CPO Commerce, LLC 60 Crestridge DR Suwanee, GA Customer service#:

Transcription

1 Model: 2200I Inverter Generator OPERATOR S MANUAL CPO Commerce, LLC 60 Crestridge DR Suwanee, GA Customer service#: customerservice@cpocommerce.com SAVE THIS MANUAL FOR FUTURE REFERENCE This manual contains important information regarding safety, operation, and maintenance.

2 TABLE OF CONTENTS Introduction...3 Parts Ordering / Customer Service...3 Safety Rules...4 Safety Symbols...4 Safety Instructions...4 Features...7 Control Panel Functions...8 ON/OFF Start Switch and Choke...8 Indicator Lights...8 DC Protector...9 Engine Smart Control (EMS)...9 Parallel Outlets...9 Fuel Cap Air Vent...10 Ground Terminal...10 Assembly...11 Connecting Generator to an Electrical System...11 Adding Fuel...11 Adding / Checking Oil...12 Operation...13 Grounding the Generator...13 How to Start Engine...13 How to Stop Engine...14 Attaching Electronic Devices...14 Charging a 12 Volt Battery...15 AC Parallel Operation...16 Don t Overload Generator...17 Wattage Reference Guide...17 Maintenance...18 Maintenance Schedule...18 Checking Spark Plug...19 Changing Oil...20 How to Clean Air Filter...21 How to Clean Fuel Filter...22 How to Store...22 Troubleshooting...24 Diagrams Wiring Diagram

3 INTRODUCTION Thank you for purchasing this superior quality portable generator. When operating and maintaining this product as instructed in this manual, your generator will give you many years of reliable service.. It is designed to supply electrical power to operate tools, appliances, camping equipment, lighting, or serve as a back up power source during power outages. AC Output DC Output Engine Rated AC Voltage Rated Frequency Rated Output Maximum Output USB Outlet Cigarette Outlet Displacement Engine Type Engine Oil Type Engine Oil Capacity Fuel Tank Capacity 120V 60Hz 1700W 2200W 5V DC 1.5A 12V DC 8A 80cc Single cylinder, 4 Stroke, OHV, Air Cooled SAE 10W30 350ml / 11.8oz 4.5L / 1.18Gal Emissions The United States Environmental Protection Agency (US EPA) (and California Air Resources Board (CARB), for engines/equipment certified to California standards) requires that this engine/equipment complies with exhaust and evaporative emissions stan-dards. Locate the emissions compliance decal on the engine to determine applicable stan-dards. For emissions warranty information, please reference the included emissions war-ranty. It is important to follow the maintenance specifications in the manual to ensure that the engine complies with the applicable emissions standards for the duration of the product s life. 3

4 SAFETY RULES Safety Symbols CAUTION! Indicates a potentially hazardous situation which could result in serious injury or death if not avoided. Indicates a potentially hazardous situation which could result in damage to equipment or property. Toxic Fumes Risk of explosion Risk of electric shock Hot surface Safety Instructions the user must understand and follow all manual instructions and use common sense. Read and understand this manual in its entirety before operating this generator. Improper use of this generator could result in serious injury or death. monoxide gas from dissipating. Using a generator indoors WILL KILL YOU IN MINUTES! Carbon monoxide gas is a poisonous, odorless gas that can cause headache, confusion, fatigue, nausea, fainting, sickness, seizures, or death. If you start to experience any of these symptoms, IMMEDIATELY get fresh air and seek medical attention. Install a battery operated carbon monoxide alarm near bedrooms. When working in areas where vapors could be inhaled, use a respirator mask according to all of its instructions. Engine exhaust contains chemicals that lead to cancer and cause birth defects. Always wash hands after handling generator. 4

