BRAKE INFORMATION FOR FKH AXLES
|
|
- Clifton West
- 5 years ago
- Views:
Transcription
1 BRAKE INFORMATION FOR FKH AXLES S-CAM ROTATION ON DRUM BRAKE AXLES It is our recommendation (it is also a general industry recommendation) to install Drum Brake Axles so that the S-Cams rotate in the same direction (when the brake is applied) as the wheels when travelling forward, as illustrated below. WHEEL ROTATION S-CAM ROTATION FORWARD Failure to comply with this recommendation by having the S-Cam rotating against the direction of the wheels when travelling forward (reversed S-Cams) may result in noisy brakes, premature wear of the brake linings and premature wear of the tyres. Installers can rotate the axle in order to position the camshafts and boosters away from obstructions such as the trailer frame or suspension components, provided the S-Cam rotational direction is not affected and complies with the recommendation in this bulletin. Uncontrolled document when printed! Bulletin No: KPM Rev4 1
2 INSTALLING THE BRAKE CHAMBERS (BOOSTER) The following information is for installing a FKH brand of double diaphragm spring brake chamber. 1. The FKH brake chamber is supplied with the push rod fully extended (NOT caged). 2. Depending on the brake force required (brake calculation), install the brake chamber in the appropriate bracket hole position. Nut torque lbft. Note: With the push rod fully extended and the brake chamber fitted to the correct mounting holes, the rod will line up with the correct hole in the slack adjuster, when the slack adjuster is at 90 to the push rod. 3. To cut the push rod to the correct length, start by marking the push rod in the fully extended position (no air applied / not caged) to the dimension in the table below. FKH Axle Model - axle tube size Booster rod cut length (mm) for slack adjuster setting of: KF21/22 Ø 127mm KF21/22 Ø 146mm KF21 sq 127mm KF37 Ø 127mm KK44 Ø 127mm N/A KF61/67/75/85-sq150mm Uncontrolled document when printed! Bulletin No: KPM Rev4 2
3 4. After the push rod is cut to the correct length, install the lock nut and clevis (as per photo ) and insert the clevis pin through the slack adjuster hole. 5. Now, follow the BRAKE ADJUSTMENT procedure on page To check the final installation; use the following table which contains the ideal dimensions with the booster and slack adjuster installed with the brakes applied. Axle Model and axle tube size Ideal booster to clevis pin dimension (mm) with brakes applied. KF21/22 Ø 127mm 246 KF21/22 Ø 146mm 222 KF21 sq 127mm 235 KF37 Ø 127mm 199 KK44 Ø 127mm 176 KF61/67/75/85-sq150mm Uncontrolled document when printed! Bulletin No: KPM Rev4 3
4 BRAKE ADJUSTMENT The following procedure must be followed after a new brake chamber or slack adjust has been installed or the brake needs adjusting for normal wear and tear: 1. Ensure that the correct specification brake actuator is fitted and that connection to the slack adjuster is in the correct position (refer to the trailer manufacturer s approved specification). 2. Make sure the trailer is on level ground, the wheels are chocked and the brakes are in the off position. 3. Adjust the free movement of the brake actuator push rod, tightening the slack adjuster to between Nm torque. Then back off the adjusting screw by two notches (1/4 turn). Free play of between 6 and 10mm on the slack adjuster is usually sufficient to provide proper clearance. 4. By applying the brake, check the stroke of the brake chamber push-rod at the slack adjuster for movement of approx. 35 to 40mm. 5. At the full applied brake operating pressure (650 kpa) the angle between the push-rod and the slack adjuster needs to be at Uncontrolled document when printed! Bulletin No: KPM Rev4 4
