Splice Only Sub Assembly. Follow all local safety regulations related to optical fibre plant elements

Size: px
Start display at page:

Download "Splice Only Sub Assembly. Follow all local safety regulations related to optical fibre plant elements"

Transcription

1 FIST-SOSA I N S T A L L A T I O N I N S T R U C T I O N Splice Only Sub Assembly Single element sub-assemblies Single circuit sub-assemblies Ribbon sub-assemblies FIST-SOSA-2SE8/2- X FIST-SOSA-4SC2/0- X FIST-SOSA-2R4- X FIST-SOSA-2SE12/4- X FIST-SOSA-4SC4/2- X FIST-SOSA-4R4- X FIST-SOSA-4SE8/2- X FIST-SOSA-8SC2/0- X FIST-SOSA-4SE12/4- X FIST-SOSA-8SC4/2- X X = S (SMOUV 45 mm) or A (ANT) or Q (QPAK) Contents 1 Introduction 2 General 2.1 Abbreviations 2.2 Kit contents 2.3 Accessories 2.4 Items required from FIST installation kit 2.5 Tools 3 Installation 3.1 SOSA installation 3.2 Splicing fibers 3.3 SC and SE routing 3.4 FOPT-SF routing on FAS 3.5 Important steps during installation 1 Introduction A SOSA (Splice Only Sub-Assembly) is an assembly of a number of trays mounted on a base plate. A SOSA-SE or R4 assembly has 2 or 4 single element trays. A SOSA-SC assembly has 4 or 8 single circuit trays. The base plate allows the trays to hinge, giving access to all the fibers. Splicing in single elements trays is typically done on a cable element basis (max. 12 fibers). Splicing in the single circuit trays is typically on a two-fiber (transmit and receive) basis but can range from 1 up to 4 fibers. Splicing in the ribbon 4 trays is typically done on single ribbon basis but can range up to 2 ribbons. Note: the user must be aware that this product is specifically designed for the fiber optic network and should be handled with care to prevent damage which may be caused by dropping the product or its contents. Follow all local safety regulations related to optical fibre plant elements To clean FIST components, the use of isopropylalcohol is recommended.

2 2 General Specific network elements installation instructions can overrule the SOSA installation instruction. 2.1 Abbreviations 2.3 Accessories SECO 4, SECO 6, FOPT-SF, FOPT-CS, FOPT-CT In the following installation instruction both SECO 4 and SECO 6 are covered. SECOs are used to convert loose tube cable elements with primary coated fibers into single circuits (typically 2 fibers). A SECO 4 is used to convert a loose tube with 8 fibers into 4 single circuits. A SECO 6 is used to convert a loose tube with 12 fibers into 6 single circuits. A SECO is clicked onto the FAS plate. SECO s and transportation tubes are pre-installed in some FIST products. Fiber Arrangement System FAS Loose tube breakout system SECO Termination Unit Fiber optic protection tubes: Cable to SECO FOPT-CS SECO to FAS FOPT-SF Cable to tube FOPT-CT 2.2 Kit content Three sizes of transportation tubes are used for guiding the fibers to the SECO and from it to the splicing trays. A FOPT-SF Δ 1.2 x 1.8 is used to exit the SECO towards the splicing trays. B FOPT-CS Δ 2.4 x 3.1 is used to enter the SECO. C FOPT-CT Δ 3.15 X 4.3 is used to make the transition from the loose tube to the FOPT-CS. If the FOPT-CS fits over the loose tube, the FOPT-CT is not needed. Loose buffer tube CT CS SF Remark: for cleaning FIST components, use of isopropylalcohol cleaning tissue is recommended. 2.4 Items required from FIST installation kit 5 sub-assemblies (being XSE or XSC or XR4) Fiber guiding pin Installation instruction FOPT-CS FOPT-CT FOPT-SF SECO if not pre-installed Marker Tray lid 2.5 Tools FACC-tube-cutter 01 : to cut transportation tubes FACC-tube-stripper 02 : to strip loose tubes Note: Ribbon installation may require specific accessories and tools and is covered in specific installation instructions. 2

3 3 Installation 3.1 SOSA installation Make sure the grooves are clean on the FAS module area before fitting modules Identify the tray to be worked on and make it accessible. If the FAS module/trays are in vertical position you will have to support the trays above the selected one using the tray wedge. The wedge is located in the spare hinge holes between trays, and attaches to the back of the upper tray (snap fit) To fit a module: open the module in the middle, hold the module base, push and slide it onto the FAS module area as close as possible to the FAS entrance area positioned in the correct way; i.e. the back of the trays should face the FAS entrance area. Do not leave any space between the different modules. Make sure that the module is positioned properly before clicking it onto the FAS and check the snap fit before continuing! Make sure that the SOSA is clicked in well. Identify the module and number the trays The SOSA module base is numbered To remove a module: carefully lift the base at the centre of its length with the lip and push the base at the other side SECO s are mounted according to the installation instruction of the network element concerned. The first step is to define how many FOPT-SF will be needed for each SECO. Trays will be fed by FOPT-SF tubes, containing 1 up to 12 primary coated fibers or 1 secondary coated fiber For SC trays, tray 1 has to be fed from groove 1, tray 2 from groove 2, etc. Note : When entering with two FOPT-SF in one groove, the top one should be prepared as described above (90 mm under the SOSA). The bottom one will only be inserted 20 mm under the SOSA. 3

4 3.1.9 Cut the FOPT-CS to the appropriate length, using the FACC- tube-cutter 01, strip the loose tube and clean the fibers. The fibers need to be cleaned thoroughly so that they will not stick during feeding. Separate the fibers and guide them into the FOPT-CS. Insert the FOPT-CT over the loose tube so there is a gap of at least 10 mm between the loose tube and the FOPT-CS 3.1.6a SE trays have double thickness, so use the odd number grooves, i.e. tray 1 to be fed from groove 1, tray 2 from groove 3 etc. But one can use the both grooves if necessary (i.e. 4 secondary coated fibers) Note: When entering with two FOPT-SF in one groove, the top one should be prepared as described above (90 mm under the SOSA). The bottom one will only be inserted 20 mm under the SOSA Mount the SECO on the FOPT-CS Each FOPT-SF tube that will leave a SECO should be cut to the correct length, depending on the tray to be fed. Guide the FOPT-SF to the appropriate tray and push the tube into the groove under the tray until it will go no further If necessary, divide the fibers into circuits and place each circuit in an outgoing port of the SECO (dark fibers should be placed on top ports). Do not click the SECO onto the FAS plate yet Insert and feed the fibers into the selected tube (FOPT-SF) until they appear at the opposite entrance to the tray. Take the fibers and pull the remaining length gently through the tube Cut each tube 10 mm from the SECO. 4