5 SAFETY RULES Never exceed generators wattage / amperage capacity. This could damage the generator and / or connected electrical devices. Check operating voltage and frequency requirements of all electrical devices prior to plugging them into the generator. Never start or stop engine with electrical devices plugged in to the receptacles. Failure to do so could damage the generator and / or connected electrical devices. Always start the engine and let it stabilize before connecting any electronic devices. Disconnect all electronic devices before stopping the engine. Starter and other moving parts can catch on clothing, jewelry, and hair. Do not wear loose clothing or gloves. Remove jewelry or anything else that could be caught in moving parts. Tie back or wear protective head covering to contain long hair. death. on the unit before starting the engine. Never smoke while operating or fueling this unit. Generator should have at least 5 feet of clearance from buildings or other equipment during operation. When adding or draining fuel, unit should be turned off for at least 2 minutes to cool before removing fuel cap. If unit has been running then the fuel cap is under pressure, remove slowly. To keep fuel from spilling, secure unit so it cannot tip while operating or transporting. When transporting unit, disconnect the spark plug wire and make sure the fuel tank is empty with the 3 in 1 switch is turned to the off position. Pull cord recoils rapidly and pulls arm towards engine faster than you can let go which could result in injury. To avoid recoil, pull starter cord slowly until resistance is felt, then pull rapidly. Avoid contacting hot areas of this unit. Allow hot components to cool before touching. 5

6 SAFETY RULES This generator produces a very high voltage which could result in burn or electrocution causing serious injury or death. Never handle the generator, electronic devices, or any cord while standing in water, while barefoot, or when hands or feet are wet. Always keep the generator dry. Never operate generator in rain or under wet conditions. Use a ground fault circuit interrupter (GFCI) in a damp or highly conductive area, such as metal decking or steel work. Never plug electronic devices into generator having frayed, worn, or bare wires. Never touch bare wires or make contact with receptacles. generator at all times. If using the generator for back up power, notify the utility company. install a transfer switch. Failure to isolate the generator from the power utility could result in serious injury or death to electric utility workers. Generator must be properly grounded to prevent electrocution. Only operate generator on a level surface. Always connect the nut and ground terminal on the frame to an appropriate ground source. Never modify this unit in any way or modify governed speed. Increasing governing speed is dangerous which can result in personal injury and / or damaged equipment. Decreasing governing speed adds an excessive load and can damage equipment. Only when operating at the preset governing speed will this generator supply the correct rated frequency and voltage. Only use this unit as it is intended or serious injury or death could result. Do not bypass any safety device. Moving parts are covered with guards. Make sure all protective covers are in place. Never transport or make adjustments to this unit while it is running. Never insert objects through cooling slots. Never operate this unit if there are any broken or missing parts and only use our Improper treatment of generator can damage the unit and shorten its life. service center. PROP 65 WARNING: This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm. 6

7 FEATURES A B E F G C H D I S O N P Q A - Spark Plug Cover B - Spark Arrestor D - Outer Casing (Side Panel) E - Handle (Grip) F - Air Vent G - Fuel Cap H - Recoil Starter I - Control Panel J - Oil Warning Light K - Overload Indicator Light L - AC Pilot Light M - 3 in 1 Start Switch (RUN / OFF and Choke) N - Economy Switch O - USB Outlet 5VDC 1.5A P - AC Outlet 7 Q - Parallel Outlets R - Ground Terminal S - 12V DC Port

8 CONTROL PANEL FUNCTIONS ON/OFF Start Switch and Choke Start Switch OFF When the Start Switch is in the OFF position the fuel valve is switched off and the engine will not run. Start Switch CHOKE When the Start Switch is in the CHOKE position the fuel valve is switched on and the engine can be started. Start Switch ON When the Start Switch is in the ON position the fuel valve is switched on and the engine can run., Note: The Choke is not required to start a warm engine Oil Warning Indicator Light When the oil falls below the minimum level, the oil warning indicator light comes on and the engine stops automatically. The engine will not Note: If the oil warning indicator light does not come on and the engine stalls, turn the Start Switch to ON and pull the recoil starter. Engine Overload Indicator Light, If the engine overload indicator light comes on, the generator s wattage / amperage capacity has been exceeded by connected electrical devices or by a power surge. When this occurs, the green AC Pilot Indicator Light will go off. The engine will continue to run, but the red Engine Overload Indicator Light will stay on and power will no longer be supplied to connected electronic devices. Oil Warning Indicator Overload Indicator AC Pilot Indicator How to Correct 1. Disconnect any electronic devices then stop the engine. 2. Reduce the total wattage of connected electronic devices until it is within the generator s rated output. 3. Inspect the Air Inlet and Control Panel for any blockage. Remove blockage if found. 4. Restart Engine. Note: The engine overload indicator light may turn on for a few seconds when attaching a load due to a power surge. This is normal. Oil Warning Indicator Overload Indicator AC Pilot Indicator 8

