AutoFarm GPS AutoSteer Hardware Installation Guide

Size: px

Start display at page:

Download "AutoFarm GPS AutoSteer Hardware Installation Guide"

Joshua Henry
5 years ago
Views:

1 AutoFarm GPS AutoSteer Hardware Installation Guide Supported Models: Maxxum MXM-175 and MXM-190 MFD, New Holland TM-190, New Holland TM-175 PN: A

2 Special Requirements Tools This list consists of special tools that are not normally needed. A complete set of common installation tools is assumed. If you find that you are using additional special tools, please notify Documentation@Novariant.com. Metric open wrenches Metric socket wrenches up to 24mm Soft brush Clean rags Oil collection pan (for collecting oil if hose connections are opened) Attention Tighten all screws, bolts, nuts, hose connections and cable connections after the final assembly of the AutoFarm Steering System on the vehicle. Technician Feedback Please contact Novariant via to Documentation@Novariant.com with: outdated pictures or instructions tips for other installers general comments or suggestions i

3 Table of Contents Special Requirements i Tools i Attention i Technician Feedback i Install Roof Module Safety Notes Install the Mounting Rail Mount the Roof Module Install the User Terminal Assemble and Mount the User Terminal Bracket Mount and Adjust the User Terminal Install the Wheel Angle Sensor (WAS) Mount Tie Rod and Sensor Brackets Adjust the Sensor and Linkage Arms Assemble and Mount the Hydraulic Valve Install the Hydraulic Valve Install the Hydraulic Hoses Route the Hydraulic Hoses AutoSteer Valve Port Connections Connect the Hydraulic Hoses Attach the Pressure Transducer Install the SA Module Mount the SA Module Bracket Mount the SA Module to the Bracket Install the Main Cable Harness Attach the Main Cable Harness to the User Terminal Attach the Cable to the Power Supply Attach the Main Cable Harness to the Roof Module Install the SA Module Cable Harness Attach the Cable to the SA Module Connect the SA Module Harness to the Hydraulic Valve Connect the SA Module Harness to the Wheel Angle Sensor Attach SA Module Cable Harness to Main Cable Harness Final Checklist ii

4 1. Install Roof Module 1.1 Safety Notes The AutoFarm system must be powered OFF when installing or removing the roof module. The supplied locking pin or a padlock must be in place whenever the vehicle is in operation. The roof module must be removed when transporting the vehicle at speeds above 30 mph. Make sure that you are in a stable position on the tractor platform when removing the roof module, so that you do not fall or drop the roof module. 1.2 Install the Mounting Rail Remove the cab roof bolts. 1

the mounting rail to the mounting rail brackets.

5 Attach the mounting rail brackets to the roof. Align the mounting rail to mounting holes and fasten the mounting rail to the mounting rail brackets. The lettered holes should be on the left side of the tractor. 2

6 1.3 Mount the Roof Module Slide the roof module into locked position. The cable connection must be on the left side of the tractor, facing the rear. cable connector Make sure that the spring lock is in place. locked position 3

locking pin Attach the radio modem antenna.

7 Insert and close the locking pin through the holes in the roof module and the mounting rail. Note that a padlock can replace the locking pin. locking pin Attach the radio modem antenna. Note: The antenna should be attached hand tight - do not use any tools to tighten the antenna. 4

8 2. Install the User Terminal 2.1 Assemble and Mount the User Terminal Bracket Mount the bracket assembly to the cab post. 2.2 Mount and Adjust the User Terminal Attach the adjustable arm to the user terminal. mounting plate 5

9 Remove the travel stop on the bracket assembly. Install user terminal arm onto the cab bracket. 6

10 Tighten the arm onto the cab bracket. Replace the travel stop. 7

11 Adjust user terminal arm tightness. Adjust user terminal viewing angle. 8

12 3. Install the Wheel Angle Sensor (WAS) 3.1 Mount Tie Rod and Sensor Brackets Mount the sensor bracket and attach the Wheel Angle Sensor. wheel angle sensor sensor bracket Mount the linkage bracket and attach the linkage arm. 9

Attach and connect the two linkage arms. 3.2 Adjust the Sensor and Linkage Arms Adjust linkage arm length and/or linkage bracket position to obtain between 3200 and 3800 counts.

