Modeling and Identification of a Mechatronic Exhaust Gas Recirculation Actuator of an Internal Combustion Engine

Size: px
Start display at page:

Download "Modeling and Identification of a Mechatronic Exhaust Gas Recirculation Actuator of an Internal Combustion Engine"

Transcription

1 21 American Control Conference Marriott Waterfront, Baltimore, MD, USA June 3-July 2, 21 WeC19.5 Modeling and Identification of a Mechatronic Exhaust Gas Recirculation Actuator of an Internal Combustion Engine S. Laghrouche, F. S. Ahmed, M. El Bagdouri, M. Wack, J. Gaber, M. Becherif Laboratoire Systèmes et Transports, Université de Technologie de Belfort-Montbéliard, 9 Belfort, France. Abstract This paper addresses the physical modeling and identification of an EGR Actuator. The EGR actuator has a nonlinear behavior due to its mechanical construction and different friction forces. A nonlinear physical model for an EGR actuator manufactured by Valeo is presented here. Special focus has been given to modeling frictions with the Dahl Model. Different parts of the actuator and friction have been identified. Comparison between simulation and experimental results shows the effectiveness of the proposed model. The model can act as a reference to characterize different designs and future control strategies. Index terms EGR Actuator; Modeling; Automotive Control; Torque Motor; Cam; Friction; Dahl. 1. INTRODUCTION Future regulations regarding NO X and particulate matter emissions would force manufacturers to seek in-cylinder strategies to reduce these emissions along with aftertreatment devices [1]. motor and valve [4, 6]. Friction, present in the mechanical parts of the actuator, plays a significant part in the nonlinear behavior [4, 5]. An accurate and reliable model of a mechatronic EGR actuator for control purposes requires that these non linearities be incorporated [6]. This paper is aimed at providing a complete physical model using a commercial EGR actuator manufactured by Valeo (figure 1) and identifying its parameters. The primary purpose is to understand and simulate actuator dynamics, which are often neglected in global engine control. This model can also serve as a general characterization of mechatronic EGR valves in order to identify new valves and to design control systems around them, using this methodology. Exhaust Gas Recirculation (EGR) is one of the most effective techniques for reducing NO X emissions in internal combustion engines (ICE) [1,2]. This technique is applied using a control actuator that recirculates the exhaust gas given out by the engine, adding it to the fresh fuel-air mixture at the intake. The addition of inert gases to the intake mixture reduces peak burned gas temperatures and hence, reduces NO X formation rates while improving fuel consumption [2]. Precise and accurate modeling and control of the EGR actuator is essential to the system since, while improving fuel consumption, the low temperature reduces combustion rate and makes stable combustion difficult to achieve. EGR percentages in 15 to 3% range are the maximum that an SI engine would tolerate [2], while EGR has to be cut off completely during ignition and idling. An ideal control strategy would be expected to correlate EGR rate with NO X generation [3]. Older vacuum EGR Valves are now losing their popularity in favor of fast and efficient mechatronic actuators that are controlled using DC or Brushless DC (BLDC) motors [2]. These actuators allow faster response times and accuracy in transient conditions. Mechatronic valves pose problems in control because of nonlinearities [4, 5, 6, 7, 9]. These nonlinearities arise from several sources such as temperature transients, external perturbations, and aero-load dynamics. Another possible source is a nonlinear transmission between the actuator Figure 1: Valeo EGR Actuator connected to the experimental setup This paper is organized in the following manner. Section 2 deals with overview of the actuator under study and its modeling. Section 3, is dedicated to dynamic friction modeling. In section 4, the experimental setup is discussed and the parameters of the complete model are identified. Model validation is discussed in section 5 while in section 6, some conclusions are presented. 2. DESCRIPTION OF THE EGR ACTUATOR 2.1 Overview Figure 2 shows that the Valeo EGR actuator splits easily into two parts, the motor assembly, containing the motor, spring and position sensor, and the mechanical assembly containing the valve /1/$ AACC 2242

2 Figure 4: Cam (Rot-Lin Transmission) Figure 2: Valeo EGR Actuator with Motor and Mechanical Assemblies being separated The shaft inside the cavity of the mechanical assembly is installed in a variable height groove, which is carved into the sides of the cavity, and thus moves up or down when rotated about the axis of the casing (figure. 3, 4). The shaft fitted with bearings at the ends, sits in the grooves. This assembly forms the cam. The cam is connected to the valve plate below: In order to model the cam to find a relation between the angle and the linear displacement, the valve position was carefully measured at different angles (using the experimental setup described in section 4.1). The curves shown in figure 5 show the relationships obtained between the angle, the sensor voltage and the cam position. Since the sensor voltage is the only quantity that can be measured directly, the mechanical assembly was modeled as the valve linear position, L with respect to the sensor voltage u. Using classical curve fitting this curve of the cam was found to correspond to the following function: Figure 3: Simplified Mechanical Diagram As the cam rotates, it pushes the valve plate down. The coupling between the cam and the motor holds the shaft between its prongs. (a) The deep grooves of the prongs allow for the vertical movement of the shaft. The actuator is spring-loaded, so that it remains shut when no power is applied to the input. The spring returns the cam to its highest point. 2.2 Mechanical Assembly Modeling The cam converts the angular rotation of the motor into linear displacement of the valve. It allows angular motion of about 62 and linear displacement of 6mm. The linear displacement is not proportional to the rotation. The nonlinear response is evident in the sketch in figure. 4. (b) Figure 5: (a) Angle vs. Position Sensor Voltage, (b) Angle vs. Valve Position 2243

3 2.3 Motor Assembly Modeling The motor used in this actuator is a torque motor that has a limited rotation of 8, further reduced to 6 due to the limitation of the cam. Since the motor angle has a linear relationship with the position sensor output up to 6, this system is modeled directly in terms of angular position. While the torque of a torque motor is a function of its angular position, the characteristic curve in figure 6 shows that the mechanical limits of the motor ensure its operation in the constant torque region. Hence it can be modeled in the same way as a DC motor. The motor s rotation is countered by a spring, housed inside the motor casing. This motorspring system allows the motor shaft to have the following dynamics [4, 9]: Motor Position (Deg ) EGR Valve Static Characteristics Input PWM (%Duty Cycle) 5 Figure 6: EGR Actuator Characteristic Curve 2 Here, θ is the angular position of the motor; K a and E a are the motor constant and the back EMF respectively, while R a and L a are motor resistance and inductance. J tot represents the total moment of inertia of the system while ω is the angular velocity. The transitory current can be neglected since the mechanical time constant is always much greater than the electrical time constant [4, 6]. T f is the friction force, a dynamic identity in itself. T o is the spring precompression torque working against the motor before it starts to move. K spr is the spring constant. Putting all values in the dynamic model results in the following relationship: 3. FRICTION A characteristic feature of the actuator, prominent in figure 6 is the hysteresis between the opening and closing paths of the actuator. This hysteresis is due to friction [4, 8]. Friction can be divided into two components, the static part which is needs to be overcome to start the relative motion between two surfaces and dynamic part which is parallel to the surfaces and always opposite to the direction of motion [5, 8] Dynamic friction comprises of two parameters, dry friction, also called Coulomb Friction and viscous friction which comes through addition of lubricants [8]. When a body starts from zero velocity, i.e. breaks away from static friction, the transition between static and dynamic friction is called Stribeck effect [8, 9]. This effect can be understood in figure. 7; which shows two friction models, with and without Stribeck effect. The friction force, T f is modeled in the next section, while the pre-compression, T o is constant and must be overcome by the motor before the shaft starts to move. is defined as the voltage required to overcome T o and T f. The remaining would hence result in actuator motion. Therefore the motor and spring dynamics can be modeled completely as Considering initial conditions to be zero, the Laplace transform of the system comes out to be: Figure 7: (a) Static friction + Coulomb friction (b) Viscous Friction added (c) Stribeck Effect added The Dahl friction model considers friction to arise from the asperities or irregularities of surfaces in contact. It hence models the asperities as microscopic springs [8, 9], which hold the surfaces in place until their elastic limit is exceeded. Hence this model allows for coulomb and viscous friction modeling. This is effective for ball bearings since the value of static and coulomb friction are very near. This model has been used here to identify the dynamic friction working in the EGR valve. Dahl s model [8, 9] mimics the stress-strain curve in classic solid mechanics [9]. It is the simplest of all dynamic models, for example, LuGre etc. since it has the minimum parameters of all dynamic friction models. If x is the displacement, F is the friction force F ; the Dahl model has the form [9] 2244

