SECTION 2E TIRES AND WHEELS TABLE OF CONTENTS
|
|
- William Milo Arnold
- 5 years ago
- Views:
Transcription
1 SECTION 2E TIRES AND WHEELS TABLE OF CONTENTS Specifications E-1 General Specifications E-1 Fastener Tightening Specifications E-1 Diagnosis E-2 Wear Pattern Diagnosis E-2 Identification E-3 Radial Tire E-3 Wheel Disc E-3 Component Locator E-4 Wheel and Tire E-4 Maintenance and Repair E-5 On-Vehicle Service E-5 Wheels and Tires E-5 SPECIFICATIONS GENERAL SPECIFICATIONS Wheel Tire Application Material Size Type Size and Tire Pressure Description Alumimun 7JJ X 15 Radial Tire P215 / 75R 15-30psi P235 / 75R 15-30psi P255 / 70R 15-30psi FASTENER TIGHTENING SPECIFICATIONS Wheel Bolt Application Steel Alumimum Nlm
2 2E-2 TIRES AND WHEELS DIAGNOSIS WEAR PATTERN DIAGNOSIS Wear Pattern Possible Cause Remedy Wear on Both Tread Shoulders Under Inflation Wear on Tread Center Over Inflation Tread Torn Out Under Inflation One-sided Tread Wear Incorrect Camber or Toe-in Feather Edging of Tread Incorrect Toe-in Spotty Tread Wear Out of Wheel Balance Spotty Wear-wear Localized on Shoulder Sections Out of Wheel Balance Play in Hub Bearings Play in Ball Joint Defective Shock Absorber Check play preload Check Check
3 TIRES AND WHEELS 2E-3 IDENTIFICATION RADIAL TIRE P 215/75 R H M+S Four Season Mud & Snow Speed Rating (max. 210km/h) Load Range (below 670kg) Rim Diameter (inch) Radial Tire Aspect Ratio = (Section Height Section Width) x 100 Section Width (mm) Passenger Car 215/65 R V Speed Rating (max. 240km/h) Load Range (below 650kg) Rim Diameter (inch) Radial Tire Aspect Ratio = (Section Height Section Width) x 100 Section Width(mm) Summer Tire WHEEL DISC 7 J x 16 ET 39 Wheel Offset (mm) (Distance from rim center to wheel nave contacting surface) Rim Diameter (inch) Identification for One-piece Well-base Rim Code Letter for Height and Profile of Rim Flange Rim Width (Inch) ET : a : d : Distance from Rim Center to Wheel have Contacting Surface (mm) Rim Width (Inch) Rim Diameter (Inch)
4 2E-4 TIRES AND WHEELS WHEEL AND TIRE COMPONENT LOCATOR 1 Wheel Bolts... Steel Wheel : Nm... Aluminium Wheel : Nm 2 Steel Wheel 3 Aluminium Wheel 4 Tire 5 Steel Wheel Weight Balance 6 Hub Cap
5 TIRES AND WHEELS 2E-5 MAINTENANCE AND REPAIR ON-VEHICLE SERVICE WHEELS AND TIRES Removal & Installation Procedure 1. Inspection of tire Check tread area for tread surface, crack, damage by nail in or stones. Replace or repair if necessary. 2. Wear limit. Limit 1.6mm l Replace the tire if tread-wear indicator of the tread grooves appears where marked ' '. l The wear limit of snow tire is the same as normal tire (1.6mm) and indicator location is marked ' '. 3. Runout measurement. l Excessive runout of tires and wheels can cause the abnormal wear of tire. Using a dial indicator, measure wheel and tire runout. l Measure radial runout at the rim flange and center of the tire tread area. Standard 2.66mm l Measure lateral runout at the tire bead area of the wheel and tire sidewall. Standard 2.03mm Notice If runout is excessive, replace the tire or wheel.
6 2E-6 TIRES AND WHEELS 4. Tire pressure inspection. l Tire pressure. Front & Rear (P235/75R15) 2 2.1kg/cm (30PSI) l Check tread contact with road. Notice l If underinflated, tire may come away from the wheel during rapid steering. l An overinflated tire will cause a hard riding and uneven wear. 5. Wheel balance. l Balance weights should be on each side. When the wheel is out of balance or a tire has been repaired, be sure to balance the wheel again. l If total weight is over 150g, readjust the balance by reinstalling the tire on the wheel. l Balance weight should not protrude from the wheel rim over 3mm. l For aluminum wheel, use aluminum wheel balance weight only.
