WIPER & WASHER SECTION WW CONTENTS DRIVER CONTROLS WW-1 BASIC INSPECTION... 3 SYSTEM DESCRIPTION... 6 ECU DIAGNOSIS INFORMATION...

Transcription

1 DRIVER CTROLS SECTI WW A WIER & WASHER B C D CTENTS E BASIC INSECTI... 3 DIAGNOSIS AND REAIR WORKFLOW... 3 Work Flow...3 SYSTEM DESCRITI... 6 FRT WIER AND WASHER SYSTEM... 6 System Diagram...6 System Description...6 Component arts Location...9 Component Description...10 DIAGNOSIS SYSTEM (BCM)...11 COMM ITEM...11 COMM ITEM : CSULT Function (BCM - COMM ITEM)...11 WIER...11 WIER : CSULT Function (BCM - WIER)...12 DIAGNOSIS SYSTEM (IDM E/R)...13 Diagnosis Description...13 CSULT Function (IDM E/R)...15 DTC/CIRCUIT DIAGNOSIS...17 WIER AND WASHER FUSE...17 Description...17 Diagnosis rocedure...17 FRT WIER MOTOR LO CIRCUIT...18 Component Function Check...18 Diagnosis rocedure...18 FRT WIER MOTOR HI CIRCUIT...20 Component Function Check...20 Diagnosis rocedure...20 FRT WIER AUTO STO SIGNAL CIR- CUIT...22 Component Function Check...22 Diagnosis rocedure...22 FRT WIER MOTOR GROUND CIRCUIT...24 Diagnosis rocedure...24 WASHER SWITCH...25 Description...25 Component Inspection...25 WASHER MOTOR CIRCUIT...26 Diagnosis rocedure...26 ECU DIAGNOSIS INFORMATI...28 BCM (BODY CTROL MODULE)...28 Reference Value...28 Terminal Layout...33 hysical Values...33 Fail Safe...49 DTC Inspection riority Chart...50 DTC Index...51 IDM E/R (INTELLIGENT OWER DISTRI- BUTI MODULE ENGINE ROOM)...54 Reference Value...54 Fail Safe...60 DTC Index...62 WIRING DIAGRAM...63 FRT WIER AND WASHER SYSTEM...63 Wiring Diagram...63 SYMTOM DIAGNOSIS...68 FRT WIER AND WASHER SYSTEM SYMTOMS...68 Symptom Table...68 FRT WIER DOES NOT OERATE...70 Description...70 Diagnosis rocedure...70 F G H I J K WW M N O WW-1

2 NORMAL OERATING CDITI Description RECAUTI RECAUTIS recaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT RE-TEN- SIER" recaution for rocedure without Cowl Top Cover REMOVAL AND INSTALLATI FRT WIER Exploded View FRT WIER BLADE REFILL FRT WIER BLADE REFILL : Removal and Installation FRT WIER BLADE FRT WIER BLADE : Removal and Installation FRT WIER ARMS FRT WIER ARMS : Removal and Installation FRT WIER DRIVE ASSEMBLY FRT WIER DRIVE ASSEMBLY : Removal and Installation FRT WASHER WASHER TUBE WASHER TUBE : Layout FRT WASHER NOZZLE FRT WASHER NOZZLE : Removal and Installation FRT WASHER NOZZLE : Adjustment WASHER TANK WASHER TANK : Removal and Installation FRT WASHER UM FRT WASHER UM : Removal and Installation WASHER LEVEL SWITCH Removal and Installation FRT WIER AND WASHER SWITCH Removal and Installation SERVICE DATA AND SECIFICATIS (SDS) SERVICE DATA AND SECIFICATIS (SDS) Specifications WW-2

3 < BASIC INSECTI > DIAGNOSIS AND REAIR WORKFLOW BASIC INSECTI DIAGNOSIS AND REAIR WORKFLOW Work Flow OVERALL SEQUENCE INFOID: A B C D E F G H I J K WW M N O DETAILED FLOW WW-3 JMKIA0101GB

4 < BASIC INSECTI > 1. GET INFORMATI FOR SYMTOM DIAGNOSIS AND REAIR WORKFLOW Get the detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). >> GO TO 2 2. CHECK DTC 1. Check DTC. 2. erform the following procedure if DTC is displayed. - Record DTC and freeze frame data (rint them out with CSULT.) - Erase DTC. - Study the relationship between the cause detected by DTC and the symptom described by the customer. 3. Check related service bulletins for information. Is any symptom described and any DTC detected? Symptom is described, DTC is displayed>>go TO 3 Symptom is described, DTC is not displayed>>go TO 4 Symptom is not described, DTC is displayed>>go TO 5 3. CFIRM THE SYMTOM Confirm the symptom described by the customer. Connect CSULT to the vehicle in DATA MITOR mode and check real time diagnosis results. Verify relation between the symptom and the condition when the symptom is detected. >> GO TO 5 4. CFIRM THE SYMTOM Confirm the symptom described by the customer. Connect CSULT to the vehicle in DATA MITOR mode and check real time diagnosis results. Verify relation between the symptom and the condition when the symptom is detected. >> GO TO 6 5. ERFORM DTC CFIRMATI ROCEDURE erform DTC Confirmation rocedure for the displayed DTC, and then check that DTC is detected again. At this time, always connect CSULT to the vehicle, and check diagnostic results in real time. If two or more DTCs are detected, refer to BCS-63, "DTC Inspection riority Chart" and determine trouble diagnosis order. NOTE: Freeze frame data is useful if the DTC is not detected. erform Component Function Check if DTC Confirmation rocedure is not included in Service Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during this check. If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirmation rocedure. Is DTC detected? YES >> GO TO 8 NO >> Refer to GI-45, "Intermittent Incident". 6. ERFORM BASIC INSECTI erform WW-3, "Work Flow". Inspection End>>GO TO 7 7. DETECT MALFUNCTIING SYSTEM BY SYMTOM TABLE Detect malfunctioning system according to WW-68, "Symptom Table" based on the confirmed symptom in step 4, and determine the trouble diagnosis order based on possible causes and symptom. >> GO TO 8 WW-4

