Cyclone II. Cyclone. and OPERATOR S MANUAL IMPORTANT- READ OPERATOR S MANUAL BEFORE USE.

Transcription

1 Cyclone and Cyclone II OPERATOR S MANUAL IMPORTANT- READ OPERATOR S MANUAL BEFORE USE Page Ave. Michigan Center, Michigan Rev. 0410

2 Introduction To the Cyclone and Cyclone II owner: Thank you for purchasing the Cyclone and/or Cylone II pump cart. The Cyclone and Cyclone II low pressure adhesive pump carts are bulk delivery systems specifically designed to dispense a two-component 1:1 ratio low viscosity adhesive. The Cyclone includes 1 gun and 35 feet of hose. The Cyclone II includes 2 guns and 70 feet of hose. Features and Benefits: Bulk delivery system for low material cost Saves time and labor compared to mechanical fastening Clean, contained adhesive delivery system Gun and hoses stay clean and free flowing Lightweight Low maintenance Easy to maneuver The Cyclone and Cyclone II pump carts are designed to install beads of VOC free PG-1 Pump Grade Insulation Adhesive to adhere most types of roof insulation. Refer to the PG-1 product data sheet for a complete list of insulations and substrates. Please take a moment to familiarize yourself with the information in this manual regarding pump features ( how to instructions), care, maintenance and more. Should you have any questions, please contact ADCO Roofing Products, Field Tech Service Department at Introduction

3 Table of Contents Safety Instructions...1 Cyclone and Cyclone II...2 Accessories and Required Tools...2 Component Summary...3 Operating Instructions...4 Step 1: Installing Grease into Manifold...4 Step 2: Loading Adhesive Boxes...4 Step 3: Connecting Box Fittings...4 Step 4: Powering up Pump System...4 Step 5: Purging the System...4 Step 6: Installing Static Mixing Nozzle...4 Step 7: Applying Adhesive...4 Step 8: Shut-down Procedures...4 Troubleshooting...5 Parts Breakdown...6 Motor/Pump Assembly...6 Frame and Components...6 Gun Assembly...6 Warranty...7 Table of Contents

4 Safety Instructions WARNING IMPORTANT SAFETY INSTRUCTIONS-READ BEFORE OPERATING EQUIPMENT! Protective equipment such as safety glasses and protective gloves must be worn when operating or servicing the Cyclone and Cyclone II. The Cyclone and Cyclone II run on 110 volt 60Hz, 20 amp AC current. Use a grounded power cord that is in good condition, rated for outdoor use, and a minimum of 14-guage construction. Servicing electrical components should only be done by trained personnel and only after disconnecting power to the pump. Under no circumstances should any acid or corrosive chemicals be used in the machine. The electrical circuitry is not of explosion proof design and should not be used in any environment, or with any product, requiring such a design. The Cyclone and Cyclone II operate with pressure. The applicator gun should never be pointed at or near people. The gun should never be actuated when the outlet tip is blocked or restricted by any object, cured foam, or some part of the body. Prior to working with any product be sure to read labels and the Material Safety Data Sheets (MSDS). Take necessary health and safety precautions. To prevent damage to the pump always make sure box labeled Part 1 is loaded into the Part 1 tray (color coded white) and box labeled Part 2 is loaded into the Part 2 tray (color coded blue). Improper placement and connection of PG-1 Pump Grade Insulation Adhesive boxes can damage the pump system. Make sure fittings match! Black to black and gray to gray. To avoid personal injury caused by electrical shock DO NOT open access switch panel on back of Cyclone or Cyclone II, or remove front cover of the AC Drive while power is on. Do not use in rain or wet conditions. Keep cord and motor dry. Always remove Static Mixing Nozzles during any pause in application or operation. If Static Mixing Nozzle remains on the gun assembly residual adhesive can react and harden in the gun system. Page 1

