Testing and Reporting Requirements for Linear Replacement Lamps

Transcription

1 Testing and Reprting Requirements fr Linear Replacement Lamps The DLC defines all tube-style LED prducts that use the lamp hlders (i.e. sckets r tmbstnes) in the luminaire t mechanically r electrically cnnect t the fixture husing and electric supply t fall under these testing requirements. Prducts that d nt emply lamp hlders will be classified as Retrfit Kits, regardless f frm factr. Please see the Prduct Eligibility page and Technical Requirements fr mre details n prduct classificatin. The DLC accepts QPL applicatins fr tw-ft, three-ft, fur-ft, eight-ft, and U-Bend Linear Replacement Lamps. The Testing and Reprting Requirements described belw are intended t evaluate the perfrmance f the lamp itself, and its perfrmance in an apprpriate reference fixture, representative f the mst cmmn applicatin fr each flurescent replacement lamp type. General Applicatins Tw-ft, three-ft, and U-bend replacement lamp general applicatins are restricted t LED lamps intended t replace flurescent T8. Eight-ft replacement lamps are restricted t lamps intending t replace T8 flurescent lamps. Fur-ft replacement lamp general applicatins are restricted t LED lamps intended t replace flurescent T8, T5, and T5HO lamps at this time. Prduct specificatin sheets must clearly indicate fr which specific linear replacement lamp type (i.e. T8, T5, r T5HO) the prduct is intended, and list the base type and the nminal length in inches. T8 Tw-Ft Linear Replacement Lamps LED lamps intended t replace T8 flurescent lamps. These LED lamps shall be 24 inches lng and emply a G13 base. Marketing material shall indicate that they are intended t replace T8 flurescent lamps f the same length. Prducts f different lengths and bases are nt eligible under this general applicatin. Prducts intended t perate n magnetic ballasts are nt eligible. Testing and Reprting Requirements fr Linear Replacement Lamps Page 1 f 17

2 T8 Three-Ft Linear Replacement Lamps LED lamps intended t replace T8 flurescent lamps. These LED lamps shall be 36 inches lng and emply a G13 base. Marketing material shall indicate that they are intended t replace T8 flurescent lamps f the same length. Prducts f different lengths and bases are nt eligible under this general applicatin. Prducts intended t perate n magnetic ballasts are nt eligible. T8 Fur-Ft Linear Replacement Lamps LED lamps intended t replace T8 flurescent lamps. These LED lamps shall be 48 inches lng and emply a G13 base. Marketing material shall indicate that they are intended t replace T8 flurescent lamps f the same length. Prducts f different lengths and bases are nt eligible under this general applicatin. Prducts intended t perate n magnetic ballasts are nt eligible. T5 Fur-Ft Linear Replacement Lamps LED lamps intended t replace T5 flurescent lamps (nte, nt T5 High Output r T5HO). These LED lamps shall be 46 inches lng and emply a G5 base. Marketing material shall indicate that they are intended t replace T5 flurescent lamps f the same length. Prducts f different lengths, bases, r marketed as intended t replace ther types f flurescent lamps are nt eligible under this general applicatin. T5HO Fur-Ft Linear Replacement Lamps LED lamps intended t replace T5HO flurescent lamps. These LED lamps shall be 46 inches lng and emply a G5 base. Marketing material shall indicate that they are intended t replace T5HO flurescent lamps f the same length. Prducts f different lengths, bases, r marketed as intended t replace ther types f flurescent lamps are nt be eligible under this general applicatin. T8 Eight-Ft Linear Replacement Lamps LED lamps intended t replace T flurescent lamps. These LED lamps shall be 96 inches lng and emply a FA8 base. Marketing material shall indicate that they are intended t replace T flurescent lamps f the same length. Prducts f different lengths and bases are nt eligible under this general applicatin. Prducts intended t perate n magnetic ballasts are nt eligible. Testing and Reprting Requirements fr Linear Replacement Lamps Page 2 f 17

