic Swinghandle Operating Instructions
H3-EM-67-100 Electronic Swinghandle Operating Instructions Package Contents H3-EM-67-x00 Electronic Swinghandle with Proximity Reader (qty1) EM-0-45827 M3x25 POZIDRIV Mounting Screws (qty 4) EM-0-47151
More informationAurora Dreamband Quickstart Guide
Aurora Dreamband Quickstart Guide Say Hello to Aurora Aurora is a comfortable wearable sleep solution. The soft neoprene headstrap has built-in brainwave sensors to accurately track and stage sleep. Whether
More informationfisher-price.com BMH49 CHY39 BMD80 Lay & play Take-along
BMH49 CHY39 BMD80 Lay & play Tummy time Sit & play Take-along Keep this instruction sheet for future reference, as it contains important information. Requires three AA batteries (included) for operation.
More informationR
R3858 Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Tools required for assembly: Phillips Screwdriver, Hammer and Scrap Block
More informationW3599
www.fisher-price.com W3599 Please keep this instruction sheet for future reference, as it contains important information. Requires two "AAA" batteries (included) for vehicles. Requires six "AAA" (LR03)
More informationCHG26 IMAGINEXT. Requires four AA (LR6) alkaline batteries (not included) for operation.
1,5V x 4 AA (LR6) Keep this instruction sheet for future reference, as it contains important information. Requires four AA (LR6) alkaline batteries (not included) for operation. Adult assembly is required.
More informationIN100. with Aperio Technology. Mortise Lock Installation Instructions
IN100 with Aperio Technology Mortise Lock Installation Instructions A8122A 6/12 Copyright 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or
More informationCHG26 IMAGINEXT. Requires four AA (LR6) alkaline batteries (not included) for operation.
1,5V x 4 AA (LR6) Keep this instruction sheet for future reference, as it contains important information. Requires four AA (LR6) alkaline batteries (not included) for operation. Adult assembly is required.
More information*504471* Instruction Manual for the. Akrapovič Sound Kit. Sound Remote Controller and Akrapovič Car Sound Kit App Manual FOR CARS
Instruction Manual for the Akrapovič Sound Kit *504471* Sound Remote Controller and Akrapovič Car Sound Kit App Manual FOR CARS Ver 1.2 / January 2016 Akrapovič Sound Kit CONGRATULATIONS Congratulations
More informationAir Lift Performance 3S
Air Lift Performance 3S Control System P A T E N T E D AD-955 (011807) ERN 8639 USER GUIDE For maximum effectiveness and safety, please read these instructions completely before operating. Failure to read
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board WARNING WARNING WARNING. Support
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application: Jeep Wrangler 2-Door 2007-2016 Part Number 75151-15 Installation Tips Read and follow, precisely, all installation
More informationDHC26 FDT63. fisher-price.com
DHC26 FDT63 Keep this instruction sheet for future reference, as it contains important information. Requires three AA batteries (included) for operation. Batteries included are for demonstration purposes
More informationLEVOLOR. Sheer Shadings. Persianas traslúcidas Stores diaphanes INSTALLATION OPERATION CARE
LEVOLOR Sheer Shadings Persianas traslúcidas Stores diaphanes INSTALLATION OPERATION CARE INSTALACIÓN FUNCIONAMIENTO CUIDADO INSTALLATION FONCTIONNEMENT ENTRETIEN all 1 2 3 open close Battery Powered Motorized
More informationV-D2425 and V-D2440 Digital Clock
Installation Manual V1.03 V-D2425 and V-D2440 Digital Clock Valcom, Inc. V-D2425 and V-D2440 Wired Clock Table of Contents Table Installation of Contents 2 Instructions Flush Mount Installation 3 3 Wall
More informationAssembly. Care. Snap the third wheel into the socket into the back of this toy.
DRN78 Keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. No tools are needed for assembly. Requires four C (LR14) alkaline batteries (included)
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board WARNING WARNING WARNING. Skill Level. Installation Time
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application: Jeep Wrangler Unlimited 2007-2016 Part Number 75652-15 Installation Tips Read and follow, precisely, all installation
More informationSafety information. English
English Safety information To prevent injury to yourself and others or damage to your device, read the safety information about your device before using the device Samsung cannot be held responsible for
More informationBFT56 CKB84. fisher-price.com. Keep this instruction sheet for future reference, as it contains important information.
BFT56 CKB84 Keep this instruction sheet for future reference, as it contains important information. Battery installation is required. Only adults should install batteries. Tool required for battery installation:
More informationP Volt Charger Each sold separately and subject to availability.
