Thank You For Choosing. INSTALLATION INSTRUCTIONS Power Steering Kit for Polaris Ranger 570 B C. Need help with your installation?

Transcription

1 2753 Michigan Road Madison, Indiana INSTALLATION INSTRUCTIONS Power Steering Kit for Polaris Ranger 570 Item A B C D E F G Description Motor Mount Upper Shaft Lower Shaft ECU Mount Connectors Kit Mounting Flange Clamping Bracket B C E A F G D (Kit contents continue on following pages) Need help with your installation? sales@superatv.com :00am - 9:00pm EST M-Th 8:00am - 7:00pm EST Friday 9:00am - 2:00pm EST Saturday Read instructions and view illustrations before beginning. Thank You For Choosing 2016 SuperATV.com. All Rights Reserved. IN-PS /13/2016

2 (Kit contents continued) *Connections - Before installing, ensure that all Gaskets in electrical connections are properly seated. - If Gaskets are not seated use a Flathead Screwdriver to seat. Item J K L Description ECU Motor Wiring Harness J* Seat E K* L* Seat Push in......seat Power Steering will provide multiple improvements to your machine. After installation, it is highly recommend to take time and learn your machines new handling characteristics and feel. Key Recommendations: 1. Power Steering Benefits will be noticed as soon as machine is moving. 2. Check steering sensitivity at multiple speeds to best understand new handling characteristics and feel. 3. Without Throttle input, turning Steering Wheel back and forth unnecessarily is not recommended. This action is very hard on steering components, Tie Rod Ends, and Power Steering unit. Like all SuperATV products, Power Steering kits were designed with riders in mind. IN-PS

3 (Kit contents continued) 2x M6-1.0 x 16mm Lg. HHCS -includes washers (not shown) 5x M Nylock Nut 2x M x 40mm Lg. FHCS 1x M6-1.0 Nylock Nut 1x M x 30mm Lg. FHCS 2x Spacer 1x M6-1.0 x 30mm Lg. FHCS 5x M x 20mm Lg. FHCS Removal: Keep all components removed from machine. remove Lower Dash (Driver Side) (removal illustrations continue on following pages) IN-PS

4 remove Steering Wheel remove Bearings and Bushings remove Throttle Pedal IN-PS

5 remove Shock hardware remove Tilter remove Bearings and Bushings remove Tilter hardware IN-PS

6 remove Steering Shaft from Rack and Pinion (viewed from Passenger Side) remove Steering Shaft (pull up and through Firewall) IN-PS

7 220 Motor to Rack and Pinion 400 Motor to Rack and Pinion IN-PS

8 - Install Motor (K) to Motor Mount (A) with hardware shown. 3x M8 x 20mm A K IN-PS

9 - Install Lower Shaft (C) to Rack and Pinion; secure with provided hardware. C supplied hardware Rack and Pinion (viewed from Passenger Side) - Install Upper Shaft (B) to Tilter. reuse stock Bearings and Bushings B Tilter IN-PS

10 - Install Tilter - Upper Shaft (B) with stock hardware. B reinstall Tilter with stock hardware IN-PS

11 - Install Motor (K) onto Lower Shaft (C); secure with provided hardware. - Secure Motor Mount (A) to Frame with hardware shown. M8 x 30mm M8 Nut Frame A K C supplied hardware IN-PS

12 M8 hardware Spacers F G M6 hardware - Secure Upper Shaft (B) to Motor (K) with provided hardware. - Install Mounting Flange (F) to Motor Mount (A) with hardware shown. - Install Clamping Bracket (G) to Mounting Flange (F) with Spacers and hardware shown. Clamping Bracket (G) installs to outside of Frame. Parts Reference Item A B F G K Description Motor Mount Upper Shaft Mounting Flange Clamping Bracket Motor M8 hardware M6 x 30mm M6 Nut M8 x 40mm G Frame B 2 each supplied hardware K M8 Nut F 2 each A M8 x 20mm M8 Nut IN-PS

13 - Place ECU (J) on top of Frame as shown in illustration below. - Install ECU Mount (D) to ECU (J) with hardware shown. (Front) (Passenger Side) (Driver Side) J D M6-1.0 x 16mm Lg. HHCS -includes washers (not shown) on top of Frame J ECU Mount (D) through here - Reinstall Steering Wheel and Throttle Pedal with stock hardware. - Ensure that no interference can occur and tighten all hardware completely. - Connect Motor (K) wiring to ECU (J). - See last page and make connections. - Reinstall Lower Dash. IN-PS

14 Wiring Details: - Except for Accessory Lead, Terminal Block does not come wired from factory. - If an accessory is factory installed (Winch, Lights, etc.) then Terminal Block may be wired. Connect Black (-) and Red (+) wires from Wire Harness (L) to Terminal Block. Option A: - Installer can run #8 or larger negative and positive wires from Battery to Terminal Block and connect. - Connect Black (-) and Red (+) wires from Wire Harness (L) to Terminal Block. Option B: - Route Black (-) and Red (+) wires from Wire Harness (L) to Battery and connect. (Driver Side) Terminal Block Make connection with provided Connectors Kit (E) if applicable. E Wire Harness (L) White Wire Black Wire (-) Red Wire (+) IN-PS

15 Wiring Details continued Power Connections: (See previous page also) Black Wire to Battery (-) Red Wire to Battery (+) When activated, LED Diagnostic Light will flash once for about 1 second before turning off indicating proper function. If different patterns occur, contact SuperATV. LED Diagnostic Light Secure in a visible location White Wire to switched 12V source (key-on) Wire Harness (L) Plug into ECU (J) ECU (J) Reference Plug Function A Torque Sensor B Switched 12V Source C D Power Motor A B C D IN-PS

16 Liability Statement SuperATV s products are designed to best fit user s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV and is not recommended. SuperATV s products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV to verify that they will work together. Although SuperATV has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product s ability to protect user from severe injury or death. SuperATV urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing SuperATV products, user agrees that should damages occur, SuperATV will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. SuperATV will warranty only parts provided by SuperATV. Any damage or problems with OEM housings, bearings, seals, or other manufacturers products will not be covered by SuperATV. SuperATV parts and products are not warrantied if item was not installed properly, misused, or modified. Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you. The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV harmless from any violation thereof. IN-PS