- PDF Free Download

Size: px

Start display at page:

Download ""

Annice Harrell
5 years ago
Views:

1 OPYRIGHT 2013 American Autowire / Factory-Fit Used with express permission of American Autowire / Factory- Fit Page Rev 0.0 6/18/2015

UNSEALED ONNETORS The connectors, sockets, wires, terminals and tools,

that are available, to help with your installation, from the American

SEALED WEATHER PAK ONNETORS OPTIONAL Add-On Equipment: 500070 500321

500723 Battery Trunk Mount Kit, Top Post (pictured) 500724 Battery

Post (pictured) 500725 Battery Under Hood Mount Kit, Top Post 500192

500073 500315 D Start Mount Bolt Negative battery cable not included in

36050 LAMP SOKETS - PLASTI 510157 510156 500314 510155 510154 A B

rimping Star Tool (this tool is included, in the four Battery Kits

Front Parking Light Right Front Parking Light ooling Fan Interior

Gauges Air onditioning Door Jambs Wipers Rear Ground System Left Tail

Full Vehicle Grounding Kit 35900 Page 2 18995 510152-510157 Split Braid

2 UNSEALED ONNETORS The connectors, sockets, wires, terminals and tools, shown on this page, are just a small sample of the many accessories that are available, to help with your installation, from the American Autowire atalog. SEALED WEATHER PAK ONNETORS OPTIONAL Add-On Equipment: B A B A B A Battery Trunk Mount Kit, Top Post (pictured) Battery Trunk Mount Kit, Side Post Battery Under Hood Mount Kit, Side Post (pictured) Battery Under Hood Mount Kit, Top Post A B All opper Ground System No Frame Rail Reinforcing Steel lip D Start Mount Bolt Negative battery cable not included in kit Must be purchased separately LAMP SOKETS - METAL LAMP SOKETS - PLASTI A B Alternator onnection Kit - High Amp Output Battery rimping Star Tool (this tool is included, in the four Battery Kits above) Front Ground System Horn Left Headlight Right Headlight Left Front Parking Light Right Front Parking Light ooling Fan Interior Ground System Headlight Switch Third Brake Light Radio Steering olumn Gauges Air onditioning Door Jambs Wipers Rear Ground System Left Tail Light Right Tail Light Gas Tank License Plate Light Fuel Pump Full Vehicle Grounding Kit Page Split Braid Wiring Harness Wrapping Weatherproof Universal Relay Kit Lifeline Memory Retention Module ourtesy Light onnection Kit Rev 0.0 6/18/2015

START HERE! PLEASE READ THIS BEFORE STARTING INSTALLATION! This wiring kit is designed for ease of installation.

Use an appropriate crimping tool, which folds the wings of the open barrell terminals down into the wire, as

If you use our crimping tools and correctly crimp the included terminals, soldering is not necessary.

Our factory crimped terminations are installed by GM approved five ton presses, and soldering these terminations

The F crimp, in a cross section, will look like the illustration below, when done correctly.

to help with your terminal crimping. These hand tools are available, for purchase or rental.

AAW p/n 510585 OEM small terminal crimping tool (18-14 gauge) AAW p/n 510586 OEM large terminal crimping tool

your web browser, to go directly to the video: https://www.youtube.com/watch?v=jagedovl-co Youtube hannel: www.

