Universal Automatic Non-Conductive Fluid Regulator

Size: px
Start display at page:

Download "Universal Automatic Non-Conductive Fluid Regulator"

Transcription

1 Universal Automatic Non-Conductive Fluid Regulator Customer Product Manual Part Issued 3/18 NORDSON CORPORATION AMHERST, OHIO USA

2 Table of Contents tents Safety... 1 Qualified Personnel... 1 Intended Use... 1 Regulations and Approvals... 1 Personal Safety... 2 High-Pressure Fluids... 2 Fire Safety... 3 Halogenated Hydrocarbon Solvent Hazards. 4 Action in the Event of a Malfunction... 4 Disposal... 4 Description... 5 Installation... 6 Mounting Kits... 6 Kinetix Spray Gun Mounting Kit... 6 Two-Inch Gun Bar Mounting Kit... 7 One-Inch Gun Bar Mounting Kit... 8 Air and Fluid Connections... 9 Operation Flushing Troubleshooting Repair Disassembly Service Notes Assembly Parts Regulator Parts Adhesives and Lubricants Ball Stem and Seat Kit Rebuild Kit Mounting Kits Kinetix Spray Gun Mounting Kit in. Universal Gun Bar Mounting Kit in. Universal Gun Bar Mounting Kit Recommended Spare Parts Specifications Contact Us Nordson Corporation welcomes requests for information, comments, and inquiries about its products. General information about Nordson can be found on the Internet using the following address: Address all correspondence to: Nordson Corporation Attn: Customer Service 300 Nordson Drive Amherst, OH Notice This is a Nordson Corporation publication which is protected by copyright. Original copyright date No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Nordson Corporation. The information contained in this publication is subject to change without notice. Trademarks Kinetix, Nordson, and the Nordson logo are registered trademarks of Nordson Corporation. Delrin and Mylar are registered trademarks of E. I. DuPont de Nemours and Company. Loctite is a registered trademark of Henkel Loctite Corporation Nordson Corporation

3 Change Record i Revision Date Change 04 3/18 Changed part number to Change Record 2018 Nordson Corporation

4 ii Change Record 2018 Nordson Corporation

5 Universal Automatic Non-Conductive Fluid Regulator 1 Universal Automatic Non-Conductive Fluid Regulator Safety Read and follow these safety instructions. Task- and equipment-specific warnings, cautions, and instructions are included in equipment documentation where appropriate. Make sure all equipment documentation, including these instructions, is accessible to persons operating or servicing equipment. Qualified Personnel Equipment owners are responsible for making sure that Nordson equipment is installed, operated, and serviced by qualified personnel. Qualified personnel are those employees or contractors who are trained to safely perform their assigned tasks. They are familiar with all relevant safety rules and regulations and are physically capable of performing their assigned tasks. Intended Use Use of Nordson equipment in ways other than those described in the documentation supplied with the equipment may result in injury to persons or damage to property. Some examples of unintended use of equipment include using incompatible materials making unauthorized modifications removing or bypassing safety guards or interlocks using incompatible or damaged parts using unapproved auxiliary equipment operating equipment in excess of maximum ratings Regulations and Approvals Make sure all equipment is rated and approved for the environment in which it is used. Any approvals obtained for Nordson equipment will be voided if instructions for installation, operation, and service are not followed Nordson Corporation

6 2 Universal Automatic Non-Conductive Fluid Regulator Personal Safety To prevent injury follow these instructions. Do not operate or service equipment unless you are qualified. Do not operate equipment unless safety guards, doors, or covers are intact and automatic interlocks are operating properly. Do not bypass or disarm any safety devices. Keep clear of moving equipment. Before adjusting or servicing moving equipment, shut off the power supply and wait until the equipment comes to a complete stop. Lock out power and secure the equipment to prevent unexpected movement. Relieve (bleed off) hydraulic and pneumatic pressure before adjusting or servicing pressurized systems or components. Disconnect, lock out, and tag switches before servicing electrical equipment. While operating manual spray guns, make sure you are grounded. Wear electrically conductive gloves or a grounding strap connected to the gun handle or other true earth ground. Do not wear or carry metallic objects such as jewelry or tools. If you receive even a slight electrical shock, shut down all electrical or electrostatic equipment immediately. Do not restart the equipment until the problem has been identified and corrected. Obtain and read Material Safety Data Sheets (MSDS) for all materials used. Follow the manufacturer s instructions for safe handling and use of materials, and use recommended personal protection devices. Make sure the spray area is adequately ventilated. To prevent injury, be aware of less-obvious dangers in the workplace that often cannot be completely eliminated, such as hot surfaces, sharp edges, energized electrical circuits, and moving parts that cannot be enclosed or otherwise guarded for practical reasons. High-Pressure Fluids High-pressure fluids, unless they are safely contained, are extremely hazardous. Always relieve fluid pressure before adjusting or servicing high pressure equipment. A jet of high-pressure fluid can cut like a knife and cause serious bodily injury, amputation, or death. Fluids penetrating the skin can also cause toxic poisoning. If you suffer a fluid injection injury, seek medical care immediately. If possible, provide a copy of the MSDS for the injected fluid to the health care provider. The National Spray Equipment Manufacturers Association has created a wallet card that you should carry when you are operating high-pressure spray equipment. These cards are supplied with your equipment. The following is the text of this card: 2018 Nordson Corporation

7 Universal Automatic Non-Conductive Fluid Regulator 3 WARNING: Any injury caused by high pressure liquid can be serious. If you are injured or even suspect an injury: Go to an emergency room immediately. Tell the doctor that you suspect an injection injury. Show them this card Tell them what kind of material you were spraying MEDICAL ALERT AIRLESS SPRAY WOUNDS: NOTE TO PHYSICIAN Injection in the skin is a serious traumatic injury. It is important to treat the injury surgically as soon as possible. Do not delay treatment to research toxicity. Toxicity is a concern with some exotic coatings injected directly into the bloodstream. Consultation with a plastic surgeon or a reconstructive hand surgeon may be advisable. The seriousness of the wound depends on where the injury is on the body, whether the substance hit something on its way in and deflected causing more damage, and many other variables including skin microflora residing in the paint or gun which are blasted into the wound. If the injected paint contains acrylic latex and titanium dioxide that damage the tissue s resistance to infection, bacterial growth will flourish. The treatment that doctors recommend for an injection injury to the hand includes immediate decompression of the closed vascular compartments of the hand to release the underlying tissue distended by the injected paint, judicious wound debridement, and immediate antibiotic treatment. Fire Safety To avoid a fire or explosion, follow these instructions. Ground all conductive equipment. Use only grounded air and fluid hoses. Check equipment and workpiece grounding devices regularly. Resistance to ground must not exceed one megohm. Shut down all equipment immediately if you notice static sparking or arcing. Do not restart the equipment until the cause has been identified and corrected. Do not smoke, weld, grind, or use open flames where flammable materials are being used or stored. Do not heat materials to temperatures above those recommended by the manufacturer. Make sure heat monitoring and limiting devices are working properly. Provide adequate ventilation to prevent dangerous concentrations of volatile particles or vapors. Refer to local codes or your material MSDS for guidance. Do not disconnect live electrical circuits when working with flammable materials. Shut off power at a disconnect switch first to prevent sparking Nordson Corporation

