Custom Dynamics Technical Bulletin
|
|
- Felicity Ferguson
- 5 years ago
- Views:
Transcription
1 Custom Dynamics Technical Bulletin Troubleshooting Connection Issues with Turn Signals This bulletin is for the purpose of helping customers solve connection/operation issues on Custom Dynamics LED replacement turn signal clusters with plug-in bases. This is applicable for multiple makes with 1156, 1157, BAZ-3 and 7507 bulb sockets. So you ve decided to upgrade your turn signals. You want added visibility for the road and to do it in style. Custom Dynamics LED turn signals give you just that. You ve received your clusters, installed them following the instructions and you just can t get them to operate correctly. We can t assume it is the product before examining the factors that can cause connectivity issues. What to do First Don t panic! There are many different variables at work here. Let s cover how to check if the cluster is working. For a cluster that wont light at all: 1. Try it in the socket on the opposite side and test function. If it still does not light, then try below. Single Ground wall [ - ] Dual 2. Test the cluster off the bike by using a 9 or 12 volt DC battery with wire leads. See Bulb base diagram right for examples of single and dual contacts. Touch the negative lead from the battery to the metal side of the cluster base. Next, touch the positive lead from the battery to the bottom contact. The cluster should light up. Now that we have confirmed that the cluster is working, we should then take a look at the environmental factors that can affect operation. Turn Power [ + ] Run/Turn Power [ + ] LED base diagrams: Left is a single contact 1156 base, the right is a dual contact Both are typical on all Harley-Davidson models. Environmental Factors There are many factors that can affect the normal operation of our LED replacement turn signal clusters. It could be a single cause or a combination of them. The most common causes that affect operation are listed in the box to the right. Keep reading as we discuss these issues and ways to correct them. Dielectric Grease Corrosion Worn Socket s Improper pin orientation Power Issues Reverse Polarity
2 Technical Bulletin - Page 2 Dielectric Grease - The LED Enemy In your turn signal housings you will most likely find a greasy substance called dielectric grease. The purpose of this grease is to insulate the bulb contacts and prevent corrosion. Many manufacturers use this in their socket housings. The only drawback to the grease is that it is an insulator, not a conductor. The grease does not conduct electric current very well at all. This environmental condition is especially bad for LEDs. So why do my stock bulbs work just fine with it, you ask? Well, a stock amber 1156 incandescent bulb handles quite a bit of current, 2.15 amps at 13.8 Volts DC to be exact. The high current of the stock bulb is enough to cross the dielectric barrier and light the bulb. When we replace the stock bulb with an LED cluster, we are reducing the current or load quite a bit going through the socket. Our LED turn signal clusters measure just.32 amps at 13.8 volts DC, a difference of almost 2 amps. Positive s Ground This is a Harley-Davidson dual contact 1157 signal socket. Note the locations of the Positive and negative contacts. These should be free of any dielectric grease for LEDs to work properly. The low current draw of the LED cluster is not enough to cross the dielectric barrier, thus, function is inhibited. The result is intermittent or no function from the cluster. So the way we remedy the issue is to remove as much dielectric grease from the housing and contacts as possible. Use a shop rag or towel with your finger and just scrape it out. You should pay close attention to the inside walls of the base as well as the positive contacts (see the photo diagrams of the bulb socket functions). Before re-installing and testing the LED cluster, read below for the next steps. Ground s Socket Corrosion This environmental condition can occur even in the presence of dielectric grease. Over time the socket contacts can become corroded, which can inhibit conductivity. To remedy the issue, even if no visible corrosion is present, use the point end of a flat head screw driver to scrape the positive contacts to ensure a good surface and that it is clear of corrosion and grease. You should also clean the LED cluster base contacts in order to clear off any transferred dielectric grease, as well as any protective film residue left on from the factory. Positive This is a Harley-Davidson Single contact 1156 signal socket. Note the locations of the positive and ground contacts. Because the ground contacts are actually the base walls, it is critical to make sure the inside surfaces are clean as well as the contact.
