EFIE Wideband O2 (Electronic Fuel Injector Enhancer) Installation & Operating Instructions.
|
|
- Priscilla Green
- 5 years ago
- Views:
Transcription
1 EFIE Wideband O2 (Electronic Fuel Injector Enhancer) Installation & Operating Instructions. The EFIE is not intended to be a fuel saver by itself. The EFIE is designed to be used in conjunction with fuel saver devices, such as a hydrogen gas electrolyzer, a fuel vapor production unit, or other devices that increase the efficiency of the burn. EFIE Wideband O2. This EFIE will work with all wideband zirconia type of oxygen sensors (Not AFR). All oxygen sensors that were developed before catalytic converter need to own dedicated EFIE device. Oxygen sensors that were developed after catalytic converter do not need EFIE devices, because they are only used by ECU to monitor converter fuel efficiency. 1. Features. 1. Soft Start Feature slowly increases the voltages offset when powered ON (For example: O2 sensor warm up delay). 2. Option to disable Soft Start Feature. 3. LED light indicates when the power is ON. 4. Additional Terminal Block makes testing the voltages (offset, input and output) simple. 5. Special circuit design eliminates variance of actual voltage output, input and offset when using voltmeter. 6. Adjustable offset. Range is adjustable from 0v to 2.5V and from 0v to 500mV (0.5V). 7. Normal connection from O2/MAP/MAF sensors to the ECU (vehicle computer) when power OFF. 8. Fine tune with a 24 turn potentiometer. 1
2 9. Low current consumption: 25mA (0.025A). 10. Low temperature sensitivity +/- 2mV (0.002V). 11. Operating temperature: -35F to 220F (-37C to 105C). 12. Small size: 2" x 1.5" x 0.6 (51mm x 38mm x 15mm). 2. Installation. Installation is the easiest if you have a Haynes, Clymer or Chilton manual for your car. If not, then you can buy a wiring diagram from sites like Or, go to the following URL: Then: 1. Locate your car s year, make and model. 2. Select: Repair Info at the left side of the screen. 3. Select: Vehicle Repair Guides, Chassis Electrical, Wiring Diagrams. If you have a problem with getting the wiring diagram, you can attempt to identify the wires yourself. Wires of O2 Sensor signal out (Vs) black grey red black sign in (Ip) red red black blue sign in (Vs/Ip) yellow green yellow yellow heater + grey light blue grey grey heater - white red white white Rcal (optional) green green green green Rcal = laser trimmed calibration resistor only for 6-wire wideband sensors. Even if you have found all the color marks, it is recommended to read the technique written below. 2
3 = 2.1 = Note: Instead of taking a chance by stripping insulation, you can take two sewing needles or poster pins. Turn ignition OFF. Pierce isolation so that the needles are touching the wire inside the isolation. Now you can measure the voltage. Attach a minus of multi-meter to a minus of the car Battery. Turn multi-meter to DC mode Turn ignition ON. Don t disconnect the Oxygen sensor plug. Wait for 3-5 minutes. Use multi-meter to probe the voltage between a minus of the car battery and five wires of a Wideband O2 Sensor. If you see changes from 0.3 to 4.9 Volt between minus of car battery and one of the five wires of Wideband O2 sensor then that wire is a signal wire of the Wideband O2 sensor. 3
4 3. Locate 12 Volt power and Ground. If you now install this EFIE, then you should already have installed a fuel saver device. Therefore, I think that you have already found the +12 volt and the ground (minus). The +12 volt is the best way for transferring from the fuel saver device. The reason which is necessary to connect +12 Volt of EFIE to the +12 Volt of the fuel saver device is very simple: when you turn ON fuel saver device then simultaneously you turn ON EFIE and when you turn OFF the fuel saver device then simultaneously you turn OFF the EFIE. The EFIE works only when the fuel saver device works. In any case you can use an ignition switched power source +12 Volt to the EFIE. The EFIE will shut OFF when you shut OFF ignition key. If you previously have not established the fuel saver device, these resources can help: Note: O2 sensor heater wire can not be used because in some cases ECU (vehicle computer) will cut the power to the O2 sensor during the trip. The ground can be the vehicle body (chassis ground), engine block or ground from another device. Do not use oxygen sensor as a ground. Test the resistance (turn multi-meter to Resistance mode) between ground wire, which you have found and battery negative terminal. If it is < 10 ohm you can use it. 4
5 Turn multi-meter to Resistance mode 4. Placing EFIE. Before placing EFIE in the car place jumpers as shown in picture 1. Installation of jumpers should be carried out only when the power is OFF. Picture 1 5
6 The time of delay is approximately 5-6 minutes (Soft Start Feature slowly increases the voltage offset when powered ON, to allow the computer to have time to adjust for the changes.) The best place for the installation of the EFIE is a place where the EFIE will be warm, dry and accessible to adjustment. As a last resort, the EFIE can be placed under the hood, but you should take care of water resistance and humidity resistance. We recommend that is better to be installed under a dash. The EFIE can be attached in the chosen place with Velcro. Due to this, it is necessary for you to pick up a suitable plastic box and attach the EFIE inside with the Velcro. 5. Connect EFIE wires. Picture 2 Note: During connection and the lining of wires execute some simple rules: while lining the wires try not to lay wires near to details of the car which will be hot during the working of the car. At connection of wires don t use crimp connectors. Solder wires, and then seal them with silicone, shrink-wrap or with liquid tape. 6