8 4 Universal Automatic Non-Conductive Fluid Regulator Know where emergency stop buttons, shutoff valves, and fire extinguishers are located. If a fire starts in a spray booth, immediately shut off the spray system and exhaust fans. Shut off electrostatic power and ground the charging system before adjusting, cleaning, or repairing electrostatic equipment. Clean, maintain, test, and repair equipment according to the instructions in your equipment documentation. Use only replacement parts that are designed for use with original equipment. Contact your Nordson representative for parts information and advice. Halogenated Hydrocarbon Solvent Hazards Do not use halogenated hydrocarbon solvents in a pressurized system that contains aluminum components. Under pressure, these solvents can react with aluminum and explode, causing injury, death, or property damage. Halogenated hydrocarbon solvents contain one or more of the following elements: Element Symbol Prefix Fluorine F Fluoro- Chlorine Cl Chloro- Bromine Br Bromo- Iodine I Iodo- Check your material MSDS or contact your material supplier for more information. If you must use halogenated hydrocarbon solvents, contact your Nordson representative for information about compatible Nordson components. Action in the Event of a Malfunction If a system or any equipment in a system malfunctions, shut off the system immediately and perform the following steps: Disconnect and lock out system electrical power. Close hydraulic and pneumatic shutoff valves and relieve pressures. Identify the reason for the malfunction and correct it before restarting the system. Disposal Dispose of equipment and materials used in operation and servicing according to local codes Nordson Corporation

9 Universal Automatic Non-Conductive Fluid Regulator 5 Description See Figure 1. The universal automatic non-conductive fluid regulator provides accurate, positive fluid pressure control to spray guns, dispensing valves, or atomizing heads. The regulator is electrically non-conductive and uses low-pressure air to operate. The regulator is installed at circulating line take-offs or with pumps. It is used to reduce main line pressure and maintain the desired fluid pressure to the spray gun or atomizing head. The regulator is designed for both circulating and non-circulating systems. In a circulating system, the fluid circulates through the regulator body through the two ports (in one port and out the other). In a non-circulating system, a 3 / 8 -in. NPTF plug is installed in one of the fluid ports. Two types of mounting kits are available for the regulator. The spray gun mounting kit allows you to mount the regulator onto the back of an automatic Kinetix spray gun. The gun bar mounting kits allow you to mount the regulator remotely for use with a variety of automatic spray guns. Figure 1 Universal Automatic Non-Conductive Fluid Regulator 2018 Nordson Corporation

10 6 Universal Automatic Non-Conductive Fluid Regulator Installation WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. WARNING: System or material pressurized. Relieve pressure before opening. Failure to observe may result in serious burns. Mounting Kits There are three mounting kits available for the universal regulator. Follow these procedures to install them with your regulator. Kinetix Spray Gun Mounting Kit 1. See Figure 2. Slide the collar (1) over the back of the Kinetix automatic spray gun. 2. Tighten the set screw (3) with a 5 / 32 -in. hex key. 3. Tighten the upper jam nut (2) against the collar. 4. Thread the set screw into the mounting hole (4) in the regulator five six turns, positioning the regulator as shown. 5. Tighten the lower jam nut (2) against the regulator Figure 2 Kinetix Spray Gun Mounting Kit 1. Collar 2. Jam nuts 3. Set screw 4. Mounting hole 2018 Nordson Corporation

11 Universal Automatic Non-Conductive Fluid Regulator 7 Two-Inch Gun Bar Mounting Kit 1. Remove the two screws (1), lock washers (2), and flat washers (3) from the split collars (4, 5). 2. Position the split collars in the desired location on the spray gun mounting bar. NOTE: The half of the split collar (5) with the 5 / UNC threaded hole must be placed on the bottom of the spray gun mounting bar. 3. Secure the split collar to the spray gun mounting bar with the screws and washers you removed earlier. 4. Screw the set screw (6) into the split collar with a 5 / 32 -in. hex key. 5. Tighten the upper jam nut (7) against the split collar. 6. Thread the regulator onto the set screw to the desired position. 7. Tighten the lower jam nut (7) against the regulator Figure 3 Gun Bar Mounting Kit 1. Screws 2. Lock washers 3. Flat washers 4. Split collar 5. Split collar (with 5 / UNC threaded hole) 6. Set screw 7. Jam nuts 2018 Nordson Corporation

12 8 Universal Automatic Non-Conductive Fluid Regulator One-Inch Gun Bar Mounting Kit 1. Remove the two screws (1) from the split collar (2). 2. Position the split collar in the desired location on the spray gun mounting bar. NOTE: The half of the split collar (2) with the 5 / UNC threaded hole must be placed on the bottom of the spray gun mounting bar. 3. Secure the split collar to the spray gun mounting bar with the screws (1). 4. Screw the set screw (4) into the split collar with a 5 / 32 -in. hex key. 5. Tighten the upper jam nut (3) against the split collar. 6. Thread the regulator onto the set screw to the desired position. 7. Tighten the lower jam nut (3) against the regulator Figure 4 Gun Bar Mounting Kit 1. Screws 2. Split collar 3. Jam nuts 4. Set screw 2018 Nordson Corporation

13 Universal Automatic Non-Conductive Fluid Regulator 9 Air and Fluid Connections WARNING: Do not substitute the fittings furnished with this regulator with any other plastic or metal fittings. Sparking caused by non-grounded metal fittings or by electrostatic breakdown resulting in the pin holing of plastic fittings may cause fire or explosion. Refer to your spray gun manual for proper fluid inlet fittings. NOTE: An anti-backflow device should be used on the pilot air line. See Figure Circulating Systems: Remove the 3 / 8 -in. NPT plug (6) from the inlet (5). Non-Circulating Systems: Leave the 3 / 8 -in. NPT plug (6) in the inlet (5). 2. Install fittings in the outlet (2), fluid supply inlet (4), and the circulating inlet (5), if applicable. Refer to Recommended Spare Parts on page 18 for fitting part numbers and ordering information. 3. Connect the fluid supply line to the inlet fitting. 4. Circulating Systems: Connect a return line from the circulating inlet fitting back to the fluid supply. 5. Connect the gun fluid supply line to the outlet fitting. 6. Connect a 1 / 4 -in. air supply line to the pilot air connector (3) Figure 5 Regulator Installation 1. Mounting hole 2. Outlet (gun fluid supply line) 3. Pilot air connector 4. Fluid supply inlet 5. Circulating inlet 6. 3 / 8 -in. NPT plug 2018 Nordson Corporation

