POLARIS XLT 580/600 INSTALLATION INSTRUCTIONS PART # READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET
|
|
- Gregory Malone
- 5 years ago
- Views:
Transcription
1 Page 1 of 6 POLARIS XLT 580/600 INSTALLATION INSTRUCTIONS PART # READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET 1. Remove stock exhaust, y-pipe, front and rear muffler support. 2. Install three exhaust flanges, marked "C" for center, "P" for PTO, "M" for mag. 3. Install mag (right) side suspension tower heat shield (small formed steel plate). Position this plate on forward edge of suspension tower 2 1/2" inward from outer forward edge of suspension tower (ILL 1). Mark and drill 3/16" holes and rivet in place. 4. Position PTO (left) side heat shield as per ILL 2, mark and drill 3/16" holes. Rivet in place with small head 3/16" rivets. NOTE: For 1996 RMK models, do not use the aluminum (PTO side) heat shield. Use three 7" strips of adheasive backed insulating tape. Apply this tape to the PTO side shock tower as shown in illustration 7. To ensure best adhesion, insure that the area is clean and free from oil. 5. Wire loom and speedo cable relocation: Remove speedo cable and wire loom from instrument pod, remove aluminum wire loom clip from windshield base and re-install on left side of belly pan with 3/16" rivet (ILL 3). With 1 3/4" hole saw, open all four holes in nose plate. Re-route wire loom and speedo cable under wire loom clip on left side of belly pan, through nose plate (2nd hole form left), then up the center of the hood between louvers. Re-connect loom and cable to instrument pod. Using 1 nylon tie, secure loom and cable to windshield o-ring (left front). If louver screen kit is not installed, drill two 3/32" pilot holes in screen mount in hood. Install loom/cable support as previously stated using two screws provided. NOTE: To prevent heat damage, cover wire loom and speedo cable with reflective heat tape provided in area's closet to pipe. 6. Remove smalll coolant line at water pump inlet to check valve and replace it with longer line provided. Re-route line down and under starter housing. Secure line with tie strap provided to wire loom as per ILL 4. WARNING: WATER LINE SHOUD BE COVERED WITH REFLECTIVE HEAT TAPE IN AREA CLOSEST TO THE PIPE. 7. IMPORTANT NOTE: The bolt connecting steering drag link to bellcrank must be installed with bolt head up to allow clearance between center pipe and bolt. 8. Pipe installation: Head pipe is marked to identify location. Install mag (right) pipe first (marked "M"), center pipe second (marked "C"), and PTO (left) pipe third (marked "P"). Place OEM rubber antivibration insulator into mount on silencer (ILL 5) and install silencer (ILL 6). NOTE: On 93 and 94 model's, it may be necessary to remove.350" from end of vibro-insulator for proper hood to silencer clearence.
2 Page 2 of 6 NOTE: Insure that cylinder flange rings do not bind when installing pipes. Place ring end gaps 180 degrees from each other. 9. Spring installation: Seven short and two long springs are supplied with the kit. Six short springs connect cylinder flanges to pipes, one long spring hooks to the front of the center pipe and connects to the obround hole in the aluminum nose plate. One short spring connects the center head pipe to the PTO pipe mid section. Use the OEM springs for silencer to pipe connection. LUBRICATION: TUNING INSTRUCTIONS Oil Injection Adjustment: Injection arm adjustment at the full throttle position - the alignment mark should be advanced by 1-2 mm. This will allow slightly more oil delivery. Oil Recommendations: For high performance trail applications use SLP brand XPT oil. FOR XLT WITH STOCK ENGINE AND CARBS NOTE: Air box in place and unaltered. Located by the gauges on top of the hood is the air intake plate. Between the plate and hood is a piece of foam, this foam should be removed and the plate re-installed. Elevation -20 & Below -20 to to & Above ' ' ' * ' * 160* *Marked altitudes should drop Jet Needle on position (raise E clip). MAIN JET NOTE: MAG CYLINDER ON SOME SLEDS (MOST COMMON ON 1993 MODELS) REQUIRES ONE SIZE LARGER MAIN JET THAN THE ABOVE CHART. PLUG COLOR WILL BE EVEN ON EACH CYLINDER WHEN CORRECT. Pilot Jet ft: #35, 5000 ft. & Higher: #35 Needle Jet ft: #166-Q2 (stock), 5000 ft. & Higher: #166-Q0 Jet Needle - 6DP17-3 (stock), 95 XLT 600 6DH17-3 (stock) Slide Cut Away (stock) TRAIL PORTED ENGINES: XLT with SLP trail porting, stock 34 mm carbs and SLP pipes. Use the above tuning chart and increase main jet size by one and richen needle clip by one position.
