5B HIGH FLOW CATTED DOWNPIPES N54 135i/335i
|
|
- Bonnie Lindsey
- 5 years ago
- Views:
Transcription
1 5B HIGH FLOW CATTED DOWNPIPES N54 135i/335i Installation Instructions Front Downpipe Rear Downpipe Congratulations on your purchase of the COBB High Flow Catted Downpipes for your N54 BMW 135i/335i! The following instructions will assist you through the installation process. Please read through all of the instructions first BEFORE beginning the install and familiarize yourself with the steps and tools needed. If you feel that you cannot properly perform this installation, we HIGHLY recommend you take the vehicle to a qualified and experienced automotive technician.
2 Parts List (1) Front Downpipe (1) Rear Downpipe (2) Gaskets (4) M8 x 1.25 x 30 Bolts (4) M8 x 1.25 Hex Nuts Tools Needed Ratchet Sockets: 8mm, 12mm, 13mm, 14mm Socket Swivel Socket Extensions Box Wrenches: 16mm, 22mm or 7/8 Large Flathead Screw Driver Small Flathead Screw Driver TORX Sockets: T25, E10, E12, E18 Check Engine Light/Trouble Codes Reference 0041 O2 Signals Swapped 2C6A O2 Signals Swapped 2C7F Rear O2 Bank 2 Too Rich 2C31 Front O2 Bank 1 2C32 Front O2 Bank 2 2C6B Rear O2 System Check 2C6C Rear O2 Bank 2 System Check U0428 Invalid Data Received from Steering Angle Sensor Module Copyright 2012 COBB Tuning Products LLC. All Rights Reserved 1
3 Removal of Stock Downpipes: 1. Start off by getting the vehicle up on a lift or placing jack stands under the front of the vehicle to get it up in the air and give you some room to work. Make sure the emergency brake is set firmly and you ve blocked the rear wheels if you re using jack stands. 2. Loosen / remove the stock exhaust. The downpipe installation can be accomplished by just loosening the stock exhaust, but it is much easier if the exhaust is removed. If you have an aftermarket exhaust, just the front portion of the exhaust needs to be removed. The exhaust bracket can be removed with an E10 TORX socket and a 13mm wrench/socket. You will also need a 12mm socket to remove the 4 x DP flange bolts. 3. Next remove the front underbody panel with an 8mm socket. Copyright 2012 COBB Tuning Products LLC. All Rights Reserved 2
4 4. Unbolt the steering rack using a 16mm wrench and an E12 TORX socket. The 16mm nut is hidden on the top side of the steering rack. Next lower and slide the steering rack over to the driver side to allow for more space to access the downpipes. 5. Remove the steering rack heat shield using the T25 TORX socket. There are three screws that need to be removed. Copyright 2012 COBB Tuning Products LLC. All Rights Reserved 3
5 6. Before you remove the front oxygen sensors, it is recommended that you mark them so that you remember which goes in the front or rear downpipe. Once they are market you can remove the front oxygen sensors. First remove the front downpipe oxygen sensor with the 22mm or 7/8 wrench. Next remove the rear oxygen sensor. CAUTION: Handle the oxygen sensors with care. They can be damaged easily and will cause error codes. Remove Second O2 Sensor Remove First O2 Sensor 7. Using the 12mm socket, remove the two bolts that hold the stock downpipes to downpipe bracket. Copyright 2012 COBB Tuning Products LLC. All Rights Reserved 4
6 8. Unplug the rear oxygen sensors and loosen the wires from the clips. Using one or two small flat head screw drivers will help you release the tabs that lock the sensors into their connectors. Front DP O2 sensor wire is Black Rear DP O2 sensor wire is Gray 9. Loosen the v-band clamps on both downpipes using the 13mm socket. Use a screw driver if necessary to break the v-band clamps loose after the bolts have been removed. Copyright 2012 COBB Tuning Products LLC. All Rights Reserved 5
7 10. Remove the front downpipe first by snaking it past the subframe. 11. With the front downpipe removed, you will now have enough space to remove the rear downpipe. 12. Remove the downpipe bracket with the E18 TORX socket (14mm socket works as well). The transmission bolts are aluminum so be careful not to over torque them when putting the bolts back in. Copyright 2012 COBB Tuning Products LLC. All Rights Reserved 6
8 Copyright 2012 COBB Tuning Products LLC. All Rights Reserved 7
