Typical Feed Water Heater Isolation System.

Size: px
Start display at page:

Download "Typical Feed Water Heater Isolation System."

Transcription

1 Type AVS 4/5 Typical Feed Water Heater Isolation System. Features and Benefits These valves are designed to bypass high pressure feedwater around a group of heaters in the event of high water level in the shell caused by a defective tube, weld or drain system. The time available to give protection to a turbine in modern feed systems is short but these valves can operate in approximately 5 seconds in a 300mm bore pipe system with the minimum of hydraulic shock. Protection is achieved in the system by installing fast closing tee and changeover valves in the pipework around a heater or group of heaters. These valves are equally applicable in new or established stations. The motive power employed is the feedwater pressure and the system is designed to 'fail safe' in that the heaters will be by-passed if either electric or pneumatic supplies fail. Technical data Sizes : DN 80 - DN 500 Construction : DIN 3840 Pressure Class : PN PN 500 Tyco reserves the right to change the contents without notice SEMDR-0008-EN-0202

2 Type AVS 4/5 Operation In case of damage happening to the preheater pipes, the feedwater supply upstream of the pump and the feed-water backflow from the boiler to the preheater must be shut off in the shortest possible time. Quick shut off and deviation of the flow will both prevent the preheater steam jacket designed for low pressures from being endangered, and also maintain the feed-water supply to the boiler. Moreover, the turbine is protected against water breaking in by flow backs through the bleeder pipe. Due to the automatic shut off of the preheater and the simultaneous opening of the by-pass line, the feed-water keeps on flowing steadily. Even excessive pipe lenghts between the pump and the AV5 valve will not create any additional dynamic forces. Due to the deviation of flow, the water column contained in the by-pass will have to be accelerated. Short by-pass pipes will keep such acceleration forces on a low level. The AV quick closing valves are controlled by their own medium and will respond within a second's time, without varying operating forces and almost free of friction, because the valve seating faces close axially and do not slide on each other, as e.g. with gate valves. If the feed-water pressure within the preheater pipes rises due to faulty control or during trial runs, the AV valves will act as safety valves and open slightly. In normal operation pump pressure will prevail in the inlet of the AV5 changeover valve. Due to pressure losses, the pressure in the by-pass line is somewhat lower. This pressure differential as well as the balanced stem that is passed to the outside, will safely hold the disc of the AV valve in open position, providing a shut off towards the by-pass. Minor pressure fluctuations within the range of 5% of the inlet pressure will not affect the operation of the AV valves. Higher pressure variations will have to be checked and may require a change in design. In case of damage in the preheater, the level control emits an electric impulse to the solenoid control valve, in addition to possible optical and audible warnings. The valve opens and relieves the cylinders "A" of the AV valves. Cylinders "B" receive the full pressure of the feed-water line via a small passage, which causes the discs to move into their closing positions. The preheater is no longer in operation and the feed-water flow passes through the by-pass line. When the solenoid control valves closes, the AV5 changeover valve will only remain in its closed position, if the feed-water pressure in the preheater has lowered by at least 10% as compared with the pump pressure and does not rise again. Therefore, with power test runs, the AV valves will open automatically, and the preheater is put into operation again, as soon as the solenoid control valve is closed. This automatic opening is effected by the valve stems being balanced and passed through to the outside. The pistons of the AV valves have been so dimensioned, that any opening towards the preheater is prevented, if the latter is pressureless or under low pressure. This design prevents any sudden and harmful admission of pressure to the preheater piping. For the start-up or after repairs the preheater is filled via the refill pipe by the pump line. Only then the AV valves can be opened, or will open automatically after the pressure has been balanced within the system. With low operating pressures, the open hand-operated control valve relieves the cylinder "B" sufficiently for allowing the disc to move into its open position. + + Balance pipe Special No. 372 A2 valve interlocking + Outlet to Boiler * = are no part of our delivery programme Quick closing change over valve Inlet from pump Reversing valve VA 500 Refill pipe Refill valve A B B A Preheater Balance valve Special No. 372 A2 valve interlocking AVS5 + Special No. 37 Position Indicator open Special No. 36 Position Indicator closed * Control pipe Bypass line * Level control Special No. 36 Position Indicator closed Special No. 37 Position Indicator open AVS4 Quick closing check valve Time delay relais of appr. 30 sec. c1 * Stop valve VA 500 Special No. 371 A4 valve interlocking (open blocked) c2 * Solenoid control valve EMS- Time delay relais of appr. 30 sec. Closing the solenoid control valve after changeover is necessary, because a permanent relief via the control pipe may cause erosion. As shown in the drawing, a corresponding closing impulse is emitted by the electric indicator (SN 36) in "closed" position. Contactors C1 and C2 are lagging at approx. 30 seconds. Design Quick - Closing Check Valves Check Valves AVS4. AVF4 Three way valves AVS5. AVF5 Size of seat Maximum Flow Quantity Type Cast steel DIN - PN DIN- DIN-PN PN25-40 Forged Steel DIN - PN Control Pipes DIN-DN 15 DIN-DN 25 t/h Control Valves For AV Valves Close EMS1 to EMS4 Solenoid Control Valves Other control valves on request Open Automatically VKS11-Stop Valve Min.(bar) type Forged Steel Cast Steel Forged Steel Cast Steel Equipment Type ST.KG Spur Gear and bevel Gear Type FA Remote driving parts E-Actuators Size and connect. acc. to ISO 5210 Quick - Closing Check Valves For easy mounting of the AV valves, they should preferably be installed in vertical position. Their pressure losses are equivalent to 90 bands and are substantially more advantageous as compared with T-fittings. In case of preheater groups, the valve bodies being designed as fittings, may serve for the feed-water line to be distributed to the individual preheaters. Our technical datasheets will inform you on the possible number of connections, their relative positions and sizes. Control Valves The feed-water pressure being used as the source of energy for operating the AV valves necessitates minimum overpressures in the preheater system as shown in the adjoining column. Where valves are to be activated by solenoid control valves at lower pressures, the AV valves will have to be modified according to individual requirements. Equipment The blocking stem enables the AV valves to be closed independently from the solenoid control. The blocking stems must not be used for closing the disc against the full operating pressure. The AV4 non return valve must not be closed before the AV5 changeover valve has been blocked. The blocking stem can be operated by handwheel or by remote drives as per margin. For the maintenance of the solenoid control valve during operation, the stop valve can be closed after the preheater protection has been changed over to bypass operation and the blocking stems have been actuated. This procedure is guaranteed by the valve interlockings SN 322 and SN 341 provided. Tyco reserves the right to change the contents without notice page 2

3 Quick closing check valve - Type AVS 4 PN : cast steel PN : forged steel / / / / / / Class PN (100) (160) (250) (320) Trim Body Disc Piston seat surface seat surface rod No Part No 1 Part No 4 Part No % Cr 17% Cr 13% Cr Tyco reserves the right to change the contents without notice page 3