14 10 Universal Automatic Non-Conductive Fluid Regulator Operation WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Clean and test the system thoroughly before admitting fluid to the regulator. This avoids contaminants from clogging or damaging the regulator. NOTE: Always use the lowest possible air and fluid pressures for your application. High pressures cause premature spray nozzle and pump wear. 1. Partially relieve pressure in the spray gun fluid supply hose to make sure the gauge reading is correct, before reducing the regulator pressure. 2. Use an air regulator with at least 51-mm (2-in.) diameter diaphragm to control the fluid regulator. 3. Apply air pressure to the pilot air fitting in the regulator base. NOTE: To increase fluid pressure, increase the input air pressure. The output fluid pressure is remotely regulated by input air pressure controls. Flushing Flush frequently after installation and between system operation. 1. Use a compatible solvent whenever the rest of the system is flushed. 2. Flush until thoroughly clean. NOTE: Always use the lowest possible pressure when flushing Nordson Corporation

15 Universal Automatic Non-Conductive Fluid Regulator 11 Troubleshooting WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. These procedures cover only the most common problems that you may encounter. If you cannot solve the problem with the information given here, contact your local Nordson representative for help. WARNING: System or material pressurized. Relieve pressure before opening. Failure to observe may result in serious burns. NOTE: Check all suggested corrective actions in the troubleshooting chart before disassembling the regulator. 1. No pressure regulation Problem Possible Cause Corrective Action 2. Pressure increases above setting 3. Pressure drops below setting Damaged or clogged air regulator or line Damaged diaphragm Damaged or clogged air regulator or line Damaged diaphragm Seat is leaking Damaged or clogged air regulator or line Empty or clogged fluid supply line Clogged spray gun or fluid dispensing valve Regulator used above the rated flow capacity Clear the obstruction in the line. Repair the regulator if necessary. Replace the diaphragm. Clear the obstruction in the line. Repair the regulator if necessary. Replace the diaphragm. Replace the seat gasket, seat, and stem. Clear the obstruction in the line. Repair the regulator if necessary. Refill or flush the supply line. Refer to the spray gun or valve manual for repair and maintenance instruction. Use additional regulators, refer to Specifications on page 18 for ratings Nordson Corporation

16 12 Universal Automatic Non-Conductive Fluid Regulator Repair WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. WARNING: System or material pressurized. Relieve pressure before opening. Failure to observe may result in serious burns. Before performing any repair procedures on the universal automatic non-conductive regulator, shut off the pump, release all air and fluid pressure in the regulator, and disconnect the air and fluid lines. NOTE: The numeric callouts in this section match the item numbers in the regulator s parts list. Refer to Parts on page 15 for complete part descriptions and ordering information. Disassembly See Figure Unscrew the seat retainer (1) from the top of the bonnet (7). Inspect the O-ring (2) installed on the retainer and replace it if necessary. 2. Apply 1.4 bar (20 psi) air pressure to the pilot air connector (13) to push up the diaphragm. NOTE: Handle the stem and seat (3A, 3B) with care. 3. Unscrew the stem (3A) from the body stem (8) within the bonnet. 4. Remove the seat gasket (5) and seat (3B) from the top of the regulator bonnet. Be careful not to lose the seat gasket. 5. Remove the air pressure from the pilot air connector. 6. Remove the pipe plug (4) from the regulator base. Remove the old PTFE tape from the parts. 7. Unscrew the cap screw (16) from the body stem. Remove and separate the cap screw, flat washer (17), spacer tube (15) and compression spring (14) from the regulator. 8. Remove the spacer plug (12) from the regulator base. 9. Unscrew the regulator base from the bonnet. 10. Remove the body stem, diaphragm (9), and nut (10) assembly from the bonnet. Separate these three parts using the tool supplied with the regulator. 11. Remove the O-ring (7A) from the bonnet. 12. Clean all parts as necessary Nordson Corporation

17 Universal Automatic Non-Conductive Fluid Regulator B PTFE Side Rubber Side A A Figure 6 Repair 1. Seat retainer 2. O-ring 3A. Stem 3B. Seat 4. Pipe plug 5. Seat gasket 6. Plug 7. Bonnet 7A. O-ring 8. Body stem 9. Diaphragm 10. Nut 11. Regulator base 12. Spacer plug 13. Pilot air connector 14. Compression spring 15. Spacer tube 16. Cap screw 17. Flat washer Service Notes Use these service notes to rebuild the regulator correctly. Do not overtighten the noted items. Note Item Description 2, 9 Apply O-ring lubricant to these parts , 18 Apply PTFE tape to the threads of these parts , 16 Apply threadlocking adhesive to the threads of these parts. 11 Tighten the regulator base to 13.6 Nm (120 in.-lb). 1 Tighten the seat retainer to Nm (40 50 in.-lb) Tighten the cap screw to Nm (55 65 in.-oz). 7 3A, 3B Tighten the stem to Nm (70 80 in.-oz). The stem and seat are a matched set and are sold as one part Nordson Corporation

18 14 Universal Automatic Non-Conductive Fluid Regulator Assembly 1. See Figure 6. Apply O-ring lubricant to the outer ring on the rubber side of the diaphragm (9). 2. Assemble the body stem (8), diaphragm, and nut (10) and tighten the assembly with the tool supplied with the regulator until the body stem stops rotating. 3. Install the O-ring (7A) into the bonnet. 4. Insert the diaphragm assembly into the regulator bonnet (7) with the PTFE side of the diaphragm facing towards the fluid inlet. 5. Screw the regulator base (11) into the bonnet and tighten it to 13.6 Nm (120 in.-lb). 6. Insert the spacer plug (12) into the regulator base. 7. Apply threadlocking adhesive to the threads of the cap screw (16) then assemble the flat washer (17), spacer tube (15), and compression spring (14) on the cap screw. Screw this assembly through the regulator base into the body stem. Tighten the cap screw to Nm (55 65 in.-oz). 8. Apply PTFE tape to the pipe plug (4) and install flush to one thread above the base. 9. Set the seat gasket (5) into the top of the regulator bonnet. 10. Install the stem and seat assembly: a. Insert the stem (3A) into the chamfered end of the seat (3B). b. Apply Loctite threadlocking adhesive to the threads of the valve stem. c. Apply 1.4 bar (20 psi) air pressure to the pilot air connector (13) in the regulator base to push up the diaphragm. d. While the diaphragm is being pushed up, screw the valve stem into the top of the bonnet and into the body stem. Tighten the valve stem to Nm (70 80 in.-oz). e. Remove the air pressure from the pilot air connector. 11. Apply O-ring lubricant to the O-ring (2) and install on the seat retainer (1). Screw the seat retainer into the bonnet and tighten it to Nm (40 50 in.-lb) Nordson Corporation

