*THIS KIT IS NOT INTENDED FOR VEHICLES WITH ABS*

Size: px
Start display at page:

Download "*THIS KIT IS NOT INTENDED FOR VEHICLES WITH ABS*"

Transcription

1 *THIS KIT IS NOT INTENDED FOR VEHICLES WITH ABS* Notes: New full-cast rotors from 1990 or newer Wrangler must be used with this kit, this rotor (ITT #65225 or equivalent) has a.25 thick mounting flange. Do not use the factory style composite rotor (.125 thick flange). Rotor pilot hole must be machined to a diameter of to fit the wheel hub *Some factory wheels may not fit over the hub lock body as required. Wheel center hole must be at least 2.78 in diameter. Check your wheels before proceeding. **Rotor pilot hole must be machined to a diameter of to fit the wheel hub** Figure A, APPLICATIONS FOR THE FRONT AXLE WHEEL HUB CONVERSION KIT FOR JEEP WRANGLER, CHEROKEE, AND COMANCHE. 5 on 4.5" wheel bolt pattern, 260X u-joint, 27 spline wrangler/cherokee , PN on 4.5" wheel bolt pattern, 297X u-joint, 27 spline wrangler/cherokee 1995+, PN FEATURES Strong,easy maintenance,replace those non-serviceable parts found on 1984 and newer XJ,YJ and TJ jeeps with MileMarker premium front hub conversion kit. Serviceable bearing and seal SAFETY and CAUTION This sheet provides guidelines to install the Mile Marker front wheel hub conversion kit. During installation, standard safety precautions and equipment should be used where appropriate.

2 TOOLS AND MATERIALS NEEDED Jack ½ Drive Socket Set Jacke-stands 4-Lug Socket for Dana 44 Torque Wrench Safety Goggles 13mm 12 Pt. ½ Drive Socket Shop Rags 4-lug Socket included in kit Figure B, Figure 1. Front axle wheel hub conversion kit. Parts not included in kit are drawn with dashed lines. Item # Part Name (Qty) 1 Hub locks (2) 2 Axle Retainer (2) 3 Spindle Washer (2) 5 Spindle Nut Kit (2) 6 Outer Bearing Cone (2) 7 Outer Bearing Cup (2) 8 Wheel Hub (2) 9 Inner Bearing Cup (2) 10 Inner Bearing Cone (2) 11 Grease Seal (2) 12 Wheel Studs (10) 13 Spindle (2) 14 Needle Bearing (2) 15 Spindle Seal (2) 16 Thrust Washer (2) 17 V-Ring Spindle Seal (2) 18 Seal Shield (2) 19 Outer Axle (2) Using 260X U-joint 19a Outer Axle (2) Using 297X U-joint 20 U-Joint 20a U-Joint Figure C, NOTE: Item numbers replacements can be purchased in kit form, from Spicer using the following part number X.

3 PLEASE READ THE INSTRUCTION THOROUGHLY BEFORE STARTING THE INSTALLATION DISASSEMBLY NOTE: Refer to your authorized Jeep Technical Service Manual for removal instructions. Set the parking brake and chock the rear wheels. Raise the front end and support it on 2 jack stands. Remove the tire and wheel assembly. Figure D, Remove the caliper and hang it from the frame or suspension with a piece of wire, being careful not to strain the brake hose. Remove rotor and three bolts retaining the original hub (using 13mm 12pt. Socket) and bearing assembly. Remove axle shafts, brake shield, hub, and bearing pack. Figure E, Figure F,

4 Separate the original inner shaft from the outer shaft by removing the u-joint. NOTE: Refer to your authorized Jeep Technical Service Manual for removal instructions Figure G, All bearings and seals are installed in kit ROTOR TO WHEEL HUB INSTALLATION Place brake rotor to the wheel hub aligning the holes. Press the studs into the holes. NOTE: Make sure head of stub firmly contacts the brake rotor Figure H,

