Mazda3 - Workshop Manual - Engine

Size: px
Start display at page:

Download "Mazda3 - Workshop Manual - Engine"

Transcription

1 Page 1 of Mazda3 - Workshop Manual - Engine TIMING CHAIN REMOVAL/INSTALLATION WARNING: Fuel vapor is hazardous. It can very easily ignite, causing serious injury and damage. Always keep sparks and flames away from fuel. Fuel line spills and leakage are dangerous. Fuel can ignite and cause serious injuries or death and damage. Fuel can also irritate skin and eyes. To prevent this, always complete the "Fuel Line Safety Procedure". (See Fuel Line Safety Procedure.) 1. Remove the following parts. a. Plug hole plate (See PLUG HOLE PLATE REMOVAL/INSTALLATION.) b. Plug hole plate bracket c. Accelerator cable and bracket d. Battery cover (See BATTERY REMOVAL/INSTALLATION.) 2. Disconnect the negative battery cable. 3. Remove the following parts. a. Ignition coils (See IGNITION COIL REMOVAL/INSTALLATION.) b. Front wheel and tire (RH) (See GENERAL PROCEDURES (SUSPENSION).) c. Under cover and splash shields d. Crankshaft position (CKP) sensor (See CRANKSHAFT POSITION (CKP) SENSOR REMOVAL/INSTALLATION.) e. Drive belt (See DRIVE BELT REPLACEMENT.) f. A/C compressor with the oil hose still connected and position the A/C compressor so that it is out of the way (See A/C COMPRESSOR REMOVAL/INSTALLATION.) g. Coolant reserve tank with the hose still connected and position the coolant reserve tank so that it is out of the way 4. Remove in the order indicated in the table. 5. Install in the reverse order of removal.

2 Page 2 of Start the engine. 7. Inspect the following and adjust if necessary. Pulley and belt for runout and contact Leakage of engine oil Ignition timing, idle speed, and amount of CO and HC (See ENGINE TUNE-UP.) Engine-driven accessories operation

3 Page 3 of 18

4 Page 4 of 18 1 Cylinder head cover (See Cylinder Head Cover Installation Note.) 2 Crankshaft pulley lock bolt (See Crankshaft Pulley Lock Bolt Removal Note.) (See Crankshaft Pulley Lock Bolt Installation Note.) 3 Crankshaft pulley 4 Water pump pulley 5 Drive belt auto tensioner 6 No.3 engine mount rubber and No.3 engine joint bracket (See No.3 Engine Mount Rubber Removal Note.) (See No.3 Engine Mount Rubber and No.3 Engine Mount Bracket Installation Note.) 7 Engine front cover (See Engine Front Cover Installation Note.) 8 Front oil seal (See Engine Front Cover Removal Note.)

5 Page 5 of 18 (See Front Oil Seal Installation Note.) 9 Chain tensioner (See Chain Tensioner Removal Note.) 10Tensioner arm 11Chain guide 12Timing chain (See Timing Chain Installation Note.) 13Oil pump chain tensioner 14Oil pump chain guide 15Oil pump sprocket (See Oil Pump Sprocket Removal Note.) (See Oil Pump Sprocket Installation Note.) 16Oil pump chain 17Crankshaft sprocket Crankshaft Pulley Lock Bolt Removal Note 1. Remove the cylinder block lower blind plug. 2. Install the SST.

6 Page 6 of Turn the crankshaft clockwise the crankshaft is in the No.1 cylinder TDC position (until the balance weight is attached to the SST). 4. Hold the crankshaft pulley using the SSTs. No.3 Engine Mount Rubber Removal Note 1. To install the front shaft (RH) of the SST (49 C017 5A0), remove the clip shown the figure.

7 Page 7 of Install the SST using the following procedure. CAUTION: Refer to the SST instruction manual for the basic handing procedure. a. Install the right rear shaft of the SST to the bolt of the right shock absorber as shown in the figure.

8 Page 8 of 18 b. Install the left rear shaft of the SST to the bolt of the left shock absorber. (identical position to the right side) c. Install front foot No.2 to the left/right front shaft of the SST, then align the groove of the front shaft of the SST with the folded up part of the vehicle as shown in the figure.