19 Universal Automatic Non-Conductive Fluid Regulator 15 Parts To order parts, call the Nordson Finishing Customer Support Center at (800) or contact your local Nordson representative. Regulator Parts See Figure 7. NOTE: Before ordering parts for your regulator, review Repair in this manual to make sure you are ordering the correct parts, lubricants, and adhesives. Item Part Description Quantity Note REGULATOR, low-pressure, universal RETAINER, ball seat, regulator O-RING, PTFE, in. ID x x 0.06 in. 1 A STEM and seat assembly 1 A, B PLUG, pipe, 3 / 4 in. NPT, HDPE, regulator GASKET, seat 1 A, B PLUG, pipe, square, 3 / 8 in. NPT, Delrin BONNET, universal, low-pressure 1 7A O-RING, Viton, black, 2 1 / 2 x 2 5 / 8 x 1 / 16 in. 1 A STEM, body, regulator DIAPHRAGM, regulator, non-conductive 1 A NUT, stem, regulator BASE, regulator, non-conductive SPACER, plug ELBOW, male, 1 / 4 in. tube x 1 / 8 in. NPT, nylon SPRING, compression, x in. OD x 1 A 0.57 in TUBE, spacer, regulator CAPSCREW, sockethead, 1 / 4 20, in., 1 A nylon WASHER, flat, English, x 0.50 x in., brass NS TOOL, stem body, regulator 1 NOTE A: Part is included in the Rebuild Kit, part , listed on page 17. B: Part is included in the Stem and Seat Kit, part , listed on page 16. NS: Not Shown 2018 Nordson Corporation

20 16 Universal Automatic Non-Conductive Fluid Regulator A Figure 7 Universal Automatic Non-Conductive Regulator Adhesives and Lubricants Use these adhesives and lubricants when servicing your unit. Refer to Repair for application instructions. Part Description Quantity TAPE, PTFE, roll, 0.50 in. wide x 520 in. long ADHESIVE, threadlocking (Loctite Removable 242) LUBRICANT, O-ring, Parker (Parker O-Lube), 2 oz 1 Stem and Seat Kit See Figure 7. Item Part Description Quantity Note KIT, stem and seat, regulator STEM and seat assembly GASKET, seat Nordson Corporation

21 Universal Automatic Non-Conductive Fluid Regulator 17 Rebuild Kit See Figure 7. Item Part Description Quantity Note KIT, fluid regulator, low-pressure, rebuild O-RING, PTFE, in. ID x x 0.06 in. 1 wide STEM and seat assembly GASKET, seat 1 7A O-RING, Viton, black, 2 1 / 2 x 2 5 / 8 x 1 / 16 in DIAPHRAGM, regulator, non-conductive SPRING, compression, x in. OD x in CAPSCREW, sockethead, 1 / 4 20, in., nylon 1 Mounting Kits Kinetix Spray Gun Mounting Kit Part Description Quantity KIT, mounting, Kinetix, regulator COLLAR, in. ID x 1.25 in. OD SET SCREW, socket, 5 / 16 18, 2.00 in., cup point, zinc NUT, hex, jam, 5 / 16 18, steel, zinc 2 One-Inch Universal Gun Bar Mounting Kit Part Description Quantity KIT, 1 in., mounting universal, regulator COLLAR, split, 1 in. ID, aluminum (see Note A) NUT, hex, jam, 5 / 16 18, steel, zinc SET SCREW, socket, 5 / 16 18, 2.00 in., cup point, zinc 1 NOTE A: Collar includes two 1 / 4 28 x 5 / 8 in. socket head cap screws Nordson Corporation

22 18 Universal Automatic Non-Conductive Fluid Regulator Two-Inch Universal Gun Bar Mounting Kit Part Description Quantity KIT, 2 in., mounting universal, regulator BRACKET, color changer, threaded, 2 in. bar BRACKET, color changer, 2 in. bar SCREW, socket, 1 / 4 20 x 2.00 in WASHER, flat, regular, 1 / 4 in., zinc LOCK WASHER, English, split, 1 / 4 in., steel, nickel NUT, hex, jam, 5 / 16 18, steel, zinc SET SCREW, socket, 5 / 16 18, 2.0 in., cup point, zinc 1 Recommended Spare Parts Part Description Note VALVE, check, backflow, assembly A CONNECTOR, male, 3 / 8 in. tube x 3 / 8 in. NPT, nylon with plastic gripper B ELBOW, 90, male, 3 / 8 in. tube x 3 / 8 in. NPT, nylon with plastic gripper B CONNECTOR, male, 1 / 4 in. tube x 3 / 8 in. NPT, nylon with plastic gripper B ELBOW, 90, male, 1 / 4 in. tube x 3 / 8 in. NPT, nylon with plastic gripper B CONNECTOR, male, 1 / 2 in. tube x 3 / 8 in. NPT, nylon B NOTE A: This anti-backflow valve should be used on the pilot air line. B: You may use any combination of elbows and/or connectors in the regulator. Order two elbows and/or connectors for a non-circulating system. Order three elbows and/or connectors for a circulating system. Specifications Fluid inlet pressure: Regulated fluid pressure range: Maximum flow capacity: Wetted parts: Dimensions (with connectors): Air port: Fluid ports: Maximum 17.2 bar (250 psi) bar (5 100 psi) 5.3 l/min (1.4 gal/min) at 6.9 bar (100 psi) inlet pressure, and 3.4 bar (50 psi) regulated pressure Tungsten carbide, Delrin, Mylar, stainless steel, PTFE Height: 76.2 mm (3.0 in.) Diameter: 93.7 mm (3.690 in.) Weight: approximately 0.55 kg (1.2 lb) 1 / 8 in. NPT 3 / 8 in. NPTF 2018 Nordson Corporation

Rhino SD3/XD3 Air Motor

Rhino SD3/XD3 Air Motor Rhino SD3/XD3 Air Motor Customer Product Manual Issued 6/18 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson

More information

Rhino SD3/XD3 5-Gallon Follower Modules

Rhino SD3/XD3 5-Gallon Follower Modules Rhino SD3/XD3 5-Gallon Follower Modules Customer Product Manual Part 6033 03 Issued 6/8 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-939 or

More information

Mastic Gun. Customer Product Manual Part A. Issued 2/04 NORDSON CORPORATION AMHERST, OHIO USA

Mastic Gun. Customer Product Manual Part A. Issued 2/04 NORDSON CORPORATION AMHERST, OHIO USA Mastic Gun Customer Product Manual Issued 2/04 NORDSON CORPORTION MHERST, OHIO US Table of Contents Safety...................................... 1 Qualified Personnel........................ 1 Intended

More information

Ink-Dot Hydraulic System with Reservoir Manifold

Ink-Dot Hydraulic System with Reservoir Manifold Ink-Dot Hydraulic System with Reservoir Manifold Customer Product Manual Issued 7/10 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 This

More information

2 8 CC Ejector Gun. Customer Product Manual Part

2 8 CC Ejector Gun. Customer Product Manual Part 2 8 CC Ejector Gun Customer Product Manual Issued 03/14 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative.

More information

EcoLiner Compound Gun

EcoLiner Compound Gun EcoLiner Compound Gun Customer Product Manual Issued 3/06 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative.