5 WHEEL HUB INSTALLATION Apply a light coating of grease to the shank of the spindle. Slide wheel hub assembly onto spindle. Figure I, NOTE: Keep wheel hub aligned with spindle so bearing dosn t wedge on spindle. Thread inner nut (Figure C, Flag 5) on to spindle. Using hub spindle nut socket (Figure B) and torque wrench, torque nut to 50 ft-lb. Rotate wheel back and forth while tightening the nut. This helps seat bearings. Loosen the nut ½ turn (180 degrees). Re-torque the nut to 3 to 5 ft-lb. NOTE: All free clearance should be removed from bearings. If not repeat procedure. Install lock washer on spindle. See figure C, flag 5. Thread outer nut spindle. See figure C, flag 5. Torque outer nut to 125 to 150 ft-lb. Figure j, Install lock washer on spindle HUBLOCK INSTALLATION Lube O-ring seal with ANTI-SEIZE NOTE: DO NOT ADD GREASE TO HUBLOCKS. Install snap ring on axle Install Hub assembly (figure C, flag 1) onto the wheel hub aligning over wheel studs. Install wheels and tires. Torque lug nuts. Figure K, NOTE: REPEAT ALL STEPS FOR OTHER SIDE OF VEHICLE.

WRANGLER, CHEROKEE AND COMANCHE, FRONT AXLE WHEEL HUB CONVERSION KIT

WRANGLER, CHEROKEE AND COMANCHE, FRONT AXLE WHEEL HUB CONVERSION KIT WRANGLER, CHEROKEE AND COMANCHE, FRONT AXLE WHEEL HUB CONVERSION KIT -YA WU-07 5 x 4.5 -YA WU-08 5 x 5.5 *THIS KIT IS NOT INTENDED FOR VEHICLES WITH ABS AND YA WU-08 WILL CHANGE BOLT PATTERN TO 5 ON 5.5*

More information

JK 8 Lug Front Locking Hub Conversion Kit

JK 8 Lug Front Locking Hub Conversion Kit JK 8 Lug Front Locking Hub Conversion Kit Kit #3034411 w/ Performance Rotors Kit #3034410 w/ Performance Slotted Rotors Kit #3034412 w/ Big Brake Kit Kit #3034413 w/ Big Brake Kit and Slotted Rotors Important

More information

WARNING: Only perform this installation if you are experienced, fully equipped mechanic.

WARNING: Only perform this installation if you are experienced, fully equipped mechanic. DYNATRAC V3.2 2005-Present Ford Super Duty 250/350-4x4, Front Axle, Free Spin Conversion Kit Some of the less common tools, which will be required: 6 point Spanner socket (OTC #7090-A or equivalent). These

More information

DYNATRAC V6.0. WARNING: Only perform this installation if you are experienced, fully equipped mechanic.

DYNATRAC V6.0. WARNING: Only perform this installation if you are experienced, fully equipped mechanic. DYNATRAC V6.0 1999-2004 Ford Super Duty 250/550-4x4, Front Axle, Free Spin Conversion Kit Some of the less common tools, which will be required: 6 point Spanner socket (OTC #7090-A or equivalent) OR 4

More information

Dodge SpynTec Hub Conversion Kit

Dodge SpynTec Hub Conversion Kit SpynTec SpynTec Industries Installation Instructions for the Dodge SpynTec Hub Conversion Kit I n d u s t r i e s SpynTec Industries LLC. 11501 South Avenue North Lima, Ohio 4445 1.888.90.AXLE Page 1 Warning

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2505 Lowering Spindle Assembly Installation Instructions ½ TON SILVERADO

More information

JK 8 Lug Front Locking Hub Conversion Kit

JK 8 Lug Front Locking Hub Conversion Kit 1 JK 8 Lug Front Locking Hub Conversion Kit Kit #3034411 w/ Performance Rotors Kit #3034410 w/ Performance Slotted Rotors Kit #3034412 w/ Big Brake Kit Kit #3034413 w/ Big Brake Kit and Slotted Rotors

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 2100 DROPPED FRONT SPINDLE CHEVROLET 2WD S-10 / S-15 PICKUP / BLAZER / JIMMY, including models with ABS General Motors G-Body Rear Wheel Drive Cars CONGRATULATIONS! You were selective

More information

1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date:

1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date: 1988 Jeep Truck Wrangler L4-150 2.5L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # 025288 Date: 880711 Right Front Axle Shaft Seal - Installation Models 1986-88 Jeep Comanche,

More information

Front Hub and Disc (4WD Model)

Front Hub and Disc (4WD Model) 4C 8 DRIVE SHAFT SYSTEM Disassembled View Front Hub and Disc (4WD Model) 411RW001 Legend (1) Bolt (2) Cap (3) Snap Ring and Shim (4) Hub Flange (5) Lock Washer and Lock Screw (6) Hub Nut (7) Outer Bearing

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2000 1984 1991 Toyota 2 Wheel Drive Pick-Ups 2 Front Dropped Spindles Congratulations!