3 U-Bend Replacement Lamps LED lamps intended t replace T8 flurescent lamps. These LED lamps shall emply a G13 base. Marketing material shall indicate that they are intended t replace T8 flurescent lamps f the same shape. Prducts f different bases are nt eligible. Primary Use Designatins Under the Technical Requirements Table, replacement lamps will fall under ne f the fllwing fur Primary Use Designatins: Replacement Lamps (UL Type A): Tw-ft, three-ft, fur-ft, eight-ft, and U-bend LED "tubes" designed t replace tw-ft, three-ft, fur-ft, eight-ft, and U-bend flurescent lamps, respectively. Prducts in this primary use designatin emply lamp hlders t cnnect t the fixture being retrfitted and are designed t be "plug and play" replacements fr flurescent lamps. That is, prducts in this categry perate utilizing an existing flurescent ballast, and d nt require mechanical r electrical changes t the fixture. Nte that due t testing cnsideratins, at this time nly prducts that perate utilizing specific ballasts types are eligible. Please see Fixture Level Test requirements belw. Replacement lamps designed t perate utilizing magnetic ballasts r ther types f electrnic ballasts nt specified are nt eligible at this time. Internal Driver/Line Vltage Lamp-Style Retrfit Kits (UL Type B): Tw-ft, three-ft, fur-ft, eight-ft, and U-bend LED "tubes" designed t replace tw-ft, three-ft, fur-ft, eight-ft, and U-bend flurescent lamps, respectively. Prducts in this categry emply lamp hlders t cnnect t the fixture being retrfitted, but d nt perate utilizing the existing flurescent ballast. These prducts require rewiring f the existing fixture t bypass the ballast and send line vltage directly t the lamp hlders. External Driver Lamp-Style Retrfit Kits (UL Type C): Tw-ft, three-ft, fur-ft, eight-ft, and U-bend LED "tubes" designed t replace tw-ft, three-ft, fur-ft, eight-ft, and U-bend flurescent lamps, respectively. Prducts in this categry emply lamp hlders t cnnect t the fixture being retrfitted, d nt perate utilizing the existing flurescent ballast, and require rewiring f the existing fixture t replace the Testing and Reprting Requirements fr Linear Replacement Lamps Page 3 f 17

4 ballast with an external driver. The lamp hlders are then wired t receive nly the lw-vltage electricity that is supplied by that external driver. Dual Mde Internal Driver (UL Type A and Type B): Tw-ft, three-ft, fur-ft, eight-ft, and U-bend LED "tubes" designed t replace tw-ft, three-ft, fur-ft, eight-ft, and U-bend flurescent lamps, respectively. Prducts in this categry perate utilizing the existing flurescent ballast and als have the ability t perate utilizing line vltage if the fixture is rewired t bypass the ballast. These prducts cnnect t the fixture using standard pin-base cnnectins t the lamp hlders. Nte that due t testing cnsideratins, at this time nly prducts that perate utilizing specific ballasts types are eligible. Please see testing requirements belw. Replacement lamps designed t perate utilizing magnetic ballasts, r ther types f electrnic ballasts nt specified, are nt eligible at this time. Fr testing purpses, the DLC requires testing f bth the bare lamp and lamps installed in a typical fixture husing. These typical fixture husings are intended t prvide testing results f the mst cmmn applicatins in which these prducts are used, including representative thermal cnditins f the fixtures in which the lamps wuld be installed. In specifying these fixture husings, the DLC des nt endrse r exclude any particular make r mdel frame fr use in energy efficiency prgrams. Supprting Dcumentatin Applicants shall prvide the fllwing supprting dcumentatin in additin t the test data described belw. Installatin Instructins Installatin instructin sheets must be submitted with the applicatin t indicate hw the replacement lamp will be installed in an existing fixture in the field. This must be prvided in additin t all necessary dcumentatin required fr ther prduct categries. Lamps that require specialized cmpnents fr installatin t perfrm t the abve criteria are nt eligible fr qualificatin. Lamps that emply rtatable end-caps are eligible, but must clearly indicate this feature in the prduct spec sheet. Testing and Reprting Requirements fr Linear Replacement Lamps Page 4 f 17