3 Page 3 of 6 FOR XLT 580 WITH STOCK ENGINE WITH 38 mm ROUND SLIDE CARBS NOTE: Air box in place and unaltered. Located by the gauges on top of the hood is the air intake plate. Between the plate and hood is a piece of foam, this foam should be removed and the plate re-installed. Elevation -20 & Below -20 to to & Above ' ' ' ' MAIN JET NOTE: MAG CYLINDER ON SOME SLEDS (MOST COMMON ON 1993 MODELS) REQUIRES ONE SIZE LARGER MAIN JET THAN THE ABOVE CHART. PLUG COLOR WILL BE EVEN ON EACH CYLINDER WHEN CORRECT. Pilot Jet - #45 Needle Jet ft: 247 Q-0, 5000 ft. & Higher: 247 P-8 Jet Needle - 6DP10-3 Slide Cut Away Air Screw turn BORED 38 mm ROUND SLIDE CARBS TO 39.2 mm: Increase Main Jet by One size over the above chart. FOR 1996 XLT RMK WITH ACCS -20 & Below -20 to to & Above Pilot Jet - #35 Needle Jet Q-0 Jet Needle - 6DP17-3
4 Page 4 of 6 FOR 1997 XLT RMK WITH ACCS -20 & Below -20 to to & Above Pilot Jet - #50 Needle Jet P-2 Jet Needle - 6EJ3-2 Air Screw - 3/4 turn Running RPM Elevation: ft. Primary Spring - Blue, # Primary Weight - 10M White, # Secondary Spring - Red, #3 hole Helix - Stock (*) Elevation: ft. Primary Spring - Blue, # Primary Weight - 10M Red, # Secondary Spring - Red, #3 hole Helix - Stock (*) Elevation: 6000 ft. & Above Primary Spring - Gold, # Primary Weight - P-1 w/ 40-4 Max clips, # Secondary Spring - Red, #3 hole Helix - Stock (*) CLUTCH TUNING FOR XLT 580/600 WITH SLP PIPE SET (*) Optional Multi-Angle Helix: May be used for additional acceleration ft. altitude, use a 40/36, SLP #40-40/36. For 3000 and higher altitude, use a 38/34 helix, SLP #40-38/34. With all multiangle helixes the SLP #40-3 Black driven spring must be used. The 40-3 Black spring will also improve performance with the stock helix. IMPORTANT NOTES: Failure to perform the following adjustments could cause loss of performance and ''boggy'' low end power. 1. Belt side clearance. Be sure the belt side clearance is not excessive. Recommended.010" to.030" between belt and clutch face. Re-shim spider if needed. Excessive clearance may cause a low end bog. 2. Type of belt. Use only SLP-approved performance belts or stock Polaris brand belts.
5 Page 5 of 6 3. Belt free-play. Proper belt free-play is very important. To achieve best performance, driven shims can be added or subtracted (or cam cam adjust tightened) to adjust belt as tight as possible without creeping at an idle. 4. Gearing. We do not recommend gearing lower than 19/39 with the above clutch specs. If lower gearing must be used, it will be necessary to increase the weight of the primary cam arms. IGNITION TIMING Ignition timing should be checked for best performance. Timing should be 20 degrees at 7500 RPM, 28 degrees at 3000 RPM ± 1 degree. High RPM timing is most important. Refer to Polaris service information for proper timing procedure. ILLUSTRATIONS
6 Page 6 of 6 Starting Line Products, Inc. (208) slp@slp.cc
XLT SPECIAL TRIPLE PIPE SET P.N Installation Instructions
1995-97 XLT SPECIAL TRIPLE PIPE SET P.N. 09-598 Installation Instructions Revised 8/20/02 Read instructions carefully before installation 1 - Remove stock exhaust, Y-Pipe, front and rear muffler support.
More informationXCR 600/ XLT TRIPLE PIPE SET P.N Installation Instructions
1994-97 XCR 600/1993-97 XLT TRIPLE PIPE SET P.N. 09-5970 Installation Instructions Read instructions carefully before installation 1-Remove stock exhaust, Y-pipe, and rear muffler support. 2-Install three
More informationPOLARIS XLT-SPECIAL TRIPLE PIPE SET P.N
1998-99 POLARIS XLT-SPECIAL TRIPLE PIPE SET P.N. 09-596 Important: Read instructions carefully before installation. 1-Remove stock exhaust, Y-pipe, and rear muffler support. 2-Install three exhaust flanges,
More informationSLP PIPE INSTALLATION INSTRUCTIONS POLARIS ULTRA 680 SP SKS & RMK P.N (Read instructions carefully before installation.
SLP PIPE INSTALLATION INSTRUCTIONS POLARIS 1996-97 ULTRA 680 SP SKS & RMK P.N. 09-6802 (Read instructions carefully before installation.) NOTE: The Ultra has proven to exhibit distinct personalities from
More informationSLP PIPE INSTALLATION INSTRUCTIONS POLARIS ULTRA 680 SP SKS & RMK P.N (Read instructions carefully before installation.