More information

JK CRD60 Front Fixed Spindle Conversion Kit

JK CRD60 Front Fixed Spindle Conversion Kit 1 JK CRD60 Front Fixed Spindle Conversion Kit www.teraflex.com Kit # 3060000 JK CRD60 Front Fixed Spindle Conversion Kit Important Notes: Prior to beginning this or any installation read these instructions

More information

1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series

1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - V Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - V Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet

More information

DYNATRAC PRODUCTS V5.3

DYNATRAC PRODUCTS V5.3 DYNATRAC PRODUCTS V5.3 2000-2008 Dodge Hub Kit Stage 1 4x4, Front Axle Free Spin Conversion Kit Note: This Kit is not Approved for 2007 & up 3500 Cab and Chassis Trucks Due to a Larger U-Joint (If U-Joint

More information

Rear Axle Hub, Bearing, Cup, and/or Seal Replacement

Rear Axle Hub, Bearing, Cup, and/or Seal Replacement Page 1 of 11 Rear Axle Hub, Bearing, Cup, and/or Seal Replacement Special Tools J 8092 Universal Driver Handle - 3/4 inch - 10 J 2222-C Wheel Bearing Nut Wrench J 24426 Wheel Bearing Race Installer - Outer

More information

Audi B5 A4/S4 Rear Wheel Bearing Service Kit

Audi B5 A4/S4 Rear Wheel Bearing Service Kit Audi B5 A4/S4 Installation Tutorial ES2561175 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles

More information

Installation Notes: #86000-R Race Series +3.5 L/T Kit

Installation Notes: #86000-R Race Series +3.5 L/T Kit 159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767 3100-3200 3 DROPPED FRONT SPINDLE 73-87 1/2 TON C-10 PICK-UP / 1/2 TON BLAZER

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 2005 2010 DROPPED SPINDLE DATSUN 720 2 WHEEL DRIVE PICK-UPS NISSAN HARDBODY 2WD PICK-UPS Congratulations! You were selective enough to choose a BELLTECH PRODUCT. We have spent

More information

1984 Dodge W250 PICKUP

1984 Dodge W250 PICKUP 1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as

More information

Page 1 of 5 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2000 Spindle, RH and LH Shaft and Joint

More information

JK 8-Lug Front Full Float Kit

JK 8-Lug Front Full Float Kit 1 Kit #3034411 w/ Performance Rotors Kit #3034410 w/ Performance Slotted Rotors Kit #3034412 w/ Big Brake Kit Kit #3034413 w/ Big Brake Kit and Slotted Rotors JK 8-Lug Front Full Float Kit www.teraflex.com

More information

Audi B6/B7 A4/S4 Rear Wheel Bearing Service Kit

Audi B6/B7 A4/S4 Rear Wheel Bearing Service Kit Audi B6/B7 A4/S4 Installation Tutorial ES2561175 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles

More information

4. Rear Axle REAR AXLE

4. Rear Axle REAR AXLE REAR AXLE DRIVE SHAFT SYSTEM 4. Rear Axle A: REMOVAL 1) Disconnect the ground cable from battery. 2) Lift-up the vehicle, and remove the rear wheel. 3) Unlock the axle nut. 4) Remove the axle nut using

More information

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES 2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential

More information

QA1 Caster Camber Plates (79-89 all)

QA1 Caster Camber Plates (79-89 all) Time Needed: About 2 hours QA1 Caster Camber Plates (79-89 all) Tools Needed: Socket for lug nuts 13/16 or 6 spline tool is the most common, 17mm socket, 15/16 socket, ¾ socket, 9/16 socket, 15/16 wrench,

More information

Installation Instructions

Installation Instructions Installation Instructions Product: ACOS Pro Part Number: PN 2700 Applications: Jeep Wrangler TJ, 1997-06 (front or rear) Jeep Grand Cherokee ZJ, 1993-98 (front only) Jeep Cherokee XJ, 1984-01 (front only)

More information

Page 1 of 7 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 06/19/2000 Hubs, Automatic Lock Refer to Section

More information

Suspension Upgrade System RS66152 (Upper Adjustable Control Arms)

