B o d y S t r u c t u r e

Size: px
Start display at page:

Download "B o d y S t r u c t u r e"

Transcription

1 B o d y S t r u c t u r e Body Glass Glass replacement should meet standards in specification FMVSS 205 and 217. [Warning] When replacing broken or damaged glass, use extreme care at all times to prevent personal injury. Use proper replacement parts, tools and personal protective equip-ment, such as gloves and safety goggles. Windshield Glass Replacement Remove vertical filler strip in glazing rubber on each side of broken glass. Remove horizontal filler strip in glazing rubber on top and bottom of broken glass. It will be necessary to cut the horizontal filler strip after it is pulled past the glass. 1. Starting at a corner, push glass free of glazing rubber from inside of bus outward and remove. 2. Position new glass in glazing rubber. 3. Using installation tool, work glass into glazing rubber. Using glazing tool to help work gasket around windshield 4. Seal glass to glazing rubber from outside of the bus with an adhesive sealant, such as Silastic 732 RTV Adhesive/ Sealant. 5. Apply soapy solution to filler strip channel on glazing rubber to act as a lubricant for easier installation of filler strip. 6. Using filler strip tool, insert fillet strip into channel on glazing rubber. Applying the filler strip 909 Window gasket tool Filler strip insertion tool

2 1 s e r v i c e m a n u a l Rear Vision Glass Replacement 1. Remove filler strip from channel in glazing rubber. 2. Apply pressure against glass from the outside of the bus starting at a corner, push glass and glazing rubber off metal flange. 3. Remove glazing rubber from glass. 4. Put glazing rubber on new glass. 5. Apply a soapy solution to the flange on the bus body and to the filler strip channel on glazing rubber. This acts as a lubricant for easier installation. Using a cord to help install gasket around glass 6. Wrap a cord around the glazing rubber and rest the glass on the bottom window flange from the inside of the bus body. See Figure Apply pressure from the inside of the bus body to ensure glass is seated properly. Pull cord slowly and work glazing rubber onto the window flange. 8. Using a filler strip tool, insert the filler strip into the channel on the glazing rubber. The filler strip tool is available from your distributor. See Figure Apply clear caulking around glass and window flange on the outside of bus body to ensure that no leaks occur. Applying Filler Strip 910

3 1 s e r v i c e m a n u a l Transit Sliding Window Removal 1. Remove screws in outside aluminum extrusion. 2. oosen sealer between window frame with putty knife. [Caution] Do not pry window frame from body without loosening sealer. Unless sealer is loosened, window frame will be bent. 3. Pry out using screwdriver. 4. Reverse procedure for installation. Transit Window Glass Replacement On push out windows, when hinge screws are removed and interior latch released, window sash may be removed from frame. 1. Release window lever (1) located inside the bus at the bottom of each pushout window. 2. Remove hinge screws (2) on outside of body. 3. ift and pull window out of section. 4. To remove stationary transit sliding window, remove all screws between inner frame (4) and outer frame (5). 5. ift and pull window out of section. 6. Remove four screws and take out vertical brace (6) located in the center of the window Remove two window stops (one on each side of the top of window). 8. Slide glass to the center of the window. Spread apart the inner frame (4) just enough to lift glass frame (7) out. 9. To remove glass from frame, slide rubber seal (8) out of vertical rail (9) exposing two screws. Window glass is removable after screws are removed. Remove glass. 10. To replace glass, slip glazing vinyl seal around glass and slide into frame. 11. Reassemble by reversing procedure.

4 b o d y s t r u c t u r e Transit Sliding Window Pushout Transit Sliding Window 913

5 1 s e r v i c e m a n u a l Outward Opening Entrance Door The outward opening door panels are hung in a prefabricated framework before mounting into the body construction. The doors are suspended from sealed ball bearings located at the upper corners of the door. These components are accessible only from inside the body. The bronze bearings at the lower corners of the door assembly are not weight bearing, but serve to hold the bottom of the assembly in position. These bronze bearing are permanently lubricated and should require little maintenance during the service life of the door assembly, which exceeds 300,000 cycles. The interlink between the door panels is installed as a single assembly in the door header, and is adjustable for maintaining proper opening/closing tension. Interlink Adjusment The mechanical link between the doors (the interlink rod) should be adjusted so that the rearward door closes and seats first. One of the spherical bearing, rod end connectors has a right-hand thread; the other has a left-hand thread. This allows for length adjustment by simply turning the interlink rod. The forward door panel then closes with an overlap to the rear of the bus, helping to reduce the intrusion of outside air while the bus is in motion. The forward door pivots across the centerline of a cam, thus locking the rear door panel in position. When properly adjusted, the door should begin to require more energy to close as the trailing edge of the front door panel gets to within 2 or 3 inches of the closed position. When the mechanism is properly adjusted, you should only be able to push the door open by pressing on the forward door panel from the inside. The rearward panel should be locked into position and will not move until the forward panel moves. 1. With the doors open, loosen the jam nut at the forward end of the interlink rod. The jam nut on the rearward end of the interlink assembly is to hold the bumper in position and is located inside the access panel over the door Turn the interlink tube until, by trial and error, the door mechanism operates properly. 3. Tighten the jam nut securely.

