Parts Catalog Issued: Mar 26, Xterra GT. Power Wheelchair

Transcription

1 Parts Catalog Issued: Mar 26, 2018 Xterra GT Power Wheelchair

2 Parts Catalog Usage Guide The information contained in this document is subject to change without notice. This catalog contains service parts for. If you have any questions regarding this catalog, please contact one of our Customer Service Representatives. SYMBOL DEFINITION For Customer Service Support Call: For Faxed In Orders Call: or For Technical Service Call: Literature Can Be Found at: or Throughout this catalog you will notice letters to draw your attention to specific footnotes which are located at the bottom of the page or below specified charts. Examples: A,B,C etc. NOTE: NLA = Special Comments = General information pertaining to that specific page = No Longer Available HARDWARE MEASUREMENTS The measurements for the hardware will be listed as follows: Screws, Bolts Diameter X Thread Count/Pitch X Length Washers Inside Diameter X Outside Diameter X Thickness Spacers Inside Diameter X Outside Diameter X Length For your convenience, we have supplied an area for you to list your Invacare Representatives. Name Phone Numbers 2018 Invacare Corporation. Elyria, Ohio. Invacare, Yes, you can., and the Blue Medallion Design are registered trademarks and Xterra, GT, MKIV, and RII, are trademarks, and Invacare virtual Service is a service mark name of the Invacare Corporation. Tash is a registered trademark of Tash International Inc.. Therafin is a registered trademark of W/R/ Medical Electronics Co.. Bussman is a registered trademark of Cooper Industries. MIDI is a registered trademark of Littelfuse Inc.. Dynamic is a registered trademark of Dynamic Controls Limited. 1

3 TABLE of CONTENTS Description Page Number Accessories - Miscellaneous Accessories - Power Wheelchair Tool Kit Arms - Adjustable Height (14" - 15" D)... 6 Arms - Adjustable Height (16" - 20" D) Arms - Captain Seat & Hardware (18" W)... 2 Arms - Captain Seat & Hardware (20" W)... 4 Arms - Fixed Height (16" - 20" D)... 8 Battery Charger & Harness Battery Top Cover and Tray Assembly Canes - Back - Spreader Bars & Attaching Hardware Casters & Forks - Front 8" & Rear 6" Electronics - MKIV Controllers, Programmer and Hardware Electronics - MKIV Displays Electronics - MKIV Joystick Mounting Hardware and Joystick Accessories Electronics - MKIV Joystick Options Electronics - MKIV Joysticks - PSF and PSR Electronics - MKIV Joysticks - RII, TCHJOY, A, A Electronics - MKIV Mid-Line Swing Bracket Assembly... 9 Electronics - MKIV R.I.M. Head Control Assembly Electronics - MKIV R.I.M. Head Control Mounting Hardware Electronics - MKIV Sip-N-Puff/Digital Interface and COM12 and COM

4 TABLE of CONTENTS Description Page Number Electronics - MKIV Swivel Joystick Hardware Electronics - Quad Link (QLA - ASBA) and (QL - Captain Seat) (After 4/06/06) Electronics - Quad Link Assembly (Before 4/07/06) Electronics - Tash and Therafin Accessories Fenders & Shrouds Frame - Base with Suspension Arms & Torsion Bar Frame Finishes - Touch-Up Paints & Upholstery Options... 5 Frames - Mounting Hardware ASBA & Captain Seat... 1 Frames - Seat ASBA & Hardware (14" - 15" W)... 9 Frames - Seat ASBA & Hardware (16" - 20" W) Front Riggings - Adjustable Angle Footplates - AT Front Riggings - Adjustable Heel Loops Front Riggings - Cage Style Footrest Front Riggings - Calf Pads and Attaching Hardware Front Riggings - Footrest and Legrest Accessories... 6 Front Riggings - Footrest Support Assemblies Front Riggings - Footrest Supports - PW Front Riggings - Front Rigging Hanger Assembly - Pin, Sector and Cage Style Front Riggings - Legerst Supports - AT Front Riggings - Pivot/Slide Tube and 1650, 1450, 150 Aluminum Footplates Front Riggings - Pivot/Slide Tube and 1651 Composite Footplates... 58

5 TABLE of CONTENTS Description Page Number Front Riggings - Reference Chart (70ST) Front Riggings - Reference Chart (AT5544, 60HD, 70NHD, and PW9) Motors - 4-Pole & Gearbox Assembly Packaging - Literature & Decals... 7 Seat Pan & Mounting Hardware Seat Plate - Flip Up Seat Plate - Flip-Up - Mounting Hardware Seats - Captain Seats - Captain & Actuator Hardware... 2 Suspension Arm - Mounting Hardware Suspension Spring - Front - Mounting Hardware... 7 Upholstery - Back Warranty Replacement Parts Wheels - 16" Drive Wheel & Mounting Hardware

6 Frame Finishes, Touch-Up Paints, and Upholstery Options Frame Finishes and Touch-Up Paints Color Number Part Number Bottle Size Color 08P NLA.6 oz. Deep Purple 17P NLA.6 oz. Cobalt Blue 22P 1076-NLA.6 oz. Anthracite 24P NLA.6 oz. Wet Black 29P NLA.6 oz. White P NLA.6 oz. Red 4P NLA.6 oz. Flat Black 61P NLA.6 oz. Electric Red 62P NLA.6 oz. Electric Blue 66P NLA.6 oz. Electric Purple 69P NLA.6 oz. Teflon Black 71P N/A N/A Silver Vein 80P NLA.6 oz. Evergreen with Navy 8P NLA.6 oz. Royal Blue with Grape 84P NLA.6 oz. Lavender 101P NLA.6 oz. Jeweled Green 102P NLA.6 oz. Denim Blue 10P NLA.6 oz. Mocha Frost 104P NLA.6 oz. Electric Teal 105P NLA.6 oz. Midnight Blue 5

7 Frame Finishes, Touch-Up Paints, and Upholstery Options Sparkle Frame Finishes Color Number 88P Color Wet Black with Twilight Sparkle Upholstery Option Vinyl Colors U67 Black Nylon Colors U240 Black 6

8 Packaging, Literature and Decals NOTE: When adjusting or replacing parts, please refer to your Owner's Manual for assistance. 7

9 Packaging, Literature and Decals NOTE: When adjusting or replacing parts, please refer to your Owner's Manual for assistance. Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Owner's Manual, Xterra GT X01-NLA NLA - Warranty Card NLA NLA - Bag, Poly Zip-Lip (1" L x 9" W) X161 Insert, Plain Pad X00 Carton Carton, Cover NLA NLA - Tube, Paper Bag, Poly (72" L x 5" W x 19" D) X011 Carton, Front Riggings Carton, Tray NLA NLA - Wood Skid NLA NLA - Decal, Battery Removal/Installing Decal, Warning Pinch Point Decal, Transportation NLA NLA - Decal, Notice, Lower Seat Decal, Warning Pinch Point NLA NLA - Decal, Xterra GT NLA NLA - Decal, Invacare Medallion - Large Decal, Invacare -D Logo (2-1/2" L) NLA NLA - Plate, Name, Patent Numbers NLA Carton, Corner Reinforcement 1 4 8

10 ASBA Seat Frame and Hardware 14-15" Wide 9

11 Item Number Note Part Number Description ASBA Seat Frame and Hardware 14-15" Wide Quantity Per Package Assembly Screw, Hex Head (1/4-20 x 1-5/8") Spacer, Coved (1/4 x 11/16 x 1/2") Spacer (1/4 x /8 x /16") Locknut (1/4-20) X074 Spring, Arm Lock Pin, Arm Lock, Black Kit, Lock Handle w/rivets (Pair) 2 1 See Chart #'s 6-8 ASBA Seat Frame and Hardware 1 1 #'s 6-8 Seat Frames NOTE: Item Number Description 14-15" Deep 16-17" Deep 18-19" Deep 20" Deep Seat Frame - Right See Note(s) B Seat Frame - Left See Note(s) B Seat Frame - Center Seat Frame - Assembly NLA NLA NLA NLA See Note(s) A A - Includes items 1-7 B - Seat frame includes item 5 arm lock assembly NLA NLA NLA NLA See Note(s) A NLA NLA NLA NLA NLA NLA NLA NLA 10

12 ASBA Seat Frame and Hardware 16-20" Wide NOTE: 14" and 15" seat depths are achieved by using CJ back mounting hardware. 11

13 ASBA Seat Frame and Hardware 16-20" Wide NOTE: 14" and 15" seat depths are achieved by using CJ back mounting hardware. Item Number Note Part Number Description Quantity Per Package Assembly 1 A See Chart # 1 ASBA Seat Frame and Hardware Plug Button, Black (1") Kit, Lock Handle w/rivets (Pair) X074 Spring, Arm Lock Pin, Arm Lock, Black 1 2 NOTE: A - Includes seat frame and items 2-5 # 1 - Seat Frame with Hardware Seat Width 14-17" Deep 18-19" Deep 20" Deep 16" Wide NLA NLA NLA 17" Wide NLA NLA NLA 18" Wide NLA NLA NLA 19" Wide NLA NLA NLA 20" Wide NLA NLA NLA 12

14 ASBA and Captain Seat Frame Mounting Hardware NOTE: All captin seats use seat frame mounting hardware part #

15 ASBA and Captain Seat Frame Mounting Hardware NOTE: All captin seats use seat frame mounting hardware part # Item Number Note Part Number Description Quantity Per Package Assembly See Chart #1 ASBA and Captain Seat Frame Mounting Hardware NLA NLA - Screw, Hex Head (5/16-18 x 2-1/4") NLA NLA - Tube with End Seat Spacer Assembly, Black Locknut (5/16-18) NLA NLA - Screw, Hex Head (5/16-18 x 2") NLA NLA - Spacer (/8 x /4 x /8") NLA NLA - Plug Button, Square, Black (1-1/4") NLA NLA - Screw, Hex Head (5/16-18 x 1-1/2") 1 4 #1 Seat Frame Mounting Hardware Seat Width 14-17" Deep 18-19" Deep 20" Deep 14-15" Wide NLA NLA NLA 16-18" Wide NLA NLA NLA 19-20" Wide NLA NLA NLA 14

16 Flip-Up Seat Plate Assembly 15

17 Item Number Note Part Number Description Flip-Up Seat Plate Assembly Quantity Per Package Assembly 1 A,D NLA NLA - Seat Plate Assembly, Flip-Up (14-20" D) B,D NLA NLA - Plate, Seat, with Decals, Flip-Up (14-20" D) NLA NLA - Decal, Battery Removal/Installing NLA NLA - Bearing, Flange NLA NLA - Screw, Socket Head w/ Patch (1/4-20 x /4") NLA NLA - Bracket, Handle Release, Black NLA NLA - Bushing, Flanged (1/4 x 1/2 x /8") NLA NLA - Spring, Extension (1/2 x 1-5/2" L) NLA NLA - Hook Release Assembly NLA NLA - Bracket, Support Release, Black NLA NLA - Package, Screw, Phillips Pan Head (#10-2 x 25 1/2") NLA NLA - Handle, Release Locknut (#10-2) 1 14 C NLA NLA - Hardware, Hook Release Decal, Transportation Decal, Warning Pinch Point NLA NLA - Plate, Threaded NLA N LA - Plate, Threaded Prop 1 1 NOTE: A - Includes Items 2 and B - Includes Items, 4, 15, and 16. C - Includes Items 8-1. D - 12/4/02 all seat depths now utilize only one flip-up seat plate assembly with a material depth of 1". For 20" deep models made before 12/4/02 and measure 14", new adjustment brackets must be ordered. See page titled Flip-Up Seat Plate Mounting Hardware. 16

18 Flip-Up Seat Plate Mounting Hardware 17

19 Flip-Up Seat Plate Mounting Hardware Item Number Note Part Number Description Quantity Per Package Assembly 1 A,B NLA NLA - Hardware, Seat Plate Mounting, Flip-Up ( " D) Screw, Shoulder Hex Socket Head (5/16" x /8", 1 1 1/4-20) Washer (5/16 x 9/16 x 1/2") NLA NLA - Washer, Flat (7/8 x 11/2 x 1/16") NLA NLA - Bracket, Prop Seat with Decals, Black NLA NLA - Washer, Spring (5/8 x 1 x 1/16") NLA NLA - Washer, Flat (7/8 x 5/8 x 1/8") NLA NLA - Bushing, Stepped (/8" I.D.) Washer, Flat (5/16 x 5/8 x 1/16") Locknut (5/16-18) Locknut (5/16-18) B NLA NLA - Bracket, Adjustment, Black - Right (14-20" 1 1 Deep) 12 B NLA NLA - Bracket, Adjustment, Black - Left (14-20" 1 1 Deep) Washer, Flat (/8 x 11/16 x 1/16") NLA NLA - Screw, Shoulder Hex Socket Head (/8 x 1", 1 2 5/16-18) Screw, Shoulder Hex Socket Head (/8 x 1-/4", 1 1 5/16-18) NLA NLA - Decal, Notice, Lower Seat Decal, Warning Pinch Point NLA NLA - Screw, Shoulder Hex Socket Head (/8 x /4", 5/16-18) 1 NOTE: A - Includes Items B - 12/4/02 all seat depths now utilize only one flip-up seat plate assembly with a material depth of 1". For 20" deep models made before 12/4/02 and measure 14", a new flip-up seat plate must be ordered. See page titled Flip-Up Seat Plate Assembly. 18