Suspension Upgrade System RS66152 (Upper Adjustable Control Arms) 89152 Rev B Suspension Upgrade System RS66152 (Upper Adjustable Control Arms) Fits 1997-2006 Jeep Wrangler (TJ / LJ). 89152 Rev B READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING

More information

Inspection and Verification, Ranger

Inspection and Verification, Ranger file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk53a03.htm~gen~ref.htm Page 1 of 1 Section 05-03A: Wheel Hubs and Bearings, Front Wheels, 4- Wheel Drive DIAGNOSIS AND TESTING 1997 Ranger 4x4 with Dana

More information

97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT

97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT 921663U00 97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT Thank you for choosing Rough Country for your suspension needs. This kit is an upgrade kit only. This kit includes frame mounting points and adjustable long

More information

DYNATRAC PRODUCTS V1.3

DYNATRAC PRODUCTS V1.3 DYNATRAC PRODUCTS V1.3 2007-2017 Jeep JK Wrangler ProGrip Performance Brake Kit Front & Rear Required tools: 13mm wrench 15mm wrench 18mm socket 21mm socket Calibrated torque wrench. Anti-Seize compound.

More information

kit contents trail-safe samurai inner axle seal suzuki samurai (all engines) InstalLation Instructions

kit contents trail-safe samurai inner axle seal suzuki samurai (all engines) InstalLation Instructions InstalLation Instructions trail-safe samurai inner axle seal 300748-3-kit 1986-1995 suzuki samurai (all engines) kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950

More information

07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES

07-13 TOYOTA TUNDRA 2WD 6 LIFT SPINDLES MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714-630-0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: K886764 07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES PARTS LIST QTY LIFT

More information

Service Bulletin No. 2874

Service Bulletin No. 2874 MODEL TYPE SECTION/GROUP DATE SUBJECT 102 E / E4500 / J4500 Series Coaches Service Information 04--Brakes MERITOR BRAKE CALIPER SERVICE PARTS CHART Dec. 24, 2003 CONDITIONS may be purchased from MCI Service,

More information

M-2300-T 6-Piston Mustang Brake Kit INSTALLATION INSTRUCTIONS

M-2300-T 6-Piston Mustang Brake Kit INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS

'99-03 CHEVROLET/GMC IFS 4WD 6 SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS 1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 2500 DROPPED FRONT SPINDLE CHEVROLET C / K and G.M.C. SIERRA 1500 / 2500 / 3500 Pick-Ups Congratulations! You were selective enough to choose a BELLTECH PRODUCT. We have spent

More information

FRONT & 4 REAR GM WD LOWERING KIT

FRONT & 4 REAR GM WD LOWERING KIT 92725200 88-98 2 FRONT & 4 REAR GM 1500 2WD LOWERING KIT Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition

More information

M-1007-DC1785 Raptor Bead-Lock Off Road Wheel INSTALLATION INSTRUCTIONS

M-1007-DC1785 Raptor Bead-Lock Off Road Wheel INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

INSTALLATION INSTRUCTIONS 88518

INSTALLATION INSTRUCTIONS 88518 INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:

More information

Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014. Axle

Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014. Axle 204-01 Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014 Axle 1 N620604 Axle pivot nut 2 N806859 Axle pivot bolt 3 3007 LH/ 3006 RH LH/ 3006 RH Axle Removal NOTICE:

More information

LIMITED SLIP DIFFERENTIAL INSTALLATION

LIMITED SLIP DIFFERENTIAL INSTALLATION Installation of the limited slip gear can be done with axle out of car or with car lifted to gain access from underneath. Refer to repair manual for proper lifting instructions if car is to be lifted.