7 Turn ignition OFF. Connect wire from the car ground (read section 3) to the EFIE connector (3) shown in Picture 2. Connect +12 Volt wire (read section 3) to the EFIE connector (4) shown in Picture 2. Cut the Oxygen Sensor signal wire on the car side of the connector. Connect wire from Oxygen Sensor side to EFIE connector (2) and wire from ECU side to EFIE connector (1). Remember, to solder wires and seal them for prevention of corrosion. 6. Operation The time of delay is approximately 5-6 minutes (Soft Start Feature slowly increases the voltage offset when powered ON to allow the computer time to adjust for the changes.) Now look at the picture below. We see that after 5 minutes, the voltage is equal 189 millivolt, and after 6 minutes 193 millivolt. The final voltage should be 200 millivolt. As shown by the graph, during 5-6 minutes the voltage of Soft Start Feature will reach a point in the 95% threshold. The last 5% threshold will be reached in the following of 5-6 minutes. (The data on each device can differ a little). Soft Start Feature mv :00 1:00 2:00 3:00 4:00 5:00 6:00 7:00 8:00 9:00 10:00 11:00 Minutes Adjustments should only be made when the EFIE is powered ON and the engine is warm and running. Do not make any adjustments without the use of a volt-meter. Touch your meter leads to the In test pin (5), Out test pin (6), 7
8 Reference Voltage test pin (7) on the EFIE to read the voltage while adjusting. Picture 3 Note: For the Ground you can use a screw number 3 in Picture 2. Variable resistor adjustment range is approximately 24 turns and from about 0 to 500 millivolts (0.5 Volts). Step of adjustment up to 1 millivolt. It is not necessary to wait time between adjustments. Start by turning the adjustment screws counterclockwise (Leaner) to increase the voltage offset to the computer. Turning the screws clockwise (Richen) will decrease the voltage offset. Remember that it is the subtractor, as increase of the voltage offset causes reduction of output voltage from EFIE and on the contrary. Be careful not to over turn as they may be damaged, however, they do have a built in clutch and are quite forgiving. Also remember about Soft Start. When you turn ON the EFIE it is necessary to wait for 5-6 minutes. During this time, we know that a reference voltage will reach 95 %. The others 5 % will take 5-6 minutes more, but we do not need to wait during this time and we can simply remove a jumper (shown by red color in the picture below). Thus, it is not necessary to switch OFF the EFIE. This jumper disables the Soft Start Feature and the voltage reaches 100% instantly. Now it is possible to make an adjustment. After performance of adjustment it is necessary to return a jumper in an initial place. 8
9 If you notice any performance issues or your "check engine" light comes on, you've likely set the offset too high. You will need to lower the offset (turn clockwise) and reset the vehicles computer. This can usually be done by disconnecting the battery for a few minutes. Please refer to your vehicle owner s manual for the recommended procedure. 7. Range Adjustments The range is pre-set at 200 millivolts. You should not have to adjust the range. If you do need to adjust the range, connect minus of your multi-meter to the Ground (you can use a screw number 3 in the Picture 2) and plus of your multi-meter to Reference Voltage test pin (screw number 7 in the Picture 3) of the EFIE while making these adjustments. Counterclockwise will increase (Leaner) and clockwise will decrease (Richen) the range. Do not overlook about a jumper which disable Soft Start Feature. Measurements: Reference Voltage minus of Multi-meter to a screw number 3 in the Picture 2, plus of Multi-meter to screw number 7 in the Picture 3. O2 sensor output signal minus of Multi-meter to a screw number 3 in the Picture 2, plus of Multi-meter to screw number 5 in the Picture 3. Output signal from EFIE to ECU (vehicle computer) minus of Multimeter to a screw number 3 in the Picture 2, plus of Multi-meter to screw number 6 in the Picture 3. Remember that your meter is a load and your reading will go down a few millivolts while connected. The special circuit eliminates this lack and allows us to not think about it. One condition: measure the voltage only on special test pins ( Ground (you can use a screw number 3 in the Picture 2), In test pin (5 in the Picture 3), Out test pin (6 in the Picture 3), Reference Voltage test pin (7 in the Picture 3) on the EFIE to read the voltage while adjusting). Note: when the EFIE is powered OFF, it makes the connection between the oxygen sensor and the ECU (vehicle computer), the same as it was before the EFIE was installed. If you ever have need to reconnect the oxygen sensor directly to the computer, just turn the EFIE OFF (disconnect a wire +12 Volt). 9
10 The exact voltage is 2.5 volts to the ECU. Always make an adjustment EFIE at the connected multi-meter. You never should be in extreme measures. I recommend beginning with 200 millivolts. The process of adjusting the EFIE is trial and error. Watch for symptoms of too lean a mix such as rough engine, lack of power, "check engine light" coming on, etc. When these show up, adjust it by turning the adjustment screws clockwise (Richen) until the symptoms go away. Adjustment tip: If you have a high temperature probe, run down the highway with the EFIE turned OFF at least long enough to get the engine up to full operating temperature, and note the temp of your exhaust pipe (near the exhaust manifold). As you increase your voltage offset, this temperature may increase. Don't let it raise more than 180 degrees from your initial test. 10
11 WARRANTY/DISCLAIMER 1. Your EFIE unit will have a 14 day warranty from the date of reception against defects in electronic workmanship in which the device fails to perform its function of regulating the frequency to the car's computer. Warranty is limited to the servicing of the EFIE unit. If it cannot be serviced then a replacement of comparable design or your money back will be sent to you. Any defective unit must be approved before returning. Buyer pays for return shipping. 2. By purchasing the EFIE unit, you agree: that you the buyer assume all risk & responsibility for any damages, injury or death which may occur as a result of incorrect installment and/or fuel adjustment. 11
DEFIE (Digital Electronic Fuel Injector Enhancer) Installation & Operating Instructions.