5 Place the FOPT-SF in the SECO By using termination units, maximum two secondary coated fibers should be passed through the termination unit in accordance with individual installation instructions. No SECO is required. When stripping secondary coated fibers, make the transition under the module base plate in the middle of the SOSA. Remark: If routing pigtails to a SE or SC tray with a non flexible coating, the coating will have to be stripped Click the SECO onto the FAS-plate. 3.2 Splicing fibers in SC and SE trays To avoid buckling of fibers in the transportation tubes pull gently on the fibers and store the fibers temporarily on a tray Take the stored fibers out of the tray (a fiber guiding pin can be used) Storing dark fibers can be done in three different ways. 1) Organise dark fibers into the different trays, following instructions as described. 2) Organise dark fibers into the first available SE tray from a SOSA module (with a max. of 24 primary coated fibers). 3) Store all dark fibers into the dark fiber storage area. If using the dark fiber storage area, cut the FOPT-SF for each circuit so that the FOPT-SF sits 20 mm inside the dark fiber storage area Splice and put the splice protector on the fibers. Initial fiber length on each tray is recommended to be 1.5 m on both sides, to allow 10 resplices. 1.2 m if 2 secondary coated fibers are used in SC tray. Note: use only 45 mm long SMOUV. 5

6 ANT in SE tray Take the splice protector and put the splice protector centred towards the splice holder Q-pack in SC tray Smouv in SC tray Q-pack in SE tray Smouv in SE tray ANT in SC tray Make several loops and place the fibers on the tray. Avoid tight wrapping around the centre of the tray. If the length of the fiber is less than 900 mm it may be difficult to store the fiber on the tray and re-splicing to a correctly cut length may be necessary. When using a mixture of primary and secondary fibers in SC tray, store the primary coated fiber first. 6

7 3.3 SE and SC routing Fill in the identification in the moulded table, in the centre of the tray SE-tray routing A tray lid has to be positioned on the last tray SC-tray routing To remove the traylid, pull the lid on the bottom Secure the trays with hook and loop fastener strap. 7

8 3.4 FOPT-SF routing on FAS Loop back. 3.5 Important steps during installation Make sure that the grooves on the FAS are clean (3.1). Cut the transportation tubes with the tube-cutter. When entering with two FOPT-SF in one groove, the top one should be prepared as described above (90 mm under the SOSA). The bottom one will only be inserted 20 mm under the SOSA (3.1.6 and 3.1.6a). Cut the FOPT-SF 10 mm from the SECO (so FOPT-SF will not be fully inserted under the modules) (3.1.8). Clean fibers (3.1.9). When using FOPT-CT, leave a 10 mm gap between the loose tube and FOPT-CS (3.1.9) Push the FOPT-SF + FOPT-CS completely in the SECO ( and ). Avoid buckling of the fibers (3.1.15). Initial fiber length is 1.5 m or 1.2 m in case of 2 secondary coated fibers in SC tray (3.2.2). Use only 45 mm long SMOUV (3.2.2). Tyco Electronics Raychem bvba Diestsesteenweg 692 B-3010 Kessel-Lo, Belgium Tel.: Fax: FIST, SMOUV, TE (logo) and TE Connectivity are trademarks of the TE Connectivity group of companies and its licensors. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity obligations shall only be as set forth in TE Connectivity Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. TC 458/N/IP/2 01/99

19 1HU Splicing and Front Patching Shelf

19 1HU Splicing and Front Patching Shelf FOMS-FPS-O-XXXX-XX I N S T A L L A T I O N I N S T R U C T I O N 19 1HU Splicing and Front Patching Shelf Contents 1 Introduction 2 General 2.1 Characteristics 2.2 Kit contents 2.3 Tools 3 Installation

More information

FIST-GSS2 FIST-GSS3. Fist Generic Splicing Shelf. Contents. 1 Introduction. 2 General. 3 Installation of the shelf. 5 Termination of the pigtails

FIST-GSS2 FIST-GSS3. Fist Generic Splicing Shelf. Contents. 1 Introduction. 2 General. 3 Installation of the shelf. 5 Termination of the pigtails FIST-GSS2 FIST-GSS3 I N S T A L L A T I O N I N S T R U C T I O N Fist Generic Splicing Shelf Contents 1 Introduction 2 General 2.1 Kit content 2.2 Tools 3 Installation of the shelf 3.1 Mounting the shelf

More information

FIST-GSS2. Fist Generic Splicing Shelf MK2. Contents. 1 Introduction. 2 General. 3 Installation of the shelf. 5 Termination of the pigtails

FIST-GSS2. Fist Generic Splicing Shelf MK2. Contents. 1 Introduction. 2 General. 3 Installation of the shelf. 5 Termination of the pigtails FIST-GSS2 I N S T A L L A T I O N I N S T R U C T I O N Fist Generic Splicing Shelf MK2 Contents 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Optional extra s 3 Installation of the shelf 3.1

More information

FIST-FPS. Front Patching Shelf. Contents. 1 Introduction. 3 Installation of the shelf. 2 General. 1 Introduction

FIST-FPS. Front Patching Shelf. Contents. 1 Introduction. 3 Installation of the shelf. 2 General. 1 Introduction FIST-FPS I N S T A L L A T I O N I N S T R U C T I O N Front Patching Shelf Contents 1 Introduction 2 General 2.1 Kit content 2.2 Tools 3 Installation of the shelf 3.1 Side cable termination directly on

More information

Patching & Splicing Shelf. 4.2 Side cable termination directly on the shelf using cable termination plate. IFC cable/break-out cable