9 Page 9 of 18 d. Adjust the positions of the SST side bars so that they are the same height (left and right) and horizontal. e. Make sure each joint is securely tightened. 3. Suspend the engine using the SST. Engine Front Cover Removal Note 1. Remove the oil seal using a screwdriver as shown in the figure. Chain Tensioner Removal Note 1. Unlock the chain tensioner ratchet using a suitable screw driver or equivalent tool.

10 Page 10 of Slowly compress the tensioner piston. 3. Hold the tensioner piston using a 1.5 mm {0.059 in} wire or paper clip. Oil Pump Sprocket Removal Note 1. Temporarily install the crankshaft pulley and crankshaft pulley lock bolt to the crankshaft, and lock the oil pump against rotation as shown in figure. 2. Remove the oil pump sprocket, and then remove the crankshaft pulley and crankshaft pulley lock bolt. Oil Pump Sprocket Installation Note 1. Temporarily install the crankshaft pulley and crankshaft pulley lock bolt to the crankshaft, and lock the oil pump against rotation as shown in figure.

11 Page 11 of Install the oil pump sprocket, and then remove the crankshaft pulley and crankshaft pulley lock bolt. Tightening torque Timing Chain Installation Note 2030 Nm { kgfm, ftlbf} 1. Install the SST to the camshaft as shown in the figure. 2. Install the timing chain. 3. Remove the retaining wire or paper clip from the auto tensioner to apply tension to the timing chain. Engine Front Cover Installation Note 1. Apply silicone sealant to the engine front cover as shown in the figure.

12 Page 12 of 18 CAUTION: Thickness Install the engine front cover before the applied silicone sealant starts to harden. Silicone sealant is not need in area C as indicated below due to an existing. (L3 (with variable valve timing mechanism)) Completely remove any oil, dirt, sealant, or other foreign matter adhering to the engine front cover and engine front cover installation surface. If any oil, dirt, sealant, or other foreign matter is not removed from the space between the engine front cover and engine front cover installation surface, it may cause a sealing malfunction. A: mm { in} B: mm { in} 2. Install the engine front cover bolts in the order shown in the figure.

13 Page 13 of 18 Bolt No. Tightening torque Nm { kgfcm, inlbf} Nm { kgfm, ftlbf} Nm { kgfm, ftlbf} Front Oil Seal Installation Note 1. Apply clean engine oil to the oil seal.

14 Page 14 of Push the oil seal slightly in by hand. 3. Compress the oil seal using the SST and a hammer. No.3 Engine Mount Rubber and No.3 Engine Mount Bracket Installation Note 1. Tighten the stud bolt of the No.3 engine mount bracket.

15 Page 15 of 18 Tightening torque Nm { kgfcm, inlbf} NOTE: Tightening stud bolt when the nut of No.3 engine mount nut is loosened. 2. Hand-tighten the No.3 engine mount rubber and No.3 engine mount bracket. 3. Tighten the bolts and nuts in the order as shown in the figure. Tightening torque Nuts : Nm { kgfm, ftlbf} Bolts : Nm { kgfm, ftlbf} Crankshaft Pulley Lock Bolt Installation Note 1. Install the SST to the camshaft as shown in the figure. 2. Install the M6 x 1.0 bolt in by hand.

16 Page 16 of Turn the crankshaft clockwise until the crankshaft is in the No.1 cylinder TDC position (until the balance weight is attached to the SST). 4. Hold the crankshaft pulley using the SST. 5. Tighten the crankshaft pulley lock bolt in the order shown with the following two steps using the SST (49 D ). Tightening torque (1) Nm { kgfm, ftlbf} (2) Remove the M6 x 1.0 bolt. 7. Remove the SST from the camshaft. 8. Remove the SST from the cylinder block lower blind plug.

17 Page 17 of Rotate the crankshaft clockwise two turns until the TDC position. If not aligned, loosen the crankshaft pulley lock bolt and repeat from Step Install the cylinder block lower blind plug. Tightening torque 1822 Nm { kgfm, ftlbf} Cylinder Head Cover Installation Note 1. Apply silicone sealant to the mating faces as shown in the figure. CAUTION: Install the cylinder head cover within 10 min of applying the silicone sealant. Thickness mm { in} 2. Install the cylinder head cover with a new gasket. 3. Tighten the bolts in the order shown in the figure.