4 Quick closing check valve - Type AVS 4 Parts list Part Part name Material Code 01 A A182F body A A182F middle part of the body A A182F inlet connecting pipe A A182F outlet connecting pipe A A182F hardfacing Chromium steel Chromium steel Chromium steel Chromium steel Chromium steel Chromium steel 1.7 welding seam 1.8 welding seam 2 cover A A182F cylinder / / / / / / part. Cr-plated part. Cr-plated part. Cr-plated part. Cr-plated part. Cr-plated part. Cr-plated 4 disc A A182F hardfacing Chromium steel Chromium steel Chromium steel Chromium steel 5 rod with piston / / / / par. Cr-plated par. Cr-plated par. Cr-plated par. Cr-plated 8 disc stem connection split ring ring tightening plate split ring convex seal flange control stud bolt hexagonal nut piston ring segment ring A182F A182F ring A A182F cover seal Graphit/ Graphit/ Graphit/ Graphit/ base ring packing Graphit Graphit Graphit Graphit 29 gland shaft gland flange stud washer Ferrite Ferrite Ferrite Ferrite 34 hexagonal nut stud hexagonal nut allan bolt A4 A4 A4 A4 38 name plate roundheaded notched nail Austenite Austenite Austenite Austenite 41 bonnet Divers Divers Divers Divers 42 spindle indicator ring indicator ring guide bolt threaded bush ring bearing axial-needle bearing ball bearing steel ball bearing steel ball bearing steel ball bearing steel 49 threaded pin Ferrite Ferrite Ferrite Ferrite 50 pipe nut Ferrite Ferrite Ferrite Ferrite 51 fitting key hand wheel lubrication nipple Ferrite Ferrite Ferrite Ferrite 55 tightening pin Springsteel Springsteel Springsteel Springsteel 58 bonnet holder Divers Divers Divers Divers 59 limit switch Divers Divers Divers Divers 59.1 allan bolt Tyco reserves the right to change the contents without notice page 4

5 Quick closing check valve - Type AVS 4 Welding Ends PN Size of Seat diameter DN Inlet DN Outlet Bypass Dimensions in mm Weight seat mm mm mm mm S H1 H2 H3 h D a c kg 160/ / Welding ends as specified by customer Tyco reserves the right to change the contents without notice page 5

6 Quick closing three-way valve - Type AVS 5 PN : cast steel PN : forged steel / / / / / /36 56/ zum Steuerventil to control valve zum Handventil to stop valve Class PN (100) (160) (250) (320) zum Handventil to stop valve zum Steuerventil to control valve Trim Body Disc Piston seat surface seat surface rod No Part No 1 Part No 4 Part No % Cr 17% Cr 13% Cr Tyco reserves the right to change the contents without notice page 6

7 Quick closing three-way valve - Type AVS 5 Parts list Part Part name Material Code 01 A A182F body A A182F middle part of the body A A182F inlet connecting pipe A A182F outlet connecting pipe A A182F bypass connecting pipe A A182F hardfacing Chromium steel Chromium steel Chromium steel Chromium steel Chromium steel Chromium steel 1.6 hardfacing Chromium steel Chromium steel Chromium steel Chromium steel Chromium steel Chromium steel 1.7 welding seam 1.8 welding seam 1.9 welding seam 2 cover A A182F indication plate indication plate cylinder / / / / / / part. Cr-plated part. Cr-plated part. Cr-plated part. Cr-plated part. Cr-plated part. Cr-plated 4 disc A A182F hardfacing Chromium steel Chromium steel Chromium steel Chromium steel 4.2 hardfacing Chromium steel Chromium steel Chromium steel Chromium steel 5 rod with piston / / / / par. Cr-plated par. Cr-plated par. Cr-plated par. Cr-plated 8 disc stem connection split ring ring tightening plate split ring convex seal flange control stud bolt hexagonal nut piston ring piston ring segment ring A182F A182F ring A A182F cover seal Graphit/ Graphit/ Graphit/ Graphit/ Graphit/ base ring packing Graphit Graphit Graphit Graphit 29 gland shaft gland flange stud washer Ferrite Ferrite Ferrite Ferrite 34 hexagonal nut stud hexagonal nut allan bolt A4 A4 A4 A4 38 name plate roundheaded notched nail Austenite Austenite Austenite Austenite 41 bonnet Divers Divers Divers Divers 42 spindle indicator ring indicator ring guide bolt threaded bush ring bearing axial-needle bearing ball bearing steel ball bearing steel ball bearing steel ball bearing steel 49 threaded pin Ferrite Ferrite Ferrite Ferrite 50 pipe nut Ferrite Ferrite Ferrite Ferrite 51 fitting key hand wheel lubrication nipple Ferrite Ferrite Ferrite Ferrite 55 tightening pin Springsteel Springsteel Springsteel Springsteel 56 stud hexagonal nut bonnet holder Divers Divers Divers Divers 59 limit switch Divers Divers Divers Divers 59.1 allan bolt manual control valve Divers Divers Divers Divers Tyco reserves the right to change the contents without notice page 7

8 Quick closing three-way valve - Type AVS 5 Welding Ends PN Size of Seat diameter DN Inlet DN Outlet Bypass Dimensions in mm Weight seat mm mm mm mm S H1 H2 H3 h D a c kg 160/ / Welding ends as specified by customer Tyco reserves the right to change the contents without notice page 8

9 Quick closing three-way valve - Type AVS Parts list 1 Pickling cylinder 2.1 Pickling disc 2.2 Pickling stem 2.3 Tightening screw 2.4 Sealing plate 2.5 Holding plate 2.6 Allan bolt 3 Guide ring 4 Guide bolt 5 Dummy convex seal 6 Packing 8 Allan bolt 9 Gasket AVS Example for designation of check valves Standard accessories Material Specification Size of extra connections Outlet nominal size Inlet Nominal Size Nominal Pressure Seat size Type of Valve, abbr. Locations of connections for seat sizes The maximum number of connections of the outlet plane is 4 of limited size. There must be at least 90 between adjacent connections. Their number, sizes and angular positions must be stated upon ordering or inquiring. The angular positions of the control connection (16) is independent of the connections of the valve body. It can be fixed in any desired position after loosening the hexagonal nuts (36, 57, 58.2). Where an extra manual control valve SN 66 is employed, it should be fitted exactly opposite (180 ) to the control connection (16). Tyco reserves the right to change the contents without notice page 9

10 Quick closing three-way valve - Type AVS Parts list Pickling cylinder 2.1 Pickling disc 2.2 Pickling stem 2.3 Tightening screw 2.4 Holding plate 2.5 Allan bolt 2.6 Allan bolt 3 Guide ring 4 Guide bolt 5 Dummy convex seal 6 Packing 7 O-Ring 8 Allan bolt 9 Gasket AVS Example for designation of three-way-valves Standard accessories Material Specification Size of extra connections Bypass nominal size Outlet nominal size Inlet Nominal Size Nominal Pressure Seat size Type of Valve, abbr. Locations of connections for seat sizes Maximum number of connections of the inlet and bypass plane is 4 of limited size. There must be at least 90 between adjacent connections. Their number, sizes and angular positions must be stated upon ordering or inquiring. Normally the control connection (16) is positioned above the inlet connection (1.2) and the manual control valve (61) is placed at 180 C to the control connection. It can, however, be fixed in any position after loosening the hexagonal nuts (36, 57, 58.2), provided the position of connection and valve remains unchanged with reference to their opposite position of 180. Tyco reserves the right to change the contents without notice page 10