6 b o d y s t r u c t u r e Interlink Adjustment 915 ower Pivots Outward Opening Door

7 1 s e r v i c e m a n u a l Manual Door Control Manual Door Control Arm Removal The manual door control rod does not need to be removed to adjust or remove the door panel assemblies. However, the clevis pin must be removed when removing the door panels. Control Arm/ Handle Pivot Bolt 1. Remove the cotter pin and clevis pin securing the control arm to the door. 2. If the control arm is in the way of your work, remove it by removing the pivot bolt, nut, and spacer from the handle. Control Arm/ Handle Pivot Bolt Spacer Control Arm Manual Door Control Reinstallation If the length of the manual control rod assembly is moved, the nominal length for outward opening doors should be set to inches ( cm). Then adjust to close with proper tension. When the door operates satisfactorily, tighten all hardware securely. 1. If necessary, install the door/control arm pivot. Snug up so it will not move. Do not tighten securely at this time. Remove this nut to detach handle end of Control Arm Door Pivot Clevis Pin Door/Control Arm Pivot 2. With the doors in the closed position, pre-assemble the control arm to the approximate length required Attach the clevis to the door pivot and insert the clevis pin. Do not install the cotter pin at this time. 4. Assemble the opposite end of the control arm to the handle and tighten the locknut securely. 7. By trial and error, adjust the length of the rod assembly by removing the clevis pin and turning the clevis. Adjust the rod assembly length so that the control assembly handle passes through the center of the control assembly s cam action as the doors reach the fully open position. 8. When the door opening mechanism operates properly, tighten all hardware securely. Install the cotter pin into the clevis pin. Tighten the jam nut at the clevis in the rod assembly.

8 b o d y s t r u c t u r e Pneumatic Door Opener The pneumatically operated outward opening door operates similarly to the manual door described above but uses an air cylinder mechanism located inside the door header to actuate the door. Pneumatic Door Opener Removal 1. Remove the cotter pins and clevis pins from each end of the actuator. 2. Disconnect the electrical connectors. 3. Remove the pneumatic tubing. Identify the tubing as you remove it and replace it in the same positions. 4. Carefully remove the actuator from the compartment. Pneumatic Door Opener Reinstallation Installation of the pneumatic door actuator is accomplished in the reverse order of the removal instructions, above. An air flow control valve located at each end of the actuator assembly allows adjustment of the speed of the door operation. Properly operating doors should cycle open or close in 3 seconds. If the doors do not operate properly, refer to Adjustment of Outward Opening Door Mechanism, above. 917

9 1 s e r v i c e m a n u a l Electric Door Opener Electric Door Opener Removal 1. Remove hardware holding access panel over the door assembly. 2. Remove the nut and capscrew assembly from 10 places. 3. Disconnect electrical connectors at the relay assembly. 4. Remove the clevis pin from forward door lever. 5. Remove the clevis pin from rearward door lever. Relay Assembly 6. Remove the actuator assembly. Electric Door Opener Reinstallation Install the electrically operated door actuator in the reverse order of the removal instructions above. 1. Pre-install the relay assembly on the actuator housing. 2. Preset the length of the actuator rod assembly to inches (46.99 cm). Be sure the clevis pinholes are properly oriented. 3. Install the actuator assembly by installing bolt and locknut in 10 places. Tighten securely. 4. Install the actuator rod assembly clevis to the lever on the electrically operated actuator Install the actuator rod clevis to the forward door operating lever. 6. Check for proper operation of the actuator. It may be necessary to adjust the length of the actuator rod assembly so the door will stop before the motor crosses center. 7. If necessary, install the emergency release lever. 8. Move the open position stop to its rearmost position to prevent the motor driven actuator from rotating too far rearward. 9. After adjusting for proper operation, position cam on the rotating shaft to operate limit switch when the door is in the open position.

10 b o d y s t r u c t u r e Door Panels Door Panels Removal If so equipped, optional safety equipment attached to the door panel s assembly must be disconnected and/or removed before continuing. Access to the door mechanism is provided over the door opening, inside the bus. 1. Remove the access panel cover or header. 2. If equipped with pneumatic door actuator, refer to Removal of Optional Pneumatic Door Opener above. 3. If equipped with electrically operated door actuator, disconnect the actuator rod clevis from the front door operating lever. 4. Remove Allen head machine screws and lock nuts from spherical bearing (at each end of the connector link). 5. Remove the connecting link. 6. Remove the nut, lock washer and flat washer from the bearing at the top outside corners of the door panels. 7. Support the door panels and remove two carriage bolts from the lower outside corner of each door panel. 8. ift the door panel and slide the bottom, with bracket and bronze bushing attached, away from the stepwell. Some manipulation of the rearward door panel may be necessary to remove the door lever from the header. 9. ower the door panel until it clears the header. 10. Set the door panel aside and remove the forward door panel in the same manner Remove the sealed ball bearings from the outside corners of the door header. 12. Remove the flanged bronze bearing and bracket from the bottom of each door panel. Door Panels Reinstallation Installation of the outward opening door panels is accomplished, in the reverse order of the removal instructions above.

