PARTS LIST FOR HSP MGH/3MGV (AFTER SERIAL # )

Transcription

1 PARTS LIST FOR HSP MGH/3MGV (AFTER SERIAL # ) ENGINE OIL GRADE: HONDA: VANGUARD: ENGINE OIL CAPACITY: HONDA: VANGUARD: SAE10W-30 Above 40 F=SAE30 Below 40 F=SAE10W oz. 51 oz. Pump Oil Grade: SAE20 or 30 Non-Detergent PUMP OIL capacity: 15 oz. BTU INPUT: 294,000 / hour Pressure Nozzle Size: 3.5

2 This Parts Listing has been compiled for your benefit. You can be assured your hot water pressure washer was constructed and designed with quality and performance in mind. Each component has been rigorously tested to insure the highest level of quality. The contents of this Parts Listing are based on the latest product information available at the time of publication. The manufacturer reserves the right to make changes in price, color, materials, equipment, specifications or models at any time without notice. WARNING THIS IS A PROFESSIONAL HIGH PRESSURE, HOT WATER PRESSURE WASHER. CAUTION SHOULD BE OBSERVED WHEN USING OR REPAIRING THIS UNIT! READ AND FOLLOW THE SAFETY WARNINGS LISTED BELOW BEFORE ATTEMPTING ANY REPAIRS ON THIS PRESSURE WASHER! SAFETY WARNINGS 1. NEVER alter or modify the equipment. Be sure any accessory items and system components being used will withstand the pressure developed. Use only genuine manufacturer parts for repair of your pressure washer. Failure to do so can cause hazardous operating conditions and will VOID warranty. 2. NEVER make adjustments on machinery while the unit is connected to the engine without first removing the ignition cable from the spark plug. Turning over the machinery by hand during adjustment or cleaning might start the engine and machinery with it, causing serious injury to the operator. 3. Know how to stop and bleed pressures quickly. Be thoroughly familiar with controls. 4. Before servicing the unit, turn unit off, relieve the water pressure and allow the unit to cool down. Do not make repairs while the unit is running. Service in a clean, dry, flat area. Block the wheels to prevent the unit from moving. Be especially careful to properly dispose of any flammable materials. 5. After testing the machine, DO NOT leave the pressurized unit unattended. Shut off the unit and release trapped pressure before leaving. Table of Contents SPECIFICATIONS...3 FLOW CHART...4 EMF SYSTEM...4 GENERAL THEORY OF OPERATION...5 DECAL PLACEMENT...6 FRAME (AFTER SERIAL # )...8 ENGINE/ PUMP ASSEMBLY...10 HIGH PRESSURE PUMP (3-0194)...12 UNLOADER/MANIFOLD ASSEMBLY...14 UNLOADER ( )...16 PRESSURE SWITCH ( )...18 DETERGENT INJECTOR ( )...20 COIL DRAIN PLUG ( )...21 HEAT EXCHANGER/EMF SYSTEM...22 BOILER ASSEMBLY ( ) AFTER SERIAL # ELECTRODE GAP SETTINGS...24 GUN ASSEMBLY ( )...26 DUAL LANCE ASSEMBLY ( )...28 FUEL TANK ( )...30 FUEL PUMP (3-0020) & FUEL SOLENOID ( )...32 EMF SYSTEM ( )...34 ELECTRIC BOX...36 WIRING SCHEMATIC / DIAGRAM