SLP PIPE INSTALLATION INSTRUCTIONS POLARIS 1996-97 ULTRA 680 SP SKS & RMK P.N. 09-6801 (Read instructions carefully before installation.) NOTE: The Ultra has proven to exhibit distinct personalities from
More informationPOLARIS 700 XC/SKS/RMK SLP TWIN PIPE SET P.N
POLARIS 700 XC/SKS/RMK SLP TWIN PIPE SET P.N. 09-710 IMPORTANT: Read instruction carefully before installation. For engines with stock porting use either 09-700 glass pack pipe set or 09-710 canister pipe
More informationSLP PIPE INSTALLATION INSTRUCTIONS #09-9 & # & NEWER POLARIS INDY 650 & RXL PIPE SET EFFECTIVE 6-92
Page 1 of 5 SLP PIPE INSTALLATION INSTRUCTIONS #09-9 & #09-10 1988 & NEWER POLARIS INDY 650 & RXL PIPE SET EFFECTIVE 6-92 READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET #09-9 (For stock
More informationPOLARIS Twin 600/700 SINGLE PIPE SET P.N
1997-1998 POLARIS Twin 600/700 SINGLE PIPE SET P.N. 09-718 Important: Read instruction carefully before installation. Note: Do not remove banding placed on the mid section of the pipe. It has been placed
More informationSingle Pipe Set with OEM Silencer for /800 RMK/XC, /800 SKS, /800 Switchback and Switchback
Single Pipe Set with OEM Silencer for 2002-05 700/800 RMK/XC, 2003 700/800 SKS, 2004 700/800 Switchback and 2005 800 Switchback P.N. 09-836 Important: Read instructions carefully before installation. Note:
More informationPOLARIS 700/800 PRO X SINGLE PIPE P.N
2003-04 POLARIS 700/800 PRO X SINGLE PIPE P.N. 09-839 Important: Read instructions carefully before installation. Note: Do not remove banding placed on the mid section of the pipe. It has been placed there
More informationSingle Pipe Set for Big Block: /700 XC/SKS/RMK and /700 RMK/SKS For use with Stock Silencer P.N
Single Pipe Set for Big Block: 2000 600/700 XC/SKS/RMK and 2001 600/700 RMK/SKS For use with Stock Silencer P.N. 09-732 Important: Read instruction carefully before installation. Note: Removal of pipe
More informationSinlge Pipe for /800 Pro-X/Pro-X2/Pro-XR P.N
Sinlge Pipe for 2003-04 700/800 Pro-X/Pro-X2/Pro-XR P.N. 09-9 Important: Read instructions carefully before installation. Note: Do not remove banding placed on the mid section of the pipe. It has been
More informationSLP Single Pipe for Polaris 600 H.O. Fusion/RMK/Switchback/Shift (Carb Models)
SLP Single Pipe for 2006-09 Polaris 600 H.O. Fusion/RMK/Switchback/Shift (Carb Models) Part # 09-634 Kit Contents: 2-7 Insulated Heat Tape 1-1/8 Pipe Adjustment Washer 4-30 Reflective Heat Tape 1 - Wire
More information1-Remove stock exhaust, Y-Pipe, and silencer (Retain OEM springs and exhaust gaskets for pipe installation).
Single Pipe Set for use with Performance Edition Kit for 2003-04 POLARIS 800 Pro X P.N. 09-848 Important: Read instructions carefully before installation. Note: Do not remove banding placed on the mid
More informationSLP Twin Pipes for 2004 Arctic Cat 900 Mountain Cat Twin P.N (CP)
Setting the World s Performance Standards Twin Pipes for 2004 Arctic Cat 900 Mountain Cat Twin P.N. 09-907(CP) Contents of Pipe Set 1 - Plastic Zip tie 3 - Large Head Rivets 4 - Short s 1 - Red Silicone
More informationSLP Twin Pipes for 2003 Arctic Cat 900 Twin
Setting the World s Performance Standards SLP Twin Pipes for 2003 Arctic Cat 900 Twin P.N. 09-902(CP) and 09-903(CP) IMPORTANT: Read instructions carefully before installation. 1. Remove stock exhaust,
More informationSLP Single Pipe Set for Arctic Cat 900 Mountain Cat Carb and EFI with Transfer Outlet Tube P.N CP/09-914CP
Setting the Wld s Perfmance Standards SLP Single Pipe Set f 2004-05 Arctic Cat 900 Mountain Cat Carb and EFI with Transfer Outlet Tube P.N. 09-908CP/09-914CP Read instructions carefully and completely
More information3- Remove stock silencer bracket from the bulkhead located above brake assembly (this bracket will not be used in installation).
SLP Single Pipe Set for 2004 ZR 900 P.N. 09-904CP Kit Contents: 2 1/4 Flat Washer 2 Large Head Rivets 2 1/4 Nylock Nuts 2 Rivet Washers 1 Stem Vibro Support 1 Medium Sping 1 pc 30 Reflective Heat Tape
More informationSLP PART # ATTENTION DEALER
PART #09-8000 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION AND INSTRUCTION DATA THAT IS SUPPLIED IN THIS PACKET FOR THIS PRODUCT. Before you begin, please read the following: The
More informationSLP PART # ATTENTION DEALER
SLP PART #09-872 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION AND INSTRUCTION DATA THAT IS SUPPLIED IN THIS PACKET FOR THIS PRODUCT. Before you begin, please read the following:
More informationPart # SLP Single Pipe Set for G4 Ski Doo 850
Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Part # 09-867 SLP Single Pipe Set for 2017-18 G4 Ski Doo 850 Parts List: 7-7 Insulated
More informationSLP PART # ATTENTION DEALER
SLP PART #09-883 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION AND INSTRUCTION DATA THAT IS SUPPLIED IN THIS PACKET FOR THIS PRODUCT. Before you begin, please read the following:
More informationSingle Pipe for Ski-Doo REV H.O. (For use with ported engines only) #09-870
the World s Performance Standards Single Pipe for 200-2006 Ski-Doo REV H.O. (For use with ported engines only) #09-870 Important: Read instructions carefully before installation. 1. Remove stock pipe and
More information... TX-L MODEL NUMBER CONTENTS 2-3 BODY. 4-6 HOOD ASSEMBLY IGNITION ASSEMBLY. 8-9 SEAT ASSEMBLY STEERING ASSEMBLY.