5 Safety Certificatin Dcumentatin DLC has updated the Safety Certificatin Dcumentatin requirements and prcesses. The dcumentatin required fr the lamp under the new plicy must be submitted with the crrespnding applicatin. Please review the updated Safety Certificatin Dcumentatin detailed requirements utlined in the V4.3 Primary Technical Requirements page released with this dcument. Bth plicies will be fficially implemented n March 26 th, Lamp Level Tests All lamps seeking qualificatin by the DLC must test the bare lamp accrding t LM- 79. Table 1: Individual Replacement Lamp Criteria: T8, T5, and T5HO Replacements Individual Lamp Criteria Tw-ft Lamps, T8 replacements Three-ft Lamps, T8 replacements Fur-ft Lamps, T8 replacements Fur-ft Lamps, T5 replacements Fur-ft Lamps, T5HO replacements Eight-ft Lamps, T8 replacements U-bend Lamps, T8 replacements System Efficacy 110 lm/w 110 lm/w 110 lm/w 110 lm/w 110 lm/w 110 lm/w 110 lm/w Initial Light Output Crrelated Clr Temp. (CCT) Clr Rendering Index (CRI) 800 lm 1,200 lm 1,600 lm 1,600 lm 3,200 lm 3,200 lm 1,400 lm 5000K 5000K 5000K 5000K 5000K 5000K 5000K Pwer Factr Ttal Harmnic Distrtin 20% 20% 20% 20% 20% 20% 20% Testing Ntes Fr T8 replacement lamps designed t perate utilizing existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart ballast. Fr T5 and T5HO replacement lamps designed t perate utilizing existing flurescent ballasts, testing must be cnducted using a nrmal 1.0 ballast factr, electrnic prgrammed-start ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and Testing and Reprting Requirements fr Linear Replacement Lamps Page 5 f 17

6 mdel number must be nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards and must cmply with applicable ANSI standards. Fr Type B and Type C prducts (i.e. lamp-style retrfit kits, which cnnect mechanically and/r electrically t the fixture via standard lamp hlders, but which require an electrical mdificatin t the existing fixture), lamp -level testing is als required. If the system is designed t perate multiple lamps utilizing an external driver, the driver shuld be laded as it wuld be in the field, with apprpriate steps taken t calculate the efficacy f the single lamp. Fr example, fr a tw-lamp kit, ne lamp shuld be measured fr light utput, while the system as intended (with tw identical lamps n the driver) shuld be measured fr electrical input. The wattage int the driver can then be divided by tw, and that wattage divided int the lamp lumens t determine system efficacy. Fr questins, please cntact applicatins@designlights.rg. Fixture Level Tests: Tw-Ft Linear Replacement Lamps Please nte that at the time f this release, lamps intended t replace T5-diameter flurescents are nly eligible in the fur-ft categries. Only lamps intended t replace T8 flurescents are currently eligible in the 2-ft categries. All lamps seeking qualificatin must be tested inside in a reference trffer. Type A, Type B, and Dual-mde tw-ft lamps shall test with three (3) lamps installed in an apprpriate reference trffer. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system; ne, tw, three, and fur lamp Type C systems are eligible. The reference trffer may be any f the fllwing, r a pre-apprved equivalent: Lithnia 2GT8 lensed 2x2 Lithnia 2SP8 lensed 2x2 Lithnia 2PM3 9 cell 2x2 parablic Clumbia Lighting lensed 2x2 4PS22 Clumbia Lighting P222 9 cell 2x2 parablic Pre-apprved equivalent A.L.P. EL-2x2-20-* (*= # f lamps) Saylite 131-A-2-17-E120 Mnmuth Lighting Crp RF24 Simkar Crpratin TY Lensed Trffer 2x2 Testing and Reprting Requirements fr Linear Replacement Lamps Page 6 f 17

7 Jun Lighting Grup S2x2BL LSI LA/FLA 2x2 Clumbia Lighting JT822 Visineering Crp. ERCTB 2x2 US Energy Sciences YTR-02-5 Pre-apprved Equivalents The DLC des nt endrse r exclude any particular make r mdel f reference fixture. Optins listed are intended t illustrate cmmn fixtures f the apprpriate type. Manufacturers may test in alternative fixtures t thse listed, with preapprval frm the DLC. Pre-apprved fixtures must meet the fllwing cnditins: Alternative fixtures must be cmmnly used in the applicatin categry intended fr which they are t be applied. Dcumentatin may be required t demnstrate fixtures apprpriate use if questins arise. Alternative fixtures must prvide similar thermal envirnments t thse listed. Particularly, alternative fixtures may nt be significantly different in internal vlume r cnstructin materials. Table 2: In-situ Testing Perfrmance Requirements: Tw-Ft Linear T8 Replacement Lamps In-situ Lamp Criteria fr Tw-Ft Linear Replacement Lamps Luminaire Efficacy Minimum Initial Luminaire Light Output Spacing Criteria Lumen Maintenance L lm/w 2 lamps installed = 1,350 lm 3 lamps installed = 2,000 lm 4 lamps installed = 2,700 lm Spacing Criteria: = = Znal Lumen Distributin: 0-60 : 75% 50,000 hurs Lumen Maintenance LM-80 fr the package/mdule/array (6,000 hurs minimum) Testing and Reprting Requirements fr Linear Replacement Lamps Page 7 f 17