Patching & Splicing Shelf. 4.2 Side cable termination directly on the shelf using cable termination plate. IFC cable/break-out cable FIST-GPS2/GPST-12 I N S T A L L A T I O N I N S T R U C T I O N Patching & Splicing Shelf Contents 1 Introduction 2 General 2.1 Kit contents 2.2 Tools 2.3 Optional accessories 3 Installation of the shelf

More information

FIST-GMS2. FIST Generic Mixed Shelf MK2. Contents. 1 Introduction. 5 Termination of the pigtails. 2 General. 6 Splicing + fiber storage

FIST-GMS2. FIST Generic Mixed Shelf MK2. Contents. 1 Introduction. 5 Termination of the pigtails. 2 General. 6 Splicing + fiber storage FIST-GMS2 I N S T A L L A T I O N I N S T R U C T I O N FIST Generic Mixed Shelf MK2 Contents 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Optional extra s 3 Installation of the shelf 3.1 Mounting

More information

FIST-GPS2-J. 19 2HU Splicing, Patching and Storage shelf. 5 Fiber routing. 1 Introduction. Contents. 2 General. 6 Storage. 3 Installation of the shelf

FIST-GPS2-J. 19 2HU Splicing, Patching and Storage shelf. 5 Fiber routing. 1 Introduction. Contents. 2 General. 6 Storage. 3 Installation of the shelf FIST-GPS2-J I N S T A L L A T I O N I N S T R U C T I O N 19 2HU Splicing, Patching and Storage shelf Contents 1 Introduction 2 General 2.1 Kit contents 2.2 Tools 2.3 Optional extras 3 Installation of

More information

FOSC-400D5 INSTALLATION INSTRUCTION. Fibre Optic Splice Closure with integrated organiser system

FOSC-400D5 INSTALLATION INSTRUCTION. Fibre Optic Splice Closure with integrated organiser system FOSC-400D5 INSTALLATION INSTRUCTION Fibre Optic Splice Closure with integrated organiser system 1 General 1.1 The installation instruction describes the necessary steps to install the FOSC-400D5. The

More information

BUDI-S-SP. Building distributor. Introduction. Seals. Kit content. Accessories. TC-957-IP Rev A, Feb Wrap around cable seals

BUDI-S-SP. Building distributor. Introduction. Seals. Kit content. Accessories. TC-957-IP Rev A, Feb Wrap around cable seals BUDI-S-SP I N S T A L L A T I O N I N S T R U C T I O N TC-957-IP Rev A, Feb 2017 www.commscope.com Building distributor Introduction Seals The Budi is a building distributor for a fiber managment system

More information

Fiber optic splice closure

Fiber optic splice closure FOSC-450A I N S T A L L A T I O N I N S T R U C T I O N TC-772-IP Rev A, Mar 2017 www.commscope.com Fiber optic splice closure Content 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Accessories

More information

FOSC-400A4 INSTALLATION INSTRUCTION

FOSC-400A4 INSTALLATION INSTRUCTION FOSC-400A4 INSTALLATION INSTRUCTION TC-441-IP Rev A, Mar 2017 www.commscope.com Fibre Optic Splice Closure with integrated organiser system 1 General 1.1 The installation instruction describes the necessary

More information

8400 Series Fiber Distribution System

8400 Series Fiber Distribution System 8400 Series Fiber Distribution System Instructions January 1997 34-7041-4699-1-A 1 Contents: 1.0 General... 3 2.0 System Components... 4 3.0 System Engineering... 5 4.0 Hardware Installation... 7 5.0 Cable

More information

Accessories for FIST Racks and Shelves

Accessories for FIST Racks and Shelves Accessories for FIST Racks and Shelves Description The FIST-GSS2/3, FIST-GPS2/3 and FIST-GMS2 shelves feature FIST fiber management system technology. They mount ETSI (FIST-GR3), 9- or 5-inch racks. Accessories

More information

Fiber Splice Panel Rack Mount User Manual

Fiber Splice Panel Rack Mount User Manual Fiber Splice Panel Rack Mount User Manual Content Page INTRODUCTION... 1 Revision History... 1 List of Changes... 1 Trademark Information... 2 Admonishments... 2 1. DESCRIPTION... 2 A. Product Definition

More information

AquiTron. AT-PIR-SOV Water Shut-Off System INSTALLATION INSTRUCTIONS

AquiTron. AT-PIR-SOV Water Shut-Off System INSTALLATION INSTRUCTIONS AquiTron Water Shut-Off System INSTALLATION INSTRUCTIONS System Please read these instructions carefully and keep them in a safe place (preferably close to the module) for future reference. These instructions

More information

System description/overview/kit overview...5 Assembly procedures...7. Channels Solid channel with cover...10 Slotted channel with cover...

System description/overview/kit overview...5 Assembly procedures...7. Channels Solid channel with cover...10 Slotted channel with cover... Introduction System description/overview/kit overview...5 ssembly procedures...7 hannels Solid channel with cover...10 Slotted channel with cover...10 Fittings hannel splice...12 Fitting splice...12 Horizontal

More information

FOSC-100 B/H FOSC-100 B2/H

FOSC-100 B/H FOSC-100 B2/H FOSC-100 B/H FOSC-100 B2/H INSTALLATION INSTRUCTION TC-273-IP Rev A, Mar 2017 www.commscope.com Fiber Optic Splice Closure with integrated organizer system 1 1 General 1.1 The installation instruction

More information

C Power Connection Kit

C Power Connection Kit 1548-4000C Power Connection Kit For use with Dekoron 2700 Family of Heating Cables Installation Instructions Kit Description The Dekoron 1548-4000C electrical connection kit distirbuted by Heat-Line is

More information

CS Fiber Optic Splice Case. Instruction

CS Fiber Optic Splice Case. Instruction 3 2179-CS Fiber Optic Splice Case Instruction 2179-CS Fiber Optic Splice Case Description 1.0 General 1.1 The 3M 2179-CS Fiber Optic Splice Cases are closures that can be used in buried, underground, aerial,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 144F TABLE OF CONTENTS GENERAL... 2 SPECIFICATIONS... 2 PACKAGE CONTENTS... 2 PACKAGE CONTENTS: ACCESSORIES... 3 REQUIRED TOOLS... 3 ADD-ON COMPONENTS... 3 CABINET MOUNTING WALL MOUNT BRACKET ATTACHMENT...