.. ~ : l~ :;~, ~ 0 J-I-'olaris I I '. ... TX-L MODEL NUMBER 080639 CONTENTS BODY. HOOD ASSEMBLY IGNITION ASSEMBLY. SEAT ASSEMBLY... STEERING ASSEMBLY. CHAINCASE ASSEMBLY. DRIVE CLUTCH. DRIVEN CLUTCH. DRIVE
More informationRevised 10/22/2014 Page 2 of?
1.Remove side panels, hood, seat, fuel tank, and 2.Remove stock air box, remove fuel line muffler. Save exhaust springs and rubber muffler mounts for turbo bracket. Sand back surface flat for mounting.
More informationSLP PART# ATTENTION DEALER
*015-09866* Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 PART# 09-866 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION
More informationPart # SLP Silencer for G4 Ski Doo 850
Part # 09-867 SLP Silencer for 2017-18 G4 Ski Doo 850 Parts List: 7-7 Insulated Heat Tape (Part #090-29) 5-30 Reflective Heat Tape (Part #090-31) 1 - Inner Aluminum Heat Shield (Part #091-6057) 3-3/16
More informationPolaris Axys Sidekick Installation Instructions
2016-2017 Polaris Axys Sidekick Installation Instructions 1. Remove hood and side panels. 2. Remove fasteners and slide console back. 3. Remove belt and driven clutch. 4. Remove clutch cover/ oil-tank
More informationCS340ES. Property of - Not for Resale A1
A1 CYLINDER HEAD - CYLINDER 1 8G8-11111-00-00 HEAD, CYLINDER 1......... 1 2 8G8-11121-00-00 HEAD, CYLINDER 2......... 1 3 NGK-BR9ES-00-00 PLUG, SPARK............. 2 4 8G8-11181-01-00 GASKET, CYLINDER HEAD
More informationSLP Stage 2 Performance Kit for Polaris 800 Axys
Setting the World s Performance Standards 743 E. Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Stage 2 Performance Kit for 2015-17 Polaris 800 Axys The following tuning specification
More informationSetting the World s Performance Standards
Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Lightweight Silencer for Polaris: 2016-17 800 Axys Models & 2017 600 Pro-RMK P/N 09-322
More informationSLP Single Pipe Set for 2007 Arctic Cat M1000
Single Pipe Set for 2007 Arctic Cat M1000 P.N. 09-876 Kit Contents: 1 - Silencer 1 - Spring Tab 1 - Large Head Rivet 1 - Short Spring 1 - Zip Tie 1-30 Reflective Heat Tape 1 - Y-Pipe 1 - Single Pipe Read
More informationTX-L MOD EL NUMBER CONTENTS
TX-L MOD EL NUMBER 080639 CONTENTS BODY. HOOD ASSEMBLY IGNITION ASSEMBLY. SEAT ASSEMBLY... STEERING ASSEMBLY. CHAINCASE ASSEMBLY. DRIVE CLUTCH. DRIVEN CLUTCH. DRIVE SHAFT.. TRACK ASSEMBLY. MAIN WIRE HARNESS
More informationSV125EP. Not For Resale
A1 CYLINDER 1 50W-11111-00-00 HEAD, CYLINDER 1......... 1 2 87A-11181-00-00 GASKET, CYLINDER HEAD... 1 3 NGK-BR8HS-00-00 PLUG, SPARK............. 1 4 87A-11311-00-00 CYLINDER 1.............. 1 5 50W-11351-00-00
More informationClasses INC. Northeast Snowmobile Racing INC SNOW DRAG RACING. Classes. Amateur: ( $15 Entry Fee + $5 Insurance Fee) Stock: 500, 600, 700, 800, Open
INC Northeast Snowmobile Racing INC Classes SNOW DRAG RACING Classes Amateur: ( $15 Entry Fee + $5 Insurance Fee) Stock: 500, 600, 700, 800, Open Improved Trail: 500, 600, 700, 800, Open Pro: ( $25 Entry
More informationSkidoo XM Etec Installation Instructions
Thank you for purchasing your Silber Turbo kit. This product was designed to give you endless amounts of power and satisfaction. During the installation feel free to call us with any question or concerns
More informationRevised 10/23/2015 Page 2 of 10
1.Remove the gauge, side panels, hood and headlight. Remove the air box from the throttle bodies then remove the seat and gas tank. 2.Carefully remove temp sensor from air box using a small pick or screw
More informationAC 120 MODEL NUMBER S2008ACAAAUSG MODEL NUMBER S2008ACAAAUSP
2008 AC 120 Illustrated Parts Manual MODEL NUMBER S2008ACAAAUSG MODEL NUMBER S2008ACAAAUSP TABLE OF CONTENTS (Model No. S2008ACAAAUSG) (Model No. S2008ACAAAUSP) SKI AND SPINDLE ASSEMBLY... 1 A-ARM ASSEMBLY...