20 Seat Pan and Mounting Hardware NOTE: 14-15" Wide seat depths are achieved by using CJ back cane mounting hardware. 19

21 Seat Pan and Mounting Hardware NOTE: 14-15" Wide seat depths are achieved by using CJ back cane mounting hardware. Item Number Note Part Number Description Quantity Per Package Assembly 1 See Chart #1 Seat Pan A NLA NLA - Kit, Seat Pan Mounting Hardware Screw, Hex Head (1/4-20 x 1-5/8") 1 2 Screw, Hex Head (1/4-20 x 1-1/2") Spacer (1/4 x /8 x /16") Locknut (1/4-20) 1 6 NOTE: A - Includes Items 2-5. #1 - Seat Pan Seat Width 14" Wide 15" Wide 16" Wide 17" Wide 18" Wide 19" Wide 20" Wide 14-15" Deep 16" Deep 17" Deep 18" Deep 19" Deep NLA NLA NLA NLA NLA NLA NLA NLA NLA NLA N/A NLA NLA NLA N/A NLA NLA NLA NLA N/A NLA NLA NLA N/A NLA NLA NLA NLA N/A NLA NLA NLA NLA 20" Deep NLA NLA NLA NLA NLA NLA 20

22 Captain Seat Assembly NOTE: Captain seats recline approximately degrees for semi recline backs and degrees for full recline back models. NOTE: Adjustable depths are 16, 17, and 18" deep for 18" wide seats and 18, 19, and 20" deep for 20" wide seats. NOTE: Recline release levers are standard on the right side. Left side release levers can be ordered as a special with a new captain seat. 21

23 Captain Seat Assembly NOTE: Captain seats recline approximately degrees for semi recline backs and degrees for full recline back models. NOTE: Adjustable depths are 16, 17, and 18" deep for 18" wide seats and 18, 19, and 20" deep for 20" wide seats. NOTE: Recline release levers are standard on the right side. Left side release levers can be ordered as a special with a new captain seat. Item Number Description All Grey Fabric All Grey Vinyl All Tan Vinyl 1 Backrest Extension Semi Recline NLA NLA 2 Headrest Extension Full Recline NLA Captain Seat 18" Wide Semi Recline NLA NLA NLA with Backrest Extension Captain Seat 18" Wide Full Recline NLA NLA NLA with Headrest Extension Captain Seat 20" Wide Semi Recline NLA NLA with Backrest Extension Captain Seat 20" Wide Full Recline with Headrest Extension NLA NLA NLA Hinge Bracket w/ Not Shown Lever Semi-Recline - Right See Note(s) A See Note(s) A See Note(s) A Hinge Bracket w/o Not Shown Lever Semi-Recline - Left See Note(s) A See Note(s) A See Note(s) A Screw, Phillips Not Shown Truss Head (1/4-20 x /4") See Note(s) B See Note(s) B See Note(s) B NOTE: A - Not Shown. Hinge Brackets used for ALL Semi-Recline Seat models only. For attaching Hinge Bracket, see part number B - Not shown, Screw for Hinge Bracket(s) and Total of (7) required for each Bracket. NOTE: When converting from a semi recline to a full recline captain seat, a sensor cable part # must be ordered as well. Actuator mounting hardware IS NOT included with a full recline captain seat. See actuator mounting hardware. 22

24 Captain Seat and Actuator Hardware 2

25 Captain Seat and Actuator Hardware Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Frame, Seat, Black (18" W) NLA NLA - Frame, Seat, Black (20" W) Spacer (1/4 x 5/8 x /8") Locknut (1/4-20) Screw, Hex Head (1/4-20 x 1-1/2") Spacer (1/4 x 5/8 x 1/4") Spacer, Coved (1/4 x 11/16 x 1/2") NLA NLA - Screw, Hex Head (1/4-20 x 2-1/4") Spacer (1/4 x /8 x /16") Screw, Hex Head (1/4-20 x 1-1/4") Washer (1/4 x 2/2 x 1/16") A NLA NLA - Hardware, Captain Seat Mounting NLA NLA - Washer, Internal Tooth Lock (#4-40) NLA NLA - Package, Screw, Phillips Pan Head (#4-40 x 25 4 /8") 14 P0870X000 Nut, Hex Keps (#4-40) Sensor, Actuator Switch B NLA NLA - Hardware, Actuator Switch Sensor Mounting 1 1 NOTE: A - Includes Items B - Includes Items

26 Back Canes, Spreader Bars and Attaching Hardware NOTE: Chairs manufactured with a seat width, seat depth or back height of 20" and greater will be equipped with a spreader bar standard. 25

27 Back Canes, Spreader Bars and Attaching Hardware NOTE: Chairs manufactured with a seat width, seat depth or back height of 20" and greater will be equipped with a spreader bar standard. Item Number Note Part Number Description Quantity Per Package Assembly 1 See Chart #1 Back Cane Assemblies See Chart #2 Spreader Bar Package, Foam Hand Grip (9" L) Package, Plug Button, Black (7/8") A,E NLA Kit, Back Cane Attaching Hardware, For CJ Bracket " Deep Seat 8 Insert, Non-Threaded Back Cane 1 2 (For Back Heights 20" and Lower) 10 Washer (1/4 x 2/2 x 1/16") Locknut (1/4-20) Spacer, Coved (1/4 x 11/16 x 1/2") NLA - Bracket, Back Mounting, Black - Right NLA - Bracket, Back Mounting, Black - Left Screw, Hex Head (1/4-20 x 1-5/8") B,C NLA NLA - Kit, Back Cane Attaching Hardware Locknut (5/16-24) Screw w/ Lug (5/16-24 x 1-/8") Insert, Non-Threaded Back Cane 1 2 (For Back Heights 20" and Lower) 9 Screw, Hex Head (1/4-20 x 1-5/8") Washer (1/4 x 2/2 x 1/16") Locknut (1/4-20) Spacer, Coved (1/4 x 11/16 x 1/2") B,D NLA NLA - Kit, Back Cane Attaching Hardware Locknut (5/16-24) Screw w/ Lug (5/16-24 x 1-/8") NLA - Insert, Non-Threaded Back Cane 1 2 (For Back Heights 21" and Higher) 9 Screw, Hex Head (1/4-20 x 1-5/8") Washer (1/4 x 2/2 x 1/16") Locknut (1/4-20) Spacer, Coved (1/4 x 11/16 x 1/2") 1 4 NOTE: A - Includes items 8 and B - Includes items 6-12 C - Used for 14"-20" high back canes D - Used for 21"-22" high back canes E - Prior to 7/9/04 new back cane attaching hardware must be ordered for 14"-15" deep seats that use CJ brackets. The threaded insert was replaced with a non-threaded insert for 14"-20" high back canes. 26

28 Back Canes, Spreader Bars and Attaching Hardware NOTE: Chairs manufactured with a seat width, seat depth or back height of 20" and greater will be equipped with a spreader bar standard. #1 Back Cane Assemblies Back Height Back Cane- No Push Handle 10 Deg. Bend Back Cane- Push Handle Straight 14" NLA NLA 15" NLA NLA 16" NLA " NLA " NLA " NLA " NLA " N/A N/A 22" N/A N/A NOTE: Back Cane Assemblies include Foam Grips and Plug Buttons where shown Back Cane- Push Handle 10 Deg. Bend NLA NLA NLA NLA #2 Spreader Bar Chair Width 14" 15" 16" 17" 18" 19" 20" Part Number NLA NLA

29 Back Upholstery 28

30 Back Upholstery Nylon Single Liners Back Width 12-1" H 14-15" H 16-17" H 18-19" H 20" H 21-22" H 2-24" H 14" Wide NLA NLA 15" Wide NLA NLA NLA 16" Wide NLA " Wide " Wide Nylon Dual Liners Back Width 16-17" H 18-19" H 20" H 21-22" H 2-24" H 14" Wide " Wide " Wide " Wide " Wide " Wide " Wide NOTE: Dual liner back upholstery is used with chairs that have a seat deeper than 17" or back wider than 18". NOTE: Specify upholstery colors, see page titled "Frame Finishes and Upholstery Colors" 29

31 Back Upholstery Nylon Back Upholstery Hardware Part Number Description 2 each - Screw with Washer (10 7/8") 2 each - Cable Ties Vinyl Single Liners Back Width 12-1" H 14-15" H 16-17" H 18-19" H 20" H 21-22" H 2-24" H 14" Wide NLA NLA NLA NLA NLA NLA 15" Wide NLA NLA NLA NLA NLA 16" Wide NLA NLA NLA NLA NLA NLA NLA 17" Wide NLA NLA NLA NLA NLA NLA 18" Wide NLA NLA NLA NLA NLA NLA Use Nylon Upholstery as a replacement for Vinyl selections that are No Longer Available. NOTE: Specify upholstery colors, see page titled "Frame Finishes and Upholstery Colors". 0

32 Back Upholstery Vinyl Dual Liners Back Width 16-17" H 18-19" H 20" H 21-22" H 2-24" H 14" Wide NLA NLA NLA NLA NLA 15" Wide NLA NLA NLA NLA NLA 16" Wide NLA NLA NLA NLA NLA 17" Wide NLA NLA NLA NLA NLA 18" Wide NLA NLA NLA NLA NLA 19" Wide NLA NLA NLA NLA 20" Wide NLA NLA NLA NLA NLA Use Nylon Upholstery as a replacement for Vinyl selections that are No Longer Available. NOTE: Dual liner back upholstery is used with chairs that have a seat deeper than 17" or back wider than 18". NOTE: Specify upholstery colors, see page titled "Frame Finishes and Upholstery Colors". Vinyl Back Upholstery Hardware Part Number Description 2 each - Screw with Washer (10 7/8") 2 each - Cable Ties 1

33 Captain Seat Arms and Hardware 18" Wide Models 2

34 Captain Seat Arms and Hardware 18" Wide Models Item Number Note Part Number Description Quantity Per Package Assembly 1 A Kit, Arm Pad w/ Screws, Full Length, Urethane 1 2 Waterfall, Black (1" L x 2-5/8" W) NLA NLA - Plate, Armrest (Black) Screw, Phillips Pan Head (#10-2 x 5/8") Screw, Socket Button Head (1/4-20 x 1") NLA NLA - Nut, Hex (1/4-20) Washer, Flat (5/16 x 5/8 x 1/16") Tube, Arm, Upper Height and Width Adjustable, 1 2 Black X01 Anti-Rattle (1") NLA NLA - Screw, Socket Head (1/4-20 x 1-1/4") NLA NLA - Locknut (5/16-24) NLA NLA - Screw, Phillips Pan Head (#10-2 x 7/8") Insert, Armrest, Black Screw w/ Lug (5/16-24 x 1-/8") B NLA NLA - Kit, Armrest Attaching Hardware (Pair) C NLA NLA - Kit, Arm Pad Attaching Hardware D NLA NLA - Arm Tube Assembly, Upper Adjustable (Pair) 2 1 NOTE: A - As of 1//02 upholstered waterfall armpads were replaced with black urethane waterfall armpads. Order in pairs for chairs manufactured before 1//02. B - Includes items 2, 4, 5, 6, 10, 1 C - Includes items, 11, 12 D - Includes items 7-9

35 Captain Seat Arms and Hardware 20" Wide Models 4

36 Captain Seat Arms and Hardware 20" Wide Models Item Number Note Part Number Description Quantity Per Package Assembly 1 A Kit, Arm Pad w/ Screws, Full Length, Urethane 1 2 Waterfall, Black (1" L x 2-5/8" W) NLA NLA - Plate, Armrest Screw, Phillips Pan Head (#10-2 x 5/8") Screw, Socket Button Head (1/4-20 x 1") NLA NLA - Nut, Hex (1/4-20) Washer, Flat (5/16 x 5/8 x 1/16") NLA NLA - Tube, Arm, Upper Adjustable, Black NLA NLA - Anti-Rattle Screw, Socket Head Cap w/ Patch (1/4-20 x 1-1/2") NLA NLA - Locknut (5/16-24) NLA NLA - Screw, Phillips Pan Head (#10-2 x 7/8") NLA NLA - Insert, Armrest, Black Screw w/ Lug (5/16-24 x 1-/8") B NLA NLA - Hardware, Armrest Attaching (Pair) C NLA NLA - Hardware, Arm Pad Attaching (Pair) D NLA NLA - Arm Tube Assembly, Upper Adjustable (Pair) 2 1 NOTE: A - As of 1//02 upholstered waterfall armpads were replaced with black urethane waterfall armpads. Order in pairs for chairs manufactured before 1//02. B - Includes items 2, 4, 5, 6, 10, 1 C - Includes items, 11, 12 D - Includes items 7-9 5