11 1 s e r v i c e m a n u a l 1. Install the sealed ball bearings at two places in the header, at the outside corners. 2. Install the bronze bearings and brackets at the bottom outside corner of each door panel. 3. Install the rearmost door panel first. Some manipulation may be necessary to install the rear door panel control lever into the header. 4. Support the door panel and install the lower door pivot bracket and bronze bearing. 5. Install two carriage bolts to secure the pivot assembly in the stepwell. 6. Install the upper spacer. 7. Install the upper pivot through the upper support bearing. Install flat washer. Wipe pivot threads clean and coat the bottom 3 to 5 threads with octite. Install lock washer and nut to hang door panel in frame. Torque to 30 ft-lbs (3.38 Nm). 8. Install forward door panel bronze bearing and bottom pivot bracket onto the door panel. 13. Install the upper pivot through the sealed ball bearing. 14. ift and support the door panel while installing two carriage bolts to secure the bottom pivot to the stepwell. Install the flat washer. Wipe top pivot threads clean and apply octite to the bottom 3 to 5 threads. Install lock washer and nut. Torque to 30 ft-lbs (3.38 Nm). 920

12 b o d y s t r u c t u r e Door Panel Glass Replacemement With the old glass and the rubber gasket removed, clean the inside edges of the door panel opening. Using a new rubber gasket of the proper size: 1. Install a new rubber gasket onto the new glass. 2. Place a sash cord, or other suitable string, around the outside groove of the glass assembly. 3. Pull the string tight to make sure it seats fully into the groove. eave the ends of the sash cord hanging down from bottom corners of new glass assembly. Do not lubricate the new gasket material. 4. Install the glass assembly into the door panel, from the inside, placing the bottom groove of the rubber gasket properly straddling the bottom of the opening in the door panel. Be sure the ends of the sash cord are on the outside of the door panel, protruding from the lower corners of the opening. 5. From the inside of the door assembly, press and hold the glass assembly securely into the hole. 6. From the outside of the door assembly, carefully pull the sash cord, causing the outer edge of the gasket to pop into place. 921

B o d y S t r u c t u r e

B o d y S t r u c t u r e B o d y S t r u c t u r e Body Glass Glass replacement should meet standards in specification FMVSS 205 and 217. [Warning] When replacing broken or damaged glass, use extreme care at all times to prevent

More information

Doors. Table of Contents

Doors. Table of Contents Doors Table of Contents Sub-Headings Safety 2 Warnings 2 Cautions 2 s 2 Introduction 2 Description of Operation 2 Door Control Assembly Removal 2 Remove Cotter Pin and Clevis Pin From Rod-End Bracket 3

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave

More information

Installation Guide Current Ford F-250 & Ford F-350 Super Duty. Product Code: 109 & 119

Installation Guide Current Ford F-250 & Ford F-350 Super Duty. Product Code: 109 & 119 Installation Guide 2008 - Current Ford F-250 & Ford F-350 Super Duty Product Code: 109 & 119 September 1, 2012 Tools Needed Components Included 3/8" Drill P2 Tip #2 Philips Screwdriver 1/2" Drill Bit Hinged

More information

Page 1 of 15 Transmission, Model S5-42 ZF Model S5-42 ZF Disassembly NOTE: For 4x4 and F-Super Duty vehicles, skip to Step 5. 1. Attach the transmission to the Bench Mounted Holding Fixture T57L-500-B

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD SILVERADO 1500 PART #

INSTALLATION INSTRUCTIONS GRILLE GUARD SILVERADO 1500 PART # INSTALLATION INSTRUCTIONS PART # 3-5863 4-0863 PARTS LIST: Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD GMC SIERRA 1500 EXCLUDES DENALI PART # 4084/

INSTALLATION INSTRUCTIONS GRILLE GUARD GMC SIERRA 1500 EXCLUDES DENALI PART # 4084/ INSTALLATION INSTRUCTIONS GRILLE GUARD 14-15 GMC SIERRA 1500 PART # 4084/ 4084-2 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4

More information

CBT25, 50 & 100 driveshaft

CBT25, 50 & 100 driveshaft CBT25, 50 & 100 driveshaft replacement 2 CBT driveshaft REPLACEMENT Revision History rev. level 01_03.13.2014 NOTE: due to the fact that a new machine (never exposed to seed treatment) was used to demonstrate

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL MODEL SR PASSENGER AND CREW DOORS. DESCRIPTION AND OPERATION Serials 000 thru 00: The two crew/passenger doors incorporate a flush-mount outside door handle, key-operated door lock, and a conventional

More information

Installation Notes: #86000-R Race Series +3.5 L/T Kit

Installation Notes: #86000-R Race Series +3.5 L/T Kit 159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation

More information

Volkswagen New Beetle Body - Exterior 64 Glass, Window regulators (Page GR-64)

Volkswagen New Beetle Body - Exterior 64 Glass, Window regulators (Page GR-64) 64 Glass, Window regulators (Page GR-64) Flush bonded windows Body flange, preparing for glass installation Broken rear window, removing Cleaning off excess adhesive material Curing time Installation instructions

More information

Installation Instructions JASMINE Spread Lavatory Faucet with the EverClean Finish & Speed Connect Drain

Installation Instructions JASMINE Spread Lavatory Faucet with the EverClean Finish & Speed Connect Drain Installation Instructions JASMINE 80. Spread Lavatory Faucet with the EverClean Finish & Speed Connect Drain Congratulations on purchasing your American Standard faucet with the EverClean finish and Speed

More information

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045

More information

(W) INSTALLATION INSTRUCTIONS GRILLE GUARD 2014 GMC SIERRA 1500 EXCLUDES DENALI PART # /

(W) INSTALLATION INSTRUCTIONS GRILLE GUARD 2014 GMC SIERRA 1500 EXCLUDES DENALI PART # / (W) INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 508514/ 508515 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE

More information

SAF-T-LINER MVP-ER PARTS MANUAL. Doors Section. Page 4-1. Doors 10/96

SAF-T-LINER MVP-ER PARTS MANUAL. Doors Section. Page 4-1. Doors 10/96 Doors Section Doors Page 4-1 Stepwell - Outward Opening Page 4-2 Doors Stepwell - Outward Opening Item Part Num. Number Qty. Description Notes 1 47001449 1 Trim - Step, Entrance, Diamond Plate 2 47001450

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 CAB KIT (p/n: KAF40-005WA and KAF40-005BA) NOTE: Hard sided doors are sold separately. This manual is the property of the owner.