3 Technical Bulletin - Page 3 Worn Socket s The last step before reinstalling the LED cluster and testing, we should check the spring tension in the socket. Older bikes may occasionally develop an issue in which the spring that floats the contacts become over-compressed and prevents the socket contacts from making constant contact with the bulb base. You can diagnose this environmental issue by inserting the bulb base in the socket making sure the side pins lock, then pushing down on the base at an angle. If it pushes very easily or seems loose, then the contact spring likely needs some minor adjustment. For Bullet housings only: (see photo right) adjust the ground contact by inserting a small screw driver in behind the ground contact and very lightly prying forward. The trick is not to over extend the contact or spring, use only a small amount of leverage at a time, testing the fitment after each adjustment. Once fitment is better, test for proper operation of the LED Cluster. Ground Harley-Davidson 1157 Dual Socket with adjustment to the ground spring with small screw driver. Everything to Light Up Your Ride
4 Technical Bulletin - Page 4 Improper Pin Orientation Although most bulb bases are keyed one specific way in the socket, depending on its age and condition, it is possible to misalign the index pins and install incorrectly. All of the bulbs are designed to push in and twist to lock. The first sign that the base is not oriented properly is that it will be very difficult to push in and the base will not lock in place. The second sign would be that the cluster may illuminate full intensity all the time with no turn signal flash, if it works at all. On Dynamic Ringz clusters, the amber center will light up instead of the white ring. The main factor to be aware of for proper fitment is matching the correct index pins with the correct grooves in the socket. Below are the main bulb base types and the location of the index pins. To remedy this fitment issue, verify the correct product is being used for the application as well as making sure the index pins are aligned in the socket properly Bayonet Single, 2 index pins Keyed either way 1157 Bayonet Dual, 2 offset index pins Keyed one way Profile Profile 7507 Bayonet Single, 2 offset index pins Keyed one way BAZ-3 Bayonet Dual, 3 offset index pins Keyed one way Pro- Profile
5 Technical Bulletin - Page 5 Power Issues to the Socket If After all of the previous potential causes have been inspected for and addressed, yet the LED cluster still will not function properly, it is time to troubleshoot the wiring to the turn signal. An automotive 12 Volt test light probe is recommended for easy diagnosis of electrical issues on the bike. These can be purchased at any auto parts retailer or directly from Custom Dynamics. This will make the confirmation of power and ground easy. The way to test for power at the turn signal socket using a test light probe is as follows: 1. attach the connection clamp from the test light to the ground stud or negative battery terminal on the bike. 2. Turn the ignition on. 3. For Single contact sockets: touch the test probe to the [ + ] center contact, the test light should light up. If the light does not light, then touch the test probe to the [ - ] contact, if it lights up - you have a reverse polarity issue (see page 6 for instructions) Pictured above is a 12Volt DC automotive test probe. These can be purchased at any auto parts retailer or directly from Custom Dynamics For Dual Sockets: One [ + ] contact will have constant low intensity running power, thus the test light will light up solid. The other [ + ] contact is the turn signal, when the probe touches the contact, the test light should flash like a turn signal. 5. If the test light did not light up for any of the above, then power is not getting to the socket and further troubleshooting is required by a qualified mechanic or dealer. If power is good at the socket, continue with the ground test. Next, the way to test for good ground at the turn signal socket using a test light probe is as follows: 1. Attach the connection clamp from the test light to the positive battery terminal on the bike. 2. Turn the ignition on. 3. Touch the test light probe to the inside wall of the socket or to the negative contact spring. The test light should light up solid. 4. If the test light did not light up, there is an issue with the ground on the bike and requires further troubleshooting by a qualified mechanic or dealer. If the ground is good, then move on to page 5 to check for Reverse polarity.
6 Technical Bulletin - Page 6 Reverse Polarity Polarity describes the direction in which electricity will flow. Current flows from the positive pole to the negative pole. Reverse Polarity then is a term that describes an electrical condition in which the positive [ + ] power wire is connected to the terminal on the receptacle intended for the ground [ - ] wire and the ground [ - ] wire is connected to the terminal on the receptacle intended for the positive [ + ] power wire. The wires are, in effect, "reversed." This condition unintentionally occurs at the factory when the single intensity turn signals are installed. So why does this not matter when we use incandescent bulbs? Well, incandescent bulbs are different from LED clusters in the respect that electricity can flow either way through the them, positive to negative or vice versa. An LED cluster will only let electricity flow one way through, Positive to negative. When we have confirmed that there is power all the way to the turn signal socket, as well as confirmed that the LED cluster lights up, then reverse polarity is usually the issue. To remedy this condition, we need to confirm it by using a test light probe, then re-wire the cluster. Follow the instructions below. 1. attach the connection clamp from the test light to a ground stud or negative battery terminal on the bike. 2. Turn the ignition on. 3. Touch the test probe to the [ + ] center contact, the test would normally light up, but since we are looking for reverse polarity, we should not have any current here. 4. Now touch the test probe to the [ - ] ground wall contact. The test light should come on. This is confirmation of reverse polarity. 5. Turn Ignition off. 6. Cut both wires on the 1156 cluster halfway between the connector base and the cluster. 7. Next, you will need 2 pieces of heat shrink tubing to cover the connections, a soldering iron and a heat gun. 8. Strip back the insulation on both ends of wires, then twist together as follows: - The connector bases end black wire will attach to the colored wire on the cluster - The connector base end colored wire will attach to the Black wire on the cluster 9. Apply solder to the connections. 10. Cover solder connections with heat shrink tubing and use the heat gun to shrink the tubing. 11. Re-install the cluster and test for function on the bike. Colored Wire Colored Wire Black Wire Black Wire = Solder Points
Looking up the front of the engine from under the radiator. (Picture taken with belt under tension.)