5 DIAGNOSIS AND REAIR WORKFLOW < BASIC INSECTI > 8. DETECT MALFUNCTIING ART BY DIAGNOSTIC ROCEDURE Inspect according to Diagnostic rocedure of the system. NOTE: The Diagnostic rocedure described is based on open circuit inspection. A short circuit inspection is also required for the circuit check in the Diagnostic rocedure. Is malfunctioning part detected? YES >> GO TO 9 NO >> Check voltage of related BCM terminals using CSULT. 9. REAIR OR RELACE THE MALFUNCTIING ART 1. Repair or replace the malfunctioning part. 2. Reconnect parts or connectors disconnected during Diagnostic rocedure again after repair and replacement. 3. Check DTC. If DTC is displayed, erase it. >> GO TO FINAL CHECK When DTC was detected in step 2, perform DTC Confirmation rocedure or Component Function Check again, and then check that the malfunction has been repaired securely. When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that the symptom is not detected. Does the symptom reappear? YES (DTC is detected)>>go TO 8 YES (Symptom remains)>>go TO 6 NO >> Inspection End. A B C D E F G H I J K WW M N O WW-5

6 FRT WIER AND WASHER SYSTEM < SYSTEM DESCRITI > SYSTEM DESCRITI FRT WIER AND WASHER SYSTEM System Diagram INFOID: ABLIA2794GB System Description INFOID: OUTLINE The front wiper is controlled by each function of BCM and IDM E/R. Control by BCM Combination switch reading function Front wiper control function Control by IDM E/R Front wiper control function Relay control function FRT WIER BASIC OERATI BCM detects the combination switch condition by the combination switch reading function. BCM transmits the front wiper request signal to IDM E/R with CAN communication depending on each operating condition of the front wiper. IDM E/R turns / the integrated front wiper relay and the front wiper high relay according to the front wiper request signal. IDM E/R provides the power supply to operate the front wiper HI/LO operation. FRT WIER LO OERATI BCM transmits the front wiper request signal (LO) to IDM E/R with CAN communication according to the front wiper LO operating condition. Front wiper LO operating condition - Ignition switch - Front wiper switch LO or front wiper switch MIST (while pressing) IDM E/R turns the integrated front wiper relay according to the front wiper request signal (LO). FRT WIER HI OERATI BCM transmits the front wiper request signal (HI) to IDM E/R with CAN communication according to the front wiper HI operating condition. Front wiper HI operating condition - Ignition switch - Front wiper switch HI IDM E/R turns the integrated front wiper relay and the front wiper high relay according to the front wiper request signal (HI). FRT WIER INT OERATI WW-6

7 < SYSTEM DESCRITI > FRT WIER AND WASHER SYSTEM BCM transmits the front wiper request signal (INT) to IDM E/R with CAN communication depending on the front wiper INT operating condition and intermittent operation delay interval according to the wiper intermittent dial position. Front wiper INT operating condition - Ignition switch - Front wiper switch INT IDM E/R turns the integrated front wiper relay so that the front wiper is operated only once according to the front wiper request signal (INT). BCM detects stop position/except stop position of the front wiper motor according to the front wiper auto stop signal received from IDM E/R with CAN communication. BCM transmits the front wiper request signal (INT) again after the intermittent operation delay interval. A B C D E F NOTE: Front wiper intermittent operation can be set to the operation with vehicle speed by CSULT. Refer to BCS- 23, "WIER : CSULT Function (BCM - WIER)". Front wiper intermittent operation with vehicle speed BCM calculates the intermittent operation delay interval from the following - Vehicle speed signal (received from the combination meter with CAN communication) - Wiper intermittent dial position Wiper intermittent dial position *: When without vehicle speed setting Intermittent operation interval Vehicle stopped or less than 5 km/h (3.1 MH) Intermittent operation delay Interval (s) 5 km/h (3.1MH) or more or less than 35km/h (21.7 MH) Vehicle speed 35 km/h (21.7 MH) or more or less than 65km/h (40.4 MH)* JLIA0094GB 65 km/h (40.4MH) or more 1 Short Long FRT WIER AUTO STO OERATI BCM stops transmitting the front wiper request signal when the front wiper switch is turned. IDM E/R detects the front wiper auto stop signal from the front wiper motor and detects the front wiper motor position (stop position/except stop position). G H I J K WW M N O WW-7

8 FRT WIER AND WASHER SYSTEM < SYSTEM DESCRITI > When the front wiper request signal is stopped, IDM E/R turns the front wiper relay until the front wiper motor returns to the stop position. JLIA0095GB NOTE: BCM stops the transmitting of the front wiper request signal when the ignition switch is. IDM E/R turns the front wiper relay when the ignition switch is. FRT WIER OERATI LINKED WITH WASHER BCM transmits the front wiper request signal (LO) to IDM E/R with CAN communication according to the washer linked operating condition of the front wiper. BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 2 times when the front washer switch is detected. Washer linked operating condition of front wiper - Ignition switch - Front washer switch (0.4 second or more) IDM E/R turns the integrated front wiper relay according to the front wiper request signal (LO). The front washer motor is grounded through the combination switch when the front washer switch is. FRT WIER FAIL SAFE OERATI When the front wiper auto stop circuit is malfunctioning, IDM E/R performs the fail-safe function. Refer to CS-25, "Fail Safe". WW-8

9 < SYSTEM DESCRITI > Component arts Location FRT WIER AND WASHER SYSTEM INFOID: A B C D E F G H I J K WW M N ALLIA0910ZZ O 1. Front washer motor E226 (view with front bumper cover removed) 2. Combination switch (wiper and washer switch) M28 3. Combination meter M24 4. Front wiper motor E25 5. IDM E/R E17, E18, E BCM M16, M17, M18, M19 (view with instrument panel removed) WW-9

10 FRT WIER AND WASHER SYSTEM < SYSTEM DESCRITI > Component Description INFOID: BCM IDM E/R art Combination switch (Wiper and washer switch) Combination meter Front wiper motor Front washer motor Description Judges the switch status by the combination switch reading function. Requests (with CAN communication) the front wiper relay and the front wiper high relay to IDM E/R. Controls the integrated relay according to the request (with CAN communication) from BCM. erforms the auto stop control of the front wiper. Refer to WW-6, "System Description". Transmits the vehicle speed signal to BCM with CAN communication. Drives windshield wipers in HI or LO mode. Sends wiper stop signal to IDM E/R. umps windshield washer fluid to windshield in wash mode. WW-10