4 Where, σ is the stiffness coefficient and α is a parameter defining the shape of the stress strain curve. A value higher than 1 results in sharper bends. actuator was tested at no load, it went from closed to full open position by varying the duty-cycle from % to 18%. The armature voltage, V a is the average on-time of the PWM pulse per second. 4.2 Motor-Spring Identification Figure 1 represents the complete block diagram of our model of the EGR motor. Figure 8: Characteristic curve of Dahl Model As seen in figure. 8, the Dahl model relates friction to position. If we consider the Dahl model with respect to time, the model becomes: Figure 1: Block Diagram of EGR Actuator Model The value of armature resistance R a can be measured experimentally at stationary positions through Ohm s Law i.e. by measuring current at different voltages where the rotor is either locked or at a stationary position. Voltage divided by current would give us the armature resistance. Where, v is the velocity. The parameters can be found easily once the curve is known. 4. EXPERIMENTS AND PARAMETER IDENTIFICATION Figure 11: Actuator Characteristic Curve (simplified) Figure 9: Experimental Setup The experiments were conducted using National Instruments CompactRIO system, as shown in figure 9. The actuator motor was powered through PWM. A square wave of 1 khz, with an amplitude of V s = 15V is given to the motor and the average power is varied by varying the duty-cycle. Since the With figure 11 as a reference, we define D PC as the dutycycle leading to countering the spring pre-compression, D s as the amount countering the static friction. The value of static friction and spring pre-compression torque can directly be calculated from the graph. The effective duty-cycle and armature voltage then become: 2245

5 for all positive values of D a and for the rest. V s is the maximum applied voltage. measured values, θ taken at the same armature voltages same as the estimation. The vector β estimate is then obtained by solving the following least squares problem through a nonlinear minimization algorithm The algorithm was implemented in Matlab and it provided the following results: R a = 3.75Ω K a = 19.6mN.m/A K spr =45.97 mn.m/rad J tot = 1.3e -7 Kg.m 2 Figure 12: EGR ActuatorStep Response The value of T o can be calculated from the characteristic curve graph, since we know that the motor torque T m equals T o at 5% PWM. Using the relationship motor torque relationship, Using the motor-spring dynamics from section 2.3 This transfer function can be compared to the general form of a second order system, 4.3 Dynamic Friction Identification The ease of using the Dahl model is that it considers static friction and coulomb friction to be equal. Hence only two parameters are to be identified, F c and σ. Now the Dahl model would be used to identify the parameters of the dynamic friction. Recalling from section 2.3: Our model parameters can be found out using the generic second order step response form. The experimental step response in figure 12 shows the system response to be overdamped. Hence the generic form would be: All other parameters except T f have been determined. In order to reach the characteristic curve of the Dahl Model, all other components except T f were subtracted. From here, the value of σ and F c was found to be: F c = mN.m σ =.5x1-3 The values of the unknown parameters (K a, K spr, J tot ) through the standard Least Squares procedure using any non linear minimization function. An estimation vector, β=[ K a, K spr, J tot ] is defined for the estimation algorithm, which evaluates the model on the vector : 5. MODEL VALIDATION While NI LabVIEW was used for experiments and data acquisition, the identification and modeling procedures were performed on Matlab. The model was simulated and the results were compared with data obtained from experiments. The correspondence between measured and calculated angles was considered for verification, since the actuator does not have any direct means for measuring the linear, cam guided movement of the valve plate. In figure 13, the graphs show the experimentally obtained curves with simulated ones. It can be seen that the results corroborate well with the experimental data. Where Va represents the armature voltage values on which the model is evaluated. This model is compared to a set of 2246

6 (a) (b) Figure 13: Experimental Values vs. Model Estimated Values (a) Static Characteristics (b) Dynamic Characteristics 6. CONCLUSION A commercial EGR actuator has been modeled and its electrical and mechanical parameters have been successfully identified. In addition, friction forces acting on the actuator have also been dynamically modeled. The results of validation have been successful. [3]. M. Zheng, G. T. Reader; J. G. Hawley, Diesel engine exhaust gas recirculation, a review on advanced and novel concepts Energy Conversion and Management (24). [4]. R. Scattolini, C. Siviero, M. Mazzucco, S. Ricci, L. Poggio and C. Rossi, Modeling and Identification of an Electromechanical Internal Combustion Engine Throttle Body Control Eng. Practice Vol. 5. No.9. pp (1997). [5]. F. Contreras, I. P. Quiroz, C. C. dewit, Further Results on Modeling and Identification of an Electronic Throttle Body Proc. 1 th Mediterranean Conf. on Control and Automation-MED (July, 22). [6]. J. B. Song, K. S. Byun, Throttle Actuator Control System for Vehicle Traction Control Mechatronics (1999). [7]. C. Rossi, A. Tilli, A. Tonielli Robust Control of a Throttle Body for Drive by Wire Operation of Automotive Engines, IEEE Trans. Control Systems Technology Vol. 8 (6 November 2). [8]. D. Pavkovic, J. Deur, M. Jansznn N. Peric, Adaptive Control of Automotive electronic Throttle Control Engineering Practice (26). [9]. H. Olsson, K.J. Åström, C. Canudas de Wit., M. Gäfvert, P. Lischinsky, Friction Models and Friction Compensation European Journal of Control 4(3) (1998). [1]. T. Tjahjowidodo, F. Al-Bender, H. V. Brussel, Friction Identification and Compensation in a DC Motor IFAC (25). [11]. P. Myszkorowski, F. Altpeter, R. Longchamp, Position Control of Drives with Friction Proc. 38 th Conference on Decision and Control (December 1999). [12]. H. M. Kim, S. H. Park, S. I. Han, Precise friction control for the nonlinear friction system using the friction state observer and sliding mode control with recurrent fuzzy neural networks Mechatronics (29). [13]. B. Borsotto, E. Godoy, D. Beauvois, E. Devaud, An Identification Method for Static and Coulomb Friction Coefficients Int. Jour.Contro, Automation and Systems 7(2) 35:31 (29). [14]. Melexis. MLX9316 Rotary Position Sensor IC Datasheet(27), all_effect/triaxis_hall_ics/mlx9316_566.aspx Future studies would be focused on further improvement in hysteresis and friction modeling. More comprehensive friction models are going to be used (eg. LuGre), to model Stribeck effect and static friction. Actuator tests under load are also in preparation along with tests to observe variations in actuator parameters with temperature. REFERENCES [1]. A. Maiboom, X. Tauzia, J. F. Hétet, Experimental study of various effects of Exhaust Gas Recirculation (EGR) on combustion and emissions of an automotive direct injection diesel engine Energy (28). [2]. G. H. Abd-Alla, Using Exhaust Gas Recirculation in Internal Combustion Engines: A Review, Energy Conversion and Management 43, (22). 2247