37 Arms, Adjustable Height 14-15" Deep Seat Frames 6

38 Item Number Note Part Number Description Arms, Adjustable Height 14-15" Deep Seat Frames Quantity Per Package Assembly 1 A Pad, Arm, Vinyl, Full Length - Right (14" L x 2" W) A Pad, Arm, Vinyl, Full Length - Left (14" L x 2" W) A Kit, Arm Pad w/ Screws, Full Length (14" L x 2" W) 2 1 (Pair) 1 A Pad, Arm, Vinyl, Desk Length (9" L x 2" W) A Kit, Arm Pad w/ Screws, Desk Length (9" L x 2" W) 2 1 (Pair) Arm Tube Assembly w/ Plug Buttons, Full Length, 1 1 Black - Right/Left Arm Tube Assembly w/ Plug Buttons, Desk Length, 1 1 Black - Right/Left Plug Button, Black (7/8") Package, Screw, Phillips Pan Head (#10-2 x /8") X074 Spring, Arm Lock Pin, Arm Lock, Black Kit, Lock Handle w/rivets (Pair) Plug, Pivot Plug Button, Black (5/8") Grip, Push Handle B Arm Base Assembly, Adjustable Height, Black Right 11 B Arm Base Assembly, Adjustable Height, Black - Left NLA NLA - Package, Locknut (1/4-20) Clevis, Pivot Screw, Socket Button Head (1/4-20 x 1-5/8") Pin, Pull C Kit, Swingaway Armrest Mounting Hardware 1 1 NOTE: A - Specify upholstery color when ordering. B - Includes items C - Includes items

39 Arms, Fixed Height 16-20" Deep Seat Frames 8

40 Item Number Note Part Number Description A 2 2 A B Arms, Fixed Height 16-20" Deep Seat Frames Quantity Per Package Assembly See Chart #1 Arms, Fixed Height - Arms Less Arm Pad " Deep Seat Frame 1 1 See Chart #1 Arms, Fixed Height - Arms Less Arm Pad - 20" 1 1 Deep Seat Frame Kit, Arm Pad w/ Screws, Full Length, Urethane 1 1 Waterfall, Black (1" L x 2-5/8" W) Kit, Arm Pad w/ Screws, Full Length, Urethane 2 1 Waterfall, Black (1" L x 2-5/8" W) (Pair) Kit, Arm Pad w/ Screws, Desk Length, Urethane 1 1 Waterfall, Black (9" L x 2-5/8" W) Kit, Arm Pad w/ Screws, Desk Length, Urethane 2 1 Waterfall, Black (9" L x 2-5/8" W) (Pair) Tube, Arm, Desk Length, Black - Right (16-19" D) NLA NLA - Tube, Arm, Desk Length, Black - Left (16-19" 1 1 D) NLA NLA - Tube, Arm, Desk Length, Long, Black - Right 1 1 (20" and Deeper) NLA NLA - Tube, Arm, Desk Length, Long, Black - Left 1 1 (20" and Deeper) Tube, Arm, Full Length, Black - Right (16-19"D) NLA NLA - Tube, Arm, Full Length, Black - Left ( "D) NLA NLA - Tube, Arm, Full Length, Long, Black - Right 1 1 (20" and Deeper) NLA NLA - Tube, Arm, Full Length, Long, Black - Left 1 1 (20" and Deeper) Grip, Foam Hand (9" L) Screw, Phillips Pan Head Tap (#8-2 x /8") NLA NLA - Guard, Clothing, Desk Length NLA NLA - Guard, Clothing, Full Length (16-19" D) NLA NLA - Guard, Clothing, Full Length (20" and 1 1 Deeper) Cover, Clothing Guard w/ Pocket, FXDESK & 1 1 ADJFULL/ADJDESK Cover, Clothing Guard with Pocket Fixed Height Full 1 1 Length (20" and Deeper) Package, Screw, Phillips Pan Head (#10-2 x /8") Package, Screw, Phillips Pan Head (#10-2 x /4") Plug, Pivot Plug Button, Black (5/8") NLA NLA - Package, Locknut (1/4-20) Clevis, Pivot Screw, Socket Button Head (1/4-20 x 1-5/8") 1 1 9

41 Item Number Note Part Number Description NOTE: Arms, Fixed Height 16-20" Deep Seat Frames Quantity Per Package Assembly Pin, Pull Kit, Swingaway Armrest Mounting Hardware 1 1 A - As of 1//02 upholstered waterfall armpads were replaced with black urethane waterfall armpads. Order in pairs with screws for chairs manufactured before 1//02. B - For Black Urethane, Waterfall Arm Pads only. #1 - Arms Less Arm Pad 16-19" Deep Seat Frame Arms Style Right Left Desk NLA NLA Full NLA NLA #1 - Arms Less Arm Pad 20" Deep Seat Frame Arm Style Right Left Desk Long NLA NLA Full Long NLA NLA 40

42 Arms, Adjustable Height 16-20" Deep Seat Frames 41

43 Item Number Note Part Number Description 1 A 1 1 A B Arms, Adjustable Height 16-20" Deep Seat Frames Quantity Per Package Assembly Kit, Arm Pad w/ Screws, Full Length, Urethane Waterfall, Black (1" L x 2-5/8" W) Kit, Arm Pad w/ Screws, Full Length, Urethane 2 1 Waterfall, Black (1" L x 2-5/8" W) (Pair) Kit, Arm Pad w/ Screws, Desk Length, Urethane 1 1 Waterfall, Black (9" L x 2-5/8" W) Kit, Arm Pad w/ Screws, Desk Length, Urethane 2 1 Waterfall, Black (9" L x 2-5/8" W) (Pair) Arm Tube Assembly w/ Plug Buttons, Full Length, 1 1 Black - Right/Left Arm Tube Assembly w/ Plug Buttons, Desk Length, 1 1 Black - Right/Left Plug Button, Black (7/8") Package, Screw, Phillips Pan Head (#10-2 x /8") Package, Screw, Phillips Pan Head (#10-2 x /4") Guard, Clothing X074 Spring, Arm Lock Pin, Arm Lock, Black Grip, Foam Hand (9" L) Kit, Lock Handle w/rivets (Pair) Rivet Plug, Pivot Plug Button, Black (5/8") Cover, Clothing Guard w/ Pocket, FXDESK & 1 1 ADJFULL/ADJDESK Pin, Pull Screw, Socket Button Head (1/4-20 x 1-5/8") Clevis, Pivot NLA NLA - Package, Locknut (1/4-20) Arm Base Assembly, Black - Right (16-19" D) Arm Base Assembly, Black - Left (16-19" D) Arm Base Assembly, Black - Right (20" and Deeper) Arm Base Assembly, Black - Left (20" and Deeper) Arm Base Assembly, 1" Lower, Black - Right 1 1 (16-19" D) Arm Base Assembly, 1" Lower, Black - Left (16-19" 1 1 D) NLA NLA - Arm Base Assembly, 1" Lower, Black - Right 1 1 (20" and Deeper) NLA NLA - Arm Base Assembly, 1" Lower, Black - Left 1 1 (20" and Deeper) Kit, Swingaway Armrest Mounting Hardware

44 NOTE: Arms, Adjustable Height 16-20" Deep Seat Frames A - As of 1//02 upholstered waterfall armpads were replaced with black urethane waterfall armpads. Order in pairs with screws for chairs manufactured before 1//02. B - For Black Urethane, Waterfall Arm Pads only. 4

45 Front Riggings Reference Chart AT5544, 60HD, 70NHD, and PW9 NOTE: Calf pads with attaching hardware not included on legrest. NOTE: Pivot/Slide tube ataching hardware not included. NOTE: Pivot/Slide tube and footplates do not include heel loops. See footrest and legrest accessories. Pivot/Slide Tubes Model Number 1651 AT Description Composite footplate with 9-7/8" curved pivot/slide tube. Adjustable angle footplate wtih 9-7/8" straight pivot/slide tube. Deluxe aluminum footplate with "L" style pivot/slide tube. Extra large footplate with "L" style pivot/slide tube. Upper Support Assemblies NOTE: Pivot/Slide tube and footplate are interchangeable with the support assemblies listed here. NOTE: Side AT HD 70NHD PW Right Left See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A A - Specify frame color when ordering, see page titled "Frame Finishes and Touchup Paints". Pivot/Slide Tube and Footplates Right Left " Wide " Wide " Wide " Wide AT " Wide AT " Wide

46 Front Riggings Reference Chart AT5544, 60HD, 70NHD, and PW9 NOTE: Calf pads with attaching hardware not included on legrest. NOTE: Pivot/Slide tube ataching hardware not included. NOTE: Pivot/Slide tube and footplates do not include heel loops. See footrest and legrest accessories. 2" Longer Pivot/Slide Tube and Footplates Side Right Left " Wide NLA " Wide " Wide " Wide AT " Wide AT " Wide " Longer Pivot/Slide Tube and Footplates Side Right Left " Wide NLA NLA " Wide " Wide " Wide Support Assemblies with Pivot/Slide Tube and Footplate NOTE: Side Right Left Support Assemblies AT See Note(s) A See Note(s) A A - Specify frame color when ordering, see page titled "Frame Finishes and Touch-up Paints". Pivot/Slide Tube & Footplate " Wide NLA NLA 45

47 Front Riggings Reference Chart 70ST Pivot/Slide Tube & Footplates NOTE: Pivot/Slide tube attaching hardware not included. NOTE: Pivot/Slide tube and footplates do not include heel loops. See footrest and legrest accessories. Model Number 1651 Description 1651 Composite footplate with 9-7/8" curved pivot/slide tube. Support Assembly NOTE: Pivot/Slide tube and footplates are interchangeable with the support assemblies listed here. NOTE: Side Right Left 70ST Tapered Upper Support See Note(s) A See Note(s) A A - Specify Frame Color when ordering, see page titled "Frame Color and Touch-up Paint". Pivot/Slide Tube & Footplates Side Right Left " Wide " Wide " Wide " Longer Pivot/Slide Tube & Footplates Side Right Left " Wide NLA " Wide " Wide

48 Front Rigging Hanger Assembly Pin, Sector and Cage Style NOTE: Front rigging hanger assemblies and seat pans share the same mounting hardware, see Seat Pan and Mounting Hardware page. 47

49 Front Rigging Hanger Assembly Pin, Sector and Cage Style NOTE: Front rigging hanger assemblies and seat pans share the same mounting hardware, see Seat Pan and Mounting Hardware page. Item Number Note Part Number Description Quantity Per Package Assembly 1 A Front Rigging Hanger Assembly w/ Sector Block, 1 1 Black - Right (12-21" D) 1 A Front Rigging Hanger Assembly w/ Sector Block, 1 1 Black - Left (12-21" D) 2 B Kit, Sector Block - Right B Kit, Sector Block - Left Screw, Hex Head w/ Patch (1/4-20 x 2") Washer (1/4 x 1/2 x 1/16") C NLA NLA - Hanger Assembly, Front Rigging, Pin Style, 1 1 Black - Right (12-21" D) 5 C NLA NLA - Hanger Assembly, Front Rigging, Pin Style, 1 1 Black - Left (12-21" D) Plug Button, Black (/4") NLA NLA - Hanger Assembly, Front Rigging, Cage Style, 1 1 Black - Right NLA nla - Hanger Assembly, Front Rigging, Cage Style, Black - Left 1 1 NOTE: A - Includes front rigging hanger and item 2 B - Includes sector block assembly and items and 4 C - Includes front rigging hanger and item 6 48