7 TIRES AND WHEELS 2E-7 l To correct unbalance, install equal weights 180 opposite each other, one on the inside of the wheel and one on the outside, at the point of unbalance. l Balance Weight 10g 20g 30g 40g 50g 60g 0.4oz 0.7oz 1.10oz 1.40oz 1.80oz 2.1oz 6. Cautions for installation and removal. l Clean the mounting surfaces of hub and wheel. l Do not apply grease or oil on the nuts and bolts (It will cause looseness and poor tightening). l Using a jack, lift up the tire about 3cm from the ground. l Tighten nuts in a criss-cross pattern 2-3 times. Tighten Torque Steel : Nm Aluminium : Nm
Tire 16 inch 225/75R inch 255/60R 18
417009 133 1. SPECIFICATIONS Description Specification Tire 16 inch 225/75R 16 Tire inflation pressure 18 inch 255/60R 18 Front: 32 psi Rear: 32 psi (44 psi: when the vehicle is fully laden with luggage)
More informationReturn To Main Table of Contents GENERAL... 2 STRUT ASSEMBLY LOWER ARM STABILIZER BAR CENTER MEMBER WHEEL AND TIRE...
FRONT SUSPENSION Return To Main Table of Contents GENERAL... 2 STRUT ASSEMBLY... 11 LOWER ARM... 13 STABILIZER BAR... 17 CENTER MEMBER... 19 WHEEL AND TIRE... 21 GENERAL GENERAL SPECIFICATIONS Suspension
More informationWHEEL AND TIRE GROUP CONTENTS WHEEL AND TIRE DIAGNOSIS WHEEL AND TIRE SPECIFICATIONS ON-VEHICLE SERVICE...
31-1 GROUP 31 CONTENTS DIAGNOSIS.... 31-2 DIAGNOSIS........................ 31-2 WHEEL BALANCE ACCURACY........ 31-3 ON-VEHICLE SERVICE........... 31-6 TIRE INFLATION PRESSURE CHECK... 31-6 TIRE WEAR CHECK..................
More informationWHEEL AND TIRE GROUP CONTENTS WHEEL AND TIRE DIAGNOSIS WHEEL AND TIRE SPECIFICATIONS ON-VEHICLE SERVICE...
31-1 GROUP 31 CONTENTS.... 31-2 DIAGNOSIS........................ 31-2 WHEEL BALANCE ACCURACY........ 31-3 ON-VEHICLE SERVICE........... 31-7 TIRE INFLATION PRESSURE CHECK... 31-7 TIRE WEAR CHECK..................
More informationTire 16 inch 225/75R inch 255/60R 18
417009 143 1. SPECIFICATIONS Description Specification Tire 16 inch 225/75R 16 Tire inflation pressure 18 inch 255/60R 18 Front: 32 psi Rear: 32 psi (44 psi: when the vehicle is fully laden with luggage)
More informationWHEEL AND TIRE GROUP CONTENTS WHEEL AND TIRE DIAGNOSIS WHEEL AND TIRE SPECIFICATIONS ON-VEHICLE SERVICE...
31-1 GROUP 31 CONTENTS DIAGNOSIS.... 31-2 DIAGNOSIS........................ 31-2 WHEEL BALANCE ACCURACY........ 31-3 ON-VEHICLE SERVICE........... 31-6 TIRE INFLATION PRESSURE CHECK... 31-6 TIRE WEAR CHECK..................
More informationTIRES AND WHEELS 22-1 TIRES AND WHEELS CONTENTS
ZJ TIRES AND WHEELS 22-1 TIRES AND WHEELS CONTENTS TIRES... 1 WHEELS... 7 TIRES INDEX DESCRIPTION AND OPERATION RADIAL-PLY TIRES... 2 REPLACEMENT TIRES... 3 SPARE TIRE TEMPORARY... 2 TIRE INFLATION PRESSURES...
More informationWHEEL AND TYRE GROUP CONTENTS WHEEL AND TYRE DIAGNOSIS WHEEL AND TYRE SPECIFICATIONS ON-VEHICLE SERVICE...
31-1 GROUP 31 WHEEL AND TYRE CONTENTS... 31-2 DIAGNOSIS........................ 31-2 WHEEL BALANCE ACCURACY........ 31-3 ON-VEHICLE SERVICE........... 31-7 TYRE INFLATION PRESSURE CHECK.. 31-7 TYRE WEAR
More informationTIRES AND WHEELS 22-1 TIRES AND WHEELS CONTENTS
PL TIRES AND WHEELS 22-1 TIRES AND WHEELS CONTENTS page page TIRES... 1 WHEELS... 8 TIRES INDEX page DESCRIPTION AND OPERATION RADIAL-PLY TIRES... 2 REPLACEMENT TIRES... 3 SPARE TIRE TEMPORARY... 2 TIRE
More information2001 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX
2001 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX CHASSIS SECTION FRONT SUSPENSION FS REAR SUSPENSION RS WT This service manual has been prepared to provide SUBARU service personnel with the necessary
More informationWHEELS AND TIRES 22-1 WHEELS AND TIRES CONTENTS
J WHEELS AND TIRES 22-1 WHEELS AND TIRES CONTENTS page SPECIFICATIONS... 12 TIRES... 1 page VEHICLE VIBRATION... 10 WHEELS... 6 TIRES INDEX page Cleaning of Tires... 2 General Information... 1 Pressure
More informationWHEEL AND TIRE GROUP CONTENTS GENERAL SPECIFICATIONS SERVICE SPECIFICATIONS WHEEL AND TIRE
31-1 GROUP 31 CONTENTS GENERAL SPECIFICATIONS...... 31-2 SERVICE SPECIFICATIONS....... 31-2 DIAGNOSIS.... 31-3 DIAGNOSIS........................ 31-3 WHEEL BALANCE ACCURACY........ 31-4 ON-VEHICLE SERVICE...........