Relevant friction effects on walking machines

Relevant friction effects on walking machines Relevant friction effects on walking machines Elena Garcia and Pablo Gonzalez-de-Santos Industrial Automation Institute (CSIC) 28500 Madrid, Spain email: egarcia@iai.csic.es Key words: Legged robots, friction

More information

Modelling of electronic throttle body for position control system development

Modelling of electronic throttle body for position control system development Chapter 4 Modelling of electronic throttle body for position control system development 4.1. INTRODUCTION Based on the driver and other system requirements, the estimated throttle opening angle has to

More information

837. Dynamics of hybrid PM/EM electromagnetic valve in SI engines

837. Dynamics of hybrid PM/EM electromagnetic valve in SI engines 837. Dynamics of hybrid PM/EM electromagnetic valve in SI engines Yaojung Shiao 1, Ly Vinh Dat 2 Department of Vehicle Engineering, National Taipei University of Technology, Taipei, Taiwan, R. O. C. E-mail:

More information

Fuzzy based Adaptive Control of Antilock Braking System

Fuzzy based Adaptive Control of Antilock Braking System Fuzzy based Adaptive Control of Antilock Braking System Ujwal. P Krishna. S M.Tech Mechatronics, Asst. Professor, Mechatronics VIT University, Vellore, India VIT university, Vellore, India Abstract-ABS

More information

A Comprehensive Study on Speed Control of DC Motor with Field and Armature Control R.Soundara Rajan Dy. General Manager, Bharat Dynamics Limited

A Comprehensive Study on Speed Control of DC Motor with Field and Armature Control R.Soundara Rajan Dy. General Manager, Bharat Dynamics Limited RESEARCH ARTICLE OPEN ACCESS A Comprehensive Study on Speed Control of DC Motor with Field and Armature Control R.Soundara Rajan Dy. General Manager, Bharat Dynamics Limited Abstract: The aim of this paper

More information

One-Cycle Average Torque Control of Brushless DC Machine Drive Systems

One-Cycle Average Torque Control of Brushless DC Machine Drive Systems One-Cycle Average Torque Control of Brushless DC Machine Drive Systems Najma P.I. 1, Sakkeer Hussain C.K. 2 P.G. Student, Department of Electrical and Electronics Engineering, MEA Engineering College,

More information

Wind Turbine Emulation Experiment

Wind Turbine Emulation Experiment Wind Turbine Emulation Experiment Aim: Study of static and dynamic characteristics of wind turbine (WT) by emulating the wind turbine behavior by means of a separately-excited DC motor using LabVIEW and

More information

Design & Development of Regenerative Braking System at Rear Axle

Design & Development of Regenerative Braking System at Rear Axle International Journal of Advanced Mechanical Engineering. ISSN 2250-3234 Volume 8, Number 2 (2018), pp. 165-172 Research India Publications http://www.ripublication.com Design & Development of Regenerative

More information

G Prasad 1, Venkateswara Reddy M 2, Dr. P V N Prasad 3, Dr. G Tulasi Ram Das 4

G Prasad 1, Venkateswara Reddy M 2, Dr. P V N Prasad 3, Dr. G Tulasi Ram Das 4 Speed control of Brushless DC motor with DSP controller using Matlab G Prasad 1, Venkateswara Reddy M 2, Dr. P V N Prasad 3, Dr. G Tulasi Ram Das 4 1 Department of Electrical and Electronics Engineering,

More information

INTRODUCTION. I.1 - Historical review.

INTRODUCTION. I.1 - Historical review. INTRODUCTION. I.1 - Historical review. The history of electrical motors goes back as far as 1820, when Hans Christian Oersted discovered the magnetic effect of an electric current. One year later, Michael

More information

Application Information

Application Information Moog Components Group manufactures a comprehensive line of brush-type and brushless motors, as well as brushless controllers. The purpose of this document is to provide a guide for the selection and application

More information

Reduction of Self Induced Vibration in Rotary Stirling Cycle Coolers

Reduction of Self Induced Vibration in Rotary Stirling Cycle Coolers Reduction of Self Induced Vibration in Rotary Stirling Cycle Coolers U. Bin-Nun FLIR Systems Inc. Boston, MA 01862 ABSTRACT Cryocooler self induced vibration is a major consideration in the design of IR

More information

SPEED AND TORQUE CONTROL OF AN INDUCTION MOTOR WITH ANN BASED DTC

SPEED AND TORQUE CONTROL OF AN INDUCTION MOTOR WITH ANN BASED DTC SPEED AND TORQUE CONTROL OF AN INDUCTION MOTOR WITH ANN BASED DTC Fatih Korkmaz Department of Electric-Electronic Engineering, Çankırı Karatekin University, Uluyazı Kampüsü, Çankırı, Turkey ABSTRACT Due

More information

Simulating Rotary Draw Bending and Tube Hydroforming

Simulating Rotary Draw Bending and Tube Hydroforming Abstract: Simulating Rotary Draw Bending and Tube Hydroforming Dilip K Mahanty, Narendran M. Balan Engineering Services Group, Tata Consultancy Services Tube hydroforming is currently an active area of

More information

Design and Control of Lab-Scale Variable Speed Wind Turbine Simulator using DFIG. Seung-Ho Song, Ji-Hoon Im, Hyeong-Jin Choi, Tae-Hyeong Kim

Design and Control of Lab-Scale Variable Speed Wind Turbine Simulator using DFIG. Seung-Ho Song, Ji-Hoon Im, Hyeong-Jin Choi, Tae-Hyeong Kim Design and Control of Lab-Scale Variable Speed Wind Turbine Simulator using DFIG Seung-Ho Song, Ji-Hoon Im, Hyeong-Jin Choi, Tae-Hyeong Kim Dept. of Electrical Engineering Kwangwoon University, Korea Summary

More information

PERFORMANCE AND ENHANCEMENT OF Z-SOURCE INVERTER FED BLDC MOTOR USING SLIDING MODE OBSERVER

PERFORMANCE AND ENHANCEMENT OF Z-SOURCE INVERTER FED BLDC MOTOR USING SLIDING MODE OBSERVER PERFORMANCE AND ENHANCEMENT OF Z-SOURCE INVERTER FED BLDC MOTOR USING SLIDING MODE OBSERVER K.Kalpanadevi 1, Mrs.S.Sivaranjani 2, 1 M.E. Power Systems Engineering, V.S.B.Engineering College, Karur, Tamilnadu,