5 15 AXLE SLACK ADJUSTER INSTALLATION The slack adjuster adapters are fitted to the 15 axle to avoid any contact between the push rod and the axle tube. Note: Type 24/30 Brake Actuators are shown for illustrative purpose only. Brake actuator size is variable and is dependent on a number of factors, i.e. number of axles, load weight, air brake kit, suspension type, tyre size, etc. The actual brake actuator size is determined by the brake calculation, normally carried out by the trailer builder. Uncontrolled document when printed! Bulletin No: KPM Rev4 5
KI AIR SUSPENSION (wide Pivot Bush)
KI AIR SUSPENSION (wide Pivot Bush) Contents 1. Pre-assembly Considerations 2. Welding Instructions Chassis Connection 3. Tightening Instruction 4. Axle Alignment 5. Maintenance www.khitch.com.au Uncontrolled
More informationKI AIR SUSPENSION (narrow Pivot Bush)
KI AIR SUSPENSION (narrow Pivot Bush) Contents 1. Preassembly Considerations 2. Welding Instructions Chassis Connection 3. Tightening Instruction 4. Axle Alignment 5. Maintenance www.khitch.com.au Uncontrolled
More informationMAINTENANCE & SERVICE BULLETIN KT AIR SUSPENSION. Note: For parts identification go to the FKH Parts View Bulletin KPS on
KT AIR SUSPENSION KT 250 T KT 300 T KT 250 U KT 300 U Note: For parts identification go to the FKH Parts View Bulletin KPS-001-1112 on www.khitch.com.au Contents 1. Tightening Instruction 2. Pivot bolt
More informationUNITIZED WHEEL BEARING HUB
UNITIZED WHEEL BEARING HUB The FKH unitized wheel bearing hub is fitted with an SKF cartridge bearing unit. This bearing cartridge is sealed and is not serviceable (adjustable or grease able). While the
More informationINSTALLATION, MAINTENANCE & SERVICE BULLETIN KING PIN
KING PIN INSTALLATION for Bolt-on, Weld-in and Drop-in King Pin All: Installation and Maintenance procedure shall be strictly in accordance to AS/NZS 4968. 1, 2 and 3 (2003), VSP6 Section P and other statutory
More informationWeight approx. [kg] II39908FA BZ Part No. Type No. Type Push Rod Seal TÜV Inspection Report
Commercial Vehicle Systems Product DATA PD-403-200 Function This range of Brake Chambers is used on axles fitted with drum brakes. The single diaphragm cylinder provides the service brake function. In
More informationNHVIM Section 2 BASIC BRAKES MAINTENANCE
NHVIM Section 2 BASIC BRAKES MAINTENANCE Chair Lance Fisher, JLP Panel Members - Andrew Archibald, TMR Queensland - Renzo Barone, Meritor - Kevin Gibson, Knorr-Bremse Chair Lance Fisher, JLP Panel Members
More informationPARTS VIEW 22.5 DRUM BRAKE AXLE KF22 / KF29
DRUM BRAKE AXLE KF22 / KF29 KF29 Long Pin P brake, Page 6, E For CONMET wheel end part numbers go to page 5 www.khitch.com.au Uncontrolled document when printed Bulletin No: KPS-001-0912 Rev6 1 QUANTITY
More informationWeight Stroke TÜV-Inspection approx. [kg] II )4) BZ M16x Port threads:
Commercial Vehicle Systems Product DATA Spring Brakes (S-cam), diaphragm/piston Doc. No. Y1137 (EN - Rev. 5) September 216 PD-413-1 Function This range of Spring Brakes is used on axles fitted with drum
More informationOnce properly aligned weld axle saddles to axle using welding practice as below.
INSTALLATION & MAINTENANCE GUIDE 50 Series Suspensions Shackle bolts and rocker pivot bolts fitted with Nyloc type nuts must be tightened firmly allowing for rotational movement of bushed components. All
More informationPARTS VIEW KF22 / KF29 DRUM BRAKE AXLE (22.5 )
KF22 / KF29 DRUM BRAKE () See page 5 for: Weweler-MBS Ø146mm beam s-cam details. KF29 Long Pin P brake, Page 6, E For CONMET wheel end part numbers go to page 5 www.khitch.com.au Uncontrolled document
More informationMGM Brakes Service Manual
MGM Brakes Service Manual MAGNUM Performance Plus Spring Brake Actuators (MJ-Series 3.00 / 76mm Long Stroke ) For: S-Cam Tamper-Resistant MAGNUM Performance Plus Spring Brake Actuators Figure 1 A B C Your
More informationPARTS VIEW. See page 5 for: Weweler-MBS Ø146mm beam s-cam details.