18 Page 18 of 18 Tightening torque Nm {8296 kgfcm, 7184 inlbf}

3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]

3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1 of 17 TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Disconnect the negative battery cable. 2. Remove the under cover. 3. Remove the front wheels and tires (RH). 4. Remove the splash shield. 5. Remove

More information

4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)

4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].) TIMING CHAIN REMOVAL/INSTALLA... < Previous Next > 2007 Mazda3 Engine TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Remove the battery cover. 2. Disconnect the negative battery cable. 3. Remove the

More information

TIMING BELT REMOVAL/INSTALLATION [ZM]

TIMING BELT REMOVAL/INSTALLATION [ZM] ALLDATA Online - 2000 Mazda Protege LX L4-6L DOHC - Service an... 1 of 8 6/26/2012 7:53 PM TIMING BELT REMOVAL/INSTALLATION [ZM] 5. 6. 7. 8. 9. Disconnect the negative battery cable. Remove the CMP sensor.

More information

TIMING CHAIN COMPONENTS

TIMING CHAIN COMPONENTS Page 1 of 30 TIMING CHAIN COMPONENTS Fig. 46: Identifying Camshaft Timing Oil Control Valve Assembly Components With Torque Page 2 of 30 Specifications (1 Of 3) Fig. 47: Identifying Camshaft Timing Oil

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender

More information

Page 1 of 44 REPLACEMENT 1. 2. 3. 4. REMOVE ENGINE UNDER COVER RH DRAIN COOLANT (See REPLACEMENT ) REMOVE FRONT WHEEL RH REMOVE CYLINDER HEAD COVER NO. 2 a. Remove the 2 nuts, 2 clips and cylinder head

More information

FRONT SUSPENSION LOCATION INDEX

FRONT SUSPENSION LOCATION INDEX 1. Remove the front suspension tower bar. (See FRONT SUSPENSION TOWER BAR REMOVAL/INSTALLATION.) 2007 Mazda MX-5 Miata Sport 2007 SUSPENSION Front Suspension - MX-5 Miata FRONT SUSPENSION LOCATION INDEX

More information

2010 Transit Connect Workshop Manual. 31. Remove the 3 bolts, thermostat housing and thermostat.

2010 Transit Connect Workshop Manual. 31. Remove the 3 bolts, thermostat housing and thermostat. 31. Remove the 3 bolts, thermostat housing and thermostat. 32. Remove the 2 bolts, stud bolt and the A/C compressor. 33. Remove the bolt and the KS. 34. Remove the 8 bolts and the crankcase vent oil separator.

More information

Mazda North American Operations Irvine, CA

Mazda North American Operations Irvine, CA Service Bulletin Mazda North American Operations Irvine, CA 92618-2922 Subject: VARIABLE VALVE TIMING (VVT) NOISE AND/OR TIMING CHAIN NOISE Bulletin No: 01-012/12 MULTI-MODEL (L3 TURBO) - VARIABLE VALVE

More information

VALVE CLEARANCE (K3-VE)

VALVE CLEARANCE (K3-VE) ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT

More information

IN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Disconnect the eight ignition coil electrical connectors.

IN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Disconnect the eight ignition coil electrical connectors. 303-01A-1 IN-VEHICLE REPAIR Timing Drive Components 303-01A-1 Special Tool(s) Compressor, Valve Spring 303-581 (T97T-6565-A) Holding Tool, Crankshaft 303-448 (T93P-6303-A) 3. Disconnect the eight ignition

More information

2011 > G 1.6 DOHC > Language. [MDPS Type] Loosen the mounting bolts (A) and then, turn the adjusting bolt(b) clockwise in loose tension.

2011 > G 1.6 DOHC > Language. [MDPS Type] Loosen the mounting bolts (A) and then, turn the adjusting bolt(b) clockwise in loose tension. 2011 > G 1.6 DOHC > Language Removal Engine removal is not required for this procedure. 1. Disconnect the battery negative terminal. 2. Loosen the water pump pulley bolt and the drive idler mounting bolt.