More information

PERFORMANCE ANALYSIS OF BLDC MOTOR SPEED CONTROL USING PI CONTROLLER

PERFORMANCE ANALYSIS OF BLDC MOTOR SPEED CONTROL USING PI CONTROLLER PERFORMANCE ANALYSIS OF BLDC MOTOR SPEED CONTROL USING PI CONTROLLER Karishma P.Wankhede 1, K. Vadirajacharya 2 1 M.Tech.II Yr, 2 Associate Professor,Electrical Engineering Department Dr. BabasahebAmbedkar

More information

CHAPTER 4 MODELING OF PERMANENT MAGNET SYNCHRONOUS GENERATOR BASED WIND ENERGY CONVERSION SYSTEM

CHAPTER 4 MODELING OF PERMANENT MAGNET SYNCHRONOUS GENERATOR BASED WIND ENERGY CONVERSION SYSTEM 47 CHAPTER 4 MODELING OF PERMANENT MAGNET SYNCHRONOUS GENERATOR BASED WIND ENERGY CONVERSION SYSTEM 4.1 INTRODUCTION Wind energy has been the subject of much recent research and development. The only negative

More information

POWER QUALITY IMPROVEMENT BASED UPQC FOR WIND POWER GENERATION

POWER QUALITY IMPROVEMENT BASED UPQC FOR WIND POWER GENERATION International Journal of Latest Research in Science and Technology Volume 3, Issue 1: Page No.68-74,January-February 2014 http://www.mnkjournals.com/ijlrst.htm ISSN (Online):2278-5299 POWER QUALITY IMPROVEMENT

More information

Understanding the benefits of using a digital valve controller. Mark Buzzell Business Manager, Metso Flow Control

Understanding the benefits of using a digital valve controller. Mark Buzzell Business Manager, Metso Flow Control Understanding the benefits of using a digital valve controller Mark Buzzell Business Manager, Metso Flow Control Evolution of Valve Positioners Digital (Next Generation) Digital (First Generation) Analog

More information

China. Keywords: Electronically controled Braking System, Proportional Relay Valve, Simulation, HIL Test

China. Keywords: Electronically controled Braking System, Proportional Relay Valve, Simulation, HIL Test Applied Mechanics and Materials Online: 2013-10-11 ISSN: 1662-7482, Vol. 437, pp 418-422 doi:10.4028/www.scientific.net/amm.437.418 2013 Trans Tech Publications, Switzerland Simulation and HIL Test for

More information

International Journal of Advance Research in Engineering, Science & Technology

International Journal of Advance Research in Engineering, Science & Technology Impact Factor (SJIF): 4.542 International Journal of Advance Research in Engineering, Science & Technology e-issn: 2393-9877, p-issn: 2394-2444 Volume 4, Issue 4, April-2017 Simulation and Analysis for

More information

Study on the Servo Drive of PM-LSM to Be Used in Parallel Synchronous Drive

Study on the Servo Drive of PM-LSM to Be Used in Parallel Synchronous Drive Journal of Mechanics Engineering and Automation 5 (2015) 580-584 doi: 10.17265/2159-5275/2015.10.007 D DAVID PUBLISHING Study on the Servo Drive of PM-LSM to Be Used in Parallel Synchronous Drive Hiroyuki

More information

Simulation of Voltage Stability Analysis in Induction Machine

Simulation of Voltage Stability Analysis in Induction Machine International Journal of Electronic and Electrical Engineering. ISSN 0974-2174 Volume 6, Number 1 (2013), pp. 1-12 International Research Publication House http://www.irphouse.com Simulation of Voltage

More information

A Simple Approach for Hybrid Transmissions Efficiency

A Simple Approach for Hybrid Transmissions Efficiency A Simple Approach for Hybrid Transmissions Efficiency FRANCESCO BOTTIGLIONE Dipartimento di Meccanica, Matematica e Management Politecnico di Bari Viale Japigia 182, Bari ITALY f.bottiglione@poliba.it

More information

Fuzzy Logic Controller for BLDC Permanent Magnet Motor Drives

Fuzzy Logic Controller for BLDC Permanent Magnet Motor Drives International Journal of Electrical & Computer Sciences IJECS-IJENS Vol: 11 No: 02 12 Fuzzy Logic Controller for BLDC Permanent Magnet Motor Drives Tan Chee Siong, Baharuddin Ismail, Siti Fatimah Siraj,

More information

DESIGN AND EXPERIMENTATION OF TEST RIG TO CHARACTERIZE HYDROSTATIC DRIVEFOR LINEAR ACTUATOR

DESIGN AND EXPERIMENTATION OF TEST RIG TO CHARACTERIZE HYDROSTATIC DRIVEFOR LINEAR ACTUATOR DESIGN AND EXPERIMENTATION OF TEST RIG TO CHARACTERIZE HYDROSTATIC DRIVEFOR LINEAR ACTUATOR Sherif Elbaz 1, Moatasem 2, Ibrahim 3, Nabila 4, Mohamed 5 1 Automotive Engineering Department, Ain-Shames University,

More information

PLUGGING BRAKING FOR ELECTRIC VEHICLES POWERED BY DC MOTOR

PLUGGING BRAKING FOR ELECTRIC VEHICLES POWERED BY DC MOTOR PLUGGING BRAKING FOR ELECTRIC VEHICLES POWERED BY DC MOTOR Nair Rajiv Somrajan 1 and Sreekanth P.K. 2 1 PG Scholar Department of Electrical Engineering, Sree Buddha College of Engineering, Pattoor, Alappuzha

More information

INDUCTION motors are widely used in various industries

INDUCTION motors are widely used in various industries IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 44, NO. 6, DECEMBER 1997 809 Minimum-Time Minimum-Loss Speed Control of Induction Motors Under Field-Oriented Control Jae Ho Chang and Byung Kook Kim,

More information

Generator Speed Control Utilizing Hydraulic Displacement Units in a Constant Pressure Grid for Mobile Electrical Systems

Generator Speed Control Utilizing Hydraulic Displacement Units in a Constant Pressure Grid for Mobile Electrical Systems Group 10 - Mobile Hydraulics Paper 10-5 199 Generator Speed Control Utilizing Hydraulic Displacement Units in a Constant Pressure Grid for Mobile Electrical Systems Thomas Dötschel, Michael Deeken, Dr.-Ing.