5 Accessories and Required Tools Cyclone Cyclone II Provided Accessories: Required for Operation (Not Provided): Grease Gun & 2 tubes of grease 110 volt 60 Hz, 20 amp power source 10 Retaining nuts for mixing tips 2 black quick connect fittings 1 gray quick connect fitting MSDS Grounded 14 gauge (min) outdoor power cord Waste container Recommended for Maintenance: SAE hex key (Allen wrench) set 2 adjustable wrenches Basic SAE wrench set Cyclone System Solution (flush material) Page 2

6 Component Summary Lifting Bar *Tray Assembly Part 1 & 2 *Gravity Feed Hose (with gray and black female quick connect fittings) *Hose Hanging Bracket *Gun Assembly *Motor & Pump Assembly Electrical Box *Pressure Switch Assembly 35 of Hose (70 of hose included on Cyclone II) *Power Switch *Pump Switch *Pump Speed * 2 sets included on Cyclone II Page 3

7 STEP 1. Pump grease into gun manifold. With the valves closed, place the gun over a waste container and pump grease into the fittings until in runs out of the tip. STEP 2. Insert adhesive box labeled Part 1 into the tray labeled Part 1 (color coded white). Insert adhesive box labeled Part 2 into tray labeled Part 2 (color coded blue). STEP 3. Place grease on quick connectors prior to attachment. Attach quick connect fitting. Quick connect fittings must match up! Part 1= Black to Black Part 2= Gray to Gray STEP 4. Plug in power cord to a source that can provide 110 volt 60 Hz, 20 amp service. Do not use an extension cord longer than 100 feet or run additional equipment off of the cord. With the gun in the OFF position, flip power switch to ON. After power has been supplied to the machine (approxmately 15 seconds) proceed by turning the pump switch to the ON position. Set speed switch to LOW. Motor will run until it senses pressure in the Part 2 hose and then it will shut off automatically. This is normal. Do not turn the power or pump switch off. STEP 5. Slowly open valve on gun assembly, motor will start automatically. Let a small amount of material flow out into a waste container and ensure that an equal amount of material is flowing out of each opening of the threaded tip of the manifold. Shut off gun, motor will stop automatically. STEP 6. Apply grease to the threaded manifold tip and to the mixing tip threads. Attach a static mixing nozzle to the threaded tip of the manifold. Ensure that it is completely seated. IMPORTANT!: Remove static mixing nozzles from gun manifold during any pause in application or operation. If static mixing nozzle remains on gun, material will react and harden in the gun assembly and possibly the ends of the hose. During removal and attachment of static mixing nozzles an adjustable wrench may be necessary to turn the nozzle retaining nut. Be sure the static mixing nozzle is fully seated on the threaded manifold tip. When using plastic retaining nuts do not allow pressure to build up in the static mixing nozzle. STEP 7. Open valves and dispense adhesive directly to the substrate as recomended by the product manufacturer. Dispensing speed of adhesive can be adjusted to LOW, MED, or HIGH depending on how much is needed. STEP 8. Operating Instructions Shut-down Close gun assembly valves. Flip pump switch to OFF. Remove static mixing nozzle and discard. Place metal static mixing nozzle retaining nut in solvent. Retaining nut must be resused with each new static mixing nozzle. If using plastic retaining nut discard and use a new one. Relieve any pressure in hoses by opening and closing gun assembly valve. Pump grease into both fittings at the top of the gun manifold until it flows out of the threaded tip. Pump grease into Part 1 grease fitting first. Prior to long-term storage (30 days) flush the hoses and manifold with Cyclone System Solution. Page 4