More information

EG1 509 OIL COOLER COMPONENTS FOR REMOVAL AND INSTALLATION

EG1 509 OIL COOLER COMPONENTS FOR REMOVAL AND INSTALLATION 3SGTE ENGINE EG1509 OIL COOLER COMPONENTS FOR REMOVAL AND INSTALLATION EG1510 3SGTE ENGINE 3SGTE ENGINE EG1511 OIL COOLER REMOVAL (See Components for Removal and Installation) 1. DISCONNECT CABLE FROM

More information

TIMING BELT COMPONENTS

TIMING BELT COMPONENTS EG134 3SGTE ENGINE TIMING BELT COMPONENTS 3SGTE ENGINE EG135 EG136 3SGTE ENGINE 3SGTE ENGINE TIMING BELT REMOVAL EG137 (See Components for Removal and Installation) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL

More information

CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.

CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly. Installation Engines with ratcheting timing chain tensioners 1. CAUTION: Timing chain procedure must be followed exactly or damage to valves and pistons will result. CAUTION: Do not compress the ratchet

More information

2003 Taurus/Sable Workshop Manual

2003 Taurus/Sable Workshop Manual Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)

More information

ENGINE SPECIFICATIONS

ENGINE SPECIFICATIONS ENGINE SPECIFICATIONS MECHANICAL LOCATION INDEX Engine cover 1 (See ENGINE COVER REMOVAL/INSTALLATION.) 2 Drive belt Page 1 (See DRIVE BELT DEFLECTION/TENSION INSPECTION.) (See DRIVE BELT ADJUSTMENT.)

More information

TIMING CHAIN COMPONENTS

TIMING CHAIN COMPONENTS h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:

More information

FUEL PUMP SYSTEM CIRCUIT

FUEL PUMP SYSTEM CIRCUIT EG190 FUEL PUMP SYSTEM CIRCUIT ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SST, connect terminals +B and FP of the DLC1. SST 0984318020 (b) Turn the ignition switch ON. NOTICE: Do not start

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

Intake Components 1117

Intake Components 1117 Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air

More information

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation. TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan

More information

Engine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)

Engine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH) Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,

More information

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE 1. Disconnect negative battery cable. Drain cooling system. Remove front strut bar and strut brackets, if equipped. 2. Disconnect Intake Air Temperature (IAT) sensor harness connector. Remove air cleaner

More information

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin... Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine

More information

FUEL PUMP SYSTEM CIRCUIT

FUEL PUMP SYSTEM CIRCUIT EG199 FUEL PUMP SYSTEM CIRCUIT ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SSt, connect terminals +B and FP of the data link connector 1. SST 0984318020 (b) Turn the ignition switch ON.

More information

1999 Honda Accord DX

1999 Honda Accord DX Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are

More information

& MX Loosen the righthand front wheel lug nuts, then raise and support the vehicle with jack stands.

& MX Loosen the righthand front wheel lug nuts, then raise and support the vehicle with jack stands. Vehicle: 1996 MAZDA 626: DX 2.0L L4 GAS-FI-N Content: Engine Service >> Timing Belt >> Timing Belt, Replace 1993-97 626 & MX-6 This engine is classified as an Interference engine. If the timing belt breaks

More information

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right

More information

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly. Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE

More information

TIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage

TIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:

More information

file://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...

file://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref... Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor

More information

TIMING BELT COMPONENTS EM 15

TIMING BELT COMPONENTS EM 15 ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work

More information

Timing Drive Components Camshaft Timing

Timing Drive Components Camshaft Timing SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner

More information

Testing and Inspection. Diagnostic Procedure Step 1-2

Testing and Inspection. Diagnostic Procedure Step 1-2 1 of 4 5/22/2008 7:54 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Nissan-Datsun Altima 2.5 S L4-2.5L (QR25DE) Vehicle

More information

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) 1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15

More information

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with

More information

REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.

REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration. 21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine

More information

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) 2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475

More information

VALVE CLEARANCE ADJUSTMENT EM 7

VALVE CLEARANCE ADJUSTMENT EM 7 GR-FE ENGE MECHANICAL VALVE CLEARANCE VALVE CLEARANCE ADJUSTMENT 7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMAL 2. DRA ENGE COOLANT (See page CO-3) 3. ROVE V-BANK COVER (See page ES-44) 4. ROVE AIR CLEANER

More information

2002 Escape Workshop Manual

2002 Escape Workshop Manual SECTION 303-01B: Engine 3.0L (4V) IN-VEHICLE REPAIR Procedure revision date: 10/09/2003 Timing Drive Components Removal CAUTION: Failure to verify correct timing drive component alignment will result in

More information

Remove four nuts, then the cooling fan assembly.