More informationWHEEL AND TYRE GROUP 31 CONTENTS ON-VEHICLE SERVICE GENERAL INFORMATION SERVICE SPECIFICATIONS TROUBLESHOOTING...
GROUP 31 CONTENTS GENERAL INFORMATION........ 31-2 SERVICE SPECIFICATIONS....... 31-2............ 31-3 DIAGNOSIS........................ 31-3 WHEEL BALANCE ACCURACY........ 31-4 ON-VEHICLE SERVICE...........
More informationTIRES AND WHEELS 22-1 TIRES AND WHEELS CONTENTS
ZG TIRES AND WHEELS 22-1 TIRES AND WHEELS CONTENTS TIRES... 1 WHEELS... 7 TIRES INDEX DESCRIPTION AND OPERATION RADIAL-PLY TIRES... 2 REPLACEMENT TIRES... 3 SPARE TIRE (TEMPORARY)... 2 TIRE INFLATION PRESSURES...
More informationSuspension System GENERAL... SS -2 FRONT SUSPENSION SYSTEM... SS -9. REAR SUSPENSION SySTEM... SS -22 TIRESIWHEELS... SS -28
Suspension System GENERAL... SS -2 FRONT SUSPENSION SYSTEM... SS -9 REAR SUSPENSION SySTEM... SS -22 TIRESIWHEELS... SS -28 SS -2 SUSPENSION SYSTEM GENERAL SPECIFICATIONS EHMB0100 Front suspension system
More informationWHEELS BEARINGS TIRES
GROUP 22 WHEELS BEARINGS TIRES CONTENTS Page GENERAL INFORMATION 1 SERVICE DIAGNOSIS 1 SERVICE PROCEDURES... 2 WHEELS... 2 Page BEARINGS 2 TIRES 4 SPECIFICATIONS AND TIGHTENING REFERENCE.. In Rear of Manual
More informationSECTION Wheels and Tires
204-04-i Wheels and Tires 204-04-i SECTION 204-04 Wheels and Tires CONTENTS PAGE DIAGNOSIS AND TESTING Wheels And Tires... 204-04-2 Inspection and Verification... 204-04-2 Tire Wear... 204-04-3 Symptom
More informationROAD WHEELS & TIRES SECTION CONTENTS E SUSPENSION WT-1
E SUSPENSION A SECTION ROAD WHEELS & TIRES B C D CONTENTS WT NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING... 2 NVH Troubleshooting Chart... 2 ROAD WHEEL... 3 Inspection... 3 WHEEL AND TIRE ASSEMBLY...
More information7IR. Hosted and optimised by Wheels & Tyres. Section J /K. N.B. Suspension part numbers begin with (G)
7IR ---- - - - - - - - - - - -- - - - - - - - - Section J /K - Wheels & Tyres N.B. Suspension part numbers begin with (G \ contents... 11 Tyre Inspection... 0 Wheel Inspection... [1.... Valve Inspection.......
More informationROAD WHEELS & TIRES SECTION CONTENTS E SUSPENSION WT-1
E SUSPENSION A SECTION ROAD WHEELS & TIRES B C D CONTENTS WT NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING... 2 NVH Troubleshooting Chart... 2 WHEEL... 3 Inspection... 3 WHEEL AND TIRE ASSEMBLY...
More information2004 SUSPENSION. Tires And Wheels - Corvette. Fastener Tightening Specifications Specification Application Wheel Nuts In Sequence 140 N.
2004 SUSPENSION Tires And Wheels - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Wheel Nuts In Sequence 140 N.m
More informationSECTION 7 - SUSPENSION
For Arctic Cat Discount Parts Call 606-678-9623 or 606-561-4983 SECTION 7 - SUSPENSION 7 TABLE OF CONTENTS Front and Rear Suspension Assembly Schematics... 7-2 Shock Absorbers... 7-2 Swing Arm... 7-5 Front
More informationTrailer Wheel & Tire Facts
Trailer Wheel & Tire Facts Trailer Wheel & Tire Facts Replacing the wheels and tires on your trailer shouldn t be a difficult task, but then you hear terms like load range, bias, radial, pilot diameter
More informationTire Information. Example of a wear indicator mark
Tire Information Maintenance To safely operate your vehicle, your tires must be of the proper type and size, in good condition with adequate tread, and properly inflated. Inflation Guidelines Properly
More informationFRONT & REAR SUSPENSION SECTIONSU CONTENTS IDX. FRONT SUSPENSION...2 Precautions...2
FRONT & REAR SUSPENSION SECTIONSU GI MA EM LC EC CONTENTS FE...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration and Harshness (NVH)
More informationModern Auto Tech Study Guide Chapter 65 & 66 Pages Tires, Wheels, Bearings 51 Points. Automotive Service. Danger of Old Tires!!