9 CONTROL PANEL FUNCTIONS AC Pilot Indicator Light The green AC Pilot Indicator Light comes on when the engine starts and generates power. Oil Warning Indicator Overload Indicator AC Pilot Indicator DC Circuit Breaker When the DC Circuit Breaker is in the ON position, the generator is able to supply power to connected electronic devices. When the DC Circuit Breaker is in the OFF position, the generator will no longer supply power. The DC Circuit Breaker automatically turns OFF when connecting electronic devices to the generator that exceed the generator s rated output. If the DC Circuit Breaker turns off, reduce the load of connected electronic devices until the load is within the specified rated output. To re-establish power, return the DC Circuit Breaker back to the ON position. CAUTION! If the DC Circuit Breaker turns off again, stop using the generator immediately and consult our dealers. Engine ECO Control When the Engine ECO switch is turned to the ON position, the economy control unit automatically determines the generator s proper engine speed based on the connected electronic load. This results in superior fuel economy and reduces noise. When the ECO switch is turned to the OFF position, the engine runs at the rated speed of 4,850 r/min. Note: The ECO switch must be turned to the OFF position when using electronic devices that require a large starting current, such as a compressor. Parallel Outlets Located just above the Ground Terminal, the generator s Parallel Outlets enable a user to run two D2200iS generator s simultaneously. This operation requires special cables. When operating parallel generators, the rated output is 3.4kVA and the rated current is 28A/120V. For cables and instructions consult a dealer for a PARALLEL OPERATION CABLE KIT. Never connect generators that are different models. Only connect this generator to another D2200iS Standard Generator or D2200iS Companion Generator Only use brands approved parallel operation cable kit to connect generators 9

10 CONTROL PANEL FUNCTIONS Fuel Cap Turn counterclockwise to remove the fuel cap Fuel Cap Air Vent The fuel cap is equipped with an air vent to stop fuel from flowing to the carburetor. The Air Vent must be in the ON position to allow fuel to flow so that the engine can run. Turn the Air Vent to the OFF position to stop fuel flow. ON OFF Ground Terminal The generator s ground terminal must always be used to connect the generator to a driven ground rod. Connect the ground terminal to the driven ground rod with a No 8 AWG (American Wire Gage) copper wire. The wire connects to the terminal between the lock washer and nut. Tighten the nut securely to ensure good connection. Grounding the generator protects you from electric shock that results from a build up of static electricity or undetected ground faults. Generator must be properly grounded to prevent electrocution. Only operate generator on a level surface. Always connect the nut and ground terminal on the frame to an appropriate ground source. 10

11 ASSEMBLY Connecting Generator to an Electrical System If connecting generator to a building s electrical system for standby power, The power from the generator must be isolated from the circuit breaker or alternative power source. The connection must comply with all electrical codes and applicable laws. UNPLUG Never directly connect generator to a household power source. This generator produces a very high voltage which could result in burn or electrocution causing serious injury or death. Never handle the generator, electronic devices, or any cord while standing in water, while barefoot, or when hands or feet are wet. Always keep the generator dry. Never operate generator in rain or under wet conditions. Use a ground fault circuit interrupter (GFCI) in a damp or highly conductive area, such as metal decking or steel work. Never plug electronic devices into generator having frayed, worn, or bare wires. Never touch bare wires or make contact with receptacles. generator at all times. If using the generator for back up power, notify the utility company. install a transfer switch. Failure to isolate the generator from the power utility could result in serious injury or death to electric utility workers. Adding Fuel Set generator on a clean and level surface in an area that is well ventilated. Remove fuel cap. Insert a funnel into the fuel tank and carefully pour gasoline into the tank until fuel level reaches about 1 ½ inches below the top of the neck. Be careful not to overfill the tank to provide space for fuel expansion. Replace fuel cap and secure tightly. ON OFF Turn cap counterclockwise to remove. Do not smoke when adding fuel. provide space for fuel expansion. 11