KF22 & KF29 DRUM BRAKE () See page 5 for: Weweler-MBS Ø146mm beam s-cam details. KF29 Long Pin P brake, Page 6, E For ConMet wheel end part numbers go to page 5 www.khitch.com.au Uncontrolled document
More informationL Rev. 10/04. CSI Midland/Gunite Automatic Brake Adjuster Service Manual
L30006 Rev. 10/04 CSI Midland/Gunite Automatic Brake Adjuster Service Manual TABLE OF CONTENTS Overview...3 Installation Procedures...4 Brake Adjustment...10 Installation Procedures...11 Brake Adjustment...13
More informationMGM Brakes Service Manual
MGM Brakes Service Manual For: S-Cam Piston Type Service and Spring Brake Chambers Form No. 5009 Issued 6/91 - Revised 4/2010 MODEL MB-T SERIES MODEL MG-T SERIES Superseded by the MJS SERIES Form #5044
More informationINSTALLATION, MAINTENANCE & SERVICE BULLETIN. Use IM&S Bulletin KPM for the KA..A, KA..C, KA..D
5 th wheel KC..C The full range of FKH 5 th wheels Note: Use IM&S Bulletin KPM-007-0310 for the KA..A, KA..C, KA..D Use IM&S Bulletin KPM-007-0310 for the KH, KS, KD MODEL SERIES KA..A KA..C KA..D MODEL
More informationDATA PD BS7... Spring Brakes (Disc), diaphragm/diaphragm. Product. Function. Technical Features
Commercial Vehicle Systems Product DATA PD-415-200 Function This range of Spring Brakes is used on axles fitted with air disc brakes and provides the service and parking brake functions. The internal wind
More informationOperating and Installation Instruction. BPW Brake Components. BPW-EA-BK e - Version 2.0
Operating and Installation Instruction BPW Brake Components BPW-EA-BK 37401801e - Version 2.0 Page 2 BPW-EA-BK 37401801e BPW Trailer Disc Brake - ECO Disc - Installation instructions for vehicle manufacturers!!
More informationPARTS VIEW 22.5 DRUM BRAKE AXLE KF22 SERIES
PARTS VIEW DRUM BRAKE AXLE KF22 SERIES IMAGES FOR ILLUSTRATION PURPOSES ONLY www.khitch.com.au Bulletin No: KPS-001-0912-Rev02 1 QUANTITY PER AXLE PARTS VIEW DRUM BRAKE AXLE KF22 SERIES Ref No. PART No.
More informationBPW Trailer axle HZF ECO Plus
BPW Trailer axle HZF 900-5 ECO Plus L ( form closure ( square ) ) Brake SN 428 for ABS, with sensors Track 840 mm, Spring centre 950 mm, Booster bracket centre 4 mm for diaphragm cylinder, AGS ECO-Master,
More informationNATEF Task List - Medium/Heavy Duty Truck Brakes
The first task in is to listen to and verify the operator s concern, review past maintenance and repair documents, and determine necessary III. BRAKES A. Air 1 2 3 4 5 6 7 8 9 10 11 12 1. Air Supply and
More informationUNITIZED WHEEL BEARING HUB
UNITIZED WHEEL BEARING HUB The FKH unitized wheel bearing hub is fitted with a cartridge bearing unit. This bearing cartridge is sealed and is not serviceable (adjustable or grease able). While the unitized
More information5 th wheel KH, KS, KD
5 th wheel KH, KS, KD The full range of FKH 5 th wheels Note: Use IM&S Bulletin KPM-001-0915 for the KC..C Use IM&S Bulletin KPM-007-0310 for the KA..A, KA..C, KA..D MODEL SERIES KA..A KA..C KA..D MODEL
More informationFAST BRAKE INDEX. trouble-shooting guide
FAST BRAKE trouble-shooting guide INDEX INTRODUCTION 3 PRECAUTIONS 3 INSPECTION 4 Q&A Why does my spring brake have square air-inlet ports? 4 Why is the yoke welded to the service push-rod? 6 What do I
More informationGOLD LINE QUALITY PARTS
NEW www.goldlinequalityparts.com Includes Air Disc for Trucks, Tractors and Trailers RIGHT QUALITY RIGHT PRICE RIGHT AWAY www.goldlinequalityparts.com Edition 2017-10 powered by Tandem Drum DESIGNED FOR
More informationGUNITE Service Bulletin
Pinpointing Braking Failures Is It the Slack Adjuster? Or Is It the Foundation Brake? A slack adjuster - regardless if it s manual or automatic - is a lever used to actuate brakes. As its name implies,
More informationModule 6: Air Foundation Brakes
Air Brakes Terms and Definitions Basic Components That Make Up Air Foundation Brakes Types of Air Foundation Brakes Parts of a Cam Foundation Brake Parts of a Wedge Foundation Brake Parts of a Disc Foundation
More informationRecommended Brake Assembly/Disassembly Procedure
Recommended Brake Assembly/Disassembly Procedure Although Dexter Axle supplies non-asbestos brake linings as standard equipment, asbestos linings may still be found on axles in service.! CAUTION POTENTIAL
More informationProduct Customization Guide TSE Brakes, Inc.
