NME1254 and FME1504 SERVICE PARTS

Transcription

1 This parts list contains the part numbers and descriptions of the service parts for the NME1 and FME10 air and water cooled. The water cooled condenser changed between the A and B series. Be sure to check the complete model number before selecting the condenser part number. Table of Contents PANELS AIR COOLED REFRIGERATION WATER COOLED REFRIGERATION NME EVAPORATOR FME EVAPORATOR CONTROL BOX GEARMOTOR RESERVOIR, DRAINS, ICE CHUTE, ICE LEVEL SENSORS WIRING DIAGRAMS June 00 Page 1

2 PANELS A1-00 Top Panel Stainless. A-00 Service Panel for S.S.. A-001 Filter (air cooled only). A1-00 Right End Panel S.S.. A10-00 Front Panel S.S Emblem Clip For Emblem (). A-001 Base Assembly Screw. 0-- Washer. A1-00 Left End Panel S.S. 1. A0-00 Back panel Screw 1. A-01 Retainer July 01 Page

3 AIR COOLED REFRIGERATION 1, a b Alt. Access Valve Air Cooled Conden.. A1-001 Shroud Bolt Washer Expansion Valve Access valve a Stem cap b Core cap Hi Pressure Control /0/1 Comp. w/drier This compressor has an internal overload Grommet Sleeve Washer Bolt Drier L. P. Control Fan Motor 0--0 Screws, motor to bracket Screw Washer Fan Motor Bracket Fan Blade 1. A1-00 Insulation for TXV Access valve body Core Cap April 00 Page

4 WATER COOLED REFRIGERATION Alt. Access Valve 1 b a Expansion Valve Access valve a Core cap b Stem cap. 1-- Compressor 0-0/0/1 Includes drier, Overload is internal Grommet Sleeve Washer Bolt. A1-00 Drain Drier Lo Press. Control Water Reg. Valve Elbow Hi Pressure Control A series WC Condenser 1--1 B series WC condenser Screw Washer Insulation for TXV Access valve body Core Cap February 01 Page

5 NME EVAPORATOR A00-00 Breaker Includes Items 1 & Soc. head Screw O-ring. A01-0 Auger Water Seal. A-001 Ring, Water Seal. A0-00 Evaporator Hex Cap Screw. A-001 Bail clamp Note: Evaporator is not available assembled with internal parts Ice Chute Cover Ice Chute Body w/ins Drain hose clip O-ring Ice Sweep Breaker Cover Auger Stud Lip Seal Cap screw 1. A-00 Bearing Lip Seal O-Ring Water Shed Insulation donut March 00 Page

6 FME EVAPORATOR A0-00 Breaker Includes Items 1 & Soc. head Screw O-ring. A01-0 Auger Water Seal. A-001 Ring, Water Seal. A0-00 Evaporator Hex Cap Screw. A-001 Bail clamp Ice Chute Cover Ice Chute Body w/ins. Note: Evaporator is not available assembled with internal parts Drain hose clip O-ring Ice Sweep Breaker Cover Auger Stud Lip Seal Cap screw 1. A-00 Bearing Lip Seal O-Ring Water Shed Slotted collar O-ring Insulation donut March 00 Page

7 CONTROL BOX 1, Start Capacitor Run Capacitor. A1-00 Start Cap. Bracket Relay Screw. A-001 Run Cap. Bracket Phase Contactor Mode Switch. 1-- Circuit Board Stand off. No Number Control Box 1. A-001 Cont. Box Cover Not shown: Low voltage harness, pin High voltage harness, pin February 00 Page

8 GEARMOTOR 1 *NOTE: GEARCASE COVER INCLUDES COVER, OUTPUT SHAFT, KEY, OUTPUT GEAR, BEARINGS, AND SEAL Start Switch, Emerson 1-0- Start switch, GE split phase* Drive Motor 0-0 v Water Shed Bearing, Emerson 1-0- Bearing, GE split phase. A-0 Bolt. A-0 First Gear & Bearing. A-0 nd Gear & Bearing. A-01 Gasket. A-00 Gear Case A-0 Oil, 1 Container. A-0 Gearcase Cover* 1. A0-0 Complete Gearmotor Assembly. 0-0 v. A0-00 Gearcase kit. No motor. OIL GE same as Marathon* October 0 Page Note: An output shaft seal is available, the part number is A-0. However, if water has entered the gearbox thru the seal, replace the gearcase cover, not just the seal.

9 RESERVOIR, DRAINS, ICE CHUTE, ICE LEVEL SENSORS b a , Ice Chute Lower. A-00 Insulation collar top* a A-001 Insulation collar, top*. A-001 Insulation Collar Inside*. A0-01 Ice level sensor set. A0-001 Chute Gasket Drip Pan Insulation Collar. same as item, use one per unit. A1-00 Strap kit Drain hose Inlet tube, ft req. 1. A1-00 Preformed Hose Plug Water inlet fitting Male connector August 0 Page Drain fitting 1. A-01 Reservoir bracket Drip pan gasket Hose clamp Pal Nut 1. A1-00 Drain - Water Cooled Water level sensor Float & Reservoir complete a 0--0 Float valve b 0--0 Plunger * items, a and no longer used after Oct Insulation part of ice chute body & donut. See pages and.

10 AIR AND WATER COOLED, 0-0/0/1 January 000 Page

11 AIR AND WATER COOLED, 0-0/0/1 January 000 Page

12 Bulletin Number: PS-1- Bulletin Date: September 1 SERVICE BULLETIN Subject: NME, FME, NSE, NDE and TDE0/0 Top Bearing Lubrication Two parts have been made available as helpful aids to use when lubricating the top bearing is a needle that snaps onto a standard grease gun fitting. Use it to insert and deeply pack the proper lubricant into the top bearing.. A0-001 is a tube of the proper lubricant, also designed to fit a standard grease gun. Both numbers are in the parts price list. Needle, shown inserted into bearing