More information

Rhino SD2/XD2 Frames

Rhino SD2/XD2 Frames Rhino SD2/XD2 Frames Customer Product Manual 0308-0 Issued 03/8 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 33-939 or contact your local Nordson

More information

High-Pressure Fluid Filters

High-Pressure Fluid Filters High-Pressure Fluid Filters Customer Product Manual Part 107971C02 NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its products.

More information

Pro-Meter Gear Metering Pump

Pro-Meter Gear Metering Pump Pro-Meter Gear Metering Pump Customer Product Manual Part 0808E-0 Issued 4/6 NORDSON CORPORATION AMHERST, OHIO USA tents Table of Contents Safety... Qualified Personnel... Intended Use... Regulations and

More information

A7A Single and Dual Automatic Airless Spray Guns

A7A Single and Dual Automatic Airless Spray Guns A7A Single and Dual Automatic Airless Spray Guns Customer Product Manual Issued 8/06 For parts and technical support, call the Finishing Customer Support Center at (800) 433-939. This document is available

More information

Low-Pressure Color Change Manifold

Low-Pressure Color Change Manifold Low-Pressure Color Change Manifold Customer Product Manual Issued 0/03 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 33-939 or contact your local

More information

Trilogy Air Spray and LVLP Automatic Spray Guns

Trilogy Air Spray and LVLP Automatic Spray Guns Trilogy Air Spray and LVLP Automatic Spray Guns Customer Product Manual Part 1601058-03 Issued 3/14 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800)

More information

Prodigy HDLV Pump. Customer Product Manual Part A02

Prodigy HDLV Pump. Customer Product Manual Part A02 Prodigy HDLV Pump Customer Product Manual Issued 1/07 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative.

More information

A16A Inside Stripe Gun

A16A Inside Stripe Gun A6A Inside Stripe Gun Customer Product Manual Issued 5/0 For parts and technical support, call the Finishing Customer Support Center at (800) 433-939. This document is subject to change without notice.

More information

Trilogy Air-Assisted Airless Manual Spray Gun

Trilogy Air-Assisted Airless Manual Spray Gun Trilogy Air-Assisted Airless Manual Spray Gun Customer Product Manual Issued 12/15 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact

More information

Circulating and Non-Circulating Color Change Manifolds

Circulating and Non-Circulating Color Change Manifolds Circulating and Non-Circulating Color Change Manifolds Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about

More information

Prodigy HDLV Generation II Pump Panel

Prodigy HDLV Generation II Pump Panel Prodigy HDLV Generation II Pump Panel Customer Product Manual Issued 01/10 For parts and technical support, call the Finishing Customer Support Center at (800) 433-9319. This document is subject to change

More information

Rhino SD2/XD2 Hydraulic Section

Rhino SD2/XD2 Hydraulic Section Rhino SD2/XD2 Hydraulic Section Customer Product Manual Issued 4/8 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-939 or contact your local Nordson

More information

Trilogy GP Air Spray and LVLP Gravity Fed Manual Spray Guns

Trilogy GP Air Spray and LVLP Gravity Fed Manual Spray Guns Trilogy GP Air Spray and LVLP Gravity Fed Manual Spray Guns Customer Product Manual Issued 7/13 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319

More information

CleanSpray XT Spray Guns

CleanSpray XT Spray Guns CleanSpray XT Spray Guns Customer Product Manual Issued 05/12 For parts and technical support, call the Finishing Customer Support Center at (800) 433-9319. This document is subject to change without notice.

More information

Prodigy HDLV Pump Manifold and Circuit Board

Prodigy HDLV Pump Manifold and Circuit Board Prodigy HDLV Pump Manifold and Circuit Board Customer Product Manual Issued 05/08 For parts and technical support, call the Finishing Customer Support Center at (800) 433-939. This document is available

More information

Auto-Flo II Dispense Valves for Pro-Meter-S and -S2K Applications

Auto-Flo II Dispense Valves for Pro-Meter-S and -S2K Applications Auto-Flo II Dispense Valves for Pro-Meter- and -2K Applications Customer Product Manual Issued / For parts and technical support, call the Finishing Customer upport Center at (800) 4-99. This document

More information

RediCoat by Nordson. Hopper and VBF Dolly Systems. Customer Product Manual Part A Issued 10/07

RediCoat by Nordson. Hopper and VBF Dolly Systems. Customer Product Manual Part A Issued 10/07 RediCoat by Nordson Hopper and VBF Dolly Systems Customer Product Manual Part 1082648A Issued 10/07 This document is subject to change without notice. Nordson Corporation Amherst, Ohio USA 2 Table of Contents

More information

Flow-Through-Felt Controller for Gravity Feed Applicators

Flow-Through-Felt Controller for Gravity Feed Applicators Flow-Through-Felt Controller for Gravity Feed Applicators Only Applicable to Contract E-001353269 Issued 1/13 For parts and technical support, call the Finishing Customer Support Center at (800) 433-9319.

More information

MEG Inside Stripe Applicator

MEG Inside Stripe Applicator MEG Inside Stripe Applicator Customer Product Manual Issued 0/8 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) -99 or contact your local Nordson representative.

More information

StediFlo 3:1 and 6:1 Low Pressure Pumps

StediFlo 3:1 and 6:1 Low Pressure Pumps StediFlo 3:1 and 6:1 Low Pressure Pumps Customer Product Manual Issued 7/12 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 This document

More information

Auto-Flo II Anti-Drool Dispense Valves

Auto-Flo II Anti-Drool Dispense Valves Auto-Flo II Anti-Drool Dispense Valves Customer Product Manual Issued 0/9 For parts and technical support, call the Finishing Customer Support Center at (800) 33-939. This document is subject to change

More information

SureMix Dispensing System

SureMix Dispensing System SureMix Dispensing System Customer Product Manual 1061906A Issued October 2005 NORDSON CORPORATION AMHERST, OHIO USA Safety...................................... 1 Qualified Personnel.......................

More information

RA-20 Rotary Atomizer

RA-20 Rotary Atomizer RA-20 Rotary Atomizer Customer Product Manual Issued 3/18 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative.

More information

7- and 10-Inch Air Motors with Air Valve

7- and 10-Inch Air Motors with Air Valve 7- and 10-Inch Air Motors with Air Valve Customer Product Manual Part NORDON CORPORATION AMHERT, OHIO UA Table of Contents afety... 1 Qualified Personnel... 1 Intended Use... 1 Regulations and Approvals...

More information

0 8 CC Accu-Drop Ejector Dispense Gun

0 8 CC Accu-Drop Ejector Dispense Gun 0 8 CC Accu-Drop Ejector Dispense Gun Customer Product Manual Issued 03/17 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your

More information

Pro-Swirl Applicator and Controller

Pro-Swirl Applicator and Controller Pro-wirl Applicator and Controller Manual 1009910C--02 Issued 2/10 NORDON CORPORATION AMHERT, OHIO UA afety... 1 Qualified Personnel... 1 Intended Use... 1 Regulations and Approvals... 1 Personal afety...