More information

INSTALLATION INSTRUCTIONS 88029

INSTALLATION INSTRUCTIONS 88029 INSTALLATION INSTRUCTIONS 88029 FOR SUSPENSION SYSTEMS RS6503: JEEP WRANGLER (TJ) READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION REV F IMPORTANT NOTES! WARNING: This

More information

ALLOY USA AXLE INSTALLATION (99-04 GT, Mach 1)

ALLOY USA AXLE INSTALLATION (99-04 GT, Mach 1) ALLOY USA AXLE INSTALLATION (99-04 GT, Mach 1) Time Necessary: Approximately 4 hours Tools Required: Wrenches: 8mm, 13mm, 15mm, 5.5 mm allen, 6mm allen Sockets: 5/8, 3/4 Ratchet Floor Jack Jack Stands

More information

HUB - DRUMS - DISC JEEP CJ AVANT FRONT

HUB - DRUMS - DISC JEEP CJ AVANT FRONT HUB - DRUMS - DISC JEEP CJ 72-86 AVANT FRONT 1 300101 Wheel bearing seal drum brake (CJ 72-78) 2.125" spindle diameter 2 300102 Wheel bearing seal disc brake (CJ 77-86) 2.313" spindle diameter 3 300103

More information

INSTALLATION INSTRUCTION 88146

INSTALLATION INSTRUCTION 88146 INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING

More information

nissan patrol birfield kit

nissan patrol birfield kit nissan patrol birfield kit 300795-kit 1987-1997 nissan patrol gr(y60) 1988-1994 ford maverick 1987-1997 nissan patrol gq 1987-1997 nissan patrol safari 1987-1997 nissan safari kit contents 5356 PINE AVE

More information

Anti-Sway Bars Installation Instructions For Mazda MX-5 PART #

Anti-Sway Bars Installation Instructions For Mazda MX-5 PART # Anti-Sway Bars Installation Instructions For 2006+ Mazda MX-5 PART # 920-330 Tools required: A jack and jack stands, 5mm Allen wrench, ratchet, 10mm, 12mm and 14mm, combination wrenches and sockets, 21mm

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION AXLE SHAFTS & BEARINGS Removal CAUTION: Failure to turn off air suspension power before raising vehicle may result in unexpected inflation or deflation of air springs. DO NOT reconnect

More information

2014 F /6 LIFT KIT

2014 F /6 LIFT KIT 92157500 2014 F-150 4 /6 LIFT KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions,

More information

Page 1 of 6 Axle Shaft, Hub, Oil Seal and Outer Wheel Bearing SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Locknut Wrench T85T-4252-AH Removal 1. Set the parking brake and loosen the eight

More information

Steer Axles. Spicer. Service Manual. AXSM-0070 November Front Drive Steer Axle Model 60

Steer Axles. Spicer. Service Manual. AXSM-0070 November Front Drive Steer Axle Model 60 Spicer Steer Axles Service Manual AXSM-0070 November 2017 Front Drive Steer Axle Model 60 General Information The description and specifications contained in this service publication are current at the

More information

Loosen the lug nuts. 1. Remove the center cap. 2. With the weight of the vehicle on the wheels, loosen the lug nuts.

Loosen the lug nuts. 1. Remove the center cap. 2. With the weight of the vehicle on the wheels, loosen the lug nuts. Section 204-01B: Front Suspension 4x4 REMOVAL AND INSTALLATION 1997 F-150, F-250 Workshop Manual Wheel Hub Special Service Tool(s) Bearing Cup Replacer T80T-4000-P Seal Replacer T96T-1175-A Threaded Drawbar

More information

CHEVY C WHEEL DRIVE STANDARD CAB ONLY (EXCEPT 454SS) FTS1588-7BC 4" LIFT SPINDLES

CHEVY C WHEEL DRIVE STANDARD CAB ONLY (EXCEPT 454SS) FTS1588-7BC 4 LIFT SPINDLES 1988-1991 CHEVY C1500 2 WHEEL DRIVE STANDARD CAB ONLY (EXCEPT 454SS) FTS1588-7BC 4" LIFT SPINDLES PARTS LIST: 1 EA. LIFT SPINDLE PASS. SIDE FT1588-7BCP 1 EA. LIFT SPINDLE DRIVER'S SIDE FT1588-7BCD 6 EA.