DEFIE (Digital Electronic Fuel Injector Enhancer) Installation & Operating Instructions. Please note. The DEFIE is not intended to be a fuel saver by itself. The DEFIE designed to be used only in conjunction
More informationWide Band EFIE Installation Instructions. Locate the wide band oxygen sensor current wire
Wide Band EFIE Installation Instructions Install your fuel efficiency device The EFIE is not intended to be a fuel saver by itself. You should install a device that is designed to get more energy out of
More informationInstall instructions for the EFIE and MAF/MAP Combo For Wide Band Oxygen Sensors Only.
Install instructions for the EFIE and MAF/MAP Combo For Wide Band Oxygen Sensors Only. It is highly recommended that you purchase a Haynes or Chilton s repair manual for your specific vehicle with a schematic
More informationThe next step is to determine your signal wire from each 02 sensor. This again will be identified in your repair manual wiring diagram.
Install instructions for True Digital EFIE with MAF/MAP Enhancer. For Narrow Band Oxygen Sensors Only. READ ALL DIRECTIONS BEFORE BEGINNING INSTALLATION It is highly recommended that you purchase a Haynes
More informationInstall instructions for the New 2016 Tuning 101 AFR Control Center For Wide Band Oxygen Sensors Only.
Install instructions for the New 2016 Tuning 101 AFR Control Center For Wide Band Oxygen Sensors Only. It is highly recommended that you purchase a Haynes or Chilton s repair manual for your specific vehicle
More informationInstall instructions for the Tuning 101 AFR Control Center 2 For Wide Band Oxygen Sensors Only.
Install instructions for the Tuning 101 AFR Control Center 2 For Wide Band Oxygen Sensors Only. It is highly recommended that you purchase a Haynes or Chilton s repair manual for your specific vehicle
More informationNEW SIMPLIFIED EASY TO FOLLOW AND UNDERSTAND
NEW SIMPLIFIED EASY TO FOLLOW AND UNDERSTAND Install instructions for the New GM Device #1 EFIE & MAP. For GM Narrow Band Oxygen Sensors Only. If you can read, you can install this device very easily.
More informationOGO-MAP/MAF User Manual
OGO-MAP/MAF User Manual 1 OGO Dual Mode MAP/MAF Sensor Enhancer Ready to Install This Map Sensor Enhancer was built directly from the OGO specifications manual. It has separate Hwy & City adjustments along
More informationSuperlift TruSpeed Speed Sensor Calibrator For Most Ford Trucks and SUVs 1992-Present INSTALLATION INSTRUCTIONS
FORM #33001.06-121703 PRINTED IN U.S.A. PAGE 1 OF 11 INTRODUCTION Superlift TruSpeed Speed Sensor Calibrator For Most Ford Trucks and SUVs 1992-Present INSTALLATION INSTRUCTIONS SUPERLIFT SUSPENSION SYSTEMS
More informationInstallation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14
Installation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14 Thank you for purchasing your remote start from MyPushcart.com - an industry
More informationFORM # PRINTED IN U.S.A. PAGE 1 OF 11
FORM #33002.08-010507 PRINTED IN U.S.A. PAGE 1 OF 11 SUPERLIFT SUSPENSION SYSTEMS 300 Huey Lenard Loop Rd. West Monroe, Louisiana 71292 Phone: (318) 397-3000 Sales / Tech: 1-800-551-4955 FAX: (318) 397-3040
More informationECT Display Driver Installation for AP2 Module
ECT Display Driver Installation for AP2 Module Overview The ECT Display Driver is a small module with a removable wire harness that mounts behind the driver's foot well cover. All wiring connections are
More informationRemote Start Kit for GM Installation RS1/3/4/7 + ADS-DL Tip Sheet
Remote Start Kit for GM Installation RS1/3/4/7 + ADS-DL Tip Sheet rev 1.4 12/16/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to do-it-yourself
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for Wide-Band Exhaust Gas Oxygen Sensor Interface CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING OVERVIEW
More informationD - ADJUSTMENTS Nissan 240SX ENGINE COMPRESSION VALVE CLEARANCE IGNITION TIMING ENGINE PERFORMANCE On-Vehicle Adjustments
D - ADJUSTMENTS 1990 Nissan 240SX 1990 ENGINE PERFORMANCE On-Vehicle Adjustments Nissan; Axxess, Stanza, 240SX ENGINE COMPRESSION 1) Start engine and warm to normal operating temperature. Disconnect distributor
More informationInstallation Instructions for: DT2-AF2 Dual Channel & DT2-AF1 Single Channel Wide Band O2 Sensor Controller for A/F (Lambda) Measurement
Installation Instructions for: DT2-AF2 Dual Channel & DT2-AF1 Single Channel Wide Band O2 Sensor Controller for A/F (Lambda) Measurement WARNING: This installation is not for the electrically or mechanically
More information2002 ENGINE PERFORMANCE. Self-Diagnostics - RAV4. Before performing testing procedures, check for any related Technical Service Bulletins (TSBs).