More information

Flow-Through-Felt Gravity Feed Applicator Tool

Flow-Through-Felt Gravity Feed Applicator Tool Flow-Through-Felt Gravity Feed Applicator Tool Customer Product Manual Part 0800 0 Issued 0/ For parts and technical support, call the Finishing Customer upport Center at (800) -99. This document is subject

More information

EP2 Pump System. Customer Product Manual Part A02

EP2 Pump System. Customer Product Manual Part A02 EP2 Pump System Customer Product Manual Issued 5/08 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative.

More information

Kinetix Electrostatic Spray Gun Automatic Airless

Kinetix Electrostatic Spray Gun Automatic Airless Kinetix Electrostatic Spray Gun Automatic Airless Customer Product Manual Issued 8/08 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact

More information

Encore HD Powder Spray System with Prodigy Pump Cabinet

Encore HD Powder Spray System with Prodigy Pump Cabinet Encore HD Powder Spray System with Prodigy Pump Cabinet Customer Product Manual Part 604979-06 Issued 05/8 For parts and technical support, call the Industrial Coating Systems Customer Support Center at

More information

Kinetix Electrostatic Spray Gun Automatic Version 60 kv Air Spray and KVLP Waterborne

Kinetix Electrostatic Spray Gun Automatic Version 60 kv Air Spray and KVLP Waterborne Kinetix Electrostatic Spray Gun Automatic Version 60 kv Air Spray and KVLP Waterborne Customer Product Manual Issued 8/08 For parts and technical support, call the Industrial Coating Systems Customer Support

More information

Trilogy Waterborne Electrostatic HVLP and Air Spray Automatic Gun

Trilogy Waterborne Electrostatic HVLP and Air Spray Automatic Gun Trilogy Waterborne Electrostatic HVLP and Air Spray Automatic Gun Customer Product Manual Issued 4/09 For parts and technical support, call the Finishing Customer Support Center at (800) 433-9319. This

More information

A7A Lancing Spray Guns

A7A Lancing Spray Guns A7A Lancing pray Guns Customer Product Manual Issued 8/18 For parts and technical support, call the Industrial Coating ystems Customer upport Center at (800) 33-9319 or contact your local Nordson representative.

More information

Econo-Coat Manual Powder Spray Gun

Econo-Coat Manual Powder Spray Gun Econo-Coat Manual Powder Spray Gun Customer Product Manual Issued 0/03 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-939 or contact your local

More information

Encore HD Automatic System Standalone Pump Stand

Encore HD Automatic System Standalone Pump Stand Encore HD Automatic System Standalone Pump Stand Customer Product Manual Part 6 0 Issued /7 For parts and technical support, call the Finishing Customer Support Center at (00) 4-99. This document is subject

More information

Auto-Flo Air-Assist Automatic Dispensing Valve

Auto-Flo Air-Assist Automatic Dispensing Valve Auto-Flo Air-Assist Automatic Dispensing Valve Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its

More information

CS-2T Timer. Customer Product Manual Part A

CS-2T Timer. Customer Product Manual Part A CS-2T Timer Customer Product Manual Issued 9/03 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative.

More information

Auto-Flo Panel Reinforcement Automatic Dispensing Valve

Auto-Flo Panel Reinforcement Automatic Dispensing Valve Auto-Flo Panel Reinforcement Automatic Dispensing Valve Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries

More information

. OBSOLETE, THIS DOCUMENT IS NO LONGER MAINTAINED. 2K Meter with Servo Drive

. OBSOLETE, THIS DOCUMENT IS NO LONGER MAINTAINED. 2K Meter with Servo Drive ., THIS DOCUMENT IS NO LONGER MAINTAINED. K Meter with Servo Drive Customer Product Manual 3365C NORDSON CORPORATION AMHERST, OHIO USA Safety....................................... 1 Repair (continued)

More information

Tribomatic II Extended Automatic Powder Spray Gun

Tribomatic II Extended Automatic Powder Spray Gun Tribomatic II Extended Automatic Powder Spray Gun Customer Product Manual Issued 7/06 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-939 or contact

More information

Tribomatic II Purgeable Automatic Powder Spray Gun

Tribomatic II Purgeable Automatic Powder Spray Gun Tribomatic II Purgeable Automatic Powder Spray Gun Customer Product Manual Issued 4/0 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 4-99 or contact

More information

Sure-Max Powder Transfer System

Sure-Max Powder Transfer System Sure-Max Powder Transfer System Customer Product Manual Issued 7/06 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local

More information

Inverted High Pressure Fluid Filters

Inverted High Pressure Fluid Filters Instruction Sheet P/N 33290-03 Description See Figure. Nordson high-pressure fluid filters prevent nozzle-plugging by filtering contaminants out of coating materials. These stainless steel, wall-mounted

More information

EP-2 Three-Piston Pump

EP-2 Three-Piston Pump EP- Three-Piston Pump Customer Product Manual Issued 0/ For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) -99 or contact your local Nordson representative.

More information

Sure Coat Modular Gun Control System Part D: Gun Purge Module. Customer Product Manual Part B

Sure Coat Modular Gun Control System Part D: Gun Purge Module. Customer Product Manual Part B Sure Coat Modular Gun Control System Part D: Gun Purge Module Customer Product Manual Issued 4/0 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 4-919

More information

Vantage Manual Powder Spray Gun

Vantage Manual Powder Spray Gun Vantage Manual Powder Spray Gun Customer Product Manual Issued 04/16 For parts and technical support, call the Finishing Customer Support Center at (800) 433-9319. This document is subject to change without

More information

Airless Spray Gun INSTRUCTIONS DP psi (345 bar) Maximum Working Pressure

Airless Spray Gun INSTRUCTIONS DP psi (345 bar) Maximum Working Pressure INSTRUCTIONS DP-6376 Airless Spray Gun 5000 psi (345 bar) Maximum Working Pressure INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Table of Contents Warnings......................................

More information

Big Bag Unloader. Customer Product manual Part Number Issued 07/17

Big Bag Unloader. Customer Product manual Part Number Issued 07/17 Big Bag Unloader Customer Product manual Part Number 7580188-01 Issued 07/17 For parts ordering, call the Industrial Coating Systems EU Customer Support Center on 0080070017001 or contact your local Nordson

More information

Nylon Fluid Regulators

Nylon Fluid Regulators Instruction Sheet P/N 08880B Introduction The FR- and RA- nylon fluid regulators are patented, electrically non-conductive, air-operated, pressure regulators. Except for the body shape and fluid connection

More information

HIVISC CE20 Gun. Customer Product Manual Part A NORDSON CORPORATION D AMHERST, OHIO D USA

HIVISC CE20 Gun. Customer Product Manual Part A NORDSON CORPORATION D AMHERST, OHIO D USA HIVIC CE20 Gun Customer Product Manual Part NORDON CORPORATION D AMHERT, OHIO D UA Nordson Corporation welcomes requests for information, comments and inquiries about its products. General information

More information

Paint/Solvent/Dump Valve and Flow-Through Valve

Paint/Solvent/Dump Valve and Flow-Through Valve Instruction Sheet P/N 08573D Paint/Solvent/Dump Valve and Flow-Through Valve. Description See Figure. The paint/solvent/dump valve is a normally-closed valve that opens to trigger and/or dump coating material.