9 13. Remove the rear oxygen sensors with a 22mm or 7/8 wrench. CAUTION: Handle the oxygen sensors with care. They can be damaged easily and will cause error codes. Copyright 2012 COBB Tuning Products LLC. All Rights Reserved 8
10 Installation of COBB N54 High Flow Catted Downpipes: 1. Install the rear oxygen sensors into the COBB Downpipes using the 22mm or 7/8 wrench. CAUTION: Handle oxygen sensors with care. They can be damaged easily and will cause error codes. The oxygen sensor with a BLACK wire is for the FRONT DOWNPIPE and the oxygen sensor with a GRAY wire is for the REAR DOWNPIPE. Switching the front and rear oxygen sensors will cause error codes. See list for possible codes above. 2. Install the Rear Downpipe by snaking it in between the subframe and the chassis. Secure the downpipe loosely into v-band clamp using the 13mm socket and bolt but do not fully tighten. 3. Install the Front Downpipe next. Again snake the downpipe between the subframe, rear downpipe and chassis to install. Secure it loosely into the v-band clamp as well. 4. Plug in the rear oxygen sensor cables. Make sure to double check the oxygen sensor wires such that they are installed into the correct downpipe. The black O2 sensor goes to the front downpipe and the gray O2 sensor goes to the rear downpipe. Copyright 2012 COBB Tuning Products LLC. All Rights Reserved 9
11 5. Install the 4 x bolts and 2 x gaskets. The N54 is sensitive to exhaust leaks here and may trigger catalytic converter codes if there are leaks. Use the supplied gaskets because the OEM gaskets tend to break down over time and may leak. 6. Install the exhaust back onto the DP flanges and tighten with the supplied 4 x serrated flange bolts and a 12mm socket. 7. Once the exhaust is tightened, you can tighten the v-band clamps on the turbos with a 13mm socket. Copyright 2012 COBB Tuning Products LLC. All Rights Reserved 10
12 8. Install the rear downpipe front, oxygen sensor first using a 22mm or 7/8 wrench. Next install the front downpipe, front oxygen sensor. You won t be able to torque down the rear oxygen sensor when the front oxygen sensor is in place. CAUTION: Handle the oxygen sensors with care. They can be damaged easily and will cause error codes. The oxygen sensor with a BLACK wire is for the FRONT DOWNPIPE and the oxygen sensor with a GRAY wire is for the REAR DOWNPIPE. Switching the front and rear oxygen sensors will cause error codes. See list for possible codes above. Install and tighten front downpipe O2 sensor second. Install and tighten rear downpipe O2 sensor first. 9. Reinstall the steering rack heat shield with T25 TORX socket. 10. Move the steering rack back into place and bolt it back onto the subframe using a 16mm wrench and E12 TORX socket. 11. Finally, reinstall the underbody panel using an 8mm socket. 12. Download and/or Install the appropriate Stage2 or Stage2+ FMIC map using your COBB Accessport. 13. Congratulations! You have completed the installation of the COBB Downpipes for your BMW. Go out and enjoy! Copyright 2012 COBB Tuning Products LLC. All Rights Reserved 11
Turboback Exhaust
501301 Turboback Exhaust 2014+ Ford Fiesta ST 501200 High Flow Catted Downpipe Page 2 501100 Catback Exhaust System Page 10 501200 High Flow Catted Downpipe 2014+ Ford Fiesta ST Congratulations on your
More informationCOBB Catback Exhaust
591100 COBB Catback Exhaust 2013 Ford Focus ST Congratulations on your purchase of the COBB Catback Exhaust for your 2013 Ford Focus ST. The following instructions will assist you through your installation
More information7B1210 COBB BMW N54 Charge Pipe
7B1210 COBB BMW N54 Charge Pipe Installation Instructions Congratulations on your purchase of the COBB BMW N54 Charge Pipe for your BMW. The following instructions will assist you through your installation
More informationCOBB Tuning Catback Exhaust System MAZDASPEED3
572101 COBB Tuning Catback Exhaust System 2010+ MAZDASPEED3 Congratulations on your purchase of the COBB Tuning SS Catback Exhaust System for your 2010+ MAZDASPEED3. The following instructions will assist
More informationHARD PIPE KIT
701550 HARD PIPE KIT 2014 Ford Fiesta ST Congratulations on your purchase of the COBB Hard Pipe Kit for your 2014+ Ford Fiesta ST. The following instructions will assist you through your installation process.