More information

Research in hydraulic brake components and operational factors influencing the hysteresis losses

Research in hydraulic brake components and operational factors influencing the hysteresis losses Research in hydraulic brake components and operational factors influencing the hysteresis losses Shreyash Balapure, Shashank James, Prof.Abhijit Getem ¹Student, B.E. Mechanical, GHRCE Nagpur, India, ¹Student,

More information

Research on Skid Control of Small Electric Vehicle (Effect of Velocity Prediction by Observer System)

Research on Skid Control of Small Electric Vehicle (Effect of Velocity Prediction by Observer System) Proc. Schl. Eng. Tokai Univ., Ser. E (17) 15-1 Proc. Schl. Eng. Tokai Univ., Ser. E (17) - Research on Skid Control of Small Electric Vehicle (Effect of Prediction by Observer System) by Sean RITHY *1

More information

DYNAMIC BRAKES FOR DC MOTOR FED ELECTRIC VEHICLES

DYNAMIC BRAKES FOR DC MOTOR FED ELECTRIC VEHICLES DYNAMIC BRAKES FOR DC MOTOR FED ELECTRIC VEHICLES Nair Rajiv Somrajan 1 and Sreekanth P.K 2 1 PG Scholar Department of Electrical Engineering, Sree Buddha College of Engineering, Pattoor, Alappuzh 2 Assistance

More information

CHAPTER 1 INTRODUCTION

CHAPTER 1 INTRODUCTION 1 CHAPTER 1 1.1 Motivation INTRODUCTION Permanent Magnet Brushless DC (PMBLDC) motor is increasingly used in automotive, industrial, and household products because of its high efficiency, high torque,

More information

Preliminary Study on Quantitative Analysis of Steering System Using Hardware-in-the-Loop (HIL) Simulator

Preliminary Study on Quantitative Analysis of Steering System Using Hardware-in-the-Loop (HIL) Simulator TECHNICAL PAPER Preliminary Study on Quantitative Analysis of Steering System Using Hardware-in-the-Loop (HIL) Simulator M. SEGAWA M. HIGASHI One of the objectives in developing simulation methods is to

More information

Application Notes. Calculating Mechanical Power Requirements. P rot = T x W

Application Notes. Calculating Mechanical Power Requirements. P rot = T x W Application Notes Motor Calculations Calculating Mechanical Power Requirements Torque - Speed Curves Numerical Calculation Sample Calculation Thermal Calculations Motor Data Sheet Analysis Search Site

More information

Variable Stiffness Actuators : A General Review

Variable Stiffness Actuators : A General Review Variable Stiffness Actuators : A General Review Mr. S. A. Lavate Dept. of Mechanical Engineering Annasaheb Dange College of Engg. and Technology, Ashta- India Dr. R. G. Todkar Dept. of Mechanical Engineering

More information

Implementation of SMC for BLDC Motor Drive

Implementation of SMC for BLDC Motor Drive Implementation of SMC for BLDC Motor Drive Sanjay M. Patil 1, Swapnil Y. Gadgune 2, MallaReddy Chinala 3 1 Student,Dept. of Electrical Engg FCOER, Sangola, Maharashtra, India 2 Professor Dept. of Electrical

More information

PREDICTION OF PISTON SLAP OF IC ENGINE USING FEA BY VARYING GAS PRESSURE

PREDICTION OF PISTON SLAP OF IC ENGINE USING FEA BY VARYING GAS PRESSURE PREDICTION OF PISTON SLAP OF IC ENGINE USING FEA BY VARYING GAS PRESSURE V. S. Konnur Department of Mechanical Engineering, BLDEA s Engineering College, Bijapur, Karnataka, (India) ABSTRACT The automotive

More information

Performance of DC Motor Supplied From Single Phase AC-DC Rectifier

Performance of DC Motor Supplied From Single Phase AC-DC Rectifier Performance of DC Motor Supplied From Single Phase AC-DC Rectifier Dr Othman A. Alnatheer Energy Research Institute-ENRI King Abdulaziz City for Science and Technology- KACST P O Box 6086, Riyadh 11442,

More information

Design of pneumatic proportional flow valve type 5/3

Design of pneumatic proportional flow valve type 5/3 IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Design of pneumatic proportional flow valve type 5/3 To cite this article: P A Laski et al 2017 IOP Conf. Ser.: Mater. Sci. Eng.

More information

International Journal of Scientific & Engineering Research, Volume 7, Issue 6, June ISSN

International Journal of Scientific & Engineering Research, Volume 7, Issue 6, June ISSN International Journal of Scientific & Engineering Research, Volume 7, Issue 6, June-2016 971 Speed control of Single-Phase induction motor Using Field Oriented Control Eng. Mohammad Zakaria Mohammad, A.Prof.Dr.

More information

Übersicht der VVT-Systementwicklung bei Hilite. Overview of VVT System development at Hilite

Übersicht der VVT-Systementwicklung bei Hilite. Overview of VVT System development at Hilite Übersicht der VVT-Systementwicklung bei Hilite Overview of VVT System development at Hilite M.Sc. Mustafa Mohammed Simulation Engineer Business Unit Engine / Simulation Frei verwendbar Contents Company

More information

SWIRL MEASURING EQUIPMENT FOR DIRECT INJECTION DIESEL ENGINE

SWIRL MEASURING EQUIPMENT FOR DIRECT INJECTION DIESEL ENGINE SWIRL MEASURING EQUIPMENT FOR DIRECT INJECTION DIESEL ENGINE G.S.Gosavi 1, R.B.Solankar 2, A.R.Kori 3, R.B.Chavan 4, S.P.Shinde 5 1,2,3,4,5 Mechanical Engineering Department, Shivaji University, (India)

More information

Using CompactRIO to Build a Virtual Driver of Hybrid Wheeled Vehicle Gabriel Kost 1,a, Andrzej Nierychlok 1,b*

Using CompactRIO to Build a Virtual Driver of Hybrid Wheeled Vehicle Gabriel Kost 1,a, Andrzej Nierychlok 1,b* Solid State Phenomena Online: 2013-03-11 ISSN: 1662-9779, Vol. 198, pp 606-611 doi:10.4028/www.scientific.net/ssp.198.606 2013 Trans Tech Publications, Switzerland Using CompactRIO to Build a Virtual Driver

More information

An Experimental Study of Dual Mass Flywheel on Conventional Flywheel on Two stroke petrol engine.

An Experimental Study of Dual Mass Flywheel on Conventional Flywheel on Two stroke petrol engine. An Experimental Study of Dual Mass Flywheel on Conventional Flywheel on Two stroke petrol engine. N. N. Suryawanshi 1, Prof. D. P. Bhaskar 2 1 M.E. Design, S.R.E.S Kopargaon. nikhil23031992@gmail.com,

More information

THE FKFS 0D/1D-SIMULATION. Concepts studies, engineering services and consulting

THE FKFS 0D/1D-SIMULATION. Concepts studies, engineering services and consulting THE FKFS 0D/1D-SIMULATION Concepts studies, engineering services and consulting r e s e a r c h i n m o t i o n. VEHICLE IN MOTION On the basis of constant engine speeds and loads, the combustion engine

More information

Design and Development of Micro Controller Based Automatic Engine Cooling System

Design and Development of Micro Controller Based Automatic Engine Cooling System International Journal of Engineering Research and Technology. ISSN 0974-3154 Volume 6, Number 6 (2013), pp. 753-558 International Research Publication House http://www.irphouse.com Design and Development

More information

INFLUENCE OF TEMPERATURE ON THE PERFORMANCE TOOTHED BELTS BINDER MAGNETIC

INFLUENCE OF TEMPERATURE ON THE PERFORMANCE TOOTHED BELTS BINDER MAGNETIC INFLUENCE OF TEMPERATURE ON THE PERFORMANCE TOOTHED BELTS BINDER MAGNETIC Merghache Sidi Mohammed, Phd Student Ghernaout Med El-Amine, Doctor in industrial automation University of Tlemcen, ETAP laboratory,