8 In-situ Temperature Measurement Test (ISTMT) in selected reference luminaire. Type A, Type B, and Dual-mde tw-ft lamps shall test with three (3) lamps installed. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system. TM-21 Calculatr, apprpriately filled ut ( Testing Ntes Fr Replacement Lamps designed t perate utilizing existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards, and must cmply with applicable ANSI standards. Replacement Lamps that utilize rtatable end caps shuld be tested in the rientatin specified as the default in the manufacturer s installatin instructins. If the installatin instructins d nt specify an rientatin, the lamps shuld be riented straight dwn (this is cmmnly the zer degree setting). DLC reviewers will review the installatin instructins prvided with the applicatin t verify the apprpriate testing rientatin, and cmpare this against dcumentatin in the LM-79 reprt and IES file. Rtatable end cap linear replacement lamp listings will include infrmatin n the testing rientatin in the Ntes field. Fixture Level Tests: Three-Ft Linear Replacement Lamps Please nte, at the time f this release, lamps intended t replace T5-diameter flurescents are nly eligible in the fur-ft categries. Only lamps intended t replace T8 flurescents are currently eligible in the 3-ft categries. All lamps seeking qualificatin must be tested inside in a reference strip fixture. Type A, Type B, and Dual-mde three-ft lamps shall test with tw (2) lamps installed in an apprpriate reference fixture. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system; ne r tw lamp Type C systems are eligible. The reference fixture may be any f the fllwing, r a pre-apprved equivalent: Lithnia C 2 25 MVOLT GEB10IS Lithnia Z 2 25 MVOLT GEB10IS Testing and Reprting Requirements fr Linear Replacement Lamps Page 8 f 17

9 Clumbia CS3-225-EU Clumbia CH3-225-EU Pre-apprved equivalent Pre-apprved Equivalents The DLC des nt endrse r exclude any particular make r mdel f reference fixture. Optins listed are intended t illustrate cmmn fixtures f the apprpriate type. Manufacturers may test in alternative fixtures t thse listed, with preapprval frm the DLC. Pre-apprved fixtures must meet the fllwing cnditins: Alternative fixtures must be cmmnly used in the applicatin categry intended t be applied fr. Dcumentatin may be required t demnstrate fixtures apprpriate use if questins arise. Alternative fixtures must prvide similar thermal envirnments t thse listed. Particularly, alternative fixtures may nt be significantly different in internal vlume r cnstructin materials. Table 3: In-situ Lamp Criteria fr Three-Ft Linear Replacement Lamps In-situ Lamp Criteria fr Three-Ft Linear Replacement Lamps Luminaire Efficacy Minimum Initial Luminaire Light Output 100 lm/w 2 lamps installed x 2,200 lm Spacing Criteria Lumen Maintenance L 70 Znal Lumen Distributin: 0-60 : 40% 50,000 hurs Lumen Maintenance LM-80 fr the package/mdule/array (6,000 hurs minimum) In-situ Temperature Measurement Test (ISTMT) in selected reference luminaire. Type A, Type B, Dual-mde and ne-lamp Type-C three-ft lamps shall test with tw (2) lamps installed. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system. TM-21 Calculatr, apprpriately filled ut ( Testing and Reprting Requirements fr Linear Replacement Lamps Page 9 f 17