13 Attach and connect the two linkage arms. 3.2 Adjust the Sensor and Linkage Arms Adjust linkage arm length and/or linkage bracket position to obtain between 3200 and 3800 counts. Turn the wheels all the way in both directions to make sure the linkage arms can move without interference. Note: This step is done during the calibration and tuning steps. 10

14 4. Assemble and Mount the Hydraulic Valve 4.1 Install the Hydraulic Valve Fasten bracket into place. valve bracket Mount the hydraulic valve. 11

15 5. Install the Hydraulic Hoses 5.1 Route the Hydraulic Hoses Route the left/right Steer In Steer Out hoses from the AutoSteer valve, under the cab, to the front right of the tractor. Note: Secure the hoses with cable ties and be sure they are clear of moving parts and heat sources. 5.2 AutoSteer Valve Port Connections Hydraulic Hose Steer In (Right) Steer In (Left) Steer Out (Right) Steer Out (Left) Pressure Return Load Sense Pressure Transducer Valve Port Label SR SL Right Left P T LS Trans 12

Connect the right Steer In hose to the bottom hose on the tractor steering unit. Connect the left Steer In hose to the top hose on the tractor steering unit.

16 5.3 Connect the Hydraulic Hoses Detach existing steer hoses. Original right and left Steering hoses that will be opened to connect the AutoSteer hoses Open the tractor s steering lines and connect AutoSteer IN/OUT hoses. Connect the right Steer In hose to the bottom hose on the tractor steering unit. Connect the left Steer In hose to the top hose on the tractor steering unit. Connect the right Steer Out AutoSteer hose to the bottom steel steering line. Connect the left Steer Out AutoSteer hose to the top steel steering line. Note: Right steering hoses must be connected to right steering lines and Left steering hoses must be connected to left steering lines. Check for oil leaks after final assembly and the tractor engine has been turned on and steered. 13

17 Connect power beyond hoses to valve. return load sense pressure Connect hoses to power beyond unit. return load sense pressure 14

5.4 Attach the Pressure Transducer Attach

Attach the pressure transducer to the 90

18 5.4 Attach the Pressure Transducer Attach the 90 degree fitting to the port marked trans on the AutoSteer valve. Note: Use teflon tape to ensure a good seal. Attach the pressure transducer to the 90 degree fitting. Note: Use teflon tape to ensure a good seal. 15

19 Attach the cable connector from the valve harness to the pressure transducer. pressure transducer cable connector make sure to line up the connectors correctly. do not force the connection. 16

20 6. Install the SA Module 6.1 Mount the SA Module Bracket Locate the area to mount the bracket. area for mounting bracket Mount the bracket. 17

21 6.2 Mount the SA Module to the Bracket Note: It is essential that the SA Module is NOT mounted so that the cable connection is on the top or on the side with the cable going up. 18

22 7. Install the Main Cable Harness 7.1 Attach the Main Cable Harness to the User Terminal. 7.2 Attach the Cable to the Power Supply 7.3 Attach the Main Cable Harness to the Roof Module Route the cable out the rear of the cab floor, behind the seat, under the floor mat. The existing hole may need to be widened or a new hole drilled. 19

23 Attach the cable to the roof module. Route the cable down the left side of the cab and secure with cable ties. 20

24 8. Install the SA Module Cable Harness 8.1 Attach the Cable to the SA Module Connect the cable to the SA Module. SA module cable connector locking mechanism in open position Close the cable connector locking mechanism. locked position 21

Note: To disconnect the cable from the SA module,

Valve Attach the two connectors from the SA Module

25 Note: To disconnect the cable from the SA module, the connector must first be unlocked as shown. pinch here pull upwards 8.2 Connect the SA Module Harness to the Hydraulic Valve Attach the two connectors from the SA Module to the hydraulic valve. (Different vehicle shown in picture.) two connectors 22

26 8.3 Connect the SA Module Harness to the Wheel Angle Sensor Route and secure the WAS cable from the SA Module beneath the cab to the WAS. 23

27 8.4 Attach SA Module Cable Harness to Main Cable Harness Route the SA Module cable into the cab through the floor of the cab behind the seat using the same hole used to route the main cable harness. (It may be necessary to drill this hole.) Attach the harnesses with two connectors. 24

28 9. Final Checklist Check all hose connections. Check all cable connections. Power up the vehicle and check for hydraulic leaks. Check manual steering. Power up the AutoSteer system and begin the calibration and tuning process. 25

AutoFarm GPS AutoSteer Hardware Installation Guide

AutoFarm GPS AutoSteer Hardware Installation Guide Supported Models: Case AFX-8010 Combines PN: 602-0039-01-A Special Requirements Tools This list consists of special tools required to complete the installation.