More information9F1760/9F1761 COBB Sport Springs Ford Focus ST
9F1760/9F1761 COBB Sport Springs 2013+ Ford Focus ST Installation Instructions Congratulations on your purchase of the COBB Sport Springs for your 2013+ Ford Focus ST. These instructions should only be
More informationFocus RS Catback
593100 - Focus RS Catback 593100 Focus RS Catback Ford Focus RS 2016-18 Congratulations on your purchase of the COBB Tuning Focus RS Catback Exhaust! The following instructions will assist you through
More informationLightweight Tubular Sway Bar Kit Subaru WRX / STi / 09+ FXT
915250 Lightweight Tubular Sway Bar Kit 2008+ Subaru WRX / STi / 09+ FXT Installation Instructions Congratulations on your purchase of the COBB Lightweight Tubular Sway Bar Kit for your Subaru WRX, STi
More informationCOBB Tuning MAZDASPEED6 SF Intake System. Install Instructions
781500 COBB Tuning MAZDASPEED6 SF Intake System Install Instructions Congratulations on your purchase of the COBB Tuning SF Intake System. The following instructions will assist you through your installation
More informationCOBB 3 SF INTAKE SYSTEM
COBB 3 SF INTAKE SYSTEM 2015 Mustang Ecoboost Congratulations on your purchase of the COBB 3 SF Intake System for your 2015 Mustang Ecoboost. The following instructions will assist you through your installation
More informationCOBB SPORT SPRINGS
915760 - COBB SPORT SPRINGS 2008-2013 Subaru WRX/STi Congratulations on your purchase of the COBB Sport Springs for your 2008-2013 Subaru WRX/STi. The following instructions will assist you through your
More informationFocus ST Carbon Fiber Intake
791400 - Focus ST Carbon Fiber Intake 791400 COBB Focus ST Carbon Fiber Intake Congratulations on your purchase of the COBB Tuning Carbon Fiber Intake System! The following instructions will assist you
More informationCOBB SPORT SPRINGS
913760 - COBB SPORT SPRINGS 2004-2007 Subaru WRX/STi Congratulations on your purchase of the COBB Sport Springs for your 2004-2007 Subaru WRX/STi. The following instructions will assist you through your
More informationINSTALLATION INSTRUCTIONS Unitronic Turbo-Back Exhaust System for MK7 GTI UH026-EXA
Unitronic Turbo-Back Exhaust System for MK7 GTI Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included
More informationCOBB 3-Port Electronic Boost Control Solenoid
COBB 3-Port Electronic Boost Control Solenoid MazdaSpeed3/Mazdaspeed6 Congratulations on your purchase of the COBB Tuning 3-Port Electronic Boost Control Solenoid. The following instructions will assist
More informationINSTALLATION INSTRUCTIONS Unitronic Downpipe for AWD 2.0 TSI Gen3 MQB UH027-EXA
Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included components, tools required, and procedures
More informationSaab 9-3 Krona Downpipe Installation Instructions. What's Included:
www.kronaperformance.com 2003-2010 Saab 9-3 Krona Downpipe Installation Instructions What's Included: (1) 3 stainless downpipe (with or without catalyst) (1) 3-2.5 stainless downpipe adapter pipe (1) Turbo
More informationINSTALLATION INSTRUCTIONS Unitronic 3 Turbo-Back Exhaust System for Golf R UH021-EXA
Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included components, tools required, and procedures
More informationCOBB Fuel Pressure Regulator Kit
315100 COBB Fuel Pressure Regulator Kit 2008+ Subaru STI Congratulations on your purchase of the COBB Tuning Fuel Pressure Regulator Kit for your 2008+ Subaru STI. The following instructions will assist
More informationCOBB SF SHORT RAM INTAKE SYSTEM MazdaSpeed3
COBB SF SHORT RAM INTAKE SYSTEM MazdaSpeed3 Congratulations on your purchase of the COBB Tuning SF Intake System. The following instructions should assist you through your installation process. Please
More informationSubaru WRX MRT Turbo Back Exhaust System
2015-16 Subaru WRX MRT Turbo Back Exhaust System Part No. 98P113 STOP Verify that all of the following components are included in kit before beginning installation: Part #1 J-Pipe / Downpipe Part #2 Mid-Pipe
More information7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions
7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following
More informationINSTALLATION INSTRUCTIONS Unitronic 3 Turbo-Back Exhaust System for MK5 Jetta /GLI UH020-EXA
Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included components, tools required, and procedures