Modern Auto Tech Study Guide Chapter 65 & 66 Pages 1241 1278 Tires, Wheels, Bearings 51 Points Automotive Service Danger of Old Tires!! Tires Manufactured Since 2000 Since 2000, the week and year the tire
More information-GROUP 22 CONTENTS' WHEELS-BEARINGS-TIRES
-GROUP 22 WHEELS-BEARINGS-TIRES CONTENTS' Page BEARINGS (FRONT WHEEL) 6 Removal (Without Disc Brakes) 6 Removal (With Disc Brakes) 6 Cleaning and Inspection... 6 Lubrication 6 Installation (Without Disc
More informationROAD WHEELS & TIRES SECTION CONTENTS E SUSPENSION WT-1
ROAD WHEELS & TIRES E SUSPENSION A SECTION ROAD WHEELS & TIRES B C D CONTENTS WT NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING... 2 NVH Troubleshooting Chart... 2 ROAD WHEEL... 3 Inspection... 3
More informationTIRE PRODUCT KNOWLEDGE Just the Facts!
K + M Tire TIRE PRODUCT KNOWLEDGE Just the Facts! TIRE FUNCTIONS Carry the Vehicle s Weight and Load Transmit Acceleration Forces Transmit Braking Forces Transmit Cornering Forces Cushion Road Irregularities
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION REAR SUSPENSION DIAGNOSIS LOWER ARM AND TOE CONTROL ARM ASSEMBLY...
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION........... 34-2 DIAGNOSIS.... 34-2 INTRODUCTION....................... 34-2 TROUBLESHOOTING STRATEGY........ 34-2 SYMPTOM CHART..................... 34-3 SYMPTOM
More informationTire & Wheel Fundamentals
Tire & Wheel Fundamentals 1 Tire Function Provide traction (friction) with the road surface Provide cushion between the road and the metal wheel 2 Tire Construction Tube Tires Have a tube inside the tire
More informationGENERAL INFORMATION. Wheel Alignment Theory & Operation
Fig. 1: Checking Steering Linkage GENERAL INFORMATION Wheel Alignment Theory & Operation ADJUSTMENTS NOTE: This article is intended for general information purposes only. This information may not apply
More informationGROUP 33A 33A-1 CONTENTS GENERAL DESCRIPTION... 33A-2 FRONT SUSPENSION DIAGNOSIS. 33A-3 LOWER ARM... 33A-13 SPECIAL TOOLS... 33A-5
33A-1 GROUP 33A CONTENTS GENERAL DESCRIPTION 33A-2 DIAGNOSIS 33A-3 INTRODUCTION TO FRONT SUSPENSION DIAGNOSIS 33A-3 DIAGNOSIS TROUBLESHOOTING STRATEGY 33A-3 SYMPTOM CHART 33A-3 SYMPTOM PROCEDURES 33A-3
More information1. General Description
General Description 1. General Description A: SPECIFICATION Front Rear Model Wheel arch height (Tolerance: +12 mm 24 mm ( +0.47 in 0.94 in)) mm (in) 376 (14.8) Camber (Tolerance: 0 45 Differences between
More informationFRONT SUSPENSION GROUP 33A 33A-1 CONTENTS GENERAL DESCRIPTION... 33A-2 FRONT SUSPENSION DIAGNOSIS. 33A-3 LOWER ARM... 33A-13 SPECIAL TOOLS...
33A-1 GROUP 33A FRONT SUSPENSION CONTENTS GENERAL DESCRIPTION......... 33A-2 DIAGNOSIS. 33A-3 INTRODUCTION TO DIAGNOSIS........................ 33A-3 DIAGNOSIS TROUBLESHOOTING STRATEGY...... 33A-3 SYMPTOM
More informationSECTION 6 3 SERVICE PROCEDURES AND SPECIFICATIONS. Chassis
SERVICE PROCEDURES AND SPECIFICATIONS Chassis SECTION 6 3 Specifications........................................... 208 Checking brake fluid...................................... 210 Checking power steering
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM ASSEMBLY REAR SUSPENSION DIAGNOSIS
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION......... 34-2 DIAGNOSIS.. 34-3 INTRODUCTION TO DIAGNOSIS........................ 34-3 DIAGNOSIS TROUBLESHOOTING STRATEGY...... 34-3 SYMPTOM CHART...................