More information

Bag 1. Bag 1. Center Pivot. Center Pivot

Bag 1. Bag 1. Center Pivot. Center Pivot 8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball

More information

42A FLB WOOD BUNKS 43A FLB ALUMINUM BUNKS ALUMINUM CANTILEVER BOAT LIFT

42A FLB WOOD BUNKS 43A FLB ALUMINUM BUNKS ALUMINUM CANTILEVER BOAT LIFT Page 1 of 9 42A --- 1265 FLB WOOD BUNKS 43A --- 1265 FLB ALUMINUM BUNKS ALUMINUM CANTILEVER BOAT LIFT Thank you for purchasing our product! Please read these instructions and follow them step by step.*

More information

Maintenance Information

Maintenance Information 80234313 Edition 1 June 2006 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing

More information

23-34 BODY COMPONENTS XJ VEHICLES J DOORS INDEX

23-34 BODY COMPONENTS XJ VEHICLES J DOORS INDEX 23-34 BODY COMPONENTS XJ VEHICLES J DOORS INDEX page Door Alignment Adjustment Major... 47 Door Alignment Adjustment Minor... 46 Door Edge Guard/Edge Protector Strip... 61 Door External Handle... 55 Door

More information

Maintenance Information

Maintenance Information 80234313 Edition 2 May 2014 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the

More information

Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent

Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent 1. Place the vehicle on a flat surface with blocks in front and behind the wheels preventing unwanted movement. The car

More information

Caution Improper installation could result in tape failure, mounting hardware, and reader. Please read instructions before installing!

Caution Improper installation could result in tape failure, mounting hardware, and reader. Please read instructions before installing! Elgo Sensor Mounting Motion High Speed Landing/Positioning System The encoded tape used for the landing system is suspended between two mounting brackets that attach to the car rail using forged clips

More information

Fisher 657 Diaphragm Actuator Sizes and 87

Fisher 657 Diaphragm Actuator Sizes and 87 Instruction Manual 657 Actuator (30-70 and 87) Fisher 657 Diaphragm Actuator Sizes 30 70 and 87 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Installation... 3 Mounting

More information

Midwest Industries, Inc. Ida Grove, IA Page 1

Midwest Industries, Inc. Ida Grove, IA Page 1 SSV40108HAC - Hydraulic Hoist with 120 Volt Pump SSV40108HDAC - Hydraulic Hoist, Deep Water, with 120 Volt Pump SSV40108HDC - Hydraulic Hoist with 12 Volt Pump SSV40108HDDC - Hydraulic Hoist, Deep Water,

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-049 Cab Enclosure MULE SX 3-4 Hours WARNING Improper installation of this accessory could result in an accident causing serious

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

Installation Instructions Pro Stick Shifter

Installation Instructions Pro Stick Shifter Installation Instructions Pro Stick Shifter Part Number 80701, 80702 & 80706 2012, 2010, 2008, 2001, 1998 by B&M Racing and Performance Products The B&M Pro Stick shifter #80701 and #80706 comes equipped

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Pg. 1 of 14 INSTALLATION & OWNER S MANUAL John Deere Gator XUV 825i S4 Cab (p/n: 1GTRXUV4 Steel Cab with Doors) The contents of this envelope are the property of the owner. Be sure to leave with the owner

More information

1.1 Quad Valve and Tri-Valve. Contents WATER DUMP BODY O-RING EXHAUST VALVE QUAD VALVE TIE WRAP EXHAUST MAIN BODY O-RING

1.1 Quad Valve and Tri-Valve. Contents WATER DUMP BODY O-RING EXHAUST VALVE QUAD VALVE TIE WRAP EXHAUST MAIN BODY O-RING Quad Valve and Tri-Valve Exhaust Assembly on Fiberglass Helmets Quad Valve and Tri-Valve Exhaust Contents QUAD-1 QUAD-2 QUAD-2 QUAD-2 QUAD-6 QUAD-7 1.1 Quad Valve and Tri- Valve Exhaust Assembly on Fiberglass

More information

Heavy Duty Miniature Quick-Change Applicator (End-Feed Type) with Mechanical or Air-Feed Systems

Heavy Duty Miniature Quick-Change Applicator (End-Feed Type) with Mechanical or Air-Feed Systems Heavy Duty Miniature Quick-Change Applicator (End-Feed Type) with Mechanical or Air-Feed Systems Instruction Sheet 408-8039 02 JUN 16 Rev G Ram Post Wire Disc Insulation Disc Insulation Crimper Stripper

More information

Installation Instructions - D-Series Warming Cabinet Instruction Door for Hinge UseReversal (Glass and Stainless Steel Doors)

Installation Instructions - D-Series Warming Cabinet Instruction Door for Hinge UseReversal (Glass and Stainless Steel Doors) Header Cam Lock Reversal... pg 1-4 Glass Door hinge reversal..... pg 5-9 Steel Door hinge reversal..... pg 10-13 Remove Panels Before reversing door hinges, the Header Cam Lock assembly must be reversed.