More informationClutching for 2019 Polaris 850 RMK
Clutching for 2019 Polaris 850 RMK Important: The following clutching information has been thoroughly tested and is highly recommended for proper performance and reliability. Primary weights, drive spring
More informationMTNTKperformance.com. '16-Current Polaris AXYS 800 Intercooled Turbo Kit Install Instructions
1 '16-Current Polaris AXYS 800 Intercooled Turbo Kit Install Instructions '16-Current Polaris AXYS 800 Intercooled Turbo Kit Install Instructions 1. Remove: side panel, hood, seat, fuel tank, muffler,
More informationIllustrated Parts Manual M5 2. Model Number S2005M5CICUSG Model Number S2005M5CICUSB Model Number S2005M5CICOSG
Illustrated Parts Manual M5 2 Model Number S2005M5CICUSG Model Number S2005M5CICUSB Model Number S2005M5CICOSG 00 5 TABLE OF CONTENTS 2005 M5 (Model No. S2005M5CICUSG) (Model No. S2005M5CICUSB) (Model
More informationCYLINDER HEAD - CYLINDER
A1 CYLINDER HEAD - CYLINDER 1 8AY-11111-00-00 HEAD, CYLINDER 1......... 1 2 8A7-12499-00-00 JOINT................... 1 3 NGK-BR9ES-00-00 PLUG, SPARK............. 2 4 8AY-11181-00-00 GASKET, CYLINDER HEAD
More informationWorld Formula TECH MANUAL
World Formula TECH MANUAL Section 1 General Rules 1. Only stock Briggs & Stratton World Formula Model # 124435-8101 will be used in this class except as provided in this Tech manual. All parts will be
More informationIllustrated Parts Manual
ARCTIC CAT SHARE OUR PASSION. TM Illustrated Parts Manual AC 120 Model Number S2007ACAAAUSG Model Number S2007ACAAAUSO 2007 TABLE OF CONTENTS 2007 AC 120 (Model No. S2007ACAAAUSG) (Model No. S2007ACAAAUSO)
More informationELECTRIC START KIT KIT P/N
ELECTRIC START KIT KIT P/N 2873876 Application 2002 Polaris EDGE Models with 500-600 Domestic Engines Before you begin, read these instructions and check to be sure all parts and tools are accounted for.
More informationCHAIN SAWS G561AVS G621AVS
2626-93121 CHAIN SAWS G561AVS G621AVS APPLICABLE SERIAL NUMBERS: OCTOBER 1998 G561AVS 814608 and up G621AVS 820954 and up Fig.1 1 Fig.2 2 Fig.1 1 1 2616-12112 2618-12115 CYLINDER 1 K4 2 3356-12141 GROMMET
More informationBA /02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07)
BA-2020-00/02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07) Page: 1 Revision: 6.2-02/23/2011 Install Time: 1.5 Hours We recommend a qualified Yamaha technician install this kit
More informationELECTRIC START KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6. All Polaris Pro-Ride Snowmobiles
ELECTRIC START KIT P/N 2879330 APPLICATION All Polaris Pro-Ride Snowmobiles BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationIllustrated Parts Manual
2010 Illustrated Parts Manual 120 Sno Pro Model Number S2010ACAAAUSG SHARE OUR PASSION ṬM TABLE OF CONTENTS 2010 120 Sno Pro (Model No. S2010ACAAAUSG) SKI AND SPINDLE ASSEMBLY... 1 A-ARM ASSEMBLY... 2
More informationSno Pro 120. Model Number S2012ACAAAUSG SHARE OUR PASSION.
2012Snowmobile Illustrated Parts Manual Sno Pro 120 Model Number S2012ACAAAUSG TM SHARE OUR PASSION. TABLE OF CONTENTS 2012 Sno Pro 120 (Model No. S2012ACAAAUSG) SKI AND SPINDLE ASSEMBLY... 1 A-ARM ASSEMBLY...
More informationPOLARIS MARINE 1200 Model #W000099D Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /00
POLARIS MARINE 00 Model #W000099D 000 Polaris Sales Inc. PARTS MANUAL PN 9968 and MICROFICHE PN 9969 /00 TABLE OF CONTENTS POLARIS MARINE 00 W000099D Parts Manual A AIR VENT...........................
More informationHW Prowler Carburetor Installation Instructions
HW Prowler Carburetor Installation Instructions Page 1 of 6 Carb Kit Contains: HW modified Mikuni 36mm pumper style carb Custom choke cable Fuel Line Clamp Instructions (2) Leaner and (2) richer main jets
More informationIllustrated Parts Manual. ZR 120 Model Number S2005ZRAAAUSG Model Number S2005ZRAAAUSR
Illustrated Parts Manual ZR 120 Model Number S2005ZRAAAUSG Model Number S2005ZRAAAUSR 2 00 5 TABLE OF CONTENTS 2005 ZR 120 (Model No. S2005ZRAAAUSG) (Model No. S2005ZRAAAUSR) SKI AND SPINDLE ASSEMBLY.................................................