50 Footrest Support Assemblies Sector Style 49

51 Item Number Note Part Number Description Footrest Support Assemblies Sector Style Quantity Per Package Assembly 1 A,B,E Footrest Support Assembly, 60 Degree Heavy Duty, 1 1 Sector, Color - Right 1 A,B,E Footrest Support Assembly, 60 Degree Heavy Duty, 1 1 Sector, Color - Left 1 A,B,E Footrest Support Assembly, 70 Degree 1 1 Non-Tapered Heavy Duty, Sector, Color - Right 1 A,B,E Footrest Support Assembly, 70 Degree 1 1 Non-Tapered Heavy Duty, Sector, Color - Left 1 A,B,F Footrest Support Assembly, 70 Degree Tapered, 1 1 Sector, Color - Right 1 A,B,F Footrest Support Assembly, 70 Degree, Tapered, 1 1 Sector, Color - Left Screw, Socket Button Head (1/4-20 x 1-/4") 1 1 I Plug Button, Black (1") 1 1 I Plug Button, Black (1") Pivot, Footrest Locknut (1/4-20) Screw, Slotted Hex Washer Head (#10-2 x 5/8") Screw, Slotted Hex Washer Head w/ Patch (# x 1/2") Housing, Latch - Right Housing, Latch - Left Collar, Anti-Rattle Screw, Hex Head w/ Patch (1/4-20 x /4") H Spacer, Coved (1/4 x 11/16 x 1/2") G Insert, Threaded Screw, Hex Head (1/4-20 x 1-1/2") Nut, Hex with Nylon Cap (1/4-20) C,F Kit, Pivot/Slide Tube Mounting Hardware (Pair) D Kit, Pivot/Slide Tube Mounting Hardware (Pair) 1 1 NOTE: A - Specify frame color when ordering. B - Includes items 2-9. C - Includes items D - Includes items E - Uses Item Number, Plug button F - Uses Item Number, Plug button G - As of 8/15/0, the Threaded Insert was revised from to 5 Holes. Threaded Insert is Backward Compatible and does not require ordering in Pairs. H - Item 16 takes 2 per assembly I - See item #1 footnote E or F for Front Rigging Plug Button usage. 50

52 Cage Style Footrest 51

53 Item Number Note Part Number Description Cage Style Footrest Quantity Per Package Assembly NLA NLA - Hanger Assembly, Front Rigging, Cage Style, 1 1 Black - Right NLA nla - Hanger Assembly, Front Rigging, Cage Style, 1 1 Black - Left Nut, Hex with Nylon Cap (1/4-20) Spacer, Coved (1/4 x 11/16 x 1/2") Screw, Hex Head (1/4-20 x 1-1/2") Collar, Anti-Rattle B Insert, Threaded A NLA NLA - Hardware, Cage Style Footrest Mounting Guard, Impact (12" L) Strap, Calf w/ Hook and Loop (6" L) See Chart #10 Cage Style Footrest 1 1 NOTE: A - Includes Items 2-6. B - As of 8/15/0, the Threaded Insert was revised from to 5 Holes. Threaded Insert is Backward Compatible and does not require ordering in Pairs. #10 Cage Style Footrest Chair Width 14" 15" 16" 17" 18" 19" 20" Dimension "A" on Illustration 9" 10" 11" 12" 1" 14" 15" Part Number NLA NLA NLA NLA NLA NLA NLA 52

54 AT5544 Legerst Supports Sector Style 14-20" Wide Chairs 5

55 Item Number Note Part Number Description AT5544 Legerst Supports Sector Style 14-20" Wide Chairs Quantity Per Package Assembly Cover, Top Screw, Phillips Pan Head (#8-2 x /8") X000 Hex Nut (/8"-16) Washer, Nylon (25/64 x 7/8 x 1/2") X000-NLA NLA - Screw, Slotted Truss Head (/8-16 x 1-1/2") NLA NLA - Locknut (5/16-24) Bolt, Lug (5/16-24 x 1-/8") NLA NLA - Tube, Elevating Adjustable Support, Black Right NLA NLA - Tube, Elevating Adjustable Support, Black Left 8 A Tube, Elevating Adjustable Support, Color - Right A Tube, Elevating Adjustable Support, Color - Left Bracket, Legrest Pad Mounting, Black X002 Bracket, Release, Black Screw, Slotted Hex Washer Head (#10-2 x 5/8") Housing, Latch - Right Housing, Latch - Left Package, Screw, Slotted Hex Washer Head (# x 1/2") X001 Bar, Ratchet NLA NLA - Nut, Acorn (5/16-24) Pivot, Footrest Plug Button, Black (1") NLA NLA - Package, Button Head Cap Screw (1/4-20 x /4") 19 A Bracket, Legrest Support, Color - Right A Bracket, Legrest Support, Color - Left Ring, Snap NLA NLA - Washer, Nylon (5/16 x 11/16 x 1/16") Tip, Plastic, Black Spring, Release Cam, Legrest Handle, Release B Kit, Elevating Legrest Ratchet Hardware (Pair) 1 1 C,D NLA NLA - Instruction Sheet, Ratchet Kit 1 1 A,C Legrest Support Assembly, Sector, Color - Right 1 1 A,C Legrest Support Assembly, Sector, Color - Left 1 1 NOTE: A - Specify frame color when ordering. B - Includes Items 10, 14, 15, and C - Not Shown D - Item is no longer available from the Invacare Service Parts Department. Refer to the Invacare Website under "Product Literature Search". Enter the part number in the "Keywords" field and download a free PDF version copy. 54

56 Calf Pads and Attaching Hardware Due to a change to the Legrest Calf Pad size made on 4/2/12, you must also order the hardware kit ( ) when ordering replacement Calf Pads. Item Number Note Part Number Description Quantity Per Package Assembly 1 A,B,E Pad w/ Cover and Screws, Legrest Vinyl (Pair) A,B,E Pad, Legrest, Vinyl - Right/Left A,C,E X00 Pad, Legrest, Vinyl - Right A,C,E X004 Pad, Legrest, Vinyl - Left X019 Plate, Legrest Pad NLA NLA - Locknut (5/16-24) Spacer, Legrest Pad, Black Spacer, Legrest Pad Mounting, Black Screw, Hex Head (5/16-24 x -1/2") Screw, Hex Head (5/16-24 x 1-1/2") D Hardware, Legrest Pad 1 1 Screw, Phillips Pan Head (#10-2 x 11/16") 1 2 Screw, Phillips Pan Head (#10-2 x 1") 1 2 Instruction Sheet, Legrest Pad Mtg Bracket, Legrest Pad Mounting, Black 1 1 NOTE: A - Specify upholstery color, see page titled "Frame Finishes and Upholstery Colors". B - 16" - 20" Wide Chairs C - 14" - 15" Wide Chairs D - Includes Screws and Instruction Sheet. E - Due to a change to the Legrest Calf Pad size made on 4/2/12, you must also order the hardware kit ( ) when ordering replacement Calf Pads. 55

57 PW9 Footrest Supports Pin Style 56

58 Item Number Note Part Number Description PW9 Footrest Supports Pin Style Quantity Per Package Assembly Anti-Rattle, Black X057 Bushing (7/2 x /8 x 11/2") Screw, Phillips Pan Head (#10-2 x 11/16") Screw, Phillips Pan Head (#10-2 x 1/2") Handle, Release, Black - Right Handle, Release, Black - Left Locknut (#10-2) NLA NLA - Rivnut (#10-2) Spring, Release - Right Spring, Release - Left X012 Collar, Anti-Rattle (7/8") Screw, Hex Head (1/4-20 x 1-1/2") Spacer, Coved (1/4 x 11/16 x 1/2") Nut, Hex with Nylon Cap (1/4-20) D Insert, Threaded C Kit, Slide Tube Mounting Hardware 1 1 A,B Footrest Support Assembly, Adult, Color - Right 1 1 A,B Footrest Support Assembly, Adult, Color - Left 1 1 NOTE: A - Specify frame color when ordering. B - Not Shown C - Includes items D - As of 8/15/0, the Threaded Insert was revised from to 5 Holes. Threaded Insert is Backward Compatible and does not require ordering in Pairs. 57

59 Pivot/Slide Tube and 1651 Composite Footplates NOTE: Heel loops are not included. See Footrest and Legrest Accessories. NOTE: For complete pivot/slide tube and footplate assemblies, see Front Rigging Reference Charts. Item Number Note Part Number Description Quantity Per Package Assembly Tube, Pivot/Slide, Curved End, Steel, Black (9-7/8") Tube, Pivot/Slide, Curved End, 2" Longer, Steel, 1 1 Black Tube, Pivot/Slide, Curved End, 4" Longer, Steel, 1 1 Black Spacer, Coved (1/4 x /4 x 11/2") Plug Button, Black (/4") NLA NLA - Package, Locknut (1/4-20) Package, Socket Head Screw (1/4-20 x 2-1/4") A Footplate, Composite, Small, Black (6" W x 6" L) B Footplate, Composite, Medium, Black (7" W x 6" L) C Footplate, Composite, Large, Black (8" W x 6" L) 1 1 NOTE: A - Chairs 14" Wide or 70STAPER and PW9ST Only 15-17" Wide. B - Chairs 15-16" Wide or 70STAPER and PW9ST Only 18-19" Wide. C - Chairs 17" and Wider or 70STAPER and PW9ST Only 20" and Wider. 58

60 Pivot/Slide Tube and 1650, 1450, 150 Aluminum Footplates NOTE: Heel loops are not included. See Footrest and Legrest Accessories. NOTE: For complete pivot/slide tube and footplate assemblies, see Front Rigging Reference Charts. 59

61 Pivot/Slide Tube and 1650, 1450, 150 Aluminum Footplates NOTE: Heel loops are not included. See Footrest and Legrest Accessories. NOTE: For complete pivot/slide tube and footplate assemblies, see Front Rigging Reference Charts. Item Number Note Part Number Description Quantity Per Package Assembly Plug Button, Black (/4") Pivot/Slide Tube w/ Plug Button, Black Pivot/Slide Tube w/ Plug Button, Black (2" Longer) Pivot/Slide Tube w/ Plug Button, Black (4" Longer) NLA NLA - Pivot/Slide Tube w/ Plug Button, Deluxe, 1 1 Black 44200X059 Footplate, Aluminum, Small, Black (6-/4" W x 6" L) X027 Footplate, Aluminum, Medium, Black (7-/4" W x 6" 1 1 L) NLA NLA - Footplate, Aluminum, Deluxe, Black - Right 1 1 (8" W x 5-/4" L) NLA NLA - Footplate, Aluminum, Deluxe, Black - Left (8" 1 1 W x 5-/4" L) 44200X025 Footplate, Aluminum, Extra Large, Black - Right (8" 1 1 W x 8-1/2" L) 44200X026 Footplate, Aluminum, Extra Large, Black - Left (8" W 1 1 x 8-1/2" L) Cap, End, Tube, Black (7/8") Plug Button, Black (7/8") Spring, Tension NLA NLA - Spring B Spring, Leaf A NLA NLA - Package, Phillips Head Screw (#8-2 x /8") Plug, Push, Footplate 1 1 NOTE: A - Deluxe takes quantity (1). B - Use one or more leaf springs per assembly as required such that footplate may be moved by hand to the up-right position and remain in place. 60

62 AT554 Adjustable Angle Footplates 60deg HD, 70deg NHD, PW9, AT5544 Swingaway Supports NOTE: Heel loops are not included. See Footrest and Legrest Accessories. NOTE: For complete pivot/slide tube and footplate assemblies, see Front Rigging Reference Charts. 61

63 AT554 Adjustable Angle Footplates 60deg HD, 70deg NHD, PW9, AT5544 Swingaway Supports NOTE: Heel loops are not included. See Footrest and Legrest Accessories. NOTE: For complete pivot/slide tube and footplate assemblies, see Front Rigging Reference Charts. Item Number Note Part Number Description Quantity Per Package Assembly 1 A See Chart Footplate Assemblies w/ Pivot Slide Tubes B,D Footplate, Adjustable Angle, Large, Black (5-1/4" W 1 1 x 8" L) 2 C,D Footplate, Adjustable Angle, Extra Large, Black 1 1 (6-1/4" W x 8" L) Clamp, Footplate Tube, Pivot and Slide, Straight, Steel, Black (9-7/8" 1 1 L) Tube, Pivot/Slide, Straight, Steel, Black (11-7/8" L) Screw, Nylon Adjustment (1/2-1 x 7/8") Hinge, Footplate - Right Hinge, Footplate - Left Screw, Socket Flat Head (1/4-20 x /4") Nut, Barrel, Hex Head (1/4-20 x 11/16") NLA NLA Package, Screw, Socket Button Head (1/4-20 x /8") Spacer, Coved (1/4 x /4 x 11/2") Washer (1/4 x 2/2 x 1/16") Package, Washer, Nylon (5/16 x 7/8 x 1/8") Washer (1/4 x 1/2 x 1/16") Locknut (1/4-20) 25 1 NOTE: A - Includes items 2 thru 14. B - For 14-15" wide chairs C - For 16" and wider chairs D - This footplate was revised 9/2/2008 with rounder corners and accessory holes changed from 8 to 4. Recommended to replace the footplate in pairs to match sides. #1 Footplate Assemblies w/ Pivot Slide Tubes Rigging Type Swingaway Supports (9-7/8" Pivot/Slide Tube) See Note(s) A Swingaway Supports (11-7/8" Pivot/Slide Tube) 14-15" W 5-1/4" Large Footplate - Right " W 5-1/4" Large Footplate - Left " and Wider 6-1/4" X-Large Footplate - Right See Note(s) B NOTE: A - 60 Deg. HD, 70 Deg. NHD, PW9, AT5544 Swingaway Supports w/ 9-7/8" Long Pivot/Slide Tubes B - 60 Deg. HD, 70 Deg. NHD, PW9, AT5544 Swingaway Supports w/ 11-7/8" Long Pivot/Slide Tubes 16" and Wider 6-1/4" X-Large Footplate - Left