More information

Illustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN For a complete distributor & dealer list go to

Illustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN For a complete distributor & dealer list go to Illustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN 55060 For a complete distributor & dealer list go to www.gandy.net 36H13 36-inch Variable Rate Spreader Package Push Model w/13-inch

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # P2067

INSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # P2067 INSTALLATION INSTRUCTIONS GRILLE GUARD 07-14 TOYOTA TUNDRA 08-14 TOYOTA SEQUOIA PART # P2067 PARTS LIST: GRILLE GUARD 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left

More information

Deuce/Ace Installation Instructions

Deuce/Ace Installation Instructions HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"

More information

DOORS - REAR TABLE OF CONTENTS

DOORS - REAR TABLE OF CONTENTS 23-88 DOORS - REAR XJ DOORS - REAR TABLE OF CONTENTS page AIR EXHAUSTER...88....88 DOOR...89....89 DOOR GLASS...89....89 EXTERIOR HANDLE...89....89 HINGE...90....90 INSIDE HANDLE ACTUATOR...90....90 page

More information

EVO-1162 EVO Tailgate Tire Carrier

EVO-1162 EVO Tailgate Tire Carrier EVO-1162 EVO Tailgate Tire Carrier Bill of Materials EVO-1162 Tailgate Tire Carrier Part number Description Quantity EVO-12161 EVO Tailgate Tire Carrier 1 EVO-12162 Bolt Plate 1 EVO-12163 Wheel Mount 1

More information

Section 13. Tail Rotor Drive. RotorWay International A600 TALON Construction Manual. Section 13. Page A

Section 13. Tail Rotor Drive. RotorWay International A600 TALON Construction Manual. Section 13. Page A RotorWay International Page A Tail Rotor Drive Procedures covered in this section: Install driveshafts and gearboxes; install drive belt and tensioner; fabricate and install tail rotor pitch actuator arms;

More information

Falcon 5250 complete repair kit

Falcon 5250 complete repair kit Towing and Suspension Solutions 855010-02 08-14 Falcon 5250 complete repair kit part number 910003-55 This kit contains the components to replace the Falcon 5250 Autowlok button assemblies, collar shoulder

More information

Valtek Auxiliary Handwheels and Limit Stops

Valtek Auxiliary Handwheels and Limit Stops Valtek Auxiliary s and Limit Stops Table of Contents Page 1 General information 2 Installation 2 Side-mounted handwheels, size 25 and 50 (linear actuators) 3 Side-mounted handwheels, size 100 and 200 (linear

More information

(2) 10mm Quick Release Bolts with Pivot Washers (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts. (4) 10mm Plastic Washers

(2) 10mm Quick Release Bolts with Pivot Washers (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts. (4) 10mm Plastic Washers PARTS LIST: EXTREME GRILLE GUARD 1 Extreme Heavy Duty Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting Bracket 4 10mm x 24mm OD x 2.2mm Flat Washers

More information

DESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1.

DESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1. 2004 SUSPENSION Front - TSX DESCRIPTION NOTE: For system description and component location, see Fig. 1. Fig. 1: Identifying Front Suspension Components Wednesday, March 12, 2008 8:30:45 8:30:55 PM Page

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS KUBOTA GRAND L 30 SERIES HARD SIDED CAB ENCLOSURE (p/n 1KU3AS) SOFT SIDED CAB ENCLOSURE (p/n 1KU3SS) This Curtis Cab is designed and manufactured

More information

Installation Instructions

Installation Instructions COLONY/COLONY SOFT Bidet Faucet and Transfer Valve with Speed Connect Drain Congratulations on purchasing your American Standard faucet with the Speed Connect drain, a feature found only on American Standard

More information

XChange Seat Service and Maintenance Guide

XChange Seat Service and Maintenance Guide XChange Seat Service and Maintenance Guide Table Of Contents Page General Information... 1 Registration Information... 1 Seat Cushion Latch... 2 Lap Shoulder Belt Replacement... 2 Sliding Buckles Replacement...

More information

Heavy Duty Miniature Quick-Change Applicator (Side-Feed Type) with Mechanical or Air Feed Systems

Heavy Duty Miniature Quick-Change Applicator (Side-Feed Type) with Mechanical or Air Feed Systems Heavy Duty Miniature Quick-Change Applicator (Side-Feed Type) with Mechanical or Air Feed Systems Instruction Sheet 408-8040 30 NOV 17 Rev H Ram Assembly Ram Post Locking Screw Stock Drag Drag Release

More information

Contents. Section 5: Adjustments Ball Detect Adjustment Transport Band Tension Adjustment

Contents. Section 5: Adjustments Ball Detect Adjustment Transport Band Tension Adjustment Contents Section 5: Adjustments... 5-3 1. Ball Detect Adjustment... 5-3 2. Transport Band Tension Adjustment... 5-5 3. Transport Band Drive Belt Tension Adjustment... 5-7 4. Ball Cushion Adjustment...

More information

body interior Overview Driver s Seat

body interior Overview Driver s Seat body interior Overview The seating in your Blue Bird All American bus is designed for your safety and comfort. The placement and installation of school bus passenger seats is governed by federal regulations.

More information

S E R V I C E M A N U A L C C 3 0. Cooling System Major Components

S E R V I C E M A N U A L C C 3 0. Cooling System Major Components C C 3 0 C O O I N G Overview The cooling system on the Blue Bird Vision is designed to maintain the temperature of the engine within the optimum operating range, throughout the conditions for which the

More information

JEEP TJ & (XJ 84-01) ATLAS 2 SP.