10 Testing Ntes Fr Replacement Lamps designed t perate utilizing existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards, and must cmply with applicable ANSI standards. Replacement Lamps that utilize rtatable end caps shuld be tested in the rientatin specified as the default in the manufacturer s installatin instructins. If the installatin instructins d nt specify an rientatin, the lamps shuld be riented straight dwn (this is cmmnly the zer degree setting). DLC reviewers will review the installatin instructins prvided with the applicatin t verify the apprpriate testing rientatin, and cmpare this against dcumentatin in the LM-79 reprt and IES file. Rtatable end cap linear replacement lamp listings will include infrmatin n the testing rientatin in the Ntes field. Fixture Level Tests: Fur-Ft Linear Replacement Lamps All T8 and T5 replacement lamps seeking qualificatin must be tested inside a reference trffer. Type A, Type B, and Dual-mde fur-ft lamps shall test with tw (2) lamps installed in an apprpriate reference trffer. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system; ne, tw, three, and fur lamp Type C systems are eligible. The reference trffer may be any f the fllwing, r a pre-apprved equivalent: Lithnia 2GT8 lensed 2x4 (T8 replacements) Lithnia SP5 lensed 2x4 (T5 replacements) Lithnia 2PM3N 12 cell 2x4 parablic (T8 r T5 versin, as apprpriate) Clumbia Lighting lensed 4PS24 (T8 r T5 versin, as apprpriate) Clumbia Lighting P cell parablic (T8 r T5 versin, as apprpriate) Pre-apprved equivalent A.L.P. EL-2x4-23-* (*= # f lamps) Lithnia 2SP8 G 2 32 A12 XXXX XX XXXX Saylite 131-A-2-32-MV Clumbia Lighting 4PS24 Mnmuth Lighting Crp DCP 22 Simkar Crpratin TY Lensed Trffer 2x4 Testing and Reprting Requirements fr Linear Replacement Lamps Page 10 f 17

11 Jun Lighting Grup S2x4BL LSI GA 2x4 Clumbia Lighting JT824 Visineering Crp. ERCTB 2x4 US Energy Sciences YTR-04-7 Philips Day-Brite 2SPG232-FS01-UNV-1/2EB All T5HO replacement lamps seeking qualificatin must be tested inside a reference high bay. Type A, Type B, and Dual-mde fur-ft lamps shall test with fur (4) lamps installed in an apprpriate reference high bay. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system; three, fur, and six lamp Type C systems are eligible. The reference trffer may be any f the fllwing, r a pre-apprved equivalent: Lithnia IBZT5 4 high bay Clumbia Lighting LHA4-4 (T5HO versin) Pre-apprved equivalent Pre-apprved Equivalents The DLC des nt endrse r exclude any particular make r mdel f reference fixture. Optins listed are intended t illustrate cmmn fixtures f the apprpriate type. Manufacturers may test in alternative fixtures t thse listed, with preapprval frm the DLC. Pre-apprved fixtures must meet the fllwing cnditins: Alternative fixtures must be cmmnly used in the applicatin categry intended t be applied fr. Dcumentatin may be required t demnstrate fixtures apprpriate use if questins arise. Alternative fixtures must prvide similar thermal envirnments t thse listed. Particularly, alternative fixtures may nt be significantly different in internal vlume r cnstructin materials. Testing and Reprting Requirements fr Linear Replacement Lamps Page 11 f 17

12 Table 4: In-situ Testing Requirements: Fur-Ft Linear T8, T5, and T5HO Replacement Lamps In-situ Lamp Criteria Fur-Ft Linear T8 and T5 Replacement Lamps Fur-Ft Linear T5HO Replacement Lamps Luminaire Efficacy 100 lm/w 105 lm/w Minimum Initial Luminaire Light Output Spacing Criteria 2 lamps installed = 3,000 lm 3 lamps installed = 4,500 lm 4 lamps installed = 6,000 lm Spacing Criteria: = = Znal Lumen Distributin: 0-60 : 75% 3 lamps installed = 7,500 lm 4 lamps installed = 10,000 lm 6 lamps installed = 15,000 lm Znal Lumen Distributin: : 30% Lumen Maintenance L70 50,000 hurs 50,000 hurs Lumen Maintenance LM-80 fr the package/mdule/array (6,000 hurs minimum) In-situ Temperature Measurement Test (ISTMT) in selected reference luminaire. Type A, Type B, Dual-mde and ne-lamp Type-C fur-ft lamps shall test with tw (2) lamps installed. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system. TM-21 Calculatr, apprpriately filled ut ( Testing Ntes Fr T8 replacement lamps designed t perate utilizing existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards, and must cmply with applicable ANSI standards. Testing and Reprting Requirements fr Linear Replacement Lamps Page 12 f 17