8. If you re replacing the AC compressor drive belt as well, it s time to loosen its belt tensioner. The AC compressor belt tensioner is very obvious under the front of the car. Loosen the 13mm bolt, then
More informationX-Type w/ non-premium sound amplifier installation instructions
X-Type w/ non-premium sound amplifier installation instructions 1. Pull radio from dash (see Radio Removal Instructions ) 2. Disconnect wiring harness from back of radio by pushing in tab on plug and pulling
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationNote: Do NOT mix LED and incandescent lamps in the same circuit!
Light Up Your Modified Car Some Hot Rod lights are hard to see. Your teardrop lights may look cool, but the 5W incandescent lamp that came with it just doesn t light up bright enough to show others you
More informationLED TROUBLESHOOTING. Controller Version L610 Rev 7M or newer (manufactured after 1/21/15)
LED TROUBLESHOOTING Controller Version L610 Rev 7M or newer (manufactured after 1/21/15) Last update 11/5/18 The purpose of this document is to help the airfield electrician troubleshoot the Lumacurve
More informationINSTALLATION CLAMP-ON FORK MOUNTED DRIVING LIGHTS 5015
CLAMP-ON 5015 PARTS INCLUDED 2 Driving Lights 2 Side Mount Clamps-43mm/49mm 1 Hardware Kit Including: 2 49mm Spacers 4 43mm Spacers 2 Pivot Dome Washers 2 3/8-16 Serrated Hex Nut 1 Wiring Kit for Driving
More informationHOW TO USE A MULTIMETER, PART 4: MEASURING CURRENT (AMPERAGE)
HOW TO USE A MULTIMETER, PART 4: MEASURING CURRENT (AMPERAGE) By: Rob Siegel First, we discussed how to use a multimeter for measuring voltage, or simply verifying that voltage is present. Last week, we
More informationINSTALLATION CONSTELLATION DRIVING LIGHTS 5009
INSTALLATION CONSTELLATION DRIVING LIGHTS 5009 PARTS INCLUDED 1 Right Driving Light with Turn Signals 1 Left Driving Light with Turn Signals 1 Installation Component Kit Including: 8 Insulated Male Spades
More informationTroubleshooting flowcharts CONTACT US 1-877-838-1399 support@rmstator.com Local & International: 819-849-7333 www.rmstator.com MELTED CONNECTORS CIRCLE OF DEATH Mispositioned connectors create irregular
More informationw w w. h d o n l i n e s h o p. d e LAYBACK LICENSE PLATE AND TURN SIGNAL RELOCATION KIT INSTALLATION GENERAL -J03892 REV Kit Number
-J0 REV. 00-0-0 LAYBACK LICENSE PLATE AND TURN SIGNAL RELOCATION KIT GENERAL Kit Number 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section
More informationUNIVERSAL GAUGE WIRE HARNESS
2650-1797-00 UNIVERSAL GAUGE WIRE HARNESS For Installing Auto Meter Electric Speedometer, Tachometer, And Short Sweep Electric Oil Pressure, Water Temperature, Fuel Level, and Volt Meter Gauges. This harness
More informationINSTALLATION CONSTELLATION DRIVING LIGHTS 5009
INSTALLATION CONSTELLATION DRIVING LIGHTS 5009 PARTS INCLUDED 1 Right Driving Light with Turn Signals 1 Left Driving Light with Turn Signals 1 Installation Component Kit Including: 8 Insulated Male Spades
More informationB29048, B29049, B29050, B29051, B29053, B
May 1, 2011 Lit. No. 48266, Rev. 05 B29048, B29049, B29050, B29051, B29053, B29400-5 HARNESS KIT 3-PORT ISOLATION MODULE LIGHT SYSTEM w/2-plug SYSTEM HARNESSES Installation Instructions Read this document
More informationTroubleshooting Guide for Okin Systems
Troubleshooting Guide for Okin Systems More lift chair manufacturers use the Okin electronics system than any other system today, mainly because they re quiet running and usually very dependable. There
More informationPage 1 of 4 Model: BTL4E-004 V2.0 Pulsar Electronic LED Turn Signal Flasher Unit Installation & Operation Instructions:
Page 1 of 4 Thank you for choosing the Bulbsthatlast4ever Model BLT4E-004 Pulsar Electronic LED Turn Signal Flasher Unit. This unit has been designed for 12-14 VDC operation with either Positive or Negative
More informationPictorial Guide to Ford Mustang Odometer Gear Replacement
Pictorial Guide to Ford Mustang Odometer Gear Replacement ***************************************************************************************************** Please read the first few steps carefully
More informationType 1 - Single filament HID kit
Instructions (V.4 01.23.2012) Type 1 - Single filament HID kit H1, H3, H7, H8, H9, H10 (9140,9145), H11, H12 (9040,9045,9055), 5202 (9009,H16), 880, 9005, 9006 These bulbs are used for low beam, high beam
More informationThough Indian s 111-cubic-inch engine delivers a
TECH by Chris Maida Andrews Indian 111 Camshafts Part I: Removing the cams from the camshaft compartment Tools Needed Red Loctite Clean rags 6mm Allen 5/64" Allen 3/32" punch External circlip pliers Needlenose