JEEP TJ & (XJ 84-01) ATLAS 2 SP. KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 9 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302080 STUD BOLT 1/2"-13 X 7 (XJ) 3 1 303120 SERRATED LOCK NUT 1/2" X

More information

1. Remove the parking brake assembly. 2. Remove the 4 bolts holding the yoke flange and drum. Remove the yoke flange and drive.

1. Remove the parking brake assembly. 2. Remove the 4 bolts holding the yoke flange and drum. Remove the yoke flange and drive. Disassembly NOTE: To replace the brake assembly, brake shoe and lining assemblies, or other operational components the complete parking brake assembly must be removed from the vehicle. 1. Remove the parking

More information

Ram 1500 Crew Cab A Ram 2500/3500 Crew Cab A

Ram 1500 Crew Cab A Ram 2500/3500 Crew Cab A I N S T A L L A T I O N G U I D E APPLICATION AMP Part # Ram 1500 Crew Cab 2013-2015 77138-01A Ram 2500/3500 Crew Cab 2013-2015 77138-01A Note:The application works only on the Crew Cab model Vehicles.

More information

Yaw Control and Trim. 1. General. A. Yaw Control System. B. Yaw Trim System

Yaw Control and Trim. 1. General. A. Yaw Control System. B. Yaw Trim System CIRRUS AIRPLANE MAINTENANCE MANUAL MODELS SR AND SRT Yaw Control and Trim CHAPTER 7-0: YAW CONTROL AND TRIM GENERAL 7-0: YAW CONTROL AND TRIM. General This section describes that portion of the flight

More information

DESCRIPTION. 10" Square Valve 10" Valve for United Plastics Tank Valve Handle-Complete Assembly Auxilliary Handle Lock less Hardware (see page 12)

DESCRIPTION. 10 Square Valve 10 Valve for United Plastics Tank Valve Handle-Complete Assembly Auxilliary Handle Lock less Hardware (see page 12) QUIC-FLOW MANUAL DUMP VALVE ZICO 070PM REV 3-5- QUIC-FLOW valves are the fastest dumping systems for tankers, bar none, dumping up to 800 GPM. Mounting the valve at the bottom of the tank provides approximately

More information

CAB TILT HYDRAULIC SYSTEM

CAB TILT HYDRAULIC SYSTEM OPERATION, MAINTENANCE and SERVICE INSTRUCTIONS CAB TILT HYDRAULIC SYSTEM WITH POWER-PACKER PUMP, CYLINDERS and LATCHES A division of Actuant Corporation 1-800-745-4142 1 www.powerpackerus.com Notice The

More information

Installation Instructions Table of Contents

Installation Instructions Table of Contents Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft

More information

Assembly Manual. 1/10th Formula 1 Car

Assembly Manual. 1/10th Formula 1 Car Assembly Manual 1/10th Formula 1 Car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 *Note - Sometimes it is helpful to slightly over-tighten the top clamp

More information

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog# Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,

More information

Stowe Cargo Management System

Stowe Cargo Management System Installation Guide Stowe Cargo Management System Table of Contents 1. Pre-Installation (Page 2) a. Notes, Installation Kit contents & Tools needed 2. How to Install the Stowe Cargo Management System (Pages

More information

INSTALLATION MANUAL HYDRAULIC HOSE REEL

INSTALLATION MANUAL HYDRAULIC HOSE REEL INSTALLATION MANUAL HYDRAULIC HOSE REEL 1 TABLE OF CONTENTS SECTION PAGE SECTION PAGE 1 HOW TO ORDER PARTS 3 MAINTENANCE SCHEDULE... 11 1.1 HOW TO ORDER PARTS... 2 1.2 MODEL IDENTIFICATION... 3 2 INSTALLATION

More information

In area - A -, a proper seal must be made against the top of the window glass.

In area - A -, a proper seal must be made against the top of the window glass. Door window, adjusting Page 1 of 3 Audi > B3 > 1994-1998 Body Exterior, Interior 61 - Convertible top, checking and adjusting Door window, adjusting Sections C-C and D-D. Adjust door window so that window

More information

STEERING SYSTEM 6 A POWER STEERING

STEERING SYSTEM 6 A POWER STEERING STEERING SYSTEM 6 A 22147 POWER STEERING Table of Contents Page Specifications............................ 6A-1 Torque Specification................... 6A-1 Special Tools............................ 6A-1

More information

ZICO 2070PM1 REV Page 1

ZICO 2070PM1 REV Page 1 QUIC-FLOW Dump Valves Parts and Instruction Manual ZICO 070PM REV. 9-0- Zico dump valves are uniquely designed to stop annoying leakage. A special slotted hinge over the door shifts when in the closed

More information

BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt)

BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt) BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt) Install Time: Approx. 8-10 hrs Parts Needed: BBK Long Tube Headers Shorty mid pipe X/H O2 wiring harness extensions Hi-temp thread locker Tools Required:

More information

Installation Instructions Sport Shifter

Installation Instructions Sport Shifter The B&M Sport Shifter can be used in vehicles equipped with most popular three speed or four speed automatic transmissions. It is equipped with neutral safety and backup light switches, transmission brackets

More information

GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS

GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS -S INDICATES CYLINDERS ARE IN TANDEM PART NUMBER: 100121 REVISION "A" ECN

More information

ADVANCE ADAPTERS INC. P/N: JEEP TJ & (XJ 84-01) ATLAS 4 SPEED CABLE SHIFTER units built after 5/1/12

ADVANCE ADAPTERS INC. P/N: JEEP TJ & (XJ 84-01) ATLAS 4 SPEED CABLE SHIFTER units built after 5/1/12 Paso Robles, CA 93447 PAGE 1 OF 9 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-12-15 KIT CONSISTS OF: No. Qty Part No. Description 1 1 302051 BASE- TWIN STICK MOUNT 2 1 302080 STUD

More information

Times-2 Speed Files INSTALLATION INSTRUCTIONS

Times-2 Speed Files INSTALLATION INSTRUCTIONS Times-2 Speed Files INSTALLATION INSTRUCTIONS AURORA from RICHARDS-WILCOX, INC. 600 South Lake Street Aurora, Illinois 60506 Phone: 630-897-6951 Fax: 630-897-6994 Toll Free: 800-277-1699 TIMES-2 SPEED

More information

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: & Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.