13 Fr T5 and T5HO replacement lamps designed t perate utilizing existing flurescent ballasts, testing must be cnducted using a nrmal 1.0 ballast factr, electrnic prgrammed-start ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards, and must cmply with applicable ANSI standards. Prduct specificatin sheets must clearly indicate fr which specific linear replacement lamp type (i.e. T8, T5, r T5HO) the prduct is intended, and list the base type and nminal length in inches. Replacement Lamps that utilize rtatable end caps shuld be tested in the rientatin specified as the default in the manufacturer s installatin instructins. If the installatin instructins d nt specify an rientatin, the lamps shuld be riented straight dwn (this is cmmnly the zer degree setting). DLC reviewers will review the installatin instructins prvided with the applicatin t verify the apprpriate testing rientatin, and cmpare this against dcumentatin in the LM-79 reprt and IES file. Rtatable end cap linear replacement lamp listings will include infrmatin n the testing rientatin in the Ntes field. Fixture Level Tests: Eight-Ft Linear Replacement Lamps All eight-ft T8 replacement lamps seeking qualificatin must be tested inside a reference strip fixture using an apprpriate integrating sphere. Additinally, using a gniphtmeter, a fur-ft linear replacement lamp with identical cnstructin as half f the eight-ft linear replacement lamp must be tested inside a reference strip fixture. Representative identical fur-ft linear lamps must be a sellable prduct, with a distinct mdel rdering number, that is marketed and prduced by the same manufacturer. Identical linear lamps, while having the base type G13 as utlined in fur-ft lamp requirements, are defined as having the same type and quantity f driver(s), driving the LEDs at the same current, and having the same number f LEDs and PCBs as half f the eight-ft lamp. The representative lamp must als be f identical cnstructin having identical crss-sectins, the same tube material and thickness, and same heatsink material and extrusin. The gniphtmeter testing results frm the fur-ft strip fixture shall be extraplated t represent the eight-ft strip fixture by multiplying the candela f the fur-ft gniphtmeter utput by a scale factr. That factr shall be derived thrugh dividing the tested lumen utput f the eight-ft strip fixture by the tested lumen utput f the fur-ft strip fixture, as btained frm the integrating sphere. Testing and Reprting Requirements fr Linear Replacement Lamps Page 13 f 17

14 The results must meet the in-situ testing requirements in Table 5. Applicants must prvide results frm the eight-ft testing in the integrating sphere, the fur-ft testing in the integrating sphere, and the fur-ft testing in the gniphtmeter. Prduct specificatin sheets fr bth the fur-ft and eight-ft prducts must be submitted with the applicatin. Applicant must als prvide wrkflw demnstrating the calculatin f the scale factr and identifying, within the phtmetric reprt, the candela values derived via calculatin. In additin, a pht f the eight-ft and fur-ft LED layut side-by-side, as well as a crss sectin diagram f cnstructin fr bth prducts must be submitted. Type A, Type B, and dual mde eight-ft lamps shall test with tw (2) lamps installed in an apprpriate reference strip. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system; ne, and tw lamp Type C systems are eligible. The eight-ft reference strip may be any f the fllwing, r a pre-apprved equivalent: Lithnia C 2 96T8 MVOLT GEB10IS Clumbia CS8-296T8-EU Saylite C 259 MV Pre-apprved equivalent The fur-ft reference strip may be any f the fllwing, r a pre-apprved equivalent: Lithnia C 2 32 MV Clumbia CS4-232-EU Saylite C 232 MV Pre-apprved equivalent Pre-apprved Equivalents The DLC des nt endrse r exclude any particular make r mdel f reference fixture. Optins listed are intended t illustrate cmmn fixtures f the apprpriate type. Manufacturers may test in alternative fixtures t thse listed, with preapprval frm the DLC. Pre-apprved fixtures must meet the fllwing cnditins: Alternative fixtures must be cmmnly used in the applicatin categry intended t be applied fr. Dcumentatin may be required t demnstrate fixtures apprpriate use if questins arise. Alternative fixtures must prvide similar thermal envirnments t thse listed. Particularly, alternative fixtures may nt be significantly different in internal vlume r cnstructin materials. Testing and Reprting Requirements fr Linear Replacement Lamps Page 14 f 17