Revision Date: June 7, 2018 Revision: 4 Page: 1 of 13 CONTENTS Brake Chamber Clamp Repositioning Instructions 2-3 Mechanical Release of Spring Brakes (Caging) 4-6 Installation Instructions 7-9 Determine
More informationAUTOMATIC SLACK ADJUSTER ECO MASTER
AUTOMATIC SLACK ADJUSTER ECO MASTER WORKING PRINCIPLE WORKING PRINCIPLE Braking process H E V Adjustment point SB Sequence of of the braking process H = Free stroke of the brake cylinder to cover the clearance
More informationPARTS VIEW PARTS KITS
PARTS KITS CONTENTS Page FKH AXLE ID SUMMARY 2 KF21 3-4 KF22 5-8 KF23 9 KF26 / KK26 10-11 KF37 12-13 KK44 14-15 KF61 16 KF75 17 KF85 18 FKH TURNTABLE ID SUMMARY 19-20 KA10A50 / KA12A50 21 KA10C50 / KA12C50
More informationPremium wheel-end brake products
Premium wheel-end brake products Spicer Automatic Slack Adjuster Service Manual Self Adjusting Brake Adjuster The description and specifications contained in this service publication are current at the
More informationChecking Your Brake Stroke Has Never Been This Easy!
See back for easy install instructions New! Visual Air Actuated Brake Stroke Indicator Works on any TSE OmniBrake 2.5" standard stroke 3030 Checking Your Brake Stroke Has Never Been This Easy! Easy to
More information5TH CATEGORY - HISTORIC RACING. GROUP Nb APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationCHAMBER CUSTOMIZATION GUIDE TSE
Revision Date: May 6, 2011 Revision: 3 Page: 1 of10 CONTENTS Brake Chamber Clamp Repositioning Instructions...2-3 Mechanical Release of Spring Brakes (Caging)...4-6 Determine The Correct Push Rod Length...7-9
More information1994 Mazda MX-5 Miata. BRAKE SYSTEM 1994 BRAKES Mazda - Disc & Drum BRAKES Mazda - Disc & Drum
BRAKE PEDAL FREE PLAY 1994 Mazda MX-5 Miata DESCRIPTION & OPERATION BRAKE SYSTEM 1994 BRAKES Mazda - Disc & Drum NOTE: For information on anti-lock brake systems, see ANTI-LOCK BRAKE SYSTEM article in
More informationPARTS LIST TRAILER BRAKE SYSTEMS. LIT NO: DATE: October 2017 REVISION: H
PARTS LIST TRAILER BRAKE SYSTEMS LIT NO: 97-097 DATE: October 07 REVISION: H TABLE OF CONTENTS INTRODUCTION ABBREVIATIONS DRUM BRAKES & 6. DRUM FOUNDATION BRAKE HXS Brakes P-TYPE DRUM FOUNDATION BRAKE
More informationD Class (Round Beam) E Class. K Class. Axle Range. Heavy Duty - High Speed Commercial Axle. High Speed Commercial Axle
s 2018 Range D Class (Round ) Heavy Duty - High Speed Commercial Features & benefits: Large high efficiency S-cam drum brakes: Ø406*120 & Ø420*180 Heavy duty axle beam: Ø127*16mm Commercial 10 Stud wheel
More informationASSEMBLY GUIDELINES AIR SUSPENSIONS. with Weld-on Axle Seats Series O/OM/OT
ASSEMBLY GUIDELINES AIR SUSPENSIONS with Weld-on Axle Seats Series O/OM/OT PW Air Suspensions are available for installation in either B single or multi-axle configurations. The axles are connected to
More informationKT AIR SUSPENSION (Engineering Lit. No. KL006)
KT AIR SUSPENSION (Engineering Lit. No. KL006) KT250 T KT300T KT250U KT300U Contents 1. Preassembly Considerations 2. KT Welding Instruction Axle Connection o Engineering LIT No: KL004 3. KT Welding Instruction
More informationAir Brake Inspection Presented By: G.L. May
Air Brake Inspection 2012 Presented By: G.L. May Outline of this course Objective of this course: The technician will have a better understanding of requirements for air drum brakes and air disc brakes
More informationBulletin No.: PRO Effective Date: 10/30/69 Cancels: N/A Page: 1 of 9
Technical Bulletin Bulletin No.: PRO-03-02 Effective Date: 10/30/69 Cancels: N/A Page: 1 of 9 Subject: 1970 FORD L SERIES MODEL DUAL AIR BRAKE SYSTEM The purpose of this bulletin is to generally familiarize