More informationInstallation Instructions
Installation Instructions Transverse K04 Tools Required Jack and jack stands Drain pan for coolant and oil 3" and 6" extensions Channel locks 7mm, 8mm, 10mm, 11mm, 12mm, 13mm, and 16mm sockets Oxygen sensor
More informationIE MK5 & MK6 Downpipe Install Guide IEEXCC5
IE MK5 & MK6 Downpipe Install Guide IEEXCC5 Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation of IE s 3 Downpipe System for VW
More informationInstall Guide B9 Audi A4/A5 2.0T Racing Catalyst
Cast Stainless Steel Racing Catalyst, B9 Audi A4/A5 & Allroad 2.0 TFSI Installation Spiciness Rating (Spicy) Installation of your 034Motorsport Cast Racing Catalyst is a complex process. We recommend professional
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationBMW F8x M3 & M4 Valvetronic Exhaust System
BMW F8x M3 & M4 Valvetronic Exhaust System SKU: FS.BMW.F8X.VLVP Required Tools Hydraulic Lift or Floor Jack & Stands Metric Socket Set w/ Ratchet & Extensions Metric Open-End Wrench Set Inverted Torx Bits
More informationVW & Audi TDI CR140 ECO KIT Installation Guide
VW & Audi TDI CR140 ECO KIT Installation Guide This guide is to help you install your new Rawtek DPF, EGR & Adblue Delete Exhaust ECO Kit on your (2009-2014) VW / Audi with 2.0l CR140 Diesel Engine. Note:
More information3 Turbo Downpipe Installation Audi A3 / Volkswagen GTI / Volkswagen Jetta 2.0L FSI/TSI Turbo CD100013
Please take time to read and understand these installation instructions. APR recommends that installation of this system be performed by a qualified service center or professional muffler installer who
More informationCOBB 3-Port Electronic Boost Control Solenoid
COBB 3-Port Electronic Boost Control Solenoid Mitsubishi Evolution X / Ralliart Congratulations on your purchase of the COBB Tuning 3-Port Electronic Boost Control Solenoid. The following instructions
More informationExhaust System Installation Turbo Downpipe Audi MKII TT-RS 2.5T CD100028
Please take the time to read and understand installation instructions. APR recommends that installation of this system be performed by a qualified service center or professional muffler installer who has
More informationTENF8046MCD F8X M3/M4 TEST PIPES (REMOVES SECONDARY CATS) **NOT FOR USE ON ROAD VEHICLES / FOR OFF-ROAD AND RACING USE ONLY**
Turner Motorsport LLC / 1-800-280-6966 / www.turnermotorsport.com DI/DBM 3/21/16 TENF8046MCD F8X M3/M4 TEST PIPES (REMOVES SECONDARY CATS) **NOT FOR USE ON ROAD VEHICLES / FOR OFF-ROAD AND RACING USE ONLY**
More informationInstallation Instructions Short Throw Shifter
Installation Instructions Short Throw Shifter 2000-2001 Audi TT 1.8L Turbo Including FWD and AWD (Quattro) Part Number 45146 2003,2001 by B&M Racing and Performance Products LLC This B&M Short Throw Shifter
More informationARK Exhaust System GRiP Cat-Back with optional Down Pipe/Test Pipe
ARK Exhaust System GRiP Cat-Back with optional Down Pipe/Test Pipe (SM0702-102G, 202G, 302G; DP0702-0020) for Hyundai Genesis Coupe (2.0L I4 Turbo Theta TCi) Congratulations on purchasing an ARK Performance
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Performance We ask that you take a few moments to
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED TO ACTIVATE YOUR WARRANTY GO TO: CORSAPERFORMANCE.COM/WARRANTY STOP
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Performance We ask that you take a few moments to
More informationInstall Guide MQB 1.8T/2.0T Cast Downpipe
Cast Stainless Steel Performance Downpipe, 8V Audi A3/S3 & MkVII Volkswagen Golf/GTI/R Installation Spiciness Rating (Spicy) Installation of your 034Motorsport Cast Downpipe is a complex process. We recommend
More informationPerformance Oil Cooler Kit for (C6) Chevrolet Corvette
Performance Oil Cooler Kit for 2005-2013 (C6) Chevrolet Corvette Part No. EC6-600 Made in USA Important: Read these instructions in their entirety prior to installation. Copyright 2008-2018 Improved Racing
More informationIE B9 A4/A5 Cold Air Intake Install Guide
IE B9 A4/A5 Cold Air Intake Install Guide Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation of IE s Cold Air Intake Kit for Audi
More informationThank you for purchasing the AWE SwitchPath Exhaust System for the Audi B9 S5 Sportback.