8 Issue Cyclone will not turn on Adhesive does not flow from gun Cyclone pumps unequal amounts of Part 1 and Part 2 Adhesive will not foam Adhesive has no holding power Suggestion Troubleshooting 1. Check power supply 2. With the pump switch OFF, turn power switch to ON and wait 15 seconds. 3. Make sure power cord is not longer than 100 feet. 1. With mixing tip off, point gun into a waste container and move gun handle to ON. On a new machine it may take1-2 minutes for material to flow. 2. Check for blockage in gun or hose. Clear blockage if detected. Blockage in manifold can be cleared by disassembly. 3. With the power OFF, remove coupling guard on Part 1 pump (White). Rotate coupling with a pipe wrench, or by hand. If coupling cannot be rotated internal damage may have occurred. 1. Make sure Part 1 and Part 2 material are at the correct application temperature. 2. Check for blockage in gun or hose. Clean blockage if detected. 3. Check connections of supply lines to boxes. Ensure correct connection. 1. 1:1 mix ratio is off check gun and hose for blockage. Clear blockage if detected. 2. Check material level in boxes. Levels should be equal. 1. 1:1 mix ratio is off. 2. Material has been damaged as a result of improper storage in cold temperatures. 3. Verify material is within manufacturer s stated shelf life. Page 5

9 Parts Breakdown 15 1 MOTOR/PUMP ASSEMBLY KEY DESCRIPTION PART # 1 Connector-Black /4 Supply Hose-White K W c 6a 10 6b Hose Clamp HC /2 x3/4 Hose Brass BHB Pump-White F432W 6a 5/8 Shaft Coupling b Spider Coupling c 1/2 Shaft Coupling /2 npt 90 Brass Elbow BP /2 x 5/8 #10 N.P.T Str FS Motor 5K49KN Gear Box 4Z /2 x1/2 #8 JIC Fem /2 Brass Tee Female BP /2 Check Valve /4 Supply Hose-Blue K B Connector-Gray Pressure Switch PS100LPF 17 Pump-Blue F432B 18 Hex Bushing 1/2 x 1/8 HBSTEEL 6 3 FRAME AND COMPONENTS KEY DESCRIPTION PART # 1 8 Swivel Wheel 44SFF825S-TB 2 10 Wheel SO Grease Gun Grease /2 Hose Assembly 35 Part 1 & 35 Part 2 6 Cyclone System Sol. #1 Cyclone System Sol. #2 GUN ASSEMBLY KEY DESCRIPTION PART # 3440 EQ-CSS1B-A01 EQ-CSS1B-B01 1 Retaining Nut(10) N-P Tip Block M 3 O Rings OR110-BUNA 4 Grease Fitting H Block 1-1/2 square x 3 6 3/8 x1/2 swivel adap /2 Ball Valve BV500BRFP /2 Threaded Pipe ALUM501/2THRD 9 1/2 x1/2 #8 JIC Male /2 x 5/8 #10 N.P.T Str FS 1008 Page 6 11 Mixing Tip(10)

10 Warranty WARRANTY AND REMEDY ADCO warrants its products to conform to ADCO s specifications at the time of sale when tested according to ADCO standards. If a product is proven to be defective when tested according to ADCO standards, ADCO will, at its option, refund the purchase price or replace or repair the defective product within 30 days after sale by ADCO or it s distributors. THIS LIMITED WARRANTY IS THE BUYERS SOLE AND EXCLUSIVE REMEDY AGAINST ADCO AND IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE. In no event shall ADCO be liable for any special, incidental, consequential, or punitive damages arising out of any claims whether based on negligence, contract, warranty, strict liability or otherwise. The Cyclone and Cyclone II are designed to dispense PG-1 Pump Grade Insulation Adhesive. Use of other adhesives must be approved by ADCO prior to running them through the equipment. ADCO will not take any responsibility for repairing machines damaged by thrid party chemicals. All statements and technical information in this document are based on tests or data that ADCO believes is reliable. However, ADCO does not warrant or guarantee the accuracy or completeness of this information. The user has sole knowledge and control of factors that can affect the performance of ADCO s products in the user s intended application. It is the user s responsibility to conduct tests to determine the compatibility of ADCO s product design, structure, and materials of the user s end product and the suitability of ADCO s product for the user s method of application and intended use. The user assumes all risk and liability arising out of such use. Cyclone and Cyclone II 4401 Page Ave. Michigan Center, Michigan Page 7