More information

EP-2 Si Three-Piston Pump

EP-2 Si Three-Piston Pump EP- Si Three-Piston Pump Customer Product Manual Issued 0/ For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) -99 or contact your local Nordson representative.

More information

DISPLACEMENT PUMP INSTRUCTIONS-PARTS LIST Rev. K. Model , Series A Model , Series B Model , Series A

DISPLACEMENT PUMP INSTRUCTIONS-PARTS LIST Rev. K. Model , Series A Model , Series B Model , Series A INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. DISPLACEMENT PUMP 308190 Rev. K 3000 psi (210 bar) MAXIMUM WORKING PRESSURE Model

More information

0 900 psi Pressure-Reducing Diaphragm Regulator

0 900 psi Pressure-Reducing Diaphragm Regulator Instruction Sheet P/N 009506-09 0 900 psi Pressure-Reducing Diaphragm Regulator Description The Nordson 0 900 psi diaphragm regulator reduces high primary pressures to lower secondary pressures. It is

More information

Pro-Meter S-Series Dispensers

Pro-Meter S-Series Dispensers Pro-Meter S-Series Dispensers Customer Product Manual Part 076 0 Issued 0/8 For parts and technical support, call the Nordson Industrial Coating Systems Customer Support Center at (800) 99, or contact

More information

NVR-Series Vertical Reciprocators

NVR-Series Vertical Reciprocators NVR-Series Vertical Reciprocators Customer Product Manual Issued /6 For parts and technical support, call the Finishing Customer Support Center at (800) 4-99. This document is subject to change without

More information

Versa-Spray IPS Manual Electrostatic Porcelain Enamel Powder Spray Gun

Versa-Spray IPS Manual Electrostatic Porcelain Enamel Powder Spray Gun Versa-Spray IPS Manual Electrostatic Porcelain Enamel Powder Spray Gun Customer Product Manual Issued 11/06 For parts and technical support, call the Industrial Coating Systems Customer Support Center

More information

Standard and Conical AN Series Air Spray Nozzles

Standard and Conical AN Series Air Spray Nozzles Instruction Sheet P/N 107967E Standard and Conical AN Series Air Spray Nozzles Introduction The Nordson air spray nozzles described in this instruction sheet are categorized by their type of spray pattern:

More information

Inverted Dual High-Pressure Fluid Filter Assemblies

Inverted Dual High-Pressure Fluid Filter Assemblies Instruction Sheet P/N 1093-04 Inverted Dual High Pressure Fluid Filter Assemblies Introduction WARNG: High pressure fluids are hazardous. To prevent serious injury when installing and servicing filters,

More information

Sure Coat Modular Gun Control System Part B: Pneumatic Modules. Customer Product Manual Part B

Sure Coat Modular Gun Control System Part B: Pneumatic Modules. Customer Product Manual Part B Sure Coat Modular Gun Control System Part B: Pneumatic Modules Customer Product Manual Issued 4/03 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800)

More information

SP30 10:1 Piston Pump

SP30 10:1 Piston Pump Instruction Sheet P/N SP30 10:1 Piston Pump 1. Safety Read this section before using the equipment. This section contains recommendations and practices applicable to the safe installation, operation, and

More information

Prodigy Automatic Powder Spray Guns

Prodigy Automatic Powder Spray Guns Prodigy Automatic Powder Spray Guns Customer Product Manual Part 1054075-09 Issued 8/18 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or

More information

Page 1 of 19. Part# /10/2006

Page 1 of 19. Part# /10/2006 Part# 1002733-01 10/10/2006 This manual contains important information concerning the installation and operation of the gun washers listed above. Read manual thoroughly and keep for future reference INSTRUCTIONS

More information

SERVICE KITS REBUILD KIT DESCRIPTION CHART MODEL DESCRIPTION CHART SPECIFICATIONS X X 1 - B X - X X X - B

SERVICE KITS REBUILD KIT DESCRIPTION CHART MODEL DESCRIPTION CHART SPECIFICATIONS X X 1 - B X - X X X - B OPERATOR S MANUAL INCLUDING: SERVICE KITS, TROUBLESHOOTING, PARTS LIST, DISASSEMBLY & REASSEMBLY. HIGH PRESSURE MATERIAL REGULATOR 65178X-XXX-B RELEASED: 2-12-93 REVISED: 1-11-08 (REV. F) READ THIS MANUAL

More information

902 Powder Coating Booth

902 Powder Coating Booth 902 Powder Coating Booth Customer Product Manual Part For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative.

More information

Page 1 of 12. Part# /30/2016

Page 1 of 12. Part# /30/2016 Part# 1007480-02 9/30/2016 This manual contains important information concerning the installation and operation of the gun washers listed above. Read manual thoroughly and keep for future reference. INSTRUCTIONS

More information

Two-Component Meter. Customer Product Manual Part A NORDSON CORPORATION D AMHERST, OHIO D USA

Two-Component Meter. Customer Product Manual Part A NORDSON CORPORATION D AMHERST, OHIO D USA Two-Component Meter Customer Product Manual Part NORDSON CORPORATION D AMHERST, OHIO D USA Nordson Corporation welcomes requests for information, comments and inquiries about its products. Address all

More information

Prodigy Generation II High-Capacity HDLV Powder Transfer Pump

Prodigy Generation II High-Capacity HDLV Powder Transfer Pump Prodigy Generation II High-Capacity HDLV Powder Transfer Pump Customer Product Manual Issued 0/0 For parts and technical support, call the Finishing Customer Support Center at (800) 433-939. This document

More information

Hard Seat Fluid Pressure Regulator

Hard Seat Fluid Pressure Regulator Instruction Sheet P/N 04742-02 Description The Nordson hard seat fluid pressure regulator is designed for use with abrasive coatings. The regulator body is constructed of stainless steel with a nickel-plated

More information

0-800 psi Carbide Seat Fluid Pressure Regulator

0-800 psi Carbide Seat Fluid Pressure Regulator Instruction Sheet P/N 0350C 0-800 psi Carbide Seat Fluid Pressure Regulator Description The Nordson 0-800 psi carbide seat fluid pressure regulator is designed for use with general liquid coatings. The

More information

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup.

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup. Instructions/Parts MGFHVLP Mini Gravity Feed System FOR PRODUCT INFORMATION CALL: 1-800-742-7731 309989E For gravity feed spraying of automotive colors and clears. Ideal for touch-up and detail work. Important

More information

RA-20 Paint/Solvent/Dump Valve

RA-20 Paint/Solvent/Dump Valve Instruction Sheet P/N 74B0 RA-0 Paint/Solvent/Dump Valve Description The paint/solvent valve is a normally closed valve used to trigger coating material. The valve may be used alone to actuate paint or

More information

T1-Titanium Non-HVLP Spray Gun

T1-Titanium Non-HVLP Spray Gun T1-Titanium Non-HVLP Spray Gun THE SPRAY GUN PEOPLE FOR PRODUCT INFORMATION CALL: 1-800-742-7731 Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.