More informationREAR SUSPENSION SECTION CONTENTS E SUSPENSION RSU-1 RSU
E SUSPENSION A SECTION REAR SUSPENSION B C D CONTENTS RSU PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION, AND HARSHNESS (NVH)
More informationIf it exceeds the maximum specification, replace the propeller shaft.
If it exceeds the maximum specification, replace the propeller shaft. Maximum runout o 0.4 mm {0.016 in} 2. Inspect the play and rotation of the joint by turning the universal joint in the directions shown
More informationSECTION G HUBS, WHEELS AND TYRES. Section Description Page G.1 GENERAL DESCRIPTION 3 G.2 FRONT HUBS 3 G.3 FRONT HUBS - REMOVE AND REPLACE 4
SECTION G HUBS, WHEELS AND TYRES Section Description Page G.1 GENERAL DESCRIPTION 3 G.2 FRONT HUBS 3 G.3 FRONT HUBS - REMOVE AND REPLACE 4 G.4 REAR HUBS - REMOVE AND REPLACE 5 G.5 WHEELS 6 G.6 TYRES 6
More informationPage 1 of 8 SECTION 204-00: Suspension System - General Information 1998 Contour/Mystique Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 09/14/2001 Suspension System Special Tool(s) Dial
More informationFRONT & REAR SUSPENSION SECTIONSU CONTENTS IDX. FRONT SUSPENSION...2 Precautions...2. REAR SUSPENSION...14 Precautions...14
FRONT & REAR SUSPENSION SECTIONSU GI MA EM LC EC CONTENTS FE FRONT SUSPENSION...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration
More informationREAR SUSPENSION GROUP CONTENTS GENERAL INFORMATION FASTENER TIGHTENING SPECIFICATIONS TRAILING ARM...
34-1 GROUP 34 CONTENTS GENERAL INFORMATION 34-2 FASTENER TIGHTENING SPECIFICATIONS 34-4 GENERAL SPECIFICATIONS 34-4 SERVICE SPECIFICATIONS 34-5 LUBRICANTS 34-5 DIAGNOSIS 34-6 INTRODUCTION TO DIAGNOSIS
More informationBRAKE SYSTEM Return To Main Table of Contents
BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...
More informationREAR AXLE GROUP CONTENTS GENERAL DESCRIPTION REAR AXLE DIAGNOSIS REAR AXLE HUB ASSEMBLY KNUCKLE...
27-1 GROUP 27 CONTENTS GENERAL DESCRIPTION......... 27-2 DIAGNOSIS......... 27-2 INTRODUCTION TO DIAGNOSIS........................ 27-2 DIAGNOSTIC TROUBLESHOOTING STRATEGY...... 27-2 SYMPTOM CHART...................
More informationGroup 22 WHEELS, BEARINGS AND TIRES CONTENTS DATA AND SPECIFICATIONS
WHEELS, BEARINGS AND TIRES 1 Group 22 WHEELS, BEARINGS AND TIRES CONTENTS Paragraph Page 12 5 15 8 Care of Tires 8 4 13 6 14 7 1 2 10 5 Wheel Balance 9 4 11 5 DATA AND SPECIFICATIONS MODELS DESOTO (PS-1,
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
TJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 5 page REAR SUSPENSION... 12 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION
More informationWheels. Wheels and Tires ! CAUTION. Wheel Selection
Wheel Selection Wheels Wheels are very important and critical components of your running gear system. When specifying or replacing your trailer wheels it is important that the wheels, tires, and axle are
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
TJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 13 ALIGNMENT INDEX page DESCRIPTION AND OPERATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION
More informationSECTION 6 3 SERVICE PROCEDURES AND SPECIFICATIONS. Chassis
SERVICE PROCEDURES AND SPECIFICATIONS Chassis SECTION 6 3 Specifications........................................... 174 Checking brake fluid...................................... 176 Checking brake pedal
More informationSECTION 6 3 SERVICE PROCEDURES AND SPECIFICATIONS. Chassis
SECTION 6 3 SERVICE PROCEDURES AND SPECIFICATIONS Chassis Specifications 206 Checking brake fluid 208 Checking power steering fluid 209 Checking tire pressure 210 Rotating tires 211 Checking and replacing
More informationFRONT SUSPENSION GROUP CONTENTS GENERAL INFORMATION SPECIFICATIONS STRUT ASSEMBLY FRONT SUSPENSION DIAGNOSIS.
33-1 GROUP 33 FRONT SUSPENSION CONTENTS GENERAL INFORMATION 33-2 SPECIFICATIONS 33-3 FASTENER TIGHTENING SPECIFICATIONS 33-3 GENERAL SPECIFICATIONS 33-3 SERVICE SPECIFICATIONS 33-3 LUBRICANT 33-3 DIAGNOSIS
More informationFRONT & REAR SUSPENSION SECTIONSU CONTENTS IDX. FRONT SUSPENSION...2 Precautions...2
FRONT & REAR SUSPENSION SECTIONSU GI MA EM LC CONTENTS EC FE FRONT SUSPENSION...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration
More informationDIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING SUSPENSION AND STEERING SYSTEM 2007 SUSPENSION Suspension - Nitro CONDITION POSSIBLE CAUSES CORRECTION FRONT END NOISE 1. Loose or worn wheel bearings. 1. Replace wheel bearings.