More informationHydraulic Fluid: Master Cylinder dia. [mm]
Commercial Vehicle Systems Product DATA Function This range of Brake Chambers with Master Cylinder is used to apply the service brakes on axles fitted with hydraulic brakes. The chamber applies force to
More informationTECHNICAL PROCEDURE INTRAAX SUSPENSION SYSTEMS TABLE OF CONTENTS
TECHNICAL PROCEDURE INTRAAX SUSPENSION SYSTEMS SUBJECT: Shock Mount Replacement Procedures LIT NO: L724 (Supersedes AM11 Rev B and L594 Rev C) DATE: December 1999 TABLE OF CONTENTS PREPARATION FOR PROCEDURES
More informationAs of July 2013 there are approximately fifteen Recovery Tow-Links are in service covering Komatsu 830E, 930E and 960E, Caterpillar 793 and 789, and H
RECOVERY TOW-LINK TRAILER 1.0 RECOVERY TOW-LINK SYSTEMS Loadquip is the manufacturing arm of CMP Engineers. Together the two companies have been supplying heavy mobile equipment solutions to the mining
More informationSD Bendix Manual Slack Adjusters DESCRIPTION ADJUSTING MECHANISM OPERATION
SD-05-1200 Bendix Manual Slack Adjusters WORM SHAFT (LOCK SCREW) FIGURE 1 - POSITIVE LOCK TYPE SLACK ADJUSTER DESCRIPTION In an s-cam type foundation brake, the final link between the pneumatic system
More informationASSEMBLY GUIDELINES AIR SUSPENSIONS. with Weld-on Axle Seats Series AL II
ASSEMBLY GUIDELINES AIR SUSPENSIONS with Weld-on Axle Seats Series AL II PW Air Suspensions are available for installation in either B single or multi-axle configurations. The axles are connected to the
More informationCam Brakes. Table of Contents
Sub-Headings Introduction 3 Q Plus 3 Disassembly 4 Remove the Wheel Components 4 Automatic Slack Adjuster 4 Brake Shoes 5 Remove Camshaft and Auto Slack Adjuster 6 Preparing Parts for Assembly 6 Clean
More informationBPW height-adjustable drawbars
Maintenance instructions ZAV BPW BERGISCHE ACHSEN BPW height-adjustable drawbars Series ZAV REPAIR, MAINTENANCE AND OPERATING INSTRUCTIONS Maintenance and Operating Instructions ZAV Table of contents:
More informationProduct Catalogue. Version 8.0. Section. FUWA Axle Components
Product Catalogue Section E Version 8.0 FUWA Section E Fuwa - Cam and Brake Assembly E:48 PRODUCT CATALOGUE 8.0 Fuwa - Cam and Brake Assembly Part List - 6 axle tube (square) - 5 axle tube (round) TL-11-427-800045
More informationUNITIZED WHEEL END MAINTENANCE
UNITIZED WHEEL END MAINTENANCE SCOPE SKF LUNAR ADH range consists of a cartridge (THU1) bearing unit. This bearing is permanently sealed and lubricated, and the bearing is not serviceable. While the LUNAR
More informationSlack Adjuster. Table of Contents
Slack Adjuster Table of Contents Sub-Headings Automatic Slack Adjuster Service 2 PayMaster Automatic Slack Adjuster 2 How the Automatic Slack Adjuster Works 2 Pressed-In, Sealed Actuator Boot 3 Handed
More informationS-ABA Service Manual. Self-Setting Automatic Brake Adjusters
S-ABA Service Manual Self-Setting Automatic Brake Adjusters Warning: Haldex strongly recommends routine visual checks be performed at EACH maintenance service interval. Foundation brake operational checks
More informationENGINE MECHANICAL (4A FE)
Maintenance, Engine Mechanical (4AFE) A3 Chassis Brake pads and disc Pad thickness Disc thickness Disc runout Brake linings and drums Lining thickness Drum inside diameter Front Rear Front Rear Drum brake
More informationService Manual Truck and Trailer Applications. AA1 Automatic Brake Adjusters
Service Manual Truck and Trailer Applications AA1 Automatic Brake Adjusters Table of Contents Operation... 1 Brake Adjuster Part Number and Build Date... 1 Steer Axle Applications... 2 Drive Axle Applications...