11 < SYSTEM DESCRITI > DIAGNOSIS SYSTEM (BCM) COMM ITEM DIAGNOSIS SYSTEM (BCM) COMM ITEM : CSULT Function (BCM - COMM ITEM) ALICATI ITEM CSULT performs the following functions via CAN communication with BCM. Direct Diagnostic Mode Ecu Identification Self Diagnostic Result Data Monitor Active Test Work support Configuration CAN Diag Support Mntr SYSTEM ALICATI BCM can perform the following functions. The BCM part number is displayed. Displays the diagnosis results judged by BCM. The BCM input/output signals are displayed. Description The signals used to activate each device are forcibly supplied from BCM. Changes the setting for each system function. Enables to read and save the vehicle specification. Enables to write the vehicle specification when replacing BCM. Monitors the reception status of CAN communication viewed from BCM. INFOID: A B C D E F G System Sub System Ecu Identification Self Diagnostic Result Direct Diagnostic Mode Data Monitor Active Test Work support Configuration CAN Diag Support Mntr H I J Door lock DOOR LOCK Rear window defogger REAR DEFOGGER Warning chime BUZZER Interior room lamp timer INT LAM Exterior lamp HEADLAM Wiper and washer WIER Turn signal and hazard warning lamps FLASHER Intelligent Key system INTELLIGENT KEY Combination switch COMB SW BCM BCM Immobilizer IMMU Interior room lamp battery saver BATTERY SAVER Trunk open TRUNK Vehicle security system THEFT ALM RA system RETAINED WR Signal buffer system SIGNAL BUFFER TMS AIR RESSURE MITOR WIER K WW M N O WW-11

12 < SYSTEM DESCRITI > DIAGNOSIS SYSTEM (BCM) WIER : CSULT Function (BCM - WIER) INFOID: DATA MITOR Monitor Item [Unit] USH SW [On/Off] VEH SEED 1 [km/h] FR WIER HI [On/Off] FR WIER LOW [On/Off] FR WASHER SW [On/Off] FR WIER INT [On/Off] FR WIER STO [On/Off] INT VOLUME [1 7] ACTIVE TEST Test Item FR WIER WORK SUORT Description Indicates condition of push button ignition switch Indicates vehicle speed signal received from ABS on CAN communication line Indicates condition of wiper operation of combination switch Indicates front wiper auto stop signal received from IDM E/R on CAN communication line Indicates condition of intermittent wiper operation of combination switch Description This test is able to check front wiper operation [INT/Lo/Hi/Off]. Support Item Setting Description On Front wiper intermittent time linked with vehicle speed and wiper dial position WIER SEED SETTING Off* Front wiper intermittent time linked with wiper dial position * : Initial setting WW-12

13 < SYSTEM DESCRITI > DIAGNOSIS SYSTEM (IDM E/R) Diagnosis Description DIAGNOSIS SYSTEM (IDM E/R) INFOID: A AUTO ACTIVE TEST Description In auto active test mode, the IDM E/R sends a drive signal to the following systems to check their operation. Oil pressure warning lamp Front wiper (LO, HI) arking lamps Side marker lamps License plate lamps Tail lamps Front fog lamps (if equipped) Headlamps (LO, HI) A/C compressor (magnet clutch) Cooling fans Operation rocedure 1. Close the hood and lift the wiper arms from the windshield. (revent windshield damage due to wiper operation) NOTE: When auto active test is performed with hood opened, sprinkle water on windshield beforehand. 2. Turn ignition switch. 3. Turn the ignition switch, and within 20 seconds, press the front door switch LH 10 times. Then turn the ignition switch. CAUTI: Close front door RH. 4. Turn the ignition switch within 10 seconds. After that the horn sounds once and the auto active test starts. 5. The oil pressure warning lamp starts blinking when the auto active test starts. 6. After a series of the following operations is repeated 3 times, auto active test is completed. NOTE: When auto active test mode has to be cancelled halfway through test, turn ignition switch. CAUTI: If auto active test mode cannot be actuated, check door switch system. Refer to DLK-67, "Component Function Check". Do not start the engine. Inspection in Auto Active Test Mode When auto active test mode is actuated, the following 6 steps are repeated 3 times. Operation sequence Inspection Location Operation 1 Oil pressure warning lamp Blinks continuously during operation of auto active test 2 Front wiper LO for 5 seconds HI for 5 seconds 3 arking lamps Side marker lamps License plate lamps Tail lamps Front fog lamps (if equipped) 10 seconds 4 Headlamps LO HI 5 times 5 A/C compressor (magnet clutch) 5 times 6 * Cooling fans MID for 5 seconds HI for 5 seconds *: s duty ratio of 50% for 5 seconds duty ratio of 100% for 5 seconds on the cooling fan control module. B C D E F G H I J K WW M N O WW-13

14 < SYSTEM DESCRITI > Concept of auto active test DIAGNOSIS SYSTEM (IDM E/R) AWMIA1321GB IDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communication. Therefore, the CAN communication line between IDM E/R and BCM is considered normal if the auto active test starts successfully. The auto active test facilitates troubleshooting if any systems controlled by IDM E/R cannot be operated. Diagnosis chart in auto active test mode Symptom Inspection contents ossible cause Any of the following components do not operate arking lamps Side marker lamps License plate lamps Tail lamps Front fog lamps (if equipped) Headlamp (HI, LO) Front wiper erform auto active test. Does the applicable system operate? YES NO BCM signal input circuit Lamp or motor Lamp or motor ground circuit Harness or connector between IDM E/R and applicable system IDM E/R A/C compressor does not operate erform auto active test. Does the magnet clutch operate? YES Combination meter signal input circuit CAN communication signal between combination meter and ECM CAN communication signal between ECM and IDM E/ R NO Magnet clutch Harness or connector between IDM E/R and magnet clutch IDM E/R WW-14

15 < SYSTEM DESCRITI > DIAGNOSIS SYSTEM (IDM E/R) Oil pressure warning lamp does not operate Cooling fan does not operate CSULT Function (IDM E/R) ALICATI ITEM CSULT performs the following functions via CAN communication with IDM E/R. Direct Diagnostic Mode ECU Identification Self Diagnostic Result Data Monitor Active Test CAN Diag Support Mntr ECU IDENTIFICATI The IDM E/R part number is displayed. SELF DIAGNOSTIC RESULT Refer to CS-27, "DTC Index". DATA MITOR Symptom Inspection contents ossible cause erform auto active test. Does the oil pressure warning lamp blink? erform auto active test. Does the cooling fan operate? The IDM E/R part number is displayed. Description The IDM E/R self diagnostic results are displayed. YES NO YES The IDM E/R input/output data is displayed in real time. The IDM E/R activates outputs to test components. NO Harness or connector between IDM E/R and oil pressure switch Oil pressure switch IDM E/R The result of transmit/receive diagnosis of CAN communication is diplayed. CAN communication signal between IDM E/R and BCM CAN communication signal between BCM and combination meter Combination meter ECM signal input circuit CAN communication signal between ECM and IDM E/ R Cooling fan Harness or connector between cooling fan and cooling fan relays Cooling fan relays Harness or connector between IDM E/R and cooling fan relays IDM E/R INFOID: A B C D E F G H I J K WW M N Monitor Item [Unit] Main Signals MOTOR FAN REQ [1/2/3/4] AC COM REQ [On/Off] TAIL&CLR REQ [On/Off] HL LO REQ [On/Off] Description Indicates cooling fan speed signal received from ECM on CAN communication line Indicates A/C compressor request signal received from ECM on CAN communication line Indicates position light request signal received from BCM on CAN communication line Indicates low beam request signal received from BCM on CAN communication line O WW-15