More informationLakela nd H2 Low Speed Stator Coil Installation
Lakela nd H2 Low Speed Stator Coil Installation Step 1: Place the stator assembly on a padded surface to protect the plastic signal generators, and orient it as shown in figure 1. The low speed coil is
More informationHow to Make a Solid State Instrument Voltage Regulator
Taken from the web page: http://chris66dad.tripod.com/id29.html How to Make a Solid State Instrument Voltage Regulator Note: Although this description was intended for a Ford Mustang, it also works for
More informationInstallation Manual TWM Performance Kia Forte Short Shifter
Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.
More informationINSTALLATION PROCESS: FK003D932-6 FRONT & REAR A.B.S. KIT 2017 Harley Davidson FXDL Lowrider S ABS
INSTALLATION PROCESS: FK003D932-6 FRONT & REAR A.B.S. KIT 2017 Harley Davidson FXDL Lowrider S ABS Parts List: 6 Lines 1 Splitter Block 4 A.B.S. Block Bolts (KIT A) 1 1x1/4 x20x1 Bolt 4 Caliper/Front Master
More informationTroubleshooting Guide for Limoss Systems
Troubleshooting Guide for Limoss Systems NOTE: Limoss is a manufacturer and importer of linear actuators (motors) hand controls, power supplies, and cables for motion furniture. They are quickly becoming
More informationTriumph Street Triple VSM Grip Heater Install
Triumph Street Triple VSM Grip Heater Install Introduction: With winter fast approaching and with painful memories of last winter riding with the club it was time to do something about getting some grip
More informationInstalling LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr)
Installing LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr) THINGS YOU WILL NEED: A Hypercharger (duh!) LEDs (The ones I got were from Benny Bryant at Fantasies on Wheels in Sylacauga,
More informationGETTING STARTED: SOME RECOMMENDATIONS PLEASE TRY OUR WAY FIRST!
RAINGEAR 1953/ 54 Chevrolet GETTING STARTED: SOME RECOMMENDATIONS PLEASE TRY OUR WAY FIRST! Note: This system is designed with built in adjustments to fit in your car. If, as you are installing it, you
More informationMGB Alternator Conversion Installation Instructions For MGA & 1962 to 1967 MGB
MGB Alternator Conversion Installation Instructions For MGA & 1962 to 1967 MGB PART# 130-078, 130-088, 130-098 440 Rutherford St. Goleta, CA 93117 1-800-642-8295 FAX 805-692-2525 www.mossmotors.com Scan
More informationWolverine Turn Signal / Horn Kit 2102
All years Yamaha Wolverine STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR ALL YEAR AND MODELS YAMAHA WOLVERINE. IF YOUR MACHINE IS NOT ONE OF THESE MODELS DO NOT PROCEED. Contact Ryco Motorsports or your
More informationTONY S TECH REPORT. Basic Training
TONY S TECH REPORT (Great Articles! Collect Them All! Trade them with your friends!) Basic Training OK YOU MAGGOTS!! Line up, shut up, and listen good. I don t want any of you gettin killed because you
More informationBULLET & MINI-BULLET TACHOMETERS INSTALLATION GUIDE - Please see appropriate section for your specific application
Revision: 17.7-04/12/2012 Install Time: 30 to 90 Minutes BA-757x-xx Page: 1 Go slowly and follow instructions carefully. The installation is very easy if the wire color destinations are followed. INCLUDED
More information29048, 29049, 29050, 29051, 29052, 29053, 29054,
April 15, 2014 Lit. No. 29225, Rev. 11 29048, 29049, 29050, 29051, 29052, 29053, 29054, 29400 5 HARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM w/2 PLUG SYSTEM HARNESSES Installation Instructions Read
More informationShotgun Single Barrel HPFP install guide
Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More information2479 Hella oem turn signal flasher relay short diagnosis and repair
2479 Hella oem turn signal flasher relay short diagnosis and repair Identifying the Hella relay in your headlight bucket: Early Hella 2479 current Hella 3425 The /6s were all supplied with the early Hella
More informationHID INSTALLATION ON RST1000 Futura
HID INSTALLATION ON RST1000 Futura Disclaimer: This is a full description of what I have done to my motorcycle. I am in no way suggesting you do as I have done by following these instructions. I have not
More informationOwner s Manual Electronic Harness Controller P/N ASM4250
Owner s Manual Electronic Harness Controller P/N ASM4250 Thunder Heart Performance Corporation MANUAL P/N EI4250 120 Industrial Drive Revision 6/3/04 White House, TN 37188 www.thunder-heart.com TABLE
More informationWe have had a request for instructions on how to replace the 50 AMP CR relay in the A/C electrical box with the upgraded 70 AMP relay.