3 SPECIFICATIONS MODEL NUMBER HSP MGH HSP MGV Operating Pressure (PSI/Bar): 500/2 (+/- 5%) Water Volume (GPM/lpm): 3.3/12.5 (+/- 5%) Outlet Water Temperature (F/C): 140 F/78 C (+/- 20 F) rise above inlet ambient (210 F/ 99 C maximum) Engine: Honda Briggs & Stratton Vanguard Horsepower Engine Type Four Stroke, Overhead Valve, Single Cylinder Oil Type SAE0W-0 Above 40 F=SAE30/ Below 40 F=SAE 10W-30 Oil Capacity (oz./ liter) 37/1.1 51/1.5 Low Oil Protection Oil Alert TM Oil guard TM Fuel Type Unleaded Gasoline 86 Octane Minimum Fuel Capacity (gal./ liter) 1.72/ /6.8 Starting Recoil Rope Maximum No Load RPM 00 (+/- 00) High Pressure Pump: Direct Driven, Oil Bath, Triplex Piston Oil Type SAE20 or 30 Non-Detergent Oil Capacity (oz./liters) 15/.44 Plungers Manifold Valves Unloader Inlet Water Strainer Heat Dump Valve Detergent Injector: Burner Fuel System: Fuel Type Ceramic Forged Brass Stainless Steel Preset Removable Clear Bowl for inspection and cleaning of Stainless Steel Screen Relieves heated water during unloader bypass stage Adjustable Low Pressure downstream from pump No.1 or No.2 Fuel Oil, Diesel or Kerosene Fuel Capacity (gal./liters) 5.5/21 Fuel Filter/ Water Separator Fuel Pump Fuel Pressure (PSI/ BAR) Fuel Nozzle Spin on (10 micron) filter/ E-Z water drain Two Line, Single Stage 5/ B Delavan Fuel Consumption (gph/ LPH) 2.1 GPH Continous Burning Electro Magnetic Firing (EMF) System: Belt Driven (Patent # 5,954,494) Ignition Control Voltage Blower Heat Exchanger: Transistorized Magneto 12 Volt DC Forced Air Vertical, Top fired, Dual Spiral Coil BTU Input 29,000 Efficiency Smoke Density Controls: On/ Off Switch Pressure Switch 86% with #2 Fuel Oil/ Diesel 0-3 per ASTM D2156 Industrial grade rocker switch Shuts off burner fuel supply upon trigger release High Limit Switch Shuts off burner fuel supply when outlet water temp. exceeds 210 F/ 99 C Fuel Solenoid: 12 Volt Safety Relief: Relieves excess system pressure Unit Net Weight (Lbs/kg): 28/9 0/95 Unit Shipping Weight (Lbs/kg): 55/250 55/25 Unit Net Dimension (In/cm): Unit Shipping Dimension (In/cm): 43Lx 30Wx 41H/109L x 76W x 104H 46.5L x 31.5W x 48.5H/118L x 80W x 123H

4 FLOW CHART EMF SYSTEM OMHSP RZ OMHSP BAR

5 GENERAL THEORY OF OPERATION WATER FLOW: Connect a pressurized water source to the Inlet Garden Hose Connection (1) and turn on the water supply. The water will flow through a Water Strainer (2) which has a clear inspection bowl. The water then travels into the Triplex High Pressure Pump (3) which has an Unloader (4) that bypasses the water when the trigger gun is closed. To protect the pump from heated water during this bypass stage, a Heat Dump Valve (5) will open at 140 F/60 C allowing the heated water to escape. The Heat Dump Valve automatically resets when the water cools. the Pressure Switch (6) controls the fuel supply to the burner. When using detergents, the solution passes through the Detergent Strainer (7) located on the Detergent Hose (8). The detergent solution then travels into the Adjustable Low Pressure Detergent Injector (9). From there, the water may be allowed to flow out of the drain plug (10) or through the heat EXCHANGER INLET (11) where it is heated when the burner is on. As the water exits the Heat Exchanger OUTLET (12), it enters a safety system which protects the operator from danger. The safety system contains a High Temperature Limit Switch (13) which senses the water temperature and shuts off the fuel supply to the burner if it gets too hot. If the unloader fails to by pass the water or the burner remains on when the trigger gun is closed, the SAFETY RELIEF (14) will relieve and allow water to exit safely. The heated water then flows through the High Pressure Hose (15) and to the Trigger Gun Assembly (16) which allows the operator to control the water spray. When the trigger gun is open, the water flows through the Adjustable Pressure Dual Lance (17) and exits the Nozzle (18). FUEL FLOW: The Fuel Pump draws fuel from the Fuel Tank (19) through a replaceable Fuel Filter/Water Separator (20) and into the Fuel Pump (21). Fuel exits the fuel pump, into a Fuel Solenoid Valve (22) which controls fuel flow to the Fuel Nozzle (23) where it ignites and burns in the heat exchanger. EMF SYSTEM: The patented Electro Magnetic Firing (EMF) System is an integrated system which gives all the requirements for combustion. The Belt (1) from the power source turns the Hub (2) which has two Exterior Magnets (3) attached. As these magnets spin past the Ignition Module (4), a magnetic flux is created from which the ignition module produces a high voltage. This voltage arcs across the electrodes giving the spark that is needed for ignition. This hub has an Internally Mounted Magnet (5) which spins past a Stator (6) that produces the voltage that controls the fuel supply to the heat exchanger. In addition to this, the hub also spins the Blower Fan (7) that forces the air into and through the heat exchanger. The Fuel Pump (8) is also connected the hub by means of a flexible coupler. 5