16 < SYSTEM DESCRITI > DIAGNOSIS SYSTEM (IDM E/R) HL HI REQ [On/Off] FR FOG REQ [On/Off] FR WI REQ [Stop/1LOW/Low/Hi] ACTIVE TEST CAN DIAG SUORT MNTR Refer to LAN-12, "CAN Diagnostic Support Monitor". Indicates high beam request signal received from BCM on CAN communication line Indicates front fog light request signal received from BCM on CAN communication line Indicates front wiper request signal received from BCM on CAN communication line WI AUTO STO [STO /ACT ] Indicates condition of front wiper auto stop signal WI ROT [Off/BLOCK] Indicates condition of front wiper fail-safe operation IGN RLY1 -REQ [On/Off] IGN RLY [On/Off] Indicates condition of ignition relay-1 USH SW [On/Off] INTER/N SW [On/Off] ST RLY CT [On/Off] IHBT RLY -REQ [On/Off] ST/INHI RLY [Off/ ST /INHI] DETENT SW [On/Off] DTRL REQ [Off] OIL SW [Open/Close] THFT HRN REQ [On/Off] HORN CHIR [On/Off] HORN FRT WIER Monitor Item [Unit] Test item Main Signals Description Indicates ignition switch signal received from BCM on CAN communication line Indicates condition of push-button ignition switch Indicates condition of CVT shift position Indicates starter relay status signal received from BCM on CAN communication line Indicates starter control relay signal received from BCM on CAN communication line Indicates condition of starter relay and starter control relay Indicates condition of CVT shift selector (park position switch) Indicates daytime light request signal received from BCM on CAN communication line Indicates condition of oil pressure switch Indicates theft warning horn request signal received from BCM on CAN communication line Indicates horn reminder signal received from BCM on CAN communication line This test is able to check horn operation [On]. Description This test is able to check wiper motor operation [Hi/Lo/Off]. MOTOR FAN This test is able to check cooling fan operation [4/3/2/1]. EXTERNAL LAMS This test is able to check external lamp operation [Fog/Hi/Lo/Tail/Off]. WW-16

17 < DTC/CIRCUIT DIAGNOSIS > DTC/CIRCUIT DIAGNOSIS WIER AND WASHER FUSE Description WIER AND WASHER FUSE INFOID: A B Fuse list Unit Location Fuse No. Capacity Front wiper motor IDM E/R A Front washer motor IDM E/R A Diagnosis rocedure 1. CHECK FUSES Check that the following fuses are not blown. INFOID: C D E Unit Location Fuse No. Capacity Front wiper motor IDM E/R A Front washer motor IDM E/R A Is the fuse blown? YES >> Replace the blown fuse after repairing the affected circuit. NO >> The fuse is normal. F G H I J K WW M N O WW-17

18 FRT WIER MOTOR LO CIRCUIT < DTC/CIRCUIT DIAGNOSIS > FRT WIER MOTOR LO CIRCUIT Component Function Check INFOID: CHECK FRT WIER LO OERATI IDM E/R AUTO ACTIVE TEST 1. Start IDM E/R auto active test. Refer to CS-11, "Diagnosis Description". 2. Check that the front wiper operates at the LO operation. CSULT ACTIVE TEST 1. Select "FRT WIER" of IDM E/R active test item. 2. While operating the test item, check front wiper LO operation and. LO : Front wiper LO operation : Stop the front wiper. Does the front wiper operate? YES >> Front wiper motor LO circuit is normal. NO >> Refer to WW-18, "Diagnosis rocedure". Diagnosis rocedure INFOID: Regarding Wiring Diagram information, refer to WW-63, "Wiring Diagram". 1. CHECK FRT WIER MOTOR (LO) OUTUT VOLTAGE CSULT ACTIVE TEST 1. Turn the ignition switch. 2. Disconnect front wiper motor. 3. Turn the ignition switch. 4. Select "FRT WIER" of IDM E/R active test item. 5. While operating the test item, check voltage between IDM E/R harness connector and ground. Terminals Test item (+) (-) Voltage (V) (Approx.) IDM E/R FRT WIER Connector Terminal LO E18 4 Is the measurement normal? YES >> GO TO 2 NO >> Replace IDM E/R. Refer to CS-35, "Removal and Installation". 2. CHECK FRT WIER MOTOR (LO) OEN CIRCUIT ALLIA0922ZZ WW-18

19 < DTC/CIRCUIT DIAGNOSIS > FRT WIER MOTOR LO CIRCUIT 1. Turn the ignition switch. 2. Disconnect IDM E/R. 3. Check continuity between IDM E/R harness connector (A) and front wiper motor harness connector (B). IDM E/R Front wiper motor Connector Terminal Connector Terminal Continuity E18 (A) 4 E25 (B) 1 Yes Does continuity exist? YES >> Replace front wiper motor. Refer to WW-78, "FRT WIER DRIVE ASSEMBLY : Removal and Installation". NO >> Repair or replace harness. ALLIA0816ZZ A B C D E F G H I J K WW M N O WW-19

20 FRT WIER MOTOR HI CIRCUIT < DTC/CIRCUIT DIAGNOSIS > FRT WIER MOTOR HI CIRCUIT Component Function Check INFOID: CHECK FRT WIER HI OERATI IDM E/R AUTO ACTIVE TEST 1. Start IDM E/R auto active test. Refer to CS-11, "Diagnosis Description". 2. Check that the front wiper operates at the HI operation. CSULT ACTIVE TEST 1. Select "FRT WIER" of IDM E/R active test item. 2. While operating the test item, check front wiper HI operation and. HI : Front wiper HI operation : Stop the front wiper. Does the front wiper operate? YES >> The front wiper motor HI circuit is normal. NO >> Refer to WW-20, "Diagnosis rocedure". Diagnosis rocedure INFOID: Regarding Wiring Diagram information, refer to WW-63, "Wiring Diagram". 1. CHECK FRT WIER MOTOR (HI) OUTUT VOLTAGE CSULT ACTIVE TEST 1. Turn the ignition switch. 2. Disconnect front wiper motor. 3. Turn the ignition switch. 4. Select "FRT WIER" of IDM E/R active test item. 5. While operating the test item, check voltage between IDM E/R harness connector and ground. Terminals Test item (+) (-) Voltage (V) IDM E/R (Approx.) FRT WIER Connector Terminal HI E18 5 Is the measurement normal? YES >> GO TO 2 NO >> Replace IDM E/R. Refer to CS-35, "Removal and Installation". 2. CHECK FRT WIER MOTOR (HI) OEN CIRCUIT ALLIA0209ZZ WW-20