Thank you for purchasing the AWE SwitchPath Exhaust System for the 2017+ Audi B9 S5 Sportback. Let s go! Switchpath Exhaust Parts: 1 Driver downpipe upper section (part A10) 1 Driver downpipe lower section
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust STOP Please take time to read and understand
More informationTuned Length Headers. Special Tools Required: Install Time: Difficulty: Follow these instructions carefully to ensure correct fitment and operation.
Special Tools Required: welder / saws all Install Time: Approximately 4 Hours Difficulty: 4 out of 5 Follow these instructions carefully to ensure correct fitment and operation. STEP 1 Disconnect the negative
More informationActive Autowerke Exhaust Down Pipe Set Installation Instructions for the BMW V8 models with Twin Turbos (Pre 04/2011)
Active Autowerke Exhaust Down Pipe Set Installation Instructions for the BMW V8 models with Twin Turbos (Pre 04/2011) E70 X5 5.0i, M E71 X6 5.0i, M F01 750i, ALPINA B7 F07 550i F10 550i F12 650i Thank
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationCAT-BACK EXHAUST FORD FIESTA ST PARTS LIST AND INSTALLATION GUIDE WARNING PARTS INCLUDED INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC STAINLESS STEEL RESONATED MIDPIPE W/ 2-BOLT FLANGE 1PC STAINLESS STEEL MIDPIPE-TO-REAR MUFFLER SECTION 1PC STAINLESS STEEL REAR MUFFLER SECTION 1PC 3" DUAL OFFSET TIPS
More informationCOBB Tuning Ford Carbon Fiber Air Scoop Focus ST COBB Ford Carbon Fiber Air Scoop Focus ST
791450 - COBB Tuning Ford Carbon Fiber Air Scoop Focus ST 2013-2017 791450 COBB Ford Carbon Fiber Air Scoop 2013-2017 Focus ST Congratulations on your purchase of the COBB Tuning Carbon Fiber Air Scoop!
More informationINSTALLATION INSTRUCTIONS Unitronic DV Relocation Kit for 2.0 TSI Gen2 UH003-ICA
Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included components, tools required, and procedures
More informationARK Exhaust System DT-S Cat-Back. (SM D, 0201D) for Honda CR-Z (1.5L I4 Hybrid LEA)
ARK Exhaust System DT-S Cat-Back (SM0603-0101D, 0201D) for Honda CR-Z (1.5L I4 Hybrid LEA) Congratulations on purchasing an ARK Performance premium exhaust system! Please read and understand the installation
More informationCORKSPORT Power Series Cat Back Exhaust I N S T A L L A T I O N I N S T R U C T I O N S Mazda 6 2.5T PART #: ATK
I N S T A L L A T I O N I N S T R U C T I O N S CORKSPORT Power Series Cat Back Exhaust 2018+ Mazda 6 2.5T PART #: ATK-6-101-12 Need Help With Your Installation? Call (360) 260-CORK PAGE 1 CORKSPORT Power
More informationIE Audi B9 S4, S5, A4, A5, Allroad FDS Intercooler Install Guide IETPCK1
IE Audi B9 S4, S5, A4, A5, Allroad FDS Intercooler Install Guide IETPCK1 Thank you for purchasing the best performing intercooler on the market! This instruction guide is used for installation of IE s
More informationInstallation Instructions
Description Contents Revo Test Pipe or Optional Catalytic Converter Pipe Revo Mid Pipe Revo FWD Reducer Pipe Recommended Tools Quantity Tool Size 1 Hex Key / Socket 6 1 Sockets 13 (deep well) 1 Ratchet
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More informationIntegrated Engineering MK7/MQB Cold Air Intake Install Guide IEINCI2 & IEINCI8
Integrated Engineering MK7/MQB Cold Air Intake Install Guide IEINCI2 & IEINCI8 Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation
More informationCHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS
CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic
More informationInstruction Guide: Infiniti Q50 3.0L VR30DDTT "Full Down Pipes"
480 E. Easy St. Unit #4 Simi Valley, Ca. 93065 Instruction Guide: 2016+ Infiniti Q50 3.0L VR30DDTT "Full Down Pipes" Technical support: (805) 522-3278 Monday- Friday 9a.m.- 3 p.m. PST WARNING: INSTALLATION
More informationARK Exhaust System N-II Cat-Back. (SM N) for Chevrolet Camaro (3.6L V6 LLT/LFX, 6.2L V8 LS3/L99)