12 ASSEMBLY Place generator on a level surface. Remove screws and then remove the outer casing cover.(you must remove the spark plug cover to push the side panel off from the inside). Remove the crankcase dipstick. Insert a funnel into the crankcase dipstick hole and carefully add the specified amount of 4-Cycle engine oil (SAE 10W- 30) to empty reservoir until or oil reaches the outer edge of the oil fill hole (crankcase dipstick hole). Be sure to replace dipstick and securely tighten before attempting to start the engine. To check oil, set generator on a level surface, wipe dipstick clean, then reinsert dipstick without re-threading. Recommended Oil: SAE 10W-30 Oil Capacity: 0.35L (11.8oz) CAUTION! generator. Always check oil level before each operation. 12

13 OPERATION Grounding the Generator To avoid electrocution, this generator must be properly grounded prior to use. For instructions see Control Panel Functions pg. 10. Standard Atmospheric Conditions Ambient Temperature: 77ºF (25ºC) Barometric Pressure: 100kPa Relative Humidity: 30% Generator output will vary due to changes in temperature, altitude, and humidity. If the temperature, humidity, or altitude are higher than standard atmospheric conditions, the generator s output will be reduced. The load attached to the generator must therefore be reduced. How to Start Engine Place generator on a level surface. All electrical loads MUST be disconnected from generator. Turn the ECO switch to OFF Turn the Air Vent to the ON position. Turn the 3 in 1 Start Switch to CHOKE Pull recoil handle (starter cord) slowly until resistance is felt, then pull rapidly. Let engine run for several seconds and then gradually, as engine warms up, turn the 3 in 1 Start Switch to the ON position. OFF OFF ON ON Pull cord recoils rapidly and pulls arm towards engine faster than you can let go which could result in injury. To avoid recoil, pull starter cord slowly until resistance is felt, then pull rapidly. Note: To start the generator with the ECO switch in the ON position Disconnect all electrical loads from generator. If ambient temperature is below 32ºF (0ºC) allow 3 minutes for the engine to warm up. The ECO is in ON position, the unit returns to normal operation after the above warm up time. ECO switch must be turned to the OFF position when using electronic devices that require a large starting current, such as a compressor. 13

14 OPERATION How to Stop Engine Turn the ECO switch to the OFF position. Disconnect any electronic device. All loads MUST be disconnect from the generator. Never start or stop the engine with electrical devices plugged in to the receptacles. Turn the 3 in 1 Start Switch to the OFF position. Turn the Air Vent to the OFF position. OFF ON ON OFF Never start or stop engine with electrical devices plugged in to the receptacles. Failure to do so could damage the generator and / or connected electrical devices. Always start the engine and let it stabilize before connecting any electronic devices. Disconnect all electronic devices before stopping the engine. How to Attach Electronic Devices 1. Before Starting generator Make sure the generator is grounded (see page 10 for instructions). Make sure the attached load is within the generator rated output and the receptacle s rated current. Make sure all electrical cords and receptacles are in good condition. Make sure all electronic devices are turned OFF before plugging them into the generator. 2. Start engine 3. If the attached load is small, turn the ECO switch to the ON position. For a larger load, or if attaching multiple electronic devices turn the ECO switch to the OFF position. 4. Make sure the green AC pilot indicator light is on.. 6. Allow generator output to stabilize (engine and attached devices run evenly) before plugging in the next load. 14

15 OPERATION Charging a 12 Volt Battery This generator can be used to charge a 12 volt automotive or storage battery by taking the following steps: ONLY level is low. Never add tap water. 1. Use a wire brush to clean battery terminals if corroded. 2. Before connecting battery to generator, start generator engine. Make sure the DC Protector is turned to the ON position. 3. Securely connect the red cable clamp to the positive (+) battery terminal. 4. Securely connect the black cable clamp to the negative (-) battery terminal. 5. Turn the ESC switch to the OFF position to start battery charging. 6. and 1.28 when measured by a hydrometer. Note: It is strongly recommended to check the gravity level of the electrode at least once per hour with a hydrometer to prevent overcharging and to test the battery s condition. Be careful to follow the hydrometer manufacture s instruction. Battery electrolyte is poisonous and dangerous. Do not disconnect battery clamps while charging. Batteries produce explosive gasses. Disconnecting the battery clamps while charging could spark and ignite. Do not charge battery in an enclosed area. Never smoke while charging the battery or operating or fueling this generator. Battery electrolyte contains sulfuric acid. Avoid contact with skin, eyes, and clothing. Always wear eye protection when charging battery. get immediate medical attention. For internal ingestion, drink large quantities of water or milk, followed by milk of magnesia, beaten egg, or vegetable oil. Contact a medical physician immediately. 15