More informationL LL. Workshop manual. BPW steering axles. BPW-WH-LL-L e
L LL Workshop manual BPW steering axles BPW-WH-LL-L 35351701e Page 2 BPW-WH-LL-L 35351701e Valid: 01.02.2017 Subject to change without notice. Current versions and additional information can be found online
More information5TH CATEGORY - HISTORIC RACING. GROUP Nc APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nc APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationAir Brake Adjustment. What You ll Learn After reading this chapter you will be able to:
8 Air Brake Adjustment Fast Fact Your company may have a maintenance crew to keep vehicles safely running. But one person alone is ultimately responsible to ensure that the brakes are operating properly
More informationAPPLICATION TO BUILD A CAMS DEDICATED RALLY CAR
www.dtei.sa.gov.au ABN: 92 366 288 135 MR 639 03/08 1. ABOUT YOU LODGEMENT INFORMATION In person: Department for Transport, Energy and Infrastructure, Kateena Street, Regency Park SA 5010 By post: Vehicle
More informationA 1 SERVICE SPECIFICATIONS
A1 A2 Clutch CLUTCH Specifications Pedal height (from asphalt sheet) Release point (from pedal stroke end position) Push rod play at pedal top Pedal freeplay Disc rivet head depth Disc runout Diaphragm
More informationSECTION 1 - CHASSIS 1.1 CHASSIS FRAME
5TH CATEGORY - HISTORIC RACING GROUP Nb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationROR Trailer Products Axle & Brake Parts List LM and LC Series Axles including disc and drum brake variants
ROR Trailer Products Axle & Brake Parts List LM and LC Series Axles including disc and drum brake variants LM/LC Hub Assembly 14 1 3 10 9 19 20 8 5 6 7 11 1 4 2 18 16 13 17 15 13 12 2 LM/LC Hub Assembly
More informationMaintenance and Repair Manual Axle types SK RS / RZ 9042 SK RS / RZ SK RS / RZ 9037 SK RS / RZ 11037
Maintenance and Repair Manual Axle types SK RS / RZ 9042 SK RS / RZ 11242 SK RS / RZ 9037 SK RS / RZ 11037 Edition 02/02/2006 Service Vehicle information Manufacturer... Address... Body type... Chassis
More informationTechnical specification. Electric cold milling machine W 350 E
Technical specification Electric cold milling machine W 350 E Technical specification Milling width max. Milling depth* 1 Milling drum Tool spacing Electric cold milling machine W 350 E 350 mm 0 100 mm
More informationParking brake Mechanical brake acting on rear wheels
11 Brake System 11.1 General SPECIFICATIONS EJTC0010 Master cylinder Type Tandem type I.D. mm(in.) 20.64 mm (0.813 in.) Fluid level warning sensor Provided Brake booster Type Vacuum Boosting ratio 4.0
More informationMERITOR ALLFIT CLEARANCE-SENSING AUTOMATIC SLACK ADJUSTERS COMPLETE PORTFOLIO TO MEET EVERY APPLICATION AND BUDGET.
MERITOR ALLFIT CLEARANCE-SENSING AUTOMATIC SLACK ADJUSTERS COMPLETE PORTFOLIO TO MEET EVERY APPLICATION AND BUDGET. SMART ASA CHOICES FROM MERITOR. YOUR TRUSTED SOLUTIONS PROVIDER. As a leading supplier
More information5TH CATEGORY - HISTORIC RACING. GROUP Nc APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nc APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationTHE NETHERLANDS (N E D E R L A N D) ECE R13, Annex 11 Appendix 3 Test report as prescribed in Paragraphs and of Appendix 2 to this Annex
Vehicle Technology Division THE NETHERLANDS (N E D E R L A N D) ECE R13, Annex 11 Appendix 3 Test report as prescribed in Paragraphs 3.7.1. and 3.7.2. of Appendix 2 to this Annex Test report number: RDW
More informationPowers Controls No. 6 Pneumatic Damper Actuator
Document No. 152-013P25 Powers Controls No. 6 Pneumatic Damper Actuator OEM Literature Basic Actuator Typical Actuator with Clevis and Pin Actuator with Extended Shaft and Frame Mounting Accessories Description
More information55-64 Full Size Chevy
55-64 Full Size Chevy Installation Instructions Power Disc Conversion 9 slimline booster pictured Your new disc brake conversion kit can be bolted up with standard hand tools. The only tools you may not
More informationDIAGNOSIS AND TESTING
2007 Ford F650 : Brakes > Air Brake System General Information > DIAGNOSIS AND TESTING DIAGNOSIS AND TESTING Listen SECTION 206 00B: Brake System General Information Air 2007 F Super Duty 650 750 Workshop
More informationBendix Air Disc Brake Chamber Service Information
Bendix Air Disc Brake Chamber Service Information As fleets continue to experience the advantages of Bendix Air Disc Brakes and the number of vehicles with this technology grows, there is an increasing
More informationSuperTrac. Axle. Service & Maintenance. Manual
SuperTrac Axle Service & Maintenance Manual Table of Contents Page Exploded Views Section 1: General Information General Warnings Description of Axle Models Identifications Section 2: Installation Axle