11 Solenoid control valve - Type EMS 3-4 and EMF 3-4 Parts list ASV4 1 Lid 2 Tightening screw 3 Threaded stem 4 Hexagonal nut 5 Tightening plate 6 Shutt off plate 7 O-Ring 8 O-Ring 9 O-Ring 10 Ring screw 11 Safety ring 12 Cylinder slotted pin AVS4 Parts list ASV5 1 Lid 2 Tightening screw 3 Threaded stem 4 Hexagonal nut 5 Tightening plate 6 Shutt off plate 7 O-Ring 8 O-Ring 9 O-Ring 10 Ring screw 11 Safety ring 12 Cylinder slotted pin AVS5 Tyco reserves the right to change the contents without notice page 11

12 Quick closing check valve - Type AVS 4 Standard Accessories Manual Control Valve (SN 66). Tyco reserves the right to change the contents without notice page 12

13 Quick closing three-way valve - Type AVS 5 Standard Accessories Hydraulic brake to increase opening and closing times by several seconds (SN 74). Detail Z Z Detail Y Y Tyco reserves the right to change the contents without notice page 13

14 Type AVS 4/5 E M S Example for Solenoid Control Valve Specification Standard accessories Materials Specification Inlet Nominal Size Control Principle Outlet Connection Solenoid Control Angle Type Body Installation Solenoid Control Valves are designed to quickly and reliably believe and load the control chambers of valves controlled by their own medium. They are employed for activating preheater safety devices, quick-closing and opening valves as well as controlled safety relief valves. Their inlet is either directly connected to the standard connections of the controls or through the intermediary of control pipes. Existing safety regulations should be adhered to. Maximum nominal pressures must not be exceeded, and control pipes should not be smaller in diameter than the connections of the control valves. Suitable controlling instruments may be connected to the respective bores. Design Materials are specified for all parts exposed to pressure, for those giving tight seal to atmosphere and for spares. Inlet connection (3) is also available in different materials if local operating conditions should render it necessary. Other material specifications on request. All major internal parts are made from high-alloyed, wear resistant materials with guaranteed physical properties and coefficients of expansion. In case of damage, e.g. by foreign matter or where parts are worn after continuous heavy service, exchange of such parts is recommended by making use of our ex store spare kits. Please state rating plate particulars when ordering or inquiring. Operation EMS3. EMF3 De-energized, Solenoid Valve Open, indirect operation With Solenoid (57) de-energized, disc (29) is pushed into " open "position against the service pressure by the biased cup springs via stem (40). The upper side of the check disc (25) becomes pressureless and moves upward into "open "position. Upon the current being switched on, solenoid (57) will return to its initial position against the force of the cup springs. Spring (30) assisted by the service pressure causes disc (29) to close smartly onto its seat. This closing action is also assisted by the service pressure generating above check disc (25). EMS4.EMSF4 Energized, Solenoid Valve Open, indirect operation With Solenoid (57) energized, disc (29) is pushed into" open" position against the service pressure by magnetic force via stem (40). The upper side of the check disc (25) becomes pressureless and moves upward into "open" position. Upon the current being switched off, pressure spring pulls solenoid (57) back to its initial position. Spring (30) with the aid of the service pressure pushes disc (29) into closed position. This closing action is also assisted by the service pressure generating above disc (25). Table??? Tyco reserves the right to change the contents without notice page 14

PREHEATER BYPASS SYSTEMS

PREHEATER BYPASS SYSTEMS PREHEATER BYPASS SYSTEMS PREHEATER BYPASS SYSTEMS OVERVIEW 2014 GS FEED WATER HEATER BYPASS SYSTEM General Description These valves are designed to bypass high pressure feed water around the pre-heaters

More information

Sempell controlled non-return or Bled Steam Check Valves prevent unallowable pressure built up in the turbine coming due to back-flowing steam.

Sempell controlled non-return or Bled Steam Check Valves prevent unallowable pressure built up in the turbine coming due to back-flowing steam. Sempell controlled non-return or Bled Steam Check Valves prevent unallowable pressure built up in the turbine coming due to back-flowing steam. Features and Benefits Special advantages of the valve series

More information

Specially designed low-maintenance control valves for a wide range of applications in water circulation

Specially designed low-maintenance control valves for a wide range of applications in water circulation SEMPELL Specially designed low-maintenance control valves for a wide range of applications in water circulation Features and benefits modular design the valve is suitable for continuous operation good

More information

Sempell High Pressure Stop Valves Model VA510 (DIN)

Sempell High Pressure Stop Valves Model VA510 (DIN) Designed for highest pressure and temperature applications using high alloy or stainless steels. Features T-pattern globe type Body made of forged steel Wear resistant stellite body seat Conical seat with

More information

Gate valves Gate valve 700 HJ/JJ (GA PN 10-40) PN DN

Gate valves Gate valve 700 HJ/JJ (GA PN 10-40) PN DN Gate valves Gate valve 700 HJ/JJ (GA PN 10-40) PN 10-100 DN 50-150 Admissible operating pressure [bar] at design temperature [ C] Material PN -60-10 20 100 150 200 250 300 350 400 410 420 430 440 450 460

More information

Sempell High Pressure Stop Valves Model VA500 (ASME)

Sempell High Pressure Stop Valves Model VA500 (ASME) 7 Sempell High Pressure Stop Valves Designed for the isolation and control of high temperature and high pressure systems, this multipurpose globe valve can be used in a wide variety of applications. Features

More information

SEMPELL. All applications of stop valves up to a Nominal Diameter of 50 mm. VA 500 Serie high-pressure Stop Valves DIN

SEMPELL. All applications of stop valves up to a Nominal Diameter of 50 mm. VA 500 Serie high-pressure Stop Valves DIN DIN SEMPELL All applications of stop valves up to a Nominal Diameter of 50 mm. Features Bonnetless die-forged body. One piece body design with packing only. Stellited seat. Stem nut drive sealed against

More information

Sempell High Pressure Stop Valves Model VA500 (DIN)

Sempell High Pressure Stop Valves Model VA500 (DIN) Designed for the isolation and control of high temperature and high pressure systems, this multipurpose globe valve can be used in a wide variety of applications. Features Type tested (except for material

More information

Non-Return Valves - Type 801 ASME SEMPELL

Non-Return Valves - Type 801 ASME SEMPELL SEMPELL Sempell controlled and uncontrolled Non-Return or Swing Check Valves prevent unallowable pressure built up in the turbine coming due to back-flowing steam. Features and Benefits low maintenance

More information

Globe valves Shut-off check valve 200 AE/BE PN DN Globe valves Lift check valve 240 MT PN DN 10-50

Globe valves Shut-off check valve 200 AE/BE PN DN Globe valves Lift check valve 240 MT PN DN 10-50 Globe valves Shut-off check valve 200 AE/BE PN 10-160 DN 10-50 Globe valves Lift check valve 240 MT PN 10-160 DN 10-50 Admissible operating pressure [bar] at design temperature [ C] 1) Material PN -200-60