More informationAlternate Lug Wear. Appearance. What's Happening. Probable Causes
Alternate Lug Wear The tire's lugs are not wearing consistently because they are not making uniform contact with the highway. mismatched duals inconsistent dual inflation (10 PSI or greater) tread design/tire
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
ZJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 14 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION
More informationFRONT SUSPENSION SECTION FSU CONTENTS E SUSPENSION FSU-1 FSU
FRONT SUSPENSION E SUSPENSION SECTION FSU A FRONT SUSPENSION B C D CONTENTS FSU PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION
More informationSECTION 3D REAR AXLE TABLE OF CONTENTS
SECTION 3D REAR AXLE TABLE OF CONTENTS General Description and Operation... 3D-2 Specifications... 3D-2 Fastener Tightening Specifications... 3D-2 Diagnostic Information and Procedures... 3D-3 Component
More informationSECTION FA CONTENTS FRONT AXLE & FRONT SUSPENSION IDX
CONTENTS FRONT AXLE & FRONT SUSPENSION SECTION FA GI MA EM LC EC FE PRECAUTIONS AND PREPARATION...2 Precautions...2 Special Service Tools...2 Commercial Service Tools...3 NOISE, VIBRATION AND HARSHNESS
More informationFRONT SUSPENSION SECTION CONTENTS E SUSPENSION FSU-1 FSU
E SUSPENSION A SECTION FRONT SUSPENSION B C D CONTENTS FSU PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE VIBRATION AND HARSHNESS (NVH)
More informationFRONT AXLE AND SUSPENSION FA 1
FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated
More informationTyre Care & Safety for Agricultural Tires
Tyre Care & Safety for Agricultural Tires Operating Instructions Some Points Worth Remembering; The BKT Agricultural tires are designed for Agricultural tractors, Trailers & Implements. Before using them
More informationWheels. Wheels and Tires ! CAUTION. Wheel Selection
Wheels Wheel Selection Wheels are a very important and critical component of your running gear system. When specifying or replacing your trailer wheels it is important that the wheels, tires, and axle
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
WJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 4 page REAR SUSPENSION... 15 ALIGNMENT INDEX page AND WHEEL ALIGNMENT... 1 SERVICE PROCEDURES PRE-ALIGNMENT... 2 AND WHEEL
More informationSUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
XJ SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 7 page REAR SUSPENSION... 16 ALIGNMENT TABLE OF CONTENTS page AND WHEEL ALIGNMENT...1 DIAGNOSIS AND TESTING SUSPENSION
More information11. FRONT WHEEL/SUSPENSION/
11 FRONT WHEEL/SUSPENSION/ SERVICE INFORMATION------------------------------------------------ 11-2 TROUBLESHOOTING----------------------------------------------------- 11-3 HANDLEBAR ---------------------------------------------------------------
More informationFRONT SUSPENSION SECTION FSU CONTENTS E SUSPENSION FSU-1 FSU
FRONT SUSPENSION E SUSPENSION SECTION FSU A FRONT SUSPENSION B C D CONTENTS FSU PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools (SST)... 3 Commercial Service Tools... 3 NOISE, VIBRATION
More informationSECTION 3A FRONT DRIVE AXLE TABLE OF CONTENTS SPECIFICATIONS GENERAL SPECIFICATIONS. Description Drive Shaft Type. CV Joint Axle Housing Type
SECTION 3A FRONT DRIVE AXLE TABLE OF CONTENTS Specifications........................ 3A-1 General Specifications.................. 3A-1 Fastener Tightening Specifications......... 3A-2 Component Locator...................
More information1. Stabilizer 4-1 [S100] SPECIFICATION AND SERVICE DATA. 1. Stabilizer. Bar dia. Model. COUPE 19 mm (0.75 in) 13 mm (0.51 in)
4-1 [S100] SPECIFICATION AND SERVICE DATA 1. Stabilizer 1. Stabilizer Model Bar dia. Front Rear COUPE 19 mm (0.75 in) 13 mm (0.51 in) SEDAN 2200 cc 18 mm (0.71 in) 2500 cc 19 mm (0.75 in) 13 mm (0.51 in)
More informationRotate tires according to manufacturer's recommendations. (P-1) Reinstall wheel; torque lug nuts. (P-1)
JOB SHEET 8 Rotating Tires Name: Station: Date: NATEF Correlation This Job Sheet addresses the following NATEF task(s): 4.F.3 4.F.8 Rotate tires according to manufacturer's recommendations. (P-1) Reinstall
More informationAbout Tires. Tire Function. Tire Size Designation For
About Tires Tire Function Over one hundred years' experience of tire technology has enabled Pirelli to combine in their products maximum levels of security, longevity, comfort and attention to the environment.