2002 ENGINE PERFORMANCE Self-Diagnostics - RAV4 INTRODUCTION NOTE: Before performing testing procedures, check for any related Technical Service Bulletins (TSBs). To properly diagnosis and repair this
More informationWOT Box Installation Instructions VW / Audi
Connector Pinout Pin Color AWG Name WOT Box Installation Instructions VW / Audi Description 1 Yellow 18 RPM Connect to Fuel Injector Drive Signal or Ignition Control Signal (varies by car model) 2 Black
More informationLambda Control Fuel Adaptation and Fuel Trim
Lambda Control Fuel Adaptation and Fuel Trim Q: What is Lambda and Lambda Control? A: In the case of a gasoline engine, the optimal mixture of air to fuel for complete combustion is a ratio of 14.7 parts
More informationNEW VINTAGE INSTRUMENT AND GAUGE KIT INSTALLATION INSTRUCTIONS
NEW VINTAGE INSTRUMENT AND GAUGE KIT INSTALLATION INSTRUCTIONS REV.01-033113 INDEX THE BASICS CLUSTER INSTALLATION TACHOMETER OPERATION SPEEDOMETER OPERATION TROUBLESHOOTING WIRING DIAGRAM pg.2 pg. 2 pg.
More informationStep 1 Wiring your remote start. Installation Tips for your Remote Start system (for GM vehicles) V3.3 revised 9/12/2013
Installation Tips for your Remote Start system (for GM vehicles) V3.3 revised 9/12/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to
More informationInstall Guide A Throttle Position Sensor
1879-A Throttle Position Sensor Install Guide Applications: 2002-2006 Acura RSX Type S 2002-2005 Honda Civic Si 2002-2006 JDM Honda Integra Type R Rev 1.0 www.acuityinstruments.com INSTALLATION NOTES:
More informationMODEL 422 Submersible Pump Controller
MODEL 422 Submersible Pump Controller Monitors True Motor Power (volts x current x power factor) Detects Motor Overload or Underload Operates on 120 or 240VAC, Single-phase or 3-phase Built-in Trip and
More informationSTAFOR HHO MAF/MAP fully digital and automatic enhancer (corrector). Installation manual. Version
STAFOR HHO MAF/MAP fully digital and automatic enhancer (corrector). Installation manual. Version 05.14. HHO hydrogen on demand dual fuel systems Introduction The present MAF/MAP Sensor Enhancer is fully
More informationInstallation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013
Installation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader
More informationNOTES: 1489 N THESTA FRESNO, CA PHONE (559) FAX (559)
NOTES: 1489 N THESTA FRESNO, CA. 93703 PHONE (559)486-5444 FAX (559)486-5155 Contents: REMOTE X 2 THIS IS ONLY A GUIDE!!! BUTTON X 16 THE APPLICATIONS SHOWN ARE GENERAL GUIDE LINES OF POSSIBLE APPLICATIONS.
More informationPreparing and programming of ESGI 2 LPG supply system manual
Preparing and programming of ESGI 2 LPG supply system manual Part II Instruction of preparing and programming the ESGI system 1 Technical data of the central unit Vs Power supply voltage 0...16V V i_an
More informationFIGURE 32 3 Most conventional zirconia oxygen sensors and some wide-band oxygen sensors use the cup (finger) type of design.
FIGURE 32 1 Many oxygen sensors are located in the exhaust manifold near its outlet so that the sensor can detect the presence or absence of oxygen in the exhaust stream for all cylinders that feed into
More information1 of 2 9/4/ :27 AM
Ford Mustang IAC IAB - Solving your idle problems http://www.muscularmustangs.com/iac.php 1 of 2 9/4/2010 10:27 AM Solving idle problems part 1 - Cleaning your IAC Does your idle rise and fall over and
More informationNotice Regarding this Upgrade. WARNING! Danger Potential
Notice Regarding this Upgrade WARNING! Danger Potential Although this kit has been designed to be easy-to-install, and has been tested in many installations; caution must be exercised when installing this
More informationSequential Turn Signals TCSF-03 Installation Instructions FOR ONLINE INSTRUCTIONS VISIT OUR WEBSITE AT
Sequential Turn Signals TCSF-03 Installation Instructions FOR ONLINE INSTRUCTIONS VISIT OUR WEBSITE AT WWW.FOXTHUNDERCATS.COM/ELECTRONIXX Thank you for your purchase of the TCSF-03 Sequential Turn Signal
More informationBMW K1200LT / K1200RS Throttle Position Sensor (also called TPS)
BMW K1200LT / K1200RS Throttle Position Sensor (also called TPS) Many hours were spent to validate the information furnished in this document. None of this information should be considered official, neither
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for WEGO IIID Wide-Band Exhaust Gas Oxygen Sensor Interface (Automotive Version) CAUTION: CAREFULLY READ INSTRUCTIONS
More informationInstallation Guide. Thank you for the purchase of our product. You have just unleashed infinite control, power and ability into your hands.