64 Footrest and Legrest Accessories Item Number Note Part Number Description NOTE: Quantity Per Package Assembly Strap, Calf w/ Hook and Loop (6" L) 1 1 D H-Strap (24" L) E H-Strap (26" L) 1 1 F H-Strap (1" L) 1 1 A Guard, Impact (8" L) 1 2 B Guard, Impact (12" L) 1 2 C See Chart Footrest and Legrest Accessories (Not Including 1 1 AT554) C See Chart Heel Loop Attaching Hardware (Not Including 1 1 AT554) C See Chart AT554 Adjustable Angle Heel Loops and Hardware 1 1 C See Chart Attaching Hardware - AT554 Footplates w/ Toe 1 1 Loops C See Chart Toe Loops C See Chart Attaching Hardware , 1650, 1450 and 150 Footplates w/ Toe Loops 1 1 A - For 70 deg. Tapered Footrest B - For Cage Style Footrest C - Not Shown D - 14" wide seats E " wide seats F - 17" and wider seats Footrest and Legrest Accessories (Not Including AT554) Footplate Type Composite (1651) Small 14" Wide or 15-17" Wide Tapered Composite (1651) Medium 15-16" Wide or 18-19" Wide Tapered Composite (1651) Large 17-20" Wide or 20" Wide Tapered Heel Loop Single # NLA Heel Loop Pair # NLA Heel Loop with Ankle Strap Single # Right NLA NLA Heel Loop with Ankle Strap Single # Left NLA NLA Heel Loop with Ankle Strap Pair # Attaching Hardware Pair #

65 Footrest and Legrest Accessories Footrest and Legrest Accessories (Not Including AT554) Footplate Type Standard Aluminum (1650) 14-15" Wide Standard Aluminum (1650) 16-20" Wide Deluxe Aluminum (1450) 16-20" Wide X-Large Aluminum (150) 16-20" Wide Heel Loop Single # NLA Heel Loop Pair # Heel Loop with Ankle Strap Single # Right NLA Heel Loop with Ankle Strap Single # Left NLA Heel Loop with Ankle Strap Pair # Attaching Hardware Pair # NLA Heel Loop Attaching Hardware (Not Including AT554) Part Number Description Consist of: (2) Screw, Phillips, Pan Head (1/4-20 x 2-1/4") NLA Kit, Heel Loop Attaching Hardware (Pair) Kit, Heel Loop Attaching Hardware (Pair) Hardware, Attaching (Pair) NLA - Hardware, Attaching (Pair) (2) Spacer (1/4 x 11/2 x 1-/4") (2) Hex Nut w/ Nylon Cap (1/4-20) (2) Flat Washer (1/4 x 5/8 x 1/16") (2) Screw, Phillips Head (1/4-20 x 2-1/2") (2) Spacer (1/4 x 11/2 x 1-/4") (2) Locknut (1/4-20) (2) Screw, Phillips Head (1/4-20 x 2-1/4") (2) Spacer (1/4 x 11/2 x 1-/4") (2) Locknut (1/4-20) (2) Screw, Phillips Head (1/4-20 x 2-1/2") (2) Spacer (1/4 x 11/2 x 1-/4") (2) Locknut (1/4-20) 64

66 Footrest and Legrest Accessories 65

67 Footrest and Legrest Accessories AT554 Adjustable Angle Heel Loops and Hardware Part Number Description Consist of: (2) Heel Loops Attaching Hardware Only Kit, Heel Loop w/ Hardware, Adjustable Angle Footplate (Pair) Kit, Heel Loop w/ Ankle Strap and Hardware, Adjustable Angle Footplate (Pair) Kit, Heel Loop Attaching Hardware (Pair) (4) Screw, Phillips Pan Head (1/4-20 x 2-1/4") (4) Spacer (4) Locknut (1/4-20) (2) Heel Loops w/ Ankle Strap (4) Screw, Phillips Pan Head (1/4-20 x 2-1/4") (4) Spacer (4) Locknut (1/4-20) (2) Screw, Phillips, Pan Head (1/4-20 x 2-1/4") (2) Spacer (1/4 x 11/2 x 1-/4") (2) Hex Nut w/ Nylon Cap (1/4-20) (2) Flat Washer (1/4 x 5/8 x 1/16") Toe Loops 145 Part Number 04572X Description Toe Loop (Single) Toe Loops without Hardware (Pair) Attaching Hardware - AT554 Footplates w/ Toe Loops Part Number Description Consist of: Hardware, Toe Loops and Footplate (Pair) (4) Screw, Phillips Pan Head (#10-2 x 1/2") (4) Locknut (#10-2) Attaching Hardware , 1650, 1450 and 150 Footplates w/ Toe Loops Part Number Description Consist of: 66

68 Footrest and Legrest Accessories Attaching Hardware , 1650, 1450 and 150 Footplates w/ Toe Loops Part Number Description Consist of: Hardware, Toe Loop (Pair) (4) Screw, Phillips Pan Head (#10-2 x 7/8") (4) Washer (1/4 x /4 x /2") (4) Locknut (#10-2) 67

69 Front Riggings - Adjustable Heel Loops 68

70 Front Riggings - Adjustable Heel Loops Item Number Note Part Number Description Quantity Per Package Assembly 1 A Kit, Heel Loop, Adjustable w/ Hardware (Pair) Heel Loop 1 2 NLA - Spacer (1/4 x 11/2 x 1-/4") NLA - Screw, Phillips Pan Head (1/4-20 x 2-1/4") Washer, Flat (1/4 x 5/8 x 1/16") Nut, Hex, Nylon Cap (1/4-20) 1 2 Instruction Sheet, Adjustable Heel Loop B Kit, Heel Loop, Adjustable w/ Hardware, Deluxe (Pair) 2 Heel Loop 1 2 NLA - Spacer (1/4 x 11/2 x 1-/4") Nut, Hex, Nylon Cap (1/4-20) NLA - Screw, Phillips Pan Head (1/4-20 x 2-1/2") 1 2 Instruction Sheet, Adjustable Heel Loop 1 1 NOTE: A - Kit includes items 2-6. Used with All Footplates except Deluxe (1450). B - Kit includes items 2,, 6, and item 7. Used with Deluxe (1450) Footplates only. 69

71 Base Frame, Suspension Arms, and Torsion Bar 70

72 Base Frame, Suspension Arms, and Torsion Bar Item Number Note Part Number Description Quantity Per Package Assembly X006 Bearing (5/8") NLA NLA - Bearing (/8") NLA NLA - Pin, Shoulder (/8 x 1-/8") Locknut (5/16-18) NLA NLA - Plug Button, Frame, Black Decal, Invacare -D Logo (2-1/2" L) NLA NLA - Plate, Name, Patent Numbers A,D Frame Assembly with Insert, Color Bearing, Flange (/4") NLA NLA - Bumper, Rubber (1" Diameter x 5/8") X006 Bearing (5/8") NLA NLA - Decal, Xterra GT B,D NL NLA - Arm Suspension - Right 1 1 A 1 B,D NL NLA - Arm Suspension - Left 1 1 A Washer, Flat (5/16 x 5/8 x 1/16") NLA NLA - Flange (5/16" I.D.) NLA NLA - Bar, Torsion, Black NLA NLA - Clip, Pin Hitch (/2 x 1-5/8") C NLA NLA - Torsion Bar Assembly, Black Ring, Tolerance 1 2 NOTE: A - Includes Base Frame and Items 1-7 and 19. B - Includes Items 9-12 and 19. C - Includes Items D - Specify frame color when ordering. 71

73 Suspension Arm Mounting Hardware Item Number Note Part Number Description Quantity Per Package Assembly Washer, Flat (5/16 x 5/8 x 1/16") Locknut (5/16-18) Locknut (1/2-20) NLA NLA - Washer, Steel (1-/16 x 1/2 x 1/8") Pin, Pivot NLA NLA - Screw, Hex Head (5/16-18 x -/4") A NLA NLA - Hardware, Suspension Arm Mounting 2 1 NOTE: A - Includes Items

74 Front Suspension Spring Mounting Hardware Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Spacer, Spring, Black NLA NLA - Spring, Compression NLA NLA - Retainer, Spring NLA NLA - Retainer, Lower Spring A NLA NLA - Hardware, Front Suspension Spring Mounting 2 1 NOTE: A - Includes items 1-4 7

75 4-Pole Motor and Gearbox Assembly Item Number Description Right Left Motor/Gearbox Assembly Gear Box Motor Assembly Coupling w/ Cup (1-5/16" Diameter) Lockwasher (1/4") Screw, SHC (M6 x 1 x 20MM) Screw, SHC (1/4-20 x 1-1/8") Brushes with Caps Cap, Brake Lever End Slotted Plate Brake Repair Kit Brake Cover with Screws See Note(s) A NLA See Note(s) D See Note(s) B 50000X X See Note(s) D See Note(s) D See Note(s) F NLA NLA See Note(s) G See Note(s) A NLA See Note(s) D See Note(s) B 50000X X See Note(s) D See Note(s) D See Note(s) F NLA NLA See Note(s) G

76 4-Pole Motor and Gearbox Assembly NOTE: Item Description Right Left Number Screw, Phillips Pan Head NLA NLA 12. (M4 x.7 x 8 mm) See Note(s) H See Note(s) H 1. Motor Mount NLA NLA Screw, Socket w/ Patch (M6 x 20) See Note(s) E Screw, Socket w/ Patch (M6 x 5) NLA - Kit, Motor Mounting NLA NLA 16. Hardware See Note(s) C See Note(s) C A - Includes items B - Includes items C - Includes items 14 and 15. D - When a new gearbox or mounting screws are ordered, (2 ea.) metric and (2 ea.) non-metric screws (item 9) must be ordered. Invacare Corp. utilizes alternate suppliers for this part number. E - The Kit comes with a quantity of Screws, the drawing only shows a quantity of 2. F - Kit includes (4) Brushes, (4) Brush Caps and Instruction Sheet. G - Use existing screws when installing the Brake Repair Kit. The Motor Brake Mounting Screws are not saleable. H - No longer available, use as the replacement part. 75

77 Front 8" and Rear 6" Caster Assembly NOTE: Front and rear caster assemblies use the same caster fork mounting hardware. 76

78 Front 8" and Rear 6" Caster Assembly NOTE: Front and rear caster assemblies use the same caster fork mounting hardware. Item Number Note Part Number Description Quantity Per Package Assembly Cap, End, Tube, Black Locknut (5/8-18) Washer, Nylon (5/8 x 1-5/16 x 1/8") A NLA NLA - Hardware, Caster Fork Mounting NLA NLA - Fork, Front - Right NLA NLA - Fork, Front - Left NLA NLA - Fork, Rear Caster - Right NLA NLA - Fork, Rear Caster - Left Pin, Cotter (7/64 x 1") Screw, Phillips Flat Head (M6 x 1 x 45mm) Spacer, Steel (5/8 x 7/8 x 1/8") Washer, Steel (15/2 x 5/8 x /64") NLA NLA - Nut, Hex Slotted (7/16-20) Locknut (M6 x 1) B Hardware, Caster X006 Bearing (5/8") Bearing (7/16") Cap, Hub, Black C,F NLA NLA - Rim (Outer/Inner) with Hardware Wheel Assembly, Semi-Pneumatic, Front (8" x /4") 17 D NLA NLA - Wheel Assembly, Semi-Pneumatic, Rear (6" x 1 1 2") 17 E Wheel Assembly, Semi-Pneumatic, Urethane, Deep 1 1 Profile, Grey Tire/Black Hub (6" x 2") 17 E Wheel Assembly, Semi-Pneumatic, Urethane, Deep Profile, Grey Tire/Black Hub (6" x 2") (Pair) 2 1 NOTE: A - Includes Items 1-. B - Includes items C - Includes items 7 and 11. D - For chairs made before 7/14/0, order (pair) part number dated after 7/1/0 so each side matches. The deep profile caster design has two tread grooves with rounded corners instead of four tread grooves with square corners. E - For chairs made after 7/1/0. The pair part number is also used for converting casters on chairs made before 7/14/0. F - Rim is no longer available, see item