Remove four nuts, then the cooling fan assembly. The DOHC and SOHC engines both use the same Service and Repair procedure from Isuzu. Make note that the DOHC and SOHC engines both use a single gear for the camshaft but use different alignment marks.

More information

Timing Drive Components ( )

Timing Drive Components ( ) Page 1 of 14 (12.65.13) Removal 1. Remove the engine front cover. For additional information, refer to For additional information, refer to. 2. Remove the spark plugs. 3. Remove the crankshaft position

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory

More information

3/13/ :32 AM. NOTICE: Do not disconnect the hose.

3/13/ :32 AM. NOTICE: Do not disconnect the hose. 1 of 25 REPLACEMENT 1. REMOVE HOOD SUB-ASSEMBLY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT FENDER APRON SEAL RH 6. DRAIN ENGINE OIL a. Install

More information

2000 Toyota Truck Tundra. Timing Belt: Service and Repair

2000 Toyota Truck Tundra. Timing Belt: Service and Repair Timing Belt: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY 4. REMOVE THROTTLE BODY COVER 5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY 6. REMOVE

More information

Service and Repair CAMSHAFT

Service and Repair CAMSHAFT Service and Repair CAMSHAFT Removal and Installation REMOVAL 1. Remove front timing chain case, camshaft sprocket, timing chain and rear timing chain case. Refer to "REMOVAL". 2. Remove camshaft position

More information

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE HONDA 2.2L & 2.3L 4-Cylinder - DOHC & SOHC - 1990-97 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1990-94 vehicles, the manufacturer recommends camshaft and balance shaft belts be replaced at 90,000

More information

2001 Toyota MR ENGINES' '1.8L 4-Cylinder

2001 Toyota MR ENGINES' '1.8L 4-Cylinder TIMING CHAIN Removal 1. Disconnect negative battery cable. Drain cooling system. On Corolla, remove windshield washer fluid reservoir. On Celica, remove upper front fender apron seal and upper radiator

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION Page 1 of 11 REMOVAL & INSTALLATION TIMING BELT Tips Click a link to view tip Tech1 Question: Timing problems P0340 Tech1 Question: 2.2 TIMING PROBLEMS - RESOLVED Removal Tips Click a link to view tip

More information

2002 Crown Victoria/Grand Marquis Workshop Manual

2002 Crown Victoria/Grand Marquis Workshop Manual Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper

More information

Timing Chain: Service and Repair

Timing Chain: Service and Repair 2005 Nissan-Datsun Altima L4-2.5L (QR25DE) Copyright 2013, ALLDATA 10.52SS Page 1 Timing Chain: Service and Repair TIMING CHAIN Removal and Installation Apply new engine oil to parts marked in illustration

More information

TIMING CHAIN. TIMING CHAIN Removal and Installation EM-35 PFP:13028 EBS00I2X KBIA2511E

TIMING CHAIN. TIMING CHAIN Removal and Installation EM-35 PFP:13028 EBS00I2X KBIA2511E TIMING CHAIN Removal and Installation PFP:13028 EBS00I2X A EM C D E F G H I J K L M KBIA2511E EM-35 1. Camshaft sprocket (left bank EXH) 2. Camshaft sprocket (left bank INT) 3. Camshaft sprocket (right

More information

Page 1 of 75 303-01D Engine - 5.2L 32V Ti-VCT 2016 Mustang Assembly Procedure revision date: 12/15/2016 Special Tool(s) / General Equipment Engine Base Part Number: 6L084 205-142 (T80T-4000-J) Installer,

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower

More information

EG-37 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZ-GE

EG-37 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZ-GE ENGINE EG37 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZGE EG38 ENGINE 2JZ GTE ENGINE EG39 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. REMOVE BATTERY AND BATTERY TRAY

More information

CLUTCH COMPONENT LOCATION INDEX

CLUTCH COMPONENT LOCATION INDEX 2005 TRANSMISSION Clutch - MX-5 Miata CLUTCH COMPONENT LOCATION INDEX Fig. 1: Identifying Clutch Components GENERAL PROCEDURES (CLUTCH) PRECAUTION Clutch pipe If any clutch pipe has been disconnected anytime