More information

INSTALLATION INSTRUCTION Rev A

INSTALLATION INSTRUCTION Rev A INSTALLATION INSTRUCTION 88587 Rev A FOR RANCHO SUSPENSION SYSTEM RS6587B: 2009 DODGE RAM 1500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:

More information

Installation Instructions. 6 Basic System FTS21060BK / FTS21061BK / FTS21042BK GM 2WD C1500 P/U ONLY

Installation Instructions. 6 Basic System FTS21060BK / FTS21061BK / FTS21042BK GM 2WD C1500 P/U ONLY Installation Instructions 6 Basic System FTS21060BK / FTS21061BK / FTS21042BK 2007-13 GM 2WD C1500 P/U ONLY 2007-13 GM 1500 Truck Basic System FTS21060BK / FTS21061BK / FTS21042BK 2007-13 GM 2WD C1500

More information

How to install Front Brake Pads on your GT, V6

How to install Front Brake Pads on your GT, V6 Time Necessary: Approximately 1.5 hours Tools Required: How to install Front Brake Pads on your 99-04 GT, V6 Jack Jack stands Torque wrench Ratchet Lug wrench 15mm socket 12mm socket Large C-clamp Syringe

More information

XJ CHEROKEE LIFT KIT

XJ CHEROKEE LIFT KIT 921633XN200 Thank you for choosing Rough Country for your suspension needs. 84-01 4.5 XJ CHEROKEE LIFT KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

INSTALLATION INSTRUCTION 88581

INSTALLATION INSTRUCTION 88581 INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES! WARNING: This suspension

More information

ADVANCE ADAPTERS INC. Fixed Yoke kit (S.Y.E. Kit)

ADVANCE ADAPTERS INC. Fixed Yoke kit (S.Y.E. Kit) ADVANCE ADAPTERS INC. Fixed Yoke kit (S.Y.E. Kit) Instruction Sheet P/N: 50-7905 & 50-7906 KIT CONSISTS OF: No. Qty Part No. Description 1. 1 51-7906 TAILHOUSING, DIECAST 2. 1 52-7905 SHAFT, MAIN OUTPUT

More information

Installation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited)

Installation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited) Installation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited) Installation Time: 6 Hours Tools Required: Floor Jack Jack Stands Ratchet Torque Wrench 15mm Socket 15mm

More information

Installation Instructions

Installation Instructions Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to

More information

INSTALLATION INSTRUCTION 88148

INSTALLATION INSTRUCTION 88148 INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION

More information

X Jeep / Eagle Model 30 /181 Disconnect Front Axles for. XJ (Cherokee /Comanche) YJ /TJ (Wrangler)

X Jeep / Eagle Model 30 /181 Disconnect Front Axles for. XJ (Cherokee /Comanche) YJ /TJ (Wrangler) Jeep / Eagle 1984-1996 Model 30 /181 Disconnect Front Axles for XJ (Cherokee /Comanche) YJ /TJ (Wrangler) 309 Exploded View 310 X510-3 Parts Listing ITEM NO. PART NUMBER DESCRIPTION 1 (3) Housing Axle

More information

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Ford F150 4WD 4" Suspension Lift Kit

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Ford F150 4WD 4 Suspension Lift Kit 2015 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front Brake Line

More information

ALLDATA Online Dodge Truck Caravan V L - Front. Front

ALLDATA Online Dodge Truck Caravan V L - Front. Front Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1994 Dodge Truck Caravan V6-201 3.3L Conversion Calculator Vehicle

More information

SUSP-09, Rear Wheel Bearing Replacement - Steel Trailing Arm. Acrobat Printable Version

SUSP-09, Rear Wheel Bearing Replacement - Steel Trailing Arm. Acrobat Printable Version SUSP-09, Rear Wheel Bearing Replacement - Steel Trailing Arm Introduction Acrobat Printable Version I'd like to thank Ben Davis for providing the pictures for this procedure. Ben took the time to take

More information

Mirrored from:

Mirrored from: Mirrored from: http://www.wranglerforum.com/f274/install-synergy-suspension-ball-joints-write-up-147062.html 03-18-2012, 02:43 AM #1 SilverSport Supporting Member WF Supporting Member Install Synergy Suspension

More information

SAFETY RECALL Volvo Trucks North America Greensboro, NC USA

SAFETY RECALL Volvo Trucks North America Greensboro, NC USA SAFETY RECALL Greensboro, NC USA This Safety Recall replaces recall, RVXX1403, Disc Brake Caliper Bolts, Dated (10.2014). Date Number Release Page 12.2014 1 (11) RVXX1403 02 DISC BRAKE CALIPER BOLTS VAH,

More information

TC Series Front Axle. TC Series Front Axle 010-1

TC Series Front Axle. TC Series Front Axle 010-1 TC Series Front Axle Blue Bird Corporation assumes sole responsibility for ensuring that the information provided herein is accurate to the best of its knowledge at the time of printing. In keeping with