79 16" Drive Wheel and Mounting Hardware 78

80 16" Drive Wheel and Mounting Hardware Item Number Note Part Number Description Quantity Per Package Assembly 1 C NLA NLA - Wheel Assembly, Pnuematic w/flat Free 1 1 Insert (16" x ") 1 C NLA NLA - Wheel Assembly, Pneumatic (16" x ") Tire w/ Foam Fill Insert, Grey (16" x ") NLA NLA - Tire, Pneumatic, Grey (16" x ") NLA NLA - Tube, Pneumatic NLA NLA - Kit, Rim 10 x " w/ Screws (For 16 x " 1 1 Wheel) A Screw, Socket Head w/ Patch (5/16-18 x 7/8") Hub, Wheel Key (/16 x 1-1/4") Washer (1/2 x 1-9/2 x 1/8") Locknut (1/2-20) NLA NLA - Spring, Hub Cap Locknut (5/16-24) NLA NLA - Cap, Hub (16" Wheel) B NLA NLA - Hardware, Wheel Mounting (16") 1 1 NOTE: A - Part may be ordered individually or is included in Part # B - Includes Items C - Includes items 2 and. 79

81 Fenders and Shrouds 80

82 Item Number Note Part Number Description Fenders and Shrouds Quantity Per Package Assembly Screw, Phillips Pan Head Tap (#10-2 x 1/2") NLA NLA - Plate, Fender NLA NLA - Fender - Right NLA NLA - Fender - Left A Fender Assembly Screw, Phillips Pan Head Tap (#10-2 x 1/2") Washer, Flat (/16 x 5/8 x 1/16") B NLA NLA - Hardware, Shroud Mounting NLA NLA - Decal, Invacare Medallion - Large NLA NLA - Shroud, Rear C NLA NLA - Shroud with Decal, Front with Charger Port 1 1 Plugs 10 D NLA NLA - Shroud with Decal 1 1 Front without Charger Port Plugs NLA NLA - Plug Button, Black (1") 1 2 NOTE: A - Includes Items 1-. B - Includes Items 5 and 6. C - MKIV RII Controller D - MKIV Quad Pulse Controller 81

83 Battery Charger and Harness 82

84 Item Number Note Part Number Description Battery Charger and Harness Quantity Per Package Assembly Charger, Battery, 8 Amp, 115vac, Off Board 1 1 Dual Mode Round Plug, Lester 1 F Charger, Battery, 8 Amp. 115vac (Off Board) 1 1 Single Mode Round Plug w/ AC Power Line Cord 1 F E-NLA NLA - WARR RPLMT - Charger, Battery, 8 Amp, VAC (Off Board) Single Mode Round Plug w/ AC Power Line Cord Fuse - Buss Mini ATM-15 (15 AMP) NLA NLA - Package, Tie Wrap (-7/8" L) NLA NLA - Wrap, Slit Wire Harness (1/2" O.D., 6" Long 1 1 Cut To Length) 5 D NLA NLA - Fuse, Buss ATC-20 (20 AMP) E NLA NLA - Fuse - Buss Mini ATM-20 (20 AMP) A NLA NLA - Harness, Wiring B NLA NLA - Harness, Wiring NLA NLA - Cable, Programmer Extension (9" L) C NLA NLA - Cable, Drive Lockout Sensor G NLA NLA - Cord, AC Power, 115VAC, 2 Prong Off-Board 1 1 (11' 6" L) Cord, AC Power, 115VAC, Prong On-Board (6' 6-1/2" L) 1 1 NOTE: A - For MKIV Quad Pulse Controller. B - For MKIV RII 80 AMP Controller. C - Sensor cable is used with a full recline captain seat. D - Before 4/1/0 E - After /1/0 F - CTE charger introduced and standard on-chair 4/1/04. Used on Gel Cell or AGM (Absorbed Glass Mat) batteries. Serial number starts with 04A For wet cell batteries refer to the Lester charger. G - No longer available as a service part. Please use as its replacement. 8

85 Battery Top Cover and Tray Assembly 84

86 Battery Top Cover and Tray Assembly Item Number Note Part Number Description Quantity Per Package Assembly Bushing, Flange NLA NLA - Screw, Hex Head (5/16-18 x 1-/4") Washer, Steel (5/16 x /4 x 1/16") NLA NLA - Locknut (5/16-24) Washer, Flat (5/16 x 5/8 x 1/16") NLA NLA - Screw, Hex Head (5/16-24 x 8-1/2") Locknut (5/16-18) A NLA NLA - Hardware, Battery Tray Mounting NLA NLA - Strap and Buckle Assembly, Battery Tray NLA NLA - Grommet, Rubber B NLA NLA - Bracket, Port, Black Locknut (5/16-18) NLA NLA - Rod, Spade NLA NLA - Lug, Hex - Front NLA NLA - Rivet, Nylon NLA NLA - Cover, Splash NLA NLA - Cable, Programmer Extension (9" L) NLA NLA - Screw, Socket Button Head w/ Patch (# x 1/2") 19 B,C NLA NLA - Battery Tray Assembly D,F NLA NLA - Battery Tray Assembly NLA NLA - Top Cover Assembly, Battery NLA NLA - Strap with Clip Assembly, Battery Top Cover NLA NLA - Decal, Warning 1 1 E Fuse, MIDI (Non-G/B & G/B) (80 AMP) 1 1 E NLA NLA - Hardware, Terminal, 22NF Batteries Hardware includes: battery clamps, battery clamp caps (red and black), small terminal covers (red and black), 1/4-20 x 7/8" hex flange screws, 1/4-20 hex flange locknuts, cable ties, and instruction sheet for two batteries. 1 1 NOTE: A - Includes Items 1-7. B - For MKIV Quad Pulse Controllers Only. C - Includes Items D - Includes Items 9, 10, 12-14, and 18. E - Not Shown F - For MKIV RII Controllers Only. 85

87 MKIV Joysticks RII, TCHJOY, A, A+ 86

88 MKIV Joysticks RII, TCHJOY, A, A+ Item Number Description RII TCHJOY A A+ See Pictorial Joystick NLA Assembly See Note(s) D NLA NLA NLA 1 Knob, Joystick N/A Skirt, Joystick N/A Inductive, NLA NLA NLA N/A Joystick See Note(s) A See Note(s) B See Note(s) A Inductive, NLA N/A N/A Joystick See Note(s) C N/A 4 Boot, Joystick 50000X64-NLA N/A 50000X64-NLA 50000X64-NLA 5 Overlay, Joystick Decal N/A N/A NLA NLA 6 Cable NLA NLA N/A N/A Assembly See Note(s) B See Note(s) A 6 Cable NLA N/A N/A Assembly See Note(s) C N/A 7 Potentiometer, NLA NLA N/A Speed See Note(s) A See Note(s) B N/A 7 Potentiometer, NLA N/A N/A Speed See Note(s) C N/A 8 Knob, Potentiometer NLA NLA NLA N/A 9 Switch, On/Off N/A N/A Momentary See Note(s) B See Note(s) A 9 Switch, On/Off NLA N/A N/A Momentary See Note(s) C N/A 10 Switch, NLA N/A N/A N/A Program See Note(s) A 11 Switch, Toggle SPDT See Note(s) A N/A N/A N/A 12 Decal, RII 80 AMP NLA N/A N/A N/A NOTE: A - Item requires soldering B - Before 10/01/02 item requires soldering C - After 9/0/02 item has a non-soldering connector D - RII 80 amp. decal is not included with joystick. Used on Torque SP's after 10/1/01. 87

89 MKIV Joysticks PSF and PSR NOTE: PSR STANDARD joystick configuration below show the on/off switch on the left side for part # When the on/off switch is required on the right side, refer to part number and order as a configurated part. 88

90 MKIV Joysticks PSF and PSR NOTE: PSR STANDARD joystick configuration below show the on/off switch on the left side for part # When the on/off switch is required on the right side, refer to part number and order as a configurated part. Item Number Description PSF PSR See Pictorial Joystick Assembly N/A NLA See Pictorial Joystick Assembly NLA See Pictorial Joystick Assembly N/A NLA See Pictorial Joystick Assembly N/A NLA See Pictorial Joystick Assembly N/A NLA 1 Knob, Joystick Skirt, Joystick Inductive, Joystick NLA NLA 4 Boot, Joystick 50000X64-NLA 50000X64-NLA 5 Overlay, Joystick Decal NLA NLA 6 Cable Assembly NLA NLA 7 Potentiometer, Speed NLA NLA 8 Knob, Potentiometer NLA NLA 9 Switch, On/Off Momentary Switch, Push Button SPST Momentary NLA NLA 11 Switch, Push Button SPST N/A NLA 12 Boot, Switch NLA NLA 1 Boot, Switch NLA NLA 89

91 MKIV Joystick Mounting Hardware and Joystick Accessories 90

92 MKIV Joystick Mounting Hardware and Joystick Accessories Item Number Note Part Number Description Quantity Per Package Assembly 1 A NLA NLA - Kit, Straight Joystick Tube with Hardware B Kit, 1/2" Offset Joystick Tube with Hardware 1 1 C Plug Button, Black (7/8") Screw, Phillips Pan Head (#4-40 x /8") NLA NLA - Package, Tie Wrap (11-1/2" L) Spacer, Joystick Tube, Black Screw, Phillips Pan Head (#10-2 x 1-1/8") Clamp, Fixed Height Joystick Tube E,F NLA NLA - Kit, Joystick Tube Mounting Hardware Captain/ Van Seat Locknut (1/4-20) NLA NLA - Spacer (1/4 x 7/16 x 5/8") Clamp Assembly, Fixed Height, Captain/ Van Seat Screw, Hex Head (1/4-20 x 1-1/4") NLA NLA - Kit, Toggle Switch Extension 1 1 D Extension, Joystick, "T" Style (1560) 1 1 (4" W x 5-1/2" L) D Extension, Joystick, Straight Style (1561) 1 1 (1/2" W x 5" L) 15 G Clamp, Height Adjustable Joystick Tube (ARM250) 1 1 NOTE: A - For TCHJOY Touchpad "A" Joystick. Includes Items and 4 B - For MKIV, RII, A, A+, PSF/PSR Joysticks. Captain Seats also. Includes Items and 5-7 C - Touchpad "A" Joystick tube takes 2. D - Not Shown E - Includes items 10-1 F - Due to product improvement, the joystick mounting bracket with a separate adjustment lock were replaced with the clamp assembly shown as of 2/20/0 and is backward compatible. G - Can be used to replace a Fixed Height Joystick Tube Clamp in the field 91

93 MKIV Swivel Joystick Hardware Item Number Note Part Number Description Quantity Per Package Assembly Spacer, Joystick Tube, Black NLA NLA - Package, Screw, Phillips Pan Head (#10-2 x /8") NLA NLA - Bracket, Swivel Joystick, MKIV A NLA NLA - Bracket, Swivel Joystick with Hardware B NLA NLA - Joystick Swivel Tube with Hardware, Black NLA NLA - Washer, Flat (1/4 x /8 x 1/16") NLA NLA - Bushing NLA NLA - Spring, Hitch Bracket NLA NLA - Knob, Clamping, Grey NLA NLA - Tube, Swivel Joystick, Black Plug Button, Black (7/8") 1 1 NOTE: A - Includes items 1-. B - Includes items

94 MKIV Mid-Line Swing Bracket Assembly NOTE: Joystick tube with a 90 degree bend replaces the standard tube when joysticks PSF, PSR, and RII part# are used. Joystick tubes with a 90 degree bend must be ordered as a special when a replacement is needed. 9

95 MKIV Mid-Line Swing Bracket Assembly NOTE: Joystick tube with a 90 degree bend replaces the standard tube when joysticks PSF, PSR, and RII part# are used. Joystick tubes with a 90 degree bend must be ordered as a special when a replacement is needed. Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Tube, Adjustment, Inside, Mid-Line, Black NLA NLA - Spring, Extension (9/16 x 1-/8" L) NLA NLA - Tube, Adjustment, Outside, Mid-Line, Black Adjustment Lock Assemnbly, Black A NLA NLA - Swing Bracket Assembly, Mid-Line, Black NLA NLA - Screw, Hex Head (1/4-20 x 1-1/8") Adjustment Lock Assemnbly, Black B NLA NLA - Bracket, Joystick Mounting, Black Half Clamp, Non-Threaded Holes NLA NLA - Half Clamp, Threaded Holes B,C NLA NLA - Hardware, Attaching - Mid-Line 1 1 NOTE: A - Includes Items 1-4. B - Left side joystick mounting bracket or hardware must be ordered as a special. C - Includes Items

