Catalog # Project. Comments. Prepared by. Warranty Five year warranty.

Transcription

1 DESCRIPTION The Define series by Neo-Ray characterizes the ultimate in minimalist simplicity by providing clean, uniform lines of illumination in virtually any architectural environment. Powered s most advanced linear LED technology, the Define series delivers outstanding efficacy in a variety of profile widths. 1.5, 2, 3, 4 and 5 luminaire widths are all specifiable to the nearest inch in length and can be fitted with standard flush, asymmetric wall, asymmetric coridor, regressed and drop lensing. In-ceiling and in-wall corners as well as wall to ceiling transitions can all be ordered as standard components and blend seamlessly into the most complex architectural spaces. Custom transitions are also available. Robust construction and adaptable, modular components make installation simple and ensure laser straight runs. SPECIFICATION FEATURES Catalog # Project Comments Prepared by Neo-Ray Type Date Construction Precision cut housing trim extruded from 6063 aluminum with aluminum frame. Extruded end-caps ensure a precise and uniform ceiling interface. Nominal 2-12 illuminated sections used in run configuration and/or individual fixtures. Finish Fixture housing trims are high reflective white (unless otherwise specified) using electrostatically applied polyester powder coat paint. LED Module Modular LED tray assembly comprising quick disconnect wire-harness for ease of installation and maintence over the life of the luminaire. Offered with two next generation Neo- Ray light engines delivering industry leading efficacy and long-life. LED s are available in 2700K, 3000K, 3500K or 4000K. CRI options of either 80CRI or 90CRI are available. Lumen output will be effected - please refer to the lumen adjustment factor table. LED Drivers LED system coupled with electrical driver to deliver optimal performance. Traditional electronic drivers are available for V and 347V applications. s DLVP Low voltage drivers are available for 48VDC applications. Controls and Integrated Sensors Equipped standard with a 0-10V continuous dimming driver compatible with most standard dimming devices. Additional control types are available (DALI, Lutron, DLVP) at an additional cost. WaveLinx and LumaWatt Pro wireless sensors as well as stand-alone sensors available. Warranty Five year warranty. reflector, light engine, led driver and DEFINE " 5.625" LED Recessed Perimeter Direct culus 1598 Damp Location Listed LM79/LM80 Compliant ROHS Compliant Lumawatt Pro Wireless WaveLinx Wireless Made in USA 3.680" S124DRP 3.680" S124RDRP ORDERING INFORMATION Sample Number: S124DRP-S1020D840-ETG4F0-1B1-UDD-F-W-SWPD1 Light Distribution Lumen Package Down CCT & Min CRI Celing Type Length Circuiting S124DRP = Define 4 Direct Recessed Perimeter S124RDRP = Define 4 Regressed Direct Recessed Perimeter -S = Standard -H = High Performance 350D = 350 Lms/ft 575D = 575 Lms/ft 795D = 795 Lms/ft 1020D = 1020 Lms/ft 1195D = 1195 Lms/ft D = Custom Lm/Ft 830 = 3000K, 80CRI 835 = 3500K, 80CRI 840 = 4000K, 80CRI 927 = 2700K, 90CRI 930 = 3000K, 90CRI 935 = 3500K, 90CRI 940 = 4000K, 90CRI -ETG = 15/16 T-Grid -FTG = 9/16 T-Grid -STG = 9/16 Slot T-Grid -FTT = 9/16 Tegular T-Grid -ITG = 9/16 Interlude T-Grid -ETT = 15/16 Tegular T-Grid -GYP = Gypsum board -FSR = Flangeless Gypsum Board -FES = Finished Extruded Side 2F0 = 2 Individual 4F0 = 4 Individual 8F0 = 8 Individual 12F0 = 12 Individual F0 = 4 Incremental Run (e.g. 40F0 = 40 0 ) F_ = 1 Incremental Run (e.g. 21F3 = 21 3 ) -1 = Single Circuit -S = Secondary Circuit RDR regress of 1 will add an additional 1 to fixture depth. Please refer to performance table to determine based on efficacy requirements. Price adder applies for H configuration. 