XCEL80 Steering Control Units

Transcription

1 XCEL80 Steering Control Units

2 XCEL80 Steering Unit SEPECIFICATION DATA Max. System Pressure 175 bar [2537 psi] Max. Back Pressure 21 bar [305 psi] Rated Flow 75 LPM [20 GPM] Input Torque Powered Nm Max. System Operating Temperature 93 C [200 F] Max. Differential Between 28 C [50 F] Steering Unit and Other System Temperature Fluid ATF Type A and Most Petroleum Based Fluids See Eaton Technical Bulletin Recommended Filtration ISO 24/18/13 cleanliness level Applications Wheel loader Wheel excavator Backhoe loader Dump Truck Grader Features Q-Amp steering units, provide amplified displacement to meet the steering wheel s high turning speed requirements. Load sense dynamic and load sense static available. 2:1 and 1.6:1 Q-Amp ration options and customized design is available. Effective Displacement (Displacement X Q-Amp ratio) options: 500cc/r, 630cc/r, 800cc/r, 1000cc/r. Available package supply with Eaton VLE and VLH priority valve, applicable in many vehicles steering system. Benefits Integral body design, with anti-cavitation valves and cylinder relief valves integrated, reduced risk of leakage. Optimized flow path design reduced pressure drop and power consumption. Cylinder damping feature reduced vehicle jerk and improved system stability. Optimized spool and sleeve reduced inertia shock and improved steering stability and reliability. Optimized Q-Amp feature, quicker response and better control on turning speed. Hydraulic Circuits Dynamic Signal Static Signal 2 EATON XCEL80 Steering Control Units E-STCU-CC001-E December 2013

3 XCEL80 Steering Unit Dimensions Port M20X1.5 M20X1.5 O-ring Load Sense Port M12X1.5 M12X1.5 O-ring Mechanical Interface Internal Involute Spline, 12 tooth 16/32 DP30 PA Q-Amp Ratio 2:1 Q-Amp Ratio 1.6 :1 Effective Effective Displacement, cc/r Displacement, cc/r Displacement cc/r Dimension L1, mm Dimension L2, mm EATON XCEL80 Steering Control Units E-STCU-CC001-E December

4 Q-Amp Flow Amplification for Load Sensing Circuits Description and Advantage Q-Amp steering units have built in variable orifices that provide flow directly to the cylinder without going through the gerotor section. The orifices do not open until after the gerotor begins to rotate and then gradually open until the desired flow is achieved which is proportional to the flow going through the gerotor. A typical Q-Amp unit has a ratio of 1.6:1 which means the flow of the cylinder is 1.6 times the flow going through the gerotor when turning the steering wheel at medium to fast speeds. (See model code for available ratios.) Conventional Steering Control Unit Fast Turn Pump Rotary Valve Q-Amp Steering Control Unit Fast Turn Meter Cylinder Fast Turn Rotary Valve Meter Features Variable Ratio 2:1 Pump Cylinder 1.6:1 Ratio 1:1 Turns Lock to Lock RPM Q-Amp Steering Control Unit Slow Turn Slow Turn Pump Rotary Valve No Flow Meter Cylinder RPM 4 EATON XCEL80 Steering Control Units E-STCU-CC001-E December 2013

5 Model Code Customer Order Information The following 31-digit coding system has been developed to identify all of the configuration options for the XCEL80 steering control units. Use this model code to specify a unit with the desired features. All 31-digit of the code must be present when ordering. You may want to be photocopy the matrix below to ensure that each number is entered in the correct box. This model code shows Preferred Products only. For a complete model code listing all available options, please contact your Eaton representative. ASJ A 5 2 A * * * * E * * * * * * * * * A * A 4 A AA * * A , 2 3, Product Series ASJ Series XCEL80 Steering Control Unit 4 Unit Type A Standard 5 Nominal Flow Rating 5 75 L / min 20 GPM Q-Amp 6 Inlet Pressure Rating bar 7 Return Pressure Rating A 21 bar [ 300 psi] Maximum 8, 9 Displacement cm 3 /r [15.2 in 3 /r] cm 3 /r [19.5 in 3 /r] cm 3 /r [24.4 in 3 /r] cm 3 /r [30.5 in 3 /r] 10 Flow Amplification B 1.60:1.00 C 2.00: Neutral Circuit B Load Sensing, Static Signal C Load Sensing, Dynamic Signal 12 Load Circuit E Non Reaction,Cylinder Damped, Level , Valve Option 00 None 17 Cylinder Relief Valve, Anti-Cavitation Valve 18 Cylinder Relief Valve, Anti-Cavitation Valve, Inlet Check Valve 19 Cylinder Relief Valve, Anti-Cavitation Valve, Load Sense Relief Valve Cylinder Relief Valve, Anti-Cavitation Valve, Load Sense Relief Valve, Inlet Check Valve 15 16, Load Sense Relief Valve Setting 00 None bar [1885 psi] bar [2030 psi] bar [2175 psi] bar [2247 psi] bar [2320 psi] bar [2392 psi] bar [2537 psi] bar [2465 psi] 17 18, Cylinder Relief Valve Setting 00 None bar [2755 psi] bar [2900 psi] bar [3045 psi] bar [3190 psi] bar [3262 psi] bar [3335 psi] bar [3407 psi] * Cylinder Relief Valve settings is required to be a minimum of 60 bar higher than the Load Sense Relief Valve Setting P, T, L, and R Port Size C 4X M20 x 1.5-6H Metric Port D 4X M20 x 1.5-6H Metric O-ring Port E 4X G.500 BSP Straight THD Port J 4X UNF-2B SAE O-ring Port 20 21, Additional Ports AA None AB M12 x 1.5-6H Load Sensing Metric Port AC M12 x 1.5-6H Load Sensing Metric O-ring Port AD G BSP Straight Thd Load Sensing Port AF UNF-2B Load Sensing SAE O-ring Port 22 Mounting Threads A 4-M10X1.5 Mounting Threads Mounting Face 23 Mounting Threads Port Face A None B 2-M12X Mechanical Interface A Internal Involute Spline, 12 tooth 16/32 DP 30 Degree PA 25 Input Torque 4 Neutral Low 26 Fluid Type A Reference Eaton Technical Bulletin , Special Features AA None 29 Paints & Packaging 1 Black Paint 2 Blue Paint 30 Identification 0 Bar Code, Eaton Product Number on Nameplate 1 Bar Code, Customer Number on Nameplate 31 Design Code A A NOTE: A dynamic signal steering unit must be used together with a dynamic signal priority valve. Please always show your selected product number when you place an order. Customer Order Information Part Number Model Code ASJA52A11CBE170030DACABA4AAA11A EATON XCEL80 Steering Control Units E-STCU-CC001-E December

6 Eaton Hydraulics Group USA Lone Oak Road Eden Prairie, MN USA Tel: Fax: Eaton Hydraulics Group Europe Route de la Longeraie Morges Switzerland Tel: +41 (0) Fax: +41 (0) Eaton Hydraulics Group Asia Pacific Eaton Building 4th Floor, No.7 Lane 280 Linhong Rd. Changning District Shanghai China Tel: (+86 21) Fax: (+86 21) Eaton Corporation All Rights Reserved Document No. E-STCU-CC001-E December 2013