More informationFRONT SUSPENSION GROUP 2 FRONT SUSPENSION 2-1 CONTENTS SPECIFICATIONS VC-1, VC-2, VC-3 VY-1 TOOL LIST. Page
GROUP 2 FRONT SUSPENSION CONTENTS Page Specifications 1 Tool List.... 1 Torque Reference 2 Preparation for Measuring Front End Alignment... 2 Front Suspension Height Adjustment 3 Front Suspension Alignment
More informationFRONT & REAR SUSPENSION SECTIONSU CONTENTS IDX. FRONT SUSPENSION...2 Precautions...2. Service Data and Specifications (SDS)...21
FRONT & REAR SUSPENSION SECTIONSU GI MA EM LC EC CONTENTS FE...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration and Harshness (NVH)
More informationSUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL
More informationREAR AXLE AND SUSPENSION RA 1
REAR AXLE AND SUSPENSION RA1 RA2 REAR AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated Replace tires or inflate to
More informationROAD WHEELS & TIRES SECTION CONTENTS E SUSPENSION WT-1
ROAD WHEELS & TIRES E SUSPENSION A SECTION ROAD WHEELS & TIRES B C D CONTENTS WT PREPARATION... 2 Special Service Tools... 2 Commercial Service Tools... 2 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...
More informationFRONT SUSPENSION GROUP CONTENTS GENERAL INFORMATION ON-VEHICLE SERVICE FASTENER TIGHTENING SPECIFICATIONS...
33-1 GROUP 33 FRONT SUSPENSION CONTENTS GENERAL INFORMATION 33-2 FASTENER TIGHTENING SPECIFICATIONS 33-2 GENERAL SPECIFICATIONS 33-3 SERVICE SPECIFICATIONS 33-3 LUBRICANTS 33-3 DIAGNOSIS 33-4 INTRODUCTION
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM REAR SUSPENSION DIAGNOSIS TOE CONTROL ARM...
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION 34-2 DIAGNOSIS 34-3 INTRODUCTION TO DIAGNOSIS 34-3 DIAGNOSTIC TROUBLESHOOTING STRATEGY 34-3 SYMPTOM CHART 34-3 SYMPTOM PROCEDURES 34-3 SPECIAL TOOLS 34-5 ON-VEHICLE
More informationTires and wheels. Introduction
Tires and wheels Applicable only in the United States and Canada Introduction In this section you ll find information about: Tire and wheel handling Wheel rims Tire inflation pressure Tire inflation pressure
More informationa s s w m m INDEX Page
w 'y 'i s m m a s s w m m INDEX Page Page Abieraal Tire Weir 2H-3 Tire Rotation 2H-5 General 2H-1 Tire Roughness 2H-8 Polyspare Tire 2H-5 Tire Size and Load Rating 2H-2 Wide Tread and Snow Tire Applications
More informationFRONT SUSPENSION SECTION FSU CONTENTS E SUSPENSION FSU-1 2WD AWD FSU
FRONT SUSPENSION E SUSPENSION SECTION FSU A FRONT SUSPENSION B C D CONTENTS FSU 2WD PRECAUTIONS... 3 Caution... 3 PREPARATION... 4 Special Service Tools (SST)... 4 Commercial Service Tools... 4 NOISE,
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
DN SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 5 page REAR SUSPENSION... 13 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING PRE-ALIGNMENT
More informationROAD WHEELS & TIRES SECTION WT CONTENTS E SUSPENSION WT-1
ROAD WHEELS & TIRES E SUSPENSION SECTION WT A ROAD WHEELS & TIRES B C D CONTENTS WT NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING... 2 NVH Troubleshooting Chart... 2 ROAD WHEEL... 3 Inspection...