15 Table 5: In-situ Testing Requirements: Eight-Ft Linear T8 Replacement Lamps In-situ Lamp Criteria fr Eight-Ft Linear T8 Replacement Lamps Luminaire Efficacy Minimum Initial Luminaire Light Output Spacing Criteria Lumen Maintenance L lm/w 2 lamps installed = 6,000 lm Znal Lumen Distributin: 0-60 : 40% 50,000 hurs Lumen Maintenance LM-80 fr the package/mdule/array (6,000 hurs minimum) In-situ Temperature Measurement Test (ISTMT) in selected reference luminaire. Type A, Type B, Dual-mde and ne-lamp Type-C eight-ft lamps shall test with tw (2) lamps installed. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system. TM-21 Calculatr, apprpriately filled ut ( Testing Ntes Fr T8 replacement lamps designed t perate utilizing existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart ballast. Ballasts fr each lamp length, including representative identical lamps, shall be determined fr testing based n the apprpriate ballast fr installatin with that lamp length. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards, and must cmply with applicable ANSI standards. Replacement Lamps that utilize rtatable end caps shuld be tested in the rientatin specified as the default in the manufacturer s installatin instructins. If the installatin instructins d nt specify an rientatin, the lamps shuld be riented straight dwn (this is cmmnly the zer degree setting). DLC reviewers will review the installatin instructins prvided with the applicatin t verify the apprpriate testing rientatin, and cmpare this against dcumentatin Testing and Reprting Requirements fr Linear Replacement Lamps Page 15 f 17

16 in the LM-79 reprt and IES file. Rtatable end cap linear replacement lamp listings will include infrmatin n the testing rientatin in the Ntes field. Fixture Level Tests: U-bend Replacement Lamps All lamps seeking qualificatin must be tested inside in a reference trffer. Type A, Type B, and dual mde U-bend lamps shall test with tw (2) lamps installed in an apprpriate reference trffer. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system. The reference trffer may be any f the fllwing, r a pre-apprved equivalent: Lithnia 2GT8 lensed 2x2 Lithnia 2SP8 lensed 2x2 Lithnia 2PM3 9 cell 2x2 parablic Clumbia Lighting lensed 4PS22 Clumbia Lighting P222 9 cell parablic Pre-apprved equivalent A.L.P. EL-2x2-20-* (*= # f lamps) Saylite 131-A-2-32U-E120 Mnmuth Lighting Crp RF24 Simkar Crpratin TY Lensed Trffer 2x2 Jun Lighting Grup S2x2BL LSI LA/FLA 2x2 Clumbia Lighting JT822 Visineering Crp. ERCTB 2x2 US Energy Sciences YTR-02-5 Pre-apprved Equivalents The DLC des nt endrse r exclude any particular make r mdel f reference fixture. Optins listed are intended t illustrate cmmn fixtures f the apprpriate type. Manufacturers may test in alternative fixtures t thse listed, with preapprval frm the DLC. Pre-apprved fixtures must meet the fllwing cnditins: Alternative fixtures must be cmmnly used in the applicatin categry intended t be applied fr. Dcumentatin may be required t demnstrate fixtures apprpriate use if questins arise. Testing and Reprting Requirements fr Linear Replacement Lamps Page 16 f 17

17 Alternative fixtures must prvide similar thermal envirnments t thse listed. Particularly, alternative fixtures may nt be significantly different in internal vlume r cnstructin materials. Table 6: In-situ Testing Requirements: U-bend Linear Replacement Lamps In-situ Lamp Criteria fr U-bend Linear Replacement Lamps Luminaire Efficacy Minimum Initial Luminaire Light Output Spacing Criteria Lumen Maintenance L lm/w 2 lamps installed: 2,500 lm 3 lamps installed: 3,750 lm Spacing Criteria: = = Znal Lumen Distributin: 0-60 : 75% 50,000 hurs Lumen Maintenance LM-80 fr the package/mdule/array (6,000 hurs minimum) In-situ Temperature Measurement Test (ISTMT) in selected reference luminaire. Type A, Type B, Dual-mde and ne-lamp Type-C U-shaped lamps shall test with tw (2) lamps installed. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system. TM-21 Calculatr, apprpriately filled ut ( Testing Ntes Fr Replacement Lamps designed t perate utilizing existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart T8 ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. Testing and Reprting Requirements fr Linear Replacement Lamps Page 17 f 17