16 OPERATION AC Parallel Operation The 2200I generator has two models that are compatible with each other (Standard and Companion). It is possible to connect two 2200I generators to each other, using a parallel cable kit. Connect PARALLEL OPERATION CABLES to two 2200I generators according to the instructions provided with the cable kit. Make sure the ECO switch is in the same position on both generators. All electronic devices should be turned OFF and disconnected from generators prior to starting generator engines. Start generator engines. Make sure the green output indicator light comes on for each generator. Allow generator output to stabilize (engine and attached devices run evenly) before plugging in the next load. Parallel Box Maximum Power in Parallel Operation: 4.4kVA Rated Power in Parallel Operation: 3.4kVA For continuous operation, do not exceed the rated output. Note: It is strongly recommended to plug in devices with the overloading the generator. Note: Most electronic devices require power beyond its rated wattage to start. This additional power is referred to as surge watts and usually lasts between 2-3 seconds. When an electronic device is started, the red overload indicator may come on. This is normal. If the light stays on disconnect all electronic devices and stop the engine. Refer to Engine Overload Indicator Light on page 8. Only connect electronic devices to the generator that are in good working order and do not exceed the rated power supply of the parallel generators or the desired receptacle. A faulty appliance or power cord can create an electric shock. Do not use electronic devices that have a damaged cord or plug. If an appliance begins to operate abnormally, becomes sluggish, or stalls, turn off and disconnect appliance immediately. The appliance may have a fault or its rated load capacity exceeds the power supply of the generator. To avoid damage to generator or electronic device, do not connect a load to the generator if its electrical rating exceeds that of the receptacle. Never connect generators that are different models. Only connect this generator to another 2200I Generator or 2200I Companion Generator Only use brands approved parallel operation cable kit to connect generators. The parallel cable must be removed if operating only one generator. Never disconnect or remove the parallel operation cable while generator is still running. 16

17 OPERATION Don t Overload Generator Make sure you can supply enough rated watts for all electronic devices connected to the generator. Rated watts refer to the power a generator must supply to keep a device running. Surge watts refer to the power a generator must supply to start an electronic device. This power surge for starting a device usually lasts between 2-3 seconds but this additional output must be taken into account when selecting the electronic devices you plan to attach to the generator. To prevent overloading the generator take the following steps: 1. Add up the total rated wattage of all electronic devices that will be connected to the generator simultaneously. 2. Estimate surge watts by adding the item(s) with the highest output (it is unnecessary to calculate the surge output for all devices as they should be connected one at a time). 3. Add the Surge Watts to the total Rated Watts in step 1. Keep total load within generator s power capacity. Wattage Reference Guide (Wattages listed are just approximations. Check electronic device for actual wattage) Essentials Rated Watts Surge Watts 75W Light Bulbs 75 each 75 each 18 CU Ft Refrigerator / Freezer Furnace Fan (⅓ HP) Sump Pump (⅓ HP) Water Pump (⅓ HP) Heating/Cooling Table Fan Electric Blanket Space Heater Kitchen Blender Toaster (2 slice) Coffee Maker Electric Range (1 element) Dishwasher Laundry Room Iron Washing Machine Gas Clothes Dryer Bathroom Rated Watts Surge Watts Hair Dryer Curling Iron Family Room X-Box or Play Station 40 0 AM/FM Radio VCR Color TV (27 ) Fax Machine 65 0 Personal Computer (17 Monitor) Laser Printer Copy Machine Power Tools 1000W Quartz Halogen Work Light Airless Sprayer (⅓ HP) Reciprocity Saw Circular Saw (7 ¼ ) Mitar Saw (10 ) Table/Radial Arm Saw Electric Drill (½ HP, 5.4 Amps)