3 START HERE! PLEASE READ THIS BEFORE STARTING INSTALLATION! This wiring kit is designed for ease of installation. Please read the guidelines below, BEFORE STARTING your installation, to guarantee a successful job. Use an appropriate crimping tool, which folds the wings of the open barrell terminals down into the wire, as shown on this page. If you use our crimping tools and correctly crimp the included terminals, soldering is not necessary. If you are unsure about a particular crimp, soldering is recommended. Our factory crimped terminations are installed by GM approved five ton presses, and soldering these terminations is not necessary. The terminals that we supply in our kits, utilize what is known as an F crimp. The F crimp, in a cross section, will look like the illustration below, when done correctly. end view of un-crimped terminal proper crimp of terminal wire core We carry the following crimping hand tools, to help with your terminal crimping. These hand tools are available, for purchase or rental. AAW offers a great terminal crimping video entitled Proper rimping Video. It can be viewed by visiting YouTube. AAW p/n OEM small terminal crimping tool (18-14 gauge) AAW p/n OEM large terminal crimping tool (12-8 gauge) AAW p/n Weather Pack/Metri Pack crimping tool (18-12 gauge) Type the following address into your web browser, to go directly to the video: Youtube hannel: STEP 1: DISONNET YOUR BATTERY: Disconnect the battery, before installing the wiring kit, to prevent any accidental shorting caused by loose bare wire ends. Page 3 If you have any questions concerning this or any of our products, please feel free to call us at Rev 0.0 6/18/2015

4 STEP 2: START INSTALLING KIT: This kit is broken down into individual sections, that are identified by a letter printed on the enclosed sheets, visible through each bag. The order of installation and the pages with their installation instructions, are shown below: Table of ontents: Bags: Pages: Sections: LINEATWATERPROOF 200ABA 5, 6 Power Subkit - This harness contains: - Starter solenoid connections. - Ignition switch connections. - Main ircuit Breaker connections. - Alternator connections. - Neutral safety switch connections. - Battery connections. GRAY BLAK Severe Duty Fuse Box LOADAUircuit Breaker B 7-13 Main Subkit - This Harness contains: - Wiper Feed. - Heater/A Feed. - Headlight Switch Feed. - Horn Feed. - Gauge Feed. - Reverse Light Switch Feed. - lock Feed. - Brake Light Switch Feed. - Radio Feed. - Turn Signal/Hazard Light Feed. - Miscellaneous Ignition Feeds. Headlight Switch XDimmer Switch D 12, 13 10, 11 Headlight Kit - This Harness contains: - Headlight Switch. - ourtesy Light connections. - Headlight connections. - Dimmer Switch. - Parking Light connections. Turn Signal Kit - This Harness contains: - Turn Signal connections. - Third Brake Light connection. - Brake Switch connection. - Turn Signal Indicator connections. POWER SUBKIT Severe Duty Universal Kit bag A MAIN SUBKIT Severe Duty Universal Kit bag B HEADLIGHT KIT Severe Duty Universal Kit bag E 14 Gauge Kit - This Harness contains: - Gauge connections for aftermarket gauges. - Electronic Speedometer connections. - Indicator Lights connections. TURN SIGNAL KIT Severe Duty Universal Kit bag D GAUGE KIT Severe Duty Universal Kit bag E Page Rev 0.0 6/18/2015

LINAETLOADAUPower Harness installation instructions: length cut, from Power Kit IRUIT Neutral Safety to Ignition FIND THESE XREAR BREAKER Switch Switch PARTS, IN BAG A.

) (ring terminal, 7 pcs.) 12V this wire, not supplied ALTERNATOR XBATTERY E F (ring terminal, large stud, smaller wire, 3 pcs.) (ring terminal, medium stud, large wire, 2 pcs.

5 LINAETLOADAUPower Harness installation instructions: length cut, from Power Kit IRUIT Neutral Safety to Ignition FIND THESE XREAR BREAKER Switch Switch PARTS, IN BAG A. LOADWATERPROOF AT200ABAULINEthis wire, not supplied starter solenoid purple WATERPROOF 200ABFRONT STARTER SOLENOID E S I B STARTER purple A B ircuit Breaker (female terminal, 5 pcs.) (ring terminal, 7 pcs.) 12V this wire, not supplied ALTERNATOR XBATTERY E F (ring terminal, large stud, smaller wire, 3 pcs.) (ring terminal, medium stud, large wire, 2 pcs.) length cut, from Power Kit D F this wire, not supplied D (shrink tubing, 5 pcs.) (ring terminal, medium stud, smaller wire, 2 pcs.) (splice clip, 2 pcs.) Page 5 these parts are not supplied; see available Alternator onnection Kit , on page Rev 0.0 6/18/2015