Installation Guide Thank you for the purchase of our product. You have just unleashed infinite control, power and ability into your hands. This product is for race use only by experienced engine tuners.
More informationInstallation Tips for your Crimestopper/ProStart Remote Start system (for GM vehicles) v1.01 updated 2/27/2012
Installation Tips for your Crimestopper/ProStart Remote Start system (for GM vehicles) v1.01 updated 2/27/2012 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing
More informationR53 BOOST GAUGE INSTALL
R53 BOOST GAUGE INSTALL 052009 Thank you for purchasing the ALTA Performance gauge pod. Installation should only be performed by persons experienced in the proper operation of Mini electrical and body
More informationSunbeam Alpine Series III, IV, and V Fuel & Temperature Gauges by Michael Hartman and Thomas Hayden Version 1.4 May 9, 2018
Sunbeam Alpine Series III, IV, and V Fuel & Temperature Gauges by Michael Hartman and Thomas Hayden Version 1.4 May 9, 2018 The Circuit Illustration 1: Temperature & Fuel Gauge Circuits (Series V) Example
More informationWARNING!!! DO NOT OPERATE WHILE DRVING!! INSTALLATION & USER GUIDE
V-FORCE Plus Engineered For Power! WARNING!!! DO NOT OPERATE WHILE DRVING!! INSTALLATION & USER GUIDE Installation Instructions JET V-Force 1. Mounting the V-Force Using the supplied Velcro, Suction Cups
More informationALTERNATOR - BOSCH 35/75-AMP & 40/90-AMP
ALTERNATOR - BOSCH 35/75-AMP & 40/90-AMP 1988 Chrysler LeBaron Convert/Coupe 1988 ALTERNATORS & REGULATORS Chrysler Motors - Bosch 35/75 & 40/90 Amp Alternator All Models DESCRIPTION The charging system
More information715B CONTROL SERIES. Instruction Manual Line Voltage DC Brushless Motor Control CONTROLS. Phone (317) Fax (317)
715B CONTROL SERIES CONTROLS Instruction Manual Line Voltage DC Brushless Motor Control LT715B (IM-715B-0100) P.O. Box 10 5000 W. 106th Street Zionsville, Indiana 46077 Phone (317) 873-5211 Fax (317) 873-1105
More informationGreddy E-manage Installation and Tuning Information
Greddy E-manage Installation and Tuning Information Overview The Emanage has a lot of functionality considering it is still a piggyback type engine management system and not a full standalone. By itself,
More informationTROUBLESHOOTING AND MAINTAINING ELECTRONIC KILN CONTROL SYSTEMS
TROUBLESHOOTING AND MAINTAINING ELECTRONIC KILN CONTROL SYSTEMS Tom Salicos American Wood Dryers Clackamas, Oregon After many years of helping American Wood Dryers' customers troubleshoot dry kiln control
More informationUSB Charge Port Installation Instructions
USB Charge Port Installation Instructions Lifetime Technical Support support@logolites.com 770-476-7322 www.logolites.com Manual 100-0014C Thank you for purchasing a Logo Lites USB Charge Port! USB Charge
More informationNEW VINTAGE INSTRUMENT AND GAUGE KIT INSTALLATION INSTRUCTIONS 3-1 INSTRUMENT KITS SPEEDO/TACH KITS REV
NEW VINTAGE INSTRUMENT AND GAUGE KIT INSTALLATION INSTRUCTIONS 3-1 INSTRUMENT KITS SPEEDO/TACH KITS REV.01-032912 INDEX THE BASICS FUNCTIONS AND SENDERS TACHOMETER OPERATION SPEEDOMETER OPERATION TROUBLESHOOTING
More informationBMW K1200LT / K1200RS Testing a Throttle Position Sensor (also called TPS)
BMW K1200LT / K1200RS Testing a Throttle Position Sensor (also called TPS) Many hours were spent to test and validate the information furnished in this document. None of this information should be considered
More informationCatalytic Failures. Engine running too hot.
Catalytic Failures It is not uncommon for technicians to misdiagnose a driveability or emissions issue by blaming the converter. In many cases, it s not the converter s fault, but rather one of the engine
More informationExperiment 3: Ohm s Law; Electric Power. Don t take circuits apart until the instructor says you don't need to double-check anything.
Experiment 3: Ohm s Law; Electric Power. How to use the digital meters: You have already used these for DC volts; turn the dial to "DCA" instead to get DC amps. If the meter has more than two connectors,
More informationInstallation Tips for your Remote Start system (for Toyota Camry & Prius C, ) Crimestopper RS0+ EVO-ALL T3468 rev#1.