More information

LPC Series Fiber Panel 12/24 Fiber Rack-Mount Enclosure Installation Instructions

LPC Series Fiber Panel 12/24 Fiber Rack-Mount Enclosure Installation Instructions LPC Series Fiber Panel 12/24 Fiber Rack-Mount Enclosure Installation Instructions ADCP-92-129 Issue 1 6/2010 Content Page INTRODUCTION.............................................................................

More information

3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900 µm Instructions

3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900 µm Instructions 3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900 µm Instructions February 2008 78-8140-1581-0 Contents 1.0 Summary...3 2.0 Connector Preparation...4 3.0 Fiber Preparation...4 4.0 Fiber

More information

3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900-µm. Instructions. October C

3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900-µm. Instructions. October C 3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900-µm Instructions October 2010 78-8140-1581-0-C Contents 1.0 Summary...3 2.0 Connector Preparation...4 3.0 Fiber Preparation...4 4.0 Fiber

More information

Termination Procedures for Triaxial Connectors D , D , and D

Termination Procedures for Triaxial Connectors D , D , and D Page: 1 of 7 Termination Procedures for Triaxial Connectors D-621-0001, D-621-0002, and D-621-0003 1. Scope This standard covers the procedures for terminating triaxial and twinaxial cables to the triaxial

More information

710 Splicing Rig. Instructions. January E

710 Splicing Rig. Instructions. January E 710 Splicing Rig Instructions January 2007 Table of Contents 1.0 General Statement...4 2.0 3M 710-UTK25A Splicing Rig and Field Maintenance Kit...4 3.0 Straight Splicing using the 3M 710 25-pair modules...6

More information

PREMIUM QUALITY MANUFACTURING OF CRIMP CONNECTIONS AMP 3K, 5K, GII AND GII + TERMINATORS

PREMIUM QUALITY MANUFACTURING OF CRIMP CONNECTIONS AMP 3K, 5K, GII AND GII + TERMINATORS PREMIUM QUALITY MANUFACTURING OF CRIMP CONNECTIONS AMP 3K, 5K, GII AND GII + TERMINATORS AMP-O-LECTRIC GII Terminator Safety first. Improved guarding on the Model G II terminator provides open access for

More information

Universal Splice Tray Installation Instructions

Universal Splice Tray Installation Instructions Universal Splice Tray Installation Instructions Table of Contents General Product Information... 1.0 Safety Precautions... 2.0 Package Contents... 3.0 Installing the Product... 4.0 Tower Mounting... 5.0

More information

12-Inch Hybrid Fiber Access Terminal Installation Instructions

12-Inch Hybrid Fiber Access Terminal Installation Instructions 12-Inch Hybrid Fiber Access Terminal Installation Instructions 19683-A Content Page 1 PRODUCT DESCRIPTION.................................................................. 2 2 PRODUCT FUNCTION.....................................................................

More information

3M Fiber Dome Closure FDC 10

3M Fiber Dome Closure FDC 10 3M Fiber ome losure F 10 With 3M Fiber Optic Splice Tray 2541 Instructions 1.0 General 2.0 Kit ontents The 3M Fiber ome losure F 10 can accommodate two 1.06" (27 mm) main cables, five 0.71" (18 mm) branch

More information

3M No Polish LC/APC Connector SM, Angle Splice, 250/900 µm 8830-APC/AS

3M No Polish LC/APC Connector SM, Angle Splice, 250/900 µm 8830-APC/AS 3M No Polish LC/APC Connector SM, Angle Splice, 250/900 µm 8830-APC/AS Instructions January 2009 78-8140-3691-5-A Contents 1.0 Summary...3 2.0 Connector Preparation...4 3.0 Fiber Preparation...4 4.0 Fiber

More information

PREMIUM QUALITY MANUFACTURING OF CRIMP CONNECTIONS AMP 3K, 5K, GII AND GII + TERMINATORS

PREMIUM QUALITY MANUFACTURING OF CRIMP CONNECTIONS AMP 3K, 5K, GII AND GII + TERMINATORS PREMIUM QUALITY MANUFACTURING OF CRIMP CONNECTIONS AMP 3K, 5K, GII AND GII + TERMINATORS AMP-O-LECTRIC GII Terminator Safety first. Improved guarding on the Model G II terminator provides open access for

More information

3M No Polish LC Connector SM and MM, Flat Splice, 250/900 µm

3M No Polish LC Connector SM and MM, Flat Splice, 250/900 µm 3M No Polish LC Connector SM and MM, Flat Splice, 250/900 µm Instructions January 2009 78-8140-3696-4-A 3 Contents 1.0 Kit Contents... 3 2.0 3M No Polish LC Connector SM & MM 250/900 µm... 4 Safety Precautions

More information

ELE-3COP-359 Title - Braid termination using a Tinel Lock TM ring installed using a resistance heater.

ELE-3COP-359 Title - Braid termination using a Tinel Lock TM ring installed using a resistance heater. Before starting work please read this document carefully and note the guidance given. 1 Purpose and Scope This COP describes the procedure to be used when carrying out the installation of a Tinel-Lock

More information

Fitting Instruction for EZI-GRIP Bike Rack

Fitting Instruction for EZI-GRIP Bike Rack Fitting Instruction for EZI-GRIP Bike Rack Congratulations on purchasing Ezi-Grip to carry your valued bicycles. We are sure you will get many years of enjoyable use from your Ezi-Grip Bike Rack. These

More information

ECONOMY POWER 2.5 CONNECTORS

ECONOMY POWER 2.5 CONNECTORS ECONOMY POWER 2.5 CONNECTORS The Economy Power 2.5 (EP 2.5) connector is a single row or dual row crimp connector system. Based on a 2.5mm (0.098 ) centerline pitch, it is a very compact solution. EP 2.5