3500K/80CRI/DR housing/f Lens. Please refer to scaling data for other variables. For custom lumen output, please refer to additional information on page 2. Additional lead-time may apply for 927, 930, 935 and 940 configurations. Please refer to ceiling interface diagrams for additional detail and dimensions. Secondary circuit similar to A/B switching. Price adder applies for S configuration. Emergency Voltage Integral LED Driver Shielding Down Options Color Integrated Sensor E = Emergency circuit B1 = Surelite 7W UNV integral battery B2 = Surelite 14W UNV integral battery T = Iota UL924 ETR Emergency Bypass Relay -U = UNV V -1 = 120V -2 = 277V -3 = 347V -4 = 48VDC DD= 0-10 Volt Dimming, 1% 5L = DALI Dimming, 5%-100% L5 = Lutron 5-Series LDE5 w/ecosys LH = Lutron HiLume LDE1 w/ecosys LU = Lutron HiLume L3D w/3w LV1 = DLVP -F = Satin Flush Diffuser -A = Asymmetric Wall -C = Asymmetric Corridor -D = Satin Drop Diffuser -CP = Chicago Plenum -R = GLR Fuse (Fast) -F = GLF Fuse (Slow) -W = Matte White -S = Silver -B = Black -C = Custom Color -SWPD1 = WaveLinx Integral -SWTPD1 = WaveLinx Tilemount -LWIPD1 = LumaWatt Pro Integral -LWTPD1 = LumaWatt Pro Tilemount -SVPD1 = Standalone Sensor -SVTPD1 = Standalone Sensor Tilemount Internal battery standard for fixtures 4ft and lumen output 1200Lms/ft. Fixture Non-IC-Rated for internal battery and lumen output 1025 Lms/ft. External battery standard with chicago plenum. 48V for use with LV1 driver. 347V only availabe with DD and 5L drivers. DD driver is standard. All lensing options are snap-in lenses Contact factory for custom color Please refer to page 5 for additional detail required to specify integrated or tile-mount sensors. Integral option not available with regressed, drop or asymmetric configurations. Tilemount configuration recommended for these applications. Grey bar denotes not available with Define Core10-Day Quick ship options 1 of 5

2 SPECIFICATION FEATURES CONTINUED Mounting Recessed Perimeter. Lengths Available in any length (23 min) with a resolution of 1 inch. Max section length of 12ft (8ft max option available). Additional fixture lengths are available - please consult factory. All lengths are nominal. Actual sizes are one inch shorter than nominal to allow easy in-grid installation. For Gypsum or Flangeless installations add 1 inch to overall fixture length. Refer to ceiling type section of specification sheetand submittal drawings for actual sizes. Corners and Transition Pieces Corners and other transition pieces are fully luminous and contructed using precision mitered frame and lens components. The frame is welded to ensure a precise and robust assembly. Standard 9 horizontal and vertical corners as well as custom corners are available. Please consult online linear configutor or the factory for precise corner locations and for ordering. Alternative transition pieces such as T s, Y s, X s, etc. are also available. Snap-In Lensing Options Satin Flush - Flush, high diffusion glare-free lens Satin Proud - 1 Proud, high diffusion glare-free lens Asymmetric Wall - Low-glare Asymmetric lens Asymmetric Corridor - Asymmetric lens optimized to drive light away from wall and into the corridor Flush options ship with our patent-pending underlens solution, while the proud lens ships