More information

H i g h P r e s s u r e V a l v e

H i g h P r e s s u r e V a l v e High Pressure Valve HIGH PRESSURE VALVES Applications & Specifications Range Gate Valve Advantages STRACK has designed and manufactured high pressure valves for over 35 years. Currently more than 3000

More information

VELAN TRUNNION-MOUNTED

VELAN TRUNNION-MOUNTED VELAN TRUNNION-MOUNTED Velan s standard trunnion-mounted ball valves offer increased value by incorporating advanced design features. TRUNNION-MOUNTED BALL The ball is fixed and the seat rings are floating,

More information

Main Steam Isolation Valves (MSIV) in Nuclear Power Plants with PWR

Main Steam Isolation Valves (MSIV) in Nuclear Power Plants with PWR Main Steam Isolation Valves (MSIV) in Nuclear Power Plants with PWR FD2 1 E 02/2000 1 Introduction As isolating valve in the main steam line of nuclear power stations different designs are known. Beside

More information

Gate valve, billet-forged. p approx. 600 bar DN Applications

Gate valve, billet-forged. p approx. 600 bar DN Applications Type series booklet 7451.1/11-10 ZTS Gate valve, billet-forged with pressure seal bonnet with butt weld ends p approx. 600 bar DN 50-800 Applications In industrial plants, power stations, process and marine

More information

VB VALVES & AUTOMATION

VB VALVES & AUTOMATION Introduction to Valve What are Valves? Valves are mechanical device that controls the flow and pressure within a system or process. They are essential components of a piping system that conveys liquids,

More information

Direct contact, metal-to-metal seating, make the gate valve ideal for most shut-off applications. Class 800 ANSI.

Direct contact, metal-to-metal seating, make the gate valve ideal for most shut-off applications. Class 800 ANSI. Direct contact, metal-to-metal seating, make the gate valve ideal for most shut-off applications. Class 800 ANSI. Features Two inch and smaller valves are available with threaded or socket weld ends as

More information

Series Direct contact, metal-to-metal seating, make the globe valve ideal for most shut-off applications. Features

Series Direct contact, metal-to-metal seating, make the globe valve ideal for most shut-off applications. Features Direct contact, metal-to-metal seating, make the globe valve ideal for most shut-off applications. Features General application Designed for ASME boiler and pressure vessel code, section I applications

More information

Direct contact, metal-to-metal seating, make the gate valve ideal for most shutoff applications. Class 800 ANSI.

Direct contact, metal-to-metal seating, make the gate valve ideal for most shutoff applications. Class 800 ANSI. Direct contact, metal-to-metal seating, make the gate valve ideal for most shutoff applications. Class 800 ANSI. Features Two inch and smaller valves are available with threaded or socket weld ends as

More information

AKG-A/AKGS-A. Type Series Booklet

AKG-A/AKGS-A. Type Series Booklet AKG-A/AKGS-A PN 63-160 DN 80/80-300/250 Pressure seal bonnet Flanged/Butt Weld Ends Type Series Booklet Legal information/copyright Type Series Booklet AKG-A/AKGS-A KSB Aktiengesellschaft Pegnitz All rights

More information

RELIABLE DURABLE SAFE Industrietechnik GmbH PERMADOR PARADOR K2000R HIGH-PRESSURE- GATE VALVES SWING CHECK VALVES PARADOR PERMADOR K2000R

RELIABLE DURABLE SAFE Industrietechnik GmbH PERMADOR PARADOR K2000R HIGH-PRESSURE- GATE VALVES SWING CHECK VALVES PARADOR PERMADOR K2000R RELIABLE DURABLE SAFE Industrietechnik GmbH PERMADOR PARADOR K2000R HIGH-PRESSURE- GATE VALVES SWING CHECK VALVES PARADOR PERMADOR K2000R INTRODUCTION TO THE COMPANY DRW INDUSTRIETECHNIK DRW INDUSTRIETECHNIK

More information

AKG-A/AKGS-A Type Series Booklet

AKG-A/AKGS-A Type Series Booklet Gate Valve AKG-A/AKGS-A PN 63-160 DN 80/80-300/250 Type Series Booklet Legal information/copyright Type Series Booklet AKG-A/AKGS-A All rights reserved. The contents provided herein must neither be distributed,

More information

Series Direct contact and metal-to-metal seating makes the T-pattern globe stop valve ideal for most shut-off applications.

Series Direct contact and metal-to-metal seating makes the T-pattern globe stop valve ideal for most shut-off applications. 7 YARWAY Hancock T-Pattern Globe valves Direct contact and metal-to-metal seating makes the T-pattern globe stop valve ideal for most shut-off applications Features Heavy integral stellite hardfacing on

More information

YARWAY HANCOCK Y-PATTERN FORGED STEEL GLOBE STOP VALVES SERIES 4000

YARWAY HANCOCK Y-PATTERN FORGED STEEL GLOBE STOP VALVES SERIES 4000 Direct contact and metal-to-metal seating make this Y-pattern globe stop valve ideal for most shut-off applications. FEATURES All valves feature integral Stellite hardfacing on both body and disc seating

More information

Operating Instructions ROCO Butterfly Valve with SKG Slider-crank Mechanism, with Electric Multi-turn Actuator

Operating Instructions ROCO Butterfly Valve with SKG Slider-crank Mechanism, with Electric Multi-turn Actuator Operating Instructions ROCO Butterfly Valve with SKG Slider-crank Mechanism, with Electric Multi-turn Actuator 1 Product and Performance Description 2 Design Features of ROCO Butterfly Valve 3 Installation

More information

78200/18200 Series LINCOLNLOG Valves Anti-cavitation High Pressure Control Valves

78200/18200 Series LINCOLNLOG Valves Anti-cavitation High Pressure Control Valves LINCOLNLOG Valves Anti-cavitation High Pressure Control Valves Featuring High Resistance Multiple Stage LINCOLNLOG Trim Angle Configuration 78200 Globe Configuration 18200 Specification Data CP6020 10/97

More information

AKG-A/AKGS-A. Type Series Booklet

AKG-A/AKGS-A. Type Series Booklet Gate Valve AKG-A/AKGS-A PN 63-160 DN 80/80-300/250 Type Series Booklet Legal information/copyright Type Series Booklet AKG-A/AKGS-A All rights reserved. The contents provided herein must neither be distributed,

More information

High-pressure shut-off globe valve V30 High-pressure shut-off globe valve with control cone V40 PN , DN , T max : 550 C

High-pressure shut-off globe valve V30 High-pressure shut-off globe valve with control cone V40 PN , DN , T max : 550 C High-pressure shut-off globe valve V30 High-pressure shut-off globe valve with control cone V40 PN 63-160, DN 50 150, T max : 550 C Shut-off globe valve (series V30) or shut-off globe valve with control

More information

Mounting and Operating Instructions EB 5868/5869 EN

Mounting and Operating Instructions EB 5868/5869 EN Electric Control Valves Types 3213/5857, 3213/5824, Types 3214/5824, 3214/3374, 3214/3274 with safety function: Types 3213/5825, 3214/5825, 3214/3374, 3214/3274 Pneumatic Control Valves Types 3213/2780-1,