More information

Class 8.8 Class MM 18ft/lbs 23 ft/lbs 10MM 32ft/lbs 45ft/lbs 12MM 55ft/lbs 75ft/lbs 14MM 85ft/lbs 120ft/lbs

Class 8.8 Class MM 18ft/lbs 23 ft/lbs 10MM 32ft/lbs 45ft/lbs 12MM 55ft/lbs 75ft/lbs 14MM 85ft/lbs 120ft/lbs 92190500 Jeep Grand Cherokee 93-98 ZJ 4 Longarm Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these

More information

Fig. 1: Exploded view of the 2WD hub and bearings

Fig. 1: Exploded view of the 2WD hub and bearings Page 1 of 8 Front Wheel Bearings REPLACEMENT NOTE: Sodium-based grease is not compatible with lithium-based grease. Read the package labels and be careful not to mix the two types. If there is any doubt

More information

INSTALLATION INSTRUCTION 88088

INSTALLATION INSTRUCTION 88088 INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:

More information

KG09100BK / KG09101BK GM WD.

KG09100BK / KG09101BK GM WD. KG09100BK / KG09101BK GM. 1988-2006 2 WD. KG09101BK KG09100BK Instruction Sheet: P10476-05 2013 Daystar Products International Inc. Tools Needed Quantity Description 1 Floor Jack 2 Jack Stands 2 Wheel

More information

2000 F-Super Duty /Excursion/F-53 Motorhome Chassis Workshop Manual

2000 F-Super Duty /Excursion/F-53 Motorhome Chassis Workshop Manual Page 1 of 6 SECTION 205-02E: Wheel Hubs and Bearings Full Floating Axle Ford 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date:

More information

2 Suspension System. Suzuki Sidekick/ Geo Tracker, Suzuki Vitara. Part#:

2 Suspension System. Suzuki Sidekick/ Geo Tracker, Suzuki Vitara. Part#: Part#: 037201 2 Suspension System Suzuki Sidekick/ Geo Tracker, Suzuki Vitara Rev. 062615 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 Web/live chat: www.bds-suspension.com. E-mail: tech@bds-suspension.com

More information

Max IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements.

Max IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements. Max IV Rear Axle Replacement For models after Serial Number 19089 and all rear splined axle replacements. 10/8/03 Max IV Snap Ring Rear Axle replacement.doc Tools required: 9/16 Wrench 6 Extension Steel

More information

InstalL Instructions. fj40 knuckle conversion kit. kit contents

InstalL Instructions. fj40 knuckle conversion kit. kit contents InstalL Instructions fj40 knuckle conversion kit 1960-1983 toyota fj40 1960-1983 toyota fj45 304149-1-kit 304150-1-kit 304151-1-kit 304152-1-kit 304153-1-kit 304154-1-kit 304155-1-kit 304156-1-kit 304157-1-kit

More information

Install rubber bump stop thru the tab on the left side of bumper. Use stainless steel 1/4 cap nut to tighten in place.

Install rubber bump stop thru the tab on the left side of bumper. Use stainless steel 1/4 cap nut to tighten in place. Install rubber bump stop thru the tab on the left side of bumper. Use stainless steel 1/4 cap nut to tighten in place. Install the nylon scuff block with 1 steel spacer under it, use 2 @ 1/4 X1 1/4 SS

More information

Front Wheel Bearing - New Replacement Procedures 55E230 APRIL Eagle Comanche Cherokee-Wagoneer 1987 Wrangler-YJ

Front Wheel Bearing - New Replacement Procedures 55E230 APRIL Eagle Comanche Cherokee-Wagoneer 1987 Wrangler-YJ 1987 Jeep Truck Wrangler L4-150 2.5L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # 55E230 Date: 870401 Front Wheel Bearing - New Replacement Procedures 55E230 APRIL 1987

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 2102 LOWERING SPINDLE ASSEMBLY 1998-UP CHEVROLET / GMC BLAZER / X-TREME / JIMMY / ENVOY 2 Wheel Drive Congratulations! You were selective enough to choose a BELLTECH PRODUCT.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A136-1 1976-86 AMC 20 AXLES WITH WARN FULL FLOATING AXLE CONVERSION Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.