More information

COLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: F10 M5 # D Fits: F06/F12/F13 M6 PARTS LIST

COLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: F10 M5 # D Fits: F06/F12/F13 M6 PARTS LIST COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0035 Fits: 2013-15 F10 M5 # D760-0037 Fits: 2012-15 F06/F12/F13 M6 PARTS LIST (1) Left Carbon Airbox Lid (1) Right Carbon Airbox Lid (1) Left Carbon Snorkel

More information

Section 5: Parts Replacement

Section 5: Parts Replacement Section 5: Parts Replacement Should the STAR TRAC 4500 Treadmill experience a problem requiring replacement of a specific part, the following procedures will help and instruct in the replacement of major

More information

Installation Instructions

Installation Instructions Installation Instructions ELECTRIC CONVERSION KIT 3 ALUMINUM ROLL TUBE IMPORTANT: This Electric Conversion Kit has been designed for systems with a 3 aluminum roll tube. It is assumed that the tarping

More information

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage

More information

NSGV EVE-ER I, O, & M MANUAL

NSGV EVE-ER I, O, & M MANUAL TABLE OF CONTENTS Rail Layout.. Page 1 Support Placement...Page 1 Rail Assembly.Page 1 Rail Duct Connections.. Page 2 Rubber Lip Installation.. Page 3 Pneumatic End Stop. Page 4 End Stop. Page 4 End Cap..

More information

Maintenance Information

Maintenance Information Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard

More information

INSTALLATION GUIDE STANDARD PRODUCT CODES:

INSTALLATION GUIDE STANDARD PRODUCT CODES: INSTALLATION GUIDE STANDARD PRODUCT CODES: 100, 105, 110, 111, 112, 113, 115, 120, 130, 140, 145, 146, 150, 200, 210, 240, 250, 255, 260, 300, 305, 405, 406, 407, 408, 425, 426, 435, 447, 500, 505, 510,

More information

920 Remote Control Switches

920 Remote Control Switches 920 Remote Control Switches REMOTE CONTROL SWITCHES Service Bulletin This service bulletin for ASCO 920 Remote Control Switches explains how to replace the main s, operator coil, control s, and how to

More information

Installation Instructions

Installation Instructions Installation Instructions TrailView Soft Top Important Safety Information For proper installation and best possible fit, please read all instructions BEFORE you begin. Periodically check all components

More information

(W) INSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA / SEQUOIA PART # &

(W) INSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA / SEQUOIA PART # & (W) INSTALLATION INSTRUCTIONS PART # 501894 & 501895 PARTS LIST: 1 Grille Guard 4 3/8" Flat Washers 1 Driver/Left Frame 2 3/8" Nylon Lock Nuts 1 Passenger/Right Frame 4 12mm Plastic Washers 1 Driver/Left

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL This Curtis Cab is designed and manufactured for use only as reasonable weather protection. This cab is not applicable, Nor should the cab be considered as protection against

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # 2067/2067-2

INSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # 2067/2067-2 INSTALLATION INSTRUCTIONS 07-15 TOYOTA TUNDRA 08-15 TOYOTA SEQUOIA PART # 2067/2067-2 PARTS LIST: 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting

More information

BETTIS ACTUATOR & CONTROLS SERVICE INSTRUCTIONS FIELD CONVERSION OF SPRING CARTRIDGE FAIL DIRECTION CLOCKWISE TO COUNTER-CLOCKWISE OR THE INVERSE

BETTIS ACTUATOR & CONTROLS SERVICE INSTRUCTIONS FIELD CONVERSION OF SPRING CARTRIDGE FAIL DIRECTION CLOCKWISE TO COUNTER-CLOCKWISE OR THE INVERSE BETTIS ACTUATOR & CONTROLS SERVICE INSTRUCTIONS FIELD CONVERSION OF SPRING CARTRIDGE FAIL DIRECTION CLOCKWISE TO COUNTER-CLOCKWISE OR THE INVERSE FOR THE FOLLOWING SERIES T3XX-SRX AND T4XX-SRX SPRING RETURN

More information

DARMAN. ENDURA II Cloth Towel Cabinet Product Guide. Manufacturing Company, Inc Lincoln Ave., Utica, NY 13502

DARMAN. ENDURA II Cloth Towel Cabinet Product Guide. Manufacturing Company, Inc Lincoln Ave., Utica, NY 13502 ENDURA II Cloth Towel Cabinet Product Guide Page 2, 3 4, 5 6, 7 8, 9 10 11 12 Parts Covered Hood Assembly Mechanism Back Assembly Bin and Towel Guide Service Bulletin - Roller Warranty and Maintenance