More information

Slab & Double Expanding Gate Valves

Slab & Double Expanding Gate Valves Slab & Double Expanding Gate Valves Double Expanding Characteristics The main feature of a double expanding gate valve is the 2 pieces obturator that guarantees a simultaneous mechanical seal both in the

More information

Hopkinsons CONTENTS SCHEDULE OF SHELL BOILER MOUNTINGS. Hopkinsons. Safety Valves 5. Boiler Stop Valves 17. Feed Check Valves 18. Blowdown Valves 20

Hopkinsons CONTENTS SCHEDULE OF SHELL BOILER MOUNTINGS. Hopkinsons. Safety Valves 5. Boiler Stop Valves 17. Feed Check Valves 18. Blowdown Valves 20 Hopkinsons SCHEDULE OF SHELL BOILER MOUNTINGS Quality assurance Weir Power & Industrial operates quality programmes to cover the full scope of their activities. Comprehensive quality systems have been

More information

BR 26d Ball valve. Stainless Steel. Application: Versions: Special versions:

BR 26d Ball valve. Stainless Steel. Application: Versions: Special versions: Application: Stainless Steel BR 26d Ball valve Tight-closing Ball valve made of stainless steel for corrosive media, especially to meet high process requirements in chemical plants: Nominal sizes DN 15

More information

Drain ball valve BR 21a

Drain ball valve BR 21a PTFE - lined Drain ball valve BR 21a Application: Tight-closing PTFE-lined drain ball valve for corrosive media, especially for high process demand in chemical plants: Nominal sizes DN 50 to DN 150 Nominal

More information

Gate valve S38 PN , DN , T max : 540 C

Gate valve S38 PN , DN , T max : 540 C Gate valve S38 40-100, DN 40 400, T max : 540 C Shut off gate valve with outsidescrew, rising stem, non-rising hand wheel, with bolted bonnet, with flanges or with butt weld ends, flexible or split wedge,

More information

Type 441 XXL 442 XXL. Facts. Flanged Safety Relief Valves spring loaded. The-Safety-Valve.com. Metric Units LWN E

Type 441 XXL 442 XXL. Facts. Flanged Safety Relief Valves spring loaded. The-Safety-Valve.com. Metric Units LWN E Type 441 442 Flanged Safety Relief Valves spring loaded Metric Units Facts The-Safety-Valve.com LWN 462.07-E Conventional design 40 Bolted Cap H1 18 Adjusting screw 19 Lock nut 69 Needle bearing 16 Upper

More information

Standard Valves Series Globe Valves Series Angle Valves Series Way-Valves

Standard Valves Series Globe Valves Series Angle Valves Series Way-Valves Installation, Operation, Maintenance Instructions Standard Valves Series 035 000 Globe Valves Series 031 000 Angle Valves Series 033 000 3-Way-Valves 1 GENERAL INFORMATION These instructions are designed

More information

GATE VALVES S 38 APPLICATION

GATE VALVES S 38 APPLICATION APPLICATION The gate valves of this design are controlled valves used as the shut-off units in the piping system. They can be used for water, saturated and superheated steam, gases, non-aggressive liquids,

More information

STEAM TURBINE BY-PASS AND STEAM CONDITIONING VALVE

STEAM TURBINE BY-PASS AND STEAM CONDITIONING VALVE STEAM TURBINE BY-PASS AND STEAM CONDITIONING VALVE Benefits Savings of up to US$ 200.000 per year in maintenance costs Production gains due to superior stability of the temperature control Operational

More information

ALC-3 BUTTERFLY VALVES NOMINAL PRESSURE NOMINAL SIZE MATERIALS CONNECTIONS DESIGN. ANSI Class PN DN

ALC-3 BUTTERFLY VALVES NOMINAL PRESSURE NOMINAL SIZE MATERIALS CONNECTIONS DESIGN. ANSI Class PN DN BUTTERFLY VALVES ALC-3 NOMINAL PRESSURE ANSI Class 150-600 PN 10-100 NOMINAL 2-80 DN 50-2000 MATERIALS Cast Iron Carbon Steel Low Alloy Steel CONNECTIONS Wafer Lugged Flanged Butt Weld DESIGN Eccentric

More information

Please note this is a condensed catalog. For a complete version, contact Velan directly.

Please note this is a condensed catalog. For a complete version, contact Velan directly. Please note this is a condensed catalog. For a complete version, contact Velan directly. VELAN VALVES IN POWER With an installed base covering over 300 nuclear power plants and over 2,000 thermal power

More information

Type K12. Forged Gate Valve with Pressure Sealed Bonnet Butt-Welded, Flanged DN PN Data Sheet Edition: EN 9 / 2015

Type K12. Forged Gate Valve with Pressure Sealed Bonnet Butt-Welded, Flanged DN PN Data Sheet Edition: EN 9 / 2015 PN 63 400 Forged Gate Valve with Pressure Sealed Bonnet Butt-Welded, Flanged Data Sheet Edition: EN 9 / 2015 MPOWER Engineering, a.s. Pod vinicí 2028/20, Modřany, 143 00 Praha 4, CZ T: +420 225 371 300,

More information

NORI 320 Globe valves PN DN Application Standard variants Operating data Materials Remarks Design

NORI 320 Globe valves PN DN Application Standard variants Operating data Materials Remarks Design Type series booklet 7653.1/8-10 NORI 320 Globe valves with gland packing with non-turning stem flanged or butt-weld ends ZXLF ZXSF PN 250-320 DN 65-200 Application In industrial plants, power stations,

More information

W91/W94 Series TEMPERATURE REGULATORS. Self-Operated Temperature Regulators. Design & Operation W91 Non-Indicating W94 Dial Thermometer

W91/W94 Series TEMPERATURE REGULATORS. Self-Operated Temperature Regulators. Design & Operation W91 Non-Indicating W94 Dial Thermometer Design & Operation W91 Non-Indicating W94 Dial Thermometer Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company CAPILLARY

More information

Series 240 Pneumatic On-off Valve Type 3351

Series 240 Pneumatic On-off Valve Type 3351 Series 240 Pneumatic On-off Valve Type 3351 Application Control valve with a tight shutoff of liquids, gases and steam in accordance with DIN or ANSI standards Nominal sizes DN 15 to 100 NPS ½ to 4 Nominal

More information

Fasani Pressure Seal Cast Gate Valves - Style A Wedge Gate and Parallel Slide

Fasani Pressure Seal Cast Gate Valves - Style A Wedge Gate and Parallel Slide A series of robust gate valves specifically designed for applications in the power industry Features General application Our pressure seal -Style A gate valves are recommended for several applications

More information

HYDRAULIC CONTROL VALVES

HYDRAULIC CONTROL VALVES HYDRAULIC CONTROL VALVES The automatic control valves are diaphragm valves designed to provide hydraulically driven solutions to pressure, flow and level control applications. Features: Main valve uses

More information

RAIMONDI. High pressure forged globe valves to guarantee the pressure envelope integrity on harsh services.