More information

SERVICE MANUAL L130B / L4130 Series Logstacker Drive Axle With Bolt-On Stub End Retainer

SERVICE MANUAL L130B / L4130 Series Logstacker Drive Axle With Bolt-On Stub End Retainer SERVICE MANUAL L130B / L4130 Series Logstacker Drive Axle With Bolt-On Stub End Retainer Page 1 Allied Form #80-930 Rev 07/2009 SERVICE MANUAL LOG STACKER DA202 DRIVE AXLE TABLE OF CONTENTS PROCEDURE FOR

More information

Installing Rear Brake Pads on a WK Jeep

Installing Rear Brake Pads on a WK Jeep Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after

More information

BRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS

BRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica

More information

Suspension System RS6582B

Suspension System RS6582B Suspension System RS6582B Tahoe/Yukon READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance

More information

Jeep Wrangler (JK) Present

Jeep Wrangler (JK) Present 89107 Rev H Suspension System RS66107 / RS66107B (3 TRAIL SYSTEM) 2012 NEWER JEEP MODELS EQUIPPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT

More information

Electric to Hydraulic Disc Brake Conversion

Electric to Hydraulic Disc Brake Conversion Electric to Hydraulic Disc Brake Conversion Installation and Owner s Manual (For Aftermarket Applications) Table of Contents Introduction... 1 Document Information... 1 Trailer Axle Brake Inspection...

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A128-4 1997-2004 JEEP WRANGLER (TJ) WITH DANA 44 AXLES (non-abs) Thank you for choosing STAINLESS STEEL BRAKES for your braking needs. Pleases take the

More information

DIFFERENTIALS & AXLE SHAFTS

DIFFERENTIALS & AXLE SHAFTS DIFFERENTIALS & AXLE SHAFTS 2001 Chevrolet Camaro 2000-01 DRIVE AXLES General Motors Differentials & Axle Shafts Chevrolet; Camaro Pontiac; Firebird DESCRIPTION & OPERATION Drive axle is a semi-floating,

More information

See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )

See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( ) Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls

More information

X Jeep / Eagle Model 44 /216 Front Axles for. 4 x 2, Military, J10, J20, Cherokee, Honcho, Wagoneer, Grand Wagoneer

X Jeep / Eagle Model 44 /216 Front Axles for. 4 x 2, Military, J10, J20, Cherokee, Honcho, Wagoneer, Grand Wagoneer X510-9 Jeep / Eagle 1978-1992 Model 44 /216 Front Axles for 4 x 2, Military, J10, J20, Cherokee, Honcho, Wagoneer, Grand Wagoneer 329 Exploded View X510-9 330 X510-9 Parts Listing ITEM NO. PART NUMBER

More information

INSTALLATION INSTRUCTION 88051

INSTALLATION INSTRUCTION 88051 INSTALLATION INSTRUCTION 88051 For Rancho Suspension System RS6551: Chevrolet 2500 Suburban & 2500 Avalanche READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT

More information

Installation Instructions

Installation Instructions Installation Instructions 6 Suspension System FTS25005BK / FTS25006BK 2006-2012 Nissan Frontier 2wd/4wd SHORT BED ONLY Tool List: (not included) Floor Jack & Jack Stands Assorted Metric & S.A.E Sockets

More information

1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions

1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT

More information

PRE-INSTALLATION Ford F150 4WD 4" Suspension Lift Kit

PRE-INSTALLATION Ford F150 4WD 4 Suspension Lift Kit 2009-2013 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 25007 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front

More information

for Audi B6 A4/S4 Installation Procedures Front Wheel Bearing Replacement This tutorial is provided as a courtesy by ECS Tuning.

for Audi B6 A4/S4 Installation Procedures Front Wheel Bearing Replacement This tutorial is provided as a courtesy by ECS Tuning. Installation Procedures Front Wheel Bearing eplacement for This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2509 2 DROP SPINDLE 2WD 4WD AWD >>> Must Use 17 Wheels or larger

More information

Yukon Gear & Axle D30, D44 & GM 8.5" Hardcore Locking Hub Installation Guide

Yukon Gear & Axle D30, D44 & GM 8.5 Hardcore Locking Hub Installation Guide Yukon Gear & Axle D30, D44 & GM 8.5" Hardcore Locking Hub Installation Guide PLEASE READ COMPLETELY BEFORE INSTALLATION Application Guide: YHC70005 D30 & D44 30spl - YA WU-08 Spin Free - D30, 30 spline

More information