More informationTechnical Procedure. SUBJECT: Operation, Maintenance and Retrofit Procedures. DATE: February 2018
Technical Procedure Trailer Suspension Systems QUIK-DRAW SUBJECT: Operation, Maintenance and Retrofit Procedures LIT NO: L738 DATE: February 2018 REVISION: C Van Applications (HK Series, VANTRAAX and ULTRAA-K
More informationH K N. Workshop manual. BPW trailer axles with drum brakes. BPW-WH-HKN e
H K N Workshop manual BPW trailer axles with drum brakes BPW-WH-HKN 35191601e Page 2 BPW-WH-HKN 35191601e BPW trailer axles with drum brake S-camshaft SN 420 / SN 360 / SN 300 ECO Plus 3, ECO Plus 2, ECO
More information5TH CATEGORY - HISTORIC RACING. GROUP Sb APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Sb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationPart II NORTH AMERICAN STANDARD VEHICLE OUT-OF-SERVICE CRITERIA POLICY STATEMENT
Part II NORTH AMERICAN STANDARD VEHICLE OUT-OF-SERVICE CRITERIA POLICY STATEMENT The purpose of this part is to identify Critical Vehicle Inspection Items and provide criteria for declaring vehicles out-of-service
More information5TH CATEGORY - HISTORIC RACING. GROUP Sb APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Sb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationSetting the Standards Trailer Component Suppliers Perspective
Setting the Standards Trailer Component Suppliers Perspective Mario Colosimo BPW Historical Perspective For many years trailers had to be cheap to buy, with little consideration to whole of life costs.
More informationPRODUCT USE INFORMATION
921654300 Thank you for choosing Rough Country for your suspension needs. *65430BAG1* 65430BAG1 JEEP JL 3.5 Control Arm Drop Suspension Kit Rough Country recommends a certified technician install this
More informationSERVICE BULLETIN No. 1088
SERVICE BULLETIN No. 1088 Circulate to listed addressees COACH MODEL BULLETIN TYPE MANUAL & SECTION : T800 Series; T900 Series; T 2100 Series; C2045 : Service Information : Maintenance Manual: Chapter
More informationMERITOR MEDIUM DUTY FRONT-DRIVE STEER AXLES MX-120, MX-120 HR AND MX-120-EVO SERIES PB-02167
MERITOR MEDIUM DUTY FRONT-DRIVE STEER AXLES MX-120, MX-120 HR AND MX-120-EVO SERIES PB-02167 Meritor.com/lod With a user-friendly approach and visually appealing format for easier, quicker surfing, Literature
More information5TH CATEGORY - HISTORIC RACING. GROUP Nc APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nc APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationInstalling RideSentry Suspension Axle Seats onto RideStar RHP Series Single-Axle and Sliding Tandem Trailer Air Suspension Systems
Issued 10-07 Technical Bulletin Installing RideSentry Suspension Axle Seats onto RideStar RHP Series Single-Axle and Sliding Tandem Trailer Air Suspension Systems Issued 1 Technical 10-07 Bulletin Hazard
More informationMS2200, MS2500, and MS3000 Suspension Installation Manual ON/OFF HIGHWAY SUSPENSION SYSTEM
MS22, MS25, and MS3 Suspension Installation Manual ON/OFF HIGHWAY SUSPENSION SYSTEM 972.547.62 8.445.736 FAX: 972.542.97 725 E. UNIVERSITY ST. McKINNEY, TEXAS 7569 www.watsonsuspensions.com Watson & Chalin
More informationWAP disc brake technology. Assembly, operating and maintenance instructions
WAP disc brake technology Assembly, operating and maintenance instructions Number MA-025 Date 22.07.2010 1 Please read this operating and service manual before starting the vehicle. It forms part of the
More informationSPECIFICATIONS ORDER GUIDE SERVICE KITS AND PARTS
SPECIFICATIONS ORDER GUIDE SERVICE KITS AND PARTS 10K Auxiliary Suspension 10,000 LBS. CAPACITY Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 www.linkmfg.com QUESTIONS? CALL CUSTOMER
More informationBPW Special tools and calibration equipment. for BPW axles and axle suspensions. BPW-WP e
BPW Special tools and calibration equipment for BPW axles and axle suspensions BPW-WP 39381701e BPW-WP 39381701e Your partner on the path to economic viability BPW Bergische Achsen Kommanditgesellschaft
More informationBRAKE SYSTEM Article Text 1996 Toyota RAV4 For Copyright 1998 Mitchell Repair Information Company, LLC Wednesday, September 13, :30PM
Article Text ARTICLE BEGINNING 1996 BRAKES Toyota - Disc & Drum RAV4 * PLEASE READ THIS FIRST * WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see
More informationMaintenance and Repair Manual SK RS SK 500 plus
Maintenance and Repair Manual SK RS 9042 - SK 500 plus Edition 01/2006 Service Vehicle information Manufacturer... Address... Body type... Chassis no... Year of manufacture... Registration, date-in-service...
More informationCAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT
Page 1 of 45 CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Special Tools J 45027 Tensioner Tool J 45059 Angle Meter Page 2 of 45 Removal Procedure Page 3 of 45 Page 4 of 45 Page 5 of 45 Fig.
More informationFig. 1: Throttle valve measurement 1.2L carbureted
ADJUSTMENTS Automatic Choke Mechanism Fig. 1: Throttle valve measurement 1.2L carbureted engine Fig. 2: Throttle valve measurement 1.6L and 1.8L carbureted engines 1 of 8 6/21/2006 12:10 PM 1. 2. 3. 4.
More informationTECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS The information shown is based on data available at the time of publication (June, 2006). Body and Chassis Five-seater, four-door sedan, all-steel unitary body chassis. Choice
More informationMaintenance and Repair Manual SK RS SK 1000 ET 0
Maintenance and Repair Manual SK RS 9042 - SK 1000 ET 0 Edition 01/2006 Service Vehicle information Manufacturer... Address... Body type... Chassis no... Year of manufacture... Registration, date-in-service...
More informationHP10253 KIT Ford F-150 2WD / 4WD 2" Leveling Kit
HP10253 KIT 2004-2017 Ford F-150 2WD / 4WD 2" Leveling Kit KIT CONTENT A B C KIT CONTENTS A Upper Strut Spacer (2) B M10 x 1.5 Flange Nut (6) C M10 x 1.5 x 40 mm Socket Head Cap Screw (6) Make sure all
More informationAxle Components. 12,000 lbs. Capacity
12,000 lbs. Heavy Duty Components 27-358 Unitized Oil Seal - disc or drum (Dimensions are 3.125 x 4.506 x.605) 2 010-056-00 27-342 3984 Inner Bearing (Inside diameter 2.625 ) 3 031-020-02 27-343 3920 Inner
More informationOverview. Trailing arm 100 mm wide. Single leaf 1x57. Single leaf 1x57
Overview Sheet I Air suspension axles and suspensions Axle load Trailing arm 100 mm wide Air bag Axle type with disc brake TSB 4312 Ride height FH (mm) to drawing Single leaf 1x57 415-560 Sheet 1a Air
More informationSYSTEM 180 AS 90. > The loader specialist. > Swing Shovel Loader m 3
> The loader specialist > Swing Shovel Loader 0.9 1.4 m 3 Let s have a look Tipping loads with standard bucket Working area with 4-in-1 bucket 53.5 kw / 73 hp at 2500 min -1 3.240 kg 100% 80 100% max.
More informationPREVOST AIR SYSTEMS WHAT THEY DO AND HOW THEY DO IT
PREVOST AIR SYSTEMS WHAT THEY DO AND HOW THEY DO IT Air. In our buses we use air for many purposes. We warm ourselves and cool ourselves with it. We supply it to our engines so they will run. Air is what
More informationTechnical specification. Cold milling machine W 35
Technical specification Cold milling machine W 35 Technical specification Milling width max. Milling depth * 1 Milling drum Tool spacing Cold milling machine W 35 14 350 mm 0 2 0 60 mm 1 /2 12 mm Number
More information