6 Power Harness Gray Input onnector and Black Input onnector installation instructions: REAR IGNITION SWITH B A see page 15, for Battery accessory connections see page 2, for optional Lifeline Memory Retention Module Accessories E LOADWATERPROOF AT200AB XGRAYBLAK AULINEE IRUIT BREAKER Gray Input onnector Black Input onnector E pink Accessory FUSE BOX Neutral Safety Switch Ignition 10ga purple brown Battery Ignition Feed 12ga DISTRIBUTOR, pink rank Accessory Ignition Battery Ring terminals and Push-on female terminals, can be found in Bag A, to make connections to your ignition switch. Battery wire length, cut from Power Kit See Detail A Slide heat shrink tubing, over pink 10ga wire, prior to terminating both ends. rimp splice clip, to both pink wires, as shown, then solder crimp. Slide shrink tubing over splice clip and shrink to cover. 12ga 10ga Detail A FRONT Page Rev 0.0 6/18/2015

7 RONTREAR RUNNING LIGHTFGRAY BLAK Gray Output onnector Main Harness - Gray Output onnector installation instructions: Wiper Feed orange GRAY BLAK G K Gray Output onnector 12v Battery L 12v Battery Fused H HEADLIGHT SWITH J FIND THESE PARTS, IN BAG. H WIPERS FIND THIS PART, IN BAG B. G HEADLIGHT SWITH GAUGE LUSTER TSY PARK LIGHTS PARK LIGHTS DIMMER SW FEED DASH DASH LIGHTS LIGHTS (Headlight, Parking Light Harness; Reference) WIPERS GAUGE LUSTER (female terminal, large 3, pc.) REAR(headlight switch, 1 pc.) Gauge Feed J K Page 7 see page 14, for Gauge connections L (female terminal, small,3 pc.) Rev 0.0 6/18/2015

8 FRONTMain Harness - Gray Output onnector installation instructions: Fan Relays, Lighting Relays, Electronic ontrollers, etc. RGRAY BLAK LOK RADIO REAGRAY BLAK LOK G lock Bat tan Radio RADIO Fan Relays, Lighting Relays, Speedometer power (see page 15), Electronic ontrollers, etc. 12v Ignition 12v Ignition Page Rev 0.0 6/18/2015

9 FRONTBlack Output onnector GRAY BLAK REAMain Harness - Black Output onnector installation instructions: HEATER / A BLOWER REVERSE LIGHT SWITH HORN SWITH BRAKE LIGHT SWITH RHORN AA GRAY BLAK HEATER / A BLOWER FIND THESE PARTS, IN BAG B. Black Output onnector M Heater/A Feed brown M HORN dk green Horn orange Brake Switch switch input lt green BRAKE LIGHT SWITH Reverse Light Switch Horn Relay Ground REVERSE LIGHT SWITH HORN SWITH AA (ring terminal, internal tooth, 2 pcs.) lt green see page 13 Page 9 You can pass these wires, through connectors N and P, on page Rev 0.0 6/18/2015

10 FRONTGRAY BLAK REATurn Signal Harness installation instructions: FRONT TURN SIGNALS onnect turn signal light wire, to turn signal light filament. onnect turn signal light wire, to turn signal light filament. dk blue Left Turn purple Turn Switch Feed Turn Sw Hazard brown lt blue T T GRAY BLAK M LEFT DASH IND RIGHT DASH IND Use empty D cavity, in connectors N and P, to connect Horn wires, on page 9 N dk green to Brake Light Switch - see page 11 Left Rear P R R to Gauge indicators - see page 14 Right Rear Left Front Turn (lt blue) Right Front Turn (dk blue) Turn Switch Hazard (brown) Turn Switch Feed (purple) Left Rear Turn (yellow) Right Rear Turn (dk green) Brake Switch (white) RRight Turn N P R T FIND THESE PARTS, IN BAG D. A B D E F G H J K L M N P P N M L K J H G F E D LEFT FRONT TURN RIGHT FRONT TURN LEFT DASH IND RIGHT DASH IND LEFT REAR TURN RIGHT REAR TURN BRAKE SW THIRD BRAKE LIGHT (Turn Signal Harness; Reference) (Pack-con 14-way male connector, 1 pc.) (Pack-con male terminal, 10 pcs.) (Pack-con female terminal, 6 pcs.) Page 10 STEERING OLUMN and DASH Rev 0.0 6/18/2015

11 RONTTurn Signal Harness installation instructions: THIRD BRAKE LIGHT GRAY BLAKFRGRAY BLAK REAonnect turn signal light wire, to turn signal light filament. M N See page 10 REAR TURN SIGNALS T See page 10 T BRAKE LIGHT SWITH switch outputs dk green Third Brake Light (optional) Right Rear Left Rear onnect turn signal light wire, to turn signal light filament. Page 11 LIGHT BLUE WIRE, FROM BAG D Rev 0.0 6/18/2015

12 GRAY BLAK Headlight Harness installation instructions: Headlight onnect parking light wire, to parking light filament. brown PARKING LIGHTS V V W Y W W High Beam Y W tan Low Beam Parking Lights orange GRAY BLAK L K gray L H H ourtesy Ground, see page 13 DASH LIGHTS HI BEAM INDIATOR LIGHT U J RONTto Gauge luster Harness - see page 14 connector, 2 pcs.)ffind THESE PARTS, IN BAG. H K J U W (dimmer switch, 1 pc.) TSY PARK LIGHTS REAR PARK RUNNING LIGHTSLIGHT DIMMER SW FEED DASH DASH LIGHTS LIGHTS HI BEAM INDIATOR LIGHT HEADLIGHT - HI BEAM HEADLIGHT - LOW BEAM LIENSE LIGHT (Headlight, Parking Light Harness; Reference) (headlight switch, 1 pc.) (single female terminal, large, 2 pc.) (single female terminal, 6 pcs.) V L (single female terminal, small, 3 pcs.) (3-way female Y (double female terminal, 2 pcs.) REARHEADLIGHTS and FRONT Page 12 Headlight lt green brown Rear Running Lights Rev 0.0 6/18/2015

13 REARREAR RUNNING, REVERSE ROHeadlight Harness installation instructions: OURTESY LIGHTS and LIENSE PLATE LIGHTS GRAY BLAK FNTGRAY BLAK You can use Battery output, from the Green accessory connector. Battery 12v orange ourtesy Light onnection Kits, are available from AAW; see page 2 onnect rear running light wire, to rear running light filament. ourtesy Ground ourtesy light socket Lights K L H REVERSE LIGHT SWITH Reverse Lights License see page 12 L brown U Rear Running Lights lt green onnect rear running light wire, to rear running light filament. Page Rev 0.0 6/18/2015

14 Gauge luster Harness (aftermarket gauges) installation instructions: TYPIAL AFTERMARKET GAUGE ONNETIONS (BLADE TYPE ONNETIONS SHOWN) LEFT TURN IND HIGH BEAM IND RIGHT TURN IND LEFT DASH IND RIGHT DASH IND A B B A LEFT DASH IND RIGHT DASH IND lt blue dk blue HI BEAM INDIATOR LIGHT D D HI BEAM INDIATOR LIGHT lt green VSS Ground and VSS Signal (yellow and purple wires), must be twisted together, their entire lengths. see page 8 VSS VSS SIGNAL 12V IGNITION OIL --> TAH VSS POWER BB A B D E F If you have a tachometer, insert these terminals into the empty E cavities, in both connectors. VSS VSS SIGNAL VSS POWER SPEEDO POWER It is best to consult the speedometer manufacturer s instructions, if you have any questions. OIL --> TAH black (ground) pink/white Volts GRD TURN SIGNAL AND HI-BEAM LIGHT ONNETIONS black/white I purple/white Tachometer yellow purple VSS GRD VSS Ground and VSS Signal (yellow and purple wires), must be twisted together, their entire lengths. GRD Oil S I Yellow VSS Ground onnect to VSS - on speedometer. Purple VSS Signal onnect to VSS input on speedometer. Purple/White VSS Power onnect to 12V power on speedometer. Black/White Speedo Ground onnect to ground on speedometer. Pink/White Speedo Power onnect to 12v power on speedometer. NOTE: This wire will double onto the same stud as the Purple/White VSS power wire from above. white Water GRD I S GRD S I black (ground) SPDO GRD S 12v I Speedometer Fuel GRD I S pink (12V ignition) see page 7 GAUGE FEED WATER TEMP SENDER OIL PRESSURE SENDER DASH LIGHTS BB A B D E F WATER TEMP SENDER OIL PRESSURE SENDER DASH LIGHTS 12V IGNITION GAS GAUGE dk green pink (12V ignition) dk blue GAUGE ONNETIONS tan GAS GAUGE gray (dash lights) gray (dash lights) Page 14 BB FIND THIS PART, IN BAG B. (Pack-con female terminal, 2 pcs.) Water black (ground) Volts Tachometer Speedometer LIGHT ONNETIONS Oil Fuel Rev 0.0 6/18/2015

Green Accessory onnector installation instructions: If you plan on using the Battery Outputs (fuse locations F2-F5 ), this Red Accessory wire must be connected; see page 6.

15 Green Accessory onnector installation instructions: If you plan on using the Battery Outputs (fuse locations F2-F5 ), this Red Accessory wire must be connected; see page 6. If you are not using these outputs, this Red Accessory wire can be removed. Gray Input onnector Accessories To remove this Accessory wire, first remove the wire retention clip, from the wire side of the connector... retention clip then, facing the mating end of the connector and using a small thin-bladed device, undue the retention tab of the terminal and pull the wire from the connector. mating end of connector Examples of possible user circuits - Lights: ourtesy, Underhood, etc. - Electronic Modules/EU s - igarette Lighters - USB charging outputs - Radios/Bs - GPS units - Spot Lights - Fuel Pumps/Fuel Pump Relays - Electronic Modules - Fan Relays Pin Location 4A 4B 4G 4H 4 4F 4D 4E Output Type Optional Battery Feed* Optional Battery Feed* Optional Battery Feed* Optional Battery Feed* Optional Accessory Feed Optional Accessory Feed Optional Ignition Feed Optional Ignition Feed Fuse * The Red Accessory wire, in the Gray Input onnector, must be connected, in order to use these circuits. undue terminal retention tab, in this area F4 F5 F3 F2 F7 F6 F8 F9 FIND THESE PARTS, IN BAG B. ircuits are live, in these ignition switch positions All A (Accessory ) ON / IGN / RUN GRAY BLAK 4B 4A 4H 4G (8-way sealed female connector, 1 pc.) (cable seal retainer, 1 pc.) 4 4F (cable seal, gray, 8 pcs.) 4D 4E mating face of green accessory connector 4B 4A B A H G 4H 4G (cable seal, blue, 8 pcs.) (cable seal, green, 8 pcs.) Page 15 apply supplied decal, to top of fuse box 4 D E 4D 4E wiring end of connector F 4F (connector cavity plug, green, 8 pcs.) (female terminal, 10 pcs.) (four different gauges, of coiled wire; 400 inches) Rev 0.0 6/18/2015

16 STEP 3: REONNET YOUR BATTERY: When you have completed the installation and are ready to reconnect the battery, make sure that the following electrical system grounds are in place: A. Battery is grounded to the ENGINE BLOK. B. Battery is grounded to the frame.. Engine block is grounded to the frame. D. Body is grounded to the frame. STEP 4: HEK ALL ELETRIAL FUNTIONS: Any non-functioning items should be checked for proper installation. Any problems with your wiring and electrical circuit functions, should be addressed to American Autowire Systems, Inc. as soon as possible, to avoid any warranty problems. If you have any questions concerning this or any of our products, please feel free to call us at Page Rev 0.0 6/18/2015

Classic Update Series

Classic Update Series START HERE! PLEASE READ THIS BEFORE STARTING INSTALLATION! This wiring kit is designed for ease of installation. Please read the guidelines below, BEFORE STARTING your installation to guarantee a successful