More information5 Large spring 1. Key Start Kit Workman MDX Utility Vehicle. Preparing the Machine. Loose Parts. No Parts Required. Procedure
Key Start Kit Workman MDX Utility Vehicle Model No. 119-9534 Form No. 3366-100 Rev B Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position.
More informationStock rubber isolator must remain in this location
*015-09319* Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Lightweight Silencer for Polaris: 2015-18 800 Axys Models & 2016-18 600
More informationZR 120 Model NumberS2003ZRAAAUSG
ARCTIC CAT ZR 120 Model NumberS2003ZRAAAUSG TABLE OF CONTENTS 2003 ZR 120 - Revised (Model No. S2003ZRAAAUSG) SKI AND SPINDLE ASSEMBLY................................................. 1 A-ARM ASSEMBLY..........................................................
More informationELECTRIC START KIT KIT P/N
ELECTRIC START KIT KIT P/N 2879330 Application All Polaris Pro-Ride Snowmobiles Before you begin, read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More informationArctic Cat ProClimb Sidekick Installation Instructions
2013-2017 Arctic Cat ProClimb Sidekick Installation Instructions 1.Remove side panels, front bumper, and hood 2. Remove pipe, muffler, heat shield and ECU 3. Remove cross brace. Unplug the servo motor
More informationModel No. S2002ZRAAAUSG ILLUSTRATED PARTS MANUAL
A RC TI C C A T 2002 ZR 120 Model No. S2002ZRAAAUSG ILLUSTRATED PARTS MANUAL TABLE OF CONTENTS 2002 ZR 120 (Model No. S2002ZRAAAUSG) SKI AND SPINDLE ASSEMBLY.................................................
More informationTRAIL BLAZER 250 Model #A03BA25CA. E 2002 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /02
TRAIL BLAZER 0 Model #A0BACA E 00 Polaris Sales Inc. PARTS MANUAL PN 0 and MICROFICHE PN 0 /0 This page left blank intentionally. TABLE OF CONTENTS Trail Blazer A0BACA Parts Manual A- ARM... B AIR BOX...
More informationTRAIL RMK 136 Model #S02SR5BS. E 2001 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /01
TRAIL RMK Model #S0SRBS E 00 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /0 This page left blank intentionally. ACCS... AIR BOX... BLOWER HOUSING... BRAKE... CARBURETOR... CHAINCASE... CONSOLE...
More information400 2x4/4x4 EFT SHARE OUR PASSION ṬM
SHARE OUR PASSION ṬM 400 2x4/4x4 EFT Model Number A2009IDG2BETR (Red - 2x4) Model Number A2009IDG2BETZ (Cat Green - 2x4) Model Number A2009IDG4BETR (Red - 4x4) Model Number A2009IDG4BETG (Green - 4x4)
More information1) Remove side panels. Remove clutch cover. Remove windshield by pulling up on the three posts secured into
UNDER HOOD HEAT ELIMINATOR A.K.A. THE BLOW HOLE by Mountain Tek Application 2013 Model Year SKIDOO XM Kit Contents 1) (1) Fan Tube Assembly 2) (1) Accessory Connect Harness 3) (1) Fan Vent Cover Plate
More information2018 Junior Sprint Rules
2018 KidSprint Engine Rules Briggs World Formula 2018B All parts must be Briggs & Stratton factory production parts unless otherwise noted in these rules. No machining, polishing or alteration of any parts
More information18SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines
8SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines KIT DESCRIPTION These service kits include all necessary parts to replace the low pressure fuel lines between the fuel filter housing and fuel
More informationIllustrated Parts List
FORM MS 54 08/11/2004 REPLACES FORM MS 54 11/14/2002 FILE IN SECT. 2 OF SERVICE MANUAL 311700 Illustrated Parts List Model Series 311700 TYPE NUMBERS 0005 through 0209. TABLE OF CONTENTS Air Cleaner.........................
More informationIllustrated Parts List
FORM MS 0670 3C 8/2001 REPLACES FORM MS 0670 2Q 11/2000 FILE IN SECT. 2 OF SERVICE MANUAL Illustrated Parts List Model Series TYPE NUMBERS 0042 through 1256. For Use On Engines Built Before Date Code 01070100.