96 Quad Link Assembly Before 4/07/06 95

97 Item Number Note Part Number Description 1 A A B,E B Quad Link Assembly Before 4/07/06 Quantity Per Package Assembly NLA NLA - Kit, Quad Link Assembly - Right 1 1 NLA - Ball Plunger Assembly with Lock Washer 2 1 Locknut (#10-2) 1 2 NLA - Screw, Cap, Socket Head (#10-2 x 1/2") 1 4 NLA - Bushing, Bronze (/16 x 1/4 x 1/4") 1 4 Screw, Phillips Pan Head (#10-2 x 1-1/8") 1 4 Spacer, Joystick Tube, Black 1 1 NLA - Stud Plate, Quad Link 1 1 Screw, Hex Head (1/4-20 x 1-1/2") 1 Spacer (1/4 x /8 x /16") 1 Half Clamp, Non-Threaded Holes 1 1 NLA - Half Clamp, Threaded Holes NLA NLA - Kit, Quad Link Assembly - Left 1 1 NLA - Ball Plunger Assembly with Lock Washer 2 1 Locknut (#10-2) 1 2 NLA - Screw, Cap, Socket Head (#10-2 x 1/2") 1 4 NLA - Bushing, Bronze (/16 x 1/4 x 1/4") 1 4 Screw, Phillips Pan Head (#10-2 x 1-1/8") 1 4 Spacer, Joystick Tube, Black 1 1 NLA - Stud Plate, Quad Link 1 1 Screw, Hex Head (1/4-20 x 1-1/2") 1 Spacer (1/4 x /8 x /16") 1 Half Clamp, Non-Threaded Holes 1 1 NLA - Half Clamp, Threaded Holes NLA Kit, Quad Link Assembly - Right 1 1 NLA - Ball Plunger Assembly with Lock Washer 2 1 Locknut (#10-2) 1 2 NLA - Screw, Cap, Socket Head (#10-2 x 1/2") 1 4 NLA - Bushing, Bronze (/16 x 1/4 x 1/4") 1 4 Plate, Stud, Quad Link For 1556 Heavy Duty 1 1 Joystick Screw, Hex Head (1/4-20 x 1-1/2") 1 Spacer (1/4 x /8 x /16") 1 Half Clamp, Non-Threaded Holes 1 1 NLA - Half Clamp, Threaded Holes 1 1 Screw, Phillips Flat Head (#10-2 x 1-1/8") NLA NLA - Kit, Quad Link Assembly - Left 1 1 NLA - Ball Plunger Assembly with Lock Washer 2 1 Locknut (#10-2) 1 2 NLA - Screw, Cap, Socket Head (#10-2 x 1/2") 1 4 NLA - Bushing, Bronze (/16 x 1/4 x 1/4")

98 Item Number Note Part Number Description Quad Link Assembly Before 4/07/06 Quantity Per Package Assembly 8 Plate, Stud, Quad Link For 1556 Heavy Duty 1 1 Joystick 9 Screw, Hex Head (1/4-20 x 1-1/2") 1 10 Spacer (1/4 x /8 x /16") 1 11 Half Clamp, Non-Threaded Holes NLA - Half Clamp, Threaded Holes Screw, Phillips Flat Head (#10-2 x 1-1/8") C NLA NLA - Kit, Quad Link Assembly - Right 1 1 For TCHJOY/TCPDM4 Touchpad 2 NLA - Ball Plunger Assembly with Lock Washer 2 1 Locknut (#10-2) NLA - Screw, Cap, Socket Head (#10-2 x 1/2") NLA - Bushing, Bronze (/16 x 1/4 x 1/4") Screw, Phillips Pan Head (#10-2 x 1-1/8") NLA - Plate, Stud, Quad Link 1 1 MKIV TCHJOY/TCPDM4 9 Screw, Hex Head (1/4-20 x 1-1/2") 1 10 Spacer (1/4 x /8 x /16") 1 11 Half Clamp, Non-Threaded Holes NLA - Half Clamp, Threaded Holes NLA - Screw, Phillips Flat Head Countersunk (# x /8") 1 D NLA NLA - Kit, Quad Link Assembly - Right 1 1 For Van Seats 2 NLA - Ball Plunger Assembly with Lock Washer 2 1 Locknut (#10-2) NLA - Screw, Cap, Socket Head (#10-2 x 1/2") NLA - Bushing, Bronze (/16 x 1/4 x 1/4") Screw, Phillips Pan Head (#10-2 x 1-1/8") Spacer, Joystick Tube, Black NLA - Stud Plate, Quad Link Locknut (1/4-20) 1 16 Screw, Hex Head (1/4-20 x 1-1/2") 1 17 NLA - Spacer (1/4 x 7/16 x 5/8") NLA NLA - Ball Plunger Assembly with Lock Washer 2 1 NOTE: A - Includes the Quad Link, items 2-12 and used with MKIV RII, A, A+,PSF/PSR joysticks B - Includes the Quad Link, items 2-5, 8-1 and used with a 1556 Heavy Duty joystick C - Includes the Quad Link, items 2-6, 8-12, 14 and used with MKIV TCHJOY/TCPDM4 joysticks. Left side mounted Quad Link must be ordered as a special D - Includes the Quad Link, items 2-8, and used with MKIV RII, A, A+, PSF/PSR joysticks attached to a van seat. Left side mounted Quad Link must be ordered as a special E - Quad Link Assembly is no longer available. Please see Quad Link Assembly (After 4/06/06) category and use new Quad LInk design as a replacement. 97

99 Quad Link (QLA - ASBA) and (QL - Captain Seat) After 4/06/06 When converting an old style Quad Link that attaches to a mounting plate or (a Flex or Touch Pad Joystick Tube) is currently on the chair then order the following for: a) ASBA Seat; Quad Link Mtg. Hdwr. (item 4), Quad Link (item 1) & Ht. Adj. Joystick Tube Clamp (item 11) b) Captain Seat; Quad Link Mtg. Hdwr. (item 12), Quad Link (item 1) & Joystick Tube Clamp (item 22) NOTE: Substitute (item 4 & 12) with 2 ea. of the PPH Screws (item 5) when an offset joystick tube is currently on the chair. Additional Joystick Mtg. Hdwr. must be ordered when a 1556 Heavy Duty or TCPD Touch Pad is used. 98

100 Quad Link (QLA - ASBA) and (QL - Captain Seat) After 4/06/06 When converting an old style Quad Link that attaches to a mounting plate or (a Flex or Touch Pad Joystick Tube) is currently on the chair then order the following for: a) ASBA Seat; Quad Link Mtg. Hdwr. (item 4), Quad Link (item 1) & Ht. Adj. Joystick Tube Clamp (item 11) b) Captain Seat; Quad Link Mtg. Hdwr. (item 12), Quad Link (item 1) & Joystick Tube Clamp (item 22) NOTE: Substitute (item 4 & 12) with 2 ea. of the PPH Screws (item 5) when an offset joystick tube is currently on the chair. Additional Joystick Mtg. Hdwr. must be ordered when a 1556 Heavy Duty or TCPD Touch Pad is used. Item Number Note Part Number Description I 1 I 2 A B 4 C,C C1,G,H,H D E F Quantity Per Package Assembly Quad Link w/ Adjustable Joystick Tray (QLA) and Instruction Sheet - Right Quad Link w/ Adjustable Joystick Tray (QLA) and 1 1 Instruction Sheet - Left Quad Link (QL) with Instruction Sheet - Right Quad Link (QL) with Instruction Sheet - Left Kit, Quad Link Latch Hardware Kit, Quad Link Screw Fastener Hardware Kit, ASBA/ADJASBA Quad Link Mounting Hardware 1 1 Screw, Phillips Pan Head w/ Patch (#10-2 x /4") 1 2 Screw, Phillips Pan Head (#10-2 x 1-1/8") 1 2 Tie Wrap (11-1/2" L) 1 1 Spacer, Joystick Tube, Black 1 1 Tube, Joystick Offset (1/2") 1 1 Plug Button, Black (7/8") Screw, Phillips Pan Head w/ Patch (#10-2 x /4") Clamp, Fixed Height Joystick Tube NLA NLA - Kit, Quad Link Mounting Hardware - Van Seat 1 1 Plug Button, Black (7/8") 1 1 Locknut (1/4-20) 1 Tube, Joystick Offset (2") 1 1 Tie Wrap (11-1/2" L) 1 1 NLA - Spacer (1/4 x 7/16 x 5/8") 1 Screw, Hex Head (1/4-20 x 1-1/4") 1 Screw, Phillips Pan Head (#10-2 x 1-1/8") 1 2 Spacer, Joystick Tube, Black 1 1 Screw, Phillips Pan Head w/ Patch (#10-2 x /4") Clamp Assembly, Fixed Height, Captain/ Van Seat NLA Kit, 1556 Heavy Duty Joystick To Quad Link 1 1 Mounting Hardware Screw, Phillips Pan Head (#10-2 x 1/2") 1 2 NLA - Plate, 1556 HD Joystick Quad Link NLA NLA - Kit, TCPD Touch Pad To Quad Link Mounting 1 1 Hardware Plate, TCPD Touch Pad Quad Link 1 1 Screw, Phillips Pan Head (#4-40 x /8") Instruction Sheet, Quad Link

101 Quad Link (QLA - ASBA) and (QL - Captain Seat) After 4/06/06 When converting an old style Quad Link that attaches to a mounting plate or (a Flex or Touch Pad Joystick Tube) is currently on the chair then order the following for: a) ASBA Seat; Quad Link Mtg. Hdwr. (item 4), Quad Link (item 1) & Ht. Adj. Joystick Tube Clamp (item 11) b) Captain Seat; Quad Link Mtg. Hdwr. (item 12), Quad Link (item 1) & Joystick Tube Clamp (item 22) NOTE: Substitute (item 4 & 12) with 2 ea. of the PPH Screws (item 5) when an offset joystick tube is currently on the chair. Additional Joystick Mtg. Hdwr. must be ordered when a 1556 Heavy Duty or TCPD NOTE: Touch Pad is used. A - Latch Kit includes 4 ea. Button Head Cap Screws (10-2 x /8"), 2 ea. Latch Spring Assembly, 4 ea. Phillips Flat C'Sunk Head Screws, 2 ea. Spring Catch Plates, 2 ea. Socket Head Set Screws (10-2 x /8") B - Screw Fastener Kit includes 4 ea. Socket Head Shoulder Screws (/8 x /8"), 2 ea. Socket Head Cap Screws (1/4-20 x /8"), 2 ea. Socket Head Set Screws (1/4-20 x 1/2"), 4 ea. Socket Head Set Screws (10-2 x 1/8") C - Includes items The Quad Link Mounting Hardware accommodates MKIV RX, A, A+ and PSF/PSR joysticks. C1 - When ordering the Quad Link for the first time, Additional hardware is required for 1556 Heavy Duty and TCPD Touch Pad joysticks. See pictorial for reference. D - Includes items 24 and 25 E - Includes items 27 and 28 F - Not Shown G - Includes items The Quad Link Mounting Hardware accommodates MKIV RX, A, A+ and PSF/PSR joysticks. H - If Quad Link is to be mounted on chairs w/ van seats built Before 4/07/06, then the Armrest Attach. Hdwr. ( ) for 18" wide or ( ) for 20" & 22" wide must be ordered as well. H1 - See page titled "Captain Seat Arms and Hardware" page. The new armrest plates have additional holes drilled so that the quad link can be properly mounted. I - Use with Captain Seats only 100

102 MKIV Controllers, Programmer and Hardware MKIV Quad Pulse and MKIV RII 80 AMP 101

103 MKIV Controllers, Programmer and Hardware MKIV Quad Pulse and MKIV RII 80 AMP Item Number Note Part Number Description Quantity Per Package Assembly 1 E NLA NLA - Controller, MKIV Quad Pulse NLA NLA - Controller, MKIV RII (80 AMP) Washer, Flat (21/64 x 5/64 x 7/64") Locknut (5/16-18) F Switch, Red Flex Ribbon (Tape) Reset G Kit, Switch, Black Egg Reset w/ Hook/Loop 1 1 Adhesive Back Fastener & Attaching Screws (EGSBLK) NLA NLA - Programmer, Remote 1 1 A,B NLA NLA - Virtual Service Modem Kit 1 1 A,C NLA NLA - Virtual Service Software Kit 1 1 A,B NLA NLA - MKIV One 2 One Software Kit 1 1 A,D NLA NLA - Printer and Interface 1 1 A Cable, Virtual Service, Charger/Modem 1 1 A NLA NLA - Disk,.5 H.D. Floppy with V.S. Software 1 1 A NLA NLA - Adaptor, Null Modem 1 1 A NLA NLA - Service Manual - V.S. Software Kit 1 1 A NLA NLA - Paper, Printer 1 1 A NLA NLA - Harness, Printer Wiring 1 1 NOTE: A - Not Shown B - Part number is available for individual sale C - Part number , , and are available for individual sale D - Part numbers and are available for individual sale E - When a Customer upgrades from a MKIV RII to a MKIV Quad Pulse controller, a new wire harness is required. See Battery and Charger page. F - Before 5/24/04 G - Not Shown. After 5/2/04 the Egg Reset Switch replaced the Red Flex Ribbon (Tape) Reset Switch 102