More information

Forced vibration frequency response for a permanent magnetic planetary gear

Forced vibration frequency response for a permanent magnetic planetary gear Forced vibration frequency response for a permanent magnetic planetary gear Xuejun Zhu 1, Xiuhong Hao 2, Minggui Qu 3 1 Hebei Provincial Key Laboratory of Parallel Robot and Mechatronic System, Yanshan

More information

Computer Model for a Parallel Hybrid Electric Vehicle (PHEV) with CVT

Computer Model for a Parallel Hybrid Electric Vehicle (PHEV) with CVT Proceedings of the American Control Conference Chicago, Illinois June 2000 Computer Model for a Parallel Hybrid Electric Vehicle (PHEV) with CVT Barry Powell, Xianjie Zhang, Robert Baraszu Scientific Research

More information

Simulation of Performance Parameters of Spark Ignition Engine for Various Ignition Timings

Simulation of Performance Parameters of Spark Ignition Engine for Various Ignition Timings Research Article International Journal of Current Engineering and Technology ISSN 2277-4106 2013 INPRESSCO. All Rights Reserved. Available at http://inpressco.com/category/ijcet Simulation of Performance

More information

Autonomous Mobile Robot Design

Autonomous Mobile Robot Design Autonomous Mobile Robot Design Topic: Propulsion Systems for Robotics Dr. Kostas Alexis (CSE) Propulsion Systems for Robotics How do I move? Understanding propulsion systems is about knowing how a mobile

More information

Driving Performance Improvement of Independently Operated Electric Vehicle

Driving Performance Improvement of Independently Operated Electric Vehicle EVS27 Barcelona, Spain, November 17-20, 2013 Driving Performance Improvement of Independently Operated Electric Vehicle Jinhyun Park 1, Hyeonwoo Song 1, Yongkwan Lee 1, Sung-Ho Hwang 1 1 School of Mechanical

More information

Collaborative vehicle steering and braking control system research Jiuchao Li, Yu Cui, Guohua Zang

Collaborative vehicle steering and braking control system research Jiuchao Li, Yu Cui, Guohua Zang 4th International Conference on Mechatronics, Materials, Chemistry and Computer Engineering (ICMMCCE 2015) Collaborative vehicle steering and braking control system research Jiuchao Li, Yu Cui, Guohua

More information

PNEUMATIC HIGH SPEED SPINDLE WITH AIR BEARINGS

PNEUMATIC HIGH SPEED SPINDLE WITH AIR BEARINGS PNEUMATIC HIGH SPEED SPINDLE WITH AIR BEARINGS Terenziano RAPARELLI, Federico COLOMBO and Rodrigo VILLAVICENCIO Department of Mechanics, Politecnico di Torino Corso Duca degli Abruzzi 24, Torino, 10129

More information

Transient Analysis of Offset Stator Double Sided Short Rotor Linear Induction Motor Accelerator

Transient Analysis of Offset Stator Double Sided Short Rotor Linear Induction Motor Accelerator Transient Analysis of Offset Stator Double Sided Short Rotor Linear Induction Motor Accelerator No. Fred Eastham Department of Electronic and Electrical Engineering, the University of Bath, Bath, BA2 7AY,

More information

4. Electromechanical Systems. Karadeniz Technical University Department of Electrical and Electronics Engineering Trabzon, Turkey.

4. Electromechanical Systems. Karadeniz Technical University Department of Electrical and Electronics Engineering Trabzon, Turkey. Karadeniz Technical University Department of Electrical and Electronics Engineering 61080 Trabzon, Turkey Chapter 3-4-1 Modelling of Physical Systems 4. Electromechanical Systems Bu ders notları sadece

More information

Numerical Investigation of Diesel Engine Characteristics During Control System Development

Numerical Investigation of Diesel Engine Characteristics During Control System Development Numerical Investigation of Diesel Engine Characteristics During Control System Development Aleksandr Aleksandrovich Kudryavtsev, Aleksandr Gavriilovich Kuznetsov Sergey Viktorovich Kharitonov and Dmitriy

More information

Page 1. Design meeting 18/03/2008. By Mohamed KOUJILI

Page 1. Design meeting 18/03/2008. By Mohamed KOUJILI Page 1 Design meeting 18/03/2008 By Mohamed KOUJILI I. INTRODUCTION II. III. IV. CONSTRUCTION AND OPERATING PRINCIPLE 1. Stator 2. Rotor 3. Hall sensor 4. Theory of operation TORQUE/SPEED CHARACTERISTICS

More information

Researches regarding a pressure pulse generator as a segment of model for a weighing in motion system

Researches regarding a pressure pulse generator as a segment of model for a weighing in motion system IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Researches regarding a pressure pulse generator as a segment of model for a weighing in motion system To cite this article: I

More information

APPLICATION OF A NEW TYPE OF AERODYNAMIC TILTING PAD JOURNAL BEARING IN POWER GYROSCOPE

APPLICATION OF A NEW TYPE OF AERODYNAMIC TILTING PAD JOURNAL BEARING IN POWER GYROSCOPE Colloquium DYNAMICS OF MACHINES 2012 Prague, February 7 8, 2011 CzechNC APPLICATION OF A NEW TYPE OF AERODYNAMIC TILTING PAD JOURNAL BEARING IN POWER GYROSCOPE Jiří Šimek Abstract: New type of aerodynamic

More information

Modeling the Neuro-Fuzzy Control with the Dynamic Model of the Permanent Magnet DC Motor

Modeling the Neuro-Fuzzy Control with the Dynamic Model of the Permanent Magnet DC Motor SISY 2006 4 th Serbian-Hungarian Joint Symposium on Intelligent Systems Modeling the Neuro-Fuzzy Control with the Dynamic Model of the Permanent Magnet DC Motor Ottó Búcsú, Gábor Kávai, István Kecskés,

More information

Development of Engine Clutch Control for Parallel Hybrid

Development of Engine Clutch Control for Parallel Hybrid EVS27 Barcelona, Spain, November 17-20, 2013 Development of Engine Clutch Control for Parallel Hybrid Vehicles Joonyoung Park 1 1 Hyundai Motor Company, 772-1, Jangduk, Hwaseong, Gyeonggi, 445-706, Korea,

More information

RESEARCH OF THE DYNAMIC PRESSURE VARIATION IN HYDRAULIC SYSTEM WITH TWO PARALLEL CONNECTED DIGITAL CONTROL VALVES

RESEARCH OF THE DYNAMIC PRESSURE VARIATION IN HYDRAULIC SYSTEM WITH TWO PARALLEL CONNECTED DIGITAL CONTROL VALVES RESEARCH OF THE DYNAMIC PRESSURE VARIATION IN HYDRAULIC SYSTEM WITH TWO PARALLEL CONNECTED DIGITAL CONTROL VALVES ABSTRACT The researches of the hydraulic system which consist of two straight pipelines

More information

Analysis of Effect of Throttle Shaft on a Fuel Injection System for ICES

Analysis of Effect of Throttle Shaft on a Fuel Injection System for ICES International Journal of Electronic and Electrical Engineering. ISSN 0974-2174 Volume 7, Number 2 (2014), pp. 113-120 International Research Publication House http://www.irphouse.com Analysis of Effect