ARK Exhaust System N-II Cat-Back (SM0403-0011N) for Chevrolet Camaro (3.6L V6 LLT/LFX, 6.2L V8 LS3/L99) Congratulations on purchasing an ARK Performance premium exhaust system! Please read and understand
More informationARK Exhaust System GRiP Cat-Back. (SM G, 0207D, 0307D) for Infiniti FX35 (3.5L V6 VQ35HR)
ARK Exhaust System GRiP Cat-Back (SM1104-0107G, 0207D, 0307D) for Infiniti FX35 (3.5L V6 VQ35HR) Congratulations on purchasing an ARK Performance premium exhaust system! Please read and understand the
More informationInstallation Guide Turbo Competition X-Pipe Exhaust System
Installation Guide 997.1 Turbo Competition X-Pipe Exhaust System Disclaimer: This installation guide is intended to clarify the installation process of your new Soul Performance Products exhaust. Please
More informationPage1. ISF Stainless Steel Headers // Part# HDR-004
Congratulations on the purchase of your ISF Stainless Steel Headers and thank you for choosing Sikky Manufacturing. This installation manual is intended to guide you through the removal of the factory
More informationEdelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines Part #7179
For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines PLEASE study these instructions carefully before beginning this installation. You should be familiar with and comfortable working on your
More information#TL T DOWNPIPES/ INSTALLATION INSTRUCTIONS
#TL100084 4.0T DOWNPIPES/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for on a North American specification RS7, but other models, like the S6 and S8, are similar. When disassembling
More informationVolkswagen MK6 GTI ECS Valved Exhaust System Installation Instructions
Volkswagen MK6 GTI ECS Valved Exhaust System Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationXDP Complete EGR Race Track Kit w/up-pipe. Item Number: XD144
XDP Complete EGR Race Track Kit w/up-pipe Item Number: XD144 PACKING LIST: 2 - Lined 3/4" SS Hose Clamp 1-3/4 Silicone Hose 1 - XDP Engraved EGR Valve Block-Off Plate with O-ring 1 - EGR Cooler Block-Off
More informationVolkswagen MK5 GTI ECS Valved Exhaust System Installation Instructions
Volkswagen MK5 GTI ECS Valved Exhaust System Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationInstallation Instructions Borla Stinger S-Type Cat-Back Exhaust (05-09 GT)
Installation Instructions Borla Stinger S-Type Cat-Back Exhaust (05-09 GT) Overview: This installation guide will cover installation of the Borla Stinger S-Type Catback Exhaust for all Mustang GTs from
More informationBill of Materials: Please take time to read and understand these installation instructions.
Please take time to read and understand these installation instructions. CORSA recommends that installation of this system be performed by a qualified service center or professional muffler installer who
More informationINTERCOOLER PIPE KIT CHEVY CAMARO 2.0T PARTS LIST AND INSTALLATION GUIDE PARTS INCLUDED CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 2PC ALUMINUM PIPES W/ CNC-MACHINED QUICK-DISCONNECTS 1PC ALUMINUM PIPE W/ CNC-MACHINED 2-BOLT FLANGE 2PC QUICK-DISCONNECT SPRING CLIPS 1PC 2.75" 90 SILICONE COUPLER 1PC 2.25"
More information1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST MUSTANG GT LONG TUBE HEADERS (M30000)
ADVANCED - Installation requires professional-type tools and advanced automotive-service skills. If you lack experience with internal engine modifications, an Advanced installation is probably beyond your
More information2010 Camaro Long Tube Headers, Coated w/high Flow Cats Use w/#30220
PART #30212 2010 Camaro Long Tube Headers, Coated w/high Flow Cats Use w/#30220 PACKING LIST Before installation, use this checklist to make sure all necessary parts have been included. ITEM CHECK PART
More informationProduct: Cadillac ATS 2.0T Downpipe. Part Numbers: Downpipe 2.0T - with catalytic converter Downpipe 2.