21 < DTC/CIRCUIT DIAGNOSIS > FRT WIER MOTOR HI CIRCUIT 1. Turn the ignition switch. 2. Disconnect IDM E/R. 3. Check continuity between IDM E/R harness connector (A) and front wiper motor harness connector (B). IDM E/R Front wiper motor Connector Terminal Connector Terminal Continuity E18 (A) 5 E25 (B) 4 Yes Does continuity exist? YES >> Replace front wiper motor. Refer to WW-78, "FRT WIER DRIVE ASSEMBLY : Removal and Installation". NO >> Repair or replace harness. ALLIA0817ZZ A B C D E F G H I J K WW M N O WW-21

22 FRT WIER AUTO STO SIGNAL CIRCUIT < DTC/CIRCUIT DIAGNOSIS > FRT WIER AUTO STO SIGNAL CIRCUIT Component Function Check INFOID: CHECK FRT WIER (AUTO STO) OERATI CSULT DATA MITOR 1. Select "WI AUTO STO" of IDM E/R DATA MITOR item. 2. Operate the front wiper. 3. With the front wiper operation, check the monitor status. Monitor item Condition Monitor status WI AUTO STO Front wiper motor Stop position STO Except stop position ACT Is the status of item normal? YES >> Auto stop signal circuit is normal. NO >> Refer to WW-22, "Diagnosis rocedure". Diagnosis rocedure INFOID: Regarding Wiring Diagram information, refer to WW-63, "Wiring Diagram". 1. CHECK IDM E/R OUTUT VOLTAGE 1. Turn the ignition switch. 2. Disconnect front wiper motor. 3. Turn the ignition switch. 4. Check voltage between front wiper motor harness connector and ground. Connector Is the measurement normal? YES Terminals (+) (-) Front wiper motor Terminal >> Replace front wiper motor. Refer to WW-78, "FRT WIER DRIVE ASSEMBLY : Removal and Installation". NO >> GO TO 2 2. CHECK FRT WIER MOTOR (AUTO STO) CIRCUIT CTINUITY Voltage (V) (Approx.) E Turn the ignition switch. 2. Disconnect IDM E/R connector E Check continuity between IDM E/R harness connector and front wiper motor harness connector. IDM E/R Front wiper motor Continuity Connector Terminal Connector Terminal E18 16 E25 5 Yes 4. Check continuity between IDM E/R harness connector and ground. IDM E/R Continuity Connector Terminal E18 16 No WW-22

23 FRT WIER AUTO STO SIGNAL CIRCUIT < DTC/CIRCUIT DIAGNOSIS > Is the inspection result normal? YES >> Replace IDM E/R. Refer to CS-35, "Removal and Installation". NO >> Repair or replace harness. A B C D E F G H I J K WW M N O WW-23

24 FRT WIER MOTOR GROUND CIRCUIT < DTC/CIRCUIT DIAGNOSIS > FRT WIER MOTOR GROUND CIRCUIT Diagnosis rocedure INFOID: Regarding Wiring Diagram information, refer to WW-63, "Wiring Diagram". 1.CHECK FRT WIER MOTOR (GND) OEN CIRCUIT 1. Turn the ignition switch. 2. Disconnect front wiper motor. 3. Check continuity between front wiper motor harness connector and ground. Front wiper motor Continuity Connector Terminal E25 2 Yes Does continuity exist? YES >> Front wiper motor ground circuit is normal. NO >> Repair or replace harness. ALLIA0819ZZ WW-24

25 < DTC/CIRCUIT DIAGNOSIS > WASHER SWITCH Description WASHER SWITCH INFOID: A Washer switch is integrated with combination switch (wiper and washer switch). Combination switch (wiper and washer switch) supplies ground and fuse # 38 from the IEM E/R supplies power for the front washer motor to operate. B C D E F Component Inspection Regarding Wiring Diagram information, refer to WW-63, "Wiring Diagram". 1. CHECK WASHER SWITCH 1. Turn the ignition switch. 2. Disconnect combination switch (wiper and washer switch). 3. Check continuity between the combination switch (wiper and washer switch) terminals. A: Terminal 1 B: Terminal 6 ABLIA2945GB INFOID: G H I J K WW ALLIA0546GB M Combination switch (wiper and washer switch) Condition Continuity Terminal 1 6 Washer switch Yes Washer switch No Is the measurement normal? YES >> Washer switch is normal. NO >> Replace combination switch (wiper and washer switch). Refer to WW-85, "Removal and Installation". N O WW-25

26 < DTC/CIRCUIT DIAGNOSIS > WASHER MOTOR CIRCUIT Diagnosis rocedure WASHER MOTOR CIRCUIT INFOID: Regarding Wiring Diagram information, refer to WW-63, "Wiring Diagram". 1. CHECK FRT WASHER MOTOR FUSE 1. Turn the ignition switch. 2. Check that the following fuse is not blown. Unit Location Fuse No. Capacity Front washer motor IDM E/R 38 10A Is the fuse blown? YES >> Replace the fuse after repairing the affected circuit. NO >> GO TO 2 2. CHECK FRT WASHER MOTOR OWER SULY 1. Disconnect front washer motor. 2. Turn ignition switch. 3. Check voltage between front washer motor harness connector and ground. Connector Terminals (+) (-) Front washer motor Terminal Voltage (Approx.) E226 1 Is the measurement value normal? YES >> GO TO 3. NO >> GO TO CHECK FRT WASHER MOTOR CIRCUIT CTINUITY 1. Turn the ignition switch. 2. Disconnect combination switch (wiper and washer switch). 3. Check continuity between combination switch (wiper and washer switch) harness connector and front washer motor. Combination switch (wiper and washer switch) Front washer motor Connector Terminal Connector Terminal Continuity M28 1 E226 2 Yes Is the measurement normal? YES >> GO TO 4 NO >> Repair or replace harness. 4. CHECK WIER AND WASHER SWITCH GROUND CIRCUIT Check continuity between combination switch (wiper and washer switch) harness connector and ground. Combination switch (wiper and washer switch) Continuity Connector Terminal M28 6 Yes Does continuity exist? WW-26