104 MKIV Sip-N-Puff/Digital Interface and COM12 and COM4 10

105 MKIV Sip-N-Puff/Digital Interface and COM12 and COM4 Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Sip-N-Puff w/ Digital Interface D See Note-NLA See Footnote NLA NLA - Module, Communication, COM4/AUX A NLA NLA - Kit, COM12/AUX12 and COM4/AUX4 1 1 Mounting Hardware 1 Half Clamp, Threaded Holes Half Clamp, Non-Threaded Holes 1 1 NLA - Screw, Hex Head (1/4-20 x 1-1/8") NLA - Fastener, Dual Lock Hook and Loop 1 1 Adhesive (2" W x 12" L) 5 NLA - Plate, COM12/AUX12 and COM4/AUX4 1 1 Mounting 11 B,C Kit, SNP/DI, MK5 SAC, 4WSB, S4WSB, GTAM, 1 1 AUX12M6, AUX4M6 Mtg. Hdwr. 1 Half Clamp, Threaded Holes Half Clamp, Non-Threaded Holes 1 1 NLA - Screw, Hex Head (1/4-20 x 1-1/8") Screw, Phillips Pan Head (#4-40 x /8") Plate, Mounting 1 1 NOTE: A - Mounting hardware includes items 1-5. Item 4 that is packaged with the kit will only be a 4" long "loop" fastener B - Includes items 1- and 6-7 C - As of 5/22/07 the Mounting Plate holes and the orientation of the Hardware was revised to attach the electronics closer to the chair. The Mounting Hardware Kit is backward compatible. D - Part is no longer serviceable in the field. 104

106 MKIV Displays 105

107 Item Number Note Part Number Description MKIV Displays Quantity Per Package Assembly NLA NLA - Display without Switches Display with Switches 1 1 A NLA NLA - Tube, Flex with Screws Screw, Phillips Pan Head (#4-40 x /8") Clamp, Fixed Height Joystick Tube B Switch, Red Flex Ribbon (Tape) Reset C Kit, Switch, Black Egg Reset w/ Hook/Loop 1 1 Adhesive Back Fastener & Attaching Screws (EGSBLK) 8 D Clamp, Height Adjustable Joystick Tube (ARM250) 1 1 NOTE: A - Includes item 4 B - Before 5/24/04 C - After 5/2/04 the Egg Reset Switch replaced the Red Flex Ribbon (Tape) Reset Switch D - Can be used to replace a Fixed Height Joystick Tube Clamp in the field 106

108 MKIV R.I.M. Head Control Mounting Hardware 1500M4 Item Number Note Part Number Description Quantity Per Package Assembly Cover, Nylon NLA NLA - Cover, Nylon NLA NLA - Clamp with Knob, Two-Piece Screw, Socket Button Head (#10-2 x /4") NLA NLA - Package, Screw, Hex Head (1/4-20 x /4") NLA NLA - Bracket, Attaching, Black (12-18" W) NLA NLA - Bracket, Attaching, Black (19-24" W) Screws with Washers (#10-16 x 7/8") Screw w/ Washer (#10 x 7/8") NLA NLA - Bracket, Wing, Black Washer (1/4 x 1/2 x 1/16") Locknut (1/4-20) Washer, Nylon (/16 x 7/16 x 1/8") NLA NLA - Locknut, High Profile (#10-2) A Hardware, Rim Control Mounting (RIMHW) (12-18" 1 1 W) 12 A Hardware, Rim Control Mounting (RIMHW) (19-24" W) 1 1 NOTE: A - Includes Items

109 MKIV R.I.M. Head Control Assembly 1500M4 108

110 MKIV R.I.M. Head Control Assembly 1500M4 Item Number Note Part Number Description A B C 8 D E Quantity Per Package Assembly Tie Rod End X000 Locknut (#10-2) NLA NLA - Screw, Set w/ Patch (#8-2 x 1/4") O-Ring (1/2" I.D.) Screw, Phillips Pan Head (#8-2 x /8") NLA NLA - Washer, Nylon Block, Pivot NLA NLA - Ring, Snap Bearing, Linear NLA NLA - Shield, Push Rod Screw, Phillips Pan Head (#4-40 x 1/2") NLA NLA - Bracket, Headrest Mounting, Black X002-NLA NLA - Screw, Phillips Oval Head (#10-2 x /4") NLA NLA - Spring, Compression (19/2 x 1-1/4 x 1/2") NLA NLA - Rod, Push NLA NLA - Screw, Phillips Pan Head (#6-2 x 1/4") Washer, Nylon (1/4 x 1/2 x 1/16") NLA NLA - Collar, Shoulder X64-NLA NLA - Boot, Joystick NLA NLA - Rod, Pivot X014 Screw, Phillips Round Head (#10-2 x 1") NLA NLA - Tie Wrap (4-1/4" L) NLA NLA - Cover, Splash Washer, Plain (1/2 x 1 x 1/8") NLA NLA - Ribbon Reset Switch and Bracket Assembly E-NLA NLA - Reconditioned - Joystick, Remote Head NLA NLA - Clamp, Horizontal Pivot NLA NLA - Clamp, Threaded, Horizontal Pivot NLA NLA - Screw, Socket Head (M6 x 1 x 25mm) Tube, Slide, Square, Short NLA NLA - Clamp, Vertical Pivot NLA NLA - Clamp, Threaded, Vertical Pivot NLA NLA - Tube, Slide, Square, Long Hardware, Adjustment Screw, Socket Button Head (#10-2 x 1") NLA NLA - Washer, Lock Tooth (/16 x /8 x 1/2") Kit, Headrest with Hardware, Otto Bock, Small Kit, Headrest with Hardware, Large NLA NLA - Screw, Socket Head (#10-2 x 1/2")

111 NOTE: MKIV R.I.M. Head Control Assembly 1500M4 A - Includes items B - Includes items 27- and the Plug Buttons that attach to item 0 and Slide Tubes. The Plug Buttons are not saleable. C - Includes the Headrest Adapter and items 5 and 6. D - Includes the Headrest Adapter and items 5 and 6. The LaBac Headrest is no longer used as of 12/6/10 that was attached with Screw part # (4 ea.). The screw is still available to order for existing LaBac Headrest in the field. E - Used for existing LaBac Headrest in the field only. 110

112 MKIV Joystick Options 111

113 Item Number Note Part Number Description 1 M A B C D E N F 4 5 G 6 H 7 I 8 L J K MKIV Joystick Options Quantity Per Package Assembly See Note See Footnote NLA NLA - Clamp, Universal Swivel X000 Handle, Lock, Chrome X000 Locknut (1/4-20) NLA NLA - Joystick Tube with Plug Button Assembly Plug Button, Black (7/8") Joystick, Attendant Control (1552M) NLA NLA - Joystick, Heavy Duty NLA NLA - Kit, Straight Joystick Tube with Hardware NLA NLA - Screw, Phillips Round Head (#10-2 x /8") Plug Button, Black (7/8") Hardware, Rear Cane Mount (167/RCM) Plug Button, Black (7/8") Adjustment Lock Assemnbly, Black NLA NLA - Bracket, Upright, Black -Right NLA NLA - Tube, Joystick Screw w/ Washer (#10 x 7/8") Tube, Arm Mount with Plug Button, Black Plug Button, Black (7/8") NLA NLA - Joystick, MKIV Dual/Compact Hardware, Dual/Compact Joystick Clamp Mounting Clamp Screw, Socket Button Head (#10-2 x 5/16") NLA NLA - Clamp, Mounting NLA NLA - Screw, Socket Head (#10-24 x 1/2") NLA NLA - Spacer, Split (/8" I.D.) NLA NLA - Chin Cup Assembly Cup, Chin NLA NLA - Screw, Adaptor X000 Screw, Set Socket Cup Point (#8-2 x 1/4") NLA NLA - Touchpad, Joystick Assembly NLA NLA - Kit, Straight Joystick Tube with Hardware Plug Button, Black (7/8") Screw, Phillips Pan Head (#4-40 x /8") Clamp, Fixed Height Joystick Tube Switch, Red Flex Ribbon (Tape) Reset Kit, Switch, Black Egg Reset w/ Hook/Loop 1 1 Adhesive Back Fastener & Attaching Screws (EGSBLK) Clamp, Height Adjustable Joystick Tube (ARM250) Display with Switches NLA NLA - Display without Switches

114 NOTE: MKIV Joystick Options A - Includes the joystick tube and items 10 and 11 B - Includes items 1-17 C - For On-Chair model numbers 1678 and Includes the joystick tube and item 19 D - Includes items E - Includes items 28-0 F - Includes the joystick tube, items and 4 G - Individual components are non-saleable. H - Before 5/24/04 I - After 5/2/04. The Egg Reset Switch replaced the Red Flex Ribbon (Tape) Reset Switch J - Not Shown and used with the Heavy Duty and Touch Pad Joystick K - Not Shown and used with the Remote Joystick L - Can be used to replace a Fixed Height Joystick Tube Clamp in the field M - No longer available as a service part in the field. N - Part # is no longer available as a service part individually. Order item #27 as a replacement. 11

115 Tash and Therafin Accessories NOTE: For more information on Tash and Therafin products, please contact one of our Rehab Specialists. 114

116 Tash and Therafin Accessories NOTE: For more information on Tash and Therafin products, please contact one of our Rehab Specialists. Item Number Note Part Number Description Quantity Per Package Assembly 1 P5820-NLA NLA - Switch, Red Soft P5821 NLA - Switch, Green Soft C P5018-NLA NLA - Wafer Board (5018) 1 1 C P5026-NLA NLA - Star Control C P5020 Mini Joystick with Push (5020) P47-NLA NLA - Multi-Ability Cable P45-NLA NLA - CA5 Multi-Connector Box P5970-NLA NLA - Clamp, "U" 1 1 B Bib Assembly (PKG2669) 1 1 B P21456-NLA NLA - Adaptor Clamp - Tash 1 1 B P21457-NLA NLA - Adaptor Clamp - Invacare 1 1 B P21460-NLA NLA - Midline Swingway System 1 1 A,B Kit, Sip-N-Puff, 16" Fixed (PKG2666) 1 1 Includes: () Air Tube Straws, (2) Saliva Traps, Tubing, Pivot Shaft/Flexible Metal Gooseneck Assembly, and Extruded Figure "8" Clamp to fit 7/8" Wheelchair Frame Tubing. Extruded Back Cane Adapter Clamp. B Display with Switches 1 1 NOTE: A - See items included. B - Not Shown C - Must be used with display with switches part #

117 Power Wheelchair Tool Kit 116

118 Item Number Note Part Number Description NLA Power Wheelchair Tool Kit NLA - Kit, Power Wheelchair Tool Includes: 1 ea. Multimeter with Leads 1 ea. Locator, Protractor/Angle Magnetic Base 1 ea. Instructions, MKIV Programmer 1 ea. Wire, Grounding with Hand Strap and Clip 1 ea. Leads, 1" Test 1 ea. Light, Pen with Invacare Logo 1 ea. Tape Measure, Compact with Invacare Logo 1 ea. Screwdriver, Pen-Size Phillips/Flat Head 1 ea. Cable, Virtual Service Charger/Modem Quantity Per Package Assembly

119 Item Number Note Part Number Description NOTE: Miscellaneous Accessories Quantity Per Package Assembly A,C Strap, Positioning, Seat/Chest w/ Auto Style Buckle 1 1 (Eyelet to Eyelet Length ") C Strap, Positioning, Seat/Chest w/ Auto Style Push 1 1 Button Buckle (Eyelet to Eyelet Length 48") B,C Strap, Positioning, Seat/Chest w/ Auto Style Push 1 1 Button Buckle (Eyelet to Eyelet Length 61") C Strap, Positioning, Seat/Chest w/ Airline Style 1 1 Buckle (Eyelet to Eyelet Length 46") C Strap, Positioning, Seat/Chest w/ Airline Style 1 1 Buckle (Eyelet to Eyelet Length 61") C Strap, Positioning, Seat/Chest w/ Hook and Loop 1 1 Style Buckle (Eyelet to Eyelet Length 61") C 40176X010 Pump, Tire 1 1 A " positioning straps come rainbow color. B - 20" wide seat positioning straps are used with 18" wide captain seats and 2" wide seat positioning straps are used with a 22" wide captain seat. C - Not Shown. 118

120 Part Number Description QTY per Assembly WARR RPLMT - Charger, Battery, E-NLA Amp. 115vac (Off Board) Single Mode Round Plug w/ AC 1 See Note(s) A Power Line Cord, CTE Corp. NOTE: A - See "Charger - Battery & Harness" Category for more information. 119

121 Invacare Corporation One Invacare Way Elyria, Oh USA Technical Support Florida Technical Support Customer Service Invacare Corporation. All rights reserved. Republication, duplication or modification in whole or in part is prohibited without prior written permission from Invacare. Trademarks are identified by and. All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted. (Revised /26/18)