More informationSECTION 6 3 SERVICE PROCEDURES AND SPECIFICATIONS. Chassis
SERVICE PROCEDURES AND SPECIFICATIONS Chassis SECTION 6 3 Specifications........................................... 204 Checking brake fluid...................................... 206 Checking brake pedal
More informationFRONT AXLE & FRONT SUSPENSION SECTIONFA CONTENTS
FRONT AXLE & FRONT SUSPENSION SECTIONFA CONTENTS PRECAUTIONS...2 PREPARATION...3 FRONT AXLE AND FRONT SUSPENSION...4 CHECK AND ADJUSTMENT...5 Front Axle and Front Suspension Parts...5 Front Wheel Bearing...6
More informationOwner s Manual Enclosed Cargo
Owner s Manual Enclosed Cargo 1 This manual contains safety information and instructions for your trailer. You must read this manual before loading or towing your trailer. You must follow all safety precautions
More informationTRUCK AND BUS TYRE I TECHNICAL MANUAL MAINTENANCE AND CARE
TRUCK AND BUS TYRE I TECHNICAL MANUAL MAINTENANCE AND CARE About tyre inflation Truck alignment and tyre wear Tyre damage TECHNICAL INFORMATION MAINTENANCE AND CARE About tyre inflation ONE OF THE MOST
More informationFRONT SUSPENSION SECTION CONTENTS E SUSPENSION FSU-1 2WD FSU
FRONT SUSPENSION E SUSPENSION A SECTION FRONT SUSPENSION B C D CONTENTS FSU 2WD PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools (SST)... 3 Commercial Service Tools... 3 NOISE, VIBRATION
More informationSECTION 6 3 SERVICE PROCEDURES AND SPECIFICATIONS. Chassis
SERVICE PROCEDURES AND SPECIFICATIONS Chassis SECTION 6 3 Specifications........................................... 178 Checking clutch pedal freeplay............................ 180 Checking brake and
More informationHandout Activity: HA487
Tires HA487-2 Handout Activity: HA487 Tires Tires are mainly made from synthetic materials. They can be tubed or tubeless, with different types of construction, profile and speed ratings. The tire provides
More informationREAR SUSPENSION SECTION RSU CONTENTS E SUSPENSION RSU-1 RSU
REAR SUSPENSION E SUSPENSION SECTION RSU A REAR SUSPENSION B C D CONTENTS RSU PRECAUTIONS... 2 Cautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION AND
More informationTerminology for OTR TG 12PR 23.5 R NHS 16PR 45 / PR. Nominal Section Width Diameter (in)
Terminology for OTR Nominal Section Width Diameter (in) - Bias R Radial NHS - Non Highway Service TG - Tractor & Grader (Not for highway) 16.00-24 TG 12PR 23.5 R 25 14.00-24 NHS 16PR 45 / 65-45 38PR Nominal
More informationVehicle Level Steering and Suspension Alignment Service and Repair Wheel Alignment. Wheel Alignment
Page 1 of 7 2002 Dodge Truck Caravan FWD V6-3.3L VIN R Vehicle Level Steering and Suspension Alignment Service and Repair Wheel Alignment Wheel Alignment PRE-WHEEL ALIGNMENT INSPECTION Before any attempt
More information15 0 Date of Issue: Sept., ~ :H:OlVD.A. CB1000C N m ( kg-m, ft-ib) 4-7 N m ( kg-m, 3-5 ft-ib)
~ :H:OlVD.A. CB1000C 50-70 N m (5.0-7.0 kg-m, 36-51 ft-ib) 4-7 N m (0.4-0.7 kg-m, 3-5 ft-ib) 30-40 N m (3.0-4.0 kg-m, 22-29 ft-ib) 19-23 N m (1.9-2.3 kg-m, 14-17 ft-ib) 15-20 N m (1.5-2.0 kg-m, 11-14 ft-ib)
More informationFRONT SUSPENSION AND STEERING LINKAGE
A FRONT SUSPENSION AND STEERING LINKAGE CONTENTS GROUP 2 Page LOWER BALL JOINTS 12 LOWER CONTROL ARM AND SHAFT... 9 LOWER CONTROL ARM STRUT 12 PRE-ALIGNMENT INSPECTION Height Adjustment., 4 RUBBER ISOLATED
More information1. General Description
General Description 1. General Description A: SPECIFICATION Refer to FS section for rear suspension specifications. NOTE: Front and rear toe-in and front
More informationTires with inner tubes were used until the 50s. Inner tube tires
Tires Back in the day Way back in the day Pneumatic Tires Dunlop patented them for bicycles in 1888 Michelin put them on cars in 1895 Goodyear was started in 1898. Named after the inventor of vulcanized
More informationFRONT SUSPENSION GROUP CONTENTS GENERAL INFORMATION FASTENER TIGHTENING SPECIFICATIONS GENERAL SPECIFICATIONS...
33-1 GROUP 33 FRONT SUSPENSION CONTENTS GENERAL INFORMATION 33-2 FASTENER TIGHTENING SPECIFICATIONS 33-2 GENERAL SPECIFICATIONS 33-3 SERVICE SPECIFICATIONS 33-3 DIAGNOSIS 33-4 INTRODUCTION TO DIAGNOSIS
More informationOVERVIEW: This bulletin provides a diagnostic procedure for steering sensitivity.
NUMBER: GROUP: 19-002-01 REV. A Steering DATE: Sept. 28, 2001 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
More information2006 Hyundai Tiburon GT
Fig. 5: Identifying Clutch Cover & Disc Component With Torque Specifications REMOVAL 1. Drain the clutch fluid and transaxle gear oil. 2. Remove the transaxle assembly. 3. Insert the special tool (09411-25000)
More information