6 DECAL PLACEMENT HSP MGH/GV GEN RZ

7 HSP MGH/GV RZ DECAL PLACEMENT REF. # DESCRIPTION PART # QTY. Decal- Warni ng: Don't Modify Plumbing (E/S) (See ) N/A Sep. 2 Decal- Clear Laminate n/a Decal- Data Plate n/a Decal- Serial Number n/a 5 Decal- Warni ng: Hot Coil Exhaust (E/S) (See ) N/A Sep. Decal- Allow to Cool (E/S) (See ) N/A Sep. 7 Decal- Hot Surface (E/S) (See ) N/A Sep. 8 Decal- Risk of Fire (E/S) (See ) N/A Sep. 9 Decal- Burner On/Off (E/S) (See ) N/A Sep. 0 Decal- Warni ng/ Caution/ Operation (E/S) (See -900) N/A Sep. Decal- Stripe Logo Decal-White Die Cut -005 Decal-Stripe Logo -050 Decal- Mi-T-M Logo

8 FRAME (AFTER SERIAL # ) HSP RZ 8

9 HSP099 HSP Rz FRAME (AFTER SERIAL # ) REF. # DESCRIPTION PART # QTY. REF. # DESCRIPTION PART # QTY. Frame Assembly 5-020A0 22 Handle grip Wheel Brake Handle Assembly A0 jam Nut Washer Bolt Screw Flatwasher Lockwasher High Pressure Hose Assembly Locknut Bolt Bracket/Electric Box Assembly (See Exploded Drawing) N/A Sep. 8 Unloader/ Manifold Assembly (See Exploded Drawing) N/A Sep. 29 Wire Tie Fuel Clamp Fuel Hose Assembly Hose *(Two Feet Required) Heat Exchanger/EMF Assembly (See Exploded Drawing) N/A Sep. Hex Nut Hood Assembly High Pressure Hose Assembly 5-09 Hand Knob Fuel Tank Assembly (Includes 14, 15) Trim Lock *(One Foot Required) -029 Countersunk Hex Head Plug Screw Connect Fuel Cap 2-00 Hose Assembly 5-0 Fuel Hose gun Assembly Engine/Pump Assembly (See Exploded Drawing) N/A Sep. 8 Dual Lance Assembly Shim Nozzle Bracket A0 0 Nozzle grommet -0 *Must Order in One Foot Lengths 2 Washer

10 ENGINE/ PUMP ASSEMBLY HSP RZ 10

11 HSP00_HSP Rz ENGINE/ PUMP ASSEMBLY REF. # DESCRIPTION PART # QTY. REF. # DESCRIPTION PART # QTY. Hose Gasket Plug Hose Swivel Pressure Switch Strainer Complete (Includes -7) Heat Dump Valve Strainer Bowl Elbow Screen High Pressure Hose 5-09 Strainer O-ring Set Screw Strainer Cap Bolt Elbow Key (HSP MGH) Hose Clamp Key (HSP MGV) Hose *(Two Feet Required) Oil Drain Plug n/a High Pressure Pump Washer (HSP MGH) Bolt Washer (HSP MGV) Lockwasher Oil Drain Port (HSP MGH) 2-0 Flatwasher Oil Drain Port (HSP MGV) Flange/ Pump Adapter Exhaust Deflector (HSP MGV) Belt -007 Engine- 13 H.P. Honda (HSP MGH) Sheave Engine- 13 H.P. Vanguard (HSP MGV) Set Screw Beltguard 20-08A0 9 Bolt Bolt Adaptor Plate *Must Order in One Foot Lengths 11