More information

E-LIFT II+ SYSTEM WITH SPRING LEVER FOR A-SERIES AND FULL FRAME LOOMS

E-LIFT II+ SYSTEM WITH SPRING LEVER FOR A-SERIES AND FULL FRAME LOOMS Congratulations on your purchase of the E-Lift II+ system. This system replaces the action of treadling, eliminating leg strain and fatigue. When you activate the Foot Switch, the motor turns, and selected

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 TRANS 4 FRONT CAB KIT (p/n: KAF40T-001WA and p/n: KAF40T-001BA) NOTE: Hard sided doors, soft sided doors, and rear cab are sold

More information

1209A GM B-BODY Double Adjustable Trailing Arms

1209A GM B-BODY Double Adjustable Trailing Arms 1209A 78-96 GM B-BODY Double Adjustable Trailing Arms Warning: This installation should be performed by a trained professional. Tools Required for this Installation - 4 post lift or alignment rack preferable

More information

Instruction Guide: Infiniti Q50 3.0L VR30DDTT "Full Down Pipes"

Instruction Guide: Infiniti Q50 3.0L VR30DDTT Full Down Pipes 480 E. Easy St. Unit #4 Simi Valley, Ca. 93065 Instruction Guide: 2016+ Infiniti Q50 3.0L VR30DDTT "Full Down Pipes" Technical support: (805) 522-3278 Monday- Friday 9a.m.- 3 p.m. PST WARNING: INSTALLATION

More information

1. Open front door (20124) and support using Rotunda Flexi-Work Table or equivalent.

1. Open front door (20124) and support using Rotunda Flexi-Work Table or equivalent. file://c:\tso\tsocache\vdtom_3244\svk~us~en~file=svk13002.htm~gen~ref.htm Page 1 of 6 Section 01-03: Doors and Liftgate REMOVAL AND INSTALLATION 1997 Aerostar, Ranger Workshop Manual Doors Front Doors

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL MODEL SR0 YAW CONTROL AND TRIM. GENERAL This section describes that portion of the flight control system which controls the position and movement of the rudder. Included are; rudder system rigging, rudder

More information

Fabric Replacement Top Without Upper Doors

Fabric Replacement Top Without Upper Doors Fabric Replacement Top Without Upper Doors Installation Guidelines For: 1997-2002 Jeep Wrangler TJ w/factory Frame PN: 10-40-TJ19702!!STOP!! Before proceeding make sure the top is the correct item for

More information

Assembly Manual. 1/10th World GT car

Assembly Manual. 1/10th World GT car Assembly Manual 1/10th World GT car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the

More information

Installation Instructions

Installation Instructions TROPIC Spread Lavatory Faucet with EverClean Finish & SpeedConnect Drain Installation Instructions 708.80 Congratulations on purchasing your American Standard faucet with EverClean finish and Speed Connect

More information

Maintenance Information

Maintenance Information 04581245 Edition 2 May 2014 Air Grinder, Die Grinder and Sander Series G2 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,

More information

Safety First. Please remember to always use SAFE shop practices when performing all service procedures.

Safety First. Please remember to always use SAFE shop practices when performing all service procedures. Safety First Please remember to always use SAFE shop practices when performing all service procedures. 2006 Update Manual January 2006 Country Clipper 2006 Update Manual Index Joystick Kill Switch Oil

More information

SECTION 3 BODY STYLES BODY VENTILATION ALL STYLES EXCEPT "E" INDEX. SHROUD SlDE FINISHING PANEL AND. SHROUD SlDE FINISHING PANEL

SECTION 3 BODY STYLES BODY VENTILATION ALL STYLES EXCEPT E INDEX. SHROUD SlDE FINISHING PANEL AND. SHROUD SlDE FINISHING PANEL SECTION 3 FRONT END 3-1 Subject Page Body Ventilation - All Except "E" Styles... 3-1 Shroud Side Finishing Panel... 3-1 Shroud Side Air Outlet... 3-1 Shroud Side Finishing Panel and Air Outlet Duct Assembly...

More information

155A 2500 LB. Gear Drive Winch ALUMINUM NARROW PONTOON LIFT

155A 2500 LB. Gear Drive Winch ALUMINUM NARROW PONTOON LIFT 05/31/05 Page 1 of 7 155A 2500 LB. Gear Drive Winch ALUMINUM NARROW PONTOON LIFT Thank you for purchasing a PORTA-DOCK product. *Please read these instructions and follow them step by step.* STEP 1. Locate

More information

PORTA-DOCK, INC. 100A 1200 LB. 84 WIDE ALUMINUM CANTILEVER BOAT LIFT 102A 1200 LB. 113 WIDE ALUMINUM CANTILEVER BOAT LIFT

PORTA-DOCK, INC. 100A 1200 LB. 84 WIDE ALUMINUM CANTILEVER BOAT LIFT 102A 1200 LB. 113 WIDE ALUMINUM CANTILEVER BOAT LIFT Page 1 of 7 PORTA-DOCK, INC. 100A 1200 LB. 84 WIDE ALUMINUM CANTILEVER BOAT LIFT 102A 1200 LB. 113 WIDE ALUMINUM CANTILEVER BOAT LIFT Thank you for purchasing our product! Please read these instructions

More information

Maintenance instruction

Maintenance instruction Maintenance instruction This maintenance instruction is a step-by-step instruction for service and maintenance on Stafsjö s HG valve. Same procedure also applies for HL, HP and HPT. The instruction shall

More information

Installation Instructions I - Sheet Number I-TVR-01 Rev. A

Installation Instructions I - Sheet Number I-TVR-01 Rev. A Installation Instructions I - Sheet Number I-TVR-01 Rev. A TrailView Soft Top For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to

More information