P6828 6-Volt 4 Amp/Hr Battery P6829 6-Volt Charger Each sold separately and subject to availability. IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS. For use with a Power Wheels toddler vehicle
More informationInstruction Manual for the. Akrapovič Sound Kit. For Mercedes C63 AMG
Instruction Manual for the Akrapovič Sound Kit For Mercedes C63 AMG Ver 1.0 / March 2016 Akrapovič Sound Kit CONGRATULATIONS - Congratulations on purchasing the Akrapovič Sound Kit. The Akrapovič Sound
More informationPASSPORT Cylindrical Lock Installation Instructions A8013H 04/16
P2 PASSPORT 1000 Cylindrical Lock Installation Instructions A8013H 04/16 Copyright 2015, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part
More informationFGF37. Requires three AA (LR6) alkaline batteries (not included) for operation. For longer life, use alkaline batteries.
1,5V x 3 AA (LR6) Keep these instructions Battery installation is required. for future reference as Only adults should install they contain important batteries. Tool required for information. battery installation:
More information2-WAY REMOTE STARTING SYSTEM WITH 1 BUTTONS FOR AUTOMATIC TRANSMISSION RED301-2WAY / ANT-2WDSS. User Guide For Key
2-WAY REMOTE STARTING SYSTEM WITH 1 BUTTONS FOR AUTOMATIC TRANSMISSION RED301-2WAY / ANT-2WDSS User Guide For Key This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled
More informationInstallation Guide(s)
FCC Part 15 Transmitter Certification Test Report FCC ID: SPI-4XXKPMR FCC Rule Part: 15.09 ACS Report Number: 05-070-15C Manufacturer: Single Access Lock Inc. Model: 4XXKP/MR Installation Guide(s) 5015
More informationInstallation instructions
Installation instructions Akrapovič Exhaust System: Sound Kit for the BMW M2 (type F87) ENGLISH Version 1.0 07/2016 www.akrapovic.com Installation instructions Akrapovič Exhaust System: Soun Kit for the
More informationInstruction Manual for the. Akrapovič Sound Kit. For BMW M2. Ver 1.0 / June 2016
Instruction Manual for the Akrapovič Sound Kit 505451 For BMW M2 Ver 1.0 / June 2016 Akrapovič Sound Kit CONGRATULATIONS - Congratulations on purchasing the Akrapovič Sound Kit. The Akrapovič Sound Kit
More informationLow voltage transformer AGInode device REX2 single phase option. Introduction
February 2012 IL42-5005D Introduction Low voltage transformer AGInode device REX2 single phase option The Elster low voltage (LV) transformer AGInode device brings EnergyAxis System metering and network
More informationHendrickson Fit Adapter Installation Instructions
Hendrickson Fit Adapter Installation Instructions Hendrickson Fit Adapter (HFA) Installation Manual Table of Contents Pre-Installation Requirements... 3 Clocking Wheels...3 HFA Hubcap Installation... 4
More informationLED Recessed Troffer Retrofit Kit
Model # TRK series LED Recessed Troffer Retrofit Kit Installation Instructions PACKAGE CONTENTS A B E Part Item Name Qty. A Retrofit assembly 1 B Bracket 2 C Sheet metal screw 4 D Wire nuts 5 E Gap channel
More informationNWCTRL3024 INTELLIGENT SOLAR CHARGE CONTROLLER INSTALLATION AND OPERATION MANUAL. Thank you for purchasing NetWave from ComNet.
INTELLIGENT SOLAR CHARGE CONTROLLER Thank you for purchasing NetWave from ComNet. The NetWave controller is an intelligent and multifunctional solar charge controller. The customized LCD display screen
More informationPASSPORT Cylindrical Lock. Installation Instructions A8033G 04/16
P1 PASSPORT 1000 Cylindrical Lock Installation Instructions A8033G 04/16 Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part
More informationBattery-Powered Motorized System
Installation, Operation and Care Instructions Battery-Powered Motorized System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 STEP
More informationMoonroof (if equipped) Moonroof switches
Keys and doors Keys... 2-3 Key number plate... 2-3 Immobilizer... 2-4 Certification for immobilizer system... 2-4 Security indicator light... 2-5 Key replacement... 2-5 Door locks... 2-6 Locking and unlocking
More informationInstallation instructions
Installation instructions Akrapovič Exhaust System: Sound Kit for the Porsche Boxster (type 981) Porsche Cayman (type 981) ENGLISH Version 1.0 06/2016 www.akrapovic.com Installation instructions Akrapovič
More informationIN100. with Aperio Technology. Mortise Lock Installation Instructions A8190B 07/16
IN100 with Aperio Technology Mortise Lock Installation Instructions A8190B 07/16 Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or
More informationPASSPORT Mortise Lock. Installation Instructions A8032G 04/16
P1 PASSPORT 1000 Mortise Lock Installation Instructions A8032G 04/16 Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without
More informationAS-1271/ AS-1272 AS-1271U/ AS-1272U
MANUAL / AUTOMATIC TRANSMISSION MULTI-CHANNEL REMOTE STARTER SYSTEM AS-1271/ AS-1272 AS-1271U/ AS-1272U User Guide WARNING! It is the responsibility of the vehicle operator to ensure their vehicle is parked
More informationR
R6357 www.fisher-price.com Please keep this instruction sheet for future reference, as it contains important information. Requires six AAA alkaline batteries (not included) and six button cell batteries
More informationAirVolt - P User s Manual. 3CH Mini Indoor Helicopter w/ Gyro. Ages 14+ and up
AirVolt - P16-41459 3CH Mini Indoor Helicopter w/ Gyro User s Manual Ages 14+ and up TABLE OF CONTENTS What s in the Box... 3 Helicopter Part LIst... 4 Installing the Batteries... 5 Charging the Helicopter...