12 HIGH PRESSURE PUMP (3-0194) RD 12

13 RD PUMP ASSEMBLY (3-0194) REF. DESCRIPTION PART # QTY. REF. DESCRIPTION PART # QTY. REF. DESCRIPTION PART # QTY. Bolt Plunger Rod O-ring Shaft Cover Slinger Washer Plug Oil Seal Back-up Ring Plug O-ring O-ring Manifold Bearing Piston -070 Valve Cap Set Screw Washer 2-09 O-ring Crankshaft (After Serial #28511) nut Single Valve Assembly (Inc ) (See ) N/A Sep. - Crankshaft (Before Serial #28511) Oil Dipstick O-ring (See ) Plug Bearing Cap Valve Seat (See ) N/A Sep. 9 O-ring Shim- 0.1mm (Qty. Varies 1-3) Valve Plate (See ) N/A Sep. 0 Plug Shim- 0.2mm (Qty. Varies 1-3) Valve Spring (See ) N/A Sep. Bolt O-ring Valve Cage (See ) N/A Sep. 2 Crankcase Cover -079 Bearing (After Serial #28511) Plug O-ring Bearing (Before Serial #28511) O-ring Oil Sight glass Crankcase Bolt Reflector -082 Oil Seal Lockwasher Retainer -07 O-ring High Pressure Seals (Inc. 3 each 34, 35, 37) O-ring Low Pressure Seal (See ) N/A Sep. Support Rings (Inc. 3 each 38) Connecting Rod (After Serial #28511) Packing Retainer Valve Kit (Inc. 6 each 46-50) Connecting Rod (Before Serial #28511) V-Packing (See ) N/A Sep. Oil Seals Kit (Inc. 3, 4, 17, 30, 33) Piston Pin Support Ring (See ) N/A Sep. Piston Kit (Inc. 3 each 21-26)

14 UNLOADER/MANIFOLD ASSEMBLY OMHSP BAR 14

15 OMHSP BAR UNLOADER/MANIFOLD ASSEMBLY REF. # DESCRIPTION PART # QTY. Hose *(Two Feet Required) Hose Clamp 2-00 Elbow 2-09 Unloader Assembly Plug Detergent Injector Manifold Block High Pressure Hose Assembly Detergent Strainer Detergent Hose *(Six Feet Required) High Pressure Hose Assembly 5-09 *Must Order in One Foot Lengths 15

16 UNLOADER ( ) OMGEN BAR 16

17 OMGEN BAR UNLOADER ( ) REF. # DESCRIPTION PART # QTY. Hex Nut Cover Set Screw Adjusting Insert- Brass Adjustment Nut 8-0 Set Screw glide Ring Spring Hex Nut Bushing 8-08 Unloader Body Retainer Valve Housing 8-00 Spring Valve O-ring Cylinder Pin Piston Repair Kit Spacer Stop nut Washer Check Valve Repair Kit (Includes 13-16) Unloader Complete

18 PRESSURE SWITCH ( ) & BAR 18

19 BAR PRESSURE SWITCH ( ) REF. # DESCRIPTION PART # QTY. Pressure Switch Screw n/a Cover n/a O-ring (See 70-00) N/A Sep. 5 Micro Switch n/a Retainer Clip n/a 7 Body n/a 8 O-ring (See 70-00) N/A Sep. 2 9 Back-up Ring (See ) N/A Sep. 0 Piston n/a Washer n/a 2 Spring 9-0 Washer n/a Plastic Housing n/a 5 O-ring (See 70-00) N/A Sep. nut n/a 7 Wire Assembly n/a O-ring Repair Kit (Inc. 4, 8-9, 15)

20 DETERGENT INJECTOR ( ) RD DETERGENT INJECTOR ( ) REF. # DESCRIPTION PART # QTY. Detergent Injector (Inc. 2-11) Orifice (2.1mm) Injector Body n/a Spring (See ) N/A Sep. 5 Ball (See ) N/A Sep. O-ring (See ) N/A Sep. 7 Piston Retainer Spring RD 9 O-ring (See ) N/A Sep. 0 Adjustable Shutter Barb Adjustment Knob Injector Repair Kit (Includes 4-6, 8)

21 COIL DRAIN PLUG ( ) BAR COIL DRAIN PLUG ( ) REF. # DESCRIPTION PART # QTY. Bolt Retaining Cable -020 Snap Ring BAR Hand Wheel Plug 2-07 Back-up Ring O-ring

22 HEAT EXCHANGER/EMF SYSTEM OMHSP BAR 22

23 OMHSP083_ BAR HEAT EXCHANGER/EMF SYSTEM REF. # DESCRIPTION PART # QTY. REF. # DESCRIPTION PART # QTY. Boiler Assembly Complete Bracket 20-00A0 2 2 EMF Assembly Pin -02 Hex Nut Tensioner Sheave Shaft Assembly (Inc. 5, 25, 26) Fuel Pump Coupler Sheave Assembly nut Shaft -022 Flatwasher Access Panel 20-08A0 7 Tensioner Base Bolt Fuel Pump Bracket 20-08A0 29 grommet Bolt grommet Hex Nut Elbow Fuel Hose Assembly High Limit Switch Elbow Outlet Connector Block 2-08 Fuel Solenoid- 12 Volt -000 Pressure Relief Valve Fuel Pump Adapter Elbow nipple Fuel Hose Hex Reducer Hex Nipple High Pressure Hose Assembly Filter Fuel Water Seperator Street Tee Fuel Water Seperator Replacement Bowl Elbow Fuel Water Seperator Replacement Filter Adapter Plate 20-0A0 2 Drain Plug Assembly