More information

0-500 PSI Soft Seat Fluid Pressure Regulator

0-500 PSI Soft Seat Fluid Pressure Regulator Instruction Sheet P/N 0953A Description The Nordson 0-500 psi soft seat fluid pressure regulator is designed for use with nonabrasive liquid coatings. The regulator body is constructed of stainless steel

More information

Instructions Parts List

Instructions Parts List Instructions Parts List CIRCULATING, HIGH PRESSURE Automatic Air Assisted Spray Gun 308780J 4000 psi (8 MPa, 80 bar) Maximum Working Fluid Pressure 100 psi (0.7 MPa, 7 bar) Maximum Working Air Pressure

More information

D Instructions/Parts. Siphon Feed Detail Spray Gun D

D Instructions/Parts. Siphon Feed Detail Spray Gun D Instructions/Parts D-5-55 Siphon Feed Detail Spray Gun FOR PRODUCT INFORMATION CALL: 1-800-742-7731 309991D Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.

More information

Versa-Spray IPS Automatic Electrostatic Porcelain Enamel Powder Spray Gun

Versa-Spray IPS Automatic Electrostatic Porcelain Enamel Powder Spray Gun Versa-Spray IPS Automatic Electrostatic Porcelain Enamel Powder Spray Gun Customer Product Manual Issued 05/6 For parts and technical support, call the Industrial Coating Systems Customer Support Center

More information

OPERATOR S MANUAL C INCLUDING: OPERATION, INSTALLATION & MAINTENANCE RELEASED:

OPERATOR S MANUAL C INCLUDING: OPERATION, INSTALLATION & MAINTENANCE RELEASED: OPERATOR S MANUAL 650719-C INCLUDING: OPERATION, INSTALLATION & MAINTENANCE RELEASED: 8-11-03 REVISED: 12-3-10 (REV. 08) 2" DIAPHRAGM PUMP U.L. LISTED, 1:1 RATIO, METALLIC READ THIS MANUAL CAREFULLY BEFORE

More information

Prodigy HDLV Pump Generation III, Pump Manifold and Circuit Board

Prodigy HDLV Pump Generation III, Pump Manifold and Circuit Board Prodigy HDLV Pump Generation III, Pump Manifold and Circuit Board Customer Product Manual Issued 3/6 For parts and technical support, call the Finishing Customer Support Center at (800) 433-939. Check

More information

Model C-1 Electrostatic Airless Spray Gun OBSOLETE. Customer Product Manual. Part D NORDSON CORPORATION AMHERST, OHIO USA

Model C-1 Electrostatic Airless Spray Gun OBSOLETE. Customer Product Manual. Part D NORDSON CORPORATION AMHERST, OHIO USA Model C-1 Electrostatic Airless Spray Gun Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its products.

More information

EPS-8 and EPS-9 Electrostatic Power Supplies

EPS-8 and EPS-9 Electrostatic Power Supplies EPS-8 and EPS-9 Electrostatic Power Supplies Customer Product Manual Part For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your

More information

Spray Pressure Control Manifold

Spray Pressure Control Manifold Instruction Sheet P/N 0870G0 WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Introduction The

More information

Operating Manual High Viscosity Dispense Valve Item #

Operating Manual High Viscosity Dispense Valve Item # Operating Manual High Viscosity Dispense Valve Item # 984594 CLOSE OPEN Item # 984594 Label # 8901197 Warnings INJECTION HAZARD Spray from the valve, hose leaks, or ruptured components can inject fluid

More information

TCU Flushing Manifold and RTD Installation

TCU Flushing Manifold and RTD Installation Instruction Sheet P/N 1614041-01 This instruction is for installing temperature control unit (TCU) flush manifold and RTD assembly onto the heat exchanger for both new systems and existing systems. Follow

More information

Soft Seat Fluid Pressure Regulator

Soft Seat Fluid Pressure Regulator Instruction Sheet P/N 04622F Description The Nordson soft seat fluid pressure regulator is designed for use with nonabrasive liquid coatings. The regulator body is constructed of stainless steel with a

More information

Spray Pressure Control Manifold

Spray Pressure Control Manifold Instruction Sheet P/N 0870-0 WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Introduction The

More information

Model 570 Automatic Mastic Airless Spray Gun

Model 570 Automatic Mastic Airless Spray Gun Model 570 Automatic Mastic Airless Spray Gun 6700-0000-7 For Professional Use Only warning high pressure warning Maximum working Pressure Up to 4000 pounds per square inch Do not point spray gun at any

More information

Prodigy Robot Gun. For parts and technical support, call the Finishing Customer Support Center at (800)

Prodigy Robot Gun. For parts and technical support, call the Finishing Customer Support Center at (800) Prodigy Robot Gun Customer Product Manual Issued 3/14 For parts and technical support, call the Finishing Customer Support Center at (800) 433-9319. This document is subject to change without notice. Check

More information

AIR MOTOR DRIVE

AIR MOTOR DRIVE SERVICE MANUAL EN 31-450 AIR MOTOR DRIVE 77-3140-R1.0 (9/2017) 1 / 8 In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: Hazards or unsafe

More information

Model 550 Automatic Airless Spray Gun

Model 550 Automatic Airless Spray Gun Model 550 Automatic Airless Spray Gun For Professional Use Only warning high pressure warning Maximum Working pressure Up to 3000 pounds per square inch Do not point spray gun at any part of the human

More information

High-Capacity Continuous Flow Iso-Flo Voltage-Block System

High-Capacity Continuous Flow Iso-Flo Voltage-Block System High-Capacity Continuous Flow Iso-Flo Voltage-Block System Part For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-939 or contact your local Nordson

More information

Husky 307 Air-Operated Diaphragm Pumps

Husky 307 Air-Operated Diaphragm Pumps INSTRUCTIONS PARTS LIST 308 194 This manual contains important warnings and information. READ AND RETAIN FOR REFERENCE Rev. E Supersedes C and PCN D Husky 307 Air-Operated Diaphragm Pumps 100 psi (7 bar)

More information

Manual Clear Primer Application System

Manual Clear Primer Application System Manual Clear Primer Application ystem Part 107002B NORDON CORPORATION D AMHERT, OHIO D UA Nordson Corporation welcomes requests for information, comments and inquiries about its products. Address all correspondence

More information

1-1/2" DIAPHRAGM PUMP 1:1 Ratio (metallic) with Cone Checks

1-1/2 DIAPHRAGM PUMP 1:1 Ratio (metallic) with Cone Checks OPERATOR S MANUAL 670053-X-X INCLUDING: OPERATION, INSTALLATION & MAINTENANCE RELEASED: 3-24-06 REVISED: 5-11-15 (REV. F) 1-1/2" DIAPHRAGM PUMP 1:1 Ratio (metallic) with Cone Checks READ THIS MANUAL CAREFULLY

More information