We have had a request for instructions on how to replace the 50 AMP CR relay in the A/C electrical box with the upgraded 70 AMP relay. This Carolina Thomas Bus Buzz provides instructions as to how we go
More information1. Get fork mounted in stand. You can leave it in the bike, but you must remove the wheel and front brake.
Tools Needed: Bike stand Lint free shop Towels 1.5mm Allen Key Pick Set Grease (We recommend Slick Honey) Oil Measuring Cup (with cc Scale) Small Metal Drift Shop Vise Oil Bucket 13mm Deep Socket (6 point)
More informationV-Bullet Installation Instructions
V-Bullet Installation Instructions Thank you for purchasing our high quality V-Bullet disc LED kit. Your business is greatly appreciated. Please follow the instructions below. Failure to follow the procedure
More information29048, 29049, 29050, 29051, 29052, 20953, 29054,
July 15, 2008 Lit. No. 29225, Rev. 06 29048, 29049, 29050, 29051, 29052, 20953, 29054, 29400-2 HARNESS KIT 3-PORT ISOLATION MODULE LIGHT SYSTEM w/2-plug SYSTEM HARNESSES Installation Instructions Read
More informationInstallation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer
Page 1 Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift
More informationMCL-3000 SERIES AIR PRESSURE PART# MCL-3K-A
MCL-3000 SERIES AIR PRESSURE PART# MCL-3K-A Thank you for purchasing the Dakota Digital MCL-3K-A gauge for your Harley Davidson Touring bike. This gauge is designed to be a direct, plug in replacement
More informationInstallation of Raxiom Switchback Turn Signal Conversion Kit w/resistors
Installation of Raxiom Switchback Turn Signal Conversion Kit w/resistors Overview: Below are the steps involved in the installation of the Raxiom Switchback Turn Signal LED lights in the 1987 1993 Ford
More informationINSTRUCTIONS. w w w. h d o n l i n e s h o p. d e ENGINE GUARD-MOUNTED FOG LAMP KIT 1WARNING -J02798 REV Installation.
INSTRUCTIONS -J0798 REV. 9-4-00 Kit Number 689-98B General ENGINE GUARD-MOUNTED FOG LAMP KIT Installation This kit fits all models equipped with Harley-Davidson -/4 in. ( mm) diameter front engine guards,
More informationSAISBM V36W Installation Instructions
The Original Secondary Air Injection System Bypass Kit SAISBM V36W Installation Instructions All Applicable Toyota/Lexus Vehicles Introduction: The Secondary Air Injection System (SAIS) bypass module is
More informationTools & Parts I Used. Here's everything that comes with the kit.
Ford Super Duty Power Tailgate Lock Install 2004 F250 4x4 XLT Sport Crew Cab Back to 2004 F250 Main Page This page describes the steps to install the Pop & Lock PL8250 power tailgate lock kit. This kit
More informationInstallation Procedures
Installation Procedures Ziza Interior Lighting Package Installation for BMW E46 Sedan This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe,
More informationATTENTION. Custom Dynamics UTV Turn Signal Kit Installation Instructions
Custom Dynamics UTV Kit Installation Instructions We thank you for purchasing the Custom Dynamics UTV LED Kit. Our products utilize the latest technology and high quality components to ensure you the most
More informationw w w. h d o n l i n e s h o p. d e CHROME FAN KIT GENERAL INSTALLATION -J04347 REV Kit Number Models Kit Contents
-J0447 REV. 008-08-05 CHROME FAN KIT GENERAL Kit Number 996-08 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationINSTALLATION ZOMBIE L.E.D. FUEL & BATTERY GAUGE. THANK YOU FOR CHOOSING KϋRYAKYN!