with an injection molded end cap to eliminate light leak. Reflectors Precision formed cold-rolled steel reflectors with high reflectivity (standard) and ultra-high reflectivity (used with High Performance light engine). Lumen Maintenance 90% (L90) of initial light output at 100,000+ hrs. 70% (L70) of initial light output at 400,000+ hrs, reported L70 >60,000 hrs. Derived from TM-21 C ambient and typical operating conditions. Consult factory for additional data. Custom Lumen Output You can select a custom lumen output for your application in Lumens per foot (e.g. -725D for 725 Lms/ft down). Desired output must with within the total light output range. Please contact factory for custom lumen output when not selecting the standard 0-10V DD Driver. TOTAL LIGHT OUTPUT RANGE (lms/ft) CCT 80CRI 90CRI 2700K N/A K K K If your requirement is expressed in power consumption (W/ft) rather than light output, you can use the power to lumen output curves to convert power consumption to light output for specification. Efficacy for custom lumen outputs can be estimated using lumen output curves or with the use of our online custom lumen output tool. Electrical Dimming provided as standard - dimming wires are capped with wire-nuts for non-dimming applications. Optional battery backup options provided. Default battery location is internal to fixture to reduce field wiring with pre-wired external test switch. Default emergency section is 4ft in length and located at the beginning of the fixture unless designated elsewhere using our linear product configurator tool. To estimate lumen output from the emergency section, multiply battery wattage x minimum fixture efficacy from performance table below (e.g. 14W x 116 lm/w = 1624 lms). Our ETS-DR option will provide switching for both power and wires for applications requiring a UL924 transfer device. Integrated Sensors Please reference page 5 for details. Weight 2.65 lbs per foot. Approvals culus Meets NYC requirements. Meets CCEC requirements (Chicago Plenum). Suitable for damp locations. IC Rated (except where noted) PHOTOMETRIC OVERVIEW AND PERFORMANCE DATA PERFORMANCE PER LINEAR FOOT AT 3500K/80CRI Nominal Lumen Output Standard High Performance 350 lms/ft 2.9 W/ft 121 lm/w 2.8 W/ft 127 lm/w 575 lms/ft 4.7 W/ft 122 lm/w 4.3 W/ft 131 lm/w 795 lms/ft 6.6 W/ft 121 lm/w 5.9 W/ft 134 lm/w 1020 lms/ft 8.7 W/ft 117 lm/w 7.9 W/ft 130 lm/w 1195 lms/ft 10.3 W/ft 116 lm/w 9.4 W/ft 126 lm/w LUMEN ADJUSTMENT FACTORS CCT 80CRI 90CRI 2700K N/A K K K LUMEN ADJUSTMENT CALCULATIONS Example 1 - Adjusted Lumen Output Nominal Lumen Output selected = 1025 lms/ft (based on standard of 3500K/80CRI) Lumen Adjustment Factor = (2700K/90CRI desired) Adjusted Lumen Output = Nominal Lumen Output x Lumen Adjustment Factor Adjusted Lumen Output = 1025 lms/ft x = 821 lms/ft Example 2 - Custom Lumen Output based on Required Lumens Per Foot Total light output (4ft) requirement of 2800 lms, desired CCT and CRI of 4000K/80CRI Total required lumens per 4000K= 2800 lms / 4 ft = 700 lms/ft Lumen Adjustment Factor = (Requirement based on 4000K / 80CRI) Total required lumens per 3500K / 80CRI = 700 lms/ft = 688 lms/ft Estimated efficacy = 121 lm/w (find nearest value using table above) Estimated power consumption = 688 lms/ft 121 lm/w = 5.69 W/ft SHEILDING OPTIONS S124DR with Flush Satin Lens (F) S124DR with Drop Satin Lens (D) S124RDR with Regressed Satin Lens (F) S124DR with Flush Asymmetric Wall (A) or Asymmetric Corridor (C) 2 of 5