More informationATV I l. l u. r a. Parts Manual ARCTIC CAT. 250 cc/300 cc
2000 I l l u st ATV 250 cc/300 cc Model No. A2000ATE2AUSG (250 - Green) Model No. A2000ATE2AUSR (250 - Red) Model No. A2000ATF2AUSG (300 2x4 - Green) Model No. A2000ATF2AUSR (300 2x4 - Red) Model No. A2000ATF4AUSG
More informationATV 50 Y-6 YOUTH CAT GREEN (A2004ATA2BUSZ) Page 1 of 50 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY
2004 ATV 50 Y-6 YOUTH CAT GREEN (A2004ATA2BUSZ) Page 1 of 50 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY 2004 ATV 50 Y-6 YOUTH CAT GREEN (A2004ATA2BUSZ) Page 2 of 50 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY
More informationENGINE COMPONENTS AND TESTING (CONT'D) Checking Nozzle Injection Pressure. Fuel Injector Removal And Installation (Cont'd)
Fuel Injector Removal And Installation (Cont'd) Figure 70-70-9 Checking Nozzle Injection Pressure OEM064 - Injector Nozzle Tester Figure 70-70- P-5797 Remove the injector nozzle holder bolt (Item ) [Figure
More informationSPORTFIRE SNOWMOBILE
A2 M25500 1980 MODEL (SERIAL NO. 120001-155000) 1981 MODEL (SERIAL NO. 155001-190000) 1982 MODEL (SERIAL NO. 190001-222000) 1983 MODEL (SERIAL NO. 222001-285000) 1984 MODEL (SERIAL NO. 285001- ) (SPECIFICATIONS
More informationENGINE CHAIN SAW Model CS 40EA
LIST E079 ENGINE CHAIN SAW Model 2010 8 18 (E1) 37 4 1 2 3 8 9 20 21 22 23 24 31 32 39 B 40 41 42 7 5 18 19 25 33 6 10 11 12 13 14 15 16 17 43 26 27 28 29 34 35 53 54 55 A 59 60 61 62 63 12 44 10 45 30
More informationPage 1 of HP B&S Vanguard Engine
1405 Page 1 of 41 14 HP B&S Vanguard Engine 1405 Page 2 of 41 14 HP B&S Vanguard Engine Ref # Part Number Qty S/P/F Description BS-28Q777-0647-E1 1 14 HP B&S Vanguard Engine 1 BS-496412 1 Cylinder Assembly
More informationLocal Option 206 Rules Manual Section 1 General Rules 1. Only stock Briggs & Stratton LO206 # engine will be allowed in this class.
Local Option 206 Rules Manual Section 1 General Rules 1. Only stock Briggs & Stratton LO206 # 124332-8201engine will be allowed in this class. o All parts will be stock unaltered Briggs & Stratton Animal
More information90 Y-12 Youth. Model Number A2005H4B2BUSR (Red) Model Number A2005H4B2BUSZ (Cat Green) Illustrated Parts Manual
90 Y-12 Youth Model Number A2005H4B2BUSR (Red) Model Number A2005H4B2BUSZ (Cat Green) Illustrated Parts Manual 2005 TABLE OF CONTENTS 2005 ATV 90 Y-12 Youth Red (Model No. A2005H4B2BUSR) Cat Green (Model
More informationREF. NO. DESCRIPTION TOP COWLING 2 MOLDING, AIR DUCT 3 RIVET 4 SEAL 5 HOLDER, CLAMP BAND 6 BOLT, WITH WASHER 7 HOOK
SUZHOU ALLPASS MACHINERY CO.,LTD Add:No.85,Jishui Road,Jinfeng Industrial Park,Mudu Town,Suzhou 215102,Jiangsu,P.R.China T15 SPARE PARTS EXPLODED DRAWING FIG. 1 1 TOP COWLING TOP COWLING 2 MOLDING, AIR
More informationINSTALLATION HYPERCHARGER AIR FILTER KIT 9754
9754 PARTS INCLUDED 1 Chrome Hypercharger Assembly 1 Support Bracket 1 Breather Hardware Kit, including: 2 1-1/4 Breather Bolts 2 Breather Hoses 4 Shim Washers 1 Twin Cam Breather Kit, Including: 1 Breather
More informationRemove Air Cleaner Cover and. Filter
Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove
More informationG561AV/G561AVS G621AV/G621AVS
2622-93121 CHAIN SAWS G561AV/G561AVS G621AV/G621AVS APPLICABLE SERIAL NUMBERS: AUGUST 1997 G561AV / G561AVS 714103 and up G621AV / G621AVS 719739 and up Fig.1 1 Fig.2 2 Fig.1 Part Number Q'ty Key No. Description
More information9/8/ MSHZ 2001 / TOP COWLING Yamaha Motor Corporation, U.S.A. All rights reserved.
9.9MSHZ 00 Page of 47 9/8/04 9.9MSHZ 00 / TOP COWLING 04 Yamaha Motor Corporation, U.S.A. All rights reserved. 9.9MSHZ 00 Page of 47 9/8/04 Part List 9.9MSHZ 00 / TOP COWLING REF - NO PART NUMBER PART
More informationSilverPro Series. Lawnmower. Parts Catalog. Form Number Model No and up.
Form Number 3350-622 SilverPro Series Lawnmower Model No. 10323-240000001 and up. Parts Catalog Ordering Replacement Parts To order replacement parts, please supply the part number, the quantity, and the
More informationElectronic Jet Kit Instructions
Rev 1.0.3 8027ST-TFI Patent Numbers: 7,000,599, 7,124,742 Electronic Jet Kit Instructions Thank you for choosing the Dobeck Performance Electronic Jet Kit for you re Arctic Cat F/M1000 Snowmobile. Dobeck
More informationCode 0 Description Pic Link # Used Diameter Thread Pitch Length Washer 1 Washer2 Nut size Class Notes F Alternator bracket mounting bolts
Code 0 Description Pic Link # Used Diameter Thread Pitch Length Washer 1 Washer2 Nut size Class Notes 1 15 1 2F Alternator bracket mounting bolts (Engine Lift Hook) 3 10 1.25 30 split washer flat 4 14mm
More informationSHELBY GT500
2007-2009 SHELBY GT500 Removal of Factory Unit WARNING: 1. Radiator fluid must be handled properly. Please observe local ordinances with regards to handling and disposal. 2. Allow vehicle and components
More information120 XC SP Model #S03WB1AS Rev. 01. E 2002 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /03
0 XC SP Model #S0WBAS Rev. 0 E 00 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /0 This page left blank intentionally. B BLOWER HOUSING... B C CARBURETOR... B CLUTCH... A CONSOLE... A CONTROLS...