18 MAINTENANCE Regular maintenance will extend the life of this generator and improve its performance. The warranty does not cover items that result from operator negligence, misuse, or abuse. To receive full value from the warranty, operator must maintain the generator as instructed in this manual, including proper storage. Before inspecting or servicing this machine, make sure the engine is off and no parts are moving. Disconnect the spark plug wire and move it away from the spark plug. CAUTION! If you are unsure of how to perform a maintenance task, have the unit serviced by our dealers. CAUTION! Only use our spedified replacement parts. Maintenance Schedule Pre-Operation Steps Before starting the engine, perform the following pre-operation steps: Check the level of the engine oil and the fuel tank level. Check for any leakage. Check fuel hose for cracks or damage. Replace if necessary. pick up loose debris. If dirt is caked on, use a soft bristle brush. Inspect the work area for hazards. After Each Use Follow the following procedure after each use: Shut off engine. Store unit in a clean and dry area. After First 5 Hours Change Oil. After 8 Hours or Daily Clean Debris. Check Engine Oil Level. 6 Months (100 hr Use) Check and Clean Air Filter Element. (Service more often under wet or dusty conditions.) Change Engine Oil. (Service more often under dirty or dusty conditions.) Service Spark Plug. 12 Months (300 hr Use) Clean Fuel Filter. Replace if necessary. Check Crankcase Breather Hose for cracks or damage. Replace if necessary. De-carbonize cylinder head. See dealer. Check and adjust Valve Clearance. See dealer. Check all Fittings and Fasteners. See dealer. 18

19 MAINTENANCE Checking Spark Plug Remove cap. Then remove spark plug cap. Disconnect the spark plug wire from the spark plug. Before removing the spark plug, clean the area around its base to prevent debris from entering the engine. Insert a spark plug socket wrench through the opening on the outside of the cover. Turn the wrench counterclockwise. Check for discoloration and clean carbon deposits off the electrode with a wire brush. Check the electrode gap and slowly adjust to mm ( in) if necessary. Reinstall spark plug and tighten to Torque 20.0Nm (14.8ft-lb). If spark plug is worn replace only with an equivalent replacement part. Spark plug should be replaced annually. Reconnect spark plug wire. Replace spark plug cap, then replace cap mm Standard Spark Plug: E6TC/E6RT/BPR6HS Spark Plug Gap: mm ( in) Spark Plug Torque: 20.0Nm (14.8ft-lb) Carburetor Adjustment The carburetor is low emission and is equipped with a non-adjustable idle mixture valve. If adjustment is needed contact an authorized dealer. 19

20 MAINTENANCE Changing Oil Place generator on a level surface. Run the generator for several minutes until the engine is warm. Turn off generator. Remove screws, then remove outer casing. Remove the crankcase dipstick. Place an oil pan underneath the engine. Tilt generator to collect used oil. Allow oil to drain completely. Return generator to a level surface. (Crankcase Dipstick hole). Use a clean rag to wipe up any spilled oil. Replace crankcase dipstick. Reinstall outer casing and tighten screws. Recommended Engine Oil: SAE 10W-30 Recommended Engine Oil Grade: API Service SE type or higher quality of engine oil. Engine Oil Quantity: 0.35L (11.8oz) CAUTION! the engine. CAUTION! Make sure no foreign matter enters the crankcase 20

21 MAINTENANCE Air Filter To clean, remove the screws then remove outer casing. Remove the foam element. Wash the foam element in solvent and let dry. Pour a small amount of oil on the foam element then squeeze out, but do not wring out, excess oil. Foam element should be damp, but not dripping. CAUTION! Do not run the generator without reinstalling the foam element or excessive piston and cylinder wear may result. Check the muffler screen and spark arrester for damage.if damaged replace with Our replacement parts Install the outer casing and tighten the screws. Remove screws, then remove shown area of outer casing. Avoid contacting hot areas of this unit. Allow hot components to cool before touching. 21.