More information

SUBMERSIBLE TRANSDUCER CABLE REPAIR

SUBMERSIBLE TRANSDUCER CABLE REPAIR SUBMERSIBLE TRANSDUCER CABLE REPAIR One of the most frequent causes of level transducer failure is its cable being cut, which allows moisture to infiltrate the transducer cable jacket. Many of our customers

More information

***Please follow instructions for ease of installation and correct fit.***

***Please follow instructions for ease of installation and correct fit.*** RAMPAGE P R O D U C T S Installation Instructions Part number 1094XX Frameless Soft Top for Jeep Wrangler YJ 1992-1995 with Half Doors NOTE: Installation of the top in warm weather is optimal for ease

More information

CORCOM /// EMI FILTERS FOR MEDICAL APPLICATION - PRODUCT OVERVIEW. CORCOM EMI Filters for Medical Application - Product Overview

CORCOM /// EMI FILTERS FOR MEDICAL APPLICATION - PRODUCT OVERVIEW. CORCOM EMI Filters for Medical Application - Product Overview CORCOM /// EMI FILTERS FOR MEDICAL APPLICATION - PRODUCT OVERVIEW CORCOM EMI Filters for Medical Application - Product Overview CORCOM /// EMI FILTERS FOR MEDICAL APPLICATION - PRODUCT OVERVIEW WHAT S

More information

COYOTE 28" GLC (Ground Level Closure) Complete Assembly Installation

COYOTE 28 GLC (Ground Level Closure) Complete Assembly Installation NOVEMBER 2016 COYOTE 28" GLC (Ground Level Closure) Complete Assembly Installation Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED

More information

Mini-OTE 400. Mini-OTE 400. Content 1 General 1.1 General product information 1.2 Cable types 1.3 Symbols in this guide.

Mini-OTE 400. Mini-OTE 400. Content 1 General 1.1 General product information 1.2 Cable types 1.3 Symbols in this guide. Mini-OTE 400 INSTALLATION INSTRUCTION TC-1335-IP Rev C, March 2017 www.commscope.com Mini-OTE 400 Content 1 General 1.1 General product information 1.2 Cable types 1.3 Symbols in this guide 2 Tools Required

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Thank you for purchasing a LOMAX TM Hard Tri-Fold or Professional Series Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship.

More information

INSTALLATION INSTRUCTIONS AND OWNER S MANUAL

INSTALLATION INSTRUCTIONS AND OWNER S MANUAL INSTALLATION INSTRUCTIONS AND OWNER S MANUAL Thank you for purchasing the AlloyCover from WeatherTech. Manufactured with pride using superior quality materials and workmanship. With proper care, your cover

More information

3M Cold Shrink Silicone Rubber Termination QT-III 7600-S-3G Series Three-Core Outdoor Termination

3M Cold Shrink Silicone Rubber Termination QT-III 7600-S-3G Series Three-Core Outdoor Termination 3M Cold Shrink Silicone Rubber Termination QT-III 7600-S-3G Series Three-Core Outdoor Termination Instructions IEEE Std. No. 48 Class 1 Termination CAUTION Working around energized electrical systems may

More information

F Ext Cab 40/20/40 w/ integral seatbelt Installation

F Ext Cab 40/20/40 w/ integral seatbelt Installation 2001-07 F-250-350 Ext Cab 40/20/40 w/ integral seatbelt Installation Step 1. Driver and Passenger Tops/DT & PT: Temporarily remove the headrests by lifting them up all the way. Then with slight upward

More information

COYOTE Dome Closure 9.5" x 28" with Transition Tray for High Density Splice Applications

COYOTE Dome Closure 9.5 x 28 with Transition Tray for High Density Splice Applications OCTOBER 2017 COYOTE Dome Closure 9.5" x 28" with Transition Tray for High Density Splice Applications Be sure to read and completely understand this procedure before applying product. Be sure to select

More information

Accessories for FIST racks and shelves

Accessories for FIST racks and shelves Accessories for FIST racks and shelves Ordering guide Description The FIST-GSS2/3, FIST-GPS2/3 and FIST-GMS2 shelves feature FIST fiber management system technology. They mount ETSI (FIST-GR3), 9- or 5-inch

More information

INSTALLATION INSTRUCTIONS AND OWNER S MANUAL

INSTALLATION INSTRUCTIONS AND OWNER S MANUAL INSTALLATION INSTRUCTIONS AND OWNER S MANUAL Thank you for purchasing the AlloyCover from WeatherTech. Manufactured with pride using superior quality materials and workmanship. With proper care, your cover

More information

EZ-R7 T-Plug. Universal 7-Pin Heavy Duty Plug For Vehicles equipped with 7-Way Trailer Connectors. Installation Instructions and Product Warranty

EZ-R7 T-Plug. Universal 7-Pin Heavy Duty Plug For Vehicles equipped with 7-Way Trailer Connectors. Installation Instructions and Product Warranty EZ-R7 T-Plug Universal 7-Pin Heavy Duty Plug For Vehicles equipped with 7-Way Trailer Connectors Installation Instructions and Product Warranty Professional Installation Required Thank you for purchasing

More information

JANUARY 2015 NOMENCLATURE. TOOLS REQUIRED 3/8" & 7/16" Can wrench or socket 1/4 Nut driver or screwdriver Snips Fiber optic cable opening tools

JANUARY 2015 NOMENCLATURE. TOOLS REQUIRED 3/8 & 7/16 Can wrench or socket 1/4 Nut driver or screwdriver Snips Fiber optic cable opening tools JANUARY 2015 COYOTE Dome Closure 6-1/2" x 17" Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED TM product before application. 1 2

More information

COYOTE 9.5" x 19" (292 mm x 509 mm) Dome Closure

COYOTE 9.5 x 19 (292 mm x 509 mm) Dome Closure AUGUST 2012 COYOTE 9.5" x 19" (292 mm x 509 mm) Dome Closure Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application.

More information

Fiber Connector Shelf (CCS)

Fiber Connector Shelf (CCS) Corning Cable Systems Standard Recommended Procedure (SRP) 003-595 Issue 3, May 2007 Page 1 of 6 Fiber Connector Shelf (CCS) Table of Contents 1. General... 1 2. Precautions... 1 3. Components... 2 4.