27 < DTC/CIRCUIT DIAGNOSIS > WASHER MOTOR CIRCUIT YES >> GO TO 6 NO >> Repair or replace harness. 5. CHECK FRT WASHER MOTOR OEN CIRCUIT 1. Turn the ignition switch. 2. Disconnect IDM E/R. 3. Check continuity between IDM E/R harness connector and front washer motor. IDM E/R Front washer motor Connector Terminal Connector Terminal Does continuity exist? YES >> Replace IDM E/R. Refer to CS-35, "Removal and Installation". NO >> Repair or replace harness. 6. CHECK WIER AND WASHER SWITCH Continuity E E226 1 Yes Check wiper and washer switch. Refer to WW-25, "Component Inspection". Is the inspection result normal? YES >> Replace front washer motor. Refer to WW-82, "FRT WASHER UM : Removal and Installation". NO >> Replace wiper and washer switch. Refer to WW-85, "Removal and Installation". A B C D E F G H I J K WW M N O WW-27

28 BCM (BODY CTROL MODULE) < ECU DIAGNOSIS INFORMATI > ECU DIAGNOSIS INFORMATI BCM (BODY CTROL MODULE) Reference Value INFOID: NOTE: The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information. Activate and display TMS transmitter IDs Display tire pressure reported by the TMS transmitter Read TMS DTCs Register TMS transmitter IDs Check Intelligent Key relative signal strength Confirm vehicle Intelligent Key antenna signal strength VALUES THE DIAGNOSIS TOOL Monitor Item Condition Value/Status FR WIER HI Other than front wiper switch HI Front wiper switch HI FR WIER LOW Other than front wiper switch LO Front wiper switch LO FR WASHER SW Front washer switch Front washer switch FR WIER INT Other than front wiper switch INT Front wiper switch INT FR WIER STO Front wiper is not in STO position Front wiper is in STO position INT VOLUME Wiper intermittent dial is in a dial position 1-7 Wiper intermittent dial position TURN SIGNAL R TURN SIGNAL L TAIL LAM SW HI BEAM SW HEAD LAM SW 1 HEAD LAM SW 2 ASSING SW AUTO LIGHT SW FR FOG SW DOOR SW-DR Other than turn signal switch RH Turn signal switch RH Other than turn signal switch LH Turn signal switch LH Other than lighting switch 1ST and 2ND Lighting switch 1ST or 2ND Other than lighting switch HI Lighting switch HI Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch ASS Lighting switch ASS Other than lighting switch AUTO Lighting switch AUTO Front fog lamp switch Front fog lamp switch Driver door closed Driver door opened WW-28

29 < ECU DIAGNOSIS INFORMATI > BCM (BODY CTROL MODULE) DOOR SW-AS DOOR SW-RR DOOR SW-RL CDL LOCK SW CDL UNLOCK SW KEY CYL LK-SW KEY CYL UN-SW HAZARD SW assenger door closed assenger door opened Rear door RH closed Rear door RH opened Rear door LH closed Rear door LH opened Other than power door lock switch LOCK ower door lock switch LOCK Other than power door lock switch UNLOCK ower door lock switch UNLOCK Other than driver door key cylinder LOCK position Driver door key cylinder LOCK position Other than driver door key cylinder UNLOCK position Driver door key cylinder UNLOCK position When hazard switch is not pressed When hazard switch is pressed REAR DEF SW When rear window defogger switch is pressed TR CANCEL SW TR/BD OEN SW TRNK/HAT MNTR RKE-LOCK RKE-UNLOCK RKE-TR/BD RKE-ANIC Monitor Item Condition Value/Status RKE-/W OEN RKE-MODE CHG OTICAL SENSOR REQ SW -DR REQ SW -AS REQ SW -RL Trunk lid opener cancel switch Trunk lid opener cancel switch Trunk lid opener switch While the trunk lid opener switch is turned Trunk lid closed Trunk lid opened When LOCK button of Intelligent Key is not pressed When LOCK button of Intelligent Key is pressed When UNLOCK button of Intelligent Key is not pressed When UNLOCK button of Intelligent Key is pressed When TRUNK OEN button of Intelligent Key is not pressed When TRUNK OEN button of Intelligent Key is pressed When ANIC button of Intelligent Key is not pressed When ANIC button of Intelligent Key is pressed When UNLOCK button of Intelligent Key is not pressed and held When UNLOCK button of Intelligent Key is pressed and held When LOCK/UNLOCK button of Intelligent Key is not pressed and held simultaneously When LOCK/UNLOCK button of Intelligent Key is pressed and held simultaneously When outside of the vehicle is bright When outside of the vehicle is dark When front door request switch is not pressed (driver side) When front door request switch is pressed (driver side) When front door request switch is not pressed (passenger side) When front door request switch is pressed (passenger side) When rear door request switch is not pressed (driver side) When rear door request switch is pressed (driver side) Close to 5 V Close to 0 V A B C D E F G H I J K WW M N O WW-29

30 BCM (BODY CTROL MODULE) < ECU DIAGNOSIS INFORMATI > Monitor Item Condition Value/Status REQ SW -RR When rear door request switch is not pressed (passenger side) When rear door request switch is pressed (passenger side) REQ SW -BD/TR When trunk request switch is not pressed When trunk request switch is pressed USH SW When engine switch (push switch) is not pressed When engine switch (push switch) is pressed IGN RLY2 -F/B Ignition switch or ACC Ignition switch ACC RLY -F/B Ignition switch Ignition switch ACC or BRAKE SW 1 When the brake pedal is not depressed When the brake pedal is depressed DETE/CANCL SW When selector lever is in position When selector lever is in any position other than SFT N/N SW When selector lever is in any position other than or N When selector lever is in or N position UNLK SEN -DR Driver door UNLOCK status Driver door LOCK status USH SW -IDM When engine switch (push switch) is not pressed When engine switch (push switch) is pressed IGN RLY1 -F/B Ignition switch or ACC Ignition switch DETE SW -IDM When selector lever is in position When selector lever is in any position other than SFT N -IDM When selector lever is in any position other than or N When selector lever is in or N position SFT -MET When selector lever is in any position other than When selector lever is in position SFT N -MET When selector lever is in any position other than N When selector lever is in N position Engine stopped STO ENGINE STATE While the engine stalls STALL At engine cranking CRANK Engine running RUN VEH SEED 1 While driving Equivalent to speedometer reading VEH SEED 2 While driving Equivalent to speedometer reading Driver door LOCK status LOCK DOOR STAT-DR Wait with selective UNLOCK operation (5 seconds) READY Driver door UNLOCK status UNLK assenger door LOCK status LOCK DOOR STAT-AS Wait with selective UNLOCK operation (5 seconds) READY assenger door UNLOCK status UNLK ID OK FLAG Ignition switch ACC or RESET Ignition switch SET WW-30