THANK YOU FOR CHOOSING KϋRYAKYN! PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND PROPERTY DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS, AND NOTICES REGARDING THE, USE,
More informationfeature 10 the bimmer pub
feature 10 the bimmer pub BMW E90 Steering Angle Sensor Diagnosis A pattern failure may indeed point you to a bad component, but when the part is expensive you want to be very sure it s the culprit before
More information2016 HONDA 1000 Pioneer PN 3102 Turn signal / horn kit rev nc
2016 Honda 1000 Pioneer STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR 2016 HONDA 1000 PIONEER IF YOUR MACHINE IS NOT THIS MODEL DO NOT PROCEED. THIS KIT DOES NOT WORK ON THE PIONEER 500 nor 700 S. Contact
More informationInstalling the Dan-Marc and Pingel setup.
Installing the Dan-Marc and Pingel setup. This is an alternative to the OEM vacuum petcock. It's the setup I use and feel more comfortable with it. Many still like the OEM vacuum petcock and they can continue
More informationThunder Power Tarp Kit Operation. Dual Arm Curb Side Stowing Single Arm Curb Side Stowing Flex Arm Curb Side Stowing.
Thunder Power Tarp Kit Operation Dual Arm Curb Side Stowing Single Arm Curb Side Stowing Flex Arm Curb Side Stowing 011-52475 Rev - 2 P a g e USE THE PROCEDURES BELOW TO OPERATE THE TARP SYSTEM Powering
More informationMustang Short Throw Sport Shifter (All 83 - Early 01 & V6 T-5/T-45 Transmission) - Installation Instructions
Mustang Short Throw Sport Shifter (All 83 - Early 01 & 01-04 V6 T-5/T-45 Transmission) - Installation Instructions The below installation instructions work for the following products: Mustang Short Throw
More informationService Procedure # CDV-101
TRW Automotive Commercial Steering Systems Service Procedure # CDV-101 TRW ColumnDrive Troubleshooting Guide March, 2007 NOTE Take appropriate safety measures before beginning this procedure. This TRW
More informationComponents included in your kit:
Page 1 Components included in your kit: The LED flasher module will replace your existing flasher module. The left and right taillight modules will replace your existing All of the equipment illustrated
More informationElectrical Circuits: Automatic Book Light
Henry Lin Hani Mehrpouyan Electrical Circuits: Automatic Book Light Note: Do not look directly at LED with unshielded eyes or damage to retina may occur. Introduction: In this lab you will construct a
More informationFord Super Duty Dash Lighting LED Upgrade F250 4x4 XLT Sport Crew Cab
Page 1 of 32 Ford Super Duty Dash Lighting LED Upgrade 2004 F250 4x4 XLT Sport Crew Cab Back to 2004 F250 Main Page Click Here for a PDF version of this article ** Updated 12/15/09 ** New version of the
More informationJRC ENGINEERING INC 3110 Indian Ave Suite E Perris, California
JRC ENGINEERING INC 3110 Indian Ave Suite E Perris, California 92571 800-634-3250 Thank you for choosing our 750 conversion for your Triumph 650. Careful assembly and running in will greatly extend the
More informationINSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax)
INSTALLATION MANUAL August 7 th 2018 43 /48 /50 2011 and Older Timpte STD/Split 36 Style Hopper Trailers with Roller Bearing Doors Kit #101533 for 96w & Kit #101534 for 102w Thunderstone Manufacturing
More informationContacts The moveable contact, which is the one affected by the armature is sometimes referred to as the hinge contact.