More information

COYOTE Dome Closure 6.5" x 22" Kits. COYOTE Dome Closure 6.5" x 22" for Buffer Tube Applications. Includes: (2) Grommets, (1) Buffer

COYOTE Dome Closure 6.5 x 22 Kits. COYOTE Dome Closure 6.5 x 22 for Buffer Tube Applications. Includes: (2) Grommets, (1) Buffer JANUARY 2015 COYOTE Dome Closure 6.5" x 22" Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application. 1 2 3 6

More information

COYOTE Terminal Dome Closure 6.5" x 22"

COYOTE Terminal Dome Closure 6.5 x 22 FEBRUARY 2015 COYOTE Terminal Dome Closure 6.5" x 22" Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application.

More information

Fiber Optic Splice Module

Fiber Optic Splice Module .COM 2016 O 24 Fiber Optice Splice Module in open position INSTALLATION INSTRUCTIONS Fiber Optic Splice Module Part Numbers: FHD-FOSMF, FHD-FOSMM 12 Fiber Optice Splice Module in open position Contents:

More information

PT8420 Cable Actuated Sensor Industrial ma 0..20mA

PT8420 Cable Actuated Sensor Industrial ma 0..20mA PT8 Cable ctuated Sensor Industrial.. m..m bsolute Linear Position to 6 inches (5 mm) luminum or Stainless Steel Enclosure Options VLS Option to Prevent Free-Release Damage IP68 / NEM 6 Hazardous rea Certification

More information

COYOTE LCC (Low Count Closure)

COYOTE LCC (Low Count Closure) PLP Feature Focus 2009 Preformed Line Products OCTOBER 2012 Film available at www.preformed.com COYOTE LCC (Low Count Closure) Be sure to read and completely understand this procedure before applying product.

More information

3M Closure System 2-Type Cover (505)

3M Closure System 2-Type Cover (505) 3M Closure System 2-Type Cover (505) Installation Instructions May 2009 78-8140-1009-2-B Contents 1.0 3M Closure Kit 2-Type Contents...3 2.0 Cover Installation...4 3.0 Closure Re-entry...6 4.0 Accessories...9

More information

3M Cold Shrink QT-III Silicone Rubber Three-Core Termination Kits

3M Cold Shrink QT-III Silicone Rubber Three-Core Termination Kits 3M Cold Shrink QT-III Silicone Rubber Three-Core Termination Kits With High-K Stress Relief For 3-Conductor Type G (Ground Wire), Copper Tape Shield, Armored Cables 7600-S-3G Series Instructions IEEE Std.

More information

SPC-P Smart Power Connection with Temperature Monitoring Transmitter Pipe Mounted Installation Instructions

SPC-P Smart Power Connection with Temperature Monitoring Transmitter Pipe Mounted Installation Instructions SPC-P Smart Power Connection with Temperature Monitoring Transmitter Pipe Mounted Installation Instructions SPC-P with Pyrotenax MI heating cable using required MI cable grounding kit SPC-P with Raychem

More information

OFS 400A FIBER OPTIC INTERCONNECT Instruction Sheet UNIT (FOIU) Comcode INSTALLATION

OFS 400A FIBER OPTIC INTERCONNECT Instruction Sheet UNIT (FOIU) Comcode INSTALLATION OFS 400A FIBER OPTIC INTERCONNECT 636-299-109-01 Instruction Sheet UNIT (FOIU) Comcode 846 586 212 INSTALLATION This instruction sheet covers the 400A1 (106266901) and 400A2 (106414170) Fiber Optic Interconnect

More information

LBB ULTRA-PRECISION GAGE HEADS

LBB ULTRA-PRECISION GAGE HEADS s LBB ULTRA-PRECISION GAGE HEADS SPECIFICATIONS Spring and pneumatic extend versions Linear ball bearing front end Extremely long life cycle 0.000004 inch [0.1μm] repeatability ±0.02 to ±0.2 inch [±0.5

More information

Required Tools: Phillips screw driver to remove original soft top. Torx sockets are required to completely remove the original soft top hardware.

Required Tools: Phillips screw driver to remove original soft top. Torx sockets are required to completely remove the original soft top hardware. RAMPAGE P R O D U C T S Installation Instructions Part number 1099XX, Frameless Soft Top for 2 door Jeep Wrangler JK 2007- NOTE: Installation of the top in warm weather is optimal for ease of installation.

More information

DODGE SLT Installation Instructions

DODGE SLT Installation Instructions 1994-97 DODGE SLT 40-20-40 Installation Instructions Step 1. Driver and Passenger Bottoms/DB&PB: All the parts of the seat cover are labeled inside. Use the seat cover piece identification chart to ID

More information

SWING DOOR SOFT ENCLOSURE (part# 16733)

SWING DOOR SOFT ENCLOSURE (part# 16733) 800-643-7332 americanlandmaster.com This kit is for use with all fullsize, 2 passenger ALM utility vehicles. SWING DOOR SOFT ENCLOSURE (part# 16733) NOTE TOOLS REQUIRED Drill 1/4 Drill Bit 7/16 Wrench

More information

Be Strong. NS 200X. Assembly Manual. Model: NS 200X. P/N: Rev A (10/04/2006)

Be Strong. NS 200X. Assembly Manual. Model: NS 200X. P/N: Rev A (10/04/2006) Be Strong. Assembly Manual NS 00X Model: NS 00X P/N: 00-700 Rev A (0/0/00) TABLE OF CONTENTS Before You Assemble... 3 Product Specifications... Product Features... Parts List / Box Contents... 5 Exploded

More information

Volition. VF-45 Quick Install kit. and Maintenance Cleaning Kit. 3Innovation

Volition. VF-45 Quick Install kit. and Maintenance Cleaning Kit. 3Innovation Volition VF-45 Quick Install Kit and Maintenance Cleaning Kit O b D s oc ol e um te en t COOL HAND TOOLS. VF-45 Quick Install kit Get your hands on a VF-45 Quick Install Kit from 3M and you will have everything

More information

FL2000 Termination/Splice Panels User Manual

FL2000 Termination/Splice Panels User Manual FL2000 Termination/Splice Panels User Manual Content Page INTRODUCTION... 1 Revision History... 1 List of Changes... 1 Trademark Information... 2 Related Publications... 2 Admonishments... 2 General Safety