More information

EE 370L Controls Laboratory. Laboratory Exercise #E1 Motor Control

EE 370L Controls Laboratory. Laboratory Exercise #E1 Motor Control 1. Learning Objectives EE 370L Controls Laboratory Laboratory Exercise #E1 Motor Control Department of Electrical and Computer Engineering University of Nevada, at Las Vegas To demonstrate the concept

More information

STUDY ON MAXIMUM POWER EXTRACTION CONTROL FOR PMSG BASED WIND ENERGY CONVERSION SYSTEM

STUDY ON MAXIMUM POWER EXTRACTION CONTROL FOR PMSG BASED WIND ENERGY CONVERSION SYSTEM STUDY ON MAXIMUM POWER EXTRACTION CONTROL FOR PMSG BASED WIND ENERGY CONVERSION SYSTEM Ms. Dipali A. Umak 1, Ms. Trupti S. Thakare 2, Prof. R. K. Kirpane 3 1 Student (BE), Dept. of EE, DES s COET, Maharashtra,

More information

TORQUE-MOTORS. as Actuators in Intake and Exhaust System. SONCEBOZ Rue Rosselet-Challandes 5 CH-2605 Sonceboz.

TORQUE-MOTORS. as Actuators in Intake and Exhaust System. SONCEBOZ Rue Rosselet-Challandes 5 CH-2605 Sonceboz. TORQUE-MOTORS as Actuators in Intake and Exhaust System SONCEBOZ Rue Rosselet-Challandes 5 CH-2605 Sonceboz Tel.: +41 / 32-488 11 11 Fax: +41 / 32-488 11 00 info@sonceboz.com www.sonceboz.com as Actuators

More information

Impact of Cold and Hot Exhaust Gas Recirculation on Diesel Engine

Impact of Cold and Hot Exhaust Gas Recirculation on Diesel Engine RESEARCH ARTICLE OPEN ACCESS Impact of Cold and Hot Exhaust Gas Recirculation on Diesel Engine P. Saichaitanya 1, K. Simhadri 2, G.Vamsidurgamohan 3 1, 2, 3 G M R Institute of Engineering and Technology,

More information

Dynamic Response Analysis of Small Wind Energy Conversion Systems (WECS) Operating With Torque Control versus Speed Control

Dynamic Response Analysis of Small Wind Energy Conversion Systems (WECS) Operating With Torque Control versus Speed Control European Association for the Development of Renewable Energies, Environment and Power Quality International Conference on Renewable Energies and Power Quality (ICREPQ 9) Valencia (Spain), th to 17th April,

More information

Transient analysis of a new outer-rotor permanent-magnet brushless DC drive using circuit-field-torque coupled timestepping finite-element method

Transient analysis of a new outer-rotor permanent-magnet brushless DC drive using circuit-field-torque coupled timestepping finite-element method Title Transient analysis of a new outer-rotor permanent-magnet brushless DC drive using circuit-field-torque coupled timestepping finite-element method Author(s) Wang, Y; Chau, KT; Chan, CC; Jiang, JZ

More information

Vibration Measurement and Noise Control in Planetary Gear Train

Vibration Measurement and Noise Control in Planetary Gear Train Vibration Measurement and Noise Control in Planetary Gear Train A.R.Mokate 1, R.R.Navthar 2 P.G. Student, Department of Mechanical Engineering, PDVVP COE, A. Nagar, Maharashtra, India 1 Assistance Professor,

More information

INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY

INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY [Sarvi, 1(9): Nov., 2012] ISSN: 2277-9655 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY A Sliding Mode Controller for DC/DC Converters. Mohammad Sarvi 2, Iman Soltani *1, NafisehNamazypour

More information

Modeling and Simulation of Five Phase Inverter Fed Im Drive and Three Phase Inverter Fed Im Drive

Modeling and Simulation of Five Phase Inverter Fed Im Drive and Three Phase Inverter Fed Im Drive RESEARCH ARTICLE OPEN ACCESS Modeling and Simulation of Five Phase Inverter Fed Im Drive and Three Phase Inverter Fed Im Drive 1 Rahul B. Shende, 2 Prof. Dinesh D. Dhawale, 3 Prof. Kishor B. Porate 123

More information

Analysis of Torsional Vibration in Elliptical Gears

Analysis of Torsional Vibration in Elliptical Gears The The rd rd International Conference on on Design Engineering and Science, ICDES Pilsen, Czech Pilsen, Republic, Czech August Republic, September -, Analysis of Torsional Vibration in Elliptical Gears

More information

Enhancement of Power Quality in Transmission Line Using Flexible Ac Transmission System

Enhancement of Power Quality in Transmission Line Using Flexible Ac Transmission System Enhancement of Power Quality in Transmission Line Using Flexible Ac Transmission System Raju Pandey, A. K. Kori Abstract FACTS devices can be added to power transmission and distribution systems at appropriate

More information

International Conference on Mechanics, Materials and Structural Engineering (ICMMSE 2016)

International Conference on Mechanics, Materials and Structural Engineering (ICMMSE 2016) International Conference on Mechanics, Materials and Structural Engineering (ICMMSE 2016) Comparison on Hysteresis Movement in Accordance with the Frictional Coefficient and Initial Angle of Clutch Diaphragm

More information

Comparative Study of Maximum Torque Control by PI ANN of Induction Motor

Comparative Study of Maximum Torque Control by PI ANN of Induction Motor Comparative Study of Maximum Torque Control by PI ANN of Induction Motor Dr. G.Madhusudhana Rao 1 and G.Srikanth 2 1 Professor of Electrical and Electronics Engineering, TKR College of Engineering and

More information

Cooling Enhancement of Electric Motors

Cooling Enhancement of Electric Motors Cooling Enhancement of Electric Motors Authors : Yasser G. Dessouky* and Barry W. Williams** Dept. of Computing & Electrical Engineering Heriot-Watt University Riccarton, Edinburgh EH14 4AS, U.K. Fax :

More information

Low Speed Control Enhancement for 3-phase AC Induction Machine by Using Voltage/ Frequency Technique

Low Speed Control Enhancement for 3-phase AC Induction Machine by Using Voltage/ Frequency Technique Australian Journal of Basic and Applied Sciences, 7(7): 370-375, 2013 ISSN 1991-8178 Low Speed Control Enhancement for 3-phase AC Induction Machine by Using Voltage/ Frequency Technique 1 Mhmed M. Algrnaodi,

More information

INTEGRATED HYDRO-MECHANICAL SIMULATION OF A CAM-ROCKER ARM-UNIT INJECTOR SYSTEM TO ADDRESS NOISE AND VIBRATION ISSUES

INTEGRATED HYDRO-MECHANICAL SIMULATION OF A CAM-ROCKER ARM-UNIT INJECTOR SYSTEM TO ADDRESS NOISE AND VIBRATION ISSUES GT-Suite Users Conference Frankfurt, Germany, October 10 th 2005 INTEGRATED HYDRO-MECHANICAL SIMULATION OF A CAM-ROCKER ARM-UNIT INJECTOR SYSTEM TO ADDRESS NOISE AND VIBRATION ISSUES R. HAM, H. FESSLER

More information

UNIAIR Variable Valve Actuation System Modelling and Integration to the Engine in the GT-SUITE environment