Relays & Wiring 101 Basically, a relay is an electrically operated, remotely controlled switch. A simple electromagnetic relay is an adaptation of an electromagnet. It consists of a coil of wire surrounding
More informationIgnition Installation Troubleshooting Tips/Frequently-Asked Questions
Ignition Installation Troubleshooting Tips/Frequently-Asked Questions Warning: Reversing the red and black ignition wires will destroy the ignition module and void the warranty. The Hot-Spark module s
More informationINSTALLATION TURN SIGNAL MIRRORS 1432
1432 PARTS INCLUDED 1 Left Side Turn Signal Mirror Assembly with Convex Glass 1 Right Side Turn Signal Mirror Assembly with Convex Glass 1 Hardware Kit, Including: 2 5/16-18 X 1-1/2 Socket Head Cap Screws
More informationALTERNATOR - BOSCH 35/75-AMP & 40/90-AMP
ALTERNATOR - BOSCH 35/75-AMP & 40/90-AMP 1988 Chrysler LeBaron Convert/Coupe 1988 ALTERNATORS & REGULATORS Chrysler Motors - Bosch 35/75 & 40/90 Amp Alternator All Models DESCRIPTION The charging system
More informationDexter Never-Adjust Brake Install
Dexter Never-Adjust Brake Install Arctic Fox 2007 29-5T Warning: This involves lifting your trailer, working under and around it. If you do not have the correct equipment and knowledge for this, please
More informationInstallation Procedures
Installation Procedures Ziza Interior Lighting Package Installation for BMW E38 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable
More informationINSTALLATION GUIDE CRF150R Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE CRF150R 191-810 Manual Revision: 032508 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714 208-426-0659
More informationRetrofitting an R Instrument Cluster
Retrofitting an R Instrument Cluster This is a step-by-step tutorial for those wishing to incorporate the unique look of the R instrument gauges to their current modules. Before starting, be certain that
More informationCORKSPORT CX-3 Interior LED Light Kit
I N S T A L L A T I O N I N S T R U C T I O N S CORKSPORT CX-3 Interior LED Light Kit 2016+ Mazda CX-3 PART #: CX3-9-011-10 Need Help With Your Installation? Call (360) 260-CORK PAGE 1 CORKSPORT CX-3 Interior
More informationZiza Interior Lighting Package Installation Procedures
Ziza Interior Lighting Package Installation Procedures This tutorial is provided as a courtesy by ECS Tuning. Part Number for Audi B5 A4 (sedan or Avant) (1996-2001) Audi B5 S4 (2000-2002) Proper service
More informationINSTALLATION INSTRUCTIONS. Applications: 2005-Current Ford Excursion 2005-Current Ford F250, F-350, F-450 & F-550 Super Duty Pickups.
30453 INSTALLATION INSTRUCTIONS Tools Required: Drill with 1/8 Bit 1/4 Nut Driver Phillips Screwdriver Probe Style Test Light Applications: 2005-Current Ford Excursion 2005-Current Ford F250, F-350, F-450
More informationMazda North American Operations Irvine, CA
Service Bulletin Mazda North American Operations Irvine, CA 92618-2922 Subject: STARTER MOTOR WILL NOT CRANK AND ENGINE DOES NOT START (INTER- MITTENTLY) Bulletin No: 01-037/08 2004-2008 MAZDA3 - STARTER
More informationINSTALLATION INSTRUCTIONS
THANK YOU FOR CHOOSING KURYAKYN! Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation,
More informationQuick Install Lift AL065 Installation Guide & Owners Manual
Quick Install Lift AL065 Installation Guide & Owners Manual Congratulations on your new lift purchase. The Quick Install Lift line is one of the easiest and most trouble free ways to transport your scooter
More informationAFT mid drive kit Trouble shooting guide For 24v to 48V Kelly Controller KBS 48101L-L 100 A peak
Date: 2016-13-1 AFT mid drive kit trouble shooting guide Rev 1.7 Page 1 of 17 AFT mid drive kit Trouble shooting guide For 24v to 48V Kelly Controller KBS 48101L-L 100 Table of Contents 1. Safety... 2
More informationUser s Manual. Automatic Switch-Mode Battery Charger
User s Manual Automatic Switch-Mode Battery Charger IMPORTANT Read, understand, and follow these safety rules and operating instructions before using this battery charger. Only authorized and trained service
More informationInstallation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)
Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well
More informationXR Conveyor Maintenance Guide
XR Conveyor Maintenance Guide EN-0035 Rev. A XR Conveyor Maintenance Guide www.qdraw.com Table of Contents 05/20/2009 Overview Page 3 XR Conveyor Assembly Page 4 General Information Exploded View of an
More informationINSTALLATION. DRIVING LIGHTS for FLHT/FLHX/FLHR 5005
DRIVING LIGHTS for FLHT/FLHX/FLHR 5005 PARTS INCLUDED 1 Right Driving Light Assembly 1 Left Driving Light Assembly 1 Right Driving Light Bracket 1 Left Driving Light Bracket 4 Driving Light Bracket Plugs
More informationSOME BASICS OF TROUBLESHOOTING
SOME BASICS OF TROUBLESHOOTING DICK RANDALL I decided to pull these ideas together because I have spent plenty of hobby time figuring out things that did not work or that needed repair. This process and
More informationBench Test for 2-Wire Window Lift Motors