22 MAINTENANCE Fuel Tank Filter Install fuel cap. Fuel Filter To clean, remove screws, remove outer casing, and drain fuel. Lift and hold onto the clamp, then remove hose from tank. Install hose and clamp. Open fuel valve. Inspect for leakage. Install outer casing and tighten screws. Storage To protect your generator from deterioration during long term storage, take the following preventative measures: EXTERIOR pick up loose debris. If dirt is caked on, use a soft bristle brush. Inspect air cooling slots. Remove any debris if obstructed. Store indoors and use a protective cover to protect from dust. FUEL For short-term storage, add fuel stabilizer to prevent stale fuel from causing acid and gum deposits in the fuel system and carburetor. For long-term storage, drain the fuel. ENGINE Remove spark plug. Pour about 1 TBL of SAE 10W-30 engine oil into the spark plug hole, then reinstall spark plug. With the 3 in 1 switch in the OFF position, pull the recoil starter several times to coat cylinder walls with oil. Slowly pull the recoil starter until you feel the engine build compression (when you feel resistance). Leave the engine in this state. This will help prevent rust build up in the cylinder walls. 22

23 MAINTENANCE How to drain fuel Turn the 3 in 1 switch to the OFF position. Use a siphon to transfer gasoline from generator into a gasoline approved container. Wipe up any spilled fuel with a clean rag. Start generator engine and let it run until it stops and all remaining fuel is consumed. Do not connect electronic devices to generator during this process. Remove outer casing screws, then remove outer casing.. Turn the 3 in 1 switch to OFF Tighten the drain screw. Install the outer casing and tighten screws. When the engine has completely cooled down, turn the Fuel Cap Air Vent to the OFF position. 23

24 TROUBLESHOOTING Problem Cause Solution Generator is running, but does not supply power. Engine runs good without load but bogs down when loads are connected Engine will not start, shuts down during operation, or starts and runs rough. 1. DC Circuit Breaker is OFF 2. Green AC Pilot Light Indicator is off. 3. Poor connection 4. Defective cord set 5. Connected device is faulty 6. Fault in generator 1. Short circuit in connected device 2. Generator is overloaded 4. Engine speed is too slow 5. Short circuit in generator 1. 3 in 1 switch set to OFF 1. Turn DC Circuit Breaker ON 2. Stop engine and restart. 3. Check and repair 4. Check and repair 5. Connect a device that is working properly 6. Contact service department 1. Disconnect device 2. See pg 17 Don t overload generator 4. Contact service department 5. Contact service department 1. Turn switch to CHOKE then pull recoil starter. Engine lacks power Engine hunts or falters 4. Out of fuel or Stale fuel 5. Spark plug wire disconnected from spark plug 6. Bad spark plug 7. Water in fuel 8. Overchocking 9. Low oil level 11. Faulty ignition 1. Generator is overloaded 4. Engine needs servicing 1. Choke was removed too soon 3. Carburetor is running too rich or too lean 4. Replace fuel 5. Reconnect spark plug wire 6. Clean or replace spark plug 7. Drain fuel tank and replace fuel 8. Turn off choke 9. Add oil level. 10. Wait 5 minutes and recrank engine 11. Contact our dealer 1. See pg 17 Don t overload generator 4. Contact service department 1. Move to choke until engine runs evenly 3. Contact service department 24

25 DIAGRAMS Generator Engine Generator Set Model No. 2200I Type Inverter Rated Frequency 60Hz Rated Voltage 120V Maximum Output Power 2.2kW Rated Output Power 1.7kW Power Factor 1.0 AC Output Quality ISO8528 G1 THD 3% Noise Level 58-60dBA DC Output 12V/8A DC Non-Fuse Protector Overload Frequency Regulator Overload Protect AC Protection Process Control Engine DH80i Engine Type Single Cylinder, 4-Stroke, Forced Air Cooling, OHV Displacement 80cc Fuel Type Unleaded Gasoline Fuel Tank Capacity 4.5L Continued Running Time (At Rated Power) 4h Fuel Tank Capacity 350ml Spark Plug Model No. E6TC/E6RTC Starting Mode Recoil Starter Length Width Height mm Net Weight 21kg 25

26 WIRING DIAGRAM W W! P /1