24 BOILER ASSEMBLY ( ) AFTER SERIAL # ELECTRODE GAP SETTINGS CH ELECTRODE PLATE ASSY CH 24

25 CH BOILER ASSEMBLY ( ) REF. # DESCRIPTION PART # QTY. REF. # DESCRIPTION PART # QTY. Hex Nut Acorn nut Plug 2-00 nut 0-00 Heat Exchanger Outer Wrap- Black 20-07A0 7 Cone Bolt Fuel Nozzle Air Diverter Plate- Black A0 9 Electrode Plate Air Diverter Stem Assembly- Black A0 20 Bolt Lockwasher Sight glass Hex Nut Snap Ring Bottom Insulation Electrode Washer Electrode Mounting Clip- Black 20-09A0 Heat Exchanger Coil Assembly Bolt Inner Pan Assembly Nozzle Holder Top Pan Assembly- Black 20-07A0 27 Bolt Lockwasher Boiler Assembly Complete (Inc. 1-27)

26 GUN ASSEMBLY ( ) RD 26

27 RD GUN ASSEMBLY ( ) REF. # DESCRIPTION PART # QTY. Plastic Housing Screw Brass Housing -002 Gun Repair Kit Brass Plug Plastic Cover Pipe Assembly Trigger Pin Trigger/Safety Lock-off Pipe Assembly- Inlet -00 Complete gun Assembly

28 DUAL LANCE ASSEMBLY ( ) _ RZ 28

29 Rz DUAL LANCE ASSEMBLY ( ) REF. # DESCRIPTION PART # QTY. Dual Lance Assembly - 48" (Inc. 2-11) Detergent Nozzle 8-00 nut 0-00 Clamp Lower Valve Cover (See ) N/A Sep. Housing (See -07) N/A Sep. 7 Lance Handle Repair Kit Lance (See -07) N/A Sep. 2 0 Screw Nozzle Adapter

30 FUEL TANK ( ) BAR 30

31 BAR FUEL TANK ( ) REF. # DESCRIPTION PART # QTY. Plug Fuel Tank (See ) N/A Sep. Elbow Decal-Warning: Risk of Fire (E/S) (See ) N/A Sep. 5 Flare Fuel Pick-up Line Bushing Fuel Indicator gauge Fuel Cap-Vented 2-00 Safety Decal Kit (Includes 4)

32 FUEL PUMP (3-0020) & FUEL SOLENOID ( ) OMHSP BAR 32

33 0MHSP BAR FUEL PUMP (3-0020) & FUEL SOLENOID ( ) REF. # DESCRIPTION PART # QTY. Cord-Din Connector Base Plate -0 nut -0 Solenoid Coil- 12 Volt Screw n/a 2 Piston Bolt Washer Solenoid Body n/a 0 Plug Fuel Pump Body n/a 2 Cover Gasket Fuel Oil Strainer 9-00 Fuel Pump Cover Fuel Pump Cover Screw

34 EMF SYSTEM ( ) OMHSP BAR 34

35 OMHSP BAR EMF SYSTEM ( ) REF. # DESCRIPTION PART # QTY. EMF Assembly Blower Flange Assembly Bearing Flange Blower Spacer -020 Shaft- Blower/ Electric Woodruff Key Cable Clamp Screw Stator Coil Screw Flange Magnet Hub 8-00 Hex Nut Bolt Flatwasher Ignition Coil Assembly Blower Fan Screw Set w/ Fan

36 ELECTRIC BOX OMHSP BAR 36

37 OMHSP BAR ELECTRIC BOX REF. # DESCRIPTION PART # QTY. Switch/ Rocker Bolt Bolt and Gasket Kit Electric Box Lid- Black 2-00A0 5 Terminal Strip 2-09 Hex Nut Electric Box- Black 2-029A0 8 Electrical Connecter Electric Box Bracket- Black A0 37

38 WIRING SCHEMATIC OMHSP050A BAR 38

39 WIRING DIAGRAM OMHSP050B BAR 39

40 Manufactured by Mi-T-M 8650 Enterprise Drive, Peosta IA / Fax