31 < ECU DIAGNOSIS INFORMATI > BCM (BODY CTROL MODULE) RMT ENG STRT KEY SW -SLOT When the engine start is prohibited When the engine start is permitted When Intelligent Key is not inserted into key slot When Intelligent Key is inserted into key slot RESET RKE OE COUN1 During the operation of Intelligent Key Operation frequency of Intelligent Key CFRM ID ALL CFIRM ID4 CFIRM ID3 CFIRM ID2 CFIRM ID1 T 4 T 3 T 2 T 1 Monitor Item Condition Value/Status AIR RESS FL AIR RESS FR AIR RESS RR AIR RESS RL ID REGST FL1 ID REGST FR1 ID REGST RR1 ID REGST RL1 The key ID that the key slot receives does not accord with any key ID registered to BCM. The key ID that the key slot receives accords with any key ID registered to BCM. The key ID that the key slot receives does not accord with the fourth key ID registered to BCM. The key ID that the key slot receives accords with the fourth key ID registered to BCM. The key ID that the key slot receives does not accord with the third key ID registered to BCM. The key ID that the key slot receives accords with the third key ID registered to BCM. The key ID that the key slot receives does not accord with the second key ID registered to BCM. The key ID that the key slot receives accords with the second key ID registered to BCM. The key ID that the key slot receives does not accord with the first key ID registered to BCM. The key ID that the key slot receives accords with the first key ID registered to BCM. The ID of fourth key is not registered to BCM The ID of fourth key is registered to BCM The ID of third key is not registered to BCM The ID of third key is registered to BCM The ID of second key is not registered to BCM The ID of second key is registered to BCM The ID of first key is not registered to BCM The ID of first key is registered to BCM Ignition switch (only when the signal from the transmitter is received) Ignition switch (only when the signal from the transmitter is received) Ignition switch (only when the signal from the transmitter is received) Ignition switch (only when the signal from the transmitter is received) When ID of front LH tire transmitter is registered When ID of front LH tire transmitter is not registered When ID of front RH tire transmitter is registered When ID of front RH tire transmitter is not registered When ID of rear RH tire transmitter is registered When ID of rear RH tire transmitter is not registered When ID of rear LH tire transmitter is registered When ID of rear LH tire transmitter is not registered SET YET DE YET DE YET DE YET DE YET DE YET DE YET DE YET DE YET DE Air pressure of front LH tire Air pressure of front RH tire Air pressure of rear RH tire Air pressure of rear LH tire DE YET DE YET DE YET DE YET A B C D E F G H I J K WW M N O WW-31

32 BCM (BODY CTROL MODULE) < ECU DIAGNOSIS INFORMATI > WARNING LAM BUZZER Monitor Item Condition Value/Status Tire pressure indicator Tire pressure indicator Tire pressure warning alarm is not sounding Tire pressure warning alarm is sounding WW-32

33 < ECU DIAGNOSIS INFORMATI > Terminal Layout BCM (BODY CTROL MODULE) INFOID: A B C D E F G H I J K WW M N O hysical Values ALMIA0127ZZ INFOID: WW-33

34 BCM (BODY CTROL MODULE) < ECU DIAGNOSIS INFORMATI > Terminal No. (Wire color) (+) (-) 1 (W/B) 2 (R/Y) 3 (L/W) 4 (/W) 5 (G) 7 (R/W) 8 (V) 9 (L) 10 (G) 11 (Y/R) 13 (B) 14 (GR/ W) Description Signal name Input/ Condition Battery power supply Input Ignition switch Battery power supply output Ignition power supply output Interior room lamp power supply Front door RH UN- LOCK Ignition switch Ignition switch After passing the interior room lamp battery saver operation time Any other time after passing the interior room lamp battery saver operation time Front door RH Step lamp Step lamp All doors LOCK All doors Front door LH UN- LOCK Rear door RH and rear door LH UN- LOCK Front door LH Rear door RH and rear door LH UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated) LOCK (actuator is activated) Other than LOCK (actuator is not activated) UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated) UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated) Battery power supply Input Ignition switch Ignition switch Engine switch (push switch) illumination ground Input Tail lamp Value (Approx.) NOTE: When the illumination brightening/dimming level is in the neutral position JSNIA0010GB 15 (Y/L) ACC indicator lamp Ignition switch ACC or WW-34

35 < ECU DIAGNOSIS INFORMATI > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A Turn signal switch B 17 (G/B) Turn signal (RH) Ignition switch Turn signal switch RH C 6.5 V KID0926E D Turn signal switch E 18 (G/Y) Turn signal (LH) Ignition switch Turn signal switch LH F 6.5 V KID0926E G 19 (Y) Room lamp timer control Interior room lamp H 21 (/B) Optical sensor signal Input Ignition switch When outside of the vehicle is bright When outside of the vehicle is dark Close to 5V Close to I 24 (R/W) Stop lamp switch 1 Input J 26 (O/L) Stop lamp switch 2 Input Stop lamp switch (brake pedal is released) (brake pedal is depressed) K WW 27 (O) Front door lock assembly LH (unlock sensor) Input Front door LH LOCK status M 11.8V JMIA0011GB N UNLOCK status 29 (Y) Key slot switch Input When Intelligent Key is inserted into key slot When Intelligent Key is not inserted into key slot O 31 (G) Rear window defogger feedback signal Input Rear window defogger switch WW-35

36 BCM (BODY CTROL MODULE) < ECU DIAGNOSIS INFORMATI > Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) 32 (R/B) Front door RH switch Input Front door RH switch (when front door RH closes) 11.8 V JMIA0011GB (when front door RH opens) 37 (O) Trunk lid opener cancel switch Input Trunk lid opener cancel switch CANCEL 1.1V JMIA0012GB 38 (GR/ W) Rear window defogger signal Input Rear window defogger switch 5V 40 (Y/G) ower window serial link Input/ Ignition switch 41 (W) 42 (R) 45 () 46 (V/W) Engine switch (push switch) illumination LOCK indicator lamp Receiver & sensor ground Receiver & sensor power supply output Ignition switch or ACC Engine switch (push switch) illumination LOCK indicator lamp 5.5V Input Ignition switch Ignition switch ACC or V JMIA0013GB WW-36