Installation Tips for your Remote Start system (for Toyota Camry & Prius C, 2012-2014) Crimestopper RS0+ EVO-ALL T3468 rev#1.1 1/22/2015 Thank you for purchasing your remote start from MyPushcart.com -
More informationMarine Exhaust Temperature Alarm. COMPONENTS
Marine Exhaust Temperature Alarm. Model: SM0012 INTRODUCTION COMPONENTS Marine water cooled exhaust systems are designed to withstand temperatures of up to about 120 C. However the exhaust gases from the
More informationVirtual Ground for HV Boosters Calibration
Dear all utracer users, I m writing these lines just to share my experience building my utracer, so that maybe someone could find it useful for his design. The construction of my utracer was very simple,
More informationInstallation Tips for your Add-on Remote Start (for GM vehicles with INTSL Install 2) v3.2 Updated 11/12/2012
Installation Tips for your Add-on Remote Start (for GM vehicles with INTSL Install 2) v3.2 Updated 11/12/2012 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing
More informationENGINE GOVERNING SYSTEMS LSM672 LOAD SHARING MODULE. GOVERNORS AMERICA CORP. 720 Silver Street Agawam, MA , USA MEMBER
ENGINE GOVERNING SYSTEMS LSM672 LOAD SHARING MODULE MEMBER GOVERNORS AMERICA CORP. 720 Silver Street Agawam, MA 01001-2907, USA LSM672 LOAD SHARING MODULE PRODUCT TECHNICAL INFORMATION PTI 4000 AUGUST
More informationTIP SHEET T2352, T3396. Installation Tips for RS1 + EVO-ALL 1-BUTTON REMOTE STARTER FOR: Acura RDX PUSH-TO-START / AUTOMATIC
Installation Tips for RS1 + EVO-ALL 1-BUTTON REMOTE STARTER FOR: Acura RDX 2013-2015 PUSH-TO-START / AUTOMATIC TIP SHEET T2352, T3396 Thank you for purchasing your remote start from MyPushcart.com - an
More informationadvanced FLOW engineering Instruction Manual P/N:
advanced FLOW engineering Instruction Manual P/N: 77-84010 Make: Chevrolet Model: Silverado HD Year: 2017-2018 Engine: V8-6.6L (td) Duramax (L5P) Make: GMC Model: Sierra HD Year: 2017-2018 Engine: V8-6.6L
More informationG203V / G213V MANUAL STEP MOTOR DRIVE
G203V / G213V MANUAL STEP MOTOR DRIVE PRODUCT DIMENSIONS PHYSICAL AND ELECTRICAL RATINGS Minimum Maximum Units Supply Voltage 18 80 VDC Motor Current 0 7 A Power Dissipation 1 13 W Short Circuit Trip 10
More informationINSTALLATION INSTRUCTIONS
THANK YOU FOR CHOOSING KURYAKYN! Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation,
More informationV-FORCE Plus. Engineered For Power! WARNING!!! DO NOT OPERATE WHILE DRVING!! INSTALLATION & USER GUIDE First: Follow the Installation Guide
V-FORCE Plus Engineered For Power! WARNING!!! DO NOT OPERATE WHILE DRVING!! INSTALLATION & USER GUIDE First: Follow the Installation Guide Card provided or Visit our Site for Wiring Charts 2015 JET Performance
More informationInstallation Tips for your Remote Start/Keyless Entry (for Honda/Acura Vehicles) [EVO-ALL] v1.02 updated 9/13/2013
Installation Tips for your Remote Start/Keyless Entry (for Honda/Acura Vehicles) [EVO-ALL] v1.02 updated 9/13/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in
More informationTECHNICAL NOTE #4 Revised May 24, BOGART ENGINEERING Two Bar Road, Boulder Creek, CA (831)
TECHNICAL NOTE #4 Revised May 24, 2004 BOGART ENGINEERING 19020 Two Bar Road, Boulder Creek, CA 95006 (831) 338-0616 TROUBLESHOOTING the TriMetric battery monitor Revised for the TM-2020 TriMetric What
More information30140 F5 Dual Fan Controller
30140 F5 Dual Fan Controller 1 2501 Ludelle Street Fort Worth, Texas 76105 817-244-6212 Phone 817-244-4024 Fax 888-350-6588 Sales 800-423-9696 Tech E-mail: painless@painlessperformance.com Web: www.painlessperformance.com
More informationNEW VINTAGE INSTRUMENT AND GAUGE KIT INSTALLATION INSTRUCTIONS 3-1 INSTRUMENT KIT REV
NEW VINTAGE INSTRUMENT AND GAUGE KIT INSTALLATION INSTRUCTIONS 3-1 INSTRUMENT KIT REV.02 07.11.11 INDEX THE BASICS FUNCTIONS AND SENDERS TACHOMETER OPERATION SPEEDOMETER OPERATION TROUBLESHOOTING WIRING
More informationadvanced FLOW engineering Instruction Manual P/N: Make: Ford Model: F-150 Raptor Year: Engine: V6-3.
advanced FLOW engineering Instruction Manual P/N: 77-83023 Make: Ford Model: F-150 Raptor Year: 2017-2018 Engine: V6-3.5L (tt) EcoBoost Please read the entire instruction manual before proceeding. Ensure
More informationDynoTune Wideband Gauge
DISPLAY: RED GREEN BLUE DynoTune Wideband Gauge FACE: BLACK WHITE BEZEL: BLACK SILVER PACKAGE: ROUND SQUARE The DynoTune A/F Gauge will display the air/fuel ratio output from the LC-2 Wide- Band controller.