More information

POWERHEAT TYPE AHT TERMINATION INSTRUCTIONS. Ref TK/AHT Issue C Date 16 August 1999

POWERHEAT TYPE AHT TERMINATION INSTRUCTIONS. Ref TK/AHT Issue C Date 16 August 1999 STOCKPORT, ENGLAND, TEL: 0161-430 8333 POWERHEAT TYPE AHT TERMINATION INSTRUCTIONS PLEASE READ THE INSTRUCTIONS BEFORE PROCEEDING Recommended Tools ANNEX B Ref TK/AHT Issue C Date 16 August 1999 Heavy

More information

Pretium Wall-Mountable Housing (PWH-02P/-04P/- 06P/-12P and FZB-02P-JB)

Pretium Wall-Mountable Housing (PWH-02P/-04P/- 06P/-12P and FZB-02P-JB) 1. Precautions 2. Carton Contents Pretium Wall-Mountable Housing OR Fiber Zone Box (FZB-02P-JB) PWH-02P and FZB-02B-JP have: (15 inches) edge grommet (1) Laser warning label (2) Fiber identification labels

More information

Duster Deck Cover Installation Instructions

Duster Deck Cover Installation Instructions Duster Deck Cover Installation Instructions For: Jeep Wrangler, 1997-2002 Part Number: 90019 with Factory Original Soft Top DO NOT INSTALL THIS PRODUCT ON ANY VEHICLE OTHER THAN THOSE LISTED ABOVE. This

More information

CM52 Network Protector with Arc Flash Reduction Module

CM52 Network Protector with Arc Flash Reduction Module Contents Description Page 1: General.............................. 2 2: Maintenance Mode Settings.............. 2 3: Arming Maintenance Mode.............. 2 4: Remote Indicator....................... 2

More information

THE SB01 SPLICE ENCLOSURE NOW INCLUDES A LID GASKET THAT DOES NOT REQUIRE RTV APPLICATION.

THE SB01 SPLICE ENCLOSURE NOW INCLUDES A LID GASKET THAT DOES NOT REQUIRE RTV APPLICATION. THE SB01 SPLICE ENCLOSURE NOW INCLUDES A LID GASKET THAT DOES NOT REQUIRE RTV APPLICATION. DO NOT APPLY RTV TO THE GASKET WHEN SEALING THE SB01 SPLICE ENCLOSURE. SEE SECTION 18 FOR UPDATED INSTRUCTIONS.

More information

COYOTE Dome Cross-Connect Closure 6-1/2" x 22"

COYOTE Dome Cross-Connect Closure 6-1/2 x 22 FEBRUARY 2015 COYOTE Dome Cross-Connect Closure 6-1/2" x 22" Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application.

More information

THE SB01 SPLICE ENCLOSURE NOW INCLUDES A LID GASKET THAT DOES NOT REQUIRE RTV APPLICATION.

THE SB01 SPLICE ENCLOSURE NOW INCLUDES A LID GASKET THAT DOES NOT REQUIRE RTV APPLICATION. THE SB01 SPLICE ENCLOSURE NOW INCLUDES A LID GASKET THAT DOES NOT REQUIRE RTV APPLICATION. DO NOT APPLY RTV TO THE GASKET WHEN SEALING THE SB01 SPLICE ENCLOSURE. SEE SECTION 10 FOR UPDATED INSTRUCTIONS.

More information

Cargo Cover. Installation Instructions. For: Wrangler Part Number: Installation Tips WARNING

Cargo Cover. Installation Instructions. For: Wrangler Part Number: Installation Tips WARNING Cargo Cover Installation Instructions For: Wrangler 1997-2002 Part Number: 41825 Note: This kit is designed to be installed on vehicles equipped with a Production Soft Top Only. WARNING This product is

More information

3M Ladder Kit 3M710/MS 2 -TMK-LK

3M Ladder Kit 3M710/MS 2 -TMK-LK 3M Ladder Kit 3M710/MS 2 -TMK-LK Instructions 1.0 Summary The 3M Ladder Kit 3M710/MS2-TMK-LK is intended for mounting a communication line splicing system to a fiberglass extension ladder. 2.0 Kit Contents

More information

3M Cross-Connect Cabinets 4220SVC and 4220SVE Tall Skirt Installation Guide

3M Cross-Connect Cabinets 4220SVC and 4220SVE Tall Skirt Installation Guide 3M Cross-Connect Cabinets 4220SVC and 4220SVE Tall Skirt Installation Guide Installing Tall Skirt on SVC and SVE cabinets Instructions July 2016 78-0015-3067-0 2 July 2016 78-0015-3067-0 Contents 1. General

More information

COYOTE 9.5" x 19" (292 mm x 509 mm) Cross-Connect Dome Closure

COYOTE 9.5 x 19 (292 mm x 509 mm) Cross-Connect Dome Closure AUGUST 2013 COYOTE 9.5" x 19" (292 mm x 509 mm) Cross-Connect Dome Closure Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED TM product

More information

F-150 Super Crew W/Opening Console Installation

F-150 Super Crew W/Opening Console Installation 2004-08 F-150 Super Crew 40-20-40 W/Opening Console Installation Step 1. Driver and Passenger Tops/DT&PT: All the parts of your seat cover are labeled inside. Use the Seat Cover Piece Identification Chart

More information

ELB ELB

ELB ELB ELB-35-600 ELB-35-610 600A T-Body Elbow Connectors for Copper Tape (CT), Jacketed Concentric Neutral (JCN), and Concentric Neutral (CN) cables up to 35kV class Safety Instructions When installing electrical

More information

3M Cold Shrink Splice Kit QS-III 5536A

3M Cold Shrink Splice Kit QS-III 5536A 3M Cold Shrink Splice Kit QS-III 5536A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric

More information

HTP PTP/ PTJ Power Connection Kit for Pipes

HTP PTP/ PTJ Power Connection Kit for Pipes HTP 1548-40PTP/1548-40PTJ Power Connection Kit for Pipes For use with Dekoron 2700 and 2300 Families of Heating Cables. 1548-81HTJ/81HTP for use with 2000 Series Heating Cables. Installation Instructions

More information

Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY.

Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY. Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY. The simplex connector kit consists of a connector assembly, short boot, and tubing. The tubing is used with 250

More information

Raychem CSJA Safety Instructions. Safety Instructions. Customer Service. Kit Contents. Installation Instructions

Raychem CSJA Safety Instructions. Safety Instructions. Customer Service. Kit Contents. Installation Instructions Raychem CSJA 1521 Cold-Shrinkable Splice for single core polymeric insulated (XLPE-EPR) cables up to 15kV for tape, wire, Unishield, LC shield, JCN, and flat strap neutral cable UniShield is a trademark

More information

Features: Use the selection chart below to choose the Splice Case and splice tray organizer which meet the requirements for your application.

Features: Use the selection chart below to choose the Splice Case and splice tray organizer which meet the requirements for your application. FIBERLIGN Organizers For s (Protected and ) and Mechanical s FIBERLIGN Fiber Optic Organizers are designed to help organize, secure, support and protect delicate optical fibers before, during and after

More information

QT-III Cold Shrink Silicone Rubber

QT-III Cold Shrink Silicone Rubber QT-III Cold Shrink Silicone Rubber 7600-T-3RJS Series 3/C Cabinet Termination Instructions Kit Contents: 3ÑSilicone Rubber Phase Re-jacketing Sleeve Assembly 3ÑCold Shrink Silicone Rubber Termination Assembly

More information

Universal Bench-top Conveyor OPERATOR S GUIDE

Universal Bench-top Conveyor OPERATOR S GUIDE OPERATOR S GUIDE DISCLAIMER LIABILITY LIMITATION: The Buyer of this product accepts full responsibility and understanding for the terms and specifications set forth herein. Con-Trol-Cure makes no claim,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Thank you for purchasing TONNOSPORT Roll-Up Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship. With proper care, your cover

More information

FREEZSTOP MICRO SYSTEM. Freeze Protection of Pipework

FREEZSTOP MICRO SYSTEM. Freeze Protection of Pipework FREEZSTOP MICRO SYSTEM Freeze Protection of Pipework Prevent Burst or Blocked Pipes The Problem Thermal insulation alone will not prevent freezing of pipes. For example, a 3/4 pipe having 25mm thick insulation

More information

INSTRUCTIONS: JOEY 30 CART (MK2)

INSTRUCTIONS: JOEY 30 CART (MK2) INSTRUCTIONS: JOEY 30 CART (MK2) Congratulations on your purchase. Follow these instructions for easy and fast set-up of your Joey 30 Cart. For video instructions, go to https://vimeo.com/144317620 Warranty:

More information

JBS-100-STB Single Entry Power Connection with Junction Box Installation Instructions

JBS-100-STB Single Entry Power Connection with Junction Box Installation Instructions JBS-100-STB Single Entry Power Connection with Junction Box Installation Instructions Description The JBS-100-STB is a NEMA 4X rated power connection kit. It is designed for use with Raychem BTV-CR, BTV-CT,

More information

DOCUMENT OBSOLETE. Volition. VF-45 Socket Termination and Maintenance Cleaning Kits COOL HAND TOOLS. CLEAN UP YOUR ACT. VF-45 Socket Termination Kit

DOCUMENT OBSOLETE. Volition. VF-45 Socket Termination and Maintenance Cleaning Kits COOL HAND TOOLS. CLEAN UP YOUR ACT. VF-45 Socket Termination Kit Volition VF-45 Socket Termination and Maintenance Cleaning Kits COOL HAND TOOLS. VF-45 Socket Termination Kit Get your hands on a Volition VF-45 Socket Termination Kit from 3M and you will have everything

More information

TABLE OF CONTENTS 10.0 LIMITED WARRANTY

TABLE OF CONTENTS 10.0 LIMITED WARRANTY 10.0 LIMITED WARRANTY ELECTROMATIC Equipment Co., Inc. (ELECTROMATIC) warrants to the original purchaser that this product is of merchantable quality and confirms in kind and quality with the descriptions

More information

LSW Connector Module User Manual

LSW Connector Module User Manual LSW Connector Module User Manual Content Page INTRODUCTION............................................................................. 2 Revision History........................................................................

More information

Deluxe Hitch 3-Bike Rack Instructions for Part # BC-3581

Deluxe Hitch 3-Bike Rack Instructions for Part # BC-3581 General Guidelines Deluxe Hitch 3-Bike Rack Instructions for Part # BC-3581 It is the user s responsibility to read and follow all instructions. Keep these instructions with the product at all times and

More information

19 floor rack with steel door

19 floor rack with steel door 2015 Telecommunication rack systems HETEL 1 19 floor rack with steel door Rack width 600 mm Rack width 800mm General features include a metal frame, 19 rails, roof, side and rear panels, door and plinth

More information

Section 3 FIBERLIGN Closure Series

Section 3 FIBERLIGN Closure Series FIBERLIGN Closure Series: Section 3 Section 3 FIBERLIGN Closure Series Table of Contents Page FIBERLIGN s...3-2 FIBERLIGN Organizers...3-3 FIBERLIGN UNI-CLOSURE...3-8 FIBERLIGN Fiber Safe...3-11 FIBERLIGN

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Thank you for purchasing VANISH Roll-Up Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship. With proper care, your cover

More information

JBM-100-STB NEMA 4X-rated connection kit Installation Instructions

JBM-100-STB NEMA 4X-rated connection kit Installation Instructions JBM-100-STB NEMA 4X-rated connection kit Installation Instructions Power Connection, Powered Splice, Powered Tee, Dual Power Connection, Splice or Tee with Junction Box Approvals Hazardous Locations CLI,

More information

NEMA-Rated Fiber Optic Wallmount Enclosure. Protects your fiber cabling in a damp environment.

NEMA-Rated Fiber Optic Wallmount Enclosure. Protects your fiber cabling in a damp environment. JPM4001A-R2 NEMA-Rated Fiber Optic Wallmount Enclosure Protects your fiber cabling in a damp environment. BLACK BOX Single rubber gasket door has a hex nut security lock. Cable enters or exits the enclosure

More information