RAIMONDI. High pressure forged globe valves to guarantee the pressure envelope integrity on harsh services. Fig. 6022-6025 RAIMONDI High pressure forged globe valves to guarantee the pressure envelope integrity on harsh services. Features Forged body materials of highest quality, all in compliance with ASME

More information

HANCOCK 600 GATE, GLOBE AND CHECK VALVES FORGED STEEL

HANCOCK 600 GATE, GLOBE AND CHECK VALVES FORGED STEEL HANCOCK 600 GATE, GLOBE AND CHECK VALVES A range of ASME class 800 and 1500 reduced bore forged steel valves with screwed, socket weld, butt weld or flanged ends GATE VALVES A compact but extremely sturdy

More information

Excess pressure regulator Excess pressure regulator, straight through DN

Excess pressure regulator Excess pressure regulator, straight through DN ARI-PREDEX Excess pressure regulator Excess pressure regulator, straight through DN 15-150 ARI-PREDEX Excess pressure regulator, straight through with diaphragm actuator UDA Actuator with rolling diaphragm

More information

Series 240 Pneumatic Control Valve Type and Type Globe Valve Type 3241

Series 240 Pneumatic Control Valve Type and Type Globe Valve Type 3241 Series 240 Pneumatic Control Valve Type 3241-1 and Type 3241-7 Globe Valve Type 3241 Application Control valve for process engineering and industrial applications Nominal size DN 15 to 300 Nominal pressure

More information

High Flow Safety Valves

High Flow Safety Valves High Flow Safety Valves Engineering GREAT Solutions Process and steam safety valves to PED and DIN/EN standards High Flow Safety Valves Valve summary Si 6301 Size DN 20 to DN 150 Set Pressure up to16 bar

More information

VALFONTA PRESSURE REGULATOR WITHOUT AUXILIARY ENERGY EXCESS PRESSURE VALVE (PRESSURE RELIEF VALVE) MODEL S1 MAIN CHARACTERISTICS

VALFONTA PRESSURE REGULATOR WITHOUT AUXILIARY ENERGY EXCESS PRESSURE VALVE (PRESSURE RELIEF VALVE) MODEL S1 MAIN CHARACTERISTICS PRESSURE REGULATOR WITHOUT AUXILIARY ENERGY EXCESS PRESSURE VALVE (PRESSURE RELIEF VALVE) MODEL S1 MAIN CHARACTERISTICS The S1 model is self-operated bellows sealed pressure excess valve. This series of

More information

Pressure Reducing Valve Type 2114/2415

Pressure Reducing Valve Type 2114/2415 Pressure Reducing Valve Type 2114/2415 Fig. 1 Type 2114/2415 1. Design and principle of operation The Type 2114/2415 Pressure Reducing Valve consists of the Type 2114 Valve and the Type 2415 Actuator.

More information

Pressure reducing valve Pressure reducing valve in straightway form DN

Pressure reducing valve Pressure reducing valve in straightway form DN Pressure reducing valve Pressure reducing valve in straightway form DN 15-150 ARI-PREDU Pressure regulating valve, straight through with diaphragm actuator DMA Actuator with rolling diaphragm Grey cast

More information

Series 240 Type Gas and Type Gas Automatic Shut-off Valves for Gases (valve class D)

Series 240 Type Gas and Type Gas Automatic Shut-off Valves for Gases (valve class D) Series 240 Type 3241-1-Gas and Type 3241-7-Gas Automatic Shut-off Valves for Gases (valve class D) DIN-DVGW typetested acc. to DIN EN 161 (2013-04) Application Control valve for control systems subject

More information

Type 644 and 645 Differential Pressure Pump Governors

Type 644 and 645 Differential Pressure Pump Governors Instruction Manual 644 and 645 Pump Governors Type 644 and 645 Differential Pressure Pump Governors Introduction Scope of Manual This instruction manual provides information on installation, adjustment,

More information

STAINLESS STEEL ARES PNEUMATIC ANGLE-SEAT VALVE

STAINLESS STEEL ARES PNEUMATIC ANGLE-SEAT VALVE FEATURES The stainless steel ARES valve is intended for the automatic shut-off of networks of fluids. The full-bore, inclined-seat body and the excellent flow-rate coefficients allow for very low pressure

More information

FORGED HIGH PRESSURE BONNETLESS. ASME CLASSES: Sizes: 1 2 4" ( mm) U.S. Patent # Patented Easy Maintenance!

FORGED HIGH PRESSURE BONNETLESS. ASME CLASSES: Sizes: 1 2 4 ( mm) U.S. Patent # Patented Easy Maintenance! FORGED HIGH PRESSURE BONNETLESS ASME CLASSES: 1690 4500 Sizes: 1 2 4" (15 100 mm) U.S. Patent # 4356832 Patented Easy Maintenance! PROFILE Velan is one of the world's leading manufacturers of industrial

More information

ACE VALVE COMPANY LIMITED

ACE VALVE COMPANY LIMITED Gate & Globe Valves ACE COMPANY LIMITED ttp://www.acevalve.co.kr Mangdeokri, Juchonmyun, Gimhae, Gyeongnam, Korea. TEL +000 FAX +0~ Email acevalve@acevalve.co.kr omepage www.acevalve.co.kr 0.0. ACE CATALOG

More information

AVK SERIES 55 AND 06 GATE VALVES, DN 450/500/600

AVK SERIES 55 AND 06 GATE VALVES, DN 450/500/600 AVK SERIES 55 AND 06 GATE VALVES, DN 450/500/600 1. Introduction The valve has a full and straight bore corresponding to the nominal diameter and can be installed independently of the flow direction. Although

More information

The GACHOT V501 gate valve offer the most possible reliability for process and critical applications

The GACHOT V501 gate valve offer the most possible reliability for process and critical applications The GACHOT V501 gate valve offer the most possible reliability for process and critical applications Features Construction complies with NF EN 1984 Straight-through flow and full port Cast body (investment

More information

ECOLINE GTC Type Series Booklet

ECOLINE GTC Type Series Booklet Gate Valve ECOLINE GTC 150-600 Class 150-600 NPS 2''-36'' Cast Steel / Stainless Steel Bolted Bonnet Flanged Ends Type Series Booklet Legal information/copyright Type Series Booklet ECOLINE GTC 150-600

More information

Type. Type 457, , 458. Flanged Safety Relief Valves spring loaded

Type. Type 457, , 458. Flanged Safety Relief Valves spring loaded Type Type 458 Packed lever H4 Closed bonnet Conventional design 457, 458 Flanged Safety Relief Valves spring loaded Contents Chapter/Page Materials Conventional design 09/02 Balanced bellows design 09/04

More information

TABLE OF CONTENT. 7-Operating mechanisms of Non-return valve with hydraulic damping cylinder

TABLE OF CONTENT. 7-Operating mechanisms of Non-return valve with hydraulic damping cylinder TABLE OF CONTENT Title 1- Tilting-Disc Non-Return valves with counter weight (NVTW) 2-Parts list 3-Installation Non-return valve and Butterfly Valve 4-Dimensions 5-Installation of Non-return valves with