UNIAIR Variable Valve Actuation System Modelling and Integration to the Engine in the GT-SUITE environment 2008 European Conference Frankfurt am Main October, 20th Variable Valve Actuation System Modelling Integration to the Engine in the environment Paolo Ferreri - Caterina Venezia FPT Research & Mechanical

More information

Modeling, Design and Simulation of Active Suspension System Frequency Response Controller using Automated Tuning Technique

Modeling, Design and Simulation of Active Suspension System Frequency Response Controller using Automated Tuning Technique Modeling, Design and Simulation of Active Suspension System Frequency Response Controller using Automated Tuning Technique Omorodion Ikponwosa Ignatius Obinabo C.E Evbogbai M.J.E. Abstract Car suspension

More information

Simulation and Analysis of Vehicle Suspension System for Different Road Profile

Simulation and Analysis of Vehicle Suspension System for Different Road Profile Simulation and Analysis of Vehicle Suspension System for Different Road Profile P.Senthil kumar 1 K.Sivakumar 2 R.Kalidas 3 1 Assistant professor, 2 Professor & Head, 3 Student Department of Mechanical

More information

Rotor Position Detection of CPPM Belt Starter Generator with Trapezoidal Back EMF using Six Hall Sensors

Rotor Position Detection of CPPM Belt Starter Generator with Trapezoidal Back EMF using Six Hall Sensors Journal of Magnetics 21(2), 173-178 (2016) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 http://dx.doi.org/10.4283/jmag.2016.21.2.173 Rotor Position Detection of CPPM Belt Starter Generator with Trapezoidal

More information

MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS

MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS POLISH MARITIME RESEARCH Special Issue 2018 S2 (98) 2018 Vol. 25; pp. 30-34 10.2478/pomr-2018-0070 MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS

More information

Bushing connector application in Suspension modeling

Bushing connector application in Suspension modeling Bushing connector application in Suspension modeling Mukund Rao, Senior Engineer John Deere Turf and Utility Platform, Cary, North Carolina-USA Abstract: The Suspension Assembly modeling in utility vehicles

More information

Theoretical and Experimental Evaluation of the Friction Torque in Compressors with Straddle Bearings

Theoretical and Experimental Evaluation of the Friction Torque in Compressors with Straddle Bearings Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 1998 Theoretical and Experimental Evaluation of the Friction Torque in Compressors with

More information

3rd International Conference on Material, Mechanical and Manufacturing Engineering (IC3ME 2015)

3rd International Conference on Material, Mechanical and Manufacturing Engineering (IC3ME 2015) 3rd International Conference on Material, Mechanical and Manufacturing Engineering (IC3ME 2015) A High Dynamic Performance PMSM Sensorless Algorithm Based on Rotor Position Tracking Observer Tianmiao Wang

More information

UTILIZATION OF PNEUMATIC ACTUATOR

UTILIZATION OF PNEUMATIC ACTUATOR UTILIZATION OF PNEUMATIC ACTUATOR Rupesh Parkhi 1 UG Student, Department of Mech, G.H.Raisoni College of Engineering, Nagpur, RTMN University ABSTRACT The pneumatic actuator represents the main force control

More information

Design of Position Detection Strategy of Sensorless Permanent Magnet Motors at Standstill Using Transient Finite Element Analysis

Design of Position Detection Strategy of Sensorless Permanent Magnet Motors at Standstill Using Transient Finite Element Analysis Design of Position Detection Strategy of Sensorless Permanent Magnet Motors at Standstill Using Transient Finite Element Analysis W. N. Fu 1, and S. L. Ho 1, and Zheng Zhang 2, Fellow, IEEE 1 The Hong

More information

Chapter 7: DC Motors and Transmissions. 7.1: Basic Definitions and Concepts

Chapter 7: DC Motors and Transmissions. 7.1: Basic Definitions and Concepts Chapter 7: DC Motors and Transmissions Electric motors are one of the most common types of actuators found in robotics. Using them effectively will allow your robot to take action based on the direction

More information

QFT CONTROL APPLIED TO A DRIVE BY WIRE (DBW) SYSTEM

QFT CONTROL APPLIED TO A DRIVE BY WIRE (DBW) SYSTEM QFT CONTROL APPLIED TO A DRIVE BY WIRE (DBW) SYSTEM Fabio Delatore (a), Fabrizio Leonardi (b), Alexsander T. Carvalho (c), Carlos A. Morioka (d) (b) Centro Universitario da FEI Sao Bernardo do Campo/SP

More information

EFFECTIVENESS OF THE ACTIVE PNEUMATIC SUSPENSION OF THE OPERATOR S SEAT OF THE MOBILE MACHINE IN DEPEND OF THE VIBRATION REDUCTION STRATEGIES

EFFECTIVENESS OF THE ACTIVE PNEUMATIC SUSPENSION OF THE OPERATOR S SEAT OF THE MOBILE MACHINE IN DEPEND OF THE VIBRATION REDUCTION STRATEGIES Journal of KONES Powertrain and Transport, Vol. 25, No. 3 2018 EFFECTIVENESS OF THE ACTIVE PNEUMATIC SUSPENSION OF THE OPERATOR S SEAT OF THE MOBILE MACHINE IN DEPEND OF THE VIBRATION REDUCTION STRATEGIES

More information

Chapter 2 Dynamic Analysis of a Heavy Vehicle Using Lumped Parameter Model

Chapter 2 Dynamic Analysis of a Heavy Vehicle Using Lumped Parameter Model Chapter 2 Dynamic Analysis of a Heavy Vehicle Using Lumped Parameter Model The interaction between a vehicle and the road is a very complicated dynamic process, which involves many fields such as vehicle

More information

Module7:Advanced Combustion Systems and Alternative Powerplants Lecture 32:Stratified Charge Engines

Module7:Advanced Combustion Systems and Alternative Powerplants Lecture 32:Stratified Charge Engines ADVANCED COMBUSTION SYSTEMS AND ALTERNATIVE POWERPLANTS The Lecture Contains: DIRECT INJECTION STRATIFIED CHARGE (DISC) ENGINES Historical Overview Potential Advantages of DISC Engines DISC Engine Combustion

More information

Actuators are the muscles of robots.

Actuators are the muscles of robots. 6.1 INTRODUCTION Actuators are the muscles of robots. Several types of actuator noteworthy? Electric motors? Servomotors? Stepper motors? Direct-drive electric motors? Hydraulic actuators? Pneumatic actuators?

More information

Analysis of Torque and Speed Controller for Five Phase Switched Reluctance Motor

Analysis of Torque and Speed Controller for Five Phase Switched Reluctance Motor Analysis of Torque and Speed Controller for Five Phase Switched Reluctance Motor Ramesh Kumar. S 1, Dhivya. S 2 Assistant Professor, Department of EEE, Vivekananda Institute of Engineering and Technology

More information

Sliding Mode Control of Boost Converter Controlled DC Motor

Sliding Mode Control of Boost Converter Controlled DC Motor Sliding Mode Control of Boost Converter Controlled DC Motor Reshma Jayakumar 1 and Chama R. Chandran 2 1,2 Member, IEEE Abstract Nowadays automation of industries are increasing, with the rapid development

More information