37 < ECU DIAGNOSIS INFORMATI > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A B Standby state C 47 (G/O) Tire pressure receiver signal Input/ Ignition switch OCC3881D D E When receiving the signal from the transmitter F OCC3880D 48 (R/G) Selector lever transmission range switch signal Input Selector lever or N position 12. Except and N positions G H I 49 (L/O) Security indicator signal Security indicator Blinking J 11.3V JMIA0014GB K All switch 50 (LG/ B) Combination switch OUTUT 5 Input Combination switch (Wiper intermittent dial 4) Lighting switch 1ST Lighting switch high-beam Lighting switch 2ND WW M Turn signal switch RH 10.7V JMIA0031GB N All switch (Wiper intermittent dial 4) Front wiper switch HI (Wiper intermittent dial 4) O 51 (L/W) Combination switch OUTUT 1 Input Combination switch Any of the conditions below with all switch Wiper intermittent dial 1 WIper intermittent dial 2 Wiper intermittent dial 3 Wiper intermittent dial 6 Wiper intermittent dial V JMIA0032GB WW-37

38 BCM (BODY CTROL MODULE) < ECU DIAGNOSIS INFORMATI > Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) All switch (Wiper intermittent dial 4) Front washer switch (Wiper intermittent dial 4) 52 (G/B) Combination switch OUTUT 2 Input Combination switch Any of the conditions below with all switch Wiper intermittent dial 1 WIper intermittent dial 5 Wiper intermittent dial V JMIA0033GB All switch Front wiper switch INT 53 (LG/ R) Combination switch OUTUT 3 Input Combination switch (Wiper intermittent dial 4) Front wiper switch LO Lighting switch AUTO 10.7V JMIA0034GB All switch Front fog lamp switch 54 (G/Y) Combination switch OUTUT 4 Input Combination switch (Wiper intermittent dial 4) Lighting switch 2ND Lighting switch flash-topass Turn signal switch LH 10.7V JMIA0035GB 57 (W) Tire pressure warning check switch Input 5V 58 (SB) Front door LH switch Input Front door LH switch (front door LH CLOSE) 11.8V JMIA0011GB (front door LH OEN) 59 (G/R) Rear window defogger relay Rear window defogger Active Not activated WW-38

39 < ECU DIAGNOSIS INFORMATI > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A B When Intelligent Key is in the passenger compartment C 60 (B/R) Front console antenna 2 (-) Ignition switch JMKIA0062GB D When Intelligent Key is not in the passenger compartment E F JMKIA0063GB G When Intelligent Key is in the passenger compartment H JMKIA0062GB I 61 (W/R) Center console antenna 2 (+) Ignition switch J When Intelligent Key is not in the passenger compartment K JMKIA0063GB WW M When Intelligent Key is in the antenna detection area N 62 (V) Front outside handle RH antenna (-) When the front door RH request switch is operated with ignition switch JMKIA0062GB O When Intelligent Key is not in the antenna detection area JMKIA0063GB WW-39

40 BCM (BODY CTROL MODULE) < ECU DIAGNOSIS INFORMATI > Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) When Intelligent Key is in the antenna detection area 63 () Front outside handle RH antenna (+) When the front door RH request switch is operated with ignition switch JMKIA0062GB When Intelligent Key is not in the antenna detection area JMKIA0063GB When Intelligent Key is in the antenna detection area 64 (V) Front outside handle LH antenna (-) When the front door LH request switch is operated with ignition switch JMKIA0062GB When Intelligent Key is not in the antenna detection area JMKIA0063GB When Intelligent Key is in the antenna detection area 65 () Front outside handle LH antenna (+) When the front door LH request switch is operated with ignition switch JMKIA0062GB When Intelligent Key is not in the antenna detection area JMKIA0063GB WW-40

41 < ECU DIAGNOSIS INFORMATI > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A 68 (G/O) NATS antenna amp (built in key slot) Input/ During waiting Ignition switch is pressed while inserting the Intelligent Key into the key slot. Just after pressing ignition switch. ointer of tester should move. B 69 (O) NATS antenna amp (built in key slot) Input/ During waiting Ignition switch is pressed while inserting the Intelligent Key into the key slot. Just after pressing ignition switch. ointer of tester should move. C 70 (R/B) Ignition relay-2 control Ignition switch or ACC D E During waiting F JMKIA0064GB 71 (L/O) Remote keyless entry receiver signal Input/ G When operating either button on Intelligent Key H JMKIA0065GB I J All switch (Wiper intermittent dial 4) K 1.4V JMIA0041GB WW M 75 (R/Y) Combination switch INUT 5 Combination switch Front fog lamp switch (Wiper intermittent dial 4) N 1.3V JMIA0037GB O Any of the conditions below with all switch Wiper intermittent dial 1 Wiper intermittent dial 2 Wiper intermittent dial 6 Wiper intermittent dial 7 1.3V JMIA0040GB WW-41

42 BCM (BODY CTROL MODULE) < ECU DIAGNOSIS INFORMATI > Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) All switch (Wiper intermittent dial 4) 1.4V JMIA0041GB Lighting switch high-beam (Wiper intermittent dial 4) 76 (R/G) Combination switch INUT 3 Combination switch 1.3V JMIA0036GB Lighting switch 2ND (Wiper intermittent dial 4) 1.3V JMIA0037GB Any of the conditions below with all switch Wiper intermittent dial 1 Wiper intermittent dial 2 Wiper intermittent dial 3 1.3V JMIA0040GB 78 () CAN-L Input/ 79 (L) CAN-H Input/ 80 (R/L) Key slot illumination Key slot illumination Blinking 6.5V JMIA0015GB 81 (LG) indicator lamp Ignition switch or ACC WW-42

43 < ECU DIAGNOSIS INFORMATI > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) 83 (L) 84 (Y/R) 87 (G/B) ACC relay control Ignition switch ACC or CVT shift selector Description Signal name Selector lever position switch Input/ Input Selector lever Condition position Any position other than (pressed) Value (Approx.) A B C D 88 (R) Front door RH request switch Input Front door RH request switch (not pressed) E F (pressed) 1. JMIA0016GB G 89 (R) Front door LH request switch Input Front door LH request switch (not pressed) H I 90 (Y) Blower fan motor relay control Ignition switch or ACC 1. JMIA0016GB J 91 (L/R) Remote keyless entry receiver power supply Ignition switch K WW M N O WW-43