Product: Cadillac ATS 2.0T Downpipe Part Numbers: 1180111 Downpipe 2.0T - with catalytic converter 1180112 Downpipe 2.0T - Race Only Applications: Cadillac ATS 2.0T, 2013 - Current Description: These downpipe
More informationWeistec M113K Supercharger System Installation Guide
Weistec M113K Supercharger System Installation Guide WARNING! DO NOT HAVE YOUR ECU REPROGRAMMED ANYWHERE BUT AT WEISTEC FOR THIS SUPERCHARGER. THE AMG 55 USES AN ELECTRONIC THROTTLE CONTROL (ETC), WHICH
More information15-18 FORD MUSTANG GT
15-18 FORD MUSTANG GT IMPORTANT! WARRANTY AND INSTALLATION INSTRUCTIONS Please Forward All Information to Consumer Be sure to review the enclosed instructions prior to beginning the installation process.
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough
More informationThis kit may void factory warranty please check with manufacturer.
Thank you for purchasing a Sinister Manufacturing Company EGR delete kit. Precision manufactured using aircraft quality 304 stainless steel and billet aluminum; this EGR kit is designed to endure years
More information2017+ FORD RAPTOR DOWNPIPE INSTALLATION INSTRUCTIONS
Thanks for purchasing a Stainless Works Downpipe system for your 2017+ Ford Raptor. Our team has done our very best to ensure that this product is the premium in performance, quality, and fitment. We are
More informationADJUSTABLE ANTI-ROLL BAR INSTALLATION INSTRUCTIONS PART NUMBER D PARTS LIST
ADJUSTABLE ANTI-ROLL BAR INSTALLATION INSTRUCTIONS PART NUMBER D120-0580 DESCRIPTION: Front 28mm; 3-hole adjustable APPLICATION: 2014-16 F22 228i/M235i 2015-16 F23 228i/M235i Convertible 2013-16 F30 320i
More informationARK Exhaust System GRiP Cat-Back. (SM G, 0207G, 0307G) for Infiniti G37 Coupe AWD (3.7L V6 VQ37VHR)
ARK Exhaust System GRiP Cat-Back (SM1102-0107G, 0207G, 0307G) for Infiniti G37 Coupe AWD (3.7L V6 VQ37VHR) Congratulations on purchasing an ARK Performance premium exhaust system! Please read and understand
More informationPlease take time to read and understand these installation instructions.
2014- Current C7 Corvette Please take time to read and understand these installation instructions. CORSA recommends that the installation of this system be performed by a qualified service center or professional
More informationEdelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines Part #7179
For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines PLEASE study these instructions carefully before beginning this installation. You should be familiar with and comfortable working on your vehicle.
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More informationInstant Chat off the main page of Or simply call our tech team at
FRONT MOUNT INTERCOOLER 2008-13 STI 2014-04- 08 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
More informationPart Numbers: Complete Kits: C5 Base/Z06 Complete Header Package with Cats C5 Base/Z06 Complete Header Package without Cats
Product: Corvette Tri-Y Headers & Mid-Pipe Part Numbers: Complete Kits: 1150042 C5 Base/Z06 Complete Header Package with Cats 1150043 C5 Base/Z06 Complete Header Package without Cats Applications: Chevrolet
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationModdit. How to Install a Tomei Front Pipe on a Subaru BRZ. This write up will show how to install a front pipe on a BRZ. Written By: Dung Nguyen
Moddit How to Install a Tomei Front Pipe on a Subaru BRZ This write up will show how to install a front pipe on a BRZ. Written By: Dung Nguyen 2017 www.moddit.com Page 1 of 10 INTRODUCTION With the availability
More informationPowerMax Diesel Upgrade For Cummins Engines
PowerMax Diesel Upgrade For Cummins Engines 00.5-007.5 Dodge Ram With Cummins 5.9L Item 3 4 5 6 7 8 9 0 3 4 5 6 7 8 Parts List Description Turbocharger Ancillary kit 773069- (includes) Installation Instructions