More information

DISTRIBUTOR DISTRIBUTOR REMOVAL

DISTRIBUTOR DISTRIBUTOR REMOVAL IG12 (5SFE) DISTRIBUTOR DISTRIBUTOR REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION (w / Airbag): Work must be started after approx. 30 seconds or longer from the time the ignition

More information

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR) SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,

More information

1990 Buick Electra Limited

1990 Buick Electra Limited 4. To install remaining components, reverse removal procedure. Coat rocker arm bolts with GM Threadlock (12345493) prior to installation. Fig. 3: Cylinder Head Bolt Tightening Sequence FRONT CRANKSHAFT

More information

Cylinder Head. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Compressor, Valve Spring

Cylinder Head. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Compressor, Valve Spring SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 03/15/2009 Cylinder Head Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039

More information

2002 Explorer Sport/Sport Trac Workshop Manual

2002 Explorer Sport/Sport Trac Workshop Manual Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)

More information

2002 Escape Workshop Manual

2002 Escape Workshop Manual SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft

More information

SECTION C Engine 5.4L (4V)

SECTION C Engine 5.4L (4V) 303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE IN-VEHICLE REPAIR Timing Drive Components... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 IN-VEHICLE REPAIR Timing

More information

2/17/2017 Timing Belt Service and Repair, Removal and Replacement

2/17/2017 Timing Belt Service and Repair, Removal and Replacement http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com

More information

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (200SX & 300ZX)

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick.

SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. EG45 ONVEHICLE INSPECTION 1. INSPECT OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. (a) Park the vehicle on a level spot and turn the engine off. (b) 4WD: Remove the LH front

More information

1 of 10 2/10/2017 5:20 PM

1 of 10 2/10/2017 5:20 PM 1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION 303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589

More information

Compressor HVAC: Service and Repair

Compressor HVAC: Service and Repair Compressor HVAC: Service and Repair Cooler Compressor Assy REPLACEMENT 1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM SST 07110-58060 (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070,

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

Timing Belt: Service and Repair Timing Belt Replace. Timing Belt Removal

Timing Belt: Service and Repair Timing Belt Replace. Timing Belt Removal 1998 Toyota Corolla DX Sedan 4-Door L4-1762cc 1.8L DOHC MFI Page 1 Timing Belt: Service and Repair Timing Belt Replace Timing Belt Removal SPECIAL SERVICE TOOL (SST) REQUIRED ^ 09213-70010 Crankshaft Pulley

More information

REMOVAL. Cylinder Head. All cylinder heads. 1. Remove the engine. For additional information, refer to Engine in this section.

REMOVAL. Cylinder Head. All cylinder heads. 1. Remove the engine. For additional information, refer to Engine in this section. 303-01B-1 303-01B-1 REMOVAL Cylinder Head Material Item Specification Special Tool(s) Motorcraft Metal Surface Prep Modular Engine Lift Bracket ZC-31 303-F047 (014-00073) or equivalent Silicone Gasket

More information

EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION

EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER

More information

2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA Page 1

2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA Page 1 2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL

More information

ENGINE 6G74 3.5L-SOHC-24 VALVE

ENGINE 6G74 3.5L-SOHC-24 VALVE 11A ENGINE General Information/Service Specifications ENGINE 6G74 3.5L-SOHC-24 VALVE GENERAL INFORMATION Items Specifications Type V-type, Over Head Camshaft Number of cylinders 6 Bore mm 93.0 Stroke mm

More information

DISASSEMBLY. Engine. Special Tool(s) Locking Tool, Camshaft Phaser Sprocket Special Tool(s)

DISASSEMBLY. Engine. Special Tool(s) Locking Tool, Camshaft Phaser Sprocket Special Tool(s) 303-01B-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Rear Slinger 303-514 (T95P-6701-AH) Special Tool(s) 303-01B-1 Locking Tool, Camshaft Phaser Sprocket 303-1046 Remover, Crankshaft Rear Seal

More information

REPLACEMENT. 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2.