More information

Standard Duty A.T.S.A. - Temp Desuperheater Model 24 / 34

Standard Duty A.T.S.A. - Temp Desuperheater Model 24 / 34 Narvik-Yarway covers requirements for desuperheaters, pneumatic actuators, strainers with a wide range of models, sizes and materials to satisfy all the specifications of the power, pulp & paper industry

More information

STAAL 40 AKD/AKDS Type Series Booklet

STAAL 40 AKD/AKDS Type Series Booklet Gate Valve STAAL 40 AKD/AKDS PN 10-40 DN 50-600 Type Series Booklet Legal information/copyright Type Series Booklet STAAL 40 AKD/AKDS All rights reserved. The contents provided herein must neither be distributed,

More information

Gate valve S38 PN , DN , T max : 540 C

Gate valve S38 PN , DN , T max : 540 C Gate valve S38 40-100, DN 40 400, T max : 540 C Shut off gate valve with outsidescrew, rising stem, non-rising hand wheel, with bolted bonnet, with flanges or with butt weld ends, flexible or split wedge,

More information

Type K03. Gate Valve Butt-Welded, Flanged DN PN Data Sheet Edition: EN 9 / together we are strong

Type K03. Gate Valve Butt-Welded, Flanged DN PN Data Sheet Edition: EN 9 / together we are strong PN 16 100 Gate Valve Butt-Welded, Flanged Data Sheet Edition: EN 9 / 2015 MPOWER Engineering, a.s. Pod vinicí 2028/20, Modřany, 143 00 Praha 4, CZ T: +420 225 371 300, F: +420 225 371 325 E: info@mpowergroup.eu,

More information

MSC Manifolds - DIN for Steam Distribution and Condensate Collection Installation and Maintenance Instructions

MSC Manifolds - DIN for Steam Distribution and Condensate Collection Installation and Maintenance Instructions 1170650/3 IM-P117-17 ST Issue 3 MSC Manifolds - DIN for Steam Distribution and Condensate Collection Installation and Maintenance Instructions 1 General safety information 2 General product information

More information

CAST STEEL FLANGED GATE, GLOBE, & CHECK VALVES.

CAST STEEL FLANGED GATE, GLOBE, & CHECK VALVES. CAST STEEL FLANGED GATE, GLOBE, & CHECK VALVES www.fnw.com Index Options & Accessories... 2 Standards... 2 Figure Number Matrix... 3 Pressure/Temperature Ratings... 3 Hydrostatic Test Pressures... 3 Carbon

More information

Si Safety valves for pressure relief in accordance to PED, DIN/EN and ASME. Engineering GREAT Solutions

Si Safety valves for pressure relief in accordance to PED, DIN/EN and ASME. Engineering GREAT Solutions Safety valves for pressure relief in accordance to PED, DIN/EN and ASME Engineering GREAT Solutions Features Typical regular safety valve for many applications The modern pressure safety valve for regular

More information

Valves for the industry. n Globe valves. n Gate valves. n Swing check valves

Valves for the industry. n Globe valves. n Gate valves. n Swing check valves Valves for the industry n Globe valves n Gate valves n Swing check valves 6100.1.05.14 n Prolog Industrial valves made by company Stahl-Armaturen PERSTA GmbH are designed according to DIN-Standards, EN-Standards

More information

Technical Description

Technical Description Technical Description 1. Assembly Sketch 2. Standard Part List Material indicated is for standard type. See specific appendix for other types. Item Part Description Material 1 Valve body 1.4301 2 Outlet

More information

Bulletin B Piston Valves

Bulletin B Piston Valves Bulletin B 04-20 BONETTI Piston Valves INDEX Page Rating 2 General Information 4 Construction Details 5-6 - Female Screwed Ends as per ASME 1.20.1 - API 602 - ASME 800 - Steel - size 3/8 2 6 - DIN PN 16

More information

Serie 2003/2013. Three-way Control Valve, mixing/diverting. Wörth am Main. Service. Control Valve Division

Serie 2003/2013. Three-way Control Valve, mixing/diverting. Wörth am Main. Service. Control Valve Division Serie 2003/2013 Three-way Control Valve, mixing/diverting Service Preventive maintenance Preventive maintenance primarily consists of making a regular visual inspection of the valve assembly. This can

More information

FASANI PRESSURE SEAL CAST GLOBE VALVES - STYLE B Y AND T PATTERN

FASANI PRESSURE SEAL CAST GLOBE VALVES - STYLE B Y AND T PATTERN A wide range of globe valves specifically designed for high pressure and high temperature applications, where low pressure loss is required. FEATURES GENERAL APPLICATION Our pressure seal globe valves

More information

THROUGH CONDUIT VALVES TECHNICAL CATALOGUE

THROUGH CONDUIT VALVES TECHNICAL CATALOGUE SITINDUSTRIE VALVO VALVES THROUGH CONDUIT VALVES Ed. 01/DIC-2004 SITINDUSTRIE reserves the right to change, without notice, 1/14 SITINDUSTRIE TRIE VALVE DIVISION We are pleased to introduce you to the

More information

Si Engineering GREAT Solutions. Process and steam safety valves to PED and DIN/EN standards

Si Engineering GREAT Solutions. Process and steam safety valves to PED and DIN/EN standards Engineering GREAT Solutions Process and steam safety valves to PED and DIN/EN standards Si 4302 Features Engineered with high discharge The state-of-the-art IMI Bopp & Reuther medium-pressure safety valve:

More information

brands you trust. CRANE - Cast Steel Valves

brands you trust. CRANE - Cast Steel Valves brands you trust. CRANE - Cast Steel Valves Features & Benefits Key Features & Benefits All seat rings are seal welded as standard Quality process fully documented, materials fully traceable Full range

More information

Compact Expanding Gate. Double Disc Parallel Slide ORION STEEL VALVES API 6D API 600

Compact Expanding Gate. Double Disc Parallel Slide ORION STEEL VALVES API 6D API 600 ORION STEEL VALVES Compact Expanding Gate API 6D Double Disc Parallel Slide API 600 PARALLEL SLIDE COMPACT EXPANDING GATE API 6D - DOUBLE DISC PARALLEL SLIDE API 600 - p. 155 Class ASME 150 (PN 20) 300

More information

INSTRUCTION MANUAL. Anchor Darling 1878 Swing Check Valves. Installation Operation Maintenance. Sizes 1/2 through 2 FCD ADENIM

INSTRUCTION MANUAL. Anchor Darling 1878 Swing Check Valves. Installation Operation Maintenance. Sizes 1/2 through 2 FCD ADENIM INSTRUCTION MANUAL Anchor Darling 1878 Swing Check Valves Sizes 1/2 through 2 Installation Operation Maintenance FCD ADENIM0006-00 Table of Contents 1.0 Physical Description and Operation of Equipment

More information

Data Sheet T EN

Data Sheet T EN Data Sheet T 8015-1 EN Series 240 Types 3241 1 PSA, -7 PSA, -9 PSA Pneumatic Control Valves Type 3241 PSA Globe Valve Application Control valves for PSA plants (Pressure Swing Adsorption) Valve sizes DN

More information

KE Series. Through Conduit, Double Expanding Gate Valves

KE Series. Through Conduit, Double Expanding Gate Valves KE Series Through Conduit, Double Expanding Gate Valves The KE Series is an advanced API 6D designed gate valve that provides a tight mechanically activated seal. It has double sealing, bi-directional

More information

Designed to provide maximum service life with minimum maintenance.