3 PHOTOMETRICS FILE NAME: S124DR-S795D835-GYP4F0-1-UDD-F-W CCT: 3500K LUMENS: 3203 Lms WATTS: 26.2 W LPW: LPW TEST G SATIN FLUSH LENS 0º-30º º-40º º-60º º-90º FILE NAME: S124DR-S795D835-GYP4F0-1-UDD-D-W CCT: 3500K LUMENS: 3045 Lms WATTS: 26.4 W LPW: LPW TEST G SATIN DROP LENS 0º-30º º-40º º-60º º-90º [25.4MM] 90º-120º º-150º º-180º FILE NAME: S124RDR-S795D835-GYP4F0-1-UDD-F-W CCT: 3500K LUMENS: 3018 Lms WATTS: 26.4 W LPW: LPW TEST G REGRESSED SATIN DIFFUSER 1 [25.4MM] 0º-30º º-40º º-60º º-90º ASYMMETRIC LENS ASYMMETRIC CORRIDOR LENS FILE NAME: CCT: LUMENS: WATTS: LPW: S124DR-S795D835-GYP4F0-1-UDD-A-W 3500K 3331 Lms 26.4 W LPW TEST NUMBER: G º-30º º-40º º-60º º-90º CANDELA DISTRIBUTION (CD) Vertical Angle 0º of 5

4 CEILING TYPE Extruded Trim Flange Details - Refer to submittal drawings for detailed flange information - for additional options consult factory. Grid Ceiling Systems 15/16 Tee (ETG) 9/16 Tee (FTG) 9/16 Slotted Tee (STG) TO S TO S TO S 9/16 Tegular (FTT) 15/16 Tegular (ETT) 9/16 Interlude Tee (ITG) TO S TO S TO S Drywall Ceiling Visible Flange (GYP) Mud-In Flange (FSR) NOTE: ACTUAL LENGTH OF GYP/FSR FIXURES WILL BE 1 SHORTER IN LENGTH THAN TOTAL REQUESTED FOR ALL RECESSED / PERIMETER FIXTURES = FIXTURE ORDER LENGTH - 1 E.G. - OF 3 11 WILL SHIP WHEN ORDERING A 4F0 FIXTURE CEILING CUTOUT = OR CEILING CUTOUT = FIXTURE ORDER LENGTH E.G. - CEILING CUTOUT WHEN ORDERING A 4F0 LENGTH FIXTURE WILL BE " TO CUTOUT CEILING CUTOUT 4.125" TO CUTOUT MUD CEILING CUTOUT Other Ceiling Systems (Wood, Fabric, Metal Pan, HD Box) Finished Extruded Side (FES) Typical Installations using Finished Extruded Side (FES) Finished Side WOOD SLAT WOOD PANELING FABRIC PANELS METAL PAN 4 of 5

5 CORNER TRANSITIONS INTEGRATED SENSOR DETAILS AND PLACEMENT Sensor Type Wireless Sensor Integration Sensor Mounting Ordering Code WaveLinx Yes Integral to Fixture Mounted in solid cover SWPD1 LumaWatt Pro (enlighted) Stand-Alone SVPD1 Pre-wired for tile-mount Installation in ceiling tile or J-Box cover SWTPD1 Yes Integral to Fixture Mounted in illuminated lens LWIPD1 Pre-wired for tile-mount Installation in ceiling tile or J-Box cover LWTPD1 No Integral to Fixture Mounted in solid cover SVPD1 Standard Sensor with Luminaire Control Auxilary Sensor used for Sensor Coverge (wireless systems only) INTEGRAL SENSOR Pre-wired for tile-mount Installation in ceiling tile or J-Box cover SVTPD1 Optional standalone and wireless connnected integrated sensors require use of the DD (0-10V) driver. WaveLinx and LumaWatt Pro sensors require additional system hardware (not provided) for full functionality. Tilemount sensor recommended for optimal sensor coverage on perimeter applications. Tilemount sensor not available with Chicago plenum option. Standard sensor layout is shown below. Please refer to sensor coverage pattern diagrams to ensure proper coverage for the application. Standard configurations are available in both individual fixtures and in continous runs. Default spacing is based on the maximum fixture length of 12ft and can be changed to 8ft sensor spacing for additional coverage by selecting the 8ft max fixture length option when ordering. For additional information integrated sensors and connected lighting, please visit s Connected Lighting Website. TILEMOUNT SENSOR (OPTIMAL LOCATION) 8ft Individual Individual >8ft Individual Beginning of Run (BOR) Beginning of Run (BOR) Intermediate Section (INT) Intermediate Section (INT) (EOR) > 8ft (EOR) 8ft Note: When 8ft max section length and EOR 3ft, sensor placement moved to right (end) side of EOR fixture. 5 of 5