REPLACEMENT. 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2. ENGINE MECHANICAL 1475 REPLACEMENT 141FV01 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2. A66316 2. REMOVE IGNITION COIL NO.1 (a) Remove the 4 bolts and pull out

More information

TIMING BELT (5S FE) COMPONENTS

TIMING BELT (5S FE) COMPONENTS ENGINE MECHANICAL Timing Belt (5SFE) EM67 TIMING BELT (5SFE) COMPONENTS REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started after approx. 20 seconds

More information

Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage.

Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage. 1991 Daihatsu Truck Rocky L4-1589cc 1.6L SOHC Page 1 Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage. Repair any water leakage

More information

FI 135. Fuel Pump (3S GTE)

FI 135. Fuel Pump (3S GTE) Fuel System (Fuel Pump (3SGTE)) FI135 Fuel Pump (3SGTE) FI136 MFI AND SFI SYSTEMS Fuel System (Fuel Pump (3SGTE)) ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SST, connect terminals +B and

More information

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s) 303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket

More information

EG1 485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION

EG1 485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION EG1485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION EG1486 EG1487 EG1488 OIL PUMP REMOVAL (See Components for Removal and Installation) HINT: When repairing the oil pump, the oil pan an^ strainer should

More information

1995 Aerostar/Ranger/Explorer

1995 Aerostar/Ranger/Explorer Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and

More information

2000 Lincoln LS Workshop Manual

2000 Lincoln LS Workshop Manual Page 1 of 10 SECTION 303-01B: Engine 3.9L 2000 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 03/17/1999 Timing Drive Components Primary Special Tool(s) Camshaft Setting/Locking

More information

EM 112 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSPECTION. Intake Air Surge Tank Side

EM 112 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSPECTION. Intake Air Surge Tank Side 112 Intake Air Surge Tank Side Cylinder Head Side 1GR-FE ENGINE MECHANICAL ENGINE ASSBLY INSPECTION 1. INSPECT INTAKE MANIFOLD FOR WARPAGE (a) Using a precision straight edge and feeler gauge, measure

More information

2001 Dodge Dakota ENGINES 4.7L V8

2001 Dodge Dakota ENGINES 4.7L V8 FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.

More information

TECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump SERVICE DATE MODEL 2002 MY.

TECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump SERVICE DATE MODEL 2002 MY. SERVICE V8 XJ Series DATE 12/02 TECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump 100-21 MODEL 2002 MY V8 XJ Series VIN F44114 - F55936 Issue: Some 2002

More information

1992 Mitsubishi 3000GT VR-4

1992 Mitsubishi 3000GT VR-4 TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner

More information

TIMING BELT (3S FE) COMPONENTS

TIMING BELT (3S FE) COMPONENTS Timing Belt (3SFE) TIMING BELT (3SFE) COMPONENTS EM23 REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY 2. REMOVE RH FRONT WHEEL 3. REMOVE ENGINE RH UNDER COVER 4. REMOVE CRUISE

More information

INSTALLATION EM 8 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT CORRECT. Generator Vehicle Front A077960E03. Adjusting Bar. Bolt A. Bolt B.

INSTALLATION EM 8 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT CORRECT. Generator Vehicle Front A077960E03. Adjusting Bar. Bolt A. Bolt B. 8 CORRECT Adjusting Bar 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT Generator Vehicle Front A077960E03 INSTALLATION 1. INSTALL VANE PUMP V BELT (a) Temporarily install the belt on each pulley. 2. INSTALL

More information

1 of 12 11/20/2016 9:32 PM

1 of 12 11/20/2016 9:32 PM 1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing

More information

STEERING LOCATION INDEX

STEERING LOCATION INDEX STEERING LOCATION INDEX 2007 STEERING Power Steering - MX-5 Miata Fig. 1: Identifying Location Of Steering Components AIR BLEEDING CAUTION: Do not turn the steering wheel during the fluid level inspection,

More information

TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT

TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.

More information

DISASSEMBLY AND REASSEMBLY

DISASSEMBLY AND REASSEMBLY 24 01 DISASSEMBLY AND REASSEMBLY COMPONENTS AND SPECIAL TOOLS Injector Puller Y99220072B Glow Plug Wrench Y99220132B Fuel Pipe Wrench Sealing Caps 665 995 5844 Injector Copper Washer Puller Y99220022B

More information