Designed to provide maximum service life with minimum maintenance. Designed to provide maximum service life with minimum maintenance. Fastest In-Line Repair Repairable in-line more easily and at less cost than any other valve. Stem, disc, and packing can be quickly removed

More information

Instructions for installation, operation and maintenance of: GATE VALVE

Instructions for installation, operation and maintenance of: GATE VALVE Instructions for installation, operation and maintenance of: GATE VALVE GEN GAC GAF/GENF TERMOVENT SC Temerin Republic of Serbia Instruction for installation, operation and maintenance: Table of Contents

More information

KNIFE GATE VALVES -- MODEL D

KNIFE GATE VALVES -- MODEL D PRODUCT DESCRIPTION Flanged unidirectional knife gate valve for high pressure applications One piece integral cast body with seating wedges and bolted bonnet. High flow rates with low pressure drops. Several

More information

High CATALOG. Efficiency. Pilot Operated Safety Valves Series 810 Pop Action Series 820 Modulate Action. The-Safety-Valve.com

High CATALOG. Efficiency. Pilot Operated Safety Valves Series 810 Pop Action Series 820 Modulate Action. The-Safety-Valve.com High Efficiency Pilot Operated Safety Valves Series 10 Pop Action Series 20 Modulate Action CATALOG The-Safety-Valve.com Valve finder How to find the right product group High operating to set pressure

More information

SEMPELL TURBINE BYPASS VALVE MODEL 115 CHP

SEMPELL TURBINE BYPASS VALVE MODEL 115 CHP A range of high pressure turbine bypass valves that provide greater reliability under extreme conditions. FEATURES Pressure reduction by multi-stage controlled expansion Atomizing steam desuperheater,

More information

Type 431, 433. Balanced bellows design. Type Cap H2. 18 Adjusting screw with bushing. 19 Lock nut. 16 Upper spring plate. 12 Spindle.

Type 431, 433. Balanced bellows design. Type Cap H2. 18 Adjusting screw with bushing. 19 Lock nut. 16 Upper spring plate. 12 Spindle. Balanced bellows design 40 Cap H2 18 Adjusting screw with bushing 19 Lock nut 16 Upper spring plate 12 Spindle 9 Bonnet 54 Spring 14 Split ring 17 Lower spring plate 55 Stud 56 Nut 8 Guide with bushing

More information

Series 240 Type and Type Pneumatic Control Valves Type 3244 Three-way Valve

Series 240 Type and Type Pneumatic Control Valves Type 3244 Three-way Valve Series 240 Type 3244-1 and Type 3244-7 Pneumatic Control Valves Type 3244 Three-way Valve DIN and ANSI versions Application Mixing or diverting valve for process engineering and industrial applications

More information

Three-Way Metal Seated Ball Valve Type 21-M

Three-Way Metal Seated Ball Valve Type 21-M Three-Way Metal Seated Ball Valve Type 21-M Design Characteristics Split body Trunnion mounted ball with - or T-port and integral stem ive loaded stem packing Spring loaded seat system Fire Safe design

More information

Product Overview SAFETY valves. Sempell ǀ product overview SAFETY valves

Product Overview SAFETY valves. Sempell ǀ product overview SAFETY valves SEMPELL Product Overview SAFETY valves Sempell ǀ product overview SAFETY valves 2 ǀ PENTAIR VALVES & CONTROLS A GLOBAL NETWORK OF INTERNATIONAL BRANDS PENTAIR VALVES & CONTROLS IS THE NAME BEHIND THE WORLD

More information

INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

INSTALLATION, OPERATION, AND MAINTENANCE MANUAL INSTALLATION, OPERATION, AND MAINTENANCE MANUAL MODEL 4D-200 REDUCED PRESSURE PRINCIPLE (RPZ) & MODEL 4D-700 REDUCED PRESSURE DETECTOR ASSEMBLY (RPDA) BACKFLOW PREVENTERS 2 ½ 10 Conbraco Industries Inc.

More information

Type 441 DIN 442 DIN. Facts. Flanged Safety Relief Valves spring loaded. The-Safety-Valve.com. US Units

Type 441 DIN 442 DIN. Facts. Flanged Safety Relief Valves spring loaded. The-Safety-Valve.com. US Units Type 441 DIN 442 DIN Flanged Safety Relief Valves spring loaded US Units Facts The-Safety-Valve.com LWN 462.02-E 462.01-D Conventional design 40 Cap H2 18 Adjusting screw 19 Lock nut 16 Upper spring plate

More information

SEMPELL HIGH PRESSURE CHECK VALVE MODEL VR500 (ASME)

SEMPELL HIGH PRESSURE CHECK VALVE MODEL VR500 (ASME) Designed for use in high temperature and high pressure systems wherever a reverse flow has to be avoided. FEATURES Piston type check valve Body made of forged steel Wear resistant stellite body seat Separated

More information

Si Engineering GREAT Solutions. Steam Safety Valves to PED and DIN/EN standards

Si Engineering GREAT Solutions. Steam Safety Valves to PED and DIN/EN standards Engineering GREAT Solutions Steam Safety Valves to PED and DIN/EN standards Engineered specific for HP steam application Features The IMI Bopp & Reuther high pressure steam safety valve: > Solid inlet

More information

BR 20b Ball valve. PFA-lined. Application: Versions:

BR 20b Ball valve. PFA-lined. Application: Versions: PFA-lined BR 20b Ball valve Application: Tight-closing PFA-lined ball valve for (highly) corrosive media, especially with high process demands in chemical plants: Nominal sizes DN 25 to DN 200 Nominal

More information

Series 42 Self-operated Regulators. Type RS Check Valve (backflow protection)

Series 42 Self-operated Regulators. Type RS Check Valve (backflow protection) Series 42 Self-operated Regulators Type 42-10 RS Check Valve (backflow protection) Application Designed to protect nitrogen and compressed air networks against backflow from directly connected systems.

More information

Si 6303 / Si 6304 / Si 6305

Si 6303 / Si 6304 / Si 6305 Si 6303 / Si 6304 / Si 6305 Engineering GREAT Solutions Process and steam safety valves to PED and DIN/EN standards Si 6303 / Si 6304 / Si 6305 Si 6303 / Si 6304 / Si 6305 Features Engineered for high

More information

Fisher 644 and 645 Differential Pressure Pump Governors

Fisher 644 and 645 Differential Pressure Pump Governors Instruction Manual 644 and 645 Pump Governors Fisher 644 and 645 Differential Pressure Pump Governors Contents Introduction... 1 Scope of Manual... 1 Description... 1 Specifications... 2 Educational Services...

More information

Series 240 Pneumatic Control Valve Type and Type Globe Valve Type 3241

Series 240 Pneumatic Control Valve Type and Type Globe Valve Type 3241 Series 240 Pneumatic Control Valve Type 3241-1 and Type 3241-7 Globe Valve Type 3241 Application Control valve for process engineering and industrial applications Nominal size 15 to 300 Nominal pressure

More information