More information120 XC SP Model #S01WB1AS Rev. 01. E 2000 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /00
0 XC SP Model #S0WBAS Rev. 0 E 000 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN 0/00 C CARBURETOR... B CLUTCH... A CRANKCASE... B D DECALS... A DRIVE TRAIN... A E ELECTRIC DEVICE... B ELECTRICAL
More informationINSTALLATION HYPERCHARGER AIR FILTER KIT 9992
9992 PARTS INCLUDED 1 Chrome Hypercharger Assembly with Chrome Blood Groove Trap Door and Chrome Butterflies 1 Support Bracket 1 Breather Hardware Kit, including: 2 1-1/4 Breather Bolts 2 Breather Hoses
More informationDodge Cummins Positive Air Shutoff
1 INSTALL MANUAL 2010-2012 6.7 Dodge Cummins Positive Air Shutoff P/N# 1036722 P/N# 1036722-M UPLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION An Information decal has been provided in this kit. This
More informationRCA PLUG KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RCA PLUG KIT P/N 2883824 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationRacing Performance Catalog & Reference Guide Model/Type:
Version 4/08 Racing Performance Catalog & Reference Guide Model/Type: 124435 8105-01 Table of Contents SAFETY... 1 WORLD FORMULA General Specs...3 Special Tools...3 Torque Specs...3 Racing Specifics...3
More informationX4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY
2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY 2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 2 of 80 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3570-001 1 /P Intake,
More information400 4x4 Euro MODEL NUMBER A2008IDG4BEUR (RED) MODEL NUMBER A2008IDG4BEUG (GREEN) MODEL NUMBER A2008IDG4BEUZ (CAT GREEN) MORE TO GO ON.
2008 400 4x4 Euro Illustrated Parts Manual MODEL NUMBER A2008IDG4BEUR (RED) MODEL NUMBER A2008IDG4BEUG (GREEN) MODEL NUMBER A2008IDG4BEUZ (CAT GREEN) MORE TO GO ON. TM TABLE OF CONTENTS 2008 ATV 400 4x4
More informationPOLARIS CLUTCH HELIX'S
Clutch -9 POLARIS CLUTCH HELIX'S DALTON HELIX - New PR Models $119.95-F PR radiused models are built like the factory "R" series that comes on many Polaris models. PR 45/36 PR 47/39 PR 48/38-32 PR 50/36
More informationWIDETRAK LX Model #S03SU4BS Rev. 01. E 2002 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /03
WIDETRAK LX Model #S0SUBS Rev. 0 E 00 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /0 TABLE OF CONTENTS WIDETRAK LX S0SUBS Parts Manual AIR BOX A... B C BATTERY BOX... B BRAKE... B CARBURETOR...
More informationNot for Reproduction ADVANCE PRODUCT SERVICE INFORMATION APSI NO: 101 DATE: AUGUST SERIES UTILITY ENGINE 130G00 OHV HORIZONTAL SHAFT
ADVANCE PRODUCT SERVICE INFORMATION APSI NO: 101 DATE: AUGUST 2014 SUBJECT: MODELS: 950 SERIES UTILITY ENGINE 130G00 OHV HORIZONTAL SHAFT This APSI provides basic servicing information in advance of the
More informationWEBER CARBURETOR TROUBLESHOOTING GUIDE
This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful
More information2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit INSTALLATION GUIDE FOR RACING USE ONLY
INSTALLATION GUIDE 2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit FOR RACING USE ONLY Congratulations on your purchase of the AWE Tuning S-FLO Intake for the 2010+ Audi B8 S4 and B8 S5 3.0T. Exquisite build
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: C
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-721C 2011-2013 MINI Cooper S L4-1.6L SEE NOTE* 2011-2013 MINI Clubman S L4-1.6L SEE NOTE* 2011-2013 MINI Cooper
More information17-44HXLE Lawn Tractor
Form Number 3350-107 17-44HXLE Lawn Tractor Model No. 71283-240000001 and up. Parts Catalog Ordering Replacement Parts To order replacement parts, please supply: the part number, the quantity, and the
More informationReproduction. Not for. Briggsracing.com. CORPORATION Briggs & Stratton Corporation MS /08
Briggsracing.com MS-5702-4/08 BRIGGS&STRATTON CORPORATION Post office box 702 Milwaukee, WI 53201 USA 414 259 5333 2008 Briggs & Stratton Corporation Version 4/08 Racing Performance Catalog & Reference
More information