More informationMonnit Wireless Range Extender Product Use Guide
Monnit Wireless Range Extender Product Use Guide Information to Users This equipment has been tested and found to comply with the limits for a Class B digital devices, pursuant to Part 15 of the FCC Rules.
More informationINSTEON Range Extender Owner s Manual
INSTEON Range Extender Owner s Manual Getting Started Contents INSTEON Range Extender 4 Device Overview Buttons Installation Placement Extending Your Network Bridging Electrical Legs 6 Functionality with
More informationUser Manual. Patent Pending Hickory, NC 28601
User Manual Patent Pending Hickory, NC 28601 Thank you for purchasing a LevelMatePRO wireless vehicle leveling system. This product was designed for ease of use and utilizes the best possible components
More informationUSE AND CARE GUIDE 15 INCH WHITE ROUND FLAT PANEL FIXTURE WITH SELECTABLE COLOR TEMPERATURE
74212 USE AND CARE GUIDE 15 INCH WHITE ROUND FLAT PANEL FIXTURE WITH SELECTABLE COLOR TEMPERATURE FEIT ELECTRIC COMPANY PICO RIVERA, CA (800) 543-3348 FAX (562) 908-6360 www.feit.com Table of Contents
More informationShort guide TU501-x / ME501-x
Short guide TU501-x / ME501-x Version 4.0, April 2018 Practical advice: 1. Save important numbers S/N xxxxxx +xx xx xx xx xx S/N xxxxxx Serial number located on the unit 2. Installation is best done outside
More informationIN100. with Aperio Technology. Cylindrical Lock Installation Instructions A8189B 07/16
IN100 with Aperio Technology Cylindrical Lock Installation Instructions A8189B 07/16 Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole
More informationAF7006 Alarming Camera Display Unit (6.5 ) AF7015 Alarming Camera Display Unit (4.5") AF7216 Camera Sensor
How to Setup a Display Unit AF700 or AF70 AF7 AF700 Alarming Camera Display Unit (. ) AF70 Alarming Camera Display Unit (.") AF7 Camera Sensor Battery-powered alarming system with AC power connections
More informationUser s Manual. Cruise & Learn CarTM VTech Printed in China US
User s Manual Cruise & Learn CarTM 2015 VTech Printed in China 91-002992-000 US INTRODUCTION Thank you for purchasing the VTech Cruise & Learn Car! Hop in and learn with the Cruise & Learn Car. Your child
More informationAS-1774 / 1774U. User Guide 5-BUTTON AUTOMATIC / MANUAL TRANSMISSION REMOTE STARTER
5-BUTTON AUTOMATIC / MANUAL TRANSMISSION REMOTE STARTER AS-1774 / 1774U User Guide WARNING! It is the responsibility of the vehicle operator to ensure that their vehicle is parked in a safe and responsible
More informationBluetooth Smart Speed/Cadence Sensor Instruction Manual
Bluetooth Smart Speed/Cadence Sensor Instruction Manual Contents Before using this product... 3 Warranty... 4 List of Parts... 4 Battery... 6 Installation... 7 Pairing... 11 Technical Specs... 11 2 WARNINGS:
More informationfisher-price.com W6138
W6138 Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Tools required for assembly: Phillips Screwdriver, Hammer and Scrap Block
More informationXG Series Quick Start Guide
XG Series Quick Start Guide Purpose-Built Technology. 040212XGcom.7 Copyright 2012 Technologies LLC. All rights reserved. XG Series, and the logo are trademarks of Technologies LLC. Other product and brand
More informationN
N8416 Please keep this instruction sheet for future reference, as it contains important information. Product features and decorations may vary from the photograph. Adult assembly is required. Tools required
More informationDOOR LIMITS A) ENGAGE CHAIN/BELT CONNECTOR TO CARRIAGE CAUTION B) CLOSE TRAVEL LIMIT
20 6 DOOR LIMITS Severe injury or death can result if the door closing force is set too high. Never increase the door closing force above the minimum required to move the door. Never adjust force to compensate
More informationParent s Guide. This guide contains important information. Please keep it for future reference US
Parent s Guide This guide contains important information. Please keep it for future reference. 91-003324-000 US INTRODUCTION The Stack & Tumble Elephant TM provides a silly twist on the classic ring stacker.
More information