More informationMK5 Gen2 GTI Exhaust Installation Instructions
MK5 Gen2 GTI Exhaust Installation Instructions Tools Required Wrenches/sockets: 13, 15, 16, 17, 22 mm Flat-blade screwdriver Penetrating lubricant Summary This document includes instructions for the following
More informationMM010 6TH GEN CAMARO TUBULAR MOTOR MOUNTS
BMR recommends professional installation of this product. A service lift is also recommended for installation of this product. Engine coolant is drained during install. Please review installation instructions
More informationCUSTOM-DIESEL.COM ATTENTION VERY IMPORTANT - PLEASE READ
ATTENTION VERY IMPORTANT - PLEASE READ IF YOU PURCHASED THIS ITEM FROM EBAY, WE WANT YOU TO KNOW THAT EBAY HAS ALWAYS GIVEN YOU, THE BUYER, THE STRENGTH TO VOICE YOUR OPINION OF EBAY SELLERS BY LEAVING
More informationInstallation instructions
Installation instructions Akrapovič Exhaust System: Evolution Link Pipe Set for the BMW M3 (type F80) BMW M4 (type F82) Installation instructions Akrapovič Exhaust System: Evolution Link Pipe Set for
More informationIntegrated Engineering VW Jetta & GLI MK6 ( ) 2.0T/1,8T Gen 3 Cold Air Intake Install
Integrated Engineering VW Jetta & GLI MK6 (2013.5+) 2.0T/1,8T Gen 3 Cold Air Intake Install Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used
More informationCorkSport Mazdaspeed Protégé Intercooler Hoses Mazdaspeed Protégé
CorkSport Mazdaspeed Protégé Intercooler Hoses 2002-2003.5 Mazdaspeed Protégé Thank you for purchasing the CorkSport Mazdaspeed Protégé Intercooler Hose Kit. This kit has been designed and tested to be
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0923 APPLICATION: 2011 E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler Congratulations for being selective enough to
More informationINSTRUCTIONS. INTERCOOLER UPGRADE BMW E82 135i 2008-
INSTRUCTIONS INTERCOOLER UPGRADE BMW E82 135i 2008- Parts Included: - Intercooler - Left and right side pipes with hoses - 3 Silicone Hoses ( 2.5 x 3 ) - 1 Silicone Hose 90degree 2.5 elbow - 8 Hoseclamps
More informationInstallation instructions
Installation instructions Akrapovič Exhaust Systems: Down-Pipe and Link-Pipe for the VW GOLF GTI (type Mk VI.) VW GOLF 1.8TSI (type Mk VI.) www.akrapovic.com Installation instructions Akrapovič Exhaust
More informationInstallation Instructions BILLET/PLUS PISTOL-GRIP SHIFTER Fits: 2016 Camaro V6 with Manual Transmission Catalog #
Installation Instructions BILLET/PLUS PISTOL-GRIP SHIFTER Fits: 2016 Camaro V6 with Manual Transmission Catalog # 3916034 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface
More informationFULL LENGTH HEADERS/ CATTED HEAD PIPES
INSTALLATION INSTRUCTIONS INS232 2016-2018 CAMARO 6.2L V8 FULL LENGTH HEADERS/ CATTED HEAD PIPES Part #4044 and 40440 Special Tools required: 10mm, 12mm, 13mm, 15mm Socket and Wrenches, Pliers, Saw, Welder
More informationHYUNDAI VELOSTER SHORT RAM 1.6T INTAKE INSTALLATION INSTRUCTIONS
Installation: HYUNDAI VELOSTER SHORT RAM 1.6T INTAKE INSTALLATION INSTRUCTIONS Tools needed: 1/4 or 3/8 drive ratchet 12 extension (shorter ones work, but will be difficult to reach some bolts) 10mm socket
More informationCORKSPORT Power Series 80mm Cat Back Exhaust
I N S T A L L A T I O N I N S T R U C T I O N S CORKSPORT Power Series 80mm Cat Back Exhaust 2014-2018 Mazda 3 PART #: AXM-6-102 Need Help With Your Installation? Call (360) 260-CORK PAGE 1 CORKSPORT Power
More informationInstallation Instructions :BMW B58 : Page 1
Installation Instructions :BMW B58 : Page 1 1. We will start by removing the stock airbox system. Loosen the hose clamp around the airbox. Remove the MAF sensor plug the white clip unlocks by pulling it
More information