More informationThrottle Body Instruction Sheet
Throttle Body Instruction Sheet Thank you for purchasing our modified O.E.M. or new Billet throttle body. They have proven to give considerable power increases when properly adjusted and used alone on
More informationCARM INTERNATIONAL TOWING MODULES
CARM INTERNATIONAL TOWING MODULES (TA100/200 Instructions Revision = 1) Each Towing Module (if ordered with Loom Pack) is shipped with: A/ These instructions B/ 1 x Towing Control Module C/ 1 x high current
More informationHarris IRT Enterprises Digital Resistance Tester Model XP
Harris IRT Enterprises Digital Resistance Tester Model 5012-06XP Specifications & Dimensions 2 Theory of Operation 3 Operator Controls & Connectors 4 Test Connections 5 Calibration Procedure 6-7 Options
More informationTHE IDIOT S GUIDE TO TUNING SU CARBURETTERS
THE IDIOT S GUIDE TO TUNING SU CARBURETTERS There are four distinct phases to tuning SU carburetters (carbies). The first is to set the fuel level in the float bowl, the second is to centre the needle
More informationG213V STEP MOTOR DRIVE REV 7: March 25, 2011
Thank you for purchasing the G213V drive. The G213V is part of Geckodrive s new generation of CPLD-based microstep drives. It has short-circuit protection for the motor outputs, over-voltage and under-voltage
More informationHPC Radiator Fan Control Kit
Revised 06.25.14 www.hpcontrols.ca odels Covered 102002, 102003, 102004, 102005 HPC Radiator Fan Control Kit (102002 Shown) The HPC Radiator Fan Controllers provide automatic control over one or more electric
More informationFuel Metering System Component Description
1999 Chevrolet/Geo Tahoe - 4WD Fuel Metering System Component Description Purpose The function of the fuel metering system is to deliver the correct amount of fuel to the engine under all operating conditions.
More informationPLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 QUICK START GUIDE (HT & HT059980) Version 4
PLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 (HT059970 & HT059980) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: PH:
More informationATLAS Wheel Balancer Electrical Flow Chart
ATLAS Wheel Balancer Electrical Flow Chart WARNING: Leave all work to trained and licensed electricians. Attempting repairs yourself is extremely dangerous, with the potential for serious injury and even
More informationINSTALLATION INSTRUCTIONS
Backup Camera Interface (Kit # 9002-7762) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Cam T-Harness Plug & Play I/O T-Harness
More informationEFI HARNESS KIT , & Kit Contents: Power Harness : All Kits
EFI HARNESS KIT 558-500, 558-501 & 558-502 Kit Contents: Main Harness 558-102: Kits 558-500 558-103: Kits 558-501 & 502 Power Harness 558-308: All Kits Injector Harness 558-200: Kits 558-500 & 502 558-201:
More informationBipes ACU Auxiliary Control Unit for Timing and Knock Control. 2.6" W x 4.25" L x 0.875" H Timing control for '90-'97 Miatas
Bipes ACU Auxiliary Control Unit for Timing and Knock Control 2.6" W x 4.25" L x 0.875" H Timing control for '90-'97 Miatas 1 This page is intentionally blank. 2 Table of Contents Introduction... 4 ACU
More informationM-Tuned reroute kit XX
M-Tuned reroute kit 14-161XX Manufactured and designed by: *Professional Installation Recommended but not required 1) Disconnect the negative terminal from the battery in the trunk. 2) Drain the coolant
More information(905)
(905)953-9260 Marc@M-Tuned.com Coolant Reroute Kit *Professional Installation Recommended but not required 1) Disconnect Negative Terminal from Battery in trunk. 2) Drain Coolant from your cooling system.
More informationInstallation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles)
Installation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles) Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to doit-yourself
More informationChrysler Electronic Ignition System
1 of 11 1/6/2010 11:02 PM Chrysler Electronic Ignition System Classic Winnebago's Post by: DaveVA78Chieftain on August 13, 2009, 10:15 PM Components The Chrysler Electronic Ignition System consists of
More informationM-TUNED COOLANT RE-ROUTE KIT
M-TUNED COOLANT RE-ROUTE KIT Part # MC-RR-216, MC-RR-218 Applications: 90-93 Miata 1.6L B6 94-97 Miata 1.8L BP More detailed instructions: http://www.etdracing.com/m-tuned/reroute.pdf 1) Disconnect Negative
More informationCP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM
CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM Installation And Operation Manual MEGATRONIX VAN NUYS, CA U.S.A. CP634 1 REMOTE CONTROL CONVENIENT SYSTEM INSTALLATION & OPERATION INSTRUCTIONS INTRODUCTION
More informationTIP SHEET. Installation Tips for SP-404/SP EVO-ALL + SPDT Remote Start/Alarm T1642
TIP SHEET Installation Tips for SP-404/SP-502 + EVO-ALL + SPDT Remote Start/Alarm T1642 Nissan Armada: 2008-2012 Nissan Cube: 2009-2012 Nissan Frontier: 2008-2012 Nissan Pathfinder: 2009-2012 Nissan Quest:
More informationFeature Description. Version History
TA2 Malfunction Indicator Lamp (MIL) and Engine Protection Document Number: FD-0007 Author: J. Goodloe Version: 03 Publish Date: 2016-03-18 Feature Description Version History Version Date Modified Sections
More informationCP-1TT Remote System
CP-1TT Remote System (9 volt & 12 volt systems) INSTALLATION/OPERATION MANUAL Manufactured by: Preferred Technologies Group www.cartell.com TABLE OF CONTENTS This Table of Contents is clickable. Point
More informationSCHNITZ MOTORSPORTS USER MANUAL AND INSTALLATION GUIDE PRO-MOD BATTERY VOLTS DIAGNOSTICS NOS PULSE FREQUENCY NOS DELAY TIME IN SECONDS
SCHNITZ MOTORSPORTS DSC-CS "PRO-MOD" IGNITION CONTROLLER USER MANUAL AND INSTALLATION GUIDE COIL, (OPTIONAL) GA YELLOW, COIL, NEGATIVE GA WHITE, GA BLACK, SHIFT LIGHT +V OUTPUT PAGE 0 NOS ACTIVATION INPUT
More informationInstallation Tips for RS1 + EVO-RIDE + SPDT. *(reglar key, automatic transmission vehicles ONLY)*
Installation Tips for RS1 + EVO-RIDE + SPDT TIP SHEET T1235 *(reglar key, automatic transmission vehicles ONLY)* Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing
More informationModel: AEM14 Analog Engine Monitor
Model: AEM14 Analog Engine Monitor Installation and Setup Manual Version 1 Table of Contents Monitor Overview DMK Engine Monitor Kit Section 1: Initial Setup 1.1 Internal Settings Switches Figure 1. AEM14
More informationDirect Link Basic Tuning Guide (Delphi)
Direct Link Basic Tuning Guide (Delphi) This Guide is intended to answer basic Direct Link tuning questions and to act as a Quick Start Guide. It is not intended to be the Gospel on the tuning process
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for Wide-Band Exhaust Gas Oxygen Sensor Interface CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING OVERVIEW
More informationINSTALLATION GUIDE Table of Contents
CT-3100 Automatic transmission remote engine starter systems. What s included..2 INSTALLATION GUIDE Table of Contents Door lock toggle mode..... 4 Notice...2 Installation points to remember. 2 Features..2
More informationTIP SHEET T0937. Installation Tips For RS00/PS00 + ADS-TBSL-PL + SPDT
Installation Tips For RS00/PS00 + ADS-TBSL-PL + SPDT TIP SHEET T0937 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to do-it-yourself installers
More information470nF REG1 LM2940. VR3 100k 10k VR1 100 F. 470pF. 100nF. 100nF RELUCTOR Q2 BC k. 10k TP GND. 2.2nF TO RELUCTOR. 470nF REG1 LM2940 REG1 LM2940
Where to buy kits Jaycar and Altronics have full kits (including the case) available for the High Energy Electronic Ignition System. The Jaycar kit is Cat. KC-5513 while the Altronics kit is Cat. K4030
More informationAPSX WIDEBAND D2 AFR CONTROLLER GAUGE. Installation and User Manual. APSX WIDEBAND D2 Manual V1.0
APSX WIDEBAND D2 AFR CONTROLLER GAUGE Installation and User Manual APSX WIDEBAND D2 Manual V1.0 You purchased a wideband gauge! BENCH TEST BEFORE INSTALLING IT! USE A RELIABLE 12V POWER > 5AMP Stock (OEM)ECU
More informationDynoTune Wideband Gauge
DISPLAY: RED GREEN BLUE DynoTune Wideband Gauge FACE: BLACK WHITE BEZEL: BLACK SILVER PACKAGE: ROUND SQUARE The DynoTune A/F Gauge will display the air/fuel ratio output from the LC-1 Wide-Band controller.
More informationoubleshooting Guide diesel - gasoline - LPG electric P.O. Box 1160 St. Joseph, MO Fax:
Troub oubleshooting Guide diesel - gasoline - LPG electric P/N 0162737 October 2005 P.O. Box 1160 St. Joseph, MO 64502-1160 1-800-255-0317 Fax: 785-989-3075 www.snorkelusa.com GENERAL INFORMATION This
More informationChapter 2. Battery Charger and Base Assembly
Chapter 2 Battery Charger and Base Assembly 11 CHAPTER 2. BATTERY CHARGER AND BASE ASSEMBLY 2.1 Section Overview This Lab teaches students how to assemble a Tekbot, in the following steps: Describe the
More informationRSR Dual O2 Meters Indian Chief rbracing-rsr.com 20 January 2018
Note: Delphi 12mm O2 Sensors have four wires Installation: Dual O2 Wiring Sequence: Sequential EFi; Red (12VDc switched positive) to System Relay Power Wires. Black (GND to Battery Negative Terminal) Green
More informationTable of Contents Title Page No.
Table of Contents Title Page No. INTRODUCTION 1 SAFETY PRECAUTIONS / WARNINGS 2 CONTROLS AND INDICATORS 4 PREPARATION AND CAUTION BEFORE USE 5 TESTING PROCEDURES 6 A. AC/DC VOLTAGE MEASUREMENT 6 B. RESISTANCE
More informationVS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1
VS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1 VS 315 2 INSTALLATION We recommend insulating all your soldered or crimped connections
More informationUNIVERSAL GAUGE WIRE HARNESS
2650-1797-00 UNIVERSAL GAUGE WIRE HARNESS For Installing Auto Meter Electric Speedometer, Tachometer, And Short Sweep Electric Oil Pressure, Water Temperature, Fuel Level, and Volt Meter Gauges. This harness
More information