Bench Test for 2-Wire Window Lift Motors All vehicles with electric windows (2-wire motor). Window lift motor replacement only operates in one direction. Possible faulty wiring or control switch. Most
More informationTurn Signal Kit Installation Instructions for Model A Fords & Other Antique Vehicles
Turn Signal Kit Installation Instructions for Model A Fords & Other Antique Vehicles Lifetime Technical Support support@logolites.com 770-476-7322 www.logolites.com Manual 100-0005N Thank you for purchasing
More informationCOMBINATION SPEEDOMETER/TACHOMETER GAUGE KIT J
COMBINATION SPEEDOMETER/TACHOMETER GAUGE KIT J05306 2015-04-24 GENERAL Figure 1. Title 49, United States Code GENERAL (Continued) Table 1. Speedometer Features Available MODELS FEATURES GEAR INDICATOR
More informationWiring checks below assume the vehicle is in reverse, secured so it won't roll, and key is on so backup lights are illuminated:
Reverse Lockout Troubleshooting The way that the backup solenoid works is: When the backup lights are lit on your tow vehicle, 12 volt power should come down the blue wire through the trailer connector
More informationInstallation Manual TWM Performance Short Shifter Subaru STi 2008+
- 1 - Installation Manual TWM Performance Short Shifter Subaru STi 2008+ Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationRAINGEAR 1953/ 54 Chevrolet
RAINGEAR 1953/ 54 Chevrolet GETTING STARTED: SOME RECOMMENDATIONS PLEASE TRY OUR WAY FIRST! Note: This system is designed with built in adjustments to fit in your car. If, as you are installing it, you
More information2010 BMW S1000RR TracStar HeliBars TS mm taller (1.7 ) ~ 20mm Rear Offset (.8 ) ~ Stock Width (25 ¼ )
WARNING: IMPROPER INSTALLATION COULD RESULT IN SERIOUS INJURY OR DEATH. HAVE A QUALIFIED MECHANIC INSTALL YOUR HELIBARS. Right Side To protect your motorcycle during installation place clean shop rags
More informationComponents included in your kit:
Page 1 Components included in your kit: All of the equipment illustrated in this manual was proudly manufactured in the USA by Mustang Project a SafeCode Inc. enterprise. For accessories and spare parts
More informationIn the first two parts of
Actuator 1: Solenoids Solenoids are one of the easiest components to check electrically. In simplest terms, solenoids are electromagnets: They receive power and ground, which energizes the windings and
More informationHow to Keep your Treadmill Running
How to Keep your Treadmill Running Buying a treadmill is hard enough. Choosing the best out of many treadmills in the market is nigh impossible. But once you ve got the treadmill you ve always wanted,
More informationwww.odometergears.com Mercedes-Benz Mechanical Odometer Repair This how to can be used for all mechanical repairs as the only difference will be the removal of the instrument cluster. http://www.dieselgiant.com/repairyourodometer.htm
More informationR O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP
R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer
More informationHEATED HAND GRIP KIT
-J0596 REV. 00-- HEATED HAND GRIP KIT GENERAL Kit Number 56000 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationTroubleshooting Guide for Dewert Systems
Troubleshooting Guide for Dewert Systems Dewert electronics aren t as common as Okin systems as they re mainly used by one manufacturer (Pride). However, Pride is the largest lift chair manufacturer in
More informationFREIGHT TRAIN HEADLAMP NACELLE KITS
-J09 0-08-8 FREIGHT TRAIN HEADLAMP NACELLE KITS GENERAL Kit Numbers 6000, 600 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of wwwharley-davidsoncom
More informationTHREE PHASE RECHARGING SYSTEM DIAGNOSIS
THREE PHASE RECHARGING SYSTEM DIAGNOSIS INDEX 1. Foreword 2. Battery Voltage 3. Recharging System Connections 4. Stator Three Phase Continuity 5. Alternator Phase Insulation 6. Checking Absorption with
More informationSelf-Adjust Clutch Installation Guide
Self-Adjust Clutch Installation Guide 0 STOP! READ CAREFULLY BEFORE INSTALLING CLUTCH This clutch must be installed by a qualified installer. Improper installation or failure to replace or resurface the
More informationECT Display Driver Installation for AP2 Module
ECT Display Driver Installation for AP2 Module Overview The ECT Display Driver is a small module with a removable wire harness that mounts behind the driver's foot well cover. All wiring connections are
More informationClutch Installation Guide
Clutch Installation Guide 0 STOP! READ CAREFULLY BEFORE INSTALLING CLUTCH This clutch must be installed by a qualified installer. Improper installation or failure to replace or resurface the flywheel,
More informationPHOENIX Amp Brushless Sensorless Speed Control. 1.0 Features of the Phoenix-25 : 2.3 Connecting the Motor. 2.4 Reversing Rotation
1.0 Features of the Phoenix-25 : Extremely Low Resistance (.013 ohms) High rate (7 KHz) switching (PWM) Up to 25 Amps continuous current with